Multiple Gateways (GWs) provide network connectivity to Internet of Things (IoT) sensors in a Wide Area Network (WAN). The End Nodes (ENs) can connect to any GW by discovering and acquiring its periodic beacons. This provides GW diversity and hence improves coverage. If the GWs are within vicinity to each other, and they keep sending periodic beacons to be discovered, the result is interference and collisions. In this study, the impact of such intra-network interference is analyzed to determine the maximum number of GWs that can co-exist within a given urban neighborhood. The paper shows the relationship between beacon collisions and the resulting packet loss rates in a given urban environment. The expected collision rates are calculated for the Medium Access Control (MAC) layer. The eventual packet loss rates are calculated with the MAC and Physical (PHY) layers combined. For this purpose, a new co-channel interference model is presented. The model calculates the average Carrier to Interference ratio (C/I) averaged across all the colliding events. It takes into account the partial overlap durations and the relative power of each colliding signal. The model shows that a collision does not always cause a packet loss. Packet losses occur if there is a collision and if the C/I is below a threshold. The performance evaluation is presented using a combination of analytical and simulation methods. The analytical methods provide the theoretical foundation, and have been used to validate the simulation results. Furthermore, the system models are developed from experimental data obtained from measurements with real hardware. Numerical results are provided with a low bit rate Gaussian Frequency Shift Keying (GFSK) modulation at the PHY layer, which is derived from the IEEE 802.15.4 standard specification. This paper provides guidance on selecting the right GFSK modulation parameters for such low bit-rate and narrow bandwidth IoT applications. The analysis and simulation results show that larger beacon intervals help in reducing beacon loss rates, at the cost of larger beacon acquisition latency. On the flip side, the gateway discovery latency reduces with increasing GW density thanks to abundance of beacons.

This research work uses a simplified approach to combine location information from beacons propagation signal interaction with a mobile device with local building information to give real-time location and guidance to a user inside a building. This is an interactive process with visualisation information that can help user’s orientation inside unknown buildings and the data stored from different users can provide useful information about users movements inside a public building. Beacons installed on the building at specific pre-defined position emit signals that give a geographic position with an associated imprecision, related with Bluetooth’s range. This uncertainty is handled by building layout and users’ movement in a developed system that maps users’ position, gives guidance and store user movements. This system is based on an App (Find Me!) for Android OS (Operating System) which captures the Bluetooth Low Energy (BLE) signal coming from the beacon(s) and shows, through a map, the location of the user ‘s smartphone and guide him to the desired destination. Also, the beacons can deliver relevant context information. The application was tested by a panel of new and habitual campus users against traditional wayfinding alternatives yielding navigation times about 30% smaller, respectively.

In this study, we propose an augmentation method for machine learning based on relabeling data in caregiving and nursing staff indoor localization with Bluetooth Low Energy (BLE) technology. Indoor localization is used to monitor staff to patient assistance in caregiving and to gain insights into workload management. However, improving accuracy is challenging when there is a limited amount of sensor data available for training. In this paper, we propose a data augmentation method to reuse the Received Signal Strength (RSS) from different sensors by relabeling to the sensors with less samples resolving data imbalance. Standard deviation and Kullback-Leibler divergence between minority and majority class are used to measure signal pattern to find matching sensors to relabel. By matching sensors between classes, two variation of relabeling are implemented specifically full and partial matching. The performance is evaluated using real world dataset we collected for five days in a nursing care facility installed with 25 BLE beacons. Random Forest model is utilized for location recognition, and performance is compared using the weighted F1-score to account for class imbalance. By increasing the sensor data with our proposed relabeling method for data augmentation, we achieved higher minority class F1-score as compared to augmentation with Random Sampling, Synthetic Minority Oversampling Technique (SMOTE) and Adaptive Synthetic Sampling (ADASYN). Our proposed method utilizes collected sensor data by leveraging majority class samples. Full matching demonstrated a 6 to 8% improvement from the original baseline overall weighted F1-score.

Unlike aerial or terrestrial navigation, the Global Navigation satellite system (GNSS) is not available underwater. This is a big challenge for underwater navigation. The inertial navigation system (INS) aided by the single-beacon acoustic positioning system (APS) provides one solution, but the long-range case is limited by low SNR conditions. Inspired by passive synthetic aperture detection, we proposed a new tightly coupled navigation algorithm based on spatial synthesis and one-way-travel-time (OWTT) range measurement. We design two estimators: the DOA/Range estimator using the model-based method and the tightly coupled INS/APS navigation estimator. Based on the improved UKF, all information is combined. Simulation is carried out in MATLAB. Compared with range-only tightly coupled INS/APS navigation, synthetic long baseline (SLBL) algorithm and Doppler velocity logger (DVL) aided centralized extended Kalman filter (CEKF) based single beacon INS/OWTT navigation, the proposed method's performance is proven. The main contributions of this work are: 1. Propose a new architecture of underwater integrated navigation; 2. Apply the passive acoustic detecting method in the navigation to improve accuracy. 3. Apply the tightly coupled method to improve availability.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

This paper studies the performance improvement of the IEEE 802.15.4 nonbeacon-enabled mode originated by the inclusion of the Request-To-Send/Clear-To-Send (RTS/CTS) handshake mechanism resulting in frame concatenation. Under IEEE 802.15.4 employing RTS/CTS, the backoff procedure is not repeated for each data frame sent but only for each RTS/CTS set. The maximum throughput and minimum delay performance are mathematically derived for both the Chirp Spread Spectrum and Direct Sequence Spread Spectrum Physical layers for the 2.4 GHz band. Results show that the utilization of RTS/CTS significantly enhances the performance of IEEE 802.15.4 applied to healthcare in terms of bandwidth efficiency.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.