Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 ml min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of colored beers, soft drinks and candies.

Novel far-red-sensitive symmetric squaraine (SQ) dyes with terminal alkyl-chain modifications were designed, synthesized and characterized aiming towards imparting multifunctionalities such as photosensitization, dye aggregation prevention and source of electrolyte components. The dye sensitizers SQ-77 and SQ-80 with the alkyl chain terminal modifications consisting of iodine and 1-methylimidazolium iodide, respectively, were designed and synthesized as new dye sensitizers for DSSCs based on the symmetric SQ-5 without any terminal modification used as reference. Upon adsorption on the mesoporous TiO2 surface, The SQ-77 depicted an enhanced dye loading and dye aggregation. On the other hand, SQ-80 demonstrated reduced dye aggregation and stronger binding on the TiO2 surface leading to enhanced durability of DSSCs. Apart from the most common photosensitization behaviour, the newly designed dye demonstrated multifunctionality such as aggregation prevention and electrolyte functionality utilizing iodine-based redox electrolyte in the presence and absence of I2 and LiI additives. In the absence of LiI and I2, a mixture of SQ-77 and SQ-80 demonstrated a photoconversion efficiency of 1.54 % under simulated solar irradiation, which was about 6 times higher as compared to reference dye SQ-5 (0.24 %) having no alkyl chai terminal modification.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

olten salt reactors (MSRs) utilize salts as coolant or as the fuel and coolant together with fissile isotopes dissolved in the salt. It is necessary to therefore understand the behavior of the salts to effectively design, operate, and regulate such reactors, and thus there is a need for thermodynamic models for the salt systems. Molten salts, however, are difficult to represent as they exhibit short range order that is dependent on both composition and temperature. A widely useful approach is the modified quasichemical model in the quadruplet approximation that provides for consideration of first and second nearest neighbor coordination and interactions. Its use in the CALPHAD ap-proach to system modeling requires fitting parameters using standard thermodynamic data such as phase equilibria, heat capacity, and others. Shortcoming of the model is its inability to directly vary coordination numbers with composition or temperature. Another issue is the difficulty in fitting model parameters using regression methods without already having very good initial values. The proposed paper will discuss these issues and note some practical methods for the effective genera-tion of useful models.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

Dyes, as indigo carmine have become indispensable to modern life being widely used in food, textile, pharmaceutical, medicine and cosmetic industries. Although indigo carmine is considered toxic and presents many adverse effects, it is heavily used in the food industry because the blue pigment is difficult to obtain from natural sources and is one of the most used dyes in the textile industry, especially for dyeing denim. Also, indigo carmine is one of the dyes used in medicine as diagnostic agent because it has impressive applicability in terms of diagnostic methods and surgical procedures. In the literature it is reported that indigo carmine is toxic for humans and can cause various pathologies, such as hypertension, hypotension, skin irritations, corneal and conjunctival disorders or gastrointestinal disorders. In this review, we discuss the structure and properties of indigo carmine, its use in various industries and medicine, the adverse effects of its ingestion, injection or skin contact, the effects on environmental pollution and its toxicity testing.

After a survey on polymer plasticization theories and conventional criteria to evaluate polymer-plasticizer compatibility through the solubility parameter, an attempt to create a polymer-plasticizers polarity scale through solvatochromic dyes has been made. Since the Reichardt’s ET(30) dye is insoluble in rubber hydrocarbon polymers like polyisoprene, polybutadiene and styrene-butadiene copolymers and is not also useful for the evaluation of the hydrocarbons and ester plasticizers, the Nile Red solvatochromic dye was instead used extensively and successfully for this class of compounds. A total of 53 different compounds were evaluated with the Nile Red dye and wherever possible also with the ET(33) Reichardt’s dye. A very good correlation was then found between the Nile Red scale E(NR) and the Reichardt’s ET(30) scale for this class of compounds focusing on diene rubbers and their typical hydrocarbons and new esters plasticizers. Furthermore, the E(NR) scale shows also a reasonable correlation with the total solubility parameter calculated according to the Van Krevelen method. Based on the above results, some conclusion was made about the compatibility between the diene rubbers and the conventional plasticizers as well as some new and green plasticizer proposed for the rubber compounds.

In this work, a high throughput nanozymatic method was developed for green nanozyme-mediated biodegradation of organic dyes in real water media. The nanozymes were synthesized and characterized for their size and morphology by TEM and DLS analysis. The nanozymatic properties of the as-prepared nanomaterials were evaluated by standard enzyme activity assay, revealing high peroxidase-like performances for the as-prepared nanozymes. Therefore, for exploring more precise, the kinetics behavior of the as-prepared nanozymes was evaluated by the standard Lineweaver-Burk method, revealing a V_max as high as 0.263 µM sec^-1 and a K_m as low as 0.03 mM, revealing high catalytic efficiency and affinity of the as-prepared nanozymes. Hence, the as-prepared nanozymes were utilized for organic dye degradation in real water media using methylene blue as a model organic dye. The effective factors on the dye degradation including pH, ionic strength, degradation time, nanozyme amount, etc. were optimized by the one-factor-at-a-time optimization method. At optimal experimental conditions, the as-prepared nanozymes can degrade about 99.0% of the organic dye within a degradation time as low as 7 min. The developed method was finally employed for the nanozyme-mediated degradation of methylene blue from real water media such as pool, mineral, river, and tap water samples. The results of this study revealed an excellent biodegradation yield of over 94.3%-99.0% for the different real samples, proving the suitability of the developed method for dye degradation in real water media.

The role of hydrogen in a future energy system with a high share of variable renewable energy sources (VRES) is regarded as crucial in order to balance fluctuations in electricity generation. These fluctuations can be compensated for by flexibility measures such as the expansion of transmission, flexible generation, larger back-up capacity and storage. Salt cavern storage is the most promising technology due to its large storage capacity, followed by pumped hydro storage. For the underground storage of chemical energy carriers such as hydrogen, salt caverns offer the most promising option owing to their low investment cost, high sealing potential and low cushion gas requirement. This paper provides a suitability assessment of European subsurface salt structures in terms of size, land eligibility and storage capacity. Two distinct cavern volumes of 500,000 m³ and 750,000 m³ are considered, with preference being given for salt caverns over bedded salt deposits and salt domes. The storage capacities of individual caverns are estimated on the basis of thermodynamic considerations based on site-specific data. The results are analyzed using three different scenarios: onshore and offshore salt caverns, only onshore salt caverns and only onshore caverns within 50 km of the shore. The overall technical storage potential across Europe is estimated at 84.8 PWh_H2, 27% of which constitutes only onshore locations. Furthermore, this capacity decreases to 7.3 PWh_H2 with a limitation of 50 km distance from shore. In all cases, Germany has the highest technical storage potential, with a value of 9.4 PWh_H2, located onshore only in salt domes in the north of the country. Moreover, Norway has 7.5 PWh_H2 of storage potential for offshore caverns, which are all located in the subsurface of the North Sea Basin.

The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

In the East, it has already become a tradition to prepare dry powdered seasonings from the fruits of the sumac plant (Rhus coriaria L.). In this work, we tested their processing by extraction. Sumac was collected in mid-September in a mountain forest near the village of Gezik (Guba, Azerbaijan). Before extraction, it was first dehydrated in a drying cabinet SH-DO-149 FG (Southern Bark) to an air-dry state; then crushed in a Tube Mill control mill (Germany) into pieces of 1-3 mm in size. One- and two-stage maceration extraction was tested together with water or acidified water at temperatures from 20 to 80 °C. Evaporation of primary extracts was carried out in a rotary evaporator Lab Rot 2 L (China). The concentration of coloring substances in the extract (in units of optical density) was used as an output parameter. It was found that the use of two-stage extraction and acidified water with a concentration of citric acid 0.3 g/cm³ contributes to the extraction of the maximum amount of coloring substances and increases the transparency of the resulting extracts, which allows the extracted extracts to be concentrated directly to obtain a new type of natural food dye. The involvement of sumac fruits in industrial processing will increase the need for these medicinal fruits, and this, in turn, will serve as an incentive for the introduction of this medicinal plant into culture.

The present study analyzed the efficiency of a naturally derived fenugreek powder for removal of Congo red dye from the aqueous solution. The flocculation Studies on Congo Red (CR) a hazardous, textile dye onto Fenugreek Powder and its adsorption was analyzed. Fenugreek Powder is Eco-friendly, biodegradable and locally available in the market. The dye adsorption process was performed in different batches at varying pH, dye concentration, adsorbent concentration and contact time to get the best results. The result showed that the maximum removal of dye was 42.4% with 10mg/l of Fenugreek powder at pH 4.

Elevated salinity is one of the major environmental limitation factors of plant growth and development and salinity stress compromises the production and survival of plantation and urban forests and agricultural crops in the arid, semi-arid, and intertidal zones. Ulmus pumila, a salt- indigenous tree species in Asia and is widely deployed in salt-affected areas in China, and U.pumila is promising for multi-varietal forestry in plantation and urban forests. The comprehensive mechanism of the intraspecific salt tolerance is still not clear yet. Here, we investigated the physiological responses of the salinity stress based on the antioxidant enzyme activities, osmotic adjustments, and gas exchange among salt-tolerant U. pumila genotypes for 100 days under five different NaCl levels (0%, 0.3%, 0.5%, 0.7%, and 0.9% w/v) with natural surroundings and rain shade at age-2. Salt stress decreased height (HR), ground diameter (DR), and dry weight (biomass) were significantly different among genotypes. HR and performance indices were positively correlated with photosynthesis rate (Pn), apparent mesophyll conductance (AMC), and chlorophyll (CHLL) with (r= 0.7 - 0.8 ***), but were negatively related to the free proline, sugar, and protein accumulation (r=-0.5 ~ -0.7***). We found that high accumulation of sugars and more activities of SOD enzyme in leaf tissue contribute to the osmotic adjustment and ROS scavenging system under salinity treatment; the sugar content and SOD activity play key roles in U. pumila’s tolerance to salt stress, and are promising indicators for U. pumila species ex vitro selections. The ex vitro selection results align with the previous in vitro studies [37] and is promising for the MVF development.

