The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

Here, we report on ZnO nanoparticles (NPs) generated by nanosecond pulsed laser (Nd:YAG, 1064 nm) through ablation of metallic Zn target in water and air and their comparative analysis as potential nanomaterials for biomedical applications. The prepared nanomaterials were carefully characterized in terms of their structure, composition, morphology and defects. It was found that in addition to the main wurtzite ZnO phase, which is conventionally prepared and reported by others, the sample laser-generated in air also contained some amount of monoclinic zinc hydroxynitrate. Both nanomaterials were then used to modify model wound dressings based on biodegradable poly-L-lactic acid. The as-prepared model dressings were tested as biomedical materials with bactericidal properties towards S. aureus and E. coli strains. The advantages of the NPs prepared in air over their counterparts generated in water found in this work are discussed.

We present a new approach to retrieve Aerosol Optical Depth (AOD) from Moderate Resolution Imaging Spectroradiometer (MODIS) over the turbid coastal water. This approach supplements the operational Dark Target (DT) aerosol retrieval algorithm that currently don’t conduct any AOD retrieval in the regions with large water-leaving radiances in the visible spectrum. Over the global coastal water regions in all cloud-free conditions, this unavailability of AOD retrievals due to the inherent limitation in existing DT algorithm is ~20%. Here, we refine the MODIS DT algorithm by considering that water-leaving radiance at 2.1 μm is negligible regardless of water turbidity. This refinement, with the assumption that the aerosol single scattering properties over coastal turbid water are similar to that over the adjacent open-ocean pixels, yields ~18% more of MODIS-AERONET collocated pairs for six AEROENT stations in the coastal water regions. Furthermore, comparison with these AERONET observations show that the new AOD retrievals are in either equivalent or better accuracy than those retrieved by the MODIS operational algorithm (over coastal land and non-turbid coastal water). Combining the new retrievals with the existing MODIS operational retrievals not only yield an overall improvement of AOD over those coastal water regions, but also successfully extend the spatial and temporal coverage of MODIS AOD retrievals over the coastal regions where 60% of human population resides, and thereby, aerosol impacts on regional air quality and climate are expected to be significant.

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

Turbulence is a fluid dynamic problem refractory to mathematical treatment. Examining a theoretical model of liquid water flowing in a cylinder at different Raleigh numbers, we propose a novel approach to elucidate the first stages of turbulent flows. The weakly bonded molecular assemblies of liquid water form a fluctuating branched polymer in which every micro-cluster displays different density. Against the common view of liquid water as an incompressible and continuous fluid, we suggest that the occurrence of transient local aggregates could be able to generate the vortices and eddies that are the hallmarks of turbulence. We quantify the local changes in velocity, diameter and density required to engender “obstacles” to the average flow. Then, we show how these microstructures, equipped with different Raleigh numbers and characterized by high percolation index, could generate boundary layers that contribute to micro-vortices production. We conclude that the genesis of turbulence cannot be assessed in terms of collective phenomena, rather is sustained, among many other factors, by the underrated microscopic inhomogeneities of fluids like liquid water.

Water treatment efficiency of several filter media such as perlite, modified (silicated) perlite, zeolite and sand were studied on wastewater. This study contains 2 distinct experiments which the first one emphasize on the modified perlite’s performance in removing turbidity which has been gone through 3 phases including low turbidity model water, mid turbidity and high turbidity model water; the second experiment underlines the differentiation between 3 evolutionary material based on perlite which undergoes the filtration process with certain turbid model water. It was dedicated that modified perlite removed more than 90% of turbidity and it functions better than other materials with high turbidity (more than100 NTU). The experiments have been conducted with sodium silicate perlite, normal perlite and synthetic zeolite perlite in order to determine the optimized material which is able to be substituted with perlite in the filtration process.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

An adequate representation of the water infiltration process in the soil allows improving the efficiency in application and the uniformity in surface irrigation. The Green and Ampt model has shown a good representation of the process, and researchers from the United States Department of Agriculture (USDA) determined the values of their parameters for soils of that country, which are shown in tables or through functional relationships and this information is used as reference in several parts of the world, although there is no certainty that they are representative of the soils in Mexico. In this study, the parameters of the Green & Ampt equation were determined and evaluated in some soils of agricultural importance in Mexico. The parameters were obtained in four ways: one of them applied a methodology adapted from Brooks and Corey to quantify the wetting front capillary pressure head and used an permeameter under constant hydraulic head to determine the saturated hydraulic conductivity, and the other three consisted in taking them from three studies reported by the USDA. The values of the parameters suggested in Mexico drastically underestimated the results with relative errors (RE) in a range of -49.0 to -94.0% and the most representative were those obtained with the methodology proposed in this research with RE of -15.0 to 6.0%.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

This literature review was aimed to collect investigations on the in vivo evidences for bacteria associated to fermented dairy foods to behave as probiotics with beneficial effects in the prevention and treatment of various diseases. All main bacterial groups commonly present in high numbers in fermented milks or cheeses were taken into account, namely starter lactic acid bacteria (SLAB) Lactobacillus delbrueckii subsp. bulgaricus and lactis, L. helveticus, Lactococcus lactis, Strepto-coccus thermophilus, non starter LAB (NSLAB) Lacticaseibacillus spp., Lactiplantibacillus plantarum, dairy propionibacteria and other less frequently encountered species. Only studies regarding strains of proven dairy origin were considered. Studies in animal models and clinical studies showed that dairy bacteria ameliorate symptoms of inflammatory bowel disease (IBD), mucositis, metabolic syndrome, aging and oxidative stress, cancer, bone diseases, atopic dermatitis, allergies, infections and damages caused by pollutants, mild stress and depression. Immunomodulation and changes in the intestinal microbiota were the mechanisms most often involved in the observed effects. The results of the studies considered indicated that milk and dairy products are a rich source of beneficial bacteria that should be further exploited to the advantage of human and animal health.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Water deficit (drought) is still one of the most important stress factors affecting not only yields, but also production quality. Breeders are focusing on breeding cultivars and crop lines that are more resistant to water shortages. In addition to breeding, for example, for the size of the roots and changes in the color of the leaves, focus on changing the morphotype i.e. long chaff, multirowed ear. It is predicted that wheat genotypes with a morphotype change should be more drought tolerant. Therefore, our research focused on the study of changes in the physiological parameters of wheat (cv. ´Bohemia´) with a changed morphotype (genotypes ´284-17´ [long chaff] and genotype ´29-17´ [multirowed ear]) in relation to exposure to drought. Pigment content, photosynthesis and transpiration rate, water potential were measured in plants irrigated and affected by water deficit. Water deficit was shown to have a statistically significant effect on transpiration rate, photosynthetic rate, water potential and total chlorophyll content. Furthermore, the influence of the genotype on the observed parameters and on the effect of water deficit was demonstrated. Due to the fact that cv. ´Bohemia´, increases during such periods of transpiration, so for this reason it is not suitable for dry areas. Genotype ́29-17 ́ appears promising with respect to drought resistance.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

As one of the important components of underwater propulsion systems, water lubricated bearings are often failure due to mechanical wearing and vibrating, especially under high loads and prolonged friction. In this paper, a dual-network co-crosslinking strategy based on HNBR is proposed, in which the epoxy network connects with the rubber network through Epoxidized Eommia ulmoides gum. The damping, tribological and mechanical properties of the prepared composite are systematically investigated. The results show that this material has excellent friction and vibration damping properties, with a water-lubricated coefficient of friction as low as 0.022 and a wear resistance as high as 3.87 × 10-6mm3/Nm. Preparing HNBR-based composite by dual network co-crosslinked is proved being a feasible solution to improve the reliability and service life of water-lubricated bearings.

Nanofibres have gained increasing attention due to their advantages of having a high porous structure, narrow pore size and distribution, and a high specific surface area. One of the most efficient techniques for producing nanofibres is via electrospinning. Nanofibres are currently being used in various fields, including water filtration. Although nanofibres possess the ability to filter various components, the fibres generally have a low mechanical strength that can mitigate the performance over time. Therefore, in overcoming this issue, several studies have focused on improving the strength of the nanofibre membranes for a water filtration application. This review discusses the advantages and challenges of nanofibres for water filtration membranes and summarises the methods to increase the strength of the membranes, including solvent vapour, thermal treatment, and chemical crosslinking.

