Large ruminant production is associated with high greenhouse gas emissions (GHGe) intensity, with the highest in southeast Asia being Laos at 102.9 CO2eq/kg meat produced, compared with average global meat emissions intensity of 33 CO2eq/kg. As recent studies in Laos identified emissions control molasses blocks (ECBs) achieved abatement of 470kg CO2eq/20kg block consumed, a study was conducted with a supplement mix with reported methane reducing properties, containing plant tannins and citral extract, salt, molasses and water. Groups of housed dairy buffalo (n=7) and pasture-fed grazing beef cows (n=11) were randomly selected, body condition scores estimated (BCS:1-5) and baseline nasa-oral methane eructation measured daily for 2 weeks. All animals were offered 300-400g/day of the mix for a month, with buffalo accessing abundant fresh cut forages whereas the grazing cows accessing rice straw and pasture declining in quality and quantity due to severe drought. The buffalo consumed all of the mix and retained their BCS of 3, whereas the cattle consumed between 200-300g/day of the mix and their BCS declined from 1.5 to 1.0 during the trial. Analysis of data points (buffalo n=309; cattle n=378) found average methane concentration (AMP) per animal of both cohorts increased over the 2 week baseline period, then declined during the supplementation period by 36% in the buffalo and 18% in cattle cohorts.

Environmental assessment is a concept that has been designed to facilitate the present generation to meet their needs without compromising the ability of future generations to meet their own needs as well. Thus, this concept has drawn significant attention from various scholars, researchers and industrial practitioners around the world over the past three decades. Life Cycle Environmental Assessment (LCEA) is a widely metric used to assess the potential ecological impacts, which can be caused by electricity generating supply systems or by other systems than power production plants. However, the current LCEA model is biased and ineffective. Because, its omits factors that are increasingly contributing to the ecological degradation. This study has identified the omitted factors through a critical analysis of a set of previous journal articles conducted in the energy sector. In light of this, this study has developed a novel LCEA framework addressing those blind spots. The framework developed in this study is holistic in nature including all the life cycle stages of a power supply system such as Extraction of the Raw Material (ERM), Transport of Raw Material (TRM), Conversion of Raw into Electricity (CRE), and Transmission and Distribution of Electricity (TDE) to the end users. The novel developed LCEA model has been tested and applied to nine power generation plants such as coal, gas, nuclear, biomass, geothermal, hydro, solar thermal, wind onshore and wind offshore. The results have demonstrated that of conventional technologies including coal, gas, and nuclear, coal energy generating source has got the highest life cycle greenhouse gas Grid Emission Factor (GEF) of 2866 kg CO2e/MWh, followed by gas with 728 kg CO2e/MWh, and nuclear has got the least GEF of 35 kg CO2e/MWh. Whereas of renewable energy sources biomass has got the highest GEF of 1508 kg CO2e/MWh, followed by solar thermal with 46.6 kg CO2e/MWh, hydro 39 kg CO2e/MWh, wind offshore 25.25 kg CO2e/MWh, wind onshore 10.1 kg CO2e/MWh, and geothermal closes the ranking with 6.23 kg CO2e/MWh.

The important topic of climate change is discussed in this article, with a focus on the historical background and present effects. It draws attention to the differences between climate change and global warming and attributes the faster pace of climate change to human activity, specifically the release of greenhouse gases into the atmosphere. Agricultural practices, deforestation, and the combustion of fossil fuels are examined in conjunction with natural contributors like volcanic emissions. There is discussion of the far-reaching effects of climate change, such as increased temperatures, rising sea levels, harsh weather, and effects on water supplies. The article emphasizes how crucial it is to mitigate and adapt to the effects of climate change by putting in place climate-resilient infrastructure, switching to renewable energy sources, and lowering greenhouse gas emissions. While recognizing the difficulties involved, it examines several approaches, including nuclear energy, wind power, carbon capture and storage, and green building techniques. To successfully address the global challenge of climate change, the conclusion emphasizes the urgent need for joint efforts by scientists, environmentalists, communities, and governments.

It is well-established that plants are sessile and photoautotrophic organisms that rely on light throughout their entire life cycle. Light quality (spectral composition) is especially important as it provides energy for photosynthesis and influences signaling pathways that regulate plant devel-opment in the complex process of photomorphogenesis. During past years, significant progress has been made in the physiological and biochemical effects of light quality on crops. However, understanding how light quality modulates plant growth and development remains a complex challenge. In this review, we provide an overview of the role of light quality in regulating early development of plants, encompassing processes such as seed germination, seedling de-etiolation, and seedling establishment. These insights can be harnessed to improve production planning and crop quality by producing high-quality seedlings in plant factories and improving the theoretical framework for modern agriculture.

