Ferroelectric materials are crucial for today’s technological society, and nanostructured ferroelectric materials are important for downscaling of devices. Controlled and reproducible synthesis of these materials are therefore of immense importance. Hydrothermal synthesis is a well-established synthesis route, with a large parameter space for optimization, but a better understanding of nucleation and growth mechanisms is needed for full utilization and control. Here we use in situ X-ray diffraction to follow the nucleation and growth of BaTiO₃ formed by hydrothermal synthesis using two different titanium precursors, an amorphous titania precipitate slurry and a Ti-citric acid complex solution. Sequential Rietveld refinement was used to extract the time dependency of lattice parameters, crystallite size, strain and atomic displacement parameters. Phase pure BaTiO₃ nanoparticles 10 - 15 nm in size were successfully synthesized at different temperatures (100, 125, and 150 °C) from both precursors after reaction times ranging from a few seconds, to several hours. The two precursors resulted in phase pure BaTiO₃ with similar final crystallite size. Finally, two different growth mechanisms were revealed, where the effect of surfactants present during hydrothermal synthesis is discussed as one of the key parameters.

Maximum likelihood estimation (MLE) is a popular method for parameter estimation in both applied probability and statistics but MLE cannot solve the problem of incomplete data or hidden data because it is impossible to maximize likelihood function from hidden data. Expectation maximum (EM) algorithm is a powerful mathematical tool for solving this problem if there is a relationship between hidden data and observed data. Such hinting relationship is specified by a mapping from hidden data to observed data or by a joint probability between hidden data and observed data. In other words, the relationship helps us know hidden data by surveying observed data. The essential ideology of EM is to maximize the expectation of likelihood function over observed data based on the hinting relationship instead of maximizing directly the likelihood function of hidden data. Pioneers in EM algorithm proved its convergence. As a result, EM algorithm produces parameter estimators as well as MLE does. This tutorial aims to provide explanations of EM algorithm in order to help researchers comprehend it. Moreover some improvements of EM algorithm are also proposed in the tutorial such as combination of EM and third-order convergence Newton-Raphson process, combination of EM and gradient descent method, and combination of EM and particle swarm optimization (PSO) algorithm.

High-throughput research on bimetallic nanoparticles brought a vast overview of their characteristics and catalytic activities.¹ However, traditional bimetallic nano-allloy quantification methods serving catalyst preparations are not suitable for the fast and robust data output of high-throughput experiments. Hence, this work designed and validated a more fast, more neat, and reliable quantitative analysis using X-ray fluorescence spectroscopy for bimetallic nanoparticles synthesized by high-throughput setups. The results demonstrated this method to be accurate with high precision. Furthermore, the agreement to qualitative results from an energy-dispersive X-ray spectrometer equiped on a scanning electron microscope provided an option to quantify a bimetallic nano-alloy by just analyzing one of the two composing elements. Thus, this method is proved to be highly compatible with high-throughput experiments.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

Extensive in-situ resource utilisation (ISRU) will be essential to enable long-duration stays on Luna and Mars and reduce reliance on resupply from Earth. Early development of ISRU technologies has focused on standalone capabilities for specific targets related to life support and ascent propellant. An unexplored opportunity remains for greatly expanding the scope of materials that can be supplied by ISRU, and for integrating various technology platforms into a larger system. Recent advances in power-to-X technology aimed at decarbonising the global economy have made it possible to drive key chemical processes using electricity with small-scale, modular reactor. This paper proposes a vision for an integrated system of ISRU processes based on power-to-X technology to produce oxygen, hydrogen, water, methane, polymers, metal alloys, and synthetic fertilisers, using Martian regolith, atmosphere, and ice. A ‘building block’ strategy is adopted to convert raw materials into versatile intermediaries, which can then be combined to form essential products. A wider range of raw materials are available on Mars compared to Luna, suggesting greater opportunity for ISRU deployment to compensate for the greater time and cost requirements for a Mars resupply mission.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

Finding new, safe strategies to prevent and control rheumatoid arthritis is an urgent task. Of particular interest in this regard are bioactive peptides and peptide-rich protein hydrolyzates, which represent a new trend in the development of functional foods and nutraceuticals. The resulting tissue hydrolyzate of the chicken embryo (CETH) has been evaluated for acute toxicity and tested against chronic arthritis induced by Freund's full adjuvant in rats. The anti-arthritic effect of CETH was studied on the 28th day of the experiment after two weeks of oral administration of CETH at doses of 60 and 120 mg/kg body weight. Arthritis was evaluated on the last day of the experiment on the injected animal paw using X-ray computerized microtomography and histopathology analysis methods. The CETH effect was compared with the non-steroidal anti-inflammatory drug diclofenac sodium (5 mg/kg). Oral administration of CETH was accompanied by effective dose-dependent correction of morphological changes caused by the adjuvant injection. CETH had relatively high recovery effects in terms of parameters for reducing inflammatory edema, inhibition of osteolysis, prevention of osteophitosis, reduction of the inflammatory reaction of periarticular tissues, and cartilage degeneration. This study presents a potential theoretical strategy for the safe correction of this pathological process and, for the first time, shows that CETH may be a powerful potential nutraceutical agent or bioactive component of functional products in the treatment of rheumatoid arthritis.

Kininogens are multidomain glycoproteins found in the blood of most vertebrates. They are important in the blood coagulation cascade pathways - in intrinsic pathway activation leading to thrombin generation partially independently from tissue factor dependent extrinsic pathway, connecting blood coagulation with the kallikrein-kinin system. Nothing is known about the shape on atomic level therefore the endeavor to obtain the good-quality spatial structure of kininogens is important for a better understanding of their role in disease and treatment. Application of cryo-EM is important for solving the spatial structure of kininogens, drawing new frontiers in understanding the function and opening new pathways for drug development.

This study sought to improve the nutritional, functional and biochemical properties of pearl millet through malting and fermentation. Moringa oleifera leaf powder (MLP) was used as a fortificant. Mixture design was used to find optimal proportions for each of the components that yield a high protein and or low saturated fat content. Twelve mixtures with varying ratios of fermented, and malted pearl millet flour ranging between 30–65%, and MLP between 5–15% were generated through I-Optimal mixture design. The mixtures were wet-cooked, freeze-dried and analyzed for protein and fat content. The data obtained were fitted to a linear mixture model and the search for the optimum was done using Numerical Optimization for maximising protein and minimising saturated fat. The linear model was suitable for explaining variation for total protein and saturated fat with r2 of 0.50 and 0.51, respectively. Increasing MLP increased protein content. Two final formulations were generated through the optimization process. Pearl millet’s protein content increased by up to 22% while saturated fat decreased by up to 13%. Ash content increased by 75%. Polyphenol content and oxygen radical absorbance capacity increased by 80% and 25%, respectively. Final and peak viscosity were reduced by 90% and 95%, respectively.

Gelatin industry residues are increasingly used as fertilizer and soil conditioner. However, correct residue dosage is critical for grass development and minimizing environmental impacts. This randomized block design study determined adequate dosage of Mixed Gelatin Sludge (MGS) for Marandu grass production in wet/dry seasons in Brazil. Five MGS levels (0%–200% of required nitrogen) were compared to mineral fertilizer. Agronomic/productivity characteristics, bromatological composition, macro/micro-nutrient composition of leaves, and soil chemical attributes were evaluated. Agronomic/productivity characteristics were influenced by MGS dose in both dry/rainy seasons, except for leaf blade pseudostem ratio and percentage of leaves/pseudostem. Bromatological composition was influenced by MGS doses in dry/rainy seasons except for dry/mineral material quantities. Marandu leaf tissue chemical composition was significantly influenced by MGS dose, except for potassium, boron, and iron. Chemical composition of four soil layers between 0–50 cm influenced GMS dose, except for pH, organic matter, magnesium, copper, manganese, and zinc. GMS dose for Marandu production should be 200% of nitrogen (N) requirement. GMS application increased productivity/quality of Marandu grass. Macronutrients (N, phosphorus) and micronutrients (Ca, Mg, S, Cu, and Zn) increased in Marandu grass and in the soil (Ca, S, and Na). Increased sodium (Na) level was not limiting.

A wide variety of pump and treat methods like chemical precipitation, adsorption, ion exchange and reverse osmosis have been trialled for many decades for fluoride removal from groundwater, but the problem of fluoride contaminated water remains in many parts of the world largely because these processes require constant monitoring, are expensive to implement and maintain at decentralised scale due to lack of reticulation infrastructure, and possess sludge disposal problem. This paper presents an overview of various fluoride removal processes and the limitations associated with each process and the application of in-situ permeable reactive barrier for remediating fluoride contaminated groundwater is explored, which displays the potential to be a cost effective, low maintenance and energy intensive technology.

Understanding the genotype x environment (GE) interaction for traget trait is valuable for growers, agronomists, breeders and the seed industry. The objective of this study was to see and explore the genotype x environment interaction for grain yield of wheat to better guide genotype selection and breeding. The genotype main effect and GE interaction effect (GGE) biplots resolved the following three genotypes: 85 (ETW17-377), 82 (ETW17-374) and 13 (ETW17-281) for being the best yielding and stable. The Kulumsa site planted on 4^th of July 2017 (environment 7=E7) and the DebreZeit site on 20^th of July 2017 (E3) were the most effective environments in distinguishing the test genotypes and are thus suitable environments for future evaluation and selection with specific adaptation. Melkasa site planted on 4^th July (E9) was a representative environment where genotypes can be evaluated for wide adpaptation. The genetic covariate biplot indicated that thousand kernel weight (TKW) and plant height (PH) had significant positive associations with grain yield implying the possible concurrent indirect selection of both traits for exploiting GE interaction for grain yield of wheat.

We investigate numerically the interactions of in-phase Airy beams modulated by a fundamental Gaussian beam and fourth-order diffraction in Kerr nonlinear media. Directly numerical simulations show that normal (anomalous) fourth-order diffractions and in-phase (out-of-phase) Gaussian beam affect the interactions of solitons generated from Airy beams in unique manners. Different from previous results that interactions between in-phase (out-of-phase) conventional beams are always attractive (repulsive), many anomalous interactions of Airy beams are obtained. Stable bound states of breathing Airy soliton pairs can be formed with the help of fourth-order diffraction and fundamental Gaussian beam.

Abstract: The SARS-CoV-2 pandemic has reemphasized the urgent need for broad-spectrum antiviral therapies. We developed a computational workflow using scRNA-Seq data to assess cellular metabolism during viral infection. With this workflow we predicted the capacity of cells to sustain SARS-CoV-2 virion production in patients and found a tissue-wide induction of metabolic pathways that support viral replication. Expanding our analysis to influenza A and dengue viruses, we identified metabolic targets and inhibitors for potential broad-45 spectrum antiviral treatment. These targets were highly enriched for known interaction partners of all analyzed viruses. Indeed, phenformin, an NADH:ubiquinone oxidoreductase inhibitor, suppressed SARS-CoV-2 and dengue virus replication. Atpenin A5, blocking succinate dehydrogenase, inhibited SARS-CoV-2, dengue virus, respiratory syncytial virus, and influenza A with high selectivity indices. In vivo, phenformin showed antiviral activity against SARS-CoV-2 in a Syrian hamster model. Our work establishes host metabolism as druggable for broad-spectrum antiviral strategies, providing invaluable tools for pandemic preparedness.

