In the past decades, Fiber Reinforced Concrete has been gaining more attention in the concrete research development. There are many advantages of the inclusion of fiber into reinforced concrete structures. It was found that the inclusion of fibers in concrete, be it synthetic or natural, resulted in the improvement of the thermal properties of concrete, as well as its strength to some extent. However, the inclusion of fibers in concrete does affects its thermo-mechanical properties. The objective of this study is to identify the potential of the addition Polypropylene and Kenaf fibers in cement mortar at different compositions (0.1%, 0.2%, and 0.3%). Eight mixes were analyzed for this purpose. Upon investigating the flow ability, compressive strength, tensile strength, and thermal conductivity of the mortar samples, it was found that the incorporation of PP and Kenaf fibers reduced the flow ability. Cement mortar samples containing 0.1% addition of PP and Kenaf fibers show the highest compressive strength compared to other percentages, while samples containing 0.3% addition of PP and Kenaf fibers show the highest tensile strength compared to other percentages. The thermal conductivity of mortar samples shows reduction when high percentages of both fibers were used.

ABSTRACT Lubricants play a crucial role in reducing friction and wear between surfaces in relative motion. Engine oil, as a lubricant, is specifically designed to minimize friction and wear between the moving parts of different equipment and machinery. Engine oil blending serves the purpose of adjusting the variety of lubricants available to meet specific performance requirements. Through blending, it is possible to tailor the characteristics of the lubricating oil, such as viscosity, stability, and additive content, to optimize its effectiveness in reducing friction, protecting engine components, and enhancing overall equipment performance. By customizing lubricant formulations through blending, manufacturers can address the diverse lubrication needs of modern engines and machinery, ensuring smooth operation, longevity, and efficiency.To enhance the quality of the lubricant and achieve the desired high-performance multi-grade engine oil, a systematic approach was followed. The process began with testing the specific gravity of the oil using a hydrometer and thermometer to ensure accurate measurements. Subsequently, 5 liters of base oil were carefully measured and poured into a stainless steel reactor pot to serve as the blending vessel. Following this, 1 liter of paraffin oil (100N) was added to the base oil to introduce specific properties to the blend. To further optimize the formulation, 0.42 kg (7% of the total blend) of additives, including a selection of specific performance-enhancing compounds, was incorporated. These additives, such as Aspen, Tackifier, and other essential components like anti-wear, corrosion inhibitors, detergents, dispersants, and antioxidants, were meticulously measured and added to the mix. Through this precise blending process, the goal was to craft a high-quality multi-grade engine oil that meets the stringent performance requirements for various operating conditions and equipment types. After the melted Aspen and dissolved tackifier were added to the mixture, thorough stirring was carried out to ensure uniform distribution until a homogeneous blend was achieved. The mixture was then exposed to heat to facilitate the reaction between the base oil and additives, reaching a temperature of 70°C for optimal blending. Subsequently, 0.5 kg of viscosity index improver was introduced into the mixture and stirred continuously for a period of 5 minutes to ensure proper integration. Following this step, 5 grams of dye were carefully added to the mixture, and stirring was continued to evenly disperse the coloring agent throughout the blend. This meticulous process aimed to ensure that all components were effectively incorporated, facilitating the production of a high-quality, customized multi-grade engine oil with enhanced performance characteristics and optimal lubricating properties. After subjecting the mixture to a temperature of 70°C, the heat source was removed, allowing the product to gradually cool down to room temperature, which was estimated to be around 30°C. Following this cooling process, the product underwent a filtration step to remove any residual impurities present in the mixture. A sample of the purified product was then extracted for further analysis. Quality control tests were meticulously carried out on the sample to ensure that the product met the rigorous standards set by the Standard Organization of Nigeria (SON). The results obtained from the quality control tests were highly promising, indicating that the product indeed complied with the stringent specifications outlined by the regulatory body. This adherence to quality standards is essential in ensuring the product's reliability and performance in various applications. The successful outcome of the quality control test underscores the meticulous attention to detail and commitment to excellence in the production process. The rigorous quality control procedures implemented in the analysis of the product highlight the commitment to upholding high standards of quality and safety in the manufacturing process. By consistently meeting and exceeding industry regulations and standards, the product not only demonstrates its reliability but also reflects a dedication to customer satisfaction and product excellence. The adherence to the SON standards showcases a commitment to producing top-quality products that meet the needs and expectations of consumers and industry stakeholders alike.

