Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

Compared with conventional methods of fault diagnosis for power transformers, which have defects such as imperfect encoding and too absolute encoding boundaries, this paper systematically discusses various intelligent approaches applied in fault diagnosis and decision making for large oil-immersed power transformers based on dissolved gas analysis (DGA), including expert system (EPS), artificial neural network (ANN), fuzzy theory, rough sets theory (RST), grey system theory (GST), swarm intelligence (SI) algorithms, data mining technology, machine learning (ML), and other intelligent diagnosis tools, and summarizes existing problems and solutions. From this survey, it is found that a single intelligent approach for fault diagnosis can only reflect operation status of the transformer in one particular aspect, causing various degrees of shortcomings that cannot be resolved effectively. Combined with the current research status in this field, the problems that must be addressed in DGA-based transformer fault diagnosis are identified, and the prospects for future development trends and research directions are outlined. This contribution presents a detailed and systematic survey on various intelligent approaches to faults diagnosing and decisions making of the power transformer, in which their merits and demerits are thoroughly investigated, as well as their improvement schemes and future development trends are proposed. Moreover, this paper concludes that a variety of intelligent algorithms should be combined for mutual complementation to form a hybrid fault diagnosis network, such that avoiding these algorithms falling into a local optimum. Moreover, it is necessary to improve the detection instruments so as to acquire reasonable characteristic gas data samples. The research summary, empirical generalization and analysis of predicament in this paper provide some thoughts and suggestions for the research of complex power grid in the new environment, as well as references and guidance for researchers to choose optimal approach to achieve DGA-based fault diagnosis and decision of the large oil-immersed power transformers in preventive electrical tests.

Selected by in vitro techniques (SELEX, cell-SELEX), aptamers are strands of DNA or RNA molecules able to bind a wide range of targets, from small molecules to live cells, and even tissues, with high affinity and specificity. Due to their efficient targeting ability, aptamers are extensively used in different fields of applications. For example, they ensure high performance as cancer-related markers or in recognizing cancer cells. Actually, they represent a promising way for early diagnosis (biosensors) and to deliver imaging agents and drugs, in both cancer imaging and therapy (therapeutic aptamers). Aptamer-based biosensors (aptasensors) have attracted particular attention over the last decades, so as the possibility of using aptamers in disease therapy in substitution of monoclonal antibodies. The paper briefly reviews the most recent literature on this topic, both concerning the advances in biomedical applications and in the development of electrical aptasensors. The investigation concerning the bioelectronics features of aptamers, to be implemented in the development of electrical nanobiosensors, is also reviewed. To this aim, some recent results of a theoretical/computational framework for modelling the electrical properties of biomolecules (Proteotronics) are reported.

Various type of soils have been identified based on their electrical and magnetic properties, especially with regards to peat soils. Peat soils are commonly considered as partly decomposed vegetation. In this study, electrical and magnetic properties have been used in K-means clustering to identify layers of peat soils. K-means clustering is a partitioning method that treats observations in the data. Data cores were obtained at every centimeter and examined for their electrical conductivity (σ) and magnetic susceptibility (χ_m) properties. A 291 cm core was obtained at Tegal Arum Village in South Kalimantan, Indonesia. The K-means clustering results indicate two different layers at 148 cm, and this is supported by loss on ignition (LOI) measurements. In the first layers, a 87.65% LOI was found associated with peat soils (above 248 cm). Whereas, in the second layers, there was a 26.11% LOI associated with mineral soils (below 248 cm). The results of this study using K-means clustering can be used to delineate soil layers.

Winding design methods have been a subject of research for many years of the past century. Many methods have been developed, each one characterized by some advantages and some drawbacks. Nowadays, the star of slots is the most widespread design tool for electrical machine windings. In this context, this paper presents a simple and effective procedure to determine the distribution of the EMF stars and of the winding configuration in all possible typologies of electrical machines equipped with symmetrical windings. Moreover, this procedure can also be easily implemented in a computer program in order to perform automated winding designs for rotating electrical machines. Several examples are provided in order to validate the proposed procedure.

We report on the development of chemical vapour deposition (CVD) based graphene field effect transistor (GFET) immunosensors for the sensitive detection of Human Chorionic Gonadotropin (hCG), a glycoprotein risk biomarker of certain cancers. The GFET sensors were fabricated on Si/SiO₂ substrate using photolithography with evaporated chromium and sputtered gold contacts. GFET channels were functionalized with a linker molecule to immobile anti-hCG antibody on the surface of graphene. Binding reaction of the antibody with varying concentration levels of hCG antigen demonstrated the limit of detection of the GFET sensors to be below 1 pg/mL using four-probe electrical measurements. We also show annealing can significantly improve the carrier transport properties of GFETs and shift the Dirac point (Fermi level) with reduced p-doping in back-gated measurements. The developed GFET biosensors are generic and could find applications in a broad range of medical diagnostics in addition to cancer, such as neurodegenerative (Alzheimer’s, Parkinson’s and Lewy body) and cardiovascular disorders.