The petroleum industry produces thousands of barrels of oilfield waters from the initial stage driven by primary production mechanisms to the tertiary stage. These produced waters contain measurable amounts of oil in water emulsions, the exact amounts being determined by the chemistry of the crude oil. To meet strict environmental regulations governing the disposal of such produced waters, demulsification to regulatory permissible levels is required. Within the electric double layer theory, coupled with the analytical solutions to the Poisson Boltzmann Equation, continuum electrostatics approaches can be used to describe the static and electrokinetic properties of such emulsion systems. Therefore, theoretical understanding of the stability of oil in water emulsions within such fundamental concepts provides reliable approaches to demulsification. In this paper, we have used theoretical approaches, based on zeta potential and surface charge density models to determine the stability of oil in water emulsions for different crude oil samples. Accordingly, we have used literature based data on the chemistry of the crude oils, and have ranked the order of emulsion stability based on criterial established by zeta potential plots for the oil. Our theoretical calculations show that where the isoelectric points of crude oil samples are closer to each other, the degree of ionization plots versus pH indicate close tends for salinities at varying pH of oilfield waters. Based on the chemistry of crude oil samples, the most efficient and cost-effective means of demulsification is by reducing produced water pH to values closer to the average point of zero charge pH values

In this study, a new approach for estimating volume variations of lakes and reservoirs using water levels from satellite altimetry and surface areas from optical imagery is presented. Both input data sets, namely water level time series and surface area time series, are provided by DGFI-TUM‘s Database of Hydrological Time Series of Inland Waters (DAHITI). The approach is divided into three parts. In the first part, a hypsometry model based on the new modified Strahler approach is computed by combining water levels and surface areas. The hypsometry model describes the dependency between water levels and surface areas of lakes and reservoirs. In the second part, a bathymetry between minimum and maximum surface area is computed. For this purpose, DAHITI land-water masks are stacked using water levels derived from the hypsometry model. Finally, water levels and surface areas are intersected with the bathymetry to estimate a time series of volume variations in relation to the minimum observed surface area. The results are validated with volume time series derived from in-situ water levels in combination with bathymetric surveys. In this study, 28 lakes and reservoirs located in Texas are investigated. The absolute volumes of the investigated lakes and reservoirs vary between 0.099 km³ and 6.448 km³. The correlation coefficients of the resulting volume variation time series with validation data vary between 0.80 and 0.99. Overall, the relative errors with respect to volume variations vary between 2.8% and 14.9% with an average of 8.3% for all 28 investigated lakes and reservoirs. When comparing the resulting RMSE with absolute volumes, the absolute errors vary between 1.5% and 6.4% with an average of 3.1%. This study shows that volume variations can be calculated with a high accuracy which depends essentially on the quality of the used water levels and surface areas. In addition, this study provides a hypsometry model, high-resolution bathymetry and water level time series derived from surface areas based on the hypsometry model. All data sets are publicly available on the Database of Hydrological Time Series of Inland Waters (DAHITI, https://dahiti.dgfi.tum.de).

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

In order to achieve better knowledge of the thermal barrier coatings (TBCs) by supersonic atmospheric plasma spraying (SAPS) process, an experimental study was carried out to elaborate physicochemical properties of particles in-flight during the SAPS process. One type of commercially available agglomerated and sintered yttria-stabilized-zirconia (YSZ) powders were injected into the SAPS plasma jet and collected by shock chilling method. The YSZ particles in-flight physicochemical properties of the melting state, morphology, microstructure, particle size distribution, element composition changes and phase transformation during the SAPS process have been systematically analyzed. The melting state, morphology and microstructure of the collected particles were determined by scanning electron microscopy (SEM). The particle size distribution was measured by a laser particle size analyzer (LPSA). Element compositions were quantitatively analysed by an electron probe X-ray microanalyzer (EPMA). Additionally, the X-ray diffraction (XRD) method was used to analyse the phase transformation. The results showed that the original YSZ powders injected into the SAPS plasma jet were quickly heated and melted from the outer layer companied with breakup and collision-coalescence. The outer layer of the collected particles containing roughly hexagonal shaped grains exhibited a surface texture with high sphericity and the inside was dense with hollow structure. The median particle size was decreased from 45.65 μm to 42.04 μm. Besides, phase transformation took place and the content of zirconium (Zr) and yttrium (Y) element was decreased with the evaporation of ZrO2 and Y2O3.

It is shown that structuring at the microlevel is the intrinsic property of water and aqueous solutions. At room conditions water (including "ultrapure" one) and aqueous solutions are dispersed systems in which microcrystals of NaCl, surrounded by a layer of hydrated water (average diameter - 10-15 microns), are "elementary microparticles", which form the basis of the dispersed phase. Possible ways of formation of these microparticles and their evolution in the process of evaporation of unstructured part of water - dispersion medium - are considered. It is shown, in particular, that they are present in the air as aerosol contaminants. When the ionic strength of the solution increases, the water-salt particles coagulate, forming a new phase - coacervates, remaining on the substrate after evaporation of the liquid part of the water. The aggregates of coacervate structures, formed in a liquid medium, are disordered during heating, which can cause a change in a number of physicochemical properties of water at the temperatures of 50°-60°C range that have not been correctly explained in the framework of atomic-molecular concepts.

Laser in situ keratomileusis (LASIK) is the gold standard in the surgical correction of refractive errors on the cornea. It entails the creation of a superficial hinged corneal flap by a femtosecond laser, ablation of the underlying stromal bed by an excimer laser, and reposition of the flap. The corneal flap can be build in a 2-dimension (2D) fashion with tapered edges, or in a 3-dimension (3D) fashion, with angled sidecut. The latter reduces the risk of flap dislocation and infiltration of epithelial cells. This retrospective study compares with optical coherence tomography 3D and 2D flaps, and respective intra- and early post-operative complications. Four hundred consecutive eyes were included, 200 for each group. In the 3D group, the mean edge angle was 92°. The procedure was in average 5.2 seconds slower in the 3D group (p=0). Non visually significant flap folds were found in 13 eyes of the 2D group and in 7 eyes of the 3D group (p= 0.17). An intracorneal opaque bubble layer induced by laser photodisruption was more commonly observed in the 3D group (9 eyes vs. 2; p=0.03). In conclusion, the creation of a LASIK flap by a 3D-femtosecond laser cut was safe and effective.

Starch is a biopolymer with wide potential for the generation of new biodegradable packages due to its high availability and low price. However, due to its weak functional properties, it is necessary to limit the interaction of some hydroxyl, and to evaluate blends with other polymers to improve their performance. Glycerol plasticized acetylated corn starch films were developed by the casting method, and the impact of incorporating chitosan (TPS:CH) at various proportions (75:25, 50:50, and 25:75 v/v) was studied. The effect of the chitosan ratios on the films' physical, mechanical, water vapor barrier, and thermal properties was evaluated. Chitosan protonated amino groups promote the formation of intermolecular bonds, improving the tensile strength, the thermal stability, the water adsorption capacity, and the gas barrier of starch films. Where the film composed of TPS25-CH75 was the one that presented the best barrier to water vapor. These composite films are a good option for development of biodegradable packaging.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

Morphological parameters like cotton height, branches, Leaf Area Index and biomass are mainly affected by the vegetation water content (VWC). Periodical assessment of the VWC and crop parameters is required for timely management of the crop for maximizing yield. The study aimed at using both optical and microwave remotely sensed data to assess cotton crop condition based on the above mentioned traits. Vegetation indices (VI) derived from ground based measurements (5 narrow band and 2 broad band VIs) as well as satellite derived reflectance (2 broad band VIs) were assessed. Regression models were derived for estimating LAI, biomass and plant water content using the ground based indices and applied to the satellite derived spectral index (from LISS-III) map to estimate the respective parameters. HH and HV polarization from RISAT-1 were used to derive Radar Vegetation Index (RVI). The coefficient of determination of the model for estimating LAI, biomass and vegetation water content of cotton with optical vegetation index as input parameter were found to be 0.42, 0.51 and 0.52, respectively. The correlation between RVI and plant height, date of planting in terms of the age of the crop and vegetation water content were found to range between 0.4 to 0.6. The fresh biomass from RVI showed spatial variability from 100 gm-2 to 4000 gm-2 while the dry biomass map derived from NDVI showed spatial variability of 50 to 950 g m-2 for the study area. Plant water content in the district varied from 65 to 85%. The correlation between optical vegetation index and RVI was not significant. Hence a multiple linear regression model using both optical index (NDVI and LSWI) and SAR index (RVI) was developed to assess the LAI, biomass and plant water content. The model showed a R2 of 0.5 for LAI estimation but not significant for biomass and water content. This study show cased the use of combined optical and microwave (C band) remote sensing for cotton condition assessment.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Communities in semi-arid lands use sand dams to enhance access water during the dry seasons. However, there is limited information on the quality of water derived from these sand dams, especially in degraded lands where storm surface runoff poses contamination risk. Thus, this study aimed at assessing the spatial-temporal variations in water quality of sand dams in Chepareria, West Pokot County in Kenya. Water samples were collected from scooping holes across18 purposefully selected sand dams. Results obtained showed significant differences in water quality based on sand-dams age and location of scooping holes, but the magnitude of these differences differed with specific properties. For instance, in recently constructed sand dams (< 1 year), scooping holes near the sand dam wall had lower pH values (8.5) than holes scooped a distance from the sand dam wall (9.2). For total dissolved solutes and microbial properties, sand dam age had the greatest impact than the location of scooping holes. For example, water obtained from < 1 year old sand dams had significantly higher TDS with an average value of 100.3 mg L-1. The thermotolerant coliforms (TTC) exceeded the maximum allowable levels recommended by World Health Organization. Thus, water obtained from these sand dams should be treated before consumption. Finally, sand dams meant for domestic water harvesting should be protected. Shallow wells with appropriate aprons for effective protection against contamination should be installed to enhance abstraction of safe water from sand dams.