Malaysia is a developing country and agro-industries contribute country’s economy. However, it is largely unknown the scenarios of agricultural practice and food supply over the years. To understand the fact, this study was designed to explore the agricultural land use changes and domestic food supply for last 50 years in Malaysia. The result showed that oil palm plantation area and yield, both are increased by folds, conforming “oil palm” mono-culture practice. Rice cultivation area remained almost unchanged but the yield increased. However, both area of plantation and yield in case of rubber, coca and coconut were decreased. When, it comes to domestic food supply, in 1973 food grain (Rice, Wheat, Maize) import was lower than domestic production. However, the import increased more than 3 times than the domestic production in 2013. Domestic production of vegetables and vegetables import was almost 50:50. Fruits import increased almost 3 times of domestic production, though domestic production was increased. In conclusion, it is understood that Malaysian agriculture economy is standing on “oil palm” wearers domestic food supply is import dependent. It is high time to reshuffle the policy for sustainable development and achieving food sovereignty.

This study aimed to determine the persistence of Salmonella Javiana, Listeria monocytogenes, and Listeria innocua in hydroponic nutrient solution (NS) at 15, 25, 30, and 37°C over a 21-day period to mimic time from seedling to mature lettuce. Bacteria were inoculated in modified Hoagland's NS at 106 CFU/ml and maintained at 15, 25, 30, and 37°C. Samples were collected at various time points and quantified. Data were analyzed using a mixed effect model to compare mean log CFU/ml obtained from each sampling point for all three bacteria at four different temperatures. Least mean squares were calculated to compare mean log CFU/ml. Tukey-Kramer honest significant difference test was used to compare mean values. At all temperatures, S. Javiana persisted in NS throughout the 21-day study period, compared to L. innocua and L. monocytogenes where persistence was limited to d 5 to d 14 and d 1 to d 14, respectively. Similarly, decimal reduction values (D-values) of S. Javiana indicated longer persistence in nutrient solution than L. innocua and L. monocytogenes at most temperatures. For instance, at 15°C and 25°C D-values for S. Javiana were estimated at 82 and 26 d, respectively, compared to D-values of 3.6 and ~3 d for L. monocytogenes. Data indicate that temperature has minimal effect on S. Javiana and thus may pose a greater risk during hydroponic production of leafy greens due to longer survival in NS when compared to Listeria spp. This study furthers the understanding of potential food safety risks associated with hydroponic systems and may aid in developing management strategies to reduce foodborne outbreaks, fresh produce recalls, and economic losses.

A series of novel asymmetrical mono-carbonyl analogs of curcumin (AMACs) were synthesized and evaluated for cytotoxic activity using the brine shrimp lethality test (BSLT) and the methyl thiazolyl tetrazolium assay against Vero, HeLa, and MCF7 cell lines. The structures of the synthesized compounds were confirmed by Fourier transform infrared spectrophotometry (FTIR), ¹H-nuclear magnetic resonance (NMR), ¹³C-NMR, and mass spectral data. The results of the cytotoxicity evaluation showed that the synthesized compounds exhibited moderate to very high toxic activity in BSLT, requiring a concentration of 13.06–714.49 µg/mL to kill half the population. Most of the compound exhibited cytotoxic activity against HeLa cell lines, comparable to the activity of cisplatin with a concentration of the synthesized compounds required to inhibit 50% of the growth of the cell lines (IC₅₀) value of 40.65–95.55 µM, and most of the compounds tested against MCF7 cell lines exhibited moderate to very high cytotoxic activity (IC₅₀ value 7.86–35.88 µM). However, the selectivity index of the compounds was low, less than 1–1.96. Among the synthesized compounds, compound 1b showed the highest cytotoxicity and selectivity against MCF7 cell lines. Compound 1b could be considered for further development to obtain more active and selective chemotherapeutic agents against breast cancer.

Land Surface Temperature (LST) is routinely retrieved from remote sensing instruments using semi-empirical relationships between top of atmosphere (TOA) radiances and LST, using ancillary data such as total column water vapor or emissivity. These algorithms are calibrated using a set of forward radiative transfer simulations that return the TOA radiances given the LST and the thermodynamic profiles. The simulations are done in order to cover a wide range of surface and atmospheric conditions and viewing geometries. This work analyses calibration strategies, considering some of the most critical factors that need to be taken into account when building a calibration dataset, covering the full dynamic range of relevant variables. A sensitivity analysis of split-windows and single channel algorithms revealed that selecting a set of atmospheric profiles that spans the full range of surface temperatures and total column water vapor combinations that are physically possible seems beneficial for the quality of the regression model. However, the calibration is extremely sensitive to the low-level structure of the atmosphere indicating that the presence of atmospheric boundary layer features such as temperature inversions or strong vertical gradients of thermodynamic properties may affect LST retrievals in a non-trivial way. This article describes the criteria established in the EUMETSAT Land Surface Analysis – Satellite Application Facility to calibrate its LST algorithms applied both for current and forthcoming sensors.