Disposing pollutants into water sources has posed risks to human health and the environment, and biosorption has emerged as an eco-friendly, cost-effective, and green alternative for wastewater treatment. This work shows banana peel powder (BPP) biosorbents for efficient sorption of methylene blue (MB), atrazine, and glyphosate pollutants. The biosorbent highlights several surface chemical functional groups and morphology containing agglomerated microsized particles and microporous structures. BPP showed 66% elimination of MB in 60 min, with an adsorption capacity (qe) of ~33 mg g-1, where a combination of film diffusion and chemisorption governed the sorption process. Besides, the biosorbent removed 91% and 97% of atrazine and glyphosate pesticides after 120 min, with qe of 3.26 and 3.02 mg g-1, respectively. The glyphosate and atrazine uptake best followed the Elovich and pseudo-first-order kinetic, respectively, revealing different sorption mechanisms. Our results suggest that BPP are low-cost biomaterials for green and environmentally friendly wastewater treatment.

Development of biomarkers of analytes with interest in clinic is an important field of study. In this work, we synthesized and analyzed the new fluorescent acetate-biomarker, Iso-PG. The mechanism of detection is the acetate buffer mediated proton transfer reaction. The rate constants involved were obtained, and we measured the change in the fluorescence lifetime produced as a consequence of the presence of acetate in the medium. Finally, we checked its potential use as acetate biomarker in synthetic serum

Salt stress is one of the most severe environmental stresses limiting the productivity of crops, including rice. However, there is a lack of information on how salt-stress sensitivity varies across different developmental stages in rice. In view of this, a comparative evaluation of contrasting rice varieties CSR36 (salt tolerant) and Jaya (salt sensitive) was conducted, wherein NaCl stress (50 mM) was independently given either at seedling (S-stage), tillering (T-stage), flowering (F-stage), seed-setting (SS-stage) or throughout the plant growth, from seedling till maturity. Except for S-stage, CSR36 exhibited improved NaCl stress tolerance than Jaya, at all other tested stages. Principal component analysis (PCA) revealed that the improved NaCl stress tolerance in CSR36 coincided with enhanced activities/levels of enzymatic/non-enzymatic antioxidants (root ascorbate peroxidase for T- and S+T stages and root catalase for F-, S+T and S+T+F-stages) and higher accumulation of osmolytes (shoot proline for F-stage and S+T+F-stage), indicating better antioxidant capacitance and osmotic adjustment, respectively. In contrast, higher shoot accumulation of Na+ and consequent increase in Na+/K+, Na+/Ca+2 and Na+/Mg+2 ratio in root and shoot, were identified as major variables associated with NaCl stress induced growth reduction in Jaya. In addition, CSR36 exhibited higher levels of Fe3+, Mn2+ and Co3+ and lower Cl- and SO42-, suggesting its potential to discriminate essential and non-essential nutrients, which might contribute to NaCl stress tolerance. Taken together, the findings provided the frame-work for stage-specific salinity responses in rice, which will facilitate crop-improvement programs for specific ecological niches including the coastal regions. Rice, salt stress, stage-specific salinity, antioxidant defense, ionic homeostasis, salt tolerance

In this work, we report the engineering of a sub-70 nm nanocomposite of ZnO/Zn2TiO4 using a low-temperature solution-phase method. Titanium isopropoxide and zinc acetate were used as precursors, and isopropyl alcohol and water were used as solvents. The investigation focused on the growth of nanocomposites by varying the concentrations of precursors and surfactants, as well as their efficiency within different pH ranges. All three ZnO/Zn2TiO4 nanocomposites consist of hexagonal wurtzite ZnO and Zn2TiO4 structures in the three nanocomposites. The crystallite size in three ZnO/Zn2TiO4 nanocomposites, with a hexagonal wurtzite ZnO structure, were measured to be 62.67, 40.34, and 39.50 nm. The crystallite size values in three ZnO/Zn2TiO4 nanocomposites were 26.15 nm, 25.36 nm, and 21.24 nm, respectively, with Zn2TiO4. Morphological observations, conducted using FESEM, reveal the formation of three ZnO/Zn2TiO4 nanocomposites across the entire sample. These nanocomposites resemble dispersed cotton packets, with sizes ranging from 18 to 350 nm. Peaks in the range of 610-1250cm-1 are attributed to Ti-O bond formation and peak located at 1350-1450 cm-1 are attributed to Zn-O bond formation. Also, EDX spectrum reveals peaks for various sample components such as Ti, O and Zn. UV spectrums confirmed the formation of three nanocomposite of ZnO/Zn2TiO4 as showing two peaks for each sample. Photocatalytic investigation carried out by analyzing the UV-Visible absorption spectra of methylene blue dye on the surface of ZnO/Zn2TiO4 nanocomposites, dye degradation at various irradiation time intervals, dye degradation at varied catalyst concentrations and the influence of pH on dye-degradation. Furthermore, the said nanocomposites were used to degrade environmental pollutant (Methylene blue dye). Different sets of experiments were conducted under ambient conditions which show an excellent photo catalytic degradation efficiency.

Water pollution is regarded as a dangerous problem that needs to be resolved right away. This is largely due to the positive correlation between the increase in global population and waste production, especially food waste. Hydrogel beads based on sodium alginate (Alg) and pomegranate fruit peels (PP) were developed for the adsorption of Safranin O dye (SO) in aqueous solutions. The obtained Alg-PP beads were widely characterized. The effects of the contact time (0-180 min) and initial concentration (10-300 mg/l), the initial pH (2-10), the adsorbent dosage (1-40 g/l) and the temperature (293-333 K) were investigated through batch tests. The data proved that the adsorption kinetics of SO reached equilibrium within 30 min and up to 180 min. The adsorption data of SO onto synthesized beads follow the pseudo second-order model. The experimental data fitted very well to both Freundlich and Langmuir models. The maximum adsorption capacity of Alg-PP could reach 8.99 mg/g at 293 K. Calculation of Gibbs free energy and enthalpy indicated that adsorption of SO onto Alg-PP is spontaneous and endothermic. Finally, analysis of diffusion and mass transport phenomena were presented. The reported results revealed that the Alg-PP beads could be used as a novel natural adsorbent for the removal of cationic dye pollutants from aqueous environments.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

A lignin modified salt resistance branched high-performance water reducer was prepared via free radical polymerization. The water reducing agent was identified through Fourier transform infrared analysis, thermal gravimetric analysis, and scanning electron microscopy. The experiment conducted on cement paste demonstrates that the water-reducing efficiency can reach a maximum of 44%. Additionally, the significant spatial steric hindrance of the application enhances the dispersal capability of the water-reducing agent, resulting in effective water reduction and reduced viscosity. In addition, its compressive strength is the highest after 3-day curing and 3, 7, 28-day standard curing, and it has the best overall performance both in water and saline water prepared systems.The application in oil cement slurry shows that it exhibits good dispersibility in fresh water, saline water, and substitute ocean water. In the Halfaya and Missan Oilfields of Iraq, BHPWR was used in slurry with a density of 2.28g cm-3 for casing the 244.5 mm salt paste layer of five wells. Cementing results exceeded expectations with over 85% excellent and 100% qualified.

Keywords: Knowledge; Attitudes; Practices; Salt intake.

Rock salt is characterized by specific geomechanical and rheological properties. Layers of rock salt on depth over 900 m cause problems with shaft lining deformation. Methods of shaft lining protection used so far (e.g. in Sieroszowice mine) have not been effective enough. The research presents a patented and copyright protected concept of a shaft lining construction that can be used in rock masses with strong rheological properties and susceptible to leaching. In the case of salt layers, especially at significant depths the relative convergence of the heading contour may be about 40 ‰/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, is not sufficient to ensure the stability of the shaft guidance geometry. In the new shaft lining concept, the excessive rock creep into the outbreak inside the shaft diameter is removed by local and controlled leaching of the shaft cheeks by means of fresh water through a porous medium at the contact layer behind the watertight tubing lining. The article presents the methodology of performing tests on a special device and the test results.

Nuclear fission technologies have the potential to play a significant role in the energy mix of a net-zero and sustainable society. However, to achieve the sustainability goal two significant challenges remain: efficient and sustainable fuel usage and the minimisation of long term nuclear waste. Civil nuclear molten salt systems and technologies offer the opportunity to address both, delivering future reactors at scale for efficient and effective power production and nuclear waste burnup. Potentially, both objectives could be fulfilled in one reactor system, which could significantly improve sustainability indices. In addition, demand driven development of a significantly reduced fuel cycle with enhanced proliferation resistance offers further potential for improvement. To achieve these goals, a transformative approach for salt clean-up during molten salt reactor operation is proposed in this work, by concentrating on the detection and removal of key neutron poisoning elements which prevent the reactor from long-term operation. This work also demonstrates the importance of the effective integration of physics, reactor design and chemistry when systems modelling in achieving these system development goals.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

It is shown that structuring at the microlevel is the intrinsic property of water and aqueous solutions. At room conditions water (including "ultrapure" one) and aqueous solutions are dispersed systems in which microcrystals of NaCl, surrounded by a layer of hydrated water (average diameter - 10-15 microns), are "elementary microparticles", which form the basis of the dispersed phase. Possible ways of formation of these microparticles and their evolution in the process of evaporation of unstructured part of water - dispersion medium - are considered. It is shown, in particular, that they are present in the air as aerosol contaminants. When the ionic strength of the solution increases, the water-salt particles coagulate, forming a new phase - coacervates, remaining on the substrate after evaporation of the liquid part of the water. The aggregates of coacervate structures, formed in a liquid medium, are disordered during heating, which can cause a change in a number of physicochemical properties of water at the temperatures of 50°-60°C range that have not been correctly explained in the framework of atomic-molecular concepts.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

Water pollution, driven largely by the discharge of organic dyes from various industrial processes, presents a grave environmental threat. This study delves into the promise of an innovative adsorptive composite material composed of chitosan and activated charcoal, offering a sustainable and efficient solution for removing methylene blue (MB) dye from water sources. Our comprehensive investigation encompasses the synthesis, characterization, and adsorption capabilities of this composite material, revealing its remarkable physicochemical attributes and its substantial capacity to adsorb MB dye. These findings establish it as a compelling candidate for water treatment applications. The assessment of adsorbent dosage shows a direct correlation between higher dosages and enhanced MB dye removal, with an optimal dosage determined at 0.4 g/25 mL. Furthermore, pH-dependent studies demonstrate exceptional performance at lower pH levels, achieving an impressive 95% removal rate at pH 3 after 240 minutes of contact time. The composite exhibits consistent high removal percentages across a wide range of MB dye concentrations, showcasing its adaptability. In terms of reaction time, the composite achieves peak adsorption capacity within the initial 360 minutes and maintains a stable equilibrium, sustaining an impressive 99% removal efficiency thereafter. This study underscores the eco-friendliness and cost-effectiveness of the composite material, emphasizing its potential to address water pollution challenges and promote sustainable water resource management. Overall, this research yields valuable insights into a practical approach for mitigating the adverse impact of organic dyes on aquatic ecosystems and public health.