Energy demand has exponentially increased with the increase in the world population and ur-banization. Renewable energy is clean, renewable, and environmentally friendly. Hydrogen production through Proton Exchange Membrane (PEM) electrolyzer is an efficient way to produce renewable energy. The efficiency and energy consumption of the PEM electrolyzer depends on the feed water quality. In this report, we study the effect of pH, TDS, and conductivity on hydrogen production as well as energy consumption during the process. pH values (3, 7, 9), TDS values (300ppm, 600ppm, 900ppm), and conductivity values (30mS/cm, 70mS/cm, 100mS/cm) were studied to understand and optimize the hydrogen production using PEM electrolyzer. The in-vestigations showed that hydrogen production is significantly affected by pH, total dissolved solids, and conductivity, and the best levels of each variable were identified by extensive testing. The findings show both the scientific significance of proton exchange electrolysis in meeting the growing energy demands of society as well as the importance of knowing the influence that di-verse conditions have on the creation of hydrogen. Our research, in general, contributes to the expanding body of scientific knowledge on the topic of the effective production of hydrogen and offers useful insights for the continuation of investigation in this field.

Development of the self-cleaning and anti-fogging superhydrophobic coating for aluminum surfaces which is durable in the aggressive conditions has raised tremendous interest in materials science. In this work, by employing chemical etching technique with mixture of hydrochloric and nitric acid, followed by passivation with lauric acid, superhydrophobic aluminum surface was synthesized. The surface morphology analysis reveals the presence of rough microstructures on coated aluminium surface. Superhydrophobicity with water contact angle of 170 ± 3.9° and sliding angle of 4 ± 0.5° is achieved. Surface bounces off the high speed water jet, indicating excellent water-repellent nature of coating. It is also continuously floated on water surface for several weeks, showing excellent buoyancy nature. Additionally, coating maintains its superhydrophobicity after undergoing 100 cycles of adhesive tape peeling test. Its superhydrophobic nature withstands 90° and 180° bending, and repeated folding and de-folding. Coating exhibits the excellent self-cleaning property. In low temperature condensation test, almost no accumulation of water drops on the surface, showing the excellent anti-fogging property of coating. This approach can be applied to any size and shape of aluminium surface and hence has great industrial applications.

This study investigated the physical properties of section-restoration mortar with calcium nitrite and carbon dioxide (CO2) nanobubble mixing water to develop materials and methods for the repair and reinforcement of cracks in reinforced concrete (RC) structures. As the calcium nitrite content increased, the generation rate and generated amount of nitrite-based hydration products increased, owing to the rapid reaction between NO2- ions in calcium nitrite and C3A(Al2O3). Further, the reaction with C3S and C2S was accelerated, thereby increasing the generation rates of Ca(OH)2 and C-S-H. Further, the large amount of Ca2+ ions in these hydration products reacted with CO32- ions in CO2 nanobubble water, thereby increasing the generation of calcite-based CaCO3 in the cement matrix. This appears to have affected the strength development and durability improvement via the densification of the structure. These results suggest that the performance of polymer cement mortar for repairing concrete structures can be improved if calcium nitrite and CO2 nanobubble water are properly combined and applied.

This work focuses on the study of the microstructure, hardening and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases were originated from reactions between the matrix and boron particles added in the starting mixtures of the composites. Not only was the composite composition studied as an influencing factor in the behaviour of the composites, but also different operational temperatures. Three volume percentages of boron content were tested (0.9, 2.5 and 5 vol % of amorphous boron). The manufacturing process used to produce the composites was inductive hot pressing, which operational temperatures were between 1000 °C to 1300 °C. Specimens showed optimal densification. Moreover, microstructural study revealed the formation of TiB in various shapes and proportions. Mechanical testing confirmed that the secondary phases had a positive influence on the properties of the composites. In general, adding boron particles increased the hardness and stiffness of the composites; however rising temperatures resulted in greater increases in stiffness than in hardness.

Ensuring access to water, sanitation, and hygiene (WASH) facilities, coupled with behavior change education in schools, is fundamental for fostering a conducive learning environment and promoting principles of inclusion, dignity, and equality. This study focuses on 12 primary schools in Anápolis, Brazil, encompassing 4,394 students and 248 teachers. WASH assessments were conducted through a questionnaire, observation of water and sanitation facilities and structures, and microbiological analysis. Over the period 2018 to 2020, the proportion of schools with safely managed drinking water surged from 42% to 92%. However, sanitation conditions in the schools were categorized as a basic level, with hygiene services rated as limited in 92% of the schools due to the absence of soap. While this study reveals that Anápolis schools generally align with WASH guidelines for basic/advanced drinking water services, there is a crucial need for enhancements in both hardware and software facilities to address sanitation and hygiene challenges.

Wild-type p53 cancer therapy-induced senescent cells frequently engulf and degrade neighboring ones inside a massive vacuole in their cytoplasm. After clearance of the internalized cell, the vacuole persists, seemingly empty, for several hours. Despite large vacuoles being associated with cell death, this process is known to confer a survival advantage to cancer engulfing cells, leading to therapy resistance and tumor relapse. Previous attempts to resolve the vacuolar structure and visualize their content using dyes were unsatisfying for lack of known targets and ineffective dye penetration and/or retain. Here, we overcame this problem by applying optical diffraction tomography and Raman spectroscopy to MCF7 doxorubicin-induced engulfing cells. We demonstrated a real ability of cell tomography and Raman to phenotype complex microstructures, such as cell-in-cells and vacuoles, and detect chemical species in extremely low concentrations within live cells in a completely label-free fashion. We show that vacuoles had a density indistinguishable to the medium, but were not empty, instead contained diluted cell-derived macromolecules, and we could discern vacuoles from medium and cells using their Raman fingerprint. Our approach is useful for the non-invasive investigation of senescent engulfing (and other peculiar) cells in unperturbed conditions, crucial for a better understanding of complex biological processes.

This study evaluated the grain size and high organic content from drinking water treatment sludge (DWTS) in the properties of ceramics. Samples were studied using raw and oven dried DWTS at 110 °C in two granulometries (0.180 mm and 0.075 mm), with and without calcination (550 °C), as partial replacement of two soils commonly used in ceramic production. Specimens were prepared with 5, 10, and 20% DWTS and calcined at 950 °C to determine their chemical, physical, mineralogical and mechanical properties. The DWTS reduced the density and increased the absorption and shrinkage of the specimens after calcination. An increase in strength with up to 10% sludge, driven by the presence of fluxing agents, was verified. The processing method had little influence on the properties of ceramic with above 10% of sludge. In conclusion, the use of raw DWTS obtained better results with low energy usage for its reuse.

This study was aimed at investigating the effects of roasting and cryogenic milling on particle size, water solubility, and amount of bioactive components in ginseng root. Samples were pulverized by cryogenic milling, and one treatment condition was selected for each size range (10-50 μm, and >50 μm). The selected samples were roasted at different temperatures (160-200 °C) followed by cryogenic milling. Powdered samples were analyzed for their physicochemical characteristics. Results revealed that roasted samples exhibited significantly smaller particle size than controls (not roasted, p<0.05), and the particle size of roasted samples decreased with increase in roasting temperature until flocculation occurred around 180-190 °C. With decrease in particle size of ginseng; water solubility index, antioxidant activity, total polyphenol content, and total polysaccharide content were observed to increase. Ginseng samples showed an increasing trend in antioxidant activity with decreasing particle size (p>0.05) with significantly higher values for all roasted samples compared to the controls (p<0.05). Non-polar ginsenosides such as Rg2(S), Rg2(R), Rg3(S), Rg3(R), and Rh1(S) showed an increase in temperature-dependent manner. This study revealed that roasting at certain temperature range with cryogenic milling has positive effects on ginseng by reducing its particle size, and increasing water solubility and bioactive components.

NMR Spectroscopy is used, in the temperature range 180-350K, to study local order and transport in liquid water (pure and confined) and its solutions with glicerol and methanol at different molar fractions. Being the liquid water thermodynamic dominated by polymorphism (two coexisting liquid phases: high- and low-density HDL and LDL) - with the LDL due to the hydrophilic HB interactions, originating in the supercooled regime the tetrahedral networking and the liquid-liquid transition – we focused our interest to hydrophobic effects (HE) on these. Nowadays, if compared to the hydrophilicity, little is known about hydrophobicity so that the main purpose of this study is to gain new information on it. We measured the relaxation times (T1 and T2) and the self-diffusion (DS). From the times we took advantage of the NMR property to follow the behaviors of each molecular component (the hydrophilic and hydrophobic groups) separately; they are studied directly and DS in terms of the Adam-Gibbs model: obtaining the configurational entropy (Sconf ) and the specific heat contributions (CP,conf ). Due to the HE all the studied quantities, behave differently. For water-glycerol the HB interaction is dominant for all the conditions, whereas for water-methanol are observable two different T-regions above and below 265 K, dominated respectively by the hydrophilicity and hydrophobicity. A situation linked to the water polymorphism. Below this temperature, where the LDL phase and the HB networking develops and grows, the times and CP,conf change behaviors leading to maxima and minima. Above it, where the HB becomes weak and less stable and the HDL dominates, the hydrophobicity determines the solution properties.

Analysis of water resources of this area was carried out in order to assessing the water quality by determining the concentrations of Cations, Anions, Heavy metals, Trace elements, PH, Alkalinity, Total Dissolved Solids and microbial loads in water samples. Ten (10) water samples were collected from the study area - samples each of rain water, two pond waters - 1 and 2, stream water, four (4) hand-dug wells, hand pump water and a motorized borehole. The results obtained were compared with WHO standards and it showed that all the cations in water samples are within the limits. The water samples at locations B, E, F, G, H, I, and J have high alkalinity and HC0^-₃ content. The heavy metals (Pb, Ni and Cd) and trace elements (Fe and Cu) are dominantly high in the surface waters. Microbiological substances in the water samples from the study area revealed indicator organisms higher than the WHO standard for drinking water. Samples obtained from location G, I and J recorded an absence of E. coli and are fit for human consumptions but needed to be treated due to high MPN (Most Probable Number) index of viable microorganisms as against WHO standard. This research showed that the water resources of the study area are gradually polluted and in the near future may not be good for drinking.