Centrifugal pumps are widely employed in the oil refinery industry due to their efficiency and effectiveness in fluid transfer applications. The reliability of pumps plays a pivotal role in ensuring uninterrupted plant productivity and safe operations. Analysis of failure history data shows that bearings have been identified as critical components in oil refinery pump groups. However, traditional reliability estimation theories may not apply when data is limited or subject to right censoring. This paper addresses the complexity of estimating the Weibull distribution parameters using the maximum-likelihood method under the abovementioned conditions. The likelihood equation lacks an explicit analytical solution, necessitating the use of numerical methods for resolution. The proposed approach presented in this article leverages the Expectation-Maximization (EM) algorithm for estimating the Weibull distribution parameters. This method provides more accurate estimates of failure rates and probabilities by accounting for limited and censored data. The findings are demonstrated through a case study, showcasing the practical application of the proposed approach.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Conditional generative adversarial networks (CGANs) learn a mapping from conditional input to observed image and perform tasks in image generation, manipulation and translation. In-situ monitoring uses sensors to obtain real-time information of additive manufacturing (AM) processes that relate to process stability and part quality. Understanding the correlations between process inputs and in-situ process signatures through machine learning can enable experimental-driven predictions of future process inputs. In this research, in-situ data obtained during a metallic powder bed fusion AM process is mapped with a CGAN. A single build of two turbine blades is monitored using EOSTATE Exposure OT, a near-infrared optical tomography system of the EOS M290 system. Layerwise images generated from the in-situ monitoring system were paired with a conditional image that labeled the specimen cross-section, laser-scan stripe overlap and z-distance to part surfaces. A CGAN was trained using the turbine blade data set and employed to generate new in-situ layerwise images for unseen conditional inputs.

Knowledge of permafrost’s ice and unfrozen water content is critical for predicting the permafrost behavior during ice–water–ice transition. This is especially relevant when ice and permafrost are melting in many regions under the influence of global warming. It is well-known that only a part of the formation's pore water turns into ice at 0 ^oC. After the further lowering the temperature, the water phase transition continues, but at gradually decreasing rates. Thus, the porous space is filled with ice and unfrozen water. The laboratory data show that frozen formations' mechanical, thermal, and rheological properties strongly depend on the moisture content. Hence, porosity and temperature are essential parameters of permafrost. In this paper, it is shown how, and by combining research in three fields: (1) geophysical exploration, (2) numerical modeling, and (3) temperature logging, it is possible to estimate in-situ the porosity of permafrost. To demonstrate the procedure, five examples of numerical modeling (where all input parameters are specified) are given. This investigation is the first attempt to analyze the permafrost’s porosity in situ quantitively.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

MoS₂/TiO₂ nanostructures made of MoS₂ nanoparticles covering TiO₂ nanosheets have been synthesized, either via ex-situ or in-situ approaches. Morphology and structure of MoS₂/TiO₂ hybrid nanostructures have been investigated and imaged by means of X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM), while the vibrational and the optical properties have been investigated by Raman, Fourier-transform infrared spectroscopy (FTIR) and UV−visible (UV-Vis) techniques. The different stacking degrees together with the size distribution of the MoS₂ nanosheets, decorating the TiO₂ nanosheets, have been carefully obtained from HRTEM images. The nature of the surface sites on the main exposed faces of both materials has been detected by means of in-situ FTIR spectra of adsorbed CO probe molecule. The results coming from the ex-situ and in-situ approaches will be compared, by highlighting the role of the synthesis processes in affecting morphology and structure of MoS₂ nanosheets, including their curvature, surface defects, and stacking order. Some more, it will be shown that the in-situ approach is affecting the reactivity of the TiO₂ nanosheets too, hence in turn affects the MoS₂/TiO₂ nanosheets interaction.

Fragile X syndrome (FXS), the most common monogenic cause of inherited intellectual disability and autism spectrum disorder, is caused by a full mutation (>200 CGG repeats) in the Fragile X Messenger Ribonucleoprotein 1 (FMR1) gene. Individuals with FXS experience a wide range of challenges related to social interaction (SI). Animal models, such as Drosophila melanogaster model for FXS where the only ortholog of human FMR1 (dFMR1) is mutated, have played a crucial role in understanding of FXS. The aim of this study was to investigate SI in the dFMR1B55 mutants using the novel Drosophila Shallow Chamber and a Python data processing pipeline based on social network analysis (SNA). In comparison with wild-type flies (w1118), SNA analysis in dFMR1B55 mutants revealed hypoactivity, fewer connections in their networks, a lower ability to efficiently transmit information, fewer alternative pathways for information transmission, a higher variability in the number of interactions they achieved, and tended to stay near the boundaries of the testing chamber. These observed alterations indicate the presence of characteristic strain-dependent social networks in dFMR1B55 flies, commonly referred to as the group phenotype. Finally, a combination of novel research tools is a valuable method for SI research in fruit flies.

Advances in biological sciences have been applied in medicine, agriculture and industry with great benefit. Some recent trends in society, governance structures and communications, however, appear to be hampering the use of new scientific findings for controlling infectious diseases. These limitations are illustrated with examples related to (i) the adaptation of fresh water mosquito vectors of major arboviral diseases to salinity in coastal areas with consequences for disease transmission, (ii) understanding the implications of reduced dengue transmission during the COVID-19 lockdown for dengue control, (iii) causes underlying the rapid spread of the malaria vector Anopheles stephensi in South Asia and Africa, (iv) the application of serodiagnostic techniques for Lyme disease and tick-borne relapsing fever caused by tick-borne bacteria of the genus Borrelia, and (v) COVID-19 prevention.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

Groundwater contamination is an ever-growing environmental issue that has attracted much and undiminished attention for the past half century. Groundwater contamination may originate from both anthropogenic (e.g., hydrocarbons) and natural compounds (e.g., nitrate and arsenic); to tackle the removal of these contaminants, different technologies have been developed and implemented. Recently, bioelectrochemical systems (BES) have emerged as a potential treatment for groundwater contamination, with reported in situ applications that showed promising results. Nitrate and hydrocarbons (toluene, phenanthrene, benzene, BTEX and light PAHs) have been successfully removed, due to the interaction of microbial metabolism with poised electrodes, in addition to physical migration due to the electric field generated in a BES. The selection of proper BESs relies on several factors and problems, such as the complexity of groundwater and subsoil environment, scale-up issues, and energy requirements that need to be accounted for. Modeling efforts could help predict case scenarios and select a proper design and approach, while BES-based biosensing could help monitoring remediation processes. In this review, we critically analyze in situ BES applications for groundwater remediation, focusing in particular on different proposed setups, and we identify and discuss the existing research gaps in the field.

With the progress of immunotherapy in cancer, oncolytic viruses (OVs) are getting more and more attention during the past decade. Due to their cancer-selective and immunogenic property, OVs are considered ideal candidates to be combined with immunotherapy to increase both specificity and efficacy in cancer treatment. OVs preferentially replicate in and lyse cancer cells, generating pathogen-associated molecular patterns (PAMPs) and danger (damage)-associated molecular patterns (DAMPs). These signals trigger innate immune response to modulate the solid tumor microenvironment, resulting in in situ autovaccination leading to adaptive anti-virus and anti-tumor immunity. Here, we summarize the conceptual updates of oncolytic virotherapy, immunotherapy, and the strategies to enhance the virus-mediated anti-tumor immune response, including: 1. Arm OVs with cytokines to modulated innate and adaptive immunity; 2. Combine OVs with immune checkpoint inhibitors to release T cell inhibition; 3. Combine OVs with immune co-stimulators to enhance T cell activation.

Surfactants are widely used in the synthesis of nanoparticles, as they have a remarkable ability to direct their growth to obtain well-defined shapes and sizes. However, their post-synthesis removal is a challenge, and the methods used often result in morphological changes that defeat the purpose of the initial controlled growth. The cleaning methods could be classified as thermal or non-thermal. In general, the structure of materials can be better preserved by non-thermal treatments. After the removal of surfactants, the highly active surfaces of nanomaterials may undergo structural reconstruction by exposure to a different environment. Thus, ex situ characterization after air exposure may not reflect the effect of the cleaning methods. In situ characterization is required to better understand the impact of various cleaning procedures. Combining X-ray photoelectron spectroscopy, in situ infrared reflection absorption spectroscopy, and environmental transmission electron microscopy measurements with CO probe experiments, we investigated different surfactant-removal methods to produce clean metallic Pt nanoparticles from surfactant-encapsulated ones. Non-thermal plasmas show the best results. It was demonstrated that both UV-ozone treatment and room temperature O2 plasma treatment lead to the formation of Pt oxides on the surface after the removal of the surfactant. These oxides are reduced to metallic Pt during in situ CO probe experiments. On the other hand, when H2 was used for plasma treatment, the Pt0 oxidation state and nanoparticle size distribution were preserved. In addition, H2 plasma treatment can reduce Pt oxides after O2-based treatments, resulting in metallic nanoparticles with clean surfaces. Thermal reduction in hydrogen leads to carbon species emerging onto nanoparticle surfaces after heating and agglomeration of Pt nanoparticles. Particularly, O2-based thermal treatments result in the formation of aggregates consisting of small nanoparticles. These findings provide a better understanding of the various options for surfactant removal from metal nanoparticles and point toward non-thermal plasmas as the best route if the integrity of the nanoparticle needs to be preserved.

Wild-type p53 cancer therapy-induced senescent cells frequently engulf and degrade neighboring ones inside a massive vacuole in their cytoplasm. After clearance of the internalized cell, the vacuole persists, seemingly empty, for several hours. Despite large vacuoles being associated with cell death, this process is known to confer a survival advantage to cancer engulfing cells, leading to therapy resistance and tumor relapse. Previous attempts to resolve the vacuolar structure and visualize their content using dyes were unsatisfying for lack of known targets and ineffective dye penetration and/or retain. Here, we overcame this problem by applying optical diffraction tomography and Raman spectroscopy to MCF7 doxorubicin-induced engulfing cells. We demonstrated a real ability of cell tomography and Raman to phenotype complex microstructures, such as cell-in-cells and vacuoles, and detect chemical species in extremely low concentrations within live cells in a completely label-free fashion. We show that vacuoles had a density indistinguishable to the medium, but were not empty, instead contained diluted cell-derived macromolecules, and we could discern vacuoles from medium and cells using their Raman fingerprint. Our approach is useful for the non-invasive investigation of senescent engulfing (and other peculiar) cells in unperturbed conditions, crucial for a better understanding of complex biological processes.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

In this communication, we present a new simulated in situ lab/on-deck incubator, light spectrum replicator (LSR), and method to simulate the measured in situ HOCR light spectrum curves in incubation chambers. Carbon flux studies require detailed knowledge of primary and secondary production, including an understanding of temporal and spatial scales of variation. Interpretation of the processes involved during measurements continues to be difficult [1] since the incubation of the samples does not permit the study of rapid variations in carbon assimilation. Further, the significance of Dissolved Organic Matter of DOM in primary production is gaining attention as many autotrophic species are known for using organic substrates for growth, even in the dark [2–4] and since a significant portion of DOM can be accounted for from active release of intracellular metabolites by microbial consortia [5]. On the other hand, the major uncertainties in bacterial production measurements lie with the conversion factors used to calculate bacterial production (BP). For a given thymidine incorporation rate, estimates of BP can range by a factor of more than 20 [6,7]. Even though various new analytical tools have emerged [8], understanding of complex patterns of interactions within the microbial loop remains an open question.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

This paper discusses how mathematical models are used to predict environmental conditions. While these models are successful for larger scale phenomena, it becomes more complex for local weather or wave processes. Several approaches have been proposed to address this problem, including neural networks and statistical and mathematical models. The novelty in this approach is the use of statistical manifolds, which provide a more accurate way to estimate distances and cost functions. This work focuses on advancements in differential and information geometry for creating different types of models that can be used for environmental simulation and forecasting. These fields are vital for many institutes and centres worldwide, as they help solve challenges in areas such as meteorology, renewable energy, and aviation safety. Some potential IG applications to advance energy were given. Closing remarks with new open problems combined with the next research phase are provided.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Powder and SLM additively manufactured parts of X5CrNiCuNb17-4 maraging steel were systematically investigated by electron microscopy to understand the relationship between the properties of the powder grains and the microstructure of the printed parts. We prove that satellites, irregularities and superficial oxidation of powder particles can be transformed into an advantage through the formation of nanoscale (AlMnSiTiCr)-oxides in the matrix during the printing process. The nano-oxides showed extensive stability in terms of size, spherical morphology, chemical composition and crystallographic disorder upon in situ heating up to 950°C in the scanning transmission electron microscope. Their presence thus indicates a potential for oxide-dispersive strengthening of this steel, which may be beneficial for creep resistance at elevated temperatures. The nucleation of copper clusters and their evolution into nanoparticles as well as the precipitation of Ni and Cr particles upon in situ heating have as well been systematically documented.

