In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

Repetitive transcranial magnetic stimulation (rTMS) with intensive occupational therapy improves upper limb motor paralysis and activities of daily living after stroke; however, amount of improvement according to paralysis severity remains unverified. Target activities for daily living using patients’ upper limb functions can be established by predicting the amount of change after treatment for each severity level of upper limb motor paralysis and further aid practice planning. This study estimated post-treatment score changes for each severity level of motor paralysis (no, poor, limited, notable, and full) stratified according to Action Research Arm Test (ARAT) scores before combined rTMS and intensive occupational therapy. Severity of motor paralysis was the fixed factor for analysis of covariance, delta (post-pre) of the scores was the dependent variable. Ordinal logistic regression analysis was used to compare changes in ARAT subscores in patients, divided according to paralysis severity before treatment. A multicenter retrospective cohort dataset analyzed 907 patients with stroke hemiplegia. Largest treatment-related changes in scores were observed in the Limited recovery group for upper limb motor paralysis and Full recovery group for quality-of-life activities using paralyzed upper limb. These results will help predict treatment effects and determine exercises and goal movements for occupational therapy after rTMS.

The diffusion process of water molecules within a polyetherimide (PEI) glassy matrix has been analyzed by combining the experimental analysis of water sorption kinetics performed by FTIR spectroscopy with theoretical information gathered from Molecular Dynamics simulations and with the expression of water chemical potential provided by a non-equilibrium lattice fluid model able to describe the thermodynamics of glassy polymers. This approach allowed to construct a convincing description of the diffusion mechanism of water in PEI providing molecular details of the process related to the effects of the cross- and self-hydrogen bondings established in the system on the dynamics of water mass transport.

Nanoparticles have been used as a novel drug delivery system. Drug-incorporated nanoparticles for local delivery might optimize the efficacy and minimize the side effects of drugs. The efficacy and safety of intratracheal administration of prostacyclin analog (beraprost)-incorporated nanoparticles and imatinib, a PDGF-receptor tyrosine kinase inhibitor, -incorporated nanoparticles in Sugen-hypoxia-normoxia or monocrotaline rat models of PAH and in human PAH-pulmonary arterial smooth muscle cells have been reported. The use of inhaled drug-incorporated nanoparticles might be a novel approach for treatment of PAH.