Biomimetic foods are expected to have potential health benefits for the management and prevention of chronic diseases, such as diabetes and cardiovascular disease. In the current research, two commercially available and affordable plant proteins (soy protein isolate-SPI and pea protein isolate-PPI) at two levels (5%, 10%) were added to the Yangyu jiaotuan with an objective to develop a product with reduced glycemic properties and high protein content while maintaining its original taste and texture. The results showed that several important textural properties such as hardness and chewiness did not change significantly during the refrigerated storage. The storage modulus G′ increased with refrigerated storage time for different samples, there were significant differences among the five samples (with and without protein addition) with respect to frequency dependence during rheological measurements. The in vitro starch digestion experiments showed that the starch hydrolysis of Yangyu jiaotuan decreased considerably with the increase in PPI content and during refrigerated storage due to starch retrogradation. Protein has protected the microstructure and there was less damage when compared to samples without protein. The bimodal peaks of the particle size distribution curves showed that the newly developed Yangyu jiaotuan contains two different sizes of particles, the smaller particles (~30 μm) corresponded to PPI and starch granules, while the larger particles corresponded to the fragments of gel network of the starch matrix. Based on the above results, Yangyu jiaotuan mixed with pea protein is a convenient potato staple food product, which complies with the biomimetic potato food very well.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

The effects of acidic electrolyzed water (AEW) on the microbiological and physicochemical properties of fresh-cut red cabbages were studied. The fresh-cut red cabbages and artificially inoculated red cabbages with Salmonella Typhimurium DT104 were washed with distilled water (DW) and different available chlorine concentration (ACC) of AEW for different times. AEW treatments significantly reduced the populations of native aerobic bacteria, molds and yeasts, and artificially inoculated S. Typhimurium DT104 compared to the DW treated and untreated red cabbage samples. The effectiveness of AEW treatments was greatly enhanced with increasing ACC and treatment times. S. Typhimurium DT104 were not detected in the washing water after the red cabbages treated by AEW. The surface color, pH, and total phenolic contents were did not significantly change when the red cabbages were washed with DW and 100 ppm AEW for 3 min. The anthocyanin contents and antioxidant activities of red cabbage were significantly reduced by 18.5% for cyanidin, 22.1% for pelargonidin, and 11.2% for DPPH radical scavenging activity, the impacts on the nutritional benefits of red cabbage were considered as limited and acceptable. The optimal process condition of AEW for washing red cabbage was 100 ppm for 3 min. In these conditions, most of the native microflora were inactivated, and artificial inoculated S. Typhimurium DT104 on the red cabbage were reduced by 40.2% (3.67 log CFU/g) and with minimal losses of nutrients and antioxidant activity, as well as no requirement of discontinuation treatment on the washing water.

The presence of bubbles near the sea surface under certain conditions leads to abnormal sound scattering and a significant change in the acoustic properties of the upper layer of the sea. The article presents some results of sound scattering studies under various sea conditions, up to stormy conditions, when extensive bubble clouds arise. By the method of unsteady acoustic spectroscopy, data on the size distribution of bubbles at various depths have been obtained, which can be described by a power function with exponential decay at small bubble sizes of the order of 10 microns. Estimates of the gas content in bubble clouds and their influence on the acoustic characteristics of the upper layer of the sea have been carried out. It is shown that at sufficiently high concentrations, sharp increases in absorption and dispersion of the sound velocity are observed. Modeling of sound propagation in the presence of a quasi-homogeneous bubble layer shows that it leads both to a change in the laws of the average decay of the sound field along the sound propagation path and to a change in the shallow spatial structure of the field.

Lymphoma is the most prevalent type of cancer in cats, and the search for alternative treatments is of utmost importance given the significant number of animals that exhibit tumor recurrence or are unresponsive to conventional chemotherapy treatment. Oncolytic viruses possess a unique ability to target and eliminate cancer cells while simultaneously stimulating an immune response against these malignant cells. The present study aimed to explore the oncolytic potential of Newcastle Disease Virus expressing green fluorescent protein (NDV-GFP) in a feline leukemia virus (FeLV)-positive lymphoma cell line. Our research suggests that NDV-GFP has a propensity to selectively target, infiltrate, and replicate with-in feline lymphoma cells, resulting in the induction of apoptosis in these cells, as opposed to non-tumor cells. Therefore, our research provides evidence supporting the development of novel oncolytic therapies based on NDV for the treatment of feline lymphomas.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Survivors of severe brain injury may require care in a neurointensive care unit (neuro-ICU), where the brain is vulnerable to secondary brain injury. Thus, there is a need for noninvasive, bedside, continuous cerebral blood flow monitoring approaches in the neuro-ICU. Our goal is to address this need through combined measurements of EEG and functional optical spectroscopy (EEG-Optical) instrumentation and analysis to provide a complementary fusion of data about brain activity and function. The present case demonstrates in a patient with traumatic brain injury, noninvasive cerebral blood flow transients can be recorded that correlate with gold-standard invasive measurements and with the frequency content changes in the EEG data during clinical care.

In the recent years, Cannabis and hemp-based products have become increasingly popular for various applications ranging from recreational use, edibles, beverages to health care products and medicines. The rapid detection and differentiation of phytocannabinoids is, therefore, essential to assess the potency, therapeutic and nutritional values of cannabis cultivars. Here, we implemented the SpiderMass technology for the in vivo detection of cannabidiol acid (CBDA) and tetrahydrocannabinol acid (THCA) and other endogenous organic plant compounds to access distribution gradients within the plants and differentiate cultivars. The SpiderMass system is composed of an IR- laser handheld microsampling probe connected to the mass spectrometer through a transfer tube. The analysis was performed in situ on different plant organs from freshly cultivated Cannabis plants in only a few seconds. SpiderMass analysis easily discriminated the two acid phytocannabinoid isomers by MS/MS and the built statistical models differentiated between four Cannabis cultivars. Different abundancies of acid phytocannabinoids were also found along the plant as well as between different cultivars. All together, these results introduce the direct analysis by SpiderMass as a compelling analytical alternative for forensic and hemp industrial analysis.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

This study aims at better understanding the damage and fracture kinetics in flax fibres elements at both the unitary and bundle scales using an experimental setup allowing optical observation at high recording rate in the course of tensile loading. Defects issues from flax unitary fibre extraction are quantitated using polarized light microscopy. Tensile loading is conducted according to a particular setup adapted to fibres of 10 to 20 µm in diameter and 10 mm in length. Optical recording using high speed camera is performed during loading up to the failure at acquisition speed ranging from 108,000 to 270,000 frames per second. Crack initiation in polymer layers of fibre elements, propagation as well as damage mechanisms are captured. The results show different failure scenarios depending on the fibre element nature. In particular, fractured fibres underline either a fully transverse failure propagation or a combination of transverse and longitudinal cracking with different balances. Image recordings with high time resolution down to 3.7 μs suggest unstable system and transverse crack speed higher than 4 m/s and a slower propagation for longitudinal crack deviation.

A copula is a useful tool for constructing bivariate and/or multivariate distributions. In this article, we consider a new modified class of (Farlie-Gumbel-Morgenstern) FGM bivariate copula for constructing several dierent bivariate Kumaraswamy type copulas and discuss their structural properties, including dependence structures. It is established that construction of bivariate distributions by this method allows for greater flexibility in the values of Spearman's correlation coefficient rho,  and Kendall's tau . For illustrative purposes, one representative data set is utilized to exhibit the applicability of these proposed bivariate copula models.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Abstract: Agarose is known to form a homogeneous thermoreversible gel in aqueous medium over a critical polymer concentration. The solid-liquid phase transitions are thermoreversible but depend on the molecular structure of the agarose sample tested. Then, in a first step, the structure was characterised by 1H and 13C NMR in D2O and in DMSO which is a solvent of agarose whatever the temperature. A low yield in methyl substituent on the D-galactose unit was determined. Then, evolution of the 1H NMR spectrum was followed as a function of temperature in increasing and decreasing temperature process from 25 to 80°C. A large thermal hysteresis is obtained and discussed. It helps to interpret rheological behaviour. In fact, NMR signals are related to proton relaxation and especially to proton involved in H-bonds between water and -OH agarose for tightly bound water and agarose/agarose in chain packing. In a second step, water was exchanged against ethanol which is a non solvent of agarose. A stable gel was demonstrated and characterised by rheology to be compared with aqueous behaviour. Bound water playing the role of plasticizer is probably removed and the gel is much stronger (and brittle) in ethanol with a larger thermal stability. It is the first time that such gel is characterised without phase transition when passing from a good-solvent to a non-solvent. This extends the domains of application of agarose.