The presence of dyes in wastewater effluents made from the textile industry is a major environmental problem due to their complex structure and poor biodegradability. In this study, a cationic lignin polymer was synthesized via the free radical polymerization of lignin with [2- (methacryloyloxy) ethyl] trimethylammonium chloride (METAC) and used to remove anionic azo-dyes (reactive black 5, RB5, and reactive orange 16, RO16) from simulated wastewater. The effects of pH, salt and concentration of dyes, well as the charge density and molecular weight of lignin-METAC polymer on dye removal were examined. Results demonstrated that lignin-METAC was an effective flocculant for the removal of dye via charge neutralization and bridging mechanisms. The dye removal efficiency of lignin-METAC polymer was independent of pH. The dosage of the lignin polymer required for reaching the maximum removal had a linear relationship with the dye concentration. The presence of inorganic salts including NaCl, NaNO3 and Na2SO4 had marginal effect on the dye removal. Under the optimized conditions, greater than 98 % of RB5 and 94 % of RO16 were removed at lignin-METAC concentrations of 120 mg/L and 105 mg/L in the dye solutions, respectively.

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

A reduction in population sodium (as salt) consumption is one of the most cost-effective strategies to reduce the burden of cardiovascular disease and it is a global health priority. High potassium intake is also recommended to reduce cardiovascular disease. To establish effective policies for setting targets and monitoring effectiveness within each country, the current level of consumption should be known. Greece lacks data on actual sodium and potassium intakes. The aim of the present study was therefore to assess dietary salt (using sodium as biomarker) and potassium intakes in a sample of healthy adults in northern Greece and to determine whether adherence to a Mediterranean diet is related to different sodium intakes or sodium-to-potassium ratio. A cross-sectional survey was carried out in Thessaloniki greater metropolitan area (northern Greece) (n=252, aged 18-75 years, 45.2% males). Participants’ dietary sodium and potassium intakes were determined by 24h urinary sodium and potassium excretions. In addition, we estimated their adherence to Mediterranean diet by the use of an 11-item MedDietScore (range 0-55). The mean sodium excretion was 175 (SD 72) mmol/day, equivalent to 4,220 (1,745) mg of sodium or 10.7 (4.4) g of salt per day and potassium excretion was 65 (25) mmol/day, equivalent to 3,303 (1,247) mg/day. Men had higher sodium and potassium excretions compared to women. Only 5.6% of the sample had salt intake <5g/d, which is the target intake recommended by the WHO. Mean sodium-to-potassium excretion ratio was 2.82 (1.07). There was no significant difference in salt or potassium intake or their ratio across MedDietScore quartiles. No significant relationships were found between salt intake and adherence to Mediterranean diet, suggesting that the perception of the health benefits of the Mediterranean diet does not hold when referring to salt consumption. These results suggest the need for a larger nation-wide survey on salt intake in Greece and underline the importance of continuation of salt reduction initiatives in Greece.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

A magnetite (CDC@Fe3O4) heterogeneous photocatalyst was synthesized via treated and modified cotton in two steps. The designed nanocomposites were characterized by FTIR, TGA, XRD, SEM, and VSM analyses. The Fenton-photocatalytic decomposition efficiency of the synthesized magnetic catalyst was evaluated under visible sunlight using Methyl Orange (MO) as a model organic pollutant. The impacts of several degradation parameters, including the light source, catalyst load, irradiation temperature, oxidant dose, and pH of the dye aqueous solution and its corresponding concentration on the Fenton photodegradation performance, were methodically investigated. (CDC@Fe3O4) heterogeneous catalyst showed a remarkable MO removal rate of 97.9% at 10 min under visible-light irradiation. (CDC@Fe3O4) nanomaterials were also used in a heterogeneous catalytic optimized protocol for a multicomponent reaction procedure to obtain nine tetra-substituted imidazole derivatives. The green protocol afforded imidazole derivatives in 30 min with good yields (91-97%) at room temperature and under ultrasound irradiation. Generally, a synthesized recyclable heterogeneous nano-catalyst is a good example and is suitable for wastewater treatment and organic synthesis.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

This study demonstrates the viability of an orange peel-based adsorbent as sustainable alternative for the elimination of the disperse dye C.I. Disperse Blue 56 present in waste waters of the dyeing industry of textiles. The effectiveness of the adsorbent is evaluated at different pH values and the adsorption capacity is determined by systematically comparing orange peel and the final adsorbent chemically treated. Results reveal an spontaneous coagulation-flocculation phenomenon of the dispersed dye at low pH values which represents a sustainable way for the recovery and possible re-use of the dye, together with the industrial valorisation of a wasting product as is orange peel.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

Two ligands, 1, 3-bis(4-carboxyphenyl)imidazolium chloride and 4, 4՛-bipyridine, were employed to prepare nickel and zinc azolium based MOFs, 1 and 2 by the mixed ligand solvothermal approach. The positively charged azolium moieties in the imidazolium linker resulted in a charged environment in the as-synthesized frameworks. As a result, 1 and 2 demonstrated preferential adsorption of CO2 over methane molecules in the gas phase adsorption due to the higher quadruple moment of CO2, which interacts more with the positively charged frameworks. Besides, in aqueous media, 1 and 2 exhibited incredible adsorption efficiency for anionic dyes. In the following, MOF 1 was metallated at the carbene site of the azolium linker to generate the novel heterogeneous catalyst 1-Pd, which was successfully applied for Sonogashira and Suzuki-Miyaura coupling reactions without losing its activity after three cycles.

Although laccase has been recognized as a wonder molecule, and green enzyme, the use of low yielding fungal strains, poor production, purification, and low enzyme kinetics have hampered its larger-scale applications. Hence the present research was aimed to select high yielding fungal strains and to optimize the production, purification, and kinetics of laccase of Aspergillus sp. HB_RZ4. Aspergillus sp. HB_RZ4 produced a copious amount of laccase on under meso-acidophillic shaking conditions in a medium containing glucose and yeast extract. A 25 µM of CuSO4 enhanced the enzyme yield. The enzyme was best purified on Sephadex G-100 column. Purified enzyme resembled with the laccase of A. flavus. Kinetics of purified enzyme revealed the high substrate specificity and good velocity of reaction with ABTS as substrate. The enzyme was stable over a wide range of pH and temperature. The peptide structure of the purified enzyme resembled with the laccase of A. kawachii IFO 4308. The fungus decolorized various dyes independent of the requirement of a laccase mediator system (LMS). Aspergillus sp. HB_RZ4 came out as a potent natural producer of laccase, it decolorized the dyes even in absence of LMS and thus can be used for bioremediation.

Chloroquine was among the first of several effective drug treatments against malaria until the onset of chloroquine resistance. In light of diminished clinical efficacy of chloroquine as an antimalarial therapeutic, there is potential in efforts to adapt chloroquine for other clinical applications, such as in combination therapies and in diagnostics. In this context, we designed and synthesized a novel asymmetrical squaraine dye coupled with chloroquine (SQR1-CQ). In this study, SQR1-CQ was used to label live Plasmodium falciparum (P. falciparum) parasite cultures of varying sensitivities towards chloroquine. SQR1-CQ positively stained ring, mature trophozoite and schizont stages of both chloroquine–sensitive and chloroquine–resistant P. falciparum strains. In addition, SQR1-CQ exhibited significantly higher fluorescence, when compared to a chloroquine-BODIPY (borondipyrromethene) conjugate. We also achieved successful SQR1-CQ labelling of P. falciparum directly on thin blood smear preparations. Drug efficacy experiments measuring half-maximal inhibitory concentration (IC50) showed lower concentration of effective inhibition against resistant strain K1 by SQR1-CQ compared to conventional chloroquine. Taken together, the versatile and highly fluorescent labelling capability of SQR1-CQ and promising preliminary IC50 findings potentiates it to be further developed as a promising diagnostic bioimaging tool with drug efficacy against chloroquine-resistant P. falciparum.

During their growth, bacteria respond to complex environmental changes through equally com-plex and orderly regulatory mechanisms. sRNA has an important role as a post-transcriptional regulator in the environmental adaptation of Bacillus. In this study, we identified an sRNA Bvs091 located in the intergenic region of the Bacillus velezensis, which is widely present in the genus Bacillus and whose expression is upregulated by salt treatment. The deletion of bvs091 in B. ve-lezensis PEBA20 led to a reduced growth rate and a change in the phenotypes, with simple colony structures and low and easily degradable biofilm. Salt tolerance tests indicated that the deletion of bvs091 results in a reduced salt tolerance. galT2 mRNA is supposed to be a direct target of Bvs091 according to results obtained by using the bioinformatic method and performing qRT-PCR analysis. The microscale thermophoresis (MST) analysis showed that Bvs091 could directly bind 28‒51 bases in front of the promoter of galT2. Subsequently, the deletion of galT2 in B. velezensis resulted in increased salt tolerance. Based on the techniques of double plasmids and a half-life period, sRNA Bvs091 is confirmed as a trans-encoded sRNA that negatively regulates the mRNA expression of galT2. In brief, the trans-encoded sRNA Bvs091 acts by pairing the incomplete complementary bases of galT2 mRNA, reducing galT2 mRNA’s stability and affecting the trans-lation efficiency.