Maintenance of intestinal barrier integrity is crucial for preventing inflammatory bowel diseases (IBDs) onset and exacerbations. In this work we study the effect of a fixed combination of Lactobacillus reuteri and Lactobacillus acidophilus and herbal extracts in an in vitro inflammation experimental model. Caco-2 cell monolayer was exposed to INF-γ+TNF-α or to LPS; Trans Epithelial Electrical Resistance (TEER) and paracellular permeability were investigated. ZO-1 and occludin tight junctions (TJs) were also investigated by mean of immunofluorescence. The pre-treatment with the fixed combination of probiotics and herbal extracts prevented the inflammation-induced TEER decrease, paracellular permeability increase and TJs translocation. In summary the fixed combination of probiotics and herbal extracts investigated in this research was found to be an interesting candidate for targeting the re-establishment of intestinal barrier function in IBDs conditions.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

During flux weakening operation time (FWOT), the total iron loss rises and affects the accuracy of loss prediction and efficiency especially if a large range of FWOT exists. Iron loss prediction is widely employed in investigations for a fast electrical machine analysis using 2-D FEA. This paper studies harmonic loss analytically by a steady-state equivalent circuit. Consideration of skin effects and iron saturation are utilized in order to examine the accuracy through the relative error distribution in the frequency domain of each model from 50 to 700 Hz. Additionally, this comparative study presents a torque-frequency-flux density calculation over each single term of the modified IEM-formula. The analytical calculation is performed using 2-D FEA for a classic and modified IEM-formula along with experimental verifications on a surface-mounted PMSG for a wind generation application.

Aeromagnetic data coupled with Landsat ETM+ data and SRTM DEM have been processed in order to map regional hydrogeological structures in the basement complex region of Paiko, north-central Nigeria. Lineaments were extracted from derivative maps from aeromagnetic, Landsat ETM+ and SRTM DEM datasets. Ground geophysical investigation utilizing Radial Vertical Electrical Sounding (RVES) was established in nine transects comprising of four sounding stations which are oriented in three azimuths. Source Parameter Imaging (SPI) was employed to map the average depths structures from aeromagnetic dataset. Selected thematic layers which included lineaments density, lithologic, slope, drainage density and geomorphologic maps were integrated and modelled using ArcGIS to generate groundwater potential map of the area. Groundwater zones were classified into four categories: very good, good, moderate and poor according to their potential to yield sustainable water to drilled wells. Results from RVES survey reveal a close correlation to lineaments delineated from surface structural mapping and remotely sensed datasets. Hydrogeological significance of these orientations suggest that aeromagnetic data can be used to map relatively deep-seated fractures which are likely to be open groundwater conduits while remotely sensed lineaments and orientations delineated from the RVES survey may indicate areas of recharge. Regions with high lineament density have relatively better groundwater potential. This is attributable to areas having deep weathering profiles associated with intrusive bodies that have resulted in intense fracturing in the area. Drill depths in this area should target a minimum of 80 m to ensure sufficient and sustainable supplies to drilled wells. The outcome of this study should act as information framework that would guide the siting of productive water wells and while providing needed information for relevant agencies in need of data for the development of groundwater resources.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

With the widespread use of electric machines there is a growing need to extract information from the machines to optimize their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of an squirrel cage induction motor rotor physical variables. The system comprises: circuit to acquire desirable rotor variable(s) value(s) and send it to the computer; a rectifier and power storage circuit that besides converting an alternating current in continuous also store energy for a certain amount of time to wait the motor engine shutdown; and magnetic generator that harvest energy from rotating field to power the circuits mentioned above. The embedded system is set on the rotor, making it difficult to power the system because it is rotating, problem solved with the construction of the magnetic generator eliminating the need of using batteries or collector rings and send data to the computer using a wireless NRF24L01 module. For the proposed system validation a temperature sensor (DS18b20) was used, variable known as the most important when identifying the need for maintenance and control systems. Tests were made getting satisfactory results proving the viability of using sensors on the rotor.

Flux-switching permanent magnet (FSPM) motors have gained increasing attention in the electric vehicles (EVs) applications due to the advantages of high power density, high efficiency. However, the heat sources of both permanent magnet (PM) and armature winding are located on the limited stator space in the FSPM motors, which may result in the PM overheated and irreversible demagnetization caused by temperature rise and it is often ignored in the conventional thermal analysis. In this paper, a new electrical-thermal two-way coupling design method is proposed to analyze the electromagnetic performances, where the change of PM material characteristics under different temperatures is taken into consideration. Firstly, the motor topology and design equations are introduced. Secondly, the demagnetization curves of PM materials under different temperatures are modeled due to PM materials are sensitive to the temperature. And based on the electrical-thermal two-way coupling method, the motor performances are evaluated in details, such as the load PM flux linkage and output torque. Then, the motor is optimized, and the electromagnetic performances between initial and improved motors are compared. Finally, a prototype motor is manufactured, and the results are validated by experimental measurements.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Recently, design of electric scooters (ESs) has commonly adopted brushless DC motors (BLDCMs) in place of brushed DC motors. This invention develops a new anti-lock braking system (ABS), based on a slip-ratio estimator, for ES utilizing the braking force generated by the BLDCM when electrical energy releases to the load yielding an analogous effect of ABS control in gas-engine vehicles. Comparing to mechanical ABS, the design possesses the advantages of rapid torque responses due to fast actuating response. The electrical ABS is realized by associating with kinematic and Short-circuit braking. A current controller is used to adjust the braking force, while the sliding mode control strategy is adopted to regulate the slip ratio for best road adhesion while braking. Real-world experiments have been conducted for functional and performance verification.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.