In order to study the feasibility of copper-nickel smelting slag（CNSS） and palygorskite for large-scale consumption and utilization in the field of mine filling, gellable composite materials were prepared from copper-nickel smelting slag ,cement and palygorskite. The effects of palygorskite addition and curing time on the mechanical properties and microstructure of copper-nickel smelting slag-based cementitious materials were studied in detail. The results showed that the addition of palygorskite had a positive effect on the curing of the cemented filler of the non-ferrous smelting slag by promoting the early hydration reaction. palygorskite also affected the mechanical properties of the cementitious materials with different maintenance times and the ability to cure heavy metals. The strength of gellable composite materials reaches 23.05MPa when 1% palygorskite, 50% of copper-nickel smelting slag and 48% cement were used, which meet the standards requirements of filling materials for mine goaf. The addition of 1% palygorskite can improve the ability of cementitious materials to solidify heavy metals to realize the economic utilization of solid waste in mining areas.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

This work discussed the advantages of reducing copper in molten copper slag with low S content. FactSage calculated the distribution of copper at equilibrium under different sulfur content. The effect of sulfur content on copper recovery under different oxygen partial pressures was pointed out. The effect of sulfur content on copper recovery in the actual reduction process was explored through experimental research. Under the condition of low sulfur, the Recovery of copper and the stability of the experiment have an ideal results.

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

There is a high iron content in the nickel slag that mainly exists in fayalite phase. Basic Oxide can destroy the stable structure of fayalite which is beneficial to the treatment and comprehensive utilization of nickel slag. The reseach was based on the composition of the raw nickel slag, taking CaO-SiO₂-FeO-MgO system as the object and CaO as a modifier. The effect of basicity on the melting characteristics, viscosity and structure of CaO-SiO₂-FeO-MgO system was studied. The relationship between the viscosity and structure of CaO-SiO₂-FeO-MgO system was also explored. The results show as follows. (1) When the basicity is 0.38~0.90, the phase of primary crystal is olivine at argon atmosphere, while it is monoxide at the basicity of 0.90~1.50. The liquidus temperature, softening temperature, hemispherical temperature, and flow temperature all reach the lowest value at the basicity of 0.90. (2) With the increase of basicity, critical viscosity temperature of CaO-SiO₂-FeO-MgO system decreases first and then increases. Critical viscosity temperature is the lowest at the basicity of 0.90, which is 1263 ℃. (3) When the slag system is heterogeneous, the viscosity of the molten slag increase rapidity because of the type and quantity of solid phase precipitated from CaO-SiO₂-FeO-MgO system. And critical viscosity temperature of the slag system is also significantly affected. (4) When the slag system is in a homogeneous liquid phase, the molar fraction of O0 decreases with the increase of basicity and the mole fraction of O^- and O^2- increases continuously at the basicity of 0.38~1.50. The silicate network structure is gradually depolymerized into simple monomers, resulting in the degree of polymerization is reduced and the viscosity is reduced, too.

The aim of the research was a comprehensive evaluation of concrete using the EIPI method. In the evaluation the compressive strength of concrete and its durability properties represented by sorptivity and air permeability were taken into account. Since copper slag waste with increased natural radioactivity was used in the assessed concrete, additional evaluation was carried out taking into account the influence of natural radioactivity within the performance index. Also the reference concrete, which was made without the use of copper slag waste, was evaluated for comparative purposes. In order to make the evaluation as comprehensive as possible, the concrete made with the use of three types of cement was subjected to the assessment: CEM I, CEM II and CEM III. The results show that in both approaches the best result was achieved by concrete with CEM III cement. If natural radioactivity is not taken into account in the evaluation, the best result is obtained by concrete made with copper slag waste, and if radioactivity is considered, the best result is obtained with concrete without addition of the waste. It follows from the above that although natural radioactivity has a significant impact on the EIPI evaluation result, the decisive factor is still the type of cement.

The depletion of the ore reserves in the world necessitates the search for secondary sources such as waste products (tailings and slag). A smelter in Namibia has historic slag which accumulated over decades of its operating life. Analytical and mineralogical characterization of the slag was performed using the X-ray fluorescence (XRF) analysis, Atomic Absorption Spectrometer (AAS), ICP-OES, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, and optical microscopy analysis. The chemical analyses showed that the metal values contained in the slag were mainly copper, lead, and zinc whose average contents were approximately 0.3%Cu, 2.4%Pb and 3.2%Zn. About 10.5%Fe was also contained in the slag. Germanium was detected by scanning electron microscopy, but was however below detection limits of the chemical analysis equipment used. Based on the results, approximate conditions under which the different slag phases were formed were estimated and the recovery routes for the various metals were proposed. Analysis by both optical and scanning electron microscopy revealed that Zn and Fe occurred mainly in association with O as oxides, while Cu and Pb were mainly associated with S as sulphides. The slag consisted of three different phases; namely the silicate phase (slag), metallic phase and the sulphide phases. The slag phases were mainly glass, silicate phases and metallic and sulphide phases. It was observed that the metallic and sulphide phases were dominant in the finer size fractions (-75 µm) whereas the sulphide phase was also present in the coarser size fractions (+300 µm). An important finding from the microscopy examination was that the sulphide phases were interstitial and could be liberated from the slag. This finding meant that liberation and subsequent concentration of the sulphide phases was feasible using conventional processing techniques.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

Nickel-based ethylene polymerization catalysts have unique features, being able to produce macromolecules with a variable content of branches, resulting in polymers ranging from semicrystalline plastics to elastomers to hyperbranched amorphous waxes and oils. In addition to Brookhart's α-diimine catalysts, iminopyridine Ni(II) complexes are among the most investigated systems. We report that Ni(II) complexes bearing aryliminopyridine ligands with bulky substituents both at the imino moiety and in the 6-position of pyridine afford either hyperbranched low molecular weight polyethylene oils or prevailingly linear crystalline polyethylenes or both depending on the ligand structure and the reaction conditions. The formation of multiple active species in situ is suggested by analysis of the post-polymerization catalyst residues, showing the partial reduction of the imino function. Some related arylaminopyridine Ni(II) complexes were also synthesized and tested, showing a peculiar behavior, i.e. the number of branches of the produced polyethylenes increases while ethylene pressure increases.

Information taken from David A. Scott’s book “Copper and Bronze in Art” was crucial for research on copper corrosion products in Stuttgart. Examples discussed are the nature and variability of ‘Black Spots’ (aka ‘Brown Fuzzies’); cupric hydroxide by cleaning, patination, and pigment synthesis; the wondrous phenomenon of curly malachite; chalconatronite formed by contact to soda glass; the formation of copper formates by glass-induced metal corrosion; and synthesis and X-ray diffraction of basic copper acetates (‘verdigris’).

Metallic masters can be used as a metallic mold to replicate polymeric pieces with high resolution. Metallic masters with high resolution were created by photolithography technique and nickel electrodeposition technique. AZ 9260 photoresists and SPR 220-7.0 photoresists were used to coat metallic substrates and to compare results. Steel substrate and nickel substrate were used as the metallic substrate to compare results. Two different nickel electrodeposition protocols were used to compare results. In the conclusion section, was determined the best photoresist, metallic substrate, and nickel electrodeposition protocol to fabricate metallic masters.

In this scientific research, thermally stable nickel nanoparticles were synthesized and characterized. Nickel nanoparticles were synthesized using phenol –formaldehyde by chemical method followed by calcination. The polymer metal complex was confirmed by FTIR and NMR. The spherical morphology of nickel nanoparticles confirmed by SEM. The crystallographic structure is confirmed by XRD and size of cobalt nanoparticles is 24.0 nm. The TGA analysis was performed over a range of 29-600OC. The TGA thermograph predicts mass decomposition of 11%, for nickel phenol-formaldehyde nanocomposite. The decomposition rate of composites is very low 2% weight loss per 100OC increment in temperature.

