Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

Introduction of Cl- and O- atoms into C4-vinyl carbocations was studied by X-ray diffraction analysis and IR spectroscopy. Chlorine atoms are weak electron acceptors in ordinary molecules, but within vinyl carbocations, manifest themselves as strong electron donors that accept a positive charge. The attachment of a Cl atom directly to a C=C bond leads to an increase in the e-density on it, exceeding that of the common double bond. The positive charge should be concentrated on the Cl atom, and weak δ- may appear on the C=C bond. More distant attachment of the Cl atom—to a C atom adjacent to the C=C bond—has a weaker effect on it. If two Cl atoms are attached to the Сγ atom of the vinyl cation, as in Cl2СγСδHСαHCH3, then the cation switches to the allyl type with two practically equivalent and almost uncharged СγСδСα bonds. When such a strong nucleophile as the O atom is introduced into the carbocation, a protonated ester molecule with a C-O(H+)-C group and a C=C bond forms. Nonetheless, in the future, there is still a possibility of obtaining carbocations with a non-protonated C-O-C group.

The fixation and activation of the dinitrogen molecule, N2 by hexametallic clusters of the general formula {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 (L = CH2-, NH2-, PH2-, OH-, SH-, BH2- and NH2-, M = Ru(II) or Os(II)) were scrutinized by means of density functional theory calculations. In these systems, the dinitrogen molecule, acts as a ligand that bridges the two opposite facing triangular metallic rings, cyclo-M3 of the {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 clusters The hexametallic clusters, that mimick the six Fe cluster of nitrogenase, were found to strongly activate N2, converting it into a hydrazido-like group, N24-. This is substantiated by the calculated N-N bond lengths, Re(N-N) and the stretching frequencies of the N-N bond of dinitrogen, vs(N-N) found in the ranges 1.299 – 1.487 Å and 780 – 1270 cm-1 respectively. Based on the Re(N-N) and vs(N-N) values, the dinitrogen activation depends upon the nature of the hexametallic cluster. Accordingly, the Os(II) clusters were found to activate more strongly the dinitrogen molecule as compared to their Ru(II) counterparts. The nature of the ligand L also affects the extent of the N2 activation by the hexametallic clusters, which follows the order BH2- < NH2- < OH- < CH2- < NH2- < PH2-, SH- for M = Ru(II) and the order BH2- < NH2- < OH- < NH2- < CH2- < PH2- < SH- for M = Os(II). Thus, the strongest N2 activation is observed for the {[(μ2-SH)Os)]6(μ-η1:η3-Ν2)}+6 cluster and the weakest for the {[(μ2-BH)Ru)]6(μ-η1:η3-Ν2)}0 cluster. The calculated Nitrogen-15 NMR isotropic chemical shielding tensors, σiso(15N) exhibit shielding (upfield) upon N2 fixation to the metal centers of the hexametallic clusters, as a results of electron density transfer towards its constituent N nuclei. A multitude of electronic charge distribution partitioning schemes were applied to assist in delineating the bonding properties of the {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 clusters. Accordingly, it is found that there is a donation/backdonation interaction between the bridging N2 ligand and the two opposing cyclo-M3 rings located on either side. The dinitrogen ligand forms six bonds of mixed covalent/electrostatic nature with the six metal centers of the {[(μ2-L)M)]6)}0/+6 clusters.

The (benzylthio)acetic acid (HBTA) and some aminopyrimidines, namely 2-aminopyrimidine (2-AP), 5-aminopyrimidine (5-AP), 2-amino-4,6-dimethylpyrimidine (2-A-4,6-DMP) and 2,4,6-triaminopyrimidine (2,4,6-TAP), were successfully embodied as structural units into the construction of a total of four novel supramolecular organic frameworks. The received crystalline solids were inspected by single crystal X-ray diffraction (SC XRD) in order to obtain insight into the structural and supramolecular facets. The SOFs deriving from 2-AP, 5-AP as well as 2-A-4,6-DMP crystallize in the form of true co-crystals (1-3), while the one originating from 2,4,6-TAP crystallizes as salt solvate (4). The SC XRD results indicated the different contents of structural residues present in the asymmetric units of the crystals 1-4 despite the using the same molar ratio of molecular co-formers in each case. The molecular structures of co-crystals 1-3 consist of either one neutral residue of each starting components (1 and 3) or a half nonionized residue of aminopyrimidine ingredient and one neutral residue of acidic specie (2). The asymmetric unit of salt solvate 4 is composed of two ionized residues of each co-former (two 2,4,6-TAP+ cations and two BTA- anions) and one MeOH solvent molecule. The most extensive H-bonding network is observed in the crystal structure of salt solvate 4. The relevant molecular ingredients in co-crystals 1-3 are mainly hold together by the neutral Ocarboxylic–H···Npyrimidine and Namine–H···Ocarboxylic H-bonds. In the case of aggregate 4, the corresponding ionic residues are predominantly sustained by the charged-assisted Npyrimidinium–H···Ocarboxylate and Namine–H···Ocarboxylate hydrogen interactions. The MeOH solvent incorporated into the crystal lattice of adduct 4 is also involved in H-bonding by simultaneously serving as the single donor in OMeOH–H···S and the single acceptor in Namine–H···OMeOH H-bonds afforded the structural diversity within the 2,4,6-TAP+ cations and BTA- anions. Other weaker sets of additional non-covalent contacts existing in the crystal structures of analyzed conglomerates are involved in the self-assembly, stabilization and expansion of total supramolecular organic frameworks. The fact of the formation of non-covalent bonded supramolecular organic frameworks in question is also reflected in corresponding results obtained through elemental analysis (EA), Fourier transform infrared spectroscopy (FT−IR) and thermal analysis (TG/DSC).

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Accurate and reliable mid-long runoff prediction (MLTRP) is of great importance in water re-sources management. However the MLTRP is not suitable in each basin and how to evaluate the applicability of MLTRP is still a question. Therefore, the total mutual information (TMI) index is developed in this study based on the predictor selection method using mutual information (MI) and partial MI (PMI). The relationship between the TMI and the predictive performance of five models is analyzed by applying five models in 222 forecasting scenarios in Australia. The results over 222 forecasting scenarios demonstrate that, compared with the MI, the developed TMI index can better represent the available information in the predictors, and has more significant negative correlation with the RRMSE with the correlation coefficient between -0.62 and -0.85. This means the model's predictive performance will become better along with the increase of TMI, and there-fore the developed TMI index can be used to evaluate the applicability of MLTRP. When TMI is more than 0.1, the available information in the predictors can support the construction of MLTRP models. In addition, the TMI is used to partly explain the difference of predictive performance among five models. In general, the complex models, which can better utilize the contained infor-mation, are more sensitive to the TMI, and have more significant improvement in terms of predic-tive performance along with the increase of TMI. This research can provide support for the study of MLTRP.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.