In quantum field theory (QFT), it is well known that when Feynman diagrams containing loops are evaluated to account for self interactions, probability amplitude comes out to be infinite which is physically not admissible. So, to make the QFT convergent, various renormalization methods are conventionally followed in which an additional (infinite) counter term is postulated which neutralizes the original infinity generated by diagram. The resulting finite values of amplitudes have agreed with experiments with surprising accuracy. However, proponents of renormalization methods acknowledged that this ad-hoc procedure of subtraction of infinity from infinity to reach at a finite value is not at all satisfactory and there is no physical basis for bringing in the counter term. So, it is desirable to establish a method in QFT which does not generate any infinite term (thus not requiring renormalization), but which predicts same results as conventional methods do. In this paper, we describe such a technique taking self interaction quantum electrodynamics diagram representing electron or photon self energy. In our method, no problem of infinity arises and hence renormalization is not necessary. Still, the dependence of calculated probability amplitude on physical variables in our technique comes out to be same as conventional methods. Using similar procedure, we hope, the problem of non-renormalizability of quantum gravity may be solved in future.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

In-cloud ice mass accretion on wind turbines is a common challenge faced by energy companies operating in cold climates. On-shore wind farms in Scandinavia are often located in regions near patches of forest, the heterogeneity length scales of which are often less than the resolution of many numerical weather prediction (NWP) models. The representation of these forests--including the cloud water response to surface roughness and albedo effects related to them--must therefore be parameterized in NWP models used as meteorological input in ice prediction systems, resulting in an uncertainty that is poorly understood and to present date not quantified. The sensitivity of ice accretion forecasts to the subgrid representation of forests is examined in this study. A single column version of the HARMONIE-AROME 3D NWP model is used to determine the sensitivity of the forecast of ice accretion on wind turbines to the subgrid forest fraction. Single column simulations of a variety of icing cases at a location in northern Sweden were examined in order to investigate the impact of vegetation cover on ice accretion in varying levels of solar insulation and wind magnitudes. In mid-winter cases, the wind speed response to surface roughness was the primary driver of the vegetation effect on ice accretion. In early season cases, the cloud water response to surface albedo effects plays a secondary role in the impact of in-cloud ice accretion, with the wind response to surface roughness remaining the primary driver for the surface vegetation impact on icing. Two different surface boundary layer (SBL) forest canopy subgrid parameterizations were tested in this study that feature different methods for calculating near-surface profiles of wind, temperature, and moisture, with the ice mass accretion again following the wind response to surface vegetation between both of these schemes.

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

Many techniques have been and are being made to find alternatives to water-saving practices. Among them, Partial root drying (PRD), one of the effective approaches, plays a major role in reducing the harmful effects of water deficit stress. An experiment was carried out using irrigation strategies [I1 (100% full irrigation “FI”), I2 (75%FI), I3 (50%FI), and I4 (PRD (50%FI)] and soil organic mulch [L0 (Zero layer organic soil mulch” control”), L1 (Single layer organic soil mulch), L2 (Two layers of organic soil mulch), and L3 (Three layers of organic soil mulch)] to inspect the impact of those treatments for increasing yield, water productivity and saving energy under arid region conditions. To meet the study's objective, two field experiments were carried out at a private farm. Our results demonstrated a general decrease in water stress and salt accumulation inside root-zone area with PRD with L3. The PRD strategy increased fruit yields by 3.7 and 7.3% and water productivity by 51.9 and 53.1% compared with I1 during 2020/2021 and 2021/2022, respectively, while reducing the applied irrigation water by 50 %. The PRD strategy showed superior results in increasing mango yield and water productivity. In general, PRD can be used as good technique to save water and energy up to 50% and enhance productivity along with using organic mulching, ultimately improving mango yield under arid climatic regions. It may prove a good adaptation strategy for current and future water shortage scenarios of climate change.