Iron-containing nickel sulfides, selenides, and sulfoselenides were synthesized via a simple two-step hydrothermal reaction (temperature 160 °C) for their application as electrocatalysts in the oxygen evolution reaction (OER) in an alkaline solution (1 mol L–1 KOH). The study demonstrated that iron-containing nickel cobalt sulfides and selenides exhibit superior OER performance with lower overpotentials compared to iron-free nickel cobalt sulfide and selenide, which highlights the significant role of iron in enhancing OER nickel cobalt electrocatalysts: Fe0.1Ni1.4Co2.9(S0.87O0.13)4, η50 = 318 mV; Fe0.2Ni1.5Co2.8(S0.9O0.1)4, η50 = 310 mV; Fe0.3Ni1.2Co2.5(S0.9O0.1)4, η50 = 294 mV; Fe0.6Ni1.2Co2.5(S0.83O0.17)4, η50 = 294 mV, Fe0.4Ni0.7Co1.6(Se0.81O0.19)4, η50 = 306 mV compared to Ni1.0Co2.1(S0.9O0.1)4, η50 = 346 mV and Ni0.7Co1.4(Se0.85O0.15)4, η50 = 355 mV (all values at current densities η50 of 50 mA cm–2). Furthermore, the iron-containing nickel cobalt sulfoselenide Fe0.5Ni1.0Co2.0(S0.57Se0.25O0.18)4 displayed exceptional OER performance with η50 = 277 mV, surpassing the benchmark RuO2 electrode with η50 = 299 mV. The superior performance of the sulfoselenide was attributed to its low charge transfer resistance (Rct) of 0.8 Ω at 1.5 V vs. the reversible hydrogen electrode (RHE). Moreover, the sulfoselenide demonstrated remarkable stability, with only a minimal increase in overpotential (η50) from 277 mV to 279 mV after a 20 h chronopotentiometry test. These findings suggest that trimetallic iron, nickel and cobalt sulfide, selenide and especially sulfoselenide materials hold promise as high-performance, cost-effective, and durable electrocatalysts for sustainable OER reactions. This study provides a valuable approach for the development of efficient electrocatalytic materials, contributing to the advancement of renewable energy technologies.

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

The frequent occurrence of rib fractures in slaughtered lambs results in significant economic loss to producers and processors in South Australia and raises concerns about the welfare of the animals. The prevalence of rib fractures became evident through the Enhanced Abattoir Surveillance (EAS) program introduced in 2007. The present study aimed to investigate the association between rib fracture prevalence in lambs at slaughter and their nutrition and management on the farm of origin. The slaughter of 30,055 lambs from 60 farms was monitored at a South Australian abattoir in November 2016. Rib fracture prevalence was 4% (range 0 - 18% per consignment), with all consignments of more than 240 lambs having at least one with fractured ribs. Traceback investigation on 56 of the 60 farms suggests that rib fractures most probably occur during routine husbandry procedures and, based on soil mineral analysis, are associated with calcium inadequacy. There was substantial variation between lines of lambs from different farms, and factors contributing to the differences included line size, region, and soil characteristics, including available calcium. There is a need to modify sheep husbandry and management practices to improve sheep welfare and reduce the cost of rib fractures to the sheep industry.

Background: Gingival enlargement is defined as an abnormal overgrowth of gingival tissues. A case of a 34–year–old female presenting with maxillary chronic inflammatory gingival enlargement associated with a nickel wire allergy is reported here. Replacement of the wire, good oral hygiene therapy and surgical therapy was carried out to provide a good aesthetic outcome. Histopathological evaluation was done of the excised specimen. There is only one similar case reported in literature to the best of our knowledge and ours is the second case. Result: A Histopathological diagnosis of inflammatory fibrous hyperplasia was established. No recurrence was reported at the end of 1 year. Conclusion: The patient should be made aware of the allergy at the initial visit and oral hygiene instructions should be reinforced at every visit. The significance of patient compliance during and following therapy as an important factor in the success of treatment.

Anion exchange membrane (AEM) electrolysis is hampered by two main issues: stability and performance. Focusing on the latter, this work demonstrates a highly active NiMo cathode for hydrogen evolution in AEM electrolysis. We demonstrate an electrolyzer performance of 1 A cm⁻² at 1.9 V (total cell voltage) with a NiMo loading of 5 mg cm⁻² and an iridium black anode in 1 M KOH at 50 °C, that may be compared to 1.8 V for a similar cell with Pt at the cathode. The catalysts developed here will be significant in supporting the pursuit of cheap and environmentally friendly hydrogen fuel.

This research aimed to establish the relationship between carbon-nitrogen nutritional factors and copper sulfate on laccase activity (LA) by Pleurotus ostreatus. Culture media composition was tested to choose the nitrogen source. Yeast extract (YE) was selected as a better nitrogen source than ammonium sulfate. Then, the effect of glucose and YE concentrations on biomass production and LA as response variables was evaluated using central composite experimental designs with and without copper. The results showed that the best culture medium composition was glucose 45 gL-1 and YE 15 gL-1, simultaneously optimizing these two response variables. The fungal transcriptome was obtained in this medium with or without copper, and the differentially expressed genes were found. Main up-regulated transcripts included three laccase genes (lacc2, lacc6, and lacc10) regulated by copper, whereas the principal down-regulated transcripts included a copper transporter (ctr1) and a regulator of nitrogen metabolism (nmr1). These results suggest that Ctr1, which facilitates the entry of copper in the cell, is regulated by nutrient-sufficiency conditions. Once inside, copper induces transcription of laccase genes. This finding could explain why a 10 to 20-fold increase in LA occurs with copper compared to cultures without copper when using the optimal concentration of YE as nitrogen sources.

The hydrogen evolution reaction (HER) has garnered attention to access sustainable energy generation with a pollutant-free combustion product in the form of H2 gas. Despite the utility of this pathway in the context of growing climate concerns, stable HER electrocatalysts which avoid the use of rare-earth platinum while retaining high catalytic performance and efficiency remains a challenge. In this work, we present the application of a binuclear nickel (II/III) Schiff base complex [Ni]2[L]2 2 for HER electrocatalysis. The design of the electrocatalyst provides optimal HER activity as the presence of electronegative heteroatoms in proximity to the metal centers augments proton affinity. As a result, the catalyst displays excellent HER activity with 100% faradaic efficiency (FE) at an onset potential of 0.4 V vs. reverse hydrogen electrode (RHE), sustained catalytic activity during prolonged electrolysis for greater than 17 hours, and provided a turn over number (TON) of 0.0006 s-1.

Urea, a prevalent component found in wastewater, shows great promise as an alternative substrate to water for energy-efficient hydrogen production by electrolysis. However, the sluggish kinetics of the anodic urea oxidation reaction (UOR) significantly hampers the overall reaction rate. To address this challenge, this article presents a comprehensive study focusing on the controlled fabrication of hierarchically structured nanomaterials as potential catalysts for UOR. The prepared MnO2@NiCo-LDH hybrid catalyst demonstrates remarkable improvements in reaction kinetics, benefiting from synergistic enhancements in charge transfer and efficient mass transport facilitated by its unique three-dimensional architecture. Notably, the catalyst exhibits an exceptionally low onset potential of 1.228 V and requires only 1.326 V to achieve an impressive current density of 100 mA cm-2, representing a state-of-the-art performance in UOR. These findings highlight the tremendous potential of this innovative material-designing strategy to drive advancements in electrocatalytic processes.

