It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

Medical implants made of biodegradable materials could be of advantage for temporary applications such mechanical support during bone-healing or as vascular stents to keep blood vessels open. After completion of the healing process the implant would disappear, avoiding long-term side effects or the need for surgical removal. Various corrodible metal alloys based on magnesium, iron or zinc have been proposed as sturdier and potentially less inflammatory alternative to degradable organic polymers, in particular for load-bearing applications. Despite the recent introduction of magnesium-based screws the remaining hurdles to routine clinical applications are still challenging, such as limiting mechanical material characteristics or unsuitable corrosion characteristics. Here, salient features and clinical prospects of currently investigated biodegradable implant materials are summarized with a main focus on magnesium alloys. A mechanism of action for the stimulation of bone growth due to the exertion of mechanical force by magnesium corrosion products is discussed. To explain divergent in vitro and in vivo effects of magnesium a novel model for bacterial biofilm infections is proposed which predicts crucial consequences antibacterial implant strategies.

We investigate the exact travelling wave solutions of the Tzitzéica-Dodd–Bullough–Mikhailov (TDBM) and Tzitzéica-type (TT) equations, appear in nonlinear optics, using simple ansatz approach. We use the Painlevé and traveling wave transformations to convert the mentioned nonlinear equations into nonlinear ordinary differential equations. Then, the simple ansatz approach has been employed to procure wave solutions, in terms of bright, singular soliton and trigonometric functions, for the Tzitzéica-Dodd–Bullough–Mikhailov (TDBM) and Tzitzéica-type (TT) equations. The study shows that the simple ansatz approach is straightforward and easy to implement for solving nonlinear problems.

The research community has shown significant interest in the aqueous synthesis of nanomaterials due to its ability to eliminate the need for complex organic solvents. This synthesis approach aligns with the principles of green chemistry, attracting considerable attention. Aqueous solution technology in fabricating nanostructures has gained recognition for its potential to create ultrasensitive, low-energy, and ultrafast optoelectronic devices. This report focuses on synthesizing lead iodide (PbI2) nanoplates using a water-based solution technique and fabricating a planar photodetector. The photodetectors with a planar type of device structure (ITO/PbI2 NPs/Au) demonstrated a remarkable photosensitivity of 3.9×103 and a photoresponsivity of 0.51 mA/W at a wavelength of 405 nm. Notably, the asymmetrical output properties of ITO/PbI2 NPs/Au detector deliver additional evidence of the effective creation of a Schottky contact. Thus, the photodetector exhibited a photoresponse even at 0 V bias, leading to the realization of self-powered photodetectors. Additionally, the device exhibited a rapid photoresponse of 0.21/0.38 s (−5 V) in the visible range. This study has expanded the horizons for the aqueous-phase synthesis of nanoplate nanostructures, enabling the large-area fabrication of high-performance photodetectors.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

Cesium lead iodide (CsPbI3) perovskite nanocrystals (NCs) are a promising material for red light-emitting diodes (LEDs) due to their excellent color-purity and high luminous efficiency. However, small-sized CsPbI3 colloidal NCs, such as nanocubes, used in LEDs suffer from confinement effects, negatively impacting their photoluminescence quantum yield (PLQY) and overall efficiency. Here, we introduced YCl3 into the CsPbI3 perovskite, which formed anisotropic, one-dimensional (1D) nanorods. This was achieved by taking advantage of the difference in bond energies between Cl− and I− ions, which caused YCl3 to promote the anisotropic growth of CsPbI3 NCs. The YCl3-based nanorods improved the PLQY and storage stability by passivating the defects reducing the nonradiative recombination rates. When the YCl3-substituted CsPbI3 nanorods are applied to the emissive layer in LEDs, we achieve an external quantum efficiency of ~3.16% which is 1.86-fold higher than the pristine CsPbI3 NCs (1.69%) based LED. Notably, the ratio of horizontal transition dipole moments (TDMs) in the anisotropic YCl3:CsPbI3 nanorods was determined to be 75%, which is higher than the isotropically oriented TDMs in CsPbI3 nanocrystals (67%). This increased TDM ratio led to higher light outcoupling efficiency in nanorods-based LEDs. Overall, the results suggest that YCl3-substituted CsPbI3 nanorods could be promising for achieving high-performance perovskite LEDs.