Since HIV was first identified, and in a relatively short period of time, AIDS has become one of the most devastating infectious diseases of the 21st century. Classical antiretroviral therapies were a major step forward in disease treatment options, significantly improving the survival rates of HIV-infected individuals. Even though these therapies have greatly improved HIV clinical outcomes, antiretrovirals (ARV) feature biopharmaceutic and pharmacokinetic problems such as poor aqueous solubility, short half-life and poor penetration into HIV reservoir sites, which contribute to the sub-optimal efficacy of these regimens. To overcome some of these issues, novel nanotechnology-based strategies for ARV delivery towards HIV viral reservoirs have been proposed. The current review focus on the benefits of using lipid-based nanocarriers for tuning the physicochemical properties of ARVs to overcome biological barriers upon administration. Furthermore, a correlation of these properties and the potential therapeutic outcomes has been established. Biotechnological advancements using lipid nanocarriers for RNA interference delivery for the treatment of HIV infections were also discussed.

Nano-scale organofunctional silanes have been developed, tested and successfully applied to protect stone buildings in Europe against climatic effects since the 1860s. The same nanotechnologies can also be used in pavement engineering to create strong chemical bonds between a stabilising agent and the material substrata. The attachment of the organofunctional silane to a material also makes the surface of the material hydrophobic, reducing future chemical weathering. These properties allow naturally available materials to be used in any pavement layer at a low risk. In the built environment, scientists soon determined that the successful use of an organo-silane depends on the type and condition of the stone to be treated. The same principles apply to the implementation of applicable nanotechnologies in pavement engineering. Understanding the basic chemistry determining the properties of the stabilising agent and the organofunctional modifying agent and the chemical interaction with the primary and secondary minerals of the material are essential for the successful application of these technologies in pavement engineering. This paper explains some basic chemistry which fundamentally influences engineering outputs that can be achieved using New-age (Nano) Modified Emulsions (NME) stabilising agents with naturally available material in all road pavement TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomass such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240°C), molding time (5-30 min), fiber/fine particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials. The density ranged from 1198 to 1507 kg/m3, the flexural modulus from 0.9 to 6.9 GPa and the flexural strength at breaking point from 6.1 to 43.6 MPa. Water absorption (WA) and thickness swelling (TS) respectively ranged from 21% to 240% and from 9% to 208%. Higher mechanical properties were obtained using SCB with fine particles, low moisture content (4-10%), high temperature (≥ 200°C) and pressure (≥ 68 MPa), while water resistance was improved using more severe thermocompression conditions with the highest temperature (240°C) and time (30 min) or a higher moisture content (≥ 12.5%). Correlations were noted between the mechanical properties and density, while the material obtained with only fine particles had the highest mechanical properties and density. Material obtained with a 30 min molding time had the lowest WA and TS due to internal chemical reorganization followed by hemicellulose hydrolysis into water-soluble extractables.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

The study presented hereafter shows a new methodology to reveal traces of polyethylene (the most common microplastic particles, known as a structure of C2H4) in a sample of ocean water by the irradiation of a 50 keV, 1 µA electron beam. This is performed by analyzing the photon (produced by the electrons in water ) fluxes and spectra (i.e. fluxes as a function of photon energy) at different types of contaminated water with an adequate device and in particular looking at the peculiar interactions of electrons/photons with the potential abnormal atomic hydrogen (H), oxygen (O), carbon (C), phosphorus (P) compositions present in the water, as a function of living and not living organic organisms with a PO4 group RNA/DNA strands in a cluster configuration through a volumetric cells grid.

A framework for the review of existing water management systems and their transformation into robust water sharing systems is offered. The framework focuses on the need to develop efficient and equitable ways to manage water scarcity and plan to deal with the tensions scarcity imposes on any community. The framework identifies a way to bring together traditional community-managed systems with those typically used to allocate water to large water users and more commonly found in developed countries. So that use can be kept within sustainable limits while optimizing use, the framework includes mechanisms that enable the reallocation of water as demand and supply conditions change. Non-consumptive uses are recognized and environmental objectives can be delivered efficiently. Compliance with well-established accounting and hydro-logical concepts. Ways to increase the value of existing entitlements, encourage innovation and protect investments are included as options. It is recognized that the governance and legal arrangements necessary to underpin successful implantation are context specific.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

This research evaluated the role and feasibility of the granular nanocellulose particles (GNC) from sugarcane bagasse obtained from enzymatic hydrolysis in reducing lipid digestibility and permeability in the in vitro simulated gastrointestinal (GI) system. GNC concentration (0.02%, w/v) had significantly affected the released free fatty acid (FFA) reduction of approximately 20%. The Pick-ring emulsion of the GNC and olive oil simulation mixture revealed higher oil droplet size distribution and stability in the initial stage than the vortexed mixture formation. The difference in particle size distribution and zeta potential of the ingested GNC suspension and GNC-olive oil emulsion were displayed during the in vitro gastrointestinal simulation. GNC particles interacted and distributed surrounding the oil droplet leading to the interfacial emulsion. The GNC concentration (0.01-0.10%, w/v) showed low toxicity on the HIEC-6 cell, ranging from 80.0 to 99% of cell viability. The release of FFA containing the ingested GNC suspension and GNC-olive oil emulsion was about 30% reduction compared to without GNC digest solution. The FFA and triglyceride permeability through the HIEC-6 intestinal epithelium monolayer were deceased in the digesta containing the ingested GNC and emulsion. This work indicated that GNC represented a significantly critical role and properties in the GI tract and reduced lipid digestion and absorption. This GNC could be utilized as an alternative food additive or supplement in fatty food for weight control due to their inhibiting lipid digestibility and assimilation.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

The objective of this study was to investigate successional changes in water flow as a result of changes in soil hydraulic properties after crop abandonment under drought and non-drought conditions, and under water uptake by co-occurring perennial plant species to clarify the observation that typical perennial grass species are seldom observed in abandoned fields. Soil hydraulic properties were measured in croplands which had been abandoned for different periods (2, 9, and 18 years from abandonment) and in a grazed grassland site. Hydrological processes in the soil profiles were simulated with soil hydraulic properties under drought and non-drought summer conditions with water uptake from perennial grass species Suction in the surface soils increased with the period of abandonment, with this trend being particularly obvious in a drought year. Available water appears to be restricted in the later successional stage of abandoned fields and in grazed grassland for plants that have drought tolerance. Dry soil and climate conditions are important factors determining the intrusion of the typical perennial grass, S. krylovii, into degraded abandoned fields. This abiotic interaction between soil hydraulic properties and climate conditions may play an important role for plant succession in abandoned cropland.

The presented results of simulations take into account the optical parameters of the selected sea region (from literature data on the southern Baltic Sea) and two optically extreme types of crude oil (from historical data) which exist in the form of a highly diluted oil-in-water emulsion (10 ppm). The spectral index was analyzed based on the results of modelling the radiance reflectance distribution for almost an entire hemisphere of the sky (zenith angle from 0 to 80o). The spectral index was selected and is universal for all optically different types of oil (wavelengths 650 and 412 nm). The possibility of detecting pollution in the conditions of the wavy sea surface (as a result of wind of up to 10 m/s) was studied. It has been also shown that if the viewing direction is close to a direction perpendicular to the sea surface, observations aimed at determining the spectral index are less effective than observation under the zenith angle of incidence of sunlight for all azimuths excluding the direction of sunlight specular reflection.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

Through the process of paradigm change (water as a resource towards water as a common), the authors examine, from a theoretic point of view, the water governability proposed by Agenda del Agua Cochabamba (AdA) – Cochabamba Water Agenda – in the Cochabamba Valley (Bolivia), identifying barriers and drivers to the process that could take place. The rise of Evo Morales in Government in 2006 suggested that policy making would somehow take a fundamental turn resulting in more poor environmental-oriented water policies. However, if that was indeed the case, the implementation of these policies remain controversial as strong power asymmetries still exist at a local level that interfere with national policies shaping the political area. The Cochabamba Water Agenda echoes this debate on the political arena and contributes a politically contested water management through a paradigm change envisaging the difficulties through its implementation. The question remains if this “political” solution to paradigm change in water management may reduce water conflicts.

We have developed IrO_x/M-SnO₂ (M = Nb, Ta, and Sb) anode catalysts, IrO_x nanoparticles uniformly dispersed on M-SnO₂ supports with fused-aggregate structures, which make it possible to evolve oxygen efficiently, even with a reduced amount of noble metal (Ir) in proton exchange membrane water electrolysis. Polarization properties of IrO_x/M-SnO₂ catalysts for the oxygen evolution reaction (OER) were examined at 80 °C in both 0.1 M HClO₄ solution (half cell) and a single cell with a Nafion^® membrane (thickness = 50 μm). While all catalysts exhibited similar OER activities in the half cell, the cell potential (E_cell) of the single cell was found to decrease with the increasing apparent conductivities (σ_{app, catalyst}) of these catalysts: an E_cell of 1.61 V (voltage efficiency of 92%) at 1 A cm^-2 was achieved in a single cell by the use of an IrO_x/Sb-SnO₂ anode (highest σ_{app, catalyst}) with a low Ir-metal loading of 0.11 mg_Ir cm^-2 and Pt supported on graphitized carbon black (Pt/GCB) as the cathode, with 0.35 mg_Pt cm⁻². In addition to the reduction of the ohmic loss in the anode catalyst layer, the increased electronic conductivity contributed to decreasing the OER overpotential due to the effective utilization of the IrO_x nanocatalysts on the M-SnO₂ supports, which is an essential factor in improving the performance with low noble metal loadings.