Rice (Oryza sativa L.) is a primary energy food for Asian population. One of the most constraints in rice production is soil salinity because of the rice is very susceptible to salt. Meanwhile, many agricultural land in Asia are in the saline area. It is important to identify and develop salt-tolerant rice varieties that can adapt in Asian climate. By combining morphological, physiological, and biochemical assessments for screening the salt tolerant of 116 Asian rice cultivars was able to classify into tolerant, moderate, and sensitive rice cultivars under salinity stress condition, and also for understanding the salt tolerance mechanisms. The rice cultivars which belong to salt-tolerant including Pokkali from India, TCCP 266 from Philippines, IR 45427 also from Philippines, and Namyang 7 from Korea. Whereas, salt-sensitive rice varieties like IR29 from Philippines, IR58 also from Philippines, Daegudo from Korea, and Guweoldo also from Korea. The salt-tolerant varieties showed signs of tolerance, including lower percent reduction of percentage germination, root length, root fresh weight, shoot length, plant biomass, and chlorophyll content. In order to maintain the cellular osmotic balance under saline condition, the salt-tolerant ones exhibited less membrane damage, lower Na/K ratio, high proline and sugar accumulation, lower malondialdehyde (MDA) and hydrogen peroxide (H2O2). Pokkali from India, TCCP 266 from Philippines, IR 45427 also from Philippines, and Namyang 7 from Korea are recommended as valuable germplasm resource for Asian rice breeding program in saline agricultural area.

Deep eutectic solvents (DESs) are known as tunable solvents. It is possible to prepare ternary deep eutectic solvent (TDES) are used for desired purpose by selecting the suitable molar ratio and components of mixture. Therefore, four DESs and two TDESs were prepared in this work. DESs and TDESs were prepared with potassium carbonate (PC) as a hydrogen bond acceptor (HBA) and three hydrogen bond donors (HBDs) such as glycerol (GL), ethylene glycol (EG) and 2-amino-2methyl-1-3-propanediol (AMPD) known as a hindered amine (HA). Binary DESs were PC-GL with molar ratios 1:10 and 1:16 and PC-EG with the same molar ratios. TDES were prepared by adding AMPD in binary DESs such as PC-GL-AMPD 1:16:1 and PC-EG-AMPD 1:10:1. The experimental density and refractive index of all DESs and TDESs were measured at the temperature of 293.15 to 343.15 K with an interval of 5 K. The effect of temperature, molar ratio and alkyl chain length on the properties was investigated. The molar volumes and isobaric thermal expansion were calculated using experimental density data. The experimental refractive index data was used to derive the specific refraction, molar refraction, free molar volume, electronic polarization, polarizability constant and internal pressure at several temperatures.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

A novel synthetic strategy is disclosed to prepare a new class of metalorganic copolymers which contain iron(II) clathrochelate building blocks by employing a mild and cost-effective copper-catalyzed [4 + 2] cyclobenzannulation reaction, using three specially designed diethynyl iron(II) clathrochelate synthons. The target copolymers CBP1-3 were isolated in high purity and excellent yields as proven by their structural and photophysical characterization, namely, Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption and emission spectroscopies. Thermogravimetric analysis (TGA) of CBP1-3 reveals excellent chemical stability. Investigation of the adsorption properties of the target copolymers towards the carcinogenic methyl red dye from aqueous solution reveals a quantitative uptake in 30 minutes. Isothermal adsorption studies disclose that methyl red uptake from aqueous solution follows Langmuir model for all the target copolymers reaching a maximum adsorption capacity (qm) of 431 mg g‒1, whereas kinetic investigation reveals that the adsorption follows pseudo first-order with an equilibrium adsorption capacity (qe,cal) of 79.35 mg g‒1 and whose sorption property was sustained even after its reuse several times.

The use of intelligent sensor-based packaging in food products provide quick evaluation of the quaility of the food. This study was done to develop bio-based color sensor from surimi-based color sensor incorporated with sappan wood extract (SWE) for smart food packaging. The SWE with different concentration (0.15%, 0.25%, and 0.35%) was incorporated to the myofibrillar protein-based edible film. The sappan wood-surimi edible film (SSEF) was subjected to physical properties analysis and the color changes at different pH values and soaking time at different condition were evaluated. Based on the results, different concentration of the SWE significantly (p&lt;0.05) affected the physical properties of the film. With the increasing of pH values, the darkness, redness, and blueness of the film was increased. Based on the evaluation of the SSEF with different soaking condition, the color changes of the film in acidic condition were more stable than in neutral and alkaline condition. The results from this study showed that SSEF have the possibilities to be used as a smart food packaging possessing the capabilities to act as color sensor due to its sensitivity to the changes in pH condition of the product.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes, free of polluting substance has assumed a preponderant role. The aim of this work is propose a bioinspired, facile, at low cost, non-toxic and environmentally friendly alternative to obtaining magnetic nanoparticles whit a majority phase of magnetite (Fe₃O₄). Is important to empathize that the synthesis was based on the chemical reduction through the Cnicus Benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus Benedictus is abundant endemic plant in Mexico, with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe₃O₄ nanoparticles (Fe₃O₄ NP’s) was calculated by Williamson-Hall method. The photocatalytic properties of the Fe₃O₄ NP´s were studied by kinetics absorptions models in the Congo red (CR) degradation. Finally the antibacterial effect of the Fe3O4 NP´s were evaluated mediated the Kirby-Bauer method against E. coli and S. aureus bacteria. This route offers a green alternative to obtain Fe3O4 NP´s with remarkable magnetic, photocatalytic and antibacterial properties.

In this work was investigated the potential of Bacillus subtilis UCP 0146 in the bioconversion of the medium containing 100% of cassava flour wastewater to obtain bioemulsifier. The evaluation of the production was carried out by the emulsification index (IE24) and surface tension (TS). The ionic charge, stability (temperature, salinity and pH measured by IE24 and viscosity), ability to remove and disperse oil and textile dye were investigated. B.subtilis produced an anionic bioemulsifier in the medium containing 100% of cassava wastewater in condition 4 of the factorial design (9% of the inoculum, at 35 °C and agitation of 100 rpm) with surface tension of 39mN/m, IE24 of 95.2 % and yield 2.69 g.L-1. Stability at different pH (2-8), temperatures (0-120ºC) and NaCl, dispersed (55.83 cm2-ODA) and reduced the viscosity of the burned engine oil (90.5 cP) , removed 94.4% petroleum and demonstrated efficiency in methylene blue removal (62.2%). The bioemulsifier and its synthesis from bacteria and also emphases on the role of surfactants in oil remediation.

Hierarchical micro-/mesoporous graphitic carbon spheres (HGCS) with a uniform diameter of ~0.35 μm were synthesized by Fe-catalyzed graphitization of amorphous carbon spheres resultant from hydrothermal carbonization. The HGCS resultant from 3 h at 900 °C with 1.0 wt% Fe catalyst had high graphitization degree and surface area as high as 564 m²/g. They also exhibited high specific capacitance of 140 F/g at 0.2 A/g, good electrochemical stability with 94% capacitance retention after consecutive 2500 cycles. The graphitization degree of the HGCS contributed about 60% of their specific capacitance, and their specific capacitance per unit surface area was as high as 0.2 F/m² which was much higher than in the most cases of porous amorphous carbon materials reported before. In addition, the HGCS showed a high adsorption capacity of 182.8 mg/g for methylene blue (MB), which was 12 times as high as that in the case of carbon spheres before graphitization.

Salt stress is one of the major abiotic stresses that lead to crop yield reduction worldwide. Melatonin (MT), an endogenous hormone synthesized in plants, plays an important role in responding to abiotic stimuli such as drought, salinity, heat, cold, etc. However, the molecular mechanisms of MT-mediated abiotic stresses remain to be better understood. In order to explore the key genes and pathways of melatonin in alleviating salt stress, physiological and biochemical indicators as well as transcriptomics profile were conducted in alfalfa seedlings. The results showed that the germination rate, bud length and fresh weight of alfalfa seedlings added with melatonin were higher than those treated with salt alone. In addition, Malondialdehyde (MDA) and Superoxide anion (O2-) contents also displayed a decreasing trend. The activity and content of Superoxide dismutase (SOD)、peroxidase (POD) and Glutathione (GSH) increased to varying degrees. In order to further reveal the molecular mechanism of MT-mediated salt tolerance of alfalfa, transcriptome analysis was performed on alfalfa seedlings. 2,181 differentially expressed genes (DEGs) were obtained in the salt-treated group, including 780 upregulated genes and 1,401 down-regulated genes, while 4,422 DEGs were obtained in the MT group, among which 1,438 were upregulated and 2,984 were downregulated. By using GO functional annotation and KEGG pathway enrichment, we found that DEGs were mainly enriched in the biosynthesis of flavonoids, isoflavones, plant hormones, Glutathione (GSH), soluble sugars and other substances, as well as in the ABC transporter and MAPK signaling pathways. Among them, the DEGs in the MT group was more enriched in these pathways, suggesting that MT can combat salt stress by regulating the expression of genes related to phytohormone and antioxidant capacity, which has important reference value for the breeding of salt-tolerant alfalfa and other crops.

Stresses due to drought and high soil salt content are the most severe threats to global rice pro-duction, causing a significant decline in rice yield. Therefore, this study examined the effects of treatment with various plant extracts on the stresses on rice plants associated with drought and high salinity. Additionally, this study examined various physiological and biochemical parameters such as growth, photosynthetic activity, chlorophyll content, and lipid peroxidation in rice plants after treatment with selected plant extracts under drought and salt stress conditions. Out of the eleven extracts tested, four extracts, namely soybean leaf, soybean stem, Chinese chive, and onion extracts, were found to effectively reduce drought stress. A reduction of only 24-37% in shoot fresh weight was observed in rice plants under drought stress that were treated with these ex-tracts compared to the 78% reduction observed in control plants. In addition, rice plants under salt stress which were treated with soybean leaf, soybean stem, moringa (Moringa oleifera), and Undaria pinnatifida extracts were observed to have lower reductions in shoot fresh weight (3-23%) com-pared to the control plants (43%). The effectiveness varied with the concentrations of the plant ex-tracts. Water content was higher in the rice plants treated with extracts than in the control plants after 6 days of drought and salt stress, but not after 4 days of drought and salt stress. Although photosynthetic efficiency (Fv/Fm) and electron transport rate (ETR), and the content of pigments (chlorophyll and carotenoid) varied based on the types and levels of stress and the extracts that the rice plants were treated with, generally photosynthetic efficiency and pigment contents were higher in the treated rice compared to control plants than in the control plants. Reactive oxygen species (ROS) such as the superoxide radical, hydrogen peroxide (H2O2), and malondialdehyde (MDA) levels increased as the duration of the period of stress increased. ROS and MDA levels were lower in the treated rice compared to control plants. Proline and soluble sugar accumulation also increased as the duration of the stressperiod increased. However, proline and soluble sugar ac-cumulation were lower in the treated rice compared to control plants. Generally, all the parame-ters investigated in this study were similar regardless of the plant extract used for treating the rice plants. Thus, extracts found to be effective in this study can be used to alleviate the adverse effects of stress on rice crops associated with drought and high salinity soil.