This work focuses on the study of the microstructure, hardening and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases were originated from reactions between the matrix and boron particles added in the starting mixtures of the composites. Not only was the composite composition studied as an influencing factor in the behaviour of the composites, but also different operational temperatures. Three volume percentages of boron content were tested (0.9, 2.5 and 5 vol % of amorphous boron). The manufacturing process used to produce the composites was inductive hot pressing, which operational temperatures were between 1000 °C to 1300 °C. Specimens showed optimal densification. Moreover, microstructural study revealed the formation of TiB in various shapes and proportions. Mechanical testing confirmed that the secondary phases had a positive influence on the properties of the composites. In general, adding boron particles increased the hardness and stiffness of the composites; however rising temperatures resulted in greater increases in stiffness than in hardness.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

New approaches to collect in-situ data are needed to complement the high spatial (10~m) and temporal (5-day) resolution of Copernicus Sentinel satellite observations. Making sense of Sentinel observations requires high quality and timely in-situ data for training and validation. Classical ground truth collection is expensive, lacks scale, fails to exploit opportunities for automation, and is prone to sampling error. Here we evaluate the potential contribution of opportunistically exploiting crowd-sourced street-level imagery to collect massive high-quality in-situ data in the context of crop monitoring. This study assesses this potential by answering two questions: 1) what is the spatial availability of these images across the European Union (EU)? and 2) can these images be transformed to useful data? To answer the first question, we evaluated the EU availability of street-level images on Mapillary - the largest open-access platform for such images - against the Land Use and land Cover Area frame Survey (LUCAS) 2018, a systematic surveyed sampling of 337031 points. For 37.78% of the LUCAS points a crowd-sourced image is available within a 2-km buffer, with a mean distance of 816.11 m. We estimate that 9.44% of the EU territory has a crowd-sourced image within 300-m from a LUCAS point, illustrating the huge potential of crowd-sourcing as a complementary sampling tool. After artificial and built up (63.14%), and inland water (43.67%) land cover classes, arable land has the highest availability at 40.78%. To answer the second question, we focus on identifying crops at parcel level using all 13.6 million Mapillary images collected in the Netherlands. Only 1.9% of the contributors generated 75.15% of the images. A procedure was developed to select and harvest the pictures potentially best suited to identify crops using the geometries of 785710 Dutch parcels and the pictures' meta-data such as camera orientation and focal length. Availability of crowd-sourced imagery looking at parcels was assessed for 8 different crop groups with the 2017 parcel level declarations. Parcel revisits during the growing season allowed to track crop growth. Examples illustrate the capacity to recognize crops and their phenological development on crowd-sourced street-level imagery. Consecutive images taken during the same capture track allow selecting the image with the best unobstructed view. In the future, dedicated crop capture tasks can improve image quality and expand coverage in rural areas.

A dataset collected from Central-South Finland is used to investigate the mortality of boreal trees. The mortality rate is found to be the order of three times that predicted by earlier Nordic mortality models, being in the upper range of international literature observations. Small subpopulations of any tree species tend to die out. Mortality of downy birch increases with stand basal area, as well as with stand age. Mortality of Norway spruce and silver birch increases after 100 years, while that of Scots pine is invariant to age. As the relative loss rate of basal area is insensitive to stand basal area, the mortality of trees does not strongly regulate thinning practices.

Recent developments in mid-infrared (MIR) spectroscopic ellipsometry enabled by quantum cascade lasers (QCLs) resulted in a drastic improvement in signal-to-noise ratio compared to conventional thermal emitter based instrumentation. Thus, it was possible to reduce the acquisition time for high-resolution broadband ellipsometric spectra from multiple hours to less than 1 second. This opens up new possibilities for real-time in-situ ellipsometry in polymer processing. To highlight these evolving capabilities we demonstrate the benefits of a QCL based MIR ellipsometer by investigating single and multilayered polymer films. The molecular structure and reorientation of a 2.5m thin biaxially oriented polyethylene terephtalate film is monitored during a stretching process lasting 24.5 s to illustrate the perspective of ellipsometric measurements in dynamic processes. In addition, a polyethylene/ethylene vinyl alcohol/polyethylene multilayer film is investigated at continuously varying angle of incidence ( 0∘ – 50∘) in 17.2 s, highlighting an unprecedented sample throughput for the technique of varying angle spectroscopic ellipsometry in the MIR spectral range. The obtained results underline the superior spectral and temporal resolution of QCL ellipsometry and qualify this technique as suitable method for advanced in-situ monitoring in polymer processing.

In recent years, humanity has faced a growing challenge posed by the rise of antibiotic-resistant bacteria, resulting in an alarming surge in fatalities and the emergence of increasingly hard-to-manage diseases. Among these resilient pathogens is Acinetobacter baumannii, due to its escalating prevalence in hospitals, elevated mortality rates, and resistance to treatment. Despite its clinical significance, our understanding of this pathogen in non-hospital settings and its virulence factors remains limited. Therefore, this review aims to shed light on the latest research regarding its ecological niche, microbiological traits, and antibiotic resistance profiles. Recent investigations have expanded its detection to various environmental niches, including rivers, treatment plants, and soils. Moreover, this bacterium has been discovered in diverse food sources such as meat and vegetables, as well as in farm animals and household pets like dogs and cats. This broader presence of Acinetobacter baumannii outside of hospital environments underscores a significant risk of environmental contamination, necessitating heightened awareness and preventive measures to address potential public health implications.

Green spaces localized in cities create favourable environmental conditions for Ixodes ricinus, the most widespread and important vector of tick-borne pathogens in Central Europe. In this study, we described the prevalence of Borrelia burgdorferi s.l. and Babesia species found in mono- and double infections among I. ricinus ticks occurring in urban areas of the city of Poznań, west-central Poland. Two tick groups were examined: (i) a group of 1,029 host-seeking ticks (460 nymphs, 289 females, and 280 males and (ii) a group of 1,268 engorged female ticks removed from 1,115 tick-infested animals, dogs and cats. The overall prevalence of B. burgdorferi s.l. found in host-seeking ticks was almost two-fold higher in comparison to ticks derived from pets (8.7 vs. 4.7%, respectively, χ2 test, P = 0.001). Borrelia afzelii and B. garinii were the most prevalent species both in ticks from vegetation (3.7% and 3.7%, respectively) and from pets (3.7% and 0.6%, respectively). Babesia infections were slightly more common in feeding ticks compared to those from vegetation (6.0 vs. 4.7%, respectively), however, the difference was not significant. Three Babesia species including Ba. microti, Ba. venatorum and Ba. canis were identified. Babesia canis and Ba. microti were the most prevalent in host-seeking (2.6% and 1.4%, respectively) and feeding ticks (2.8% and 2.2%, respectively), whereas Ba. venatorum was the rarest piroplasm. All Ba microti obtained sequences (n=42) were identical to Ba. microti genotype "Jena/Germany" that is considered as pathogenic to humans. Furthermore, the sequences of Ba. venatorum (n=17) were identical with those isolated from patients in Italy, Austria and Poland. Altogether, out of 121 Babesia-positive ticks, 19.8% were simultaneously infected with B. burgdorferi s.l. spirochetes. We found similar prevalences of co-infections in host-seeking (1.1%) as well as in feeding ticks (1.0%). In the first group, Ba. canis prevailed in coinfections (73%), mostly with B. afzelii and B. garinii, in the second group, Babesia microti dominated with B. afzelii (92.7%). This is the first finding documenting the co-occurrence of both pathogens in ticks from companion animals. The detection of Ba. microti and Ba. venatorum sequences identical to strains pathogenic to humans as well as predominance of LB spirochetes, B. afzelii and B. garinii in I. ricinus from vegetation and animals indicates that there is a potential risk of acquiring human babesiosis and/or Lyme borreliosis in urban areas of the city of Poznań. Although, the overall risk of encountering a Ba. microti and B. burgdorferi s.l. co-infected tick was low (1.0%), the potential for more severe clinical symptoms and complications deserves notice. A relatively high infection rates of Ba. canis in dog-derived ticks (3.2%) and in host-seeking ticks (2.6%), suggests that I. ricinus could potentially be involved in the circulation of this piroplasm in areas, where the competent vector, Dermacentor reticulatus is absent or rare.

3D-printed aluminium alloy fabrications made by selective laser melting (SLM) offer a promising route for the production of small series of custom-designed heat exchangers with complex geometry and shape and miniature size. Alloy composition and printing parameters need to be optimized to mitigate fabrication defects (pores and microcracks) and enhance the part performance. The deformation response needs to be studied with adequate characterization techniques at relevant dimensional scale capturing the peculiarities of micro-mechanical behavior relevant to the particular article and specimen dimensions. Purposefully designed Al-Si-Mg 3D-printable RS-333 alloy was investigated with a number of microscopy techniques including in situ mechanical testing with a Deben Microtest 1 kN stage integrated and synchronized with Tescan Vega3 SEM to acquire high resolution image datasets for Digital Image Correlation (DIC) analysis. Dog bone specimens were 3D-printed in different orientation of gauge zone cross-section with respect to the fast laser beam scanning and growth directions. This corresponds to varying local conditions of metal solidification and cooling. Specimens show variation in mechanical properties, namely, Young’s modulus (65…78 GPa), yield stress (80–150 MPa), ultimate tensile strength (115–225 MPa) and elongation at break (0,75–1,4 %). Furthermore, the failure localization and character was altered with the change of gauge cross-section orientation. DIC analysis allowed correct strain evaluation that overcame the load frame compliance effect and helped to identify the unevenness of deformation distribution (plasticity waves) that ultimately resulted in exceptionally high strain localization near the ultimate failure crack position.

Immunotherapy with stereotactic body radiotherapy (SBRT), low-dose antiangiogenics, immune adjuvants, nanomedicine, or other combinations will likely play a lead role in managing malignancies soon. Presently, its benefit extends to about 12% to 20% of patients, in the background of possible recurrence eventually and the toxicities, including in non-responders. Stereotactic body radiotherapy (SBRT) not only eliminates the indexed lesions, but recently, the evidence is accumulating about its systemic abscopal effects. It needs to be evolved to a dependable in situ therapeutic vaccine production and to activate short- and long-term memory immune lymphocytes. The in-situ immune cascade happens with the ability of SBRT to generate Tumor-specific neoantigens and neoepitopes, which enhance the activation of antigen-presenting cells, invoke and restore the competence of Tumor-infiltrating lymphocytes, resulting in cancer cell lysis. This cell lysis, in turn, can generate further neoantigens and epitopes, imparting a virtuous cycle that is the hallmark of effective vaccines. Additionally, SBRT can synergistically enhance the other in situ vaccination strategies, concurrent in vitro vaccines or nanomedicines, making it a primary tool for sensitizing even the “cold” tumors for immunotherapy. The present proposed hypotheses, primarily based on a preclinical literature review, focus on the critical aspects of the in-situ vaccination generation capability of SBRT when used in pulsed, cyclical, or intermittent endothelial-sparing single dose schedules along with immunotherapy and other supportive measures. This schedule is categorized as in situ vaccine dose (ISVD) radiotherapy (RT) (distinguishable from the standard therapeutic SBRT schedule) in metastatic cancer settings after standard /first-line therapies.