In this paper, particular attention is paid to an advanced variant of the plug-in hybrid engine, known as PHEV, which combines two functionalities: the vehicle's internal combustion engine (ICEV) and the electric engine (BEV). The paper also presents the assumptions of the DEVS model, which allows for the estimation of vehicle’s energy consumption. The study described herein also presents the influence of factors such as ambient temperature and constant speed on the PHEV’s energy consumption. It has been shown that the vehicle’s range estimated based on its electronic control module (ECU) is about 20% shorter per annum on average for its year-round operation in every-day driving conditions. When analyzing the energy consumption based on the vehicle’s unit energy consumption model, attention was paid to values that are strongly correlated with the traffic volume and weather conditions affecting the moving vehicle. In addition, the authors emphasized that the estimated total energy consumption of an electric (BEV) or hybrid (PHEV) vehicle, relative to the normative values arising from the type approval test cycle, deviate from the actual values arising from real driving conditions and often vary substantially. In extreme cases, the actual range of a hybrid vehicle is 75% shorter.

A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

The research introduces the concept of Strong Energy (SE) as a force that encompasses all the different forms of energy in the universe. The study aims to create a mathematical framework that can describe the relationship between these different types of energy and how they can be converted from one form to another. The paper explores the theoretical implications of this model and investigates how it aligns with established physics principles like the conservation of energy and fundamental forces. The paper also discusses potential experiments and the impact this research could have on cosmology, particle physics, and our understanding of energy. This work sets the stage for future research in this area of study.

The article addresses the issue of reducing the carbon footprint in the formula of the European Union’s New Green Deal using nuclear energy introduced in place of coal. It contains an analysis of the possibilities offered by currently developed concepts of using nuclear energy in the context of existing energy infrastructure in Poland. It indicates the compatibility of coal and nuclear technologies for generating electricity and heat, considering only those with the highest level of technological readiness. The aim of the article is to identify the energy transformation in Poland using nuclear technologies and acquiring, creating and developing knowledge on the subject. It is assumed that the future of coal-nuclear transformation depends on determining where investment processes could take place in Poland, demonstrating the power that can be replaced through transformation, and indicating appropriate coal CPP (Carbon Power Plant) and nuclear NPP (Nuclear Power Plant) technologies with which a roadmap for the development of Polish nuclear energy can be created. The direction of potential actions is shown, whose coordination and implementation requires cooperation between many entities with appropriate knowledge and experience. For the purposes of this article, preliminary research was conducted on the possibilities offered by currently developed concepts in the context of existing energy infrastructure in Poland, its transformation, and the necessary social capital and its sources. The considerations did not take into account power plants and combined heat and power plants that have been liquidated or the use of their remaining infrastructure.

This paper results from our investigation into novel means of electromagnetic propulsion. It requires the basis of our claims to be put on a sound theoretical footing regarding the purported momentum exchange with the electromagnetic field. One of these concerns is the huge discrepancy between the energy density of the Zeropoint and its purported manifestation as the Cosmological Constant. Here we state that it is manifestly wrong to introduce the zeropoint at zero order into the stress-energy tensor, because it is something which describes zero particle count. As a fluctuation, it belongs in a higher order Taylor expansion in frequency of the stress-energy tensor. Furthermore in the 3^rd order in the Einstein constant our procedure is some 9 orders of magnitude too small. We make up this difference by suggesting that vacuum energy is much higher still and that more degrees of freedom exist in physics beyond the Standard Model or that there is interaction energy between the modes.

In this work, we explore new constraints on phantom scalar field cosmologies with a scalar field employing early times catalogues related to CMB measurements, along with the local standard observables, like Supernovae Type Ia (SNIa), H(z) measurements (Cosmic Clocks), and Baryon Acoustic Oscillations (BAO) baselines. In particular, we studied a tracker phantom field with hyperbolic polar coordinates that have been proposed in the literature. The main goal is to obtain precise cosmological constraints for H0 and σ8, in comparison to other constructions that present tension in early cosmological parameters. Our results show that phantom scalar field cosmologies have a reduced statistical tension on H0 that it is less than 3σ using model-independent CMB catalogues as SPT-3G+WMAP9 and ACTPol DR-4+WMAP9 baselines. This suggests these models using a different phantom potential might address the Hubble constant problem and reduce the systematics involved.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