Southern highbush blueberry plantations have been expanded into worldwide non-traditional growing areas with elite cultivars and improved horticultural practices. This article presents a comprehensive review of current production systems – alternatives to traditional open field production – such as production in protected environments, high-density plantings, evergreen production, and container-based production. We discuss the advantages and disadvantages of each system and compare their differences to the open field production. In addition, potential solutions have been provided for some of the disadvantages. We also highlight some of the gaps existing between academic studies and production in industry, providing a guide for future academic research. All these alternative systems have shown the potential to produce high yields with high quality berries. Alternative systems, compared to the field production, require higher establishment investments and thus create an entry barrier for new producers. Nevertheless, with their advantages, alternative productions have potential to be profitable.

Environmental pollution is becoming ubiquitous; it has a negative impact on the ecosystem diversity and worsens the quality of human life. This review discusses the possibility of applying the Plant Microbial Fuel Cells (PMFC) technology for concurrent processes of electricity generation, purification of water and soil ecosystems from organic pollutants, in particular, from synthetic surfactants and heavy metals. The review describes the PMFC functioning mechanisms and highlights the issues of the PMFC environmental application. Generally, this work summarizes different approaches to the PMFC development and to the potential usage of such hybrid bioelectrochemical systems for the environmental protection.

(1) Background: Human-generated greenhouse gas (GHG) emissions are the largest contributor to climate change worldwide. Climate change negatively impacts human and planetary health threatening the existence of life on earth. The healthcare industry is responsible for approximately 8.5% of carbon emissions in the United States. Measuring baseline GHG emissions is the first step in emissions reduction. However, very few models of measurement exist for health care organizations. This project aimed to develop and implement a program to measure and track GHG emissions at a Midwestern Academic Medical Center (MAMC) and to educate staff to manage the process. (2) Methods: A Plan, Do, Study, Act (PDSA) cycle and Quality Improvement methodology was used to develop, implement, and assess a standardized GHG emission inventory process to measure Scope 1 and Scope 2 baseline emissions, and provide virtual training and education to the accountable staff. A pre- and post-survey design was used to measure the knowledge and readiness of the staff after the implementation of the GHG inventory training. (3) Results: The GHG inventory process was validated through an external verification process and the measurement of Scope 1 and Scope 2 baseline GHG emissions was completed and verified for accuracy through a data comparison review. The pre-post-training survey showed an increase in the knowledge and readiness of staff in maintaining a GHG inventory. (4) Conclusions: This work shows the feasibility of obtaining baseline GHG emissions data at large medical centers. It represents the initial phase of the overarching goal to develop site-wide and system-wide carbon reduction strategies and a climate action plan within this health system.

High efficacy LED lamps combined with adaptive lighting control and greenhouse integrated photovoltaics (PV) could enable the concept of year-round cultivation and become a feasible option even in the harsh climate of the Nordic countries. Meteorological satellite data of this region was analyzed in a parametric study to evaluate the potential of these technologies. The generated maps showed monthly average temperatures fluctuating from -20°C to 20°C throughout the year. The natural photoperiod and light intensity also changed drastically, resulting in monthly average daily light integral (DLI) levels ranging from 45-50 mol·m-2·d-1 in summer and contrasting with 0-5 mol·m-2·d-1 during winter. To compensate, growth room cultivation independent from outdoor conditions could be used in winter. Depending on the efficacy of the lamps, the electricity required for sole-source lighting at 300 µmol·m-2·s-1 for 16 hours would be between 1.4 and 2.4 kWh·m-2·d-1. Greenhouses with supplementary lighting could help start the cultivation earlier in spring and extend it further into autumn. The energy required for lighting highly depends on several factors such as the natural light transmittance, the light threshold settings and the lighting control protocol, resulting in electric demands between 0.6 and 2.4 kWh·m-2·d-1. Integrating PV on the roof or wall structures of the greenhouse could offset some of this electricity, with specific energy yields ranging from 400 to 1120 kWh·kWp-2·yr-1 depending on the region and system design.