Abstract: Five patients with standard medical treatment-resistant symptoms of skin lesions, ear infections, allergic rhinitis, nasal congestion, asthma, heartburn, and failure to thrive were success- fully treated with an integrative medicine assessment and integrative medicine treatment approach. The integrative medicine assessment method of autonomic response testing enabled the identifica- tion of nickel sensitivity as a common element in these patients. It guided the use of the integrative medicine therapies of low dose immunotherapy, gamma linoleic acid supplementation, chelation, dietary nickel restriction, and removal of nickel containing dental and cosmetic appliances. A chart review of 151 patients indicated a strong association of nickel and the simultaneous presence of skin lesions.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

While there are extensive studies on the mineralogy and geochemistry of laterites worldwide, the temporal and spatial mineralogical development of a typical nickel laterite profile is still poorly constrained. In this study, we present a detailed mineralogical and geochemical characterization of samples systematically collected from a nickel laterite profile at the Sta. Cruz nickel laterite deposit, Zambales, Philippines, to describe the temporal and spatial development of the laterite profile. Wavelength-dispersive X-ray fluorescence spectroscopy (WDSXRF), mass balance-element mobility calculations, transmitted and reflected light microscopy, and previously reported results from coupled X-ray diffraction (XRD) and Rietveld refinement analyses, reveal that the laterite profile investigated is composed of two main horizons: the limonite and saprolite zones, separated by a thin transitional zone. The main zones are further subdivided into subzones based primarily on the mineral assemblage and major element chemistry: upper limonite, lower limonite, transitional zone, upper saprolite, and lower saprolite. Late-stage Ni-rich serpentine veins were observed cutting the upper and lower saprolite subzones. Investigation of the structure of goethite within the limonite zone via Rietveld refinement show that the crystallinity of goethite decreases with increasing Ni content and increasing crystallite size. This suggests that upwards through the limonite zone, as goethite ages, its crystallinity increases which possibly results in the removal of Ni from its crystal structure and eventual remobilization to the lower laterite zones. We propose a genetic model of the formation of the Sta. Cruz laterite consisting of four stages: (1) early-stage alteration, (2) continued serpentinization and volume expansion, (3) late stage serpentinization, dissolution, and incipient oxide formation, and (4) goethite ageing and Ni-rich serpentine vein formation. Overall, our results suggest that serpentinization is an important aspect of Ni laterite formation, both before and after the emplacement of the peridotite protolith.

In aqueous solution planar bis(1,2-dithiooxalato)nickelates(II), [Ni(dto)2]2- react with lanthanide ions (Ln3+) to form pentanuclear, hetero-bimetallic complexes of the general composition [{Ln(H2O)n}2{Ni(dto)2}3] · x H2O (n = 4 or 5; x = 9 - 12). Two complexes of this series, [{Pr(H2O)5}2{Ni(dto)2}3] · 11 H2O, Pr2Ni3 1 and [{Gd(H2O)5}2{Ni(dto)2}3] · 11 H2O, Gd2Ni3 2 were synthesized and characterized by single crystal X-ray structure analysis, X-ray powder diffraction, and IR spectroscopy. All Ln2Ni3 complexes crystallize as monoclinic crystals in the space group P21/c.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

Computational investigations on the BPE-ligated Cu-catalysed enantioselective addition of enynes to ketones were performed with DFT method. Two BPE-CuMes catalysts, BPE-CuMes and (S,S)-Ph-BPE–CuMes, were employed to probe the reaction mechanism with the emphasis on stereoselectivity. The calculations on the BPE-CuMes system indicate that the actvie metallized enyne intermediate acts as the catalyst for the catalytic cycle. The catalytic cycle involves two steps: 1) the ketone addition to the alkene moiety of the metallized enyne; 2) the metallization of enyne followed by the release of product with the recovery of the active metallized enyne intermediate. The first step accounts for the distribution of the products, and therefore is the stereo-controlling step in chiral systems. In the chiral (S,S)-Ph-BPE–CuMes system, the steric hindrance is vital for the distribution of products and responsible for the stereoselectivity of this reaction. The steric hindrance between the phenyl ring of the two substrates and groups at the chiral centers in the ligand skeleton is identified as the original of the stereoselectivity for the titled reaction.

Copper, the highly toxicity micronutrient, plays two essential roles: it is a catalytic and structural cofactor for Cu-dependent enzymes, and it acts as a secondary messenger. In the cells, copper is imported by CTR1, a transmembrane high-affinity copper importer, and DMT1 (divalent metal transporter). In cytosol, enzyme-specific chaperones receive copper from CTR1 C-terminus and deliver it to their apoenzymes. DMT1 cannot be a donor of catalytic copper because it does not have cytosol domain which is required for copper transfer to the Cu-chaperons and following to cuproenzymes. Here we assume that DMT1 can mediate copper way required for regulatory copper pool. To verify this thought, we used CRISPR/Cas9 to generate H1299 cell line with CTR1 or DMT1 single knockout (KO) and CTR1/DMT1 double knockout (DKO). To confirm KOs of the genes qRT-PCR were used. Two independent clones for each gene were selected for further studies. In CTR1-KO cells, expression of the DMT1 gene was significantly increased. In subcellular compartments, copper concentration decreased dramatically in DKO cells. CTR1-KO cells, but not DMT1-KO, demonstrated reduced sensitivity to cisplatin and silver ions, agents that enter the cell through CTR1. The expression of genes, whose protein products require copper: HIF1α, XIAP, COMMD1, CCS, Cp, but not SOD1 and NF-kB, changed their level. Perhaps these data will help to understand how the disturbances of copper homeodynamics lead to the development of neurodegenerative and oncological disorders. Possibility of using CTR1 KO and DMT1 KO cells to study homeodynamics of catalytic and signaling copper selectively is discussed.

This paper, the second in a series of two, describes the experimental results for removing arsenic from the dust collected in the electrostatic precipitators of a fluidized bed roasting oven (RP dust). The RP dust produced is discharged as a toxic waste, although its copper content is close to 20% by weight. This work aims to process the RP dust; until obtained a material with a low concentration of arsenic, which could be recirculated in smelting operations and recover the valuable metals. Based on the successful experience obtained in the first document with FS dust, this work proposes to use the reduction-sulphidation-volatilization processes to carry out the volatilization of arsenic from RP dust. A set of experiments was realized in the roasting different ratios of the mixture of copper concentrate / RP dust, sulfur / RP dust varying temperature and roasting time; to reach an arsenic concentration <0.5% by weight. The RP dust was characterized using different techniques, that confirmed more than 20% by weight of copper and describing its structure as a small particle agglomerate (<5 µm), with a complex sulfoxide morphology. The main results indicated: that for a 75/25 mixture of the copper concentrate / PR dust under 700 ° C, 15 minutes roasting time with air atmosphere, the arsenic volatilization was 96% by weight. Meanwhile, for a 5/95 mixture of sulfur / RP dust, at 650 ° C, the volatilization of arsenic was 67% by weight.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

The usage of biotechnological molecules and processes is an indispensable part of the resource technology research. The development of novel biomolecules therefore needs to be adapted to the existing applicational conditions and biological processes are to be examined. Novel biosorbents may not only contribute to future applications but can be of further used, e.g. to better understand the interaction of known metal- and metalloid-interacting biological molecules and materials. This review highlights biotechnological approaches published so far for bioremediation as well as metal recovery with a special spotlight on cobalt, nickel and arsenic.

Pt-coated Ni layer supported on Ni foam catalyst (denoted PtNi/Nifoam) was investigated for the oxidation of the formic acid (FAO) in acidic media. The prepared PtNi/Ni foam catalyst was studied as a function of the formic acid (FA) concentration at bare Pt and PtNi/Nifoam catalysts. The catalytic activity of the PtNi/Nifoam catalysts, studied on the basis of the ratio of the direct and indirect current peaks (jd)/(jnd) for the FAO reaction, showed values about 10 times higher compared to those on bare Pt, particularly at a low formic acid concentrations, reflecting the superiority of the former catalysts for the oxidation of FA to CO2. Ni foams provide a large surface area for the FOR while synergistic effects between Pt nanoparticles and Ni-oxy species layer on Ni foams contribute significantly to the enhanced oxidation of FA via the direct pathway, making it almost equal to the indirect pathway, particularly at low formic acid concentrations.

