Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance & Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (<3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

Spatial variation of indoor and outdoor PM2.5 within three states for a 5-year period is studied using regulatory and low-cost PurpleAir monitors. Most of these data were collected in an earlier study1 investigating the relative contribution of indoor-generated and outdoor-infiltrated particles to indoor exposures. About 260 regulatory monitors and ~10,000 outdoor and ~4,000 indoor PurpleAir monitors are included. Daily mean PM2.5 concentrations, correlations, and coefficients of divergence (COD) are calculated for pairs of monitors at distances ranging from 0 (collocated) to 200 km. We use a transparent and reproducible open algorithm that avoids use of the proprietary algorithms provided by the manufacturer of the sensors in PurpleAir PA-I and PA-II monitors. The algorithm is available on the PurpleAir API website under the name “PM2.5_alt”. This algorithm is validated using several hundred pairs of regulatory and PurpleAir monitors separated by up to 0.5 km. The PM2.5 spatial variation outdoors is homogeneous with high correlations to at least 10 km, as shown by the COD index under 0.2. There is also a steady improvement in outdoor PM2.5 concentrations with increasing distance from the regulatory monitors. The spatial variation of indoor PM2.5 indoors is not homogeneous even at distances <100 m. We document substantial differences between Federal Reference Methods (FRM) and Federal Equivalent Methods (FEM).

Low-cost sensors are widely used for air quality monitoring due to their affordability, portability and easy maintenance. However, the performance of such sensors, such as PurpleAir Sensors (PAS), is often affected by changes in environmental (e.g., temperature and humidity) or emission conditions, and hence the resulting measurements require corrections to ensure accuracy and validity. Traditional correction methods, like those developed by the US-EPA, have limitations, particularly for applications to geographically diverse settings and sensors with no collocated referenced monitoring stations available. This study introduces BaySurcls, a Bayesian-optimised surrogate model integrating deep learning (DL) algorithms to improve the PurpleAir sensors PM2.5 (PAS2.5) measurement accuracy. The framework incorporates environmental variables such as humidity and temperature alongside aerosol characteristics, to refine sensor readings. The BaySurcls model corrects the PAS2.5 data for both collocated and non-collocated monitoring scenarios. A case study showed that BaySurcls outperforms all tested standalone models (DL or classical machine learning based) and the US-EPA correction method in terms of reducing root mean square errors in PAS2.5 data and enhancing correlations with the reference data, under both the collocation and non-collocation monitoring scenarios. This improvement is evident across multiple locations in New South Wales, Australia, demonstrating the model's adaptability. The findings confirm BaySurcls as a promising solution for improving the reliability of low-cost sensor data, thus facilitating its valid use in air quality research, impact assessment, and environmental management.

Large quantities of real-time particle data are becoming available from low-cost particle monitors. However, it is crucial to determine the quality of these measurements. The largest network of monitors in the United States is maintained by the PurpleAir company, which offers two monitors: PA-I and PA-II. PA-I monitors have a single sensor (PMS1003) and PA-II monitors employ two independent PMS5003 sensors. We determine a new calibration factor for the PA-I monitor and revise a previously published calibration algorithm for PA-II monitors (ALT-CF3). From the PurpleAir API site, we downloaded 83 million hourly average PM2.5 values in the PurpleAir database from Washington, Oregon, and California between January 1, 2017 and September 8, 2021. Daily outdoor PM2.5 means from 194 PA-II monitors were compared to daily means from 47 nearby Federal regulatory sites using gravimetric Federal Reference Methods (FRM). We find a revised calibration factor of 3.4 for the PA-II monitors. For the PA-I monitors, we determined a new calibration factor (also 3.4) by comparing 26 outdoor PA-I sites to 117 nearby outdoor PA-II sites. These results show that PurpleAir PM2.5 measurements can agree well with regulatory monitors when an optimum calibration factor is found.

Low-cost particle sensors are now used worldwide to monitor outdoor air quality. However, they have only been in wide use for a few years. Are they reliable? Does their performance deteriorate over time? Are the algorithms for calculating PM2.5 provided by the Plantower company for PurpleAir monitors accurate? We investigate these questions using continuous measurements of four monitors (8 sensors) under normal conditions inside and outside a home for 1.5-3 years. A recently-developed algorithm (called ALT-CF3) is compared to the two existing Plantower algorithms. The Plantower CF1 algorithm was shown to lose 25-50% of all indoor data due to the questionable practice of assigning zero to all concentrations below a threshold. None of these data were lost using the ALT-CF3 algorithm. About 92% of all data showed precision better than 20% using the ALT-CF3 algorithm, but only about 45-75% of data achieved that level using the Plantower CF1 algorithm. The limits of detection (LODs) using the ALT-CF3 algorithm were mostly under 1 ug/m3, compared to about 3-10 ug/m3 using the Plantower CF1 algorithm. The percent of observations exceeding the LOD was 53-92% for the ALT-CF3 algorithm, but only 16-44% for the Plantower CF1 algorithm. For indoor air in homes, the Plantower algorithms are inappropriate.

Low-cost monitors make it possible now for the first time to collect long-term (months to years) measurements of potential indoor exposure to fine particles. Indoor exposure is due to two sources: particles infiltrating from outdoors and those generated by indoor activities. Calculating the relative contribution of each source requires identifying an infiltration factor. We develop a method of identifying periods when the infiltration factor is not constant, and searching for periods when it is relatively constant. From an initial regression of indoor on outdoor particle concentrations, a Forbidden Zone can be defined with an upper boundary below which no observations should appear. If many observations appear in the Forbidden Zone, they falsify the assumption of a single constant infiltration factor. This is a useful quality assurance feature, since investigators may then search for subsets of the data in which few observations appear in the Forbidden Zone. The usefulness of this approach is illustrated using examples drawn from the PurpleAir network of optical particle monitors. An improved algorithm is applied with reduced bias, improved precision, and a lower limit of detection than either of the two proprietary algorithms offered by the manufacturer of the sensors used in PurpleAir monitors.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.