A rapid synthesis of chiral sulfoxide-functionalized meta-terphenyl derivatives by a 2,5-[C4+C2] ring transformation reaction of pyrylium salts with in-situ generated enantio-merically pure .alpha.-sulfinylacetaldehydes is described. This synthetic method demonstrates for the first time the use of .alpha.-sulfinylacetaldehydes in a reaction sequence initiated by nu-cleophilic attack of pyrylium salts by .alpha.-sulfinylcarbanions to generate chiral aromatic systems. The method presented shows broad applicability starting with various methyl sulfoxides and a number of functionalized pyrylium salts, furnishing meta-terphenyls with complex substitution patterns from readily accessible starting compounds.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

The TGACG motif-binding factor1 (TGA1) transcription factor, a significant protein in the bZIP transcription factor family, exhibits a myriad of functions, contributes to numerous biological events, and holds substantial application potential. In this study, our analysis revealed a diverse range of photoregulatory and hormone regulatory elements within the MtTGA1 promoter region. The expression profile of MtTGA1 indicated its highest expression in the root, with its regulation influenced by SA, ABA, BR, and GA. Under salt stress conditions, transgenic plants demonstrated significantly longer root lengths and heightened activities of antioxidant enzymes such as ascorbic acid catalase (APX), peroxidase (POD), catalase (CAT), and superoxide dismutase (SOD) in their roots and leaves compared to control plants. Simultaneously, the levels of endogenous hormones ABA and BR escalated in transgenic plants, with a marked change in the morphology of their leaf cells. Transcriptome analysis identified a total of 193 differentially expressed genes, implicating a wide array of biological processes. Furthermore, we found that MtTGA1 is able to interact with Medicago truncatula SPX domain containing protein 1 (SPX1). In conclusion, the MtTGA1 transcription factor plays a crucial role in enhancing salt tolerance, which provides new insights for improving plant survival under salt stress conditions.

Salinity is abiotic stress, which causes adverse environmental conditions for rice cultivation. In particular, local aromatic rice cultivation is heavily influenced by soil salinity stress, which has an impact on global food security. This study aimed to screen local aromatic rice genotypes in a hydroponics experiment using Yoshida solutions to evaluate the effect of increasing NaCl concentrations on the early growth stages of rice seedlings. Genetic diversity along with phylogenetic relationship was assessed using the random amplified polymorphic DNA (RAPD) markers. Out of 20 RAPD markers, 17 markers produced reproducible polymorphic bands. Individuals of all genotypes shared 88 (89.80%) of the 98 total RAPD elements amplified. The genetic distance-focused similarity index ranged from 0.05 to 0.94. The highest genetic distance (0.94) was discovered between genotypes Nayanmoni and Kalijira Barisal, and the lowest was between Badshabhog and Kataribhog (0.05). In addition, the OPS 3(510bp) and OPA 14(1100bp) markers could be used to identify salt-tolerant genotypes. According to genetic distance, the salt stress tolerant check genotype, Pokkali was genetically related to Chinigura as well as Kalijira Barisal. This study established a simple and consistent method for evaluating variability across various aromatic rice genotypes, which will benefit in genotype selection for breeding salinity stress tolerant aromatic rice varieties in Bangladesh.

Phytochromobilin (PΦB) participates in the regulation of plant growth and development as an important synthetase of photoreceptor phytochromes (phy). And Arabidopsis Long Hy-pocotyl 2 (HY2) appropriately works as a key PΦB synthetase. However, whether HY2 takes part in plant stress response signal network remains unknown. Here, we described the func-tion of the HY2 in NaCl signaling. The hy2 mutant was NaCl-insensitive, whereas HY2-overexpressing lines showed NaCl-hypersensitive phenotypes during seed germination. The exogenous NaCl induced the transcription and the protein level of HY2 which positively mediated the expression of downstream stress-related genes of RD29A, RD29B and DREB2A. Further quantitative proteomics showed the patterns of 7,391 proteins under salt stress. HY2 was then found to specifically regulate 215 differentially regulated proteins (DRPs) which, according to GO enrichment analysis, were mainly involved in ion homeostasis, flavonoid biosynthetic & metabolic, hormone response (SA, JA, ABA, ethylene), reactive oxygen spe-cies (ROS) metabolic, photosynthesis and detoxification pathway to respond to salt stress. More importantly, ANNAT1-ANNAT2-ANNAT3-ANNAT4 and GSTU19-GSTF10-RPL5A-RPL5B-AT2G32060, two protein interaction networks specifi-cally-regulated by HY2, jointly participated in the salt stress response. These results direct the pathway of HY2 participating in salt stress, and provide new insights for the plant to re-sist salt stress.

Art of embalming as practised by Egyptian about 3000 years ago transformed into embalming science of modern ages with the use of formaldehyde as a preservative solution. Subsequently, the search for ideal embalming preservative solution continues to date because of the health hazards related to formaldehyde preservation of cadavers. Alternative preservative methods and solutions suitable for making different skill training models with the specific requirement of pliability have also experimented. The literature had documented various solutions like Thiel’s solution and technique, phenoxyethanol preservation, saturated sodium chloride solution, cryopreservation, N-Vinyl-2-pyrrolidone, Ethanol–glycerin and Fix 4life solution as alternatives to formaldehyde preservation. This review is an attempt to have an overview comparison of all the recent alternate embalming methods applicable for developing skill training cadaveric models with an aim of reducing formaldehyde usage in preservation.

In the Republic of Moldova, nearly 90% of all deaths are due to noncommunicable diseases (NCDs), tha majority of which (58%) are caused by cardiovascular disease (CVD). Excess salt (sodium) and inadequate potassium intakes are associated with high CVD. Moreover, salt iodisation is the preferred policy to prevent iodine deficiency and associated disorders. However, there is no survey that has directly measured sodium, potassium and iodine consumption in adults in the Republic of Moldova. The aim is to estimate population sodium, potassium and iodine intakes and explore knowledge, attitudes and behaviour (KAB) towards the use of salt, amongst the adult population in the Republic of Moldova. Proportional random samples of adults were obtained from 28 of the 37 Districts and Municipalities and one Administrative Territorial Unit of Moldova. Participants attended a screening including demographic, anthropometric and physical measurements. Dietary sodium, potassium and iodine intakes were assessed by 24h urinary sodium (UNa), potassium (UK) and iodine (UI) excretions. Creatinine was measured. KAB was collected by questionnaire. Eight hundred and fifty-eight participants (326 men and 532 women, 18–69 years) were included in the analysis (response rate 66%). Mean age was 48.5 yrs (SD 13.8). Mean UNa was 172.7 (79.3) mmoL/day, equivalent to 10.8 g of salt/day and potassium excretion 72.7 (31.5) mmoL/day, equivalent to 3.26 g/day. Men ate more sodium and potassium than women. Only 11.3% of the sample had a salt intake below the World Health Organization (WHO) recommended target of 5 g/day and approximately 39% met WHO targets for potassium excretion (>90 mmoL/day). Whilst 81.7% declared limiting their consumption of processed food and over 70% declared not adding salt at the table, only 8.8% looked at sodium content of food, 31% still added salt when cooking and less than 1% took other measures to control salt consumption. Measures of awareness were significantly more common in urban compared to rural areas. Mean urinary iodine was 225 (SD: 152; median 196) mcg/24h, with no difference between sexes. According to WHO criteria, 41.0% had adequate iodine intake, 28.6% had intake below requirements and 17.8% and 12.6% had above requirement or excessive levels, respectively. Iodine content of salt table was 21.0 (SD: 18.6) mg/kg, with no difference between men and women. However, the content was lower in rural than urban areas (16.7 [SD: 18.6] vs 28.1 [SD: 16.5] mg/kg, p<0.001). There were weak or no correlations between urinary sodium and iodine excretions, and between urinary iodine excretion and iodine concentration in the table salt used in the participants’ households, indicating that in most cases participants were not using iodised salt as their main source of salt, more so in rural areas. In the Republic of Moldova, salt consumption is unequivocally high, potassium consumption is lower than recommended, both in men and in women, whilst iodine intake is still inadequate in 1 in 3 people, although severe iodine deficiency is rare. Salt consumed is often not iodised, with less iodised salt being used in rural areas.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

The study aimed to investigate the effects of colonization with two arbuscular mycorrhizal (AM) fungi, Funneliformis mosseae , Diversispora versiformis , alone and in combination on the growth and nutrient acquisition of NaCl-stressed Chrysanthemum morifolium (Hangbaiju) plants in the greenhouse experiment. Mycorrhizal and non-mycorrhizal Hangbaiju plants were grown under different salinity levels imposed by 0, 50 and 200 mM NaCl for five months, following 6 weeks of non-saline pre-treatment. The results showed that root length, shoot and root dry weight, total dry weight, shoot and root N concentration were higher in mycorrhizal than in non-mycorrhizal plants under moderate saline conditions especially with D. versiformis colonization. As salinity increased, the mycorrhizal colonization, the mycorrhizal dependence (MD) decreased. Enhancement of tissue N acquisition is probably the main mechanism underlying salt tolerance in AM plants. It is suggested that the symbiotic associations between D. versiformis fungus and C. morifolium plants may be taken as a biotechnological practice in culture.