Biomass and biowaste valorisation is of major interest nowadays because of the spirit of circular economy and of the neutral environmental fingerprint global target. In the current project chondroitin sulphate (ChS) was incorporated with the crustaceous’ and shrimp’s byproduct chitosan (Chi) and the fish industry byproduct gelatine (FG) to obtain dense hydrogel membranes. Glycerol (Gly) was utilized to avoid brittleness. The formation of the hydrogel membranes is attributed to secondary interactions between the natural polymers and the plasticizer. The prepared hydrogel membranes were characterized by Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). The surface morphology of the membranes was examined using scanning electron microscopy (SEM). Dynamic mechanical analysis (DMA) and tensile tests were also performed to evaluate the mechanical response of the membranes. The samples were also evaluated for membrane wettability, degradation rate and water vapor transmission rate (WVTR). Finally, in vitro endothelial cell attachment on the membrane were addressed. The overall results of the study indicate that the hydrogel membranes could be appropriate for external application in wound healing applications as dressings.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

Water scarcity is a significant challenge facing Jordan today. It is a challenge in all areas that use water, and it has become certain that water is the critical factor in the population/resources equation. The water resources in Jordan have become limited with the noticeable increase in the population, mostly resulting from forced migrations in neighboring countries because of the wars and until our time. The rising natural population growth rate, along with the massive influx of refugees, has turned into a state of disproportion between the daily consumption of the population and the amount of water available. That Jordan shares most of its surface water resources with neighboring countries has exacerbated the situation. The current use of water already exceeds its renewable supply. Excessive withdrawal from aquifers, which leads to a lowering of the water table and deterioration in water quality, covered the deficit. This paper focuses on assessing the water situation in Jordan, mainly evaluating this problem and the solution being considered, the true basis for a sustainable water solution requires awareness by the population, and several governmental and non-governmental organizations are actively involved in educating residents about water shortages. The most important and 'actionable' elements of comprehensive water solutions are discussed in this paper, and these elements exist, develop extra water supplies, water harvesting, water desalination, proper wastewater reuse in the agricultural sector, and reduce the demand for drinking water. This research provides specific recommendations to address the shortage of water resources in the Kingdom and highlights the importance of water conservation and optimal use.

The growing need for water has pressured society and governments to focus more on preservation, planning and management of this natural resource, in which is fundamental to ecosystems and especially to humans. In this sense, the goal of this study was to analyze the national policy of water resources in Brazil and Italy, figuring out aspects that could promote its improvement, aiming at the preservation of water sources, guaranteeing satisfactory quantity and quality. They were carried out in 2019 by the environmental agencies of both countries, listing the main disciplinary regulations. The results show that although they are countries with different realities, they resemble similarities in managerial aspects of water resources, with legislation addressing qualitative and quantitative aspects of water, with guiding principles, instruments and actions aimed at the defence of this natural resource.

In order to reveal the frost heaving mechanism of void water behind the lining of high-speed railway tunnels in cold regions，the voids were first classified according to the positional relationship between voids and waterproof panels，and then the water supply and discharge conditions of different types of voids were investigated，then the influence of the excretion conditions on the frost heave force was experimentally studied. Based on these conditions，circular wedge-shaped and flying saucer-shaped void freezing models were established to analyze the evolution process of accumulated water frost heave. Then，according to the relative position of the excretion channel and the void，the excretion coefficient was introduced，and the calculation method of the frost heaving force of the voided water was proposed，and the influencing factors and laws of the frost-heave force were revealed. The results are shown as follows: 1) The blockage of the excretion channel will lead to the generation of frost heaving force; 2) The freezing and thawing process of the water within the cavity develops from the thinnest part of the void edge to the thicker part，and the process of frost heave-thaw，water replenishment-re-freeze heave of the water within the cavity leads to greater and greater frost heave force; 3) The frost-heaving force of the water within cavity is controlled by the void height and the position of the excretion channel. The larger the cavity height is or the closer the excretion channel is to the bottom surface of the void，the greater the frost-heave force is.

Retrogressive thaw slumps (RTSs) are becoming more common on the Qinghai-Tibet Plateau as permafrost thaws, but the hydraulic characteristics of these slumps have not been extensively studied. To fill this knowledge gap, we used the ''space-for-time substitution method'' to differentiate three stages of RTSs: original grassland, collapsing, and collapsed. Our study included on-site investigations, measurements, and simulated analyses of soil water characteristics, environmental factors, and hydrological properties. Our findings show that the measurements and simulated analyses of soil water characteristics were highly consistent across RTSs, indicating the accuracy of the V-G model in reproducing soil hydraulic parameters for different stages of RTSs. The original grassland stage had the highest soil water retention and content due to its high SOM content and fine-textured micropores. In contrast, the collapsed stage had higher soil water retention and content compared to the collapsing stage, primarily due to increased proportions of soil micropores, SOM content, and lower bulk density (BD). Freeze-thaw cycles had a significant impact on the soil texture and structure of RTSs, resulting in a decrease in SOM content and an increase in BD. However, the absence of soil structure and compaction led to the subsequent accumulation of organic matter, increasing SOM content. Changes in field capacity (FC), permanent wilting point (PWP), and soil micropore distribution aligned with variations in SOM content and water content.These findings highlight the importance of managing SOM content and water content to mitigate the adverse effects of freeze-thaw cycles on soil structure and stability at different stages of RTSs. Effective management strategies may include incorporating organic matter, reducing soil compaction, and maintaining optimal water content. Further research is needed to determine the most suitable management practices for different soil types and environmental conditions.

Mexico is currently facing important water management challenges. Cities in the country are facing water scarcity and at the same time, they struggle with floods during the raining season. The water sensitive urban design (WSUD) approach has proved to be helpful in tackling urban water challenges such as floods and water scarcity and it is being implemented in cities around the world. The WSUD approach highlights the role of both the water cycle and the water utilities systems, when transitioning towards a water sensitive stage. Therefore, the objective of this research is to analyse the current situation of the water cycle and the water utility (SIAPA). To do so, we have selected the Metropolitan Area of Guadalajara (MAG) and proposes a case study approach. Within our case of study, we answer two questions: 1) What are the causes of water scarcity and flooding in the MAG? and 2) What are the proposals to solve these problems under a WSUD approach? By answering these questions, we identified that the water management in the MAG corresponds to a single purpose infrastructure. This type of management does not contribute to solve the problems of water scarcity and floods. The water supply policy is based only on the construction of large dams disregarding the storage and use of rainwater, and reuse of greywater, and water-conservation devices. In order to transition towards a water sensitive stage, a WSUD approach that includes multi-purpose infrastructure should be considered. Such as green roofs, swales, rainwater gardens, infiltration trenches, etc.

Background Legionella pneumophila is one of the causes of legionellosis. Water environments serve as the natural habitat and the main sources of Legionella pneumophila. Objectives The aims of this study was to understand the differences of Legionella pneumophila serogroups distribution in well water, tap water, ice cubes, hospital and hotel water in East Java-Indonesia. Methods a total of 60 water samples in east java-Indonesia; from well water (n=25), tap water (n=5), ice cubes (n=5), water from the hospital (n=16), and hotel water (n=9) were detected using polymerase chain reaction with mip gene spesific primers and then it was analyzed by phylogenetic tree. Results For the 60 water samples collected in East Java, 12% of the samples (7/60) were positively contaminated by L. pneumophila. In details, there was 8% of the well water samples (2/25), 2% of the tap water samples (1/5), 2% of the ice cubes samples (1/5), 0% of the hospital water samples (0/16) and 33.33% of the hotel water samples (3/9). The phylogenetic tree showed that Legionella pneumophila contaminating well water isolate 1 from Surabaya and tap water isolate from Sidoarjo was closer to L.pneumophila serogroup 2, 4, 6, 8, 10, 12, isolates from Brazil, China, Spain and Australia. L.pneumophila contaminating the ice cubes from Sidoarjo was closer to serogroup 1, 2, 4, 7, 8, 11, 13, 14, while the bacteria contaminating well water isolate 2 from Sidoarjo as well as water in hotel of Surabaya (hotel water isolate 1, 2 and 3) classified into their own group. Conclusion There is a difference in the distribution of L. pneumophila serogroups between well water, tap water, ice cubes, and hotels.

The world will experience an estimated 40% freshwater supply shortage by 2030, converting water scarcity into one of the principal global challenges that modern society face. Urban water-reuse is recognized as a promising and necessary measure to alleviate the growing water stress in many regions. The transformation to widespread application of water-reuse systems requires major changes in the way water is governed, and countries such as Spain already find themselves involved in this process. Through the systematic assessment of the city of Sabadell (Spain), we aim to identify the main barriers, opportunities and transferable lessons that can enhance governance capacity to implement systems for non-potable reuse of treated wastewater in cities. It was found that continuous learning, the availability and quality of information and level of knowledge and strong agents of change are the main capacity-building priorities. On the other hand, awareness, multilevel network potential and implementing capacity are already well-established. It is concluded that in order to undertake a widespread application of water-reuse practices, criteria examining water quality according to its use need to be developed, independently of the water’s origin. The development and implementation of such a legislative frame should be based on the experience of local water-reuse practices and continuous evaluation. Finally, the need for public engagement and adequate pricing mechanisms are emphasized.