The Ni-laterite deposit at the San Felipe plateau, located 30 km northwest of Camagüey, in cen-tral Cuba, is the best example of a clay-type deposit in the Caribbean region. San Felipe resulted from weathering of mantle peridotites of the Cretaceous Camagüey ophiolites. In this study, a geochemical and mineralogical characterization of two profiles (83 and 84) from the San Felipe deposit has been performed by XRF, ICP-MS, quantitative XRPD, oriented aggregate mount XRD, SEM, FE-SEM and EMPA. Core 83 with a length of 23 m, and drilled in the central part of the plateau, presents a notable concentration of cryptocrystalline quartz fragments and a rather poor content in NiO, averaging 0.87% wt. Core 84, which is 12 m long, and drilled at the border of the plateau, lacks silica fragments and presents a higher NiO content, averaging 1.79 %wt. The smectite structural formulae reveal that they evolve from trioctahedral to dioctahedral towards the top of the laterite profiles. Quantitative XRD analyses indicate that smectite is a dominant Ni bearing phase, accompanied by serpentine and minor chlorite. Serpentine, as smectite, is en-riched in the less soluble elements Fe3+, Al and Ni towards the top of the profiles. Core 83 seems to have been affected by collapses, replenishments, whereas core 84 may have remained undis-turbed.

Within the study, magnetic/polyetherimide-acrylonitrile composite nanofibers membrane with effective adsorption of nickel ions in aqueous solution were established, through a simple electrospinning method. Iron oxide nanoparticles were stirred and ultrasonically dispersed into polyetherimide-acrylonitrile solution for homogenous suspension. Afterwards, the polyetherimide-acrylonitrile solution with uniform suspension of iron nanoparticles was used in electrospinning machine to produce uniform and smooth nanofibers composite membrane. The confirmation of nanoparticles incorporation into polymeric membrane were characterized by SEM, EDX, FTIR, XRD and nanoparticles aqueous stability through leach out test. The high adsorption capability of the composite membranes on nickel ions was mainly attributed to the combination of magnetic nanoparticles, polyetherimide-acrylonitrile matrix and nano-sized structure of membrane. Membrane containing magnetic nanoparticles demonstrate the maximum adsorption capabilities (102 mg/g) for nickel ions from aqueous solution. Different kinetics and isotherm models were applied to understand the adsorption behavior during adsorption process, amongst them pseudo second order kinetic and Langmuir isotherm model were well fitted. Additionally, EDX, FTIR and XRD results confirmed the presence of nickel ions onto membrane after adsorption process. Polyetherimide-acrylonitrile composite nanofibers membranes containing magnetic nanoparticles may use as an environmentally-friendly and non-toxic adsorbent for the removal of nickel ions in aqueous medium due to its ease of preparation, easy to use and stability in aqueous medium by retaining the nanoparticles inside the nanofibers membranes.

Results are presented concerning the influence on the water splitting process of enantiopure tartaric acid present in bulk solution. Stainless steel and electrodeposited nickel are used as working electrode (WE) surface. The latter is obtained by electrodeposition on the two poles of a magnet. The influence and role played by the chiral compound in solution has been assessed by comparing the current values, in cyclic voltammetry (CV) experiments, recorded in the potential range at which oxygen evolution reaction (OER) occurs. In the case of tartaric acid and nickel WE a spin polarization of about 4 % is found. The use of the chiral environment (bulk solution) and ferromagnetic chiral Ni electrode allows for observing the OER at a more favourable potential: about 50 mV (i.e. a cathodic, less positive, shift of the potential at which the oxygen evolution is observed).

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

The accumulation of microorganisms, plants, algae, or small animals on wet surfaces that have a mechanical function causes biofouling, which can result in structural or other functional deficiencies. The maritime shipping industry must constantly manage biofouling to optimize operational performance, which is a common and long-lasting problem. It can occur in any metal structure in contact or submerged in ocean water, which represents additional costs in terms of repairs and maintenance. This study is focused on the production of antifouling coatings, made with nanoparticles of copper selenide (CuSe) modified with gum arabic, within a water-base acrylic polymeric matrix. During the curing of the acrylic resin, the CuSe NPs remain embedded in the resin but this does not prevent the release of ions. The coatings presented to release copper and selenium ions for up to 80 days, selenium was the element that was released the most. The adhesion of film coatings to metallic substrates showed good adhesion, scale 5B (ASTM D3359 standard). Antimicrobial activity tests show that the coatings have an inhibitory effect on Escherichia coli and Candida albicans. The effect being more noticeable when the coating is detached from the substrate and placed on a growing medium, than compared to the coating on a substrate. Scanning electron microscopy (SEM) observations show that nanostructured CuSe coatings are made up of rod-shaped and spherical particles whose range ranges from 12 to 25 nm. The Energy Dispersive X-ray spectroscopy (EDS) studies showed that the ratio of selenium nanoparticles is greater than that of copper and that their distribution is homogeneous

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

The study of the inherent factors that influence the isolation of one type of metallosupramolecular architecture over another is one of the main objectives in the field of Metallosupramolecular Chemistry. In this work, we report two new neutral copper(II) helicates, [Cu2(L1)2]·4CH3CN and [Cu2(L2)2]·CH3CN, obtained by means of an electrochemical methodology and derived from two Schiff-based strands functionalized with ortho- and para-t-butyl groups on the aromatic surface. These small modifications let us to explore the relationship between the ligand design and the structure of the extended metallosupramolecular architecture. The magnetic properties of the Cu(II) helicates were explored by EPR spectroscopy and DC magnetic susceptibility measurements.

The development of oxidation processes with generating powerful radicals is the most interesting and thought-provoking dimension of peroxymonosulfate (PMS) activation. In this study, a magnetic spinel CuFe2O4 was successfully prepared by a facile, non-toxic, cost-efficient co-precipitation method with the synergetic effect of photocatalytic PMS oxidation against recalcitrant benzotriazole (BTA) pollutant. The high particle dispersion and large surface area (201.898 m2/g) provided a high photocatalytic activity with CuFe2O4. The obtained results from the central composite design (CCD) analysis confirmed the optimum degrading rate of BTA reached 81.4% at the optimum operational condition of CuFe2O4= 0.4 g/L, PMS= 2 mM, BTA= 20 mg/L after 70 min irradiation time. As such, the active species capture experiments revealed the presence of •OH, SO4•‒, O2•‒ and h+ species in CuFe2O4/UV/PMS system where SO4•‒ was dominated for BTA photodegradation. The combination of photocatalysis and PMS activation enhanced the consumption of metal ions in redox cycle reactions, thus preventing metal leaching and maintain the recyclability with reasonable mineralization efficiency which achieved more than 40% total organic carbon removal after four batch experiments. A retardant effect on BTA oxidation was observed with comparing the water’s common anion constituents as HCO3‒ > Cl‒ > NO3‒ > SO2‒. Results from intermediates identification showed that the transformation pathway of BTA developed as the deprotonation, hydrolysis and ring cleavage processes promoting the practical potential of photo-absorbing CuFe2O4 catalyzed PMS which can be a promising method due to convenient magnetic separation form the solution.

Metal bioaccumulation and metallothionein (MT) expression were investigated in gills and liver of the red-blooded Antarctic teleost Trematomus hansoni with the aim to evaluate the possibility for this species to face, with adequate physiological responses, an increase of copper or cadmium concentrations in the environment. Specimens of this Antarctic fish were collected from Terra Nova Bay (Ross Sea) and used for a metal exposure experiment in controlled laboratory condi-tions. The two treatments lead to a significant accumulation of both metals and an increase of gene transcription only for the MT-1. The biosynthesis of MTs was verified especially in speci-mens exposed to Cd, but the majority of these proteins were soon oxidized, probably because they were involved in cell protection against the risk of oxidative stress, by reactive oxygen spe-cies scavenging. The obtained data highlighted the phenotypic plasticity of T. hansoni, a species evolved in an environment characterized by natural high concentrations of Cu and Cd, and maybe the possibility for the Antarctic fish to face the challenges of a world that is becoming every day more toxic.