Accurate determination of protein localization, levels, or protein-protein interactions is pivotal for the study of their function, and in situ protein labeling via homologous recombination has emerged as a critical tool in many organisms. While this approach has been refined in various model fungi, the study of protein function in most plant pathogens has predominantly relied on ex-situ or overexpression manipulations. To dissect the molecular mechanisms of development and infection for Verticillium dahliae, a formidable plant pathogen responsible for vascular wilt diseases, we have established a robust, homologous recombination-based in situ protein labeling strategy in this organism. Utilizing Agrobacterium tumefaciens-mediated transformation (ATMT), this methodology facilitates the precise tagging of specific proteins at their C-termini with epitopes, such as GFP and Flag, within the native context of V. dahliae. We demonstrate the efficacy of our approach through the in situ labeling of VdCf2 and VdDMM2, followed by subsequent confirmation via subcellular localization and protein-level analyses. Our findings confirm the applicability of homologous recombination for in situ protein labeling in V. dahliae and suggest its potential utility across a broad spectrum of filamentous fungi. This labeling method stands to significantly advance the field of functional genomics in plant pathogenic fungi, offering a versatile and powerful tool for the elucidation of protein function.

The fate of critically sick patients with infections in intensive care units (ICUs) is significantly influenced by antimicrobial resistance, which has become a serious concern in developing nations. This observational study was conducted at the IBN Sina Specialised Hospital in Dhaka, Bangladesh, over a 12-month period from January 2021 to December 2021, in order to track the pattern of antibiotic resistance among the patients admitted to the intensive care unit (ICU). Aspiration pneumonia (29%) and diabetes mellitus (24%), among 200 patients, were the most common main diagnoses. 65 samples (or 26%) of the 250 samples had 85 bacteria identified from them. Urine (14.12%) and tracheal aspirate (64.71%) were the most frequently found sites of infection. In the sample from the tracheal aspirate, Pseudomonas spp. (30.59%), Escherichia coli (24.71%), Acinetobacter spp. (20%), and Klebsiella spp. (14.12) were the most frequently isolated microorganisms. The following antibiotics were shown to have the highest overall patterns of resistance: levofloxacin (68.24), amikacin (64.71), meropenem (49.41), ceftazidime (75.29), ciprofloxacin (78.82), and gentamicin (82.35). The most effective antibiotic against Klebsiella species was meropenem (64.61%), while Acinetobacter species were mostly susceptible to cotrimoxazole (64.67%) and piperacillin + tazobactam (60.50%). Most susceptible to netilmicin (70.48%) and meropenem (49.32%) were Escherichia coli, while Pseudomonas spp. were mostly responsive to colistin (55.14%) and netilmicin (52.25%). Antibiotic resistance is common among intensive care unit (ICU) patients, and most isolated microbes have resistance to traditional medicines.

A three-year survey was conducted to estimate the incidence of grapevine trunk diseases (GTDs) in Greece and identify fungi associated with the disease complex. In total, 310 vineyards in different geographical regions in northern, central, and southern Greece were surveyed, and 533 fungal strains were isolated from diseased vines. Morphological, physiological and molecular (5.8S rRNA gene-ITS sequencing) analyses revealed that isolates belonged to 35 distinct fungal genera, including well-known (e.g. Botryosphaeria sp, Diaporthe spp., Eutypa sp., Diplodia sp., Fomitiporia sp., Phaeoacremonium spp., Phaeomoniella sp.) and lesser-known (e.g. Neosetophoma sp., Seimatosporium sp., Didymosphaeria sp., Kalmusia sp.) grapevine wood inhabitants. GTDs-inducing population structure differed significantly among the discrete geographical zones. Phaeomoniella chlamydospora (26.62%, n=70), Diaporthe spp. (18.25%, n=48) and F. mediterranea (10.27%, n=27) were the most prevalent in Heraklion, whereas D. seriata, Alternaria spp., P. chlamydospora and Fusarium spp. were predominant in Nemea (central Greece). In Amyntaio and Kavala (northern Greece), D. seriata was the most frequently isolated species (>50% frequency). Multi-genes (rDNA-ITS, LSU, tef1-α, tub2, act) sequencing of selected isolates, followed by pathogenicity tests revealed that Neosetophoma italica, Seimatosporium vitis, Didymosphaeria variabile and Kalmusia variispora caused wood infection with the former being the most virulent. To the best of our knowledge, this is the first report of N. italica associated with GTDs worldwide. This is also the first record of K. variispora, S. vitis and D. variabile associated with wood infection of grapevine in Greece. The potential associations of disease indices with vine age, cultivar, GTD-associated population structure and the prevailed meteorological conditions in different viticultural zones in Greece are presented and discussed.

This research explores the predictive capabilities of autonomous driving systems by integrating human factor considerations within the context of safety-critical events. Recognizing the significance of human behaviors in influencing driving dynamics, the study employs advanced modeling techniques to enhance the accuracy of predictions in scenarios that demand heightened safety measures. Traditional rule-based systems and monotonic logic often fall short in addressing the complexities of safety-critical events. To overcome these limitations, the research proposes the application of non-monotonic logic, allowing for flexible and adaptive reasoning that accommodates exceptions and context-specific information.The study emphasizes the importance of incorporating individual differences among drivers, such as risk-taking tendencies, reaction times, decision-making processes, and driving styles. By considering these human factors, the research aims to develop realistic and accurate autonomous driving models that capture the nuances of real-world driving scenarios, especially in safety-critical situations. The predictive model takes into account both internal and external factors, enabling the autonomous system to anticipate and respond effectively to unforeseen events.The primary goal is to provide autonomous vehicles with the capability to make plausible inferences, handle conflicting data, and adapt their behavior in real-time during safety-critical events. The proposed model integrates personalized cognitive agents for each driver, incorporating their unique preferences, characteristics, and needs. This personalized approach aims to optimize the safety and efficiency of autonomous driving, contributing to the ongoing evolution of intelligent transportation systems.In conclusion, this research contributes to advancing the field of autonomous driving by introducing a predictive model that leverages human factor considerations to enhance safety in safety-critical events. The incorporation of non-monotonic logic and individualized cognitive agents signifies a comprehensive approach to address the challenges associated with predicting autonomous driving behavior, paving the way for safer and more reliable autonomous vehicles in dynamic and unpredictable environments.

Aims: To report on the clinico-pathological features of a series of 12 intra-oral mucoepidermoid carcinomas showing exclusive intra-cystic growth. Methods and methods: All mucoepidermoid carcinomas diagnosed in the period 1990-2012 were retrieved, the original histological preparations were reviewed to confirm the diagnosis, and from selected cases, showing exclusive intra-cystic neoplastic component, additional sections were cut at 3 subsequent 200m intervals and stained with Hematoxylin-Eosin, PAS and Alcian Blue, to possibly identify tumor invasion of the adjacent tissues, which could have been overlooked in the original histological preparations. Also, pertinent findings collected from the clinical charts and follow-up data were analyzed. Results: We identified 14 intraoral mucoepidermoid carcinomas treated by conservative surgery and with a minimum follow up of 5 years. The neosplasm were located in the hard palate (9 cases), the soft palate (2), the cheeck (2) and the retromolar trigone (1). In all instances histological examination was revealed the presence of a single cystic space, containing clusters of columnar, intermediate, epidermoid, clear and mucous-producing cells, the latter exhibiting distinct intra-cytoplasmic mucin production, as confirmed by PAS and Alcian Blue stains. The cysts were entirely circumscribed by fibrous connective tissue and no solid areas or infiltrating tumour clusters were detected. Conservative surgical resection was performed in all cases and no recurrences or nodal metastases were observed during the follow up period. Conclusions: Mucoepidermoid carcinomas showing prominent (>20%) intra-cystic proliferation currently are considered low-grade tumours. In addition, we also unveil the possibility that mucoepidermoid carcinomas, at least in their early growth phase, may display an exclusive intra-cystic fashion and might be considered as in situ carcinomas, unable to infiltrate adjacent tissues or metastasize.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

Boswellia trees are the source of frankincense, which can be found throughout the Middle East and parts of Africa and Asia. Boswellia serrata extract has been shown to have anti-cancer, anti-inflammatory, and anti-microbial effects. Periodontitis is an oral chronic inflammatory disease that affects nearly half of the US population. We investigated the antimicrobial effects of B. serrata extract on two oral pathogens associated with periodontitis. Using the minimum inhibitory concentration and crystal violet staining methods, we demonstrated that Porphyromonas gingivalis growth and biofilm formation were impaired by treatment with B. serrata extracts. However, there were no significant effects on Fusobacterium nucleatum growth and biofilm formation. Using colony-forming units quantification and microscopy techniques, we also showed that concentrations of B. serrata that were not toxic for host cells decreased intracellular P. gingivalis infection in human gingival epithelial cells. Our results show antimicrobial activity of a natural product extracted from Boswellia trees (B. serrata) against periodontopathogens. Thus, B. serrata has the therapeutic potential for preventing and/or treating periodontal diseases. Future studies will identify molecular components of B. serrata extracts responsible for the beneficial effects.

Celtis sinensis is an adaptable species that is widely grown in southern China. In June 2022, a leaf blotch disease of C. sinensis was observed in Nanjing, Jiangsu, China. Based on morphological characterization, three isolates were identified as Alternaria species. Phylogenetic analysis of combined ITS, GAPDH, TEF1-α, RPB2 and Alt a 1 sequences identified the three isolates we obtained as Alternaria alternata and Alternaria koreana. Koch’s postulates were fulfilled in the greenhouse, and the pathogenicity of A. alternata and A. koreana was determined by leaf inoculation tests on C. sinensis seedlings. The symptoms of indoor inoculation were consistent with those in the field. A. alternata and A. koreana can grow at 15-35 °C, with an optimal growth temperature of 25 °C. The results of fungicide sensitivity experiments indicated that A. alternata and A. koreana were the most sensitive to prochloraz, which may be a useful strategy for the future prevention and control management of A. alternata and A. koreana. This study provides the first step for further research on A. alternata and A. koreana as pathogens of C. sinensis and provides a theoretical basis for future control strategies.

This study focuses on examining various approaches for Tensor Decompositions (TDs) and their potential applications in satellite imaging (SI) and deep learning (DL). The research highlights how these decompositions can contribute to the advancement of SI and DL, providing valuable insights for future utilization of TDs in research. It explores how these techniques contribute to the advancement of SI and DL methods, providing insights into their potential applications and suggesting future research directions. The study aims to enhance the use of TDs techniques to further advance research efforts in these fields. More importantly, the current investigation offers a thorough analysis of the potential advantages and reasons for employing TDs techniques in different domains, including satellite imaging and deep learning. The aim is to enhance research outcomes by utilizing TDs. The review also identifies unresolved issues and proposes future directions for further investigation in this field. Fundamentally, these proposed open problems will open new grounds to the research community to articulate, innovate, and provide more real-life applications to improve the current state of the art by delving into a wider vision for a higher-level performance of both satellite imaging (SI) and deep learning (DL). Looking at the bigger scenario, this also suggests that TDs could be potentially employed to revolutionize existing machine learning technologies as well as the current space AI industry.

Three kinds of hydrophobic groups grafted starches of maleic anhydride grafted starch (MAH-g-starch), lactic acid grafted starch (LA-g-starch), and methyl acrylate grafted starch (MA-g-starch) were prepared by in-situ solid phase polymerization. The results of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were confirmed successful grafting. The grafting ratios of MAH-g-starch, LA-g-starch and MA-g-starch were 6.50%, 12.45%, and 0.57%, respectively. Influenced by the grafting ratio, LA-g-starch had the best hydrophobic properties and the largest molecular weight, and those for MA-g-starch was the worst. The surfaces of grafted starches were covered with graft polymer, with obvious surface roughness and bond degree of MAH-g-starch and LA-g-starch. The crystalline structure of grafted starches showed some damage, with LA-g-starch exhibiting the greatest decrease in crystallinity, and less of a change for MA-g-starch. Overall, the grafting reaction improved thermoplasticity, with LA-g-starch the most improved, followed by MAH-g-starch, and then MA-g-starch.