Water availability is a major constraint for spring wheat production on the western Loess Plateau of China. The impact of tillage practices on water potential, water potential gradient, water transfer resistance, yield, and water use efficiency (WUEg) of spring wheat was monitored on the western Loess Plateau in 2016 and 2017. Six tillage practices were assessed, including conventional tillage with no straw (T), no-till with straw cover (NTS), no-till with no straw (NT), conventional tillage with straw incorporated (TS), conventional tillage with plastic mulch (TP), and no-till with plastic mulch (NTP). No-till with straw cover, TP, and NTP significantly improved soil water potential and root water potential at the seedling stage and leaf water potential at the seedling, tillering, jointing, and flowering stages, compared to T. These treatments also significantly reduced the soil-leaf water potential gradient at the 0-10 cm soil layer at the seedling stage and at the 30-50 cm soil layer at flowering, compared to T. Thus, NTS, TP, and NTP reduced soil-leaf water transfer resistance and enhanced transpiration. Compared to T, the NTS, TP, and NTP treatments significantly increased biomass yield (BY) by 18, 36, and 40%, respectively, and grain yield (GY) by 28, 22, and 24%, respectively, with corresponding increases in WUEg of 24, 26, and 24%, respectively. These results demonstrate that NTS, TP, and NTP improved GY and WUEg of spring wheat by decreasing the soil-leaf water potential gradient and soil-leaf water transfer resistance and enhancing transpiration, and are suitable tillage practices for sustainable intensification of wheat production in semi-arid areas.

The Cauto River Basin (CRB), the heartland of Cuban agriculture, has been hit hard by drought and water shortage. In response to this pressing issue, this study provides a comprehensive as-sessment of water supply, demand and balance within the Cauto River Basin, considering the baseline and projected socio-economic and climatic conditions by coupling of SWAT and WEAP models. The obtained results reveal that the annual flow in the CRB is projected to slightly de-crease (2.5%) in which the reduction in the rainy season (3.1%) is higher than that in the dry sea-son (1.3%). Total water demand in the baseline scenario is around 1.194 billion m3, dominated by agriculture (96%), with rice crop requiring nearly half. For the future scenario of 2050, the study shows a 16.6% surge in demand to 1.394 billion m3, driven by climate change and agricultural expansion. However, domestic use decreases by 10% due to population reduction. Water deficit in the future is projected to increase by 52% from 172.4 to 262.7 million m3 due to rising water demand and declining water supply. This study shows that integrating a hydrological model into a water allocation model is a promising approach to estimate the water supply, demand and balance, which is a crucial component of water resources management.

Calabar is a city where 65 per cent of people are living in poverty in informal settlements with low and decreasing access to improved water. In the low-income informal areas of the city, residents are being made responsible for securing their own water supply through several coping strategies. This paper explores the decreasing access to water and coping strategies to shortage in Calabar, Nigeria. It analyses two complementary pieces of data: (i) the households’ coping strategies and (ii) satisfaction with improved water services. A mixed method was introduced and data was collected via fieldwork at three settlements in Calabar. A household survey of 360 respondents, 27 in-depth interviews and 2 focus groups were conducted. Findings show that households engaged in different coping strategies to access water, including conservation (changing routine/reusing), purchasing (spent a significant proportion of their income on buying water) and pumping as a coping strategy. The household's tenure, socioeconomic status and water accessibility determines their decision to move if services are not provided. A crucial differentiation exists between a larger population being granted less access to water versus certain individuals receiving access to a greater quantity of water.

The aim were to determine the drinking water preferences of people applied to a family health center. This cross-sectional study was carried out from April 01st to May 31st, 2022. The data were evaluated using the chi-square test and percent ratios with a significant of P < 0.05. The mean age of all 432 respondents was 48.03±15.86. It was determined that those aged 31-45 had drunk more bottled water (p<0.01) and more spring water (p<0.001), that those aged 65 and over more purified water (p<0.001), that women more tap water (p<0.001), that married people had drunk more demijohn and tap water (p<0.001, each one), that divorced/widows had drunk more packaged and purified water (p<0.001, each one), that the illiterate/literate bottled water (p<0.001, per one), that those who had no income/people who lived on the state or municipal assistance only carboy water (p<0.001). This study suggests that the biggest factor that positively affected the drinking water preference was the packaging of the water. However, the drinking rates of mains water and spring water were quite low. Convincing the authorities to make the mains water drinkable is of great importance in terms of overcoming the public's distrust of mains water.

Water resources are under pressure because of human activities. Its management faces the challenge of enhancing long-term water security while minimizing undesirable economic, social, and environmental impacts along with its production chain. Since water and wastewater treatment plants are designed to maintain and conserve freshwater provisioning services, it is paramount to understand how it operates before proposing options for sustainability. At this point, the diagnosis phase claims for methods scientifically-based, systemic, and more objective to provide information for decision-makers towards strategic management of water resources. This work applies the five-sector sustainability model (5SenSu) to assess Brazil's twenty major water and wastewater treatment companies (WWTC) to quantify their sustainability levels that allow ranking procedures and the establishment of benchmarks for improvements. Under comparative basis, results identified the top-three sustainable companies, CORSAN, CASAN, and SANEPAR, which should be considered examples of best practices. Specifically, the following best-ranked companies in each sector within 5SenSu should be used as benchmark patterns for more oriented best practices: SANEAGO, sector 1; AGESISA, sector 2; CORSAN, sector 3; CASAL, sector 4; MA, sector 5. This work contributes to the advancement in modeling sustainability assessment of human-managed systems (applied in WWTCs in this present study) from a systemic and epistemologically rooted approach, avoiding shortcomings and misleading discussions on the sustainability issue. Quantifying sustainability of WWTCS from 5SenSu allows the identification of those sectors/indicators that requires immediate cleaner production practices by decision-makers to improve overall sustainability, besides identifying those companies more aligned with the requirements of UN SDGs.

This research contributes to the detailed discussion about the approach to secure, hygienic water and cleanliness in Uganda and its pastoral regions. The relationship between the sanitation and clean water access with destitution is also discussed. Although this document is not leading towards the policy recommendation but it is an overall idea of how Uganda progressed because of the provisions adopted by the government, local and international organizations, and NGOs, and how the country lacked before these steps taken. Most of the data mentioned is taken from the house surveys of a decade 2002-2013 alongside the qualitative data. Literature review is also considered and is divided in two sections: first included researches related to water accessibility and usage, while the second section included researches related to work done and progress for diarrheal diseases and sanitation. Afterwards, methodologies were discussed where, firstly, trends and then the limitations in access to the basic necessities of life that is clean water and hygiene are mentioned. At last, the implementations and how they affected the rural Ugandans was discussed.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Water plays a crucial role in maintaining plant functionality and drives many ecophysiological processes. The distribution of water resources is in a continuous change due to global warming affecting the productivity of ecosystems around the globe, but there is a lack of non-destructive methods capable of continuous monitoring of plant and leaf water content that would help us in understanding the consequences of the redistribution of water. We studied the utilization of novel small hyperspectral sensors in the 1350-2450 nm spectral range in non-destructive estimation of leaf water content in laboratory and field conditions. We found that the sensors captured up to 96% of the variation in equivalent water thickness (EWT, g/m²) and up to 90% of the variation in relative water content (RWC). These laboratory findings were supported by field measurements, where repeated leaf spectra measurements were in good agreement (R²=0.79) with a time-lagged change of tree xylem diameter. Further tests were done with an indoor plant (Dracaena marginate Lem.) by continuously measuring leaf spectra while drought conditions developed, which revealed detailed diurnal dynamics of leaf water content. We conclude that close-range hyperspectral spectroscopy can provide a novel tool for continuous measurement of leaf water content at the single leaf level and help us to better understand plant responses to varying environmental conditions.

Clausius’ virial theorem set a basis for relating kinetic energy in a body of independent material particles to its potential energy, pointing to their complementary role with respect to the second law of maximum entropy. In action mechanics, expressing the entropy of ideal gases as a capacity factor for sensible heat or enthalpy plus the configurational work to sustain the relative translational, rotational and vibrational action yields algorithms for estimating chemical reaction rates and positions of equilibrium. All properties of state including entropy, work potential as Helmholtz and Gibbs energies and activated transition state reaction rates can be estimated, using easily accessible molecular properties, such as atomic weights, bond lengths, moments of inertia and vibrational frequencies. Understanding how Clausius’ virial theorem balances the internal kinetic energy with field potential energy justifies partitioning between thermal and statistical properties of entropy, yielding a more complete view of the evolutionary nature of the second law of thermodynamics. The ease of performing these operations is illustrated by three important chemical gas phase reactions, the reversible dissociation of the hydrogen molecules, lysis of water to hydrogen and oxygen and the reversible formation of ammonia from nitrogen and hydrogen. Employing the ergal also introduced by Clausius to define the reversible internal work to overcome molecular interactions plus the configurational internal work of negative Gibbs energy as a function of volume or pressure may provide a practical guide for managing risk in industrial processes and climate change at the global scale.

