Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

The mortar’s composition, porosity, mechanical properties, entryways’ orientation, and condi-tioning status of the tunnels made by the Najdian Termite, Microtermes najdensis located at Hada Al-Sham village, Makkah Province, Saudi Arabia were studied. The most prevalent infected tim-ber trees by this pest were Tamarix aphylla, Pithecellobium duce, Zizyphus spina christi, Leucaena leu-cocephala, Ficus infectoria, and Phoenix dactylifera. Climate, soil, healthy wood (Wh), and termite nest skeleton (TNS) were the four components of the termite system that were investigated physi-cally, chemically, spectroscopically, and by FTIR, XRD, SEM, and TEM. It was noticed that the entryways of the termite nests are located at the southwest direction for all the infected trees studied at Hada Al-Sham village that promotes better ventilation. Concerning to the air-conditioning status within the their nest, the internal temperature (IT) was found to be milder than that for its analogous value for the outer temperature (OT) in which the IT was wormer than OT during cold durations, while it was colder than the hottest OT in hot days and vice versa. The IT’s trend had more constantancy with minor fluctuations compared to that for the OT. Moreo-ver, the IT was found to be tended to the upper OT’s limit otherwise its colder one. This finding means that these termite species prefer the hotter atmospheres comparing the colder circumstanc-es. Lignin is the prominent tracer of the organic matter used as a binder for the TNS due to its gluing ability, resistance to enzymatic degradation by the termites and their accompanied fungal community habituating the nests. The presence of both microcrystalline cellulose (MCC) and nanocrystalline cellulose (NCC) was discovered for the first time in the nest mortar reinforcing Klason lignin as the main binder. Their presence was proved by FTIR, XRD, SEM and TEM anal-yses and we satisfied that they were naturally-synthesized by the action of enzymatic hydrolysis excreted by the termites and their accompanied fungal community habituating the nests. The gross heat of combustion (GHCs) of the Wh and TNS were studied to try to find an important uti-lization of the infected woods as renewable energy resources instead of disposal them without economic benefits. These findings may be used for interpreting the durability of the termite nests to the different environmental stresses. Biomimicry of the termites’ nest from the perspective of its magic mortar with a suitable permeability, the entryways’ orientation, and the air-conditioning status can lead to modify the current construction’s designs to be more green and ecofriendly.

Corn starch-based nanocomposite films usually have low moisture barrier properties. The addition of virgin coconut oil (VCO) as a hydrophobic component can improve the nanocomposite film's characteristics, especially the film's permeability and elongation properties. This study aimed to determine the role of VCO with various concentrations (0,3,5 wt%) on the physical, mechanical, and water vapor transmission characteristics of corn starch/NCC-based nanocomposite films. The results showed that the concentration of 3 wt% VCO was most effective in reducing the WVTR value of nanocomposite films with a value of 4.721 g/m2.h. While the value of tensile strength was 4.243 MPa, elongation 68.58%, modulus of elasticity 0.062 MPa, thickness 0.219 mm, lightness 98.77, and water solubility 40.51%. However, the addition of 5 wt% VCO was more effective in increasing the elongation properties of the film. The addition of VCO gave the appearance of a porous film surface and a finer structure was formed. The FTIR test on corn starch nanocomposite films with the addition of VCO did not show any new absorption peaks. The results of this study may provide opportunities for the development of nanocomposite films as biodegradable packaging in the future.

Nanostructured materials have already become an integral part of our daily life. In many applications ion mobility decisively affects the performance of, e.g., batteries and sensors. Nanocrystalline ceramics often exhibit enhanced transport properties due to their heterogeneous structure showing crystalline (defect-rich) grains and disordered interfacial regions. In particular, anion conductivity in nonstructural binary fluorides easily exceeds that of their coarse-grained counterparts. To further increase ion dynamics aliovalent substitution is a practical method to influence the number of (i) defect sites and (ii) the charge carrier density. Here, we used high energy-ball milling to incorporate Y³⁺ ions into the cubic structure of SrF₂. As compared to pure nanocrystalline SrF2 the ionic conductivity of Sr_1-xYxF_2+x with x = 0.3 increased by 4 orders of magnitude reaching 0.8 x 10 ^-5 S/cm^-1 at 450 K. We discuss the effect of YF₃ incorporation on conductivities isotherms determined by both activation energies and Arrhenius pre-factors. The enhancement seen is explained by size mismatch of the cations involved, which are forced to form a cubic crystal structure with extra F anions if x is kept smaller than 0.5

This manuscript presents the result of utilizing cellulose as a template to prepare na-nosized WO3-NiWO4 and its application as co-catalysts in Pt/WO3-C and Pt/WO3-NiWO4-C for ethanol and glycerol electro-oxidation. Microcrystalline cellulose was hydrolyzed with phosphotungstic acid (H3PW12O40) to prepare the nanosized template of crystalline cellulose. Next, the template was impregnated with Ni(NO3)2, rendering a precursor mate-rial that is subsequently air-calcinated, removing the carbon-template material to obtain the nanometric WO3 and NiWO4. Elemental analysis confirmed the coexistence of nickel and tungsten, whereas the thermal analysis evidenced the high thermal stability of these materials. The X-ray diffractograms displayed crystal facets of WO3 and, when added Ni, of NiWO4. The transmission electron micrographs corroborated the formation of na-nosized particles with average particle sizes close to 50 nm. Finally, to apply this material, Pt/WO3-C and Pt/WO3-NiWO4-C were prepared and used in ethanol and glycerol electro-oxidation in alkaline medium, observing a promotional effect of the oxide and tungstate by reducing the onset potential and increasing the current density. These materials show great potential to produce clean electricity or green hydrogen contributing to energetic transition.

The gap of standardization for conducted and field coupled electromagnetic interferences (EMI) in the 2–150 kHz frequency range can lead to Electromagnetic Compatibility (EMC) problems. This is caused by power systems such as PWM controlled rectifiers, photovoltaic inverters or charging battery units in electric vehicles. This is a very important frequency spectral due to interferences generate in a wide range of dives and, specifically, communication problems in the new technologies and devices incorporated to the traditional grid to convert it into Smart Grid. Consequently, it is necessary to provide new solutions to attenuate this kind of interferences, which involve finding new materials able to filter the electromagnetic noise. This contribution is focused on characterizing the performance of different cable ferrite compositions in order to determine the effectiveness of most common materials such as MnZn and NiZn and a new range based on nanocrystalline solutions. This analysis procedure is carried out through two methods: theoretical method by determining the insertion loss through measuring impedance parameter and proposing a new empirical technique based on measuring directly the insertion loss parameter. Therefore, the main aim of this characterization process is to determine the performance of these cable ferrites to reduce the interferences in this controversial frequency range. From the results obtained, it is possible to deduce that nanocrystalline cable ferrites provide the best performance to filter the electromagnetic noise in the 2-150 kHz frequency range.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.