: Poultry products in Zambia form an integral part of the human diet in many households, as they are cheap and easy to produce. The burden of poultry diseases has, however, remained a major challenge. Growing consumer demand for poultry products in Zambia has resulted in non-prudent antimicrobial use on farms, intending to prevent and treat poultry diseases for growth optimization and maximising profits. This cross-sectional study aimed to identify the different types of bacteria causing diseases in chickens in Lusaka and to detect the extended-spectrum-lactamase (ESBL)-encoding genes. We collected 215 samples from 91 diseased chickens at three post-mortem facilities and screened them for gram-negative bacteria. Of these samples, 103 tested positive for various clinically relevant Enterobacteriaceae, including Enterobacter (43/103, 41.7%), Escherichia coli (20/103, 19.4%), Salmonella (10/103, 9.7%), and Shigella (8/103, 7.8%). Other isolated bacteria included Yersinia, Morganella, Proteus, and Klebsiella, which accounted for 21.4%. E. coli, Enterobacter, Salmonella, and Shigella were subjected to antimicrobial susceptibility testing. The results revealed that E. coli, Enterobacter, and shigella were highly resistant to tetracycline, ampicillin, amoxicillin, and trimethoprim-sulfamethoxazole, while Salmonella showed complete susceptibility to all antibiotics. The observed resistance patterns correlated with antimicrobial usage estimated from sales data from a large-scale wholesale and retail company. Six (6/14, 42.9%) E. coli isolates tested positive for bla_CTX-M, whilst eight (8/14, 57.1%) Enterobacter samples tested positive for bla_TEM. Interestingly, four (4/6, 66.7%) of the E. coli isolates carrying bla_CTX-M-positive strains were also positive for bla_TEM. Sanger sequencing of the PCR products revealed that five (5/6,83.3%) of the abovementioned isolates possessed the bla_CTX-M-15 allele. The results suggest the presence of potentially pathogenic ESBL-producing Enterobacteriaceae in poultry, threatening public health. Keywords:. Enterobacteriaceae, bla_CTX-M, bla_TEM

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Spodopotera frugiperda is a worldwide invasive pest that has caused major economic damage. According to classical biological control theory, natural enemies that can control invasive pests come from the area of origin as the pests that have gone through coadaptation processes. However, the new association’s approach suggests that local natural enemies are equally capable to control invasive pests. Due to the lack of data on the association of S. frugiperda and local natural enemies, research was conducted through a rapid survey to study the population density of S. frugiperda in Yogyakarta, Indonesia and to study the diversity of parasitoid associated with S. frugiperda. The results showed the difference in S. frugiperda population and parasitism rate, with 15 parasitoid species associated with S. frugiperda. Four egg parasitoids, eight larval parasitoids, and three pupal parasitoids were found to be associated with S. frugiperda for three years after it was first discovered in Indonesia. A new association was found between S. frugiperda and three parasitoid species, consisting of two egg parasitoids (Platygasteridaesp.01 and Platygasteridaesp.02) and a larval parasitoid (Eupelmidaesp.01). A relatively new association was found between S. frugiperda and two larval parasitoids (Coccygidium sp. and Stenobracon sp.), and an existing association was found between seven species including an egg parasitoid Telenomus remus, three larval parasitoids (Cotesia sp., Microplitis sp., Campoletis sp.), and three pupal parasitoids (Brachymeria lasus, B. femorata, and Charops sp.). Telenomus remus is the most dominant parasitoid, with a higher abundance and parasitism rate. This study also reported the first findings of the association of S. frugiperda with the larval parasitoid Megaselia scalaris in Indonesia. The result suggests another method for biological control using the new association approach since local natural enemies can foster quick adaptation to invasive pests.

In drilling small holes with diameters of 1 mm or less, minute clogging and twining of chips or adhesion of the workpiece material can become factors in causing breakages of the drill bit; moreover, it can be difficult to identify the machining state. Acoustic emission (AE) sensing is a nondestructive inspection technique that measures the elastic-stress waves that are generated when a material is deformed and fractured. AE sensing permits highly sensitive measurements to be made without changing the rigidity of the experimental system, unlike force sensing of cutting resistance, etc. In the present study, attempts were made to identify the machining state and tool wear, and to predict abnormalities in small-diameter drilling by using the change in the frequency of AE signal waveforms arising from deformation and fracture. It was shown that it is possible to predict the breakage of the drill bit by detecting the high-frequency AE signals caused by adhesion. In addition, a correlation map of the AE frequency spectrum for identifying the machining state in a drilling operation is suggested.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

There is a strong anticipated future for human pluripotent stem cell-derived hepatocytes (hiPS-HEP), but so far their use has been limited due to insufficient functionality. We investigated the potential of hiPS-HEP as an in vitro model for metabolic diseases by combining transcriptomics with multiple functional assays. The transcriptomics analysis revealed that 86% of the genes were expressed at similar levels in hiPS-HEP as in human primary hepatocytes (hphep). Adult characteristics of the hiPS-HEP were confirmed by the presence of important hepatocyte features, e.g. Albumin secretion and expression of major drug metabolizing genes. Normal energy metabolism is crucial for modeling metabolic diseases, and both transcriptomics data and functional assays showed that hiPS-HEP were similar to hphep regarding uptake of glucose, LDL and fatty acids. Importantly, the inflammatory state of the hiPS-HEP was low under standard conditions, but in response to lipid accumulation and ER stress the inflammation marker TNFα was upregulated. Furthermore, hiPS-HEP could be co-cultured with primary hepatic stellate cells both in 2D and in 3D spheroids, paving the way for using these co-cultures for modeling NASH. Taken together, hiPS-HEP have the potential to serve as an in vitro model for metabolic diseases. Furthermore, differently expressed genes identified in this study can serve as targets for future improvements of the hiPS-HEP.

The alignment of nanostructures in materials such as lyotropic liquid crystals (LLCs) templated materials has the potential to signicantly improve their performances. However, accurately characterising and quantifying the alignement of such fine structures remains very challenging. In situ small angle X-ray scattering (SAXS) and molecular dynamics were employed for the first time to understand the hexagonal LLC alignment process with magnetic nanoparticles under a magnetic field. The enhanced alignment has been illustrated from the distribution of azimuthal intensity in the samples exposed to magnetic field. Molecular dynamics simulations reveal the relationship between the imposed force of the magenetic nanoparticles under magnetic field and the force transferred to the LLC cylinders which leads to the LLC alignment. The combinational study with experimental measurement and computational simulation will enable the development and control of nanostructures in novel materials for various applications.

Candida (C.) infections represent a serious health risk for people affected by inflammatory bowel disease. An important fungal virulence factor is the capacity to form biofilms on the colonized surface of the host. This research study aimed to determine the effect of C. tropicalis and C. albicans co-infection on dextran sodium sulfate (DSS)-induced colitis in mice. Colitis severity was evaluated using histology and colonoscopy. Mice were mono-inoculated with C. albicans, C. tropicalis or co-challenged with both species. Mice were administered 3% DSS to induce acute colitis. Biofilm activity was assessed using (2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl] 2H-tetrazoliumhydroxide (XTT) assay. Abundance of C. albicans in the colon tissues was assessed by immunohistochemistry. Co-challenged mice showed decreased colitis severity compared to mono-inoculated mice. The XTT assay demonstrated a marked decrease of C. albicans biofilm production in a C. albicans culture incubated with C. tropicalis supernatant. Immunohistochemical staining showed that C. albicans was more abundant in the mucosa of C. albicans mono-inoculated mice compared to the co-inoculated group. These data indicate an antagonistic microbial interaction between the two Candida species, where C. tropicalis may produce molecules capable of limiting the ability of C. albicans to adhere to the host intestinal surface leading to a reduction in biofilm formation.

Maintaining the high overall health of farmed animals is a central tenant of their well-being and care. Intense animal crowding in aquaculture promotes animal especially in the absence of straightforward methods for monitoring their health. Here, we used bacterial 16S ribosomal RNA gene sequencing to measure population dynamics occurring during P. salmonis outbreaks. Our findings revealed a complex bacterial community consisting of a previously undescribed core pathobiome. Notably, we detected Aliivibrio wodanis and Tenacibaculum dicentrarchi on the skin ulcers of salmon infected with P. salmonis, while Vibrio spp. were enriched on infected gills. The prevalence of these co-occurring networks indicates the influence that coinfection plays in P. salmonis pathogenicity.

In this review, we explore a broad-based view of technologies for supporting human activities on the Moon. Primarily, we assess the state of life support systems technology beginning with physicochemical processes, waste processing, bioregenerative methods, food production systems and the robotics and advanced biological technologies that support the latter. We observe that the Moon possesses in-situ resources but that these resources are of limited value in CELSS – indeed, CELSS technology is most mature in recycling water and oxygen, the two resources that are abundant on the Moon. This places a premium on developing CELSS that recycles other elements that are rarified on the Moon including C and N in particular but also other elements such as P, S and K which might be challenging to extract from local resources. Although we focus on closed loop ecological life support systems, we also consider related technologies that involve the application of biological organisms to bioregenerative medical technologies and bioregenerative approaches to industrial activity on the Moon as potential future developments.

In-situ observation on the austenite grain growth and martensite transformation in a developed NM500 wear-resistant steel were conducted on a Confocal Laser Scanning High-temperature Microscope (CSLM). Results indicated that the martensite nucleation did not synchronously proceed during quenching process. The selective prenucleation dominated in martensite nucleation, which dividing untransformed austenite into several regions, and resulting in the larger size of fresh martensite. Martensite can not only nucleate at parent austenite grain boundaries, but also nucleate in the preformed martensite laths and twins. Smaller constraint in the martensite growth was achieved in a larger parent austenite grain size, leading to the longer fresh martensite and secondary martensite. Besides, the transformation kinetics of martensite was accelerated in a higher quenching temperature. Moreover, the martensitic laths presented in parallel laths (0~2°) based on the pre-formed lath or distributed in triangle, parallelogram or hexagon with an angle of 60° or 120°. Interestingly, martensitic lath also traversed the unstable new parent austenitic grain boundaries. In addition, the size of austenite grains increased with the quenching temperature, and austenite grains coarsened in a short time at a higher quenching temperature of 1160 ℃. Furthermore, a large amount fine dispersed particles redissolved and ripped at 1160 ℃, resulting in the many large and visible carbonitrides.

This study aimed to assess the microbiological quality of set of fruits and vegetables sold on stalls in the streets and open markets of Dakar, the capital city of Senegal. Samples purchased in seven sites were analyzed to isolate E. coli, Salmonella spp. and Vibrio spp. Some primary samples with a positive microbiological culture were subjected to DNA extraction and subsequent metagenomic analysis. A total of 240 fresh fruit and vegetable samples were collected including lettuce (n=40), tomatoes (n=40), mango slices (n=40), onion slices (n=40), mint leaves (n=40), strawberries and grapes (respectively n=20). Of these samples, 50.83% (122/240) and 60.41% (145/240) was contaminated with Escherichia coli and Vibrio spp. respectively, while Salmonella was not isolated in any product. Levels of contamination with both E. coli (1.3 103 to 6 106 CFU/g) and Vibrio spp. (4.55 102 to 8.73 106 CFU/g) were significantly above the thresholds acceptable for human consumption. The most contaminated samples were lettuce with a prevalence of 98% (39/40) for E. coli and for Vibrio spp. followed by mint leaves with 100% (40/40) and 93% (37/40) of the samples containing for E. coli and Vibrio spp. respectively. Out of 46 samples sequenced, metagenomic analysis revealed high contamination rates for E. coli, Vibrio spp. and Salmonella spp. with 100%, 67.39% and 93.47% of prevalence respectively. On the other hand, the alpha diversity analysis shows a high bacterial diversity in lettuce and mint leaf samples while beta diversity analysis highlighted the presence of two major clusters. Our results stress the need of a surveillance system that extends this investigation to a national scale while increasing the number of sampling sites and products analyzed.