The current performance indicator for universal salt iodization (USI) is the percent of households using adequately iodized salt. However, the proportion of dietary salt from household salt is decreasing with the increase in consumption of processed foods and condiments globally. This paper reports on case studies supported by the GAIN-UNICEF USI Partnership Project to investigate processed food industry use of adequately iodized salt in contrasting national contexts. Studies were conducted in Egypt, Indonesia, the Philippines, the Russian Federation, and Ukraine. In all cases, the potential iodine intake from iodized salt in selected food products was modelled according to the formula: Quantity of salt per unit of food product x minimum regulated iodine level of salt at production x average daily per capita consumption of the product. The percent of adult recommended nutrient intake for iodine potentially provided by the average daily intake of bread and frequently consumed foods and condiments was from 10% to 80% at the individual product level. The potential contribution to iodine intake from the use of iodized salt in the processed food industry is of growing significance. National USI strategies should encourage co-operative industry engagement and include regulatory monitoring of iodized salt use in the food industry in order to achieve optimal population iodine status.

Currently, the textile industry is among the most rapidly expanding areas of the economy and is an important source of water pollution. There are many efficient chemical and physical methods for treating textile effluent, but they produce secondary pollutants. Therefore, there is a need to manage the textile waste wastewater. The potential EPS-producing and plant growth-promoting rhizobacteria Lysinibacillus capsici PB300 (T) bacteria strain has been isolated from the bark borer-affected Peltophorum pterocarpum plant and has been determined to be effective in > 95 decolorizing Reactive Red 120, and other azo dyes such as AB11385%, orange II 94.62%, Congo red 94.62%, phenol red 94.54%, and mixtures of azo dyes 81.66%. Physico-chemical factors were optimized manually, including Taguchi design. EPS production, PGPR strain, and fabric discoloration of L. capsici were qualitatively studied. The FTIR, GC-MS, and UV absorbance studies also confirmed that the dye had been broken into its amines. Research findings using enzyme assays have shown that the bacteria Lysinibacillus capsici PB300 (T) can utilize laccase and manganese peroxidase and are capable of degrading dyes significantly. According to this work, immobilised L. capsici cells and the studied four bacterial consortiums, Lysinibacillus capsici PB300 (T), Alcaligenes faecalis subsp. Phenolicus DSM 16503 (T), Acinetobacterbaumanni ATCC 19606 (T), and Pseudomonasaeruginosa JCM 5962 may be employed to degrade RR120 effectively, and it is concluded that L. capsici PB300 (T) bacteria is significantly efficient in textile effluent treatment.

Dye-containing effluent generated in textile industries is polluting and complex wastewater. It should be managed adequately before the final destination. The up-flow anaerobic blanket (UASB) reactor application is an eco-friendly and cost-competitive treatment. The present study briefly reviews the UASB application for dye wastewater valorization. Bioenergy and clean water production potential during dye-containing wastewater treatment are emphasized to promote resource recovery in textile industries. Efficiencies of color and chemical oxygen demand of 50–97% and 60–90% are reported in bench-scale UASB studies. A biogas yield of 0.36–36.04 L d-1 in UASB, which treats dye-containing effluents, is documented. Bioenergy production and water reuse allow environmental and economic benefits. However, data on full-scale UASB treating dye wastewater are missing. Besides, studies on combined systems integrating membrane processes, such as ultrafiltration and nanofiltration, and pretreatment of wastewater and sludge for improvements in biogas production might realize the complete potential for resource recovery of UASB technology.

Oil agents produced from degreasing treatment of synthetic fibers are typical pollutants in printing and dyeing wastewater, which may cause large-scale environmental pollution without proper treatment. How to purify oily dye wastewater with low cost is a key problem at present. In this study, the biochar microspheres with oil removal ability were prepared deriving from waste bamboo chips using hydrothermal method. The structure of biochar microsphere was regulated by the activation and modification processes. The biochar microspheres were characterized and their adsorption behaviors for oily dye wastewater were explored. The results showed that the adsorption efficiency of biochar microspheres for oily dye wastewater (DTY) was improved significantly after the secondary pyrolysis and lauric acid grafting reaction. The maximum COD removal quantity of biochar microspheres for DTY was 889 mg/g with removal rate of 86.06% in 30 min. Besides, the kinetics showed that the chemisorption was the main adsorption manner. The application of biochar microspheres can decrease the costs of oily wastewater treatment and avoid environmental pollution.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Traditionally there is a gap between reactor operation and the consideration of nuclear waste in the final disposal. Fuel is produced and fuel must be disposed of in the view of the reactor operator, fuel has to be cleaned in the reprocessing and new solid fuel has to be produced in the view of the chemist. iMAGINE is designed to overcome this separation through the breakthrough development applying an optimized, integrative approach from cradle to grave of nuclear energy production as a first step to come as close as possible to the vision of zero waste nuclear power. It is described here the first time all in three the steps: reactor, fuel cycle, waste, providing the ratio behind each of the choices taken to come to the overall solution to open the discussion and thinking process on what could be achieved by a really innovative approach to integrated nuclear energy production. The opportunities regarding the handling of the remaining waste will be discussed with a view on the expectation of the final disposal community, the study ‘Nuclear waste from small modular reactors’, and the IAEA report ‘waste from innovative types of reactors and fuel cycles - a preliminary study. The aim of the is not to find answers to each of the raised points, but to identify first potential approaches and potentially promising ways to go, as well as to stimulate a discussion among experts. In the best case this could lead to a change of track for nuclear to become an even more sustainable and at least as important, trusted technology to help solve the net-zero challenge.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

This study aims to investigate a friction stir welded joint between steel and aluminum alloy. Friction stir welding is nowadays one of the most interesting joining technique due to the possibility to connect materials and thicknesses that are difficult or impossible to weld with traditional techniques. The main advantage is that Materials are not affected by thermal cycle problems during solidification and cooling and the absence of fumes and pollution during the process favors the quality of the welded joint. The life of metal joints could be greatly reduced in a corrosive environment, since the less noble material will tend to increase its corrosion rate while the nobler one will reduce its electrochemical dissolution. Accelerated ageing tests (i.e. salt fog test) are used to estimate the lifetime of metal joints in highly aggressive environments. The aim of the present work is to evaluate the durability at long ageing time in salt spray test (according to ASTM B117) of carbon steel/aluminum alloy joints, obtained by FSW. In this first part, mechanical tests results are reported. A deep metallographic and chemical investigation are going to be reported in the part 2.

Crossostephium chinense is a wild species with strong salt tolerance, which has great potential to improve the salt tolerance of cultivated chrysanthemums. Conversely, the unique salt-tolerant molecular mechanisms of Cr. chinense are still unclear. This study performed a comparative physiological and transcriptome analysis of Cr. chinense, Chrysanthemum lavandulifolium and their hybrids. The physiological results showed that Cr. chinense maintained a higher superoxide dismutase (SOD) activity, to alleviate the oxidative damage to membrane. KEGG enrichment analysis showed that the plant hormone signaling transduction and the MAPK signaling pathway were mostly enriched in Cr. chinense and hybrids under salt stress. Further weighted gene co-expression network analysis (WGCNA) of DEGs suggested that the abscisic acid (ABA) signaling transduction may play a significant role in the salt-tolerant mechanisms of Cr. chinense and hybrids. The tissue-specific expression patterns of the candidate genes related to ABA signaling transduction and MAPK signaling pathway indicated that genes related to ABA signaling transduction performed significant expression levels under salt stress. This study provides a theoretical foundation for future research into the molecular mechanism of salt tolerance in chrysanthemums under salt stress.

How to improve plant tolerance and yield under salt stress is critical for ensuring sufficient food supply since plant survival and agricultural productivity are both affected by salinity. Some evidence has showed that beneficial microorganisms have a high ability to improve plant salt tolerance and increase crop yield. But few studies were involved in effects of halotolerant yeasts on plants under salt stress. In this present research, Meyerozyma guilliermondii, a halotolerant yeast, was inoculated with tomato plants followed by salt treatment of four different NaCl concentrations (0, 100, 200, and 300 mM). Our results showed that inoculation of M. guilliermondii increased the chlorophyll biosynthesis and photosynthetic machinery effectiveness under salt stress, contributing to biomass accumulation. Under salt treatment of 300 mM NaCl, the yeast inoculation significantly increased ascorbate concentrations in leaves, yet showed no effects on levels of glutathione and proline. Antioxidant enzymes were affected differently by the yeast inoculation. It was found that the yeast inoculation increased superoxide dismutase (SOD), catalase (CAT), and peroxidase (POD) activities under 300, 100, and 200 mM NaCl, respectively. Total soluble sugar levels increased in inoculated tomato plant leaves; however, there were no significant differences between different NaCl concentrations. Under 300 mM NaCl, the yeast inoculation significantly decreased H2O2 levels and reduced malondialdehyde levels. All together, our results showed that halotolerant yeast M. guilliermondii inoculation might be a strong candidate for regulating tomato growth under salt stress by increasing ability to scavenge reactive oxygen species and chlorophyll intactness, and by strengthening photosynthetic machinery.

A newly synthesized upper rim azocalix[4]arene, namely, 5,11,17,23-tetra[(4-ethylacetoxyphenyl) (azo)]calix[4]arene, CA-AZ was fully characterized and its chromogenic and selective properties for anions are reported. The receptor is selective for the fluoride anion and its mode of interaction in solution is discussed. The kinetics of the complexation process was found to be very fast as reflected in the immediate color change observed with a naked eye resulting from the receptor-anion interaction. Emphasis is made about the relevance in selecting a solvent in which the formulation of the process is representative of the events taking place in the solution. The composition of the fluoride complex investigated by UV/VIS spectrophotometry, conductance measurements and titration calorimetry was 1:1 and the thermodynamics of complexation was determined. The fluoride complex salt was isolated, and a detailed investigation was carried out to assess its ability to remove CO₂ from the air. Recycling of the complex was easily achieved. Final conclusions are given.

An algorithm for the treatment of images affected by both blurring and salt&pepper noise is proposed with a cost only proportional to the number of pixels. The methodology uses a discretization scheme for the Laplace operator multiplied by a suitable nonlinear term depending on the gradient. Even if this approach resembles a diffusion type algorithm, only one step of the procedure is applied, leading to significant time savings. The procedure is successfully tested on some standard black&white natural images.