In the human body, Copper (Cu) is a major and essential player in a large number of cellular mechanisms and signaling pathways. The involvement of Cu in oxidation-reduction reactions requires close regulation of copper metabolism in order to avoid toxic effects. In many types of cancer, variations in copper protein levels have been demonstrated. These variations result in increased concentrations of intra-tumoral Cu and alterations in the systemic distribution of copper. Such alterations in Cu homeostasis may promote tumor growth or invasiveness, or even confer resistance to treatments. Once characterized, the dysregulated Cu metabolism is pinpointing several promising biomarkers for clinical use, with prognostic or predictive capabilities. The altered Cu metabolism in cancer cells and the different responses of tumor cells to Cu are strongly supporting the development of treatments to disrupt, deplete or increase Cu levels in tumors. The metallic nature of Cu, as a chemical element, is key for the development of anticancer agents via the synthesis of nanoparticles or copper-based complexes with antineoplastic properties for therapy. Finally, some of these new therapeutic strategies such as chelators or ionophores have shown promising results in a preclinical setting, while others are already in the clinic.

Predicting copper price is essential for making decisions that can affect companies and governments dependent on the copper mining industry. Copper prices follow a time series that is non-linear, non-stationary, and which have periods that change as a result of potential growth, cyclical fluctuation and errors. Sometimes the trend and cyclical components together are referred to as a trend-cycle. In order to make predictions, it is necessary to consider the different characteristics of trend-cycle. In this paper, we study a copper price prediction method using Support Vector Regression. This work explores the potential of the Support Vector Regression with external recurrences to make predictions at 5, 10, 15, 20 and 30 days into the future in the copper closing price at the London Metal Exchanges. The best model for each forecast interval is performed using a grid search and balanced cross-validation. In experiments on real data-sets, our results obtained indicate that the parameters (C, ε, γ) of the model Support Vector Regression do not differ between the different prediction intervals. Additionally, the amount of preceding values used to make the estimates does not vary according to the predicted interval. Results show that the support vector regression model has a lower prediction error and is more robust. Our results show that the presented model is able to predict copper price volatilities near reality, being the RMSE equal or less than the 2.2% for prediction periods of 5 and 10 days.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Mining is one of the main economic activities of several developing countries as Chile. Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased that has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium and rare earth elements. This transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid-liquid separation that allows the processing of solutions with low concentrations of metals corresponds to the adsorption, and more recently the biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in the different types of biomass. Bacterial, fungal, plant and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit in the north of Chile and after an acid leaching copper was biosorbed, for which the kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH and initial metal concentration were studied.

This article presents the copper ions adsorption process using an activated carbon from winemaking wastes. The pH, temperature, activated carbon amount and initial copper concentration were varied based on a full factorial 2^k experimental design. Kinetic and thermodynamic studies were also carried out. The adsorption kinetics was found follow a pseudo-second-order model. The adsorption data fit better to the Langmuir isotherm. The ANOVA demonstrated that both pH of the solution and activated carbon dosage had the greatest influence on copper adsorption. The activation energy was -32 kJ·mol^-1 suggesting that the copper adsorption is a physic-sorption process. The best fit to a linear correlation was the moving boundary equation that controls the kinetics for the adsorption copper ions onto the activated carbon. The X-ray photoelectron spectroscopy (XPS) results reveal the existence of different copper species (Cu²⁺, Cu⁺ and or Cu⁰) on the surface of the carbonaceous adsorbent after the adsorption, which could suggest a simultaneous reduction process.

One of the largest in the archipelago silver-copper mineralisation at Mount Sigurdf′ellet in West Spitsbergen Island was found in 1990 by Russian geologists. Firstly genesis was caused exclusively with hydrothermal ore migration of a substance from the enclosing sandstone and siltstone of the Devonian age. But subsequent work on the ore and nearest rocks of the basement gave a new factual material on the geochemical characteristics of potential sources of metals and found new for this mineral occurrence - gold mineralization. Similarity of geochemical associations of Sigurd ore occurrence with nearby upper Proterozoic marble as the first likely source of ore substance and the second - caused by carbonate-containing streaks in Low Devonian sediments. Ore-formation, probably due to repeated hydrothermal processes and was completed in a period of tectono-magmatic activity in Jurassic-Cretaceous time.

In this study, the corrosion performances of ammonium copper quat (ACQ) and boric acid (BA) wood preservatives were investigated, with micronized copper quat (MCQ) and nano boron (NB) used as reference materials. In the study, Scots pine (Pinus sylvestris L.) wood samples were impregnated according to the full-cell process method with ACQ at 2.4% concentration, BA at 4% and MCQ and NB at 1%. The ACQ- and BA-impregnated samples were then impregnated for a second time using five different water-repellent materials: tall oil, linseed oil, sodium silicate, methyl hydrogen silicone and N'-N- (1, 8-Naphthalyl) hydroxylamine. Polyethylene glycol (PEG) 600 and aluminum sulfate were introduced as single impregnations in the form of homogeneous mixtures with the ACQ and BA. The corrosion properties of the impregnated and control samples, including metal weight loss (MWL) and corrosion depth, were examined. As a result, the MWL values of the ACQ-impregnated samples showed an increase compared to the control group. The MWL values of the MCQ-impregnated samples were lower than those of the samples impregnated with ACQ, whilst the MWL values of the BA-impregnated samples were higher than those of the samples impregnated with NB.

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

There is currently much interest in avoiding precious metals in Catalysis. The devel-opment of nickel catalysts to replace palladium in the Mizoroki-Heck reaction is a relevant case in this line of research since both elements share many chemical features. This contri-bution focuses on -Phenyl elimination in alkylnickel complexes. This is the microscopic reverse of olefin insertion (or carbometallation), a fundamental step of the Heck cycle that is usually considered irreversible and selectivity-determining. However, the potential reversibil-ity of carbometallation is generally concealed by the facile beta-hydrogen elimination that follows. Where -hydrogen elimination is hindered, beta-aryl elimination may ensue. We have previously shown that cationic 2-methyl-2-phenylpropyl (neophyl) palladium com-plexes supported by bidentate ligands experience -Ph elimination, which can be seen as an example of olefin de-insertion. In this contribution, we report that -phenyl elimination can also occur in their nickel analogs, in which case fast hydrolyses of the resulting phenyl product can follow the reaction. We investigated the mechanism of these processes and compared their feasibility for nickel and palladium catalysts using DFT calculations. These results are relevant information for the design of nickel-based catalysts for the Heck reac-tion.