The increase in incidence of superficial fungal infections combined with the emergence of antifungal resistance represents both a global health challenge and a considerable economic burden. Recently, dermatophytes, the main culprit causing superficial fungal infections, have started to exhibit antifungal resistance. This can be observed in some of the most common species such as Trichophyton rubrum and Trichophyton mentagrophytes. Importantly, the new subspecies, known as Trichophyton indotineae, has been reported to show high resistance to terbinafine, a first-line treatment for dermatophyte infections. Compounding these issues is the realization that diagnosing the causative infectious agents requires using molecular analysis that goes beyond the conventional macroscopic and microscopic methods. These findings emphasize the importance of conducting antifungal susceptibility testing to select the appropriate antifungal necessary for successful treatment. Implementing these changes may improve clinical practices that combat resistant dermatophyte infections.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

Despite recent improvements in the methods used to eradicate and minimize mosquito populations, they still pose severe threats to human health. This study aimed to investigate the Larvicidal potentials of silver nanoparticles of Ocimum gratissimum on wild Anopheles larvae from Lagos. The plant used in this study was collected from the southeastern part of Nigeria, Ibite-Olo in Ezeagu Local Government Area of Enugu State. Wild Anopheles mosquito larvae were collected from a field at Kosofe Local Government Area of Lagos State, Nigeria where resistant Anopheline populations have been reported in and around Lagos State were brought to the laboratory and kept under standard insectary conditions (25–29 °C;78–82% relative humidity). Aqueous extract of Ocimum gratissimum was made and subsequently into the silver nanoparticles. A bioassay test was performed according to WHO guidelines, with six different concentrations to assess the larvicidal activity and values obtained were subjected to log prohibit regression analysis to obtain LC₅₀ and values with 95% confidence limit. The results of the larvicidal activities of the silver nanoparticles of Ocimum gratissimum showed that the mortality rate was dose-dependent with the percentage mortality increasing at a direct proportional rate as with dose and time of exposure. Ocimum gratissimum gave LC₅₀ at 0.5 ppm and LC₉₅ at 2.5 ppm respectively. The biosynthesized silver nanoparticles augmented the larvicidal activity of the silver nanoparticles of Ocimum gratissimum on wild Anopheles larvae from Lagos. Therefore, this study showed that the silver nanoparticles of Ocimum gratissimum have the potency to be used against an insecticide-resistant mosquito vector and are a suitable candidate for the development of novel natural insecticides.

Laser in situ keratomileusis (LASIK) is the gold standard in the surgical correction of refractive errors on the cornea. It entails the creation of a superficial hinged corneal flap by a femtosecond laser, ablation of the underlying stromal bed by an excimer laser, and reposition of the flap. The corneal flap can be build in a 2-dimension (2D) fashion with tapered edges, or in a 3-dimension (3D) fashion, with angled sidecut. The latter reduces the risk of flap dislocation and infiltration of epithelial cells. This retrospective study compares with optical coherence tomography 3D and 2D flaps, and respective intra- and early post-operative complications. Four hundred consecutive eyes were included, 200 for each group. In the 3D group, the mean edge angle was 92°. The procedure was in average 5.2 seconds slower in the 3D group (p=0). Non visually significant flap folds were found in 13 eyes of the 2D group and in 7 eyes of the 3D group (p= 0.17). An intracorneal opaque bubble layer induced by laser photodisruption was more commonly observed in the 3D group (9 eyes vs. 2; p=0.03). In conclusion, the creation of a LASIK flap by a 3D-femtosecond laser cut was safe and effective.

Ixodes scapularis is a blood-feeding obligate ectoparasite responsible for transmitting the Lyme disease (LD) agent, Borrelia burgdorferi. During the feeding process, I. scapularis injects B. burgdorferi into the host along with its saliva, facilitating the transmission and colonization of the LD agent. Tick calreticulin (CRT) is one of the earliest tick saliva proteins identified and is currently utilized as a biomarker for tick bites. Our recent findings revealed elevated levels of CRT in the saliva proteome of B. burgdorferi-infected I. scapularis nymphs compared to uninfected ticks. Differential precipitation of proteins (DiffPOP) and LC-MS/MS analyses were used to identify the interactions between Ixs (I. scapularis) CRT and human plasma proteins and further exploring its potential role in shielding B. burgdorferi from complement killing. We observed that although yeast expressed recombinant (r) IxsCRT binds to the C1 complex (C1q, C1r, and C1s), the activator of complement via the classical cascade, it did not inhibit deposition of the membrane attack complex (MAC) via the classical pathway. Intriguingly, rIxsCRT binds intermediate complement proteins (C3, C5, and C9) and reduces MAC deposition through the lectin pathway. Despite inhibition of MAC deposition in the lectin pathway, rIxsCRT did not protect a serum sensitive B. burgdorferi strain (B314/pBBE22Luc) from complement-induced killing. As B. burgdorferi establishes a local dermal infection before disseminating to secondary organs, it is noteworthy that rIxsCRT promotes the replication of B. burgdorferi in culture. We hypothesize that rIxsCRT may contribute to the transmission and/or host colonization of B. burgdorferi by acting as a decoy activator of complement and by fostering B. burgdorferi replication at the transmission site.

Chronic kidney disease (CKD) is characterized by a continuous decline in kidney function, often persisting for years or even a lifetime. This study presents a new exploration into the extraction and application of insect chitosan (Tenebrio molitor) targeting hemodialysis (HD). Initially, the potential of insect-derived chitosan as a sustainable and effective alternative to traditional sources (i.e. crustaceans) is demonstrated. Efficient extraction methods were developed (totaling between 6 h and 12 h), producing chitosan. Firstly, chitin was efficiently isolated from T. molitor through deproteinization and demineralization, with yields of approximately 5% (w/w). Subsequently, chitosan was obtained from the extracted chitin resulting in yields of between 65.0 ± 0.8% (w/w) and 79.3 ± 0.8% (w/w). Characterization using Fourier Transform Infrared Spectroscopy (FTIR) confirmed structural similarities with commercial chitosan and degrees of deacetylation in the 73 - 75% range. The bioactive properties of chitosan obtained from T. molitor, including antimicrobial and antioxidant activities, were evaluated. All the microorganisms tested were inhibited, exhibiting minimum lethal concentrations between 2 and 8 mg/mL, confirming the antimicrobial activity of the extracted chitosan. In addition, chitosan showed antioxidant activity in the range of 60 to 65 µmol Trolox equivalent/g, suggesting its viability for various medical applications.This study also developed a chitosan-based membrane (CH - M) culminating in a proof-of-concept phase for hemodialysis. The permeation characteristics of CH-M for urea and albumin were studied in vitro to assess their suitability as HD membranes. Urea was permeable to values of over 70% and albumin was retained.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

Metagenomic analysis of Aedes aegypti and Ae. albopictus mosquitoes from diverse geographical regions of India revealed presence of several insect viruses of human interest. Most abundant reads found in Ae. aegypti mosquitoes were Phasi-Charoen like virus (PCLV), Choristoneura fumiferana granulovirus (CfGV), Cell fusing agent virus (CFAV) and Wenzhou sobemo-like virus 4 (WSLV4), whereas WSLV4 and CfGV constituted the highest percentage in Ae. albopictus viromes. Other reads which were of low percentage included Hubei mosquito virus 2, Porcine astrovirus 4 and Wild Boar astrovirus. PCLV and CFAV, which were found to be abundant in Ae. aegypti viromes, were absent in Ae. albopictus viromes. Among the viromes analyzed, Ae. aegypti sampled from Pune showed highest percentage (79.82%) of viral reads while Ae. aegypti mosquitoes sampled from Dibrugarh showed lowest percentage (3.47%). Shamonda orthobunyavirus, African swine fever virus, Aroa virus and Ilheus virus, having potential to infect vertebrates including humans, were also detected in both mosquito species, albeit in low read numbers. Reads of gemykibivirus, avian retrovirus, bacteriophages, herpesviruses and viruses infecting protozoans, algae, etc. were also detected in the mosquitoes. A high percentage of reads in the Ae. albopictus mosquito samples remained unclassified and warrant further investigation. Data generated in the present work may not only lead to studies to explain the influence of these viruses on replication and transmission of viruses of clinical importance but also find application as biocontrol agents against pathogenic viruses.

The predatory mirids Macrolophus pygmaeus Ramber and Nesidiocoris tenuis Reuter (Heteroptera: Miridae) are used for the biological control of Tuta absoluta Meyrick (Lep.: Gelechiidae) and other pests in tomato greenhouses. The functional response of 1 (young) and 10 (old) days old adult females and males of M. pygmaeus and N. tenuis on eggs of T. absoluta, was determined on tomato at two temperatures (20° and 25°C) and LD 16:8 and found to be Type II. M. pygmaeus females exhibited higher predation efficiency, than males at both tested temperatures. Young M. pygmaeus females had a higher efficiency than old ones, whereas males had a low efficiency irrespective of age. The predation efficiency of N. tenuis was high (but lower than M. pygmaeus) in both young females and males, although old females had a higher efficiency than the respective males. Our results show that the two predatory species have different functional response characteristics to their prey depending mainly on sex and age which may affect their role as biological control agents.

Burkholderia are a group of Gram-negative bacteria that can cause a variety of diseases in at-risk populations. B. pseudomallei and B. mallei, the etiological agents of melioidosis and glanders, respectively, are the two clinically relevant members of the B. pseudomallei complex (Bpc). The development of vaccines against Bpc species has been accelerated in recent years, resulting in numerous promising subunits and glycoconjugate vaccines incorporating a variety of antigens. However, a second group of pathogenic Burkholderia species exists known as the Burkholderia cepacia complex (Bcc), a group of opportunistic bacteria which tend to affect individuals with weakened immunity or cystic fibrosis. To date there have been few attempts to develop vaccines to Bcc species. Therefore, the primary goal of this review is to provide a broad overview of the various subunit antigens that have been tested in Bpc species, their protective efficacy, study limitations, and known or suspected mechanisms of protection. Then, we assess the reviewed Bpc antigens for their amino acid sequence conservation to homologous proteins found in Bcc species. We propose that protective Bpc antigens with a high degree of Bpc-to-Bcc sequence conservation could serve as components of a pan-Burkholderia vaccine capable of protecting against both disease-causing groups.

The chemical reaction of ion-adsorption type rare earth during in-situ leaching process is accompanied by ion migration and charge movement, making the leaching process electrochemical in nature. The chemical reaction rate plays an important role in the leaching rate of rare earth elements. In this work, electrochemical impedance spectroscopy (EIS) was used to reveal characteristics of electrical resistance alteration and leaching rate of rare earth elements during in-situ leaching. The equivalent circuit model of the leaching process was established, and two critical parameters of solution resistance Rs and charge transfer resistance Rt were analyzed to reflect the electrochemical characteristics. According to the characteristics of electrical resistance alteration, the leaching process was divided into four stages: wetting, reaction, equilibrium, and top water stage. The resistance parameters Rs and Rt decreased first and then increased during the leaching process. The maximum value of Rs was 1330Ω∙cm2 at the end of the top water stage, and the minimum value was 135Ω∙cm2 at the beginning of the equilibrium stage. The maximum value of Rt was 8310Ω∙cm2 at the beginning of the leaching stage, and the minimum value was 21Ω∙cm2 at the end of the reaction stage. Rs and Rt were negatively correlated with the pore size and chemical reaction rate during leaching. With increasing of pore size and reaction rate , the resistance parameter decrease. This study provide a new idea for intelligent monitoring of rare earth ore.

The (Ti, Nb)(C, B)/IN625 composite coating with both homogeneous and defect-free microstructure were successfully prepared by in situ on the surface of 42CrMo steel using the coupling of the ultra-high-speed laser cladding (EHLA in German) technology with the direct reaction synthesis (DRS) technology, and were comparatively analyzed with the IN625 coating prepared by the EHLA. The microstructure of the fused cladding layer was investigated by selected scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and double spherical aberration transmission electron microscopy (DSA-TEM). The residual stress distribution on both sides of the fused cladding interface was characterised by nanoindentation stress test based on the modified O&P method and the G&S energy method. The results show that the interface of (Ti, Nb)(C, B)/IN625 composite coatings is affected by about 670 kJ Joule heat released from the in-situ reaction, and the interfacial width reaches 24 μm, so that it is 6 times higher than that of IN625 coating prepared by EHLA, which effectively reduces the stress gradient in the interfacial region and alleviates the stress mismatch on both sides of the interface. However, the surface hardness of (Ti, Nb)(C, B)/IN625 composite coating is lower than that of the IN625 coating, with a value of about 240 HV0.2, and the average wear weight loss was only 10% of that of the IN625 coating, which is on the one hand attributed to the in-situ authigenic TiCB, TiC, NbMo3B4, and NbMo2B2 phases supporting the (Ti, Nb)(C, B)/IN625 composite coating substrate to achieve the abrasion reduction and wear resistance. On the other hand, it is attributed to the formation of nano-equiaxial ultrafine grains in the depth range of 250 nm below the wear surface area by the coupling of the three fields of plastic rheology-heat-force, which dynamically strengthens the wear surface.