Heavy metals have adverse effects on microalgae growth and metabolism. Photosynthesis and lipid profile are quite sensitive to heavy metal toxicity. The impact of chromium (Cr) on growth and photosynthetic activity of Dictyosphaerium pulchellum and Micractinium pusillum exposed to different concentrations (0 – 500 μg L-1) was investigated for 11 days. The influence of Cr on cell density and cell number followed similar trends, indicating a possible correlation among these growth responses. A significant (p < 0.05) increase in lipid content was observed with the increasing concentration of Cr however, growth was suppressed at higher concentrations exceeding 100 μg L-1. Addition of Cr in the cell culture medium showed a negative effect on quantum yield (Fv/Fm) and a photosynthetic inhibition of > 65% was noted in both species at 500 μg L-1. However, the lipid gravimetric analysis presented inner cell lipid content up to 36% and 30% of dry weight biomass for D. pulchellum and M. pusillum, respectively. The effects of chromium on growth and lipid accumulation in both microalgae species was concentration and exposure time dependent. This shows that an appropriate concentration of chromium in culture medium could be beneficial for higher lipid accumulation in freshwater eukaryotic microalgae species.

Herein, we have fabricated graphitic carbon nitride (g-C3N4) nanosheets with embedded ZnCdS nanoparticles to form a type II heterojunction using a facile synthesis approach and used for photocatalytic H2 production. The morphologies, chemical structure and optical properties of the obtained g-C3N4‒ZnCdS samples were characterized by a battery of techniques such as, TEM, XRD, XPS and UV-Vis DRS. The as-synthesized g-C3N4‒ZnCdS, photocatalyst exhibits the highest hydrogen production rate of 108.9 μmol·g-1·h-1 compared to individual components (g-C3N4: 13.5 μmol·g-1·h-1, ZnCdS: 45.3 μmol·g-1·h-1). The improvement of its photocatalytic activity is mainly attributed to the heterojunction formation and resulting synergistic effect, which provide more channels for charge carrier migration and reduce the recombination of photogenerated electrons and holes. Meanwhile, the g-C3N4‒ZnCdS heterojunction catalyst also showed higher stability over a number of repeated cycles. Our work sheds insight of using g-C3N4 and metal sulfide combination to develop low-cost, efficient, visible-light active hydrogen production photocatalysts.

Gambogic acid, a common traditional Chinese medicine and widely distributed throughout South China, Vietnam, Cambodia, and Thailand. It is prenylated xanthone which is the significant bioactive compound of gamboge. Gambogic acid is known as a strong apoptotic inducer in cancer cells. It has been found as strong anticancer agent against various types of cancer cells lines such as breast cancer, pancreatic, and cervical cancer. It induces apoptosis, down regulates the anti-apoptotic proteins (survivin and BCL2,) and down regulates the activities of P-glycoprotein in drug sensitive human breast MCF-7 and drug-resistant MCF-7/ADR cells. Similarly, it also exerts alteration in P13K, AKT, p21, MMP-2 &-9, and phosphorylated-AKT expressions. The current review highlights the anticancer and chemo-preventive perspectives of gambogic acid and its mechanistic role against human and animal cancers.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

In mice, mutations or targeted disruptions of the core circadian gene Bmal1 have been implicated in early onset of ocular pathologies, including premature/congenital cataract development. The aim of the present study was to analyze probands of consanguineous Pakistani cataract families to identify the novel pathogenic variants in the BMAL1 gene. We have studied 21 congenital cataract families. Ophthalmic examination was performed for the probands and available family members. Genomic DNA was isolated from peripheral blood. PCR and Sanger sequencing was performed for the entire coding region of the BMAL1 gene. Targeted Sanger sequencing of BMAL1 revealed a heterozygous variant c.41A>T; p.(Asp14Val) in one proband, but it did not co-segregate with the disease phenotype in the family. In addition, a nonsynonymous variant (rs2290037) was identified in five probands. Our study is the first one to analyze the role of BMAL1 gene mutations in humans for their association with congenital cataract. Although we were unable to find the variants associated with congenital cataract families from Pakistan, more studies from other populations will be informative to further prove the role of BMAL1 with the disease.