This manuscript presents the result of utilizing cellulose as a template to prepare na-nosized WO3-NiWO4 and its application as co-catalysts in Pt/WO3-C and Pt/WO3-NiWO4-C for ethanol and glycerol electro-oxidation. Microcrystalline cellulose was hydrolyzed with phosphotungstic acid (H3PW12O40) to prepare the nanosized template of crystalline cellulose. Next, the template was impregnated with Ni(NO3)2, rendering a precursor mate-rial that is subsequently air-calcinated, removing the carbon-template material to obtain the nanometric WO3 and NiWO4. Elemental analysis confirmed the coexistence of nickel and tungsten, whereas the thermal analysis evidenced the high thermal stability of these materials. The X-ray diffractograms displayed crystal facets of WO3 and, when added Ni, of NiWO4. The transmission electron micrographs corroborated the formation of na-nosized particles with average particle sizes close to 50 nm. Finally, to apply this material, Pt/WO3-C and Pt/WO3-NiWO4-C were prepared and used in ethanol and glycerol electro-oxidation in alkaline medium, observing a promotional effect of the oxide and tungstate by reducing the onset potential and increasing the current density. These materials show great potential to produce clean electricity or green hydrogen contributing to energetic transition.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Copper oxide nanoparticles (CuONPs) were synthesized using an eco-friendly method and their antimicrobial and biocompatibility properties were determined. The supernatant and extract of the fungus Ganoderma sessile yielded small, quasi-spherical NPs with an average size of 4.5 ± 1.9 nm and 5.2 ± 2.1 nm, respectively. CuONPs showed antimicrobial activity against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Minimum inhibitory concentration (MIC) for E. coli and S. aureus was 15.9 µg/mL for nanoparticles (NPs) using the supernatant (CuONPs-S) and 16.5 µg/ml for NPs using the extract (CuONPs-E). Lower concentrations were required for P. aeruginosa inhibition. Ultrastructural analysis revealed the presence of the small CuONPs all through the bacterial cells. Finally, the toxicity of CuONPs was analyzed in three mammalian cell lines: hepatocytes (AML-12), macrophages (RAW 264.7) and kidney (MDCK). Low concentrations (<15 µg/ml) of CuONPs-E were non-toxic to kidney cells and macrophages, and the hepatocytes were the most susceptible to CuONPs-S. The results obtained suggest that the CuONPs synthesized using the extract of the fungus G. sessile, could be further evaluated for the treatment of superficial infectious diseases.

The first single crystal structure of the homoleptic copper (II) ML2 complex (M=Cu (II), L=curcumin) was obtained and its structure was elucidated by X-ray diffraction showing a square planar geometry. The supramolecular arrangement is supported by C-H···O interactions and the solvent (MeOH) plays an important role in stabilizing the crystal packing. The cytotoxic activity of the complex against six cancer cell lines substantially surpasses that of curcumin itself, and it is particularly selective against leukemia (K562) and human glioblastoma (U251) cell lines with similar antioxidant activity to BHT. This constitutes the first crystal structure of pristine curcumin complexed with a metal ion.

Organic Coatings have potential applications in the prevention of metal corrosion in an aqueous solution. The protective effect of SEBS coated copper corrosion in NaCl 3% solution was investigated by using electrochemical methods. The main objective of this work is to find the optimal conditions of the protocol immersion to evaluate the effects of SEBS ratio and two-immersion time on the anticorrosive behaviour of copper in 3 wt % NaCl solution in order to determine the best conditions to produce a protective SEBS film on the copper surface. Response Surface Methodology (RSM) is used as an optimization method. The study’s findings show the combination of three environmental factors that minimize corrosion rate. The Box-Behnken Design (BBD) is working perfectly for the statistical significance of the model (ANOVA test). This analysis calculates the contribution value of each parameter in changing the value of the corrosion rate (CR) in not only individual but also synergistic cases. The optimized parameters were found to be a 2.17% of SEBS ratio, 20 min of immersion 1, and 21 min of immersion 2. The electrochemical impedance spectroscopy tests confirmed the results.

Abstract Purpose Since their introduction, intrauterine devices (IUDs) have been associated with various complications. Avery rare complication is the perforation of the cervix by the strings of the IUD. Purpose of the current study is to present a novel case of cervical perforation by the strings of a copper IUD and to perform a systematic review of the literature. Materials and Methods The patient a 43-year-old attended the gynecology clinic in order to remove her copper IUD. Speculum examination revealed that both the strings of the IUD perforated the anterior lip of the cervix. Management options were offered, the patient opted for a hysteroscopic removal. We searched the electronic databases: MEDLINE, Cochrane Library,Google Scholar,EBSCO for similar cases. Results Electronic search yielded 1821 articles; 8 were selected for inclusion. Mean age of the women was 35,37±7,781, range (26-47) years. One woman (12.5%) was nulligravida;3 women were multigravida (37,5%). Seven women (87,5%) were asymptomatic. Three IUDs (37,5%) were LNG-IUS; 5 IUDs (62,5%) contained copper. Conclusions Cervical perforation by the strings of IUD is an extremely rare clinical entity. It is asymptomatic in general and in most cases the strings of the IUD may be returned back to the endocervical canal after surgical maneuvers.

Copper toxicity has been a selective pressure on the sea-ice bacteria due to its widespread occur-rence in Antarctica. Here, with a combined biochemical and metabolomic approach, the Cu2+ ad-aptation mechanisms of Antarctic bacteria were analyzed. Heavy metal resistance pattern of Pb2+ > Cu2+ > Cd2+ > Hg2+ > Zn2+ was observed. Copper treatment did increase the activity of antioxidants and enzymes, maintaining cellular redox state balance and normal cell division and growth. Metabolomics analysis demonstrated that fatty acids, amino acids, and carbohydrates played dominant roles in copper stress adaptation. The results indicated that the adaptation mechanisms of strain O5 to copper stress included protein synthesis and repair, accumulation of organic per-meable substances, up-regulation of energy metabolism, and formation of fatty acids. This study increases the resistance mechanism understanding of Antarctic strains to heavy metals in extreme environments.

Long-term changes in nanoparticles of copper-silver bimetallic systems on natural clinoptilolite obtained by ion exchange of Cu2+ and Ag+, and then reduced at different temperatures, have been studied. Even after storage under ambient conditions, XRD and UV-Vis diffuse reflectance spectra indicate the presence of nanospecies of reduced copper and silver. Scanning Electron Microscopy of aged bimetallic samples, reduced at the highest temperature (450oC) and the primary samples for their preparation, also aged, showed the presence of silver nanoparticles with a size of about 100 nm. They are formed in the initial ion-exchanged sample (without reduction) due to the degradation of Ag+ ions. The nanoparticles in the reduced sample are larger; in both samples they are evenly distributed over the surface. The presence of silver affects the stability and the mechanism of decomposition/oxidation of reduced copper nanospecies, and this stability is higher in bimetallic systems. The decomposition pattern of recently reduced species includes the formation of smaller nanoparticles and few-atomic clusters. This can occur, preceding the complete oxidation of Cu to ions. Quasi-colloidal silver, which is present in fresh bimetallic samples reduced at lower temperatures, transforms after aging into Ag8 clusters, which indicates the stability of these nanospecies on natural clinoptilolite.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

Preeclampsia (PE) is characterized by a series of clinical features such as hypertension and proteinuria associated with endothelial dysfunction and the impairment of placenta vascular endothelial integrity. This study aimed to investigate the effect of serum copper (Cu) level on some angiogenesis-related factors including vascular endothelial growth factor-A (VEGF-A), soluble Fms-like tyrosine kinase-1 (sVEGF-R1), soluble endoglin (sEng) and cerruloplasmin (Cp) in Iraqi women with preeclampsia (PE) and control pregnant women. Therefore, 60 women with PE in addition to 30 healthy pregnant women were enrolled in the study. Serum concentration of sEng, VEGF-A, sVEGF-R1, and Cu in PE group significantly increased (p<0.05) in the PE group compared with that in the control group. Increased production of antiangiogenic factors, soluble VEGF-A and sEng contribute to the pathophysiology of PE, indicating the involvement of these parameters in the angiogenic balance in patients with PE. Tests for between-subject effects showed that the circulating angiogenesis factors and Cu were significantly associated with the presence of PE. Serum Cu level was significantly correlated with VEGF- A and VEGF-R1 levels but not with sEng. Multiple regression analysis revealed that only Cp and BP can significantly predict the complications in women with PE. In conclusion, serum Cu has a role in the angiogenesis in women with PE and may be a new drug target in the prevention or treatment of PE.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