Understanding mechanisms of ageing remains a complex challenge for biogerontologists, but recent adaptations of evolutionary ageing theories offer a compelling lens in which to view both age-related molecular and physiological deterioration. Ageing is commonly associated with a progressive loss of biochemical processes and degeneration of molecular material, however, the mechanisms of diminishing function are not simply a result of aberrant expression of these pathways. Natural selection pressures are at their highest in youthful periods to select genes advantageous to maximising reproductive capacity. After sexual maturation, selective pressure diminishes, subjecting individuals to maladaptive pleiotropic gene function once beneficial for developmental growth, but pathogenic later in life. Due to this selective ‘shadowing’ in ageing, mechanisms to counter hyperfunctional genes are unlikely to evolve within a given species. These genetic ‘run-on’ programmes are not dysfunctional per se and, in fact, remain highly robust. Thus, interventions capable of optimising gene function during the ageing process represent as attractive therapeutic modalities. Caenorhabditis elegans offers a unique model to explore high-throughput screening of interventions to combat hyperfunctional pathways involved in ageing. However, the majority of research to date employ whole-life vs late-life pathway manipulation of developmental/growth-related systems to claim ageing attenuation, despite significant impairments in early-life fitness and discordance with healthspan. Here, we discuss data supporting hyperfunctional changes at a global molecular and functional level in C. elegans, and how classical lifespan-extension mutants alter these dynamics. We later discuss the relevance of such mutant models for exploring mechanisms of ageing, highlighting that post-reproductive gene manipulation represents a far more translatable approach for C. elegans research not routed within pleiotropic constraints. More so, lifespan has become a routine readout for quantifying ‘ageing’, however, we make the argument that a compression of gerospan vs lifespan extension is a more meaningful goal for anti-ageing regimes with current knowledge. Similarly, mechanisms governing lifespan are distinct from those regulating health, and slowing senescent pathology accumulation appears more applicable for the abstraction to human ageing.

Individuals with BPD grapple with unstable relationships, marked by extreme emotional swings and interpersonal conflicts. Emotional instability, a distorted self-image, and impulsivity further complicate matters, often leading to self-harm and suicide attempts as desperate coping mechanisms. Genetics and adverse childhood experiences contribute to BPD's development, shaping brain function and emotional regulation. Diagnosis involves meticulous assessments, paving the way for personalized treatments like dialectical behavior therapy and, in severe cases, hospitalization. Early intervention, professional support, and societal understanding are pivotal for positive outcomes, and challenging mental health stigma.

The crayfish plague is a devastating disease of European freshwater crayfish and is caused by the oomycete Aphanomyces astaci (Ap. astaci), which was introduced to Europe around 1860. All European species of freshwater crayfish are susceptible to the disease, including the white-clawed crayfish Austropotamobius pallipes. The aquatic mould is primarily spread by North American crayfish species and can also disperse rapidly through contaminated wet gear moved between water bodies. This spread, coupled with competition from non-indigenous crayfish, has drastically reduced and fragmented native crayfish populations across Europe. Remarkably, the island of Ireland remained free from the crayfish plague pathogen for over 100 years, providing a refuge for A. pallipes. However, this changed in 1987 when a mass mortality event was linked to the pathogen marking the pathogen's introduction to the region. Fortunately, the plague did not establish and was not detected again in Ireland until 2015 when a molecular analysis linked a mass mortality event in the Erne catchment to Ap. astaci. Since then, the pathogen has appeared across the island. Between 2015 and 2023, Ap. astaci was detected in 18 Irish water catchments, revealing multiple genotypes. Intriguingly, the pathogen in Ireland exists without its natural host species. The uneven distribution of various genetic lineages strongly suggests human-mediated transport of zoospores via contaminated water equipment as a primary cause of spread. This review details the timeline of these events, Ap. astaci’s introductions into Ireland, its rapid spread, the genotypes documented, the issue of non-indigenous crayfish species in Ireland and management efforts.

Ureaplasma species (Ureaplasma spp.) are commonly found as commensals in the human urogenital tracts , but their overgrowth can lead to infection in the urogenital tract and at distal sites. Treatment of Ureaplasma spp. infections is difficult. The lack of a cell wall confers resistance to all β-lactam and glycopeptide antibiotics whereas the lack of de novo synthesis of folic acid makes them resistant to sulfonamides and diaminopyrimidines. Thus, there is a need to search for new drugs effective against these bacteria. In the presented studies, the effect of N,N-diethyldithiocarbamate (DDC) at a concentration of 2 µg/ml, 20 µg/ml and 200 µg/ml on the growth and survival of Ureaplasma urealyticum and Ureaplasma parvum was tested. Our results indicated that all DDC concentrations used showed both bacteriostatic and bactericidal activity against both tested strains In brief, for the first time we showed the bacteriostatic and bactericidal activity of DDC against Ureplasma urealyticum and Ureaplasma parvum. Based on literature data, we conclude that this DDC activity is related to the inhibition of urease activity, which is an indispensable enzyme for these bacteria. Further research is needed and the results obtained in the present study should be verified in in vivo models of infection.

O26 enteropathogenic Escherichia coli (EPEC), possesses a unique pseudocapsule composed of polysaccharides identical to the O antigen in their lipopolysaccharide (LPS) membrane. Therefore, the impact of O26 polysaccharides on the immune evasion mechanisms of capsulated O26 EPEC was investigated. Our findings reveal that the concentration of GlcNAc, an immunodominant unit of O26 polysaccharides capable of activating the MBL (Mannose Biding Lecting) pathway of the complement system, was found to be lower in capsulated EPEC O26 compared to naked shiga toxin-producing E. coli (STEC) O26 strain. It was noted that, unlike the naked STEC strain, the capsulated EPEC O26 strain was protected against lysis by the alternative pathway of the com-plement system by inhibiting C3b adhesion to its bacterial surface. Capsulated EPEC O26 strains were also able to avoid phagocytosis by macrophages. However, the immune evasion provided by the capsule was overcome in the presence of anti-O26 polysaccharide antibodies. Additionally, these antibodies were able to recognize O26 EPEC in the presence of biofilm and inhibit their adhesion to human epithelial cells. Overall, the results indicate that the O26 polysaccharides can generate an effective humoral immune response, making them promising antigens for the de-velopment of a vaccine against capsulated O26 E. coli

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Acid in-situ leaching (ISL) is a common approach to the recovery of uranium in the subsurface. As some toxic and harmful substances might be produced by the chemical reactions among the injected sulphuric acid, the groundwater, and the porous media during leaching processes, the pollution control of the mining plan for ISL is important. In this study, a three-dimensional reactive transport modeling (3DRTM) was applied to decide the pollution control mining plan, considering the partial penetration through wellbore in confined aquifer and complex chemical reactions between main minerals. Based on the 3DRTM, different pumping ratio and non-uniform injection schemes were compared. The results show that the preferential pollution control mining plan is non-uniform injection ratio equal 0.1. By analyzing the characteristics of water table and streamline, it is concluded that the scheme has a strong hydraulic capture effect. In this scheme, the concentration of UO22+, H+, SO42- obtained by 3DRTM is lower. The inner well injection rate is 194.09 m3/d, the outer well injection rate is 158.89 m3/d, and the pumping rate is 264.00 m3/d. A reasonable suggestion is to adopt non-uniform injection mining mode in ISL.

(1) Background: Considering highly selected patients with ductal carcinoma in situ (DCIS), active surveillance is a valid alternative to surgery. Our study is aimed at showing the reliability of post-biopsy complete lesion removal, documented by mammogram, as additional criterion to select these patients. (2) Methods: 2173 Vacuum Assisted Breast Biopsies (VABB) documented as DCIS have been reviewed. Surgery has been performed in all cases. We retrospectively collected the reports of post-VABB complete lesion removal and the histological results of the biopsy and surgery. We calculated the rate of upgrade of DCIS identified on VABB upon excision for patients with post-biopsy complete lesion removal and for those showing residual lesion. (3) Results: We observed 2173 cases of DCIS: 408 classified as low grade; 1262 as intermediate grade; 503 as high grade. The overall upgrading rate to invasive carcinoma was 15.2% (330/2173). The upgrade rate was significantly lower (8.2%) when considering patients showing mammographically documented complete removal of the lesion. (4) Conclusion: The absence of mammographically documented residual lesion following VABB is associated to a lower upgrading rate of DCIS to invasive carcinoma on surgical excision and should be considered when deciding the proper management DCIS diagnosis.

Ethanolic extracts of propolis collected from Apis mellifera hives have been shown to reduce Nosema ceranae infection in honey bee workers. This study aimed to determine the propolis concentration that optimizes the control of N. ceranae infection in honey bee workers. Newly emerged worker bees were individually fed 2 μL of 50% sucrose solution (w/v) containing 105 N. ceranae spores per bee, and treated with 0%, 25%, 50%, and 75% ethanolic extracted propolis in 50% sucrose solution (v/v). The treated bees were maintained in cages at 34 ± 2˚C and 55 ± 5% RH throughout the study. The number of dead bees was counted and removed from the cages daily for 30 days to generate survival curves. The number of N. ceranae spores per bee (infectivity) was quantified using a hemocytometer, and the number of infected bees per hundred bees (infection rate) was determined. The survival rates of N. ceranae infected bees fed 25%, 50%, and 75% propolis (NP1, NP2, NP3, respectively) were significantly higher than those of infected bees not fed propolis (NO). Furthermore, the infectivity and infection rates of NP2 and NP3 groups were significantly lower than those of the NO group. The infectivity and infection rates of the NP1 group were not different than those of the NO group. Our data suggest that 50% and 75% propolis extracts are appropriate concentrations for treating N. ceranae infection in honey bees. Ethanolic extracted propolis can be an alternative treatment for N. ceranae infection in Western honey bees.

This study developed Makgeolli (Korean traditional alcoholic beverage) by adding raw 20% Codium fragile (Cf), a green seaweed, to a mixed base consisting of rice and oats (1:1 ratio) (COM) and analyzed its quality characteristics and antioxidant activity. The rice based Makgeolli supplemented with raw 20% Cf was designated as control (CRM). The physicochemical (pH, acidity), microbiological (yeast, lactic acid bacteria), antioxidant (DPPH, ABTS), and sensory properties (7-henodonic scale) of CRM and COM were investigated during 7 days of fermentation. The pH/acidity levels of CRM and COM reached 3.66/0.68 and 3.69/0.95 after 7 days of fermentation, respectively. Compared to CRM, COM had lower alcohol and sugar contents (P < 0.05) (CRM: 14.5%/9.8 Brix, COM: 11.2%/7.4 Brix). However, COM contained more yeast and lactic acid bacteria (P < 0.05) (CRM: 1.30/4.28 log, COM: 6.04/6.09 log) compared to CRM. The antioxidant activity of DPPH/ABTS (P < 0.05) in COM was approximately 1.5 times that of CRM (CRM: 40.00/51.57%, COM: 56.76/70.91%). In addition, COM had an excellent sensory preference score (P < 0.05) due to its overall fresh flavor and savory taste (CRM: 4.93, COM: 6.06). Therefore, COM was shown to be Makgeolli with enhanced antioxidant function, with yeast and lactic acid bacteria, and improved flavor, suggesting the possibility of commercializing this Makgeolli.

