Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. The main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Data presented here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

Abstract : This paper presents the investigation of biomechanical behaviour of sheep heart fibre using uniaxial tests in various samples. Non-linear Finite Element models (FEA) that are utilised in understanding mechanisms of different diseases may not be developed without the accurate material properties. This paper presents uniaxial mechanical testing data of the sheep heart fibre. The mechanical uniaxial data of the heart fibre was then used in fitting four constitutive models including the Fung model, Polynomial (Anisotropic), Holzapfel (2005) model, Holzapfel (2000) model and the Four-fibre Family model. Even though the constitutive models for soft tissues including heart myocardium have been presented over several decades, there is still a need for accurate material parameters from reliable hyperelastic constitutive models. Therefore, the aim of this research paper is to select five hyperelastic constitutive models and fit experimental data in the uniaxial experimental data of the sheep heart fibre. A fitting algorithm was made used to optimally fitting and determination of the material parameters based on selected hyperelastic constitutive model. In this study, the evaluation index (EI) was used to measure the performance and capability of each selected anisotropic hyperelatic model. It was observed that the best predictive capability of the mechanical behaviour of sheep heart fibre the Polynomial (anisotropic) model has the EI of 100 and this means that it is the best performance when compared to all the other models.

Tendons transmit forces from muscles to bones through joints. Typically, tendons and muscles work together to innovate a particular type of motion. Therefore, in order for the tendons to find attachment to the bones, they are naturally adapted as much thinner strands than the muscles that they serve. Thus, they are often subjected to much higher stresses than the muscles that they actually serve in any given action. As a result, tendons are susceptible to injuries that may lead to a permanent dysfunction in joint mobility due to the fact that the scar tissue that forms after healing does not often have the same mechanical properties of the original tissue. It is, therefore, very important to understand the mechanical response of tendons. This paper examines the performances of two viscoelastic standard nonlinear models in modelling the elastic and plastic behaviour of the tendon in the light of a well-known hyperelastic Yeoh model. The use of the Yeoh model is more for validating the performances of the viscoelastic models within the elastic region rather than for comparison purposes. Yeoh model’s selection was based on its superior performance in modelling the elastic phase of soft tissue as reported in previous studies combined with its simplicity. The results show that the two standard nonlinear solid models perform extremely well both in fitting accuracies and in correlating stress results. The most promising result is the fact that the two standard nonlinear models can model tendon behaviour in the nonlinear plastic region. It is also noted that the two standard nonlinear models are physically insightful since their optimisation parameters can be easily interpreted in terms of tendon elasticity and viscoelastic parameters.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

This article presents raw data of biaxial tensile measurements of rat heart passive myocardium conducted in lab scale environment. The passive myocardium of the rat was divided into three regions, namely: left ventricle, mid-wall and right ventricle. The biaxial dataset of passive rat myocardia is presented as stress vs strain of the passive rat myocardium in various regions. The determination of valid material properties of the heart plays an important role in the development computational models. These computational models are useful in studying various scenarios and mechanisms of heart diseases. In addition, valid and accurate materials are critical in the development of new therapies. The dataset presented here is useful in the area of soft tissue mechanics including studying the mechanisms of heart diseases such as myocardial infarction. Accordingly, the evaluation of stress and strain in left ventricle, mid-wall and right ventricle was performed.

A better understanding of diseases progress in tissues vest on the accurate understanding of tissues under mechanical loading. Also, development of therapies for injuries may depend on the available mechanical data for soft tissues. In this study, the raw data of biaxial tensile testing of sclera soft tissue is presented in this paper. Biaxial mechanical testing of soft tissues presents details understanding of how soft tissues behave when compared to uniaxial testing. Biomechanical properties of soft tissues are vital in the development of accurate computational models. Reliable computational models of studying mechanisms of diseases depends mainly on the accurate and more details mechanical behavior of soft tissues. These accurate and detailed computational models may be utilized to further develop the understanding and therapies of various diseases. The mechanical tensile testing was conducted on the passive sheep sclera. Engineering stress vs strain of several samples of the sheep sclera are further presented determined from force and displacement experimental data. The goal of this paper is to make available biaxial data of sheep sclera soft tissue that can be further utilized.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

Heart myocardia are critical to the facilitation of heart pumping and blood circulating around the body. The biaxial mechanical testing of the Left Ventricle (RV) is utilised to build the computa-tional model of the whole heart with little importance given to the unique mechanical properties of Right Ventricle (RV) and Mid-wall (MDW). Most of those studies focussed on the LV of the heart, and then apply the obtained characteristics with a few modifications to the right side of the heart. However, that view has been contested over time with the realisation that the right side of the heart possesses its own unique mechanical properties that are widely distinct from that of the left side of the heart. This paper is aimed at reporting and evaluating the passive mechanical property dif-ferences in the three main walls of the rat heart based on biaxial tensile test data. Fifteen mature Wistar rats weighing 225 ± 25 g were euthanised by inhalation of 5 % halothane. The hearts were excised after which all the top chambers comprising the two atria, pulmonary and vena cava trunks, aorta and valves are all dissected out. Then 5 x 5 mm sections from the middle of each wall were carefully dissected with a surgical knife to avoid over-prestraining the specimens. The specimens were subjected tensile test. The elastic moduli, peak stresses in the toe region and stresses at 40 % strain, anisotropy indices as well as the stored strain energy in the toe and linear region up to 40 % strain are used for statistical significance tests. The following are the main findings of this study: (1) LV and MDW tissues have relatively shorter toe regions of 10 - 15 % strain as compared to RV tissue whose toe region extends up to twice as much as that (2) LV tissues have higher strain energy storage in the linear region despite being lower in stiffness than the RV (3) the MDW has the highest strain energy storage along both directions which might be directly related to its high level of anisotropy. These findings, though for a specific animal species at similar age and around the same body mass, emphasize the importance of application of wall specific material parameters to obtain accurate ventricular hyperelastic models. The findings further enhance our understanding of the desired mechanical behaviour of the different ventricle walls.