CuO-ZnO-Al2O3 catalysts are designed for the low-temperature shift conversion in the process of hydrogen and ammonia synthesis gas production. The paper presents the results of research on recovery of copper and zinc from spent catalysts using pyrometallurgical and hydrometallurgical methods. Under reducing conditions, at high temperature, having appropriately selected the composition of the slag, more than 66% of copper in metallic form and about 70% of zinc in the form of ZnO can be extracted from this material. Hydrometallurgical processing of the catalysts was carried out using two leaching solutions: alkaline and acidic. Almost 62% of the zinc contained in the catalysts has been leached to the alkaline solution and about 98% of copper has been leached to the acidic solution. After the hydrometallurgical treatment of the catalysts, insoluble residue was also obtained in the form of pure ZnAl2O4. This compound can be reused to produce catalysts, or it can be processed under reducing conditions at high temperature to recover zinc. The recovery of zinc and copper from such a material is consistent with the policy of sustainable development and helps to reduce the environmental load of stored wastes.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

This article reports the two-step synthesis of NiFeO_x nanomaterials, their characterisation and bifunctional electrocatalytic activity measurements in alkaline electrolyte for metal-air batteries. The samples were mostly in layered double hydroxide at the initial temperature, but upon heat treatment, they were converted to NiFe₂O₄ phases. The electrochemical behaviour of the different samples was studied by linear sweep voltammetry and cyclic voltammetry on the glassy carbon electrode. The OER catalyst activity was observed for low mass loadings (0.125 mg cm⁻²), whereas high catalyst loading exhibited the best performance on the ORR side. The sample heat treated at 250 °C delivered the highest bi-functional oxygen evolution and reduction reaction activity (OER/ORR) thanks to its thin-holey nanosheet like structure with higher nickel oxidation state at 250 °C. This work further helps to develop low-cost electrocatalyst development for metal-air batteries.

The present study aimed to investigate the effect of cold deformation on the precipitation kinetics of a binary CuSc alloy containing 0.4 wt.% scandium using the experimental analysis method of differential scanning calorimetry (DSC). Non-deformed and 75% cross-section reduced cold-rolled, supersaturated specimens were tested at non-isothermal DSC runs at up to five different heating rates. The DSC results showed that cold deformation significantly accelerated the precipitation process in the binary alloy, leading to a decrease in the initial and peak temperatures of the exothermic reactions. The activation energies calculated with the Kissinger method, indicated that the precipitation activation energy decreased with increasing cold deformation. The findings of this study provide worthy implications to further optimize the processing of Cu-Sc alloys with improved mechanical properties.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

The dopamine and uric acid are primary products of purine metabolism and they coexist in serum and the extracellular fluid of the central nervous system. Some diseases of the human body are due to abnormal levels of uric acid and dopamine. Thus, the clinical diagnosis of some diseases needs a sensitive and simultaneous analysis of uric acid and dopamine. In this study, a novel conductive composite film containing multi-walled carbon nanotubes (MWTs) with cooper phthalocyanine attached to acrylate polymer (MWCNTs-CuMAPC-PnBA) was fabricated and dropped on a glassy carbon electrode and used for the simultaneous determination of Uric Acid (UA) and dopamine (DA). The modified glassy carbon electrode showed satisfactory electrocatalytic activity toward dopamine and uric acid. Low detection limits were achieved at 0.174 µM of DA and 6.87 µM of UA and the linear detection ranges of DA and UA are 5-200 µM and 20-250 µM respectively. The proposed sensing system based on the modified GCE offers promising results for rapid, cost-effective and selective simultaneous detection of uric acid and dopamine. Also, the complex modified electrode showed satisfactory results to detecting simultaneously UA and DA in real human samples (human Urine) via the standard addition method.

Aryl chlorides and bromides in the presence of NHC palladium hydroxo dimers of the type [{Pd(µ-OH)Cl(NHC)}2] (where NHC = IPr, SIPr, IMes, SIMes) undergo an efficient and selective Sonogashira cross-coupling with terminal acetylenes. For the coupling of 4-chlorotoluene with phenylacetylene TON = 560000 was observed. The procedure enables high-throughput and selective synthesis of a broad spectrum of unsymmetrically substituted 1,2-diarylacetylenes. Nearly a quantitative amount of HCl was detected within cross-coupling products. Water plays the role of the base and is regenerated in the process so that it does not have to be used in stoichiometric amounts (relative to the limiting reactant). Generation of the active Pd(0) complex proceeds via ethanol oxidation.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Copper nitride (Cu3N), a metastable semiconductor material, but with reasonably-high-stability at room temperature, is drawing a great deal of attention as a very promising next-generation, earth-abundant, thin-film solar absorber. Its non-toxicity, on the other hand, makes it a very attractive eco-friendly semiconducting material. In the present work, Cu3N thin films were grown by employing radio-frequency magnetron sputtering, at room temperature, with 50-W RF-power, and partial nitrogen pressures of 8.0 and 1.0, onto glass substrates. Thus, the influence of argon on the optical properties of the Cu3N thin films was studied, with the goal of being able to achieve a low-cost, light absorber material, with appropriate properties in order to substitute the more conventional silicon, in photovoltaic cells. Variable-angle spectroscopic ellipsometry measurements have been conducted at three angles, 50∘, 60∘, and 70∘, respectively, in order to obtain the two ellipsometric parameters psi, ψ, and delta, Δ, respectively. For the constructed optical model, the bulk planar Cu3N layer is described by a one-dimensional graded-index model, combine with the mixture of a Tauc-Lorentz oscillator and up to four Gaussian oscillators, whereas a BEMA model with 50%-air-void is adopted in order to account for the existing surface-roughness layer. In addition, the optical properties such as the energy-band gap, and refractive index and absorption coefficient, were determined in order to assess the actual capability of this material as a light absorber for solar cells. The direct and indirect band gap energies were accurately calculated, and they were found to be in the ranges of 2.14-2.21 eV and very clse to 1.50 eV, respectively.

The metal chelator PBT2 (5,7-dichloro-2-[(dimethylamino)methyl]-8-hydroxyquinoline) acts as a terdentate ligand capable of forming binary and ternary Cu2+ complexes. It was clinically trialed as an Alzheimer’s disease (AD) therapeutic but failed to progress beyond phase II. The β-amyloid (Aβ) peptide associated with AD was recently concluded to form a unique Cu(Aβ) complex that is inaccessible to PBT2. Herein, it is shown that the species ascribed to this binary Cu(Aβ) complex in fact corresponds to ternary Cu(PBT2)NIm[Aβ] complexes formed by anchoring of Cu(PBT2) on imine nitrogen (NIm) donors of His side chains. The primary site of ternary complex formation is His6, having a conditional stepwise formation constant at pH 7.4 (K [M−1] ) of log K = 6.4 ± 0.1, and a second site is supplied by His13 or His14 (log K = 4.4 ± 0.1). The stability of Cu(PBT2)NIm[H13/14] is comparable with that of the simplest ternary complexes involving free imidazole (log K = 4.22 ± 0.09) and histamine (log K = 4.00 ± 0.05). The 100-fold larger formation constant for Cu(PBT2)NIm[H6] indicates that outer-sphere ligand–peptide interactions strongly stabilize its structure. Despite the relatively high stability of Cu(PBT2)NImH6, PBT2 is a promiscuous Cu2+-binding ligand capable of forming a ternary Cu(PBT2)NIm complex with any ligand containing NIm donor. These ligands include histamine, L-His, and ubiquitous His side chains of peptides and proteins in the extracellular milieu, whose combined effect should outweigh that of a single Cu(PBT2)NIm[H6] complex regardless of its stability. We therefore conclude that PBT2 is capable of accessing Cu(Aβ) complexes with high stability but not specificity. The results have implications for future AD therapeutic strategies and understanding the role of PBT2 in the bulk transport of transition metal ions. Given the repurposing of PBT2 as a drug for breaking antibiotic resistance, ternary Cu(PBT2)NIm and analogous Zn(PBT2)NIm complexes may be relevant to its antimicrobial properties.