This study aimed to evaluate the diagnostic roles of various immunohistochemical markers in urothelial carcinoma in situ (uCIS) through a meta-analysis and review of diagnostic test accuracy. Immunohistochemical markers CK20, CD44, AMACR, and p53 were evaluated in the present study. We analyzed the expression rates of immunohistochemical markers and compared their diagnostic accuracies. The estimated expression rates were 0.803 (95% confidence interval [CI]: 0.726–0.862), 0.142 (95% CI: 0.033–0.449), 0.824 (95% CI: 0.720–0.895), and 0.600 (95% CI: 0.510–0.683) for CK20, CD44, AMACR, and p53, respectively. In the comparison between uCIS and reactive/normal urothelium, the expression of CK20, AMACR, and p53 in uCIS was significantly higher than in reactive/normal urothelium. CD44 showed significantly lower expression in uCIS than in the reactive/normal urothelium. Among the markers, AMACR had the highest sensitivity, specificity, and diagnostic odds ratio. The AUC on SROC was the highest for CK20. In conclusion, immunohistochemical markers, such as CK20, CD44, AMACR, and p53, can be useful in differentiating uCIS from reactive/normal urothelium.

Cariogenic oral biofilms cause a considerable amount of recurrent dental caries around composite restorations every year, resulting in unprosperous oral health status and expensive restorative treatment for many patients. Quaternary ammonium monomers that can be copolymerized with the current dental resin systems have been increasingly explored for modulation of dental plaque biofilm growth over dental composite surfaces. Here, we investigated the effect of bis(2-methacryloyloxyethyl) dimethylammonium bromide (QADM), against human overlying mature oral biofilms grown intra-orally in human participants for 7 and 14 days, for the first time. Seventeen volunteers wore palatal devices containing composite specimens containing 10% by mass of QADM or a control composite without QADM. After 7 and 14 days, the adherent biofilms were collected for determination of bacterial counts via colony-forming unit (CFU) counts. The biofilm viability, chronological changes, and percentage coverage were also determined by live/dead staining. QADM composites caused a significant inhibition of S. mutans biofilm formation for up to seven days. No difference in the CFU values were found for the 14-day period. Our findings suggest that (1) QADM composite was successful in inhibiting 1-3 day biofilms in the oral environment in vivo; (2) QADM significantly reduced the portion of S.mutans group in a time course where patients at high risk of caries would develop initial enamel carious lesions; and (3) stronger antibiofilm activity is required for the control of mature long-term cariogenic biofilms. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches into clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria seem to be a promising approach in patients at high risk of recurrence of dental caries around composites.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

Euler sums are alternating (or level two) extension of multiple zeta values (MZVs). Kaneko and Tsumura initiated the study of multiple T-values (MTVs), another level two generalization, by restricting the summation indices in the definition of MZVs to a fixed parity pattern. In this paper, we shall study finite MTVs and their alternating versions which are level two and level four variations of finite MZVs, respectively. We conjecture that all finite MZVs are in the Q-span of finite MTVs which in turn apparently lie in the span of finite Euler sums, and the inclusions are both proper. We shall first provide some structural results for Euler sums of small weights, guided by the author's previous conjecture that the finite Euler sum space of weight w is isomorphic to a quotient Euler sum space of weight w. Then, by utilizing some well-known properties of the classical alternating MTVs, we shall derive a few important Q-linear relations among the finite alternating MTVs, including the reversal, linear shuffle and sum relations. We then compute the upper bound for the dimension of the Q-span of weight w finite (alternating) MTVs for w<9, both rigorously using the newly discovered relations and numerically aided by computers.

Amphibians are widely known as a prolific source of bioactive metabolites. In this work we isolated and characterized compounds with antiparasitic activity from the oocytes of the toad Rhinella alata collected in Panama. Bio-guided isolation and structural elucidation was carried out using chromatographic and spectroscopic techniques. The organic crude extract was subjected to solid phase extraction followed by HPLC purification of the fraction with in vitro activity against Trypanosoma cruzi trypomastigotes. Seven steroids (1-7) of the bufadienolide family were isolated and their structures determined using NMR and MS analyses; of these 19-formyl-dyscinobufotalin (3) is reported as a new natural product. Compounds 1, 3-7, resulted with a good anti-trypanosomal activity profile, among these 16β-hydroxyl-hellebrigenin (1) and bufalin (7) showed significant selectivity for T. cruzi. Furthermore, molecular docking analysis showed compounds 1, 3 and 7 interact through H-bonds with the amino acid residues GLN-19, ASP-158, HIS-159 and TRP-177 from cruzipain, at the catalytic site. Given the lack of therapeutic options to currently treat the American trypanosomiasis, this work can serve as the basis for further studies that aim the development of bufadienolides or their derivatives as drugs against Chagas disease.

Background: We aimed to create a model of radiological and pathological criteria able to predict the upgrade rate of low-grade ductal carcinoma in situ (DCIS) to invasive carcinoma, in patients undergoing vacuum-assisted breast biopsy (VABB) and subsequent surgical excision. Methods: 3100 VABBs were retrospectively reviewed among which we reported 295 low-grade DCIS who subsequently underwent surgery. The association between patients’ features and the upgrade rate to invasive breast cancer (IBC) was evaluated by univariate analysis. Finally, we developed a predictive multivariable model based on the features which were significantly associated with the univariate analysis outcome. Results: the upgrade rate to invasive carcinoma was 10.8 %. At univariate analysis, the risk of upgrade was significantly lower in the absence of post- biopsy residual lesion (p<0.001), age > 50 (p=0.029), and in presence of low-grade DCIS only in specimens with microcalcifications (p=0.002). According to the final multivariable model, the predicted probability of diagnostic underestimation for a patient with all the three favourable features selected at univariate analysis was 1% (95% CI: 0.3%-4%). Conclusions: An easy to use predictive model of radiological and pathological criteria is able to identify patients with low-grade carcinoma in situ with low risk of upstaging to infiltrating carcinomas.

Glucosinolates, the main secondary metabolites accumulated in cruciferous flora, have a major impact on fortifying plant immunity against diverse pathogens. Although Botrytis cinerea exhibits varying sensitivity to these compounds, current research has yet to fully understand the intricate mechanisms governing its response to glucosinolates. Different species of the genus Botrytis were exposed to glucosinolate-breakdown products revealing that B. fabae, B. deweyae and B. convoluta, species lacking the mfsG transporter gene (Bcin06g00026), were more sensitive to glucosin-olate-breakdown products than Botrytis species containing that gene such as B. cinerea, B. pseudo-cinerea and B. byssoidea. This finding was further corroborated by the inability of species lacking the mfsG gene to infect plants with a high concentration of glucosinolate breakdown products. These results challenge established correlations, revealing varying aggressiveness on different plant substrates. Expression analysis highlighted the gene's induction in the presence of isothiocyanate, and bioinformatic investigation identified homologous genes in other Botrytis species. Our study underscored the importance of advanced biotechnology to help understand these proteins and thus offer innovative solutions for agriculture

Leishmania infantum is an hemopathogen of importance for the health of domestic dogs (Canis lupus familiaris), causing canine leishmaniasis (CanL), as well as it is the etiological agent of human visceral leishmaniasis (HVL). This parasite was not reported in southern Brazil until the early 2000s, but CanL and HVL were increasingly reported in the last 15 years, mainly in cities bordering Argentina. The present study aimed to detect L. infantum in urban dogs and to determine the main clinical manifestations in the infected animals from Uruguaiana, a city with a high incidence of CanL. Fifty-one dogs suspected of having CanL in the urban perimeter of the city were clinically examined by veterinarians and investigated for the occurrence of L. infantum with two immunoassays (rapid chromatography test and ELISA) and real-time PCR. Clinical signs were compared in positive and negative L. infantum animals. A total of 31 dogs (60.8%) were infected with L. infantum. The main clinical manifestations associated to CanL dogs were onychogryphosis and peeling (p&lt;0.05). L. infantum was frequently detected in urban dogs from Uruguaiana, highlighting the health concerning situation in this city. The occurrence of some clinical signs (onychogryphosis/peeling) could help to detect more frequently CanL in the canine population.

A new quinazolinone alkaloid, named peniquinazolinone A (1), as well as eleven known com-pounds, 2-(2-hydroxy-3-phenylpropionamido)-N-methylbenzamide (2), viridicatin (3), viridicatol (4), (±)-cyclopeptin (5a/5b), dehydrocyclopeptin (6), cyclopenin (7), cyclopenol (8), methyl-indole-3-carboxylate (9), 2,5-dihydroxyphenyl acetate (10), methyl m-hydroxyphenylacetate (11), conidiogenone B (12), was isolated from the endophytic Penicillium sp. HJT-A-6. The chemical structures of all compounds were elucidated by comprehensive spectroscopic analysis, including 1D, 2D NMR, and HRESIMS. The absolute configuration at C-13 of peniquinazolinone A (1) was established by applying the modified Mosher’s method. Compounds 2, 3, and 7 exhibited an op-timal promoting effect on the seed germination of Rhodiola tibetica at a concentration of 0.01 mg/mL, while the optimal concentration for compounds 4 and 9 to promote Rhodiola tibetica seed germination was 0.001 mg/mL. Compound 12 showed optimal seed-germination-promoting activity at a concentration of 0.1 mg/mL. Compared with the positive drug 6-benzyladenine (6-BA), compounds 2, 3, 4, 7, 9, and 12 could extend the seed-germination period of Rhodiola tibetica up to the 11th day.

Investigation of oomycete diversity in rice paddies of Fars Province in Iran led to the identification of two new Pythium sensu lato (s.l.) species as Globisporangium izadpanahii sp. nov. and Pythium banihashemianum sp. nov. The identification was based on morphological and physiological features as well as the phylogenetic analysis of nuclear (ITS and βtub) and mitochondrial (cox1 and cox2) loci using Bayesian inference and Maximum Likelihood. A major characteristic of G. izadpanahii was the production of globose hyphal swellings; this species did not produce vesicles and zoospores. The present paper describes formally these two new species and defines their phylogenetic relationships with other congeneric species. According to multiple gene genealogy analysis, G. izadpanahii grouped with other species of Globisporangium in the former clade G of Pythium s.l. and was closely related to both G. nagaii and the recently described G. coniferarum. The second species, designated P. banihashemianum, grouped with other species of Pythium sensu stricto in the former clade B of Pythium s.l. and according to the phylogenetic analysis shared an ancestor with P. plurisporium. In pathogenicity tests on rice seedlings, P. banihashemianum isolates were highly pathogenic causing severe root and crown rot, while G. izadpanahii isolates were not pathogenic.

Pollutants accumulate in aquatic habitats as a result of mining activities. Lemna gibba and Lemna minor were used in this study to examine the accumulation capacities of Mo+, Pb+, and Cu++ in the acid fluids of the copper mining. Duckweed family includes water plants like L. minor and L. gibba. These are tiny, delicate, free-floating aquatic plants. Two reactors were assigned to L. gibba and L. minor, respectively. Throughout the course of eight days, these plants and reactor water were gathered every day. The acid mine water's pH, temperature, and electric conductivity were also tested every day. The L. gibba and L. minor were cleaned, dehydrated, and burned in a drying oven for a whole day at 300 oC. ICP-MS (Inductively Coupled Plasma Mass Spectroscopy) was used to determine the Mo+, Pb+, and Cu++ content of the plant and water samples. The concentrations of Mo, Pb, and Cu in the acid mine fluids of the copper mining were 30±4, 260±12, and 15535±322 μg L−1, respectively.in that order. When it came to extracting Mo, Pb, and Cu from the acidic fluids of the copper mining, L. gibba and L. minor performed well and efficiently compared to control samples; they did so 29 and 177 times for Mo, 30 and 109 times for Pb, and 495 and 1150 times for Cu. Considering all these findings, it has been shown that L. gibba and L. minor have the ability to efficiently remove Mo, Pb and Cu in acid mine fluids and can be good rehabilitation plants for polluted waters.