Initial evaluations of the System of Rice Intensification in India and elsewhere have mainly fo-cused on its impact on yield and income and have usually covered just one or two seasons. Re-searchers at the ICAR-Indian Institute of Rice Research conducted a more comprehensive evalua-tion of SRI methods over six years (six wet and six dry seasons), comparing these methods with three other rice crop management systems: modified, partially mechanized SRI (MSRI); direct-seeded rice (DSR); and normal transplanting with inundated fields (NTP). SRI grain yield was found to be about 50% higher than with NTP (6.35 t ha-1 vs 4.27 t ha-1), while the MSRI yield was essentially the same (6.34 t ha-1) and 16% higher than with DSR (5.45 t ha-1). Compared to NTP, SRI methods significantly enhanced soil microbial populations over time, bacteria by 12%, fungi by 8%, and actinomycetes by 20%. Indicators of biological activity in the rhizosphere were also higher, dehydrogenase by 8.5% and FDA enzymes by 16%. Glucosidase activity, an indicator of soil organic matter, was 78% higher. Relative to normal transplanting methods, SRI reduced GHG emissions by 21%, while DSR reduced them by 23% and MSRI by 13%, which indicated pos-itive effects of the alternate and improved methods over normal transplanting. Economic analy-sis showed that both gross and net economic returns to be higher with SRI than with MSRI and the other management systems evaluated. While the six-year study documented many ad-vantages of SRI crop management, the MSRI version evaluated is a promising adaptation that provide similar benefits but with lower labor requirements.

Cement manufacturing is one of the most energy-intensive industries in the world. Most of the cost of producing cement is accounted by fuel consumption and power expenditures. Thermal power plants are the major source of electricity in Pakistan. But they are not efficient and environmentally friendly. This study simulates four different models for five cement plants of Pakistan on Homer Pro software and compares the optimal solutions based on the net present cost (NPC), levelized cost of electricity (LCOE) and greenhouse gas (GHG) emissions. Model-1 consists of solar panels, electrolyzer, hydrogen tank, hydrogen generator and converter. Model-2 has only a diesel generator and acts as a base case in this study. Model-3 has solar panels and a battery-converter system. In Model-4, diesel generators, solar panels and converters are considered. Based on NPC, the most optimal model is Model-4, having a 0.249 $/KWh LCOE in islanded systems. The NPC and operating costs are US$540 million and US$ 32.5 million per year, respectively, with a 29.80% reduction in CO2 emissions when compared to the base case. Based on GHG emissions, Model-1 and Model-3 are the best models with 0% GHG emissions. Sensitivity analyses is also performed using the parameters of load, inflation rate and discounted rate. The results prove that the proposed hybrid micropower systems (HMS) can sustainably provide electricity for 24 hours a day to the sites under consideration with minimum objectives.

A cross-flow ultrafiltration harvesting system of a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with the effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomass was then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L1 with an average of 9.7 g·L1). Concentration ratios of 15-27 were obtained with average transmembrane fluxes ranged from 5 to 28 L·m2·h1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from the biogas production from the anaerobic valorisation of the harvested microalgae.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

This paper provides an in-depth exploration of the role of Big Data and Artificial Intelligence (AI) in advancing dairy farming towards net zero emissions, a critical goal in the face of the global climate crisis. The study emphasizes how these technologies significantly enhance the management of greenhouse gas (GHG) emissions and optimize resource use, thereby contributing to environmental sustainability in agriculture. A key aspect of this transition is the alignment with international climate commitments, such as the Paris Agreement, which are instrumental in steering global efforts toward emission reduction and mitigating climate change. The integration of Big Data and AI in dairy farming emerges as a powerful tool to reduce the sector's environmental impact while sustaining economic growth. The paper delves into the specific applications of these technologies in emission management, including predictive analytics for feed optimization, manure management, and energy efficiency enhancements. It also addresses the broader implications of technological integration in dairy farming, considering aspects like benchmarking standards, data privacy, and the role of policy in fostering sustainable practices. The study underscores the challenges inherent in adopting these advanced technologies, including the need for improved farmer training, data quality, and compatibility with existing systems. It also advocates for enhanced policy frameworks that support sustainable practices, encourage technological adoption, and balance economic viability with environmental responsibility. This comprehensive analysis offers valuable insights into harnessing digital technologies for climate change mitigation and delineates a path for the dairy industry towards achieving net zero emissions, thereby contributing significantly to global environmental sustainability efforts.