Plants have acquired sets of highly regulated and complex signaling pathways to respond to unfavorable environmental conditions during evolution. Calcium signaling, as a vital mechanism, enables plants to respond to external stimuli, including abiotic and biotic stresses, and coordinate the basic processes of the growth and development. In the present study, the calcium sensor families, including CBL and CIPK, were investigated in the halophyte plant, Aeluropus littoralis, with a comprehensive analysis. Here, six AlCBL genes, and twenty AlCIPK genes were presented. The analysis of the gene structure and conserved motifs, as well as physicochemical properties, showed that these genes are highly conserved during evolution. The expression levels of AlCBL genes and AlCIPK genes were evaluated under salt stress in leaf and root tissue. Based on the real-time RT-PCR results, AlCIPK gene family had a higher variation in mRNA abundance compared to the AlCBL gene family. The AlCIPKs were found to have a higher abundance in leaves than in roots. The results suggest that the interaction pattern of AlCBL genes with AlCIPK is tissue-specific, and different interactions can be expected in leaves and roots. Based on these patterns AlCIPK3.1 - AlCBL4.1 and AlCIPK1.2 - AlCBL4.4 can interact in root tissue, while the AlCBL10 has the potential to interact with the AlCIPK5, AlCIPK26 and AlCIPK12.3 in the leaf tissue. These findings provide valuable information on the structure and function of calcium sensor families in Aeluropus littoralis a halophyte plant, for future research on the biological function of CBLs and CIPKs on salt stress resistance.

Background: Jerusalem artichoke (Helianthus tuberosus L.) is tolerant to salinity stress and has high economic value. The salt tolerance mechanisms of Jerusalem artichoke are still unclear. Especially in the early stage of Jerusalem artichoke exposure to salt stress, the plant physiology, biochemistry and gene transcription are likely to undergo large changes. Elucidating these changes may be of great significance to understanding the salt tolerance mechanisms of it. Results: We obtained high-quality transcriptome from leaves and roots of Jerusalem artichoke exposed to salinity (300 mM NaCl) for 0 h, 6 h, 12 h, 24 h and 48 h, with 150,129 unigenes and 9023 DEGs (Differentially Expressed Genes). The RNA-seq data were clustered into time-dependent groups (nine clusters each in leaves and roots); gene functions were distributed evenly among the groups convergence. KEGG enrichment analysis showed the genes related to plant hormone signal transduction were enriched in almost all treatment comparisons. Under salt stress, genes belongs to PYL (abscisic acid receptor PYR / PYL family), PP2C (Type 2C protein phosphatases), GH3 (Gretchen Hagen3), ETR (ethylene receptor), EIN2/3 (ethylene-insensitive protein 2/3), JAZ (Genes such as jasmonate ZIM-domain gene) and MYC2 (Transcription factor MYC2) had extremely similar expression patterns. The results of qPCR of 12 randomly selected genes confirmed the accuracy of RNA-seq. Conclusions: Under the impact of high salinity (300mM) environment, Jerusalem artichoke in the seedling stage was difficult to survive for a long time, and the phenotype was severe in the short term. Based on the expression of genes on the time scale, we found that the distribution of gene functions in time is relatively even. Upregulation of the phytohormone signal transduction had a crucial role in the response of Jerusalem artichoke seedlings to salt stress, the genes of abscisic acid, auxin, ethylene, and jasmonic acid had the most obvious change pattern.

Tagetes genus of Composite family consider one of the most favorite floriculture plant. Therefore, of particular interest examine the salt tolerance of this bedding and coloring agent plant. In this research, was report the role of glycinebetaine (GB) in attenuating the adverse impacts of salt stress in African marigold plant, along with their anti-oxidative capacities and biochemical attributes. The salt stressed African marigold (100 and 150 mM NaCl) was treated with GB at 200 mM, beside untreated control plants. According to the obtained results, the growth characters were negatively in salt stressed plants but a mitigate impact of GB were observed in this respect. Obviously, the morphological as well as some physiological characters were reduced with salinity treatments while GB treatment reverses these effects. Overall, the alleviate impact of GB on the negative impact of salt stress was enhanced through improving total phenolic and antioxidant enzyme activity. Further, it is concluded that GB concentration induces the activities of antioxidative enzymes which scavenged ROS increased under saline conditions.

Based on the cloud platform of Google Earth Engine (GEE), this study selected Landsat 5/8 and Sentinel-2 remote sensing images and used Support Vector Machine (SVM) classification method to classify the 35 years of intertidal salt marshes in China, and verified the classification results in combination with field survey. Finally, combining with various driving factors, the reasons and laws affecting the changes of salt marshes species and area were discussed and analyzed. The main results of the study are as follows:The main types of salt marshes plants in China include Phragmites australis, Spartina alterniflora, Suaeda salsa, Scirpus mariquete, Tamarix chinensis, Cyperus malaccensis and Sesuvium portulacastrum. The results salt marshes classification indicated that 166999.32 ha in 1985, 172893.87 ha in 1990, 174952.29 ha in 1995, 125567.51 ha in 2000, 93257.97 ha in 2005, 102539.04 ha in 2010, 96302.92 ha in 2015, and 115722.75 ha in 2019. The main driving factors of salt marsh change from 1985 to 2015 are reclamation, mudflat aquaculture, climate change, coastal zone erosion, invasion of alien species, and natural competition and succession among salt marshes species. The results can be used to quantitatively analyze the salt marshes carbon storage in space and time, and provide data support for the protection of salt marsh wetlands, the restoration of ecological functions and the implementation of "carbon neutral".

As bread is the most consumed food by Tunisian population and the major source of salt, a pilot experience of salt reduction in bread has already begun in Bizerte city. Salt analysis in bread collected from Bizerte city was realized with Volhard titration method. Application of the “salt reduction programme” allowed a gradual decrease of salt content in bread by 35 % during three years without detection by Tunisian consumers. A final salt concentration of 1.1 ± 0.1 g/100 g was then achieved. The establishment of an effective salt reduction strategy with lifestyle education is needed to reduce hypertension that is the first cause of death in Tunisia.

Over the past 150 million years, the Chilean Atacama Desert has been transformed into one of the most inhospitable landscapes by geophysical changes, which makes it an ideal Mars analog that has been explored for decades. However, two heavy rainfalls that occurred in the Atacama in 2015 and 2017 provide a unique opportunity to study the response of resident extremophiles to rapid environmental change associated with excessive water and salt shock. Here we combine mineral/ salt composition measurements, amendment cell culture experiments, and next-generation sequencing analyses to study the variations in salts and microbial communities along a latitudinal aridity gradient of the Atacama Desert. In addition, we examine the reshuffling of Atacama microbiomes after the two rainfall events by comparing with previous researches. Analysis of microbial community composition revealed that soils within the southern arid desert were consistently dominated by Actinobacteria, Proteobacteria, Acidobacteria, Planctomycetes, Chloroflexi, Bacteroidetes, Gemmatimonadetes, and Verrucomicrobia. Intriguingly, the hyperarid microbial consortia exhibited a similar pattern to the more southern desert. Salts at the shallow subsurface were dissolved and leached down to a deeper layer, challenging indigenous microorganisms with the increasing osmotic stress. Microbial viability was found to change with aridity and rainfall events. This study sheds light on the structure of xerophilic, halophilic, and radioresistant microbiomes from the hyperarid northern desert to the less arid southern transition region, as well as their response to changes in water availability. Our findings may infer similar events that happened on the wetter early Mars.

Since the Coronavirus disease (COVID-19) outbreak at the end of 2019, the past two month has seen an acceleration both in and outside China in the R&D of the diagnostics, vaccines and therapeutics for this novel coronavirus. As one of the molecular forces that determine protein structure, electrostatic effects dominate many aspects of protein behaviour and biological function. Thus, incorporating currently available experimental structures related to COVID-19, this article reports a simple python-based analysis tool and a LaTeX-based editing tool to extract and summarize the electrostatic features from experimentally determined structures, to strengthen our understanding of COVID-19's structure and function and to facilitate machine-learning and structure-based computational design of its neutralizing antibodies and/or small molecule(s) as potential therapeutic candidates. Finally, this article puts forward a brief update of the structurally observed electrostatic features of the COVID-19 coronavirus.

As a dominant mangrove species, Kandelia obovata is distributed in an intertidal marsh with an active H₂S release. Whether H₂S participates in the salt tolerance of mangrove plant is still ambiguous although increasing evidence have demonstrated that H₂S functions in plant responses to multiple abiotic stresses. In this study, as an H₂S donor, NaHS was used to investigate the regulatory mechanism of H₂S on salt tolerance of K. obovata seedlings using a combined physiological and proteomic analysis. The results showed that the reduction in photosynthesis (Pn) caused by 400 mM NaCl was recovered by the addition of NaHS (200 μM). Furthermore, the application of H₂S enhanced the quantum efficiency of PSII and the membrane lipid stability, implying that H₂S is beneficial to the survival of K. obovata seedlings under high salinity. We further identified 37 differentially expressed proteins by proteomic approaches under salinity and NaHS treatment. Among them, the proteins related to photosynthesis, primary metabolism, stress response and hormone biosynthesis were primarily enriched. The physiological and proteomic results highlighted that exogenous H₂S up-regulated photosynthesis and energy metabolism to help K. obovata to cope with high salinity. Specifically, H₂S increased photosynthetic electron transfer, chlorophyll biosynthesis and carbon fixation in K. obovata leaves under salt stress. Furthermore, the abundances of other proteins related to metabolic pathway, such as antioxidation (APX, CSD2, PDX1), protein synthesis (HSP, Cpn 20), nitrogen metabolism (GS2, GS1:1), glycolysis (PGK, TPI), AsA-GSH cycle were increased by H₂S under high salinity. These findings provide new insights into the roles of H₂S in the adaptations of mangrove plant K. obovata to high salinity environment.