This work aimed to carry out a bioremediation study to evaluate the resistance of Penicillium sp. isolated from kefir grains for the treatment of copper. The fungal culture medium was prepared using a 2% malt-agar medium at pH 7.0 in which Penicillium sp. was inoculated. Penicillium sp. growing in a liquid medium showed a decrease in biomass in presence of Cu(NO3)2 (800 mg.L-1), suggesting that the metal impacts the growth rate of the fungus. Moreover, the combined factors of pH and the presence of the inorganic contaminant impacted the radial growth of the fungus, causing inhibition of 73% at pH 4.0, 75% at pH 7.0, and 77% at pH 9.0 in liquid medium compared to control. However, images obtained with scanning electron microscopy showed the integrity of the fungus cell, even at high doses of copper in the medium. Therefore, it can be concluded that Penicillium sp. isolated from kefir grain can bioremediate the environment and that the harmful effects of heavy metals can be minimized as a result biosorption. Although the growth of Penicillium sp. is inhibited, such retardation requires high doses of copper nitrate, thus ensuring the use of this microorganism for protection against the harmful effects of non-essential copper in the environment.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate

Doped copper overpacks are planned to be utilized in the spent nuclear fuel repositories in Finland and in Sweden. The assessment of long-term integrity of the material is a matter of importance. Grain structure variations, segregation and any possible manufacturing defects in microstructure are relevant in terms of susceptibility to creep and damage from the loading evolution imposed by its operating environment. This work focuses on studying the microstructure level length-scale dependent deformation behavior of the material, of particular significance with respect to accumulation of plasticity over the extensive operational period of the overpacks. Reduced micromorphic crystal plasticity model, which is similar to strain gradient models, is used in this investigation. Firstly, the model’s size dependent plasticity effects are evaluated. Secondly, different microstructural aggregates presenting overpack sections are analyzed. Grain size dependent hardening responses, i.e., Hall-Petch like behavior, can be achieved with the enhanced hardening associated with the micromorphic model at polycrystalline level. It was found that the nominally large grain size in the base material of the overpack shows lower strain hardening potential than the fine grained region of the welded microstructure with stronger strain gradient related hardening effects. Size dependent regularization of strain localization networks is indicated as a desired characteristics of the model. The findings can be utilized to provide an improved basis for modeling the viscoplastic deformation behavior of the studied copper alloy and assess the microstructural origins of any integrity concerns explicitly by way of full field modeling.

Friction stir alloying (FSA) of commercially pure Cu with Ni, Zn, and Mg is implemented in the current study. The successfully fabricated alloy structure has been scrutinized in terms of mechanical and micro-structural standpoints. Energy-dispersive X-ray spectroscopy revealed a uniform distribution of alloying elements and coalescence at the atomic level. The compositional and grain size heterogeneity is managed in the stir zone, which pave way for microstructural control using FSA. Thus, the present study carries significance for the development of novel materials whose fabrication requires temperature far below the melting point of base metals. Ultra-refinement of grains is found to accompany the alloying process, with ~ 440 nm being the smallest grain size. Maximum and average micro-hardness enhancement of 18.4 % and 6 % is observed for the fabricated alloy. Tensile properties have also been investigated and co-related with the micro-structural morphology. The shift towards grain bimodality has also been reported, which is a highly sought property in the present day, especially to overcome the strength-ductility trade-off.

Mitigation of Anthropogenic CO2 emissions possess a major global challenge for modern societies. Herein catalytic solutions are meant to play a key role. Among the different catalysts for CO2 conversion Cu supported on molybdenum carbide is receiving increasing attention. Hence, in the present communication we show the activity, selectivity and stability of fresh-prepared -Mo2C catalysts and compare the results with those of Cu/Mo2C, Cs/Mo2C and Cu/Cs/Mo2C in CO2 hydrogenation reactions. The results showed that all the catalysts were active and the main reaction product was methanol. The results showed that copper-cesium and molybdenum effectively interact and that cesium promoted the formation of metallic Mo. While, the incorporation of copper is positive to improve the activity and selectivity to methanol, the presence of Mo0 phase was detrimental for the conversion and selectivity. Moreover, the catalysts promoted by cesium underwent redox surface transformations during the reaction that diminished their catalytic performance. The molybdenum phase in Cu/Mo2C changes during reaction leading to metallic molybdenum and tuning the catalytic activity.

Copper, which can potentially be a highly toxic agent, is an essential nutrient due to its role as a co-factor for cuproenzymes and participation in signaling pathways. In mammals, the liver is a central organ that controls copper turnover throughout the body: copper absorption, distribution, and excretion. In ontogenesis, there are two types of copper metabolism: embryonic and adult, which maintain the balance of copper in each of these periods, respectively. In the liver cells, these types are characterized by specific expression patterns and activity levels of the genes encoding ceruloplasmin, which is the main extracellular ferroxidase and copper transporter and proteins mediating ceruloplasmin metalation. In newborns, the molecular-genetic mechanisms responsible for copper homeostasis and the ontogenetic switch from embryonic to adult copper metabolism are highly adapted to milk ceruloplasmin as a dietary source of copper. In the mammary gland cells, the level of ceruloplasmin gene expression and the alternative splicing of its pre-mRNA govern the amount of ceruloplasmin in milk, and thus, the amount of copper absorbed by the newborn is controlled. In the newborns, absorption, distribution, and accumulation copper are adapted to milk ceruloplasmin. In the newborns, which are not breast-fed at the early stages of postnatal development, the control for alimentary copper balance is absent. We tried to focus on the neonatal consequences of a violation of the balance of copper in the mother / newborn system. Although there is still much to be learned, the time to pay attention to this problem came because the neonatal misbalance of copper may provoke the development of copper related disorders for future life.

A novel and simple method to improve the corrosion resistance of copper by constructing a 3D 1-dodecanethiol self-assembled monolayers (SAMs) in 3.5% NaCl solution is reported in this study. Several drops of 1% H3PO4 solution are thinly and uniformly distributed on copper surface to form a 3D nanostructure constituted by Cu3(PO4)2 nanoflowers. The anticorrosion properties of 1-dodecanethiol SAMs on copper surface and on copper surface treated with H3PO4 solution were evaluated. Results demonstrated that 1-dodecanethiol SAMs on bare copper surface exhibit good protection capacity, whereas a copper surface pretreated with H3PO4 solution can substantially enhance the corrosion resistance of 1-dodecanethiol SAMs.

Pollution caused by copper is one of the key factors of environment contamination. As one of heavy metals, copper is hard to decompose in nature, the biological enrichment of which may lead to severe damage to health. Cu²⁺ detection, thus, possesses a bright application prospect both in environment protection and in human health. In this paper, a dual-functional fluorescence-magnetic composite nano-platform has been designed to sensitively detect, meanwhile capture and remove Cu²⁺ in the solution of water and ethanol (1:1, v/v). The core-shell structure nanoparticle synthesized by using Fe₃O₄ as core and SiO₂ as shell, is covalently bonded with rhodamine derivatives on the silica layer to construct the nano-platform. The emission is increased upon the addition of Cu²⁺, showing fluorescence turn on effect for the detection, and the limit of detection which was as low as 1.68 nM. Meanwhile, Cu²⁺ ions are captured by the coordination with rhodamine derivatives, and can be removable with the help of magnetic field.

A simple, efficient and stand-alone method for purification of river water using moringa seed powder and copper is discussed. Coagulant property of the seed powder clears turbid raw water and the oligodynamic activity of copper completely destroys E.coli bacteria. Both raw and treated water samples were tested for contaminants to verify the efficacy of the system. Treated water has turbidity in the range 3 NTU - 5 NTU and non-detected (< 1 MPN/100 mL) E.coli count making it suitable for drinking. The technique is very cost effective and can be practiced anywhere using locally available materials. It does not require a power source or any technical assistance. Being a stand-alone system the technique exceptionally useful in providing drinking water as an immediate solution in disaster areas affected by cyclone or floods.