Cosmic inflation has presented solutions for a number of important cosmological problems, yet left some unanswered. In this paper, we present a cosmological model based on the quantization of the zero-point field which is consistent with empirical data, requires fewer assumptions, and presents answers to some of those unanswered questions. A comparison between standard cosmology and the theory presented in this paper is given below. Vacuum energy density: Standard inflationary model needs both Hubble’s constant and Matter density to estimate it. But, new cosmological model needs only Hubble’s constant. Non-vacuum energy density: Standard model can’t predict it. But, the new model can predict using only Hubble’s constant. Ratio of vacuum energy to total energy: Standard model can’t predict it. But, new model can predict it, that too without using Hubble’s constant. Energy conservation: In standard model, total energy is not conserved before inflation. But, in the new model, energy is conserved right from beginning of the universe whose net energy (including gravitational potential energy) is always zero. Flatness and homogeneity: Standard model needs Inflaton field with a specific potential energy distribution to explain it. But, new model doesn’t need any such hypothetical field, just the zero-point field is sufficient. Based on the new cosmological model, in the conclusion, realistic possibility for existence of multiverse and a mechanism for end of universe are discussed.

Metabolic flexibility is the ability of an organism to adapt its energy source based on nutrient availability and energy requirements. In humans, this ability has been linked to cardio-metabolic health and healthy aging. Genome-scale metabolic models have been employed to simulate metabolic flexibility by computing the Respiratory Quotient (RQ), which is defined as the ratio of carbon dioxide produced to oxygen consumed, and varies between values of 0.7 for pure fat metabolism and 1.0 for pure carbohydrate metabolism. While the nutritional determinants of metabolic flexibility are known, the role of low energy expenditure and sedentary behavior in the development of metabolic inflexibility is less studied. In this study we present a new description of metabolic flexibility in genome-scale metabolic models which accounts for energy expenditure, and we study the interactions between physical activity and nutrition in a set of patient-derived models of skeletal muscle metabolism in older adults. The simulations show that fuel choice is sensitive to ATP consumption rate in all models tested. The ability to adapt fuel utilization to energy demands is an intrinsic property of the metabolic network

Low energy consumption is a significant contribution of new and retrofitted buildings that place an emphasis on energy efficiency. Although the mandatory requirements of the U-factor and R-value are described in the Vietnamese National Technical Regulation on the energy efficiency of buildings—QCVN09:2017/BXD, these values are not widely publicized, leading to designers facing difficulties when choosing suitable materials at the design stage. This study focuses on the method used to declare the heat transfer values of building materials based on the energy labeling process in order to create an energy labeling program for building materials. To accomplish this objective, criteria and labeling procedures for windows, doors, walls, and building roofs have been developed. In addition, a case study of insulation product labeling was used to evaluate the applicability of the developed labeling program in the implementation phase.

Large office buildings are responsible for a substantial portion of energy consumption in urban districts. However, thorough assessments regarding the Nordic countries are still lacking. In this paper we analyse the largest dataset to date for a Nordic office building, by considering a case study located in Stockholm, Sweden, that is occupied by nearly a thousand employees.Distinguishing the lighting and occupants’ appliances energy use from heating and cooling, we can estimate the impact of occupancy without any schedule data. A standard frequentist analysis is compared with Bayesian inference, and the according regression formulas are listed in tables that are easy to implement into building performance simulations (BPS). Monthly as well as seasonal correlations are addressed, showing the critical importance of occupancy.A simple method, grounded on the power drain measurements aimed at generating boundary conditions for the BPS, is also introduced; it shows how, for this type of data and number of occupants, no more complexities are needed in order to obtain reliable predictions. For an average year, we overestimate the measured cumulative consumption by only 4.7%. The model can be easily generalised to a variety of datasets.

We have performed first-principles calculations to study the interfacial exchange coupling and magnetocrystalline anisotropy (MCA) energy in a SmCo₅/Sm₂Co₁₇ multilayer model systems. The phase of SmCo₅ and Sm₂Co₁₇ stacking along (0001) direction are structurally well matched. The atomic structure, including the alignment and the separation between layers, were firstly optimized. Then the non-collinear magnetic structures were calculated to explore the exchange coupling across the interface and the variation of MCA energy. We found that the inter-phase exchange coupling strength, rotating behavior and MCA energy are strongly dependent on the atomic thickness of the SmCo₅ and Sm₂Co₁₇ phase.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Currently there are strong and sustained growth trends observed in multi-disciplinary industrial technologies such as building-integrated photovoltaics and agrivoltaics, where renewable energy