Iodide is an essential micronutrient present in very small quantities in the human body, with a fundamental action for the adequate synthesis of thyroid hormones, which are critical for cell differentiation, growth and metabolism. In the form of iodide, iodine is widely distributed in the environment, although in an irregular manner, occurring in abundant amounts in the oceans and in coastal areas and scarcely found on islands and mountains. The diet is the main source of iodine, whose intake varies according to the amount present in soil and water and according to eating habits. Governmental policies have been adopted to satisfy and guarantee the necessary daily supply of iodine, such as fortification of industrialized salt for domestic iodine consumption or addition to the bread commonly consumed in a given region, or the offer of iodized oil to the population, or even iodine supplementation through medications. Iodide deficiency is the main avoidable cause of brain damage to fetuses and children, as well as retardation of psychomotor development. Thyroid hormones are almost universally involved in the development and proliferation of fetal neural tissue. Permanent lesions of the cerebral cortex, hippocampus and cerebellum may occur, with loss of, or damage to the brainstem or spinal cord, affecting cortical areas that integrate highly specialized stimuli, which become poorly defined on an anatomical basis, including silent areas of the associative cortex. One of the more significant metabolic problems due to dietary iodine deficiency is the presence of goiter (increased volume of the thyroid gland). Thyroid carcinoma is the most frequent endocrine neoplasia affecting the human species and plasma iodine concentration is related to the development of specific subtypes of this neoplasia. An increased prevalence of follicular carcinoma, a more aggressive tumor, has been observed in areas of iodine deficiency, while the correction of this deficiency is associated with a higher prevalence of papilliferous carcinoma, a less aggressive form. CONCLUSION: An ideal plasma iodide concentration is necessary to insure the proper mental development of fetuses and young children and to minimize the aggressiveness of thyroid cancer from follicular cells in humans.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

Nuclear technologies have a strong potential and a unique role to play in delivering reliable low carbon energy for a future net-zero society. However, to assure the sustainability required for the long-term success, nuclear will need to deliver innovative solutions as proposed in iMAGINE. One of the most attractive features, but also a key challenge for the envisaged highly integrated nuclear energy system is the need for a demand driven salt clean-up system. The work described provides an insight into the interplay between a potential salt clean-up system and the reactor operation in a plutonium started core in a dynamic approach. The results presented will help to optimize the parameters for the salt clean-up process as well as to understand the differences which appear between a core started with enriched Uranium and Plutonium as the fissile material. The integrated model is used to investigate the effects of the initial fissile material on core size, achievable burnup, and long term operation. Different approaches are tested to achieve a higher burnup in the significantly smaller Pu driven core. The effects of different clean-up system throughputs on the concentration of fission products in the reactor salt and its consequences are discussed for general molten salt reactor design. Finally, an investigation of how a plutonium loaded core could be used to provide fuel for future reactors through fuel salt splitting is presented with the outcome that one Pu started reactor of the same size as a uranium started core could deliver fuel for 1.5 new cores due to enhanced breeding. The results provide an essential understanding for the progress of iMAGINE as well as the basis for inter-disciplinary work required for optimizing iMAGINE.

Zinc nanoparticles (ZnNPs) open new opportunities for biomedical applications as a strategy against microbes and dye removal in an efficient way. The composite ZnNPs using Rhododendron arboreum (R. arboreum) stem bark were synthesized and characterized for UV-visible spectroscopy (UV-vis), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The synthesized nanoparticles showed zones of inhibition of 23±0.09, 18±0.1 and 16±0.05 mm, against the Klebsiella pneumoniae (K. pneumoniae), Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli strains. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) values against K. pneumoniae, S. aureus, and E. coli were found to be 34±0.21 and 72.71±0.47, 47±0.11 and 94.86±0.84 and 94±0.18 and 185.43±0.16 µg/mL, respectively. The biosynthesized ZnNPs resulted in significant eradication of the outer and inner membranes of the bacterial cells. Likewise, the synthesized ZnNPs showed time-dependent photocatalytic degradation activity and revealed 65% methyl orange dye degradation with an irradiation period of 6 hours. The findings of this study suggest the suitability of the novel R. arboreum stem bark-based ZnNPs as an effective ameliorant against bactericidal activities and photocatalysts for the removal of hazardous water contaminants.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

The UV/Vis absorption energies (νmax) of different solvatochromic probes measured in co-solvent/water mixtures are analysed as a function of the average molar concentration (Nav) of the solvent composition. Nav is discussed in terms of the underlying average molar mass (mol average or mass average) of the mixture. ET(30) of Reichardt`s dye B30 is the focus of the analysis. Methanol, ethanol, 1,2-ethanediol, 2-propanol, 2-methyl-2-propanol, 2-butoxyethanol, formamide, N-methylformamide (NMF), dimethylformamide (DMF), N-formylmorpholine (NFM), 1,4-dioxane and DMSO were used as co-solvents. Significant linear dependencies of ET(30) as a function of Nav can be demonstrated for formamide/water, 1,2-ethanediol/water, NMF/water and DMSO/water mixtures over the whole composition range. These mixtures belong to the group of solvents that do not enhance the water structure according to the Marcus classification. The specifics of the 1,4-dioxane/water mixtures are discussed. For alcohol/water mixtures with enhanced water structure, the influence of the solvent microstructure on ET(30) is particularly evident.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

Zinc oxide (ZnO) nanoparticles (NPs) were synthesized using Rosmarinus officinalis leaf extract at 80 ° C (ZnO-80) and 180 ° C (ZnO-180). The biosynthesized ZnO NPs were characterized and their photocatalytic activity was evaluated for the degradation of methylene blue (MB) and crystal violet (CV) under sunlight irradiation. The results of the characterizations by XRD, TEM and SEM showed that the size of the NPs of ZnO-80 was smaller than that of ZnO-180 which exhibited flakier agglomerated spherical structures. Photocatalytic tests showed ZnO-80 which was prepared by a cheap and easy procedure compared to ZnO-180 effectively degrades MB and CV dyes under sunlight. The superior performance of ZnO-80 over ZnO-180 can be explained by the differences in their textural properties. This is because ZnO-80 has a smaller crystallite size, a specific surface area and a higher pore volume than ZnO-180. Fourier-transform infrared spectroscopy (FTIR) analyzes revealed that both samples contained an adsorbed carboxylate group (COO-), and accordingly a mechanism was proposed for the formation of ZnO NPs that include the carboxyl group.

The presence of azo dyes in textile effluents is an issue of major concern due to their potential impact on the environment and human health. In this study we investigate the photocatalytic degradation under visible light of Reactive Violet 5 (RV5), an azo dye widely used in the textile industry. A preliminary screening of different titania-based catalysts was carried out to identify the best candidate for RV5 removal. The selected catalyst was then tested in a stirred and aerated lab-scale reactor illuminated with a light LED source (λmax = 460 nm). The effects of pH, catalyst load and hydrogen peroxide additions on the efficiency of dye removal were evaluated. Under the best conditions (pH 10, 3 g/L of catalyst and 60 mM hydrogen peroxide), the dye solution was completely decolorized in about 2 h. Overall, the results obtained suggest that the proposed process may represent a suitable method for the removal of RV5 from textile effluents.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

To investigate the effect of prohexadione-calcium (Pro-Ca) primed on seed germination and seedling growth of oilseed rape under salt stress, to alleviate the inhibition of soil salinization on the growth of oilseed rape, and to improve the sustainability of agricultural production. Using Huayouza 158R and Huayouza 62 as test materials, the regulation of seed germination and seedling growth under the stresses of 0, 100, and 150 mM NaCl (S0, S100, and S150) was investigated after the primed of Pro-Ca. We conducted six treatments, S0: non-primed + 0 mM NaCl, PCS0: Pro-Ca primed + 0 mM NaCl, S100: non-primed + 100 mM NaCl, PCS100: Pro-Ca primed + 100 mM NaCl, S150: non-primed + 150mM NaCl, Pro-Ca+S150: Pro-Ca primed + 150 mM NaCl. The results showed that salt stress inhibited seed germination and seedling growth, and Pro-Ca primed significantly increased the germination index and vigor index of oilseed rape seeds. The average germination time and malondialdehyde (MDA) content were significantly reduced, which resulted in the optimal initiation fiddling concentration of 8mg·L-1. The morphological parameters of oilseed rape decreased significantly under salt stress, with leaf area decreasing by 70.69% and 75.03% and total chlorophyll content decreasing by 18.55% and 18.68% at S150. With the rise of salt stress, the changes of each photosynthetic parameter were somewhat similar, and Pn, Gs, Ci, and Tr continued to decline, indicating that the effects of salt stress on photosynthesis in oilseed rape might be mainly attributed to stomatal restriction and inhibition of photosynthetic pigment synthesis. While Na+ and MDA contents increased significantly, reaching a peak at S150, indicating that Na+ content increased significantly under salt stress, which resulted in the slow growth of oilseed rape and weak plants under the influence of Na+ salt damage. After Pro-Ca primed, leaf area and photosynthetic pigment synthesis increased, and the initiation treatment promoted the rise of Pn, Gs, Ci, and Tr under salt stress. The Na+ content decreased by 7.29% and 6.96% in PCS100 compared with S100, decreased by 9.23% and 25.02% in PCS150 compared with S150, and increased in K+ and Mg2+ after Pro-Ca primed. At this time, the antioxidant enzyme activities increased, and the MDA content and relative conductivity decreased. It was concluded that Pro-Ca primed improved the photosynthetic capacity of oilseed rape by promoting leaf growth, stomatal opening, and photosynthetic pigment synthesis. At the same time, reducing Na+ content and promoting K+ and Mg2+ absorption and antioxidant enzyme activities together alleviate salt damage and improve salt tolerance of oilseed rape.

Amylin, also known as islet amyloid polypeptide (IAPP), is a metabolic homeostasis-related hormone that is produced and released by the β cells of the pancreas, the same cells that produce insulin. Insulin-degrading enzyme (IDE) is a protease enzyme that plays an essential role in the breakdown and degradation of various peptides, including insulin and amylin. Direct binding & interaction between amylin and IDE is inextricably linked to the degradation of amylin, and research and development effort in this area is crucial to understand the potential therapeutic implications of disrupting the IDE-amylin interaction in the context of conditions where metabolic homeostasis needs to be regulated, such as diabetes and obesity. Here, this article incorporates currently available experimental complex structure of amylin and IDE, and delves deep into the interstructural biophysics underlying the binding interface of the two interacting partners. With a set of comprehensive structural biophysical analysis, this article identified an intriguing region of high electrostatic potential indicative of strong binding sites between the first N-terminal lysine (Lys1, K1) residue of amylin and Glu341 (E341) of IDE. This unique electrostatic hotspot presented herein paves the way for the rational design of drug-like small molecules that can selectively disrupt this interaction, offering a targeted therapeutic strategy for improved metabolic homeostasis, particularly for patients with diabetes and obesity.