Land Surface Temperature (LST) estimation has been studied for several purposes, while the optimal method of estimating the LST has not been criticized yet. This research explores the optimum method in Land Surface Temperature (LST) estimation using LANDSAT-8 imagery data. Four different LST retrieval approaches, the Radiative Transfer Equation-based method (RTE), the Improved Mono-Window method (IMW), the Generalized Single-Channel method (GSC), and the Split-Window algorithm (SW), were calculated to present the LSTs over Buriram Town Municipality, Thailand. The calculated LSTs from these four methods were compared with the ground-based temperature data, taken on the same date and time of the employed LANDSAT-8 images. For this reason, the optimum method of the LST calculation was justified by considering the lowest normalized root means square error (NRMSE) values. As a result, the SW algorithm presents an optimum method in LST estimation. Regarding the SW, this algorithm requires not only the atmospheric profiles during satellite acquisition but also the retrieval of several coefficients. Besides, the LST retrieval method based on the SW algorithm is sensitive to water vapor content and coefficients. Although the SW algorithm is an optimum method explored in this study, it is emphasized that the adjustable values of coefficient response to the atmospheric state may be recommended. With these conditions, the SW algorithm can generate the land-surface temperature over the mixed land-use and land cover on the LANDSAT-8 images.

In this research, univariate and bivariate statistical methods were applied to rainfall, river and piezometric level datasets belonging to 24 years long time series (1986-2009). These methods, that often are used to understand the effects of precipitation on rivers and karstic springs discharge, have been used to assess, piezometric level response to rainfall and river level fluctuations in a porous aquifer. A rain gauge, a river level gauge and three wells, located in Central Italy along the lower Pescara river valley in correspondence of its important alluvial aquifer, provided the data. The statistical analysis has been used within a known hydrogeological framework, which has been refined by mean of a photo-interpretation and a GPS survey. Water-groundwater relationships were identified following the autocorrelation and cross-correlation analyses; the spectral analysis and mono-fractal features of time series were assessed, in order to provide information on multy-year variability, data distributions, their fractal dimension and the distribution return time within the historical time series. The statistical-mathematical results were interpreted through field work that identified distinct groundwater flowpaths within the aquifer and enabled the implementation of a conceptual model, improving the knowledge on water resources management tools.

A series of novel N-n-butyl-1,8-naphthalimide derivatives were synthesized via a three-step reaction involving nucleophilic substitution and acylation. All of the compounds were characterized by IR, ¹H NMR, ¹³C NMR, MS, and elemental analysis, and the crystal structure of N-n-butyl-4-[N’,N’-bis(2`,4`-dichlorobenzoyl)ethylamino]-1,8-naphthalimide was determined. The π-π stacking interactions and hydrogen bonds between the two molecular core planes (naphthalimide ring) and the van der Waals forces between the flexible n-butyl groups resulted in a 3D long-chain structure. The UV-vis and fluorescence properties of the title compounds were investigated. The results indicated that the monosubstituted 1,8-naphthalimide derivatives bearing an electron-donating group on the benzene ring or a structure with a larger conjugative effect exhibited enhanced fluorescence properties.

In this work, we studied light-output properties, efficiency function as well as PSD capability of p-Terphenyl scintillator. The selected solid cylindrical scintillation detector has a size of (45 x 45) mm with PSD properties. Recently presented studies of light-output functions have been measured only for low neutron energies. Our motivation has been to determine more accurate the light output function for p-Terphenyl scintillator over a wider neutron energy range.

The effect of elastic constants, cij, on the nature (easy or difficult) of a cleavage system in YBa2Cu3O7−δ is investigated, by employing a novel three-dimensional eigenfunction expansion technique, based in part on separation of the thickness-variable and partly a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism. Out of the available three complete sets of elastic constants, the first constitutes an estimate, while the second assumes tetragonal symmetry. This leaves only the experimental measurements by resonant ultrasound spectroscopy, despite reported values of c12 and to a lesser extent, c66, being excessively high. The present investigation considers six through-thickness crack systems weakening orthorhombic YBCO mon-crystalline plates. More important, the present approach predicts whether a crack would propagate in its original plane/direction or deflect to a different one. This fracture mechanics criterion is then employed for accurate determination of the full set of elastic constants of mono-crystalline YBCO. Finally, generally unavailable results, pertaining to the through-thickness variations of stress intensity factors and energy release rates for a crack corresponding to symmetric and skew-symmetric hyperbolic cosine loads that also satisfy the boundary conditions on the bounding surfaces of an orthorhombic monocrystalline plate bridge a longstanding gap in the field.