The remediation of dredged marine sediments contaminated by heavy metals has drawn increasing attention worldly. The immobilization was regarded as a promising method to reduce adverse impacts on marine ecosystem. In this study, kaolinite and limestone were used as amendments to immobilize heavy metals (e.g. Zn, Pb and Cu) respectively in dredged marine sediments collected from the coastal zone adjacent to Tianjin Port in Bohai Bay. The sequential extraction procedure was applied to identify the mobility of heavy metals and further to evaluate the immobilization effect of amendments. The physical-chemical properties of sediments, such as pH, electrical conductivity (EC), salinity, and total organic carbon (TOC), were also measured to better understand their influence on heavy metals’ mobility. In addition, the compositions of clay minerals were also analyzed to identify the transformation process of minerals in the sediments. The results of sequential extraction procedure indicated that mobile fractions of heavy metals were converted into relatively stable fractions because of the two amendments. In addition, EC, salinity and TOC decreased moderately while no obvious variations of pH in the sediments were observed with the addition of the the kaolinite and the limestone. The percentage of montmorillonite decreased to minimum value while that of chlorite increased gradually during the experimental periods for 40 days probably due to complexation reaction. It was confirmed that both kaolinite and limestone can effectively reduce the mobility and bioavailability of heavy metals, particularly for Zn, generally, limestone has a better immobilization effect compared with kaolinite.

Under batch experiment conditions, this work seeks to successfully remove Diclofenac-Na (DCF-Na) from an aqueous solution utilizing a composite sorbent made of Bentonite, Kaolinite clay, and Worm casting (BKW). This study investigated the structural modification of the H₃PO₄ Modified Clay by X-ray fluorescence and the effect of selected adsorption factors – DCF-Na concentration and modified BKW composite dosage. The concentration equilibrium data was used to study six isotherm models. Freundlich isotherm model better explained the adsorption of DCF-Na onto modified BKW composite with a correlation coefficient close to 1. Kinetics models were examined, and the Elovich model gave a better fit than other kinetic models studied. Mass diffusion mechanisms and thermodynamics studies were successfully carried out. The enthalpy change values evaluated were negative, which revealed the spontaneity of DCF-Na remediation onto modified BKW, and that DCF-Na adsorption is exothermic and occurred through a physisorption process.

The presence of clays in copper minerals has a significant negative impact during their processing, leading to low recoveries during the flotation process. In saline environments such as seawater, the presence of clays contribute to an increase in operational problems caused by salinity, a decrease in the grade of the copper concentrate, alteration of the rheology of the mineral pulp, a decrease in the selectivity of copper during the flotation process, a reduction in the quality of clarified water, and excessive corrosion of metallic components. This study explores the electroflotation of kaolinite and montmorillonite clays in NaCl solutions using a modified Hallimond tube coupled with Ti Gr. 2 electrodes for bubble generation via water electrolysis, and the corrosion analysis of these electrodes applying the superposition model. The electroflotation results show recovery of clays close to 72.68% for kaolinite, 88.44% for montmorillonite, and 67.36% for a mixtures of both clays. The presence of clays helps reduce the corrosive effects of Ti Gr. 2 from 0.069 A/m2 in NaCl to 0.0073 A/m2 in NaCl with montmorillonite clay.

Fingerprints are essential for human identification and are valuable tools in criminal investigations. The pursuit of new materials for digital printing is expanding, with increasing interest in natural compounds such as bixin, sourced from annatto seeds. Despite its traditional use as a natural dye with medicinal properties, the potential of bixin in papilloscopy remains largely untapped. In this study, we meticulously extracted bixin from annatto seeds and meticulously developed composites incorporating zinc carbonate (bixin/ZnCO3) and kaolinite (bixin/kaolinite). UV-visible spectroscopy was used for characterization, and the extracted bixin showed absorption peaks at 429, 453, and 481 nm, which were very similar to standard peaks at 429, 457, and 487 nm. The two samples also had the same retention times (7.07 min) according to further liquid chromatography analysis. Sweat pores were easier to detect thanks to the effectiveness of the bixin/ZnCO3 and bixin/kaolinite composites in creating high contrast sebaceous and natural latent fingerprints. These results highlight the composites’ potential as novel and fascinating instruments for papilloscopy applications, which might also improve forensic investigations.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.