We report photon-phonon atomic coherence (cascade- and nested-dressing) interaction from various phase transitions of Eu3+: BiPO4 crystal. Such atomic coherence spectral interaction evolves from out of phase fluorescence to in-phase spontaneous four-wave mixing (SFWM) by changing the time gate. The dressing dip switch and three dressing dips of SFWM result from strong photon-phonon destructive cross- and self-interaction for hexagonal phase, respectively. The more phonon dressing result in destructive interaction, while less phonon dressing result in constructive interaction of atomic coherences. The experimental measurements of photon-phonon interaction agree with theoretical simulations. Based on our results, we proposed a model for an optical transistor (as an amplifier and switch).

Emotion detection from the text is an important and challenging problem in text analytics. The opinion-mining experts are focusing on the development of emotion detection applications as they have received considerable attention of online community including users and business organization for collecting and interpreting public emotions. However, most of the existing works on emotion detection used less efficient machine learning classifiers with limited datasets, resulting in performance degradation. To overcome this issue, this work aims at the evaluation of the performance of different machine learning classifiers on a benchmark emotion dataset. The experimental results show the performance of different machine learning classifiers in terms of different evaluation metrics like precision, recall ad f-measure. Finally, a classifier with the best performance is recommended for the emotion classification.

The 10-valent pneumococcal vaccine was introduced in Pakistan’s Expanded Program on Immunization (EPI) in 2013 as a 3+0 schedule without catchup. We conducted three annual cross-sectional surveys from 2014-2016 to measure vaccine-type (VT) carriage in infants from a rural part of Pakistan. Nasopharyngeal specimens were collected by random sampling of infants from 2 union councils of Matiari. Samples were then transported to Infectious Disease Research Laboratory (IDRL) at the Aga Khan University within 6-8 hours of collection. Serotypes were established using sequential multiplex PCR. Of the 665 children enrolled across three surveys, 547 were culture positive for pneumococcus. VT carriage decreased from 21·8% in 2014 to 12·7% in 2016 (p-value for trend <0·001). Those who were not vaccinated or partially vaccinated were found to be at higher risk of carrying a VT serotype (aOR 2·53, 95% CI 1·39, 4·63 for non-vaccinated) and (aOR 3·35, 95% CI 1·82, 6·16 for partially vaccinated). On the other hand, being enrolled in the most recent survey was negatively associated with VT-carriage (aOR 0·51, 95% CI 0·28, 0·93). We found that PCV10 was effective in decreasing the carriage of vaccine-type serotypes in Pakistani infants.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Delivering nucleic acid therapeutics across cell membranes is a significant challenge. Cell-penetrating peptides (CPPs) containing arginine (R), tryptophan (W), and histidine (H) show promise for siRNA delivery. To improve siRNA delivery and silencing a model STAT3 gene, we hypothesized that oleyl acylation to CPPs, specifically (WRH)n, would enhance STAT3 silencing efficiency in breast and ovarian cancer cells. Using Fmoc/tBu solid-phase peptide chemistry, we synthesized, purified, and characterized the oleyl-conjugated (WRH)n (n = 1-4) peptides. The peptide:siRNA complexes were non-cytotoxic at N/P 40 (~20 μM) against MDA-MB-231, MCF-7, SK-OV-3, and HEK-293 cells after 72 h incubation. All peptide:siRNA complexes showed serum stability at N/P ≥40. The synthesized conjugates, with a diameter of &lt;100 nm, formed nano complexes with siRNA and exhibited stable range of zeta potential values (13-18 mV at N/P 40). Confocal microscopy and flow cytometry analysis provided qualitative and quantitative evidence of successful cellular internalization of siRNA. Peptides oleyl-(WRH)3 and oleyl-(WRH)4 showed ~60% and ~75% cellular uptake of siRNA, respectively, in both MDA-MB-231 and SK-OV-3 cells. Western blot analysis of oleyl-(WRH)4 demonstrated effective silencing of the STAT-3 gene, with ~75% silencing in MDA-MB-231 cells and ~45% in SK-OV-3 cells.