L-17 is a thiadiazine derivative with putative anti-inflammatory, neuroprotective, and antidepressant-like properties. In this study, we applied combined in silico and in vivo electrophysiology techniques to reveal the potential mechanism of action of L-17. PASS 10.4 Professional Extended software suggested that L-17 might have pro-cognitive, antidepressant, and antipsychotic effects. Docking energy assessment with AutoDockVina predicted that the binding affinities of L-17 to the serotonin transporter (SERT) and serotonin receptors 3 and 1A (5-HT3 and 5-HT1A) are compatible to the selective serotonin reuptake inhibitor (SSRI) fluoxetine and selective antagonists of 5-HT3 and 5-HT1A receptors, granisetron and WAY100135, respectively. However, while the binding mechanisms of L-17 to the SERT and 5-HT1A receptor were similar to fluoxetine and WAY100135, its interacting with 5-HT3 receptor might be substantially different from this of granisetron. Acute administration of L-17 led to dose-dependent inhibition of firing activity of 5-HT neurons of the dorsal raphe nucleus. This inhibition was partially reversed by subsequent administration of WAY100135. Based on both in silico and in vivo electrophysiology assessments, we suggest that L-17 is a potent 5-HT reuptake inhibitor and a putative partial agonist of 5-HT1A receptors. As such, L-17 in particular and thiadiazine derivatives, in general, might be a representative of a new class of antidepressant drugs. Since L-17 also possesses neuro- and cardioprotective properties, it can be useful in affective illness developing due to the general medical condition, such as post-stroke and post-myocardial infarction (MI) depression.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

Sachet water (SW) is a major source of drinking water in most Nigerian homes, thus making it a possible conveyance medium for health risks due to contamination rather than for replenishment of the body. This study collected SW from three busy neighborhoods and investigated for the presence of indicator bacteria – Escherichia coli (E. coli), Total Coliform (TC), Total Heterophilic Bacteria (THB), and Staphylococcus – and some physio-chemical parameters – total dissolved solids (TDS), pH, electrical conductivity (EC), and salinity. Multi-variable and exploratory statistical methods were applied to the results to determine correlations between bacterial contamination levels and perceived brand reputation. Bacteriological test with raw SW samples appeared too numerous to count (TNC) and thus required serial dilutions. After seven dilutions, results obtained revealed that SW brands with good reputation had no TC and E. coli and was statistically significant with groupings of other SW brands (χ2 = 12.28; p < 0.05 and χ2 = 37.96; p < 0.05) respectively. Additionally, SW brands with poor reputation had mean values of TC (19.7X10^8 cfu/ml;14X10^8 cfu/ml1.15X10^8 cfu/ml) and E.coli (18.2X10^8 cfu/ml;38.7X10^8 cfu/ml,32.4X10^8 cfu/ml) exceeding threshold value of zero set by the World Health Organization (WHO). Only one sample from poor reputation brand tested positive for Staphylococcus and was not statistically significant (χ2 =5.2191; p = 0.074). Principal Component Analysis (PCA)/ Factor Analysis (FA) revealed that most of the SW had fecal contamination in an alarming magnitude. Therefore, this study suggests that periodic cleaning of distribution lines, location specific treatment, QC and QA measures should be taken to reduce water security risk for SW consumption in the region.

Water pollution in Iraq has been extended disaster edge; this pollution is caused by wastes and sewages into soil and rivers, pollutant water sources influence the outbreak and serious epidemic status among the population.. The aim of this study is to determine the bacteriological quality of drinking water sources and characteristics of water-borne diseases especially diarrheal cases in Darbandikhan city. 166 water samples, collected from the different sources and areas, were tested for the presences of coliform bacteria as an indicator for pathogen contamination. Most probable number index was used for coliform enumeration. 161 diarrheal cases were taken as a sample from the patients were admitted to the general hospital in Darbandikhan district.. The questionnaire form was planned to view characteristics of diarrheal cases and patients were interviewed directly, the data was analyzed by STATA software application. 46% of the diarrheal cases used tap water for drinking. On the other hand, the reminder (54%) used other sources for the same purpose. All the risk factor such as type of water source, sufficiency of the water, duration of water storage and chlorination were associated with diarrhea. Almost half of the cases were children and three quarters were single. The data was analyzed by STATA version 13.1.This study indicated that the majority of drinking water sources in Darbandikhan city are not suitable for drinking, although net pipe system supplied chlorine significantly it has been proven that the tap water from the homes is not suitable for consumption.

Shanghai is experiencing water supply problems caused by heavy pollution of its raw water supply, deficiencies in its treatment processes and water quality deteoriation in the distribution system. However, little attention has been paid these problems of water quality in raw water, water treatment and household drinking water. Based on water quality data we show that the raw water sources of the Huangpu River and the Changjiang (Yangtze River) estuary are polluted by microbes (TBC), eutrophication (TP, TN and NH3-N), heavy metals (Fe, Mn and Hg) and organic contamination (chemical oxygen demand [COD], detergent and volatile phenols [VP]). The average concentrations of these contaminants in the Huangpu River are almost double that of the Changjiang estuary forcing a rapid shift to the Changjiang estuary for raw water. In spite of filtering and treatment, TN, NH3-N, Fe, COD and chlorine maxima of the treated water and drinking water still exceed the Chinese National Standard (GB5749). We determine that the relevant threats from water source to household water in Shanghai are: 1) eutrophication arising from highly concentrated TN, TP, COD and algal density in the raw water; 2) increasing salinity in the river estuary, especially at the Qingcaosha Reservoir (currently the major freshwater source for Shanghai); 3) more than 50% of organic constituents and by-products remain in treated water; 4) bacteria and turbidity increase in the course of water delivery to users. The analysis presents an holistic assessment of the water quality threats to metropolitan Shanghai in relation to the city’s rapid development.

Wind energy powered pumps could be an alternative to conventional fuel powered pumps for water abstraction because they rely on a free energy and they are environmentally friendly. The objective of this study was to assess the potential of wind energy to operate water abstraction systems in Teso sub-region of Uganda for livestock watering Daily mean wind speeds recorded at a height of 10 m for a period of ten years (2005–2015) were collected from Amuria and Soroti Meteorological stations in the study area. Data were analyzed using Weibull distribution to evaluate the annual wind speed frequency distributions and consequently assess their potential for water abstraction. The results indicated that warmer months (January, February and March) have higher mean wind speeds than the cold months (August, September and October). High wind speeds in the dry seasons corresponded to the periods of high water demand. The highest shape parameter (k) of 3.07 was registered in 2009 and scale parameter (c) of 3.78 in 2012. The highest wind power density of 43 W/m² was obtained the year 2012 while the lowest wind power density of 15.47 W/m² was obtained for Soroti district in the year 2009. The maximum power extractable in Amuria in 2012 was 324 W/m² which is potentially enough for water abstraction. Maximum discharges of 1.86 m³/s and 1.52 m³/s were obtained for Amuria and Soroti districts respectively at mean wind speeds of 5 m/s. Therefore, Teso sub region winds have potential for water abstraction and Amuria district better sites for livestock watering using wind energy.

Cleaning wastewater and using it again for secondary purposes is a measure to address water scarcity in urban areas. However, upscaling of recycled water schemes is challenging due to the possible emergence of various barriers. Based on a review of the governance literature we suggest that a set of five governance conditions is necessary for a successful upscaling of recycled water schemes; (1) policy leadership, (2) policy coordination, (3) availability of financial resources, (4) awareness of a problem, and (5) the presence of a public forum. In order to elaborate on the practical relevance of these conditions we studied a recycled water scheme currently being upscaled in Sabadell, Spain. We reviewed policy documents, conducted a set of 21 semi-structured interviews, and attended two policy meetings about the subject. Our results suggest that Sabadell meets the required conditions for upscaling reused water to a certain extent. However, the presence of a public forum is lacking. We discuss the implications of the absence of the venue and procedures for public participation in Sabadell and how it could be strengthened. Following this discussion, we conclude with some lessons for other cities that plan to upscale their recycled water schemes.

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

Background &amp; Aim: Drug sustainability (DS) is a surrogate marker for treatment efficacy. We aimed to compare the DS of two main biologics used to treat moderate-to-severe ulcerative colitis (UC), infliximab (IFX) and vedolizumab (VDZ), in a real-world setting. Methods: We conducted a retrospective cohort study at a tertiary medical center in Israel. We included patients treated between Dec 1st, 2017, and May 1st, 2021, who were followed for up to 300 weeks. DS was defined as corticosteroid, surgical, and hospitalization-free treatment. Results: 217 patients with UC were included. VDZ had a significantly longer median DS of 265.6 weeks compared to IFX's 106.5 weeks (p=0.001) in treatment-naïve patients, even when adjusting for disease severity (HR 0.55 95 CI 0.3-0.98, p=0.042). In treatment-experienced patients, DS was comparable between IFX and VDZ (p=0.593). Conclusion: VDZ showed significantly longer DS in treatment-naïve patients with UC compared to IFX, also when adjusted for disease severity. There was no difference in DS between VDZ and IFX in treatment-experienced patients and patients switching from one drug to another. VDZ may be a suitable first-line treatment for biologic-naïve patients with moderate-to-severe UC.

Background: Cancer has been one of the most critical health problems during the past decades which require serious consideration, especially in developing countries. Methods: 80 parents of the children with different types of cancers were studied via both questionnaire and person-to-person interview after announcing their informed consent. Results: The highest delay in patients' initial referral was due to the following factors: lack of attention or ignoring the first symptoms, delay in referring to the physician, low economic status and even lack of family support for the patient. In addition, visiting several doctors after the initial diagnosis, uncertainty about the first proposed method, and high cost of treatment can be mentioned as the main causes of delays in the start of treatment. Conclusion: Education plays an important role in identifying the signs of cancer. In addition, proper relationship and cooperation between the health system and physicians as well as provision of adequate information to patients could lead to the long-term cooperation of these patients in continuing their treatment.