This paper responds to the research question, “can urban farming help Nepali cities become more sustainable”? Especially after the Covid-19 pandemic, urban residents have begun to realize that food transported from long distances could not always be reliable. Urban farming can help produce fresh food locally and avoid long-distance transportation, and refrigeration. This practice also helps reduce greenhouse gases through plant carbon use efficiency (CUE). Urban farming not only helps city-dwellers towards achieving self-reliance in food production but also in vegetation carbon dynamics (VCD) while supporting the circular economy. Urban farming consists of edible landscapes, which can also be an aesthetic public space. As urban lands command higher prices than agricultural land, urban farming usually happens on residential yards, roofs, balconies, community gardens, and dedicated areas in public parks. Rainwater harvesting, and redirecting can help irrigate urban farms which can be part of rain gardens. The national census of 2021 (CBS 2022, p5) identifies that 66 percent of Nepal’s population live in urban areas. However, the World Bank (2018), shows that only 21 of Nepal’s population was projected to live in urban areas in 2021. It is not debatable that the urbanization process in Nepal is on the rise. Thus, urban agriculture can play an important role to supplement the residents’ food needs. Many cities in Nepal have already successfully adapted to urban farming where residents grow food on their building site, balconies, and rooftop often growing plants on pots, vases, and other types of containers. The UN-Habitat, with the support of European Union and local agencies, has published a rooftop farming training manual (2014) showing the feasibility of urban farming in Nepal.The paper discusses how Public Private Partnership (PPP) can promote urban agriculture and make the process more effective and attractive to urban farming households. It also analyzes how a PPP approach also facilitates the use of better technology, advisory support, and use of research extension activities. This paper draws on literature review, secondary data (e.g., from National Census Nepal 2021) and authors’ professional experiences related to best practices in the areas to analyze the benefits and challenges related to urban farming in Arizona, USA. The paper will provide recommendations for Nepali cities to maximize the benefit provided by urban farming. It is expected to be useful to Nepali policy makers, and government agencies, and nonprofit organizations which promote sustainability, and organic farming.

Cement industry is one of the highest energy consuming industries. The quantity of fuel and energy needed accounts for most of the cost of cement manufacturing. Thermal power plants generate electricity but are harmful and ineffective by nature. As a backup mechanism to account for main grid failures, batteries can be utilized. In this paper the first ever investigation on battery’s depth of discharge (DOD) for four different kinds of battery technologies is carried out in the framework of cement industry. The intended battery technologies are the lead-acid battery (LA), lithium-ion battery (Li-ion), vana-dium redox battery (VR), and nickel–iron battery (Ni-Fe). Four hybrid energy generation models (HEGMs) for five cement plants of Pakistan using the HOMER pro software are proposed. Cement plants includes Askari Cement Plant, Wah (ACPW); Bestway Cement Plant, Kalar Kahar (BCPKK); Bestway Cement Plant, Farooqia (BCPF); Bestway Cement Plant, Hattar (BCPH); and DG Cement Plant, Chakwal (DGCPC). HEGM-1 comprises of a diesel generator (DGen), a photovoltaic system (PV), a converter, and a battery system. HEGM-2 comprises of a PV system, a converter, and a battery system. HEGM-3 is the grid-connected version of HEGM-1 and HEGM-4 is the grid-connected version of HEGM-2. A base-model consisting of grid only is used as a reference. A multi-criteria decision analysis (MCDA) is performed by formulating a cumulative objective function (COF) which includes net present cost (NPC), levelized cost of energy (LCOE), and greenhouse gas (GHG) emissions. The principal objective is the maximization of COF while simultaneously minimizing the objectives (NPC, LCOE and GHG emissions), based on optimal battery technology and DOD. The results reveal that VR is the most suitable battery technology with 10% DOD. It is achieved for DGCPC with HEGM-3 with 61.49% of NPC, 78.62% of LCOE and 84.00% of GHG emissions reduction as com-pared to the base model.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

The building sector has a big potential to reduce the material resource demand needed for building construction and therefore, greenhouse gas (GHG) emissions. Digitalisation can help to make use of this potential and improve sustainability throughout the entire building’s life cycle. One way to address this potential is through the integration of Life-Cycle Assessment (LCA) into the building process by employing Building Information Modelling (BIM). BIM can reduce the effort needed to carry out an LCA and therefore facilitate the integration into the building process. A review of current industry practice and scientific literature shows two main approaches to address BIM-LCA integration. Either the LCA is performed in a simplified way at the beginning of the building process, or it is done at the very end when all the needed information is available, but it is too late for decision-making. One reason for this is the lack of methods, workflows and tools to implement BIM-LCA integration over the entire building process. Therefore, the main objective of this study is to develop an integrated BIM-LCA workflow implemented into a method for the whole building process using an existing structure for cost estimation. A tool is created and used in a case study in Switzerland to test the developed approach. The results of this study show that LCA can be performed continuously in each building phase over the entire building process using existing BIM modelling techniques. The main benefit of this approach is that the re-work caused by the need for re-entering data and the usage of many different software tools that characterise most of the current LCA practices is minimised. Furthermore, decision-making, both at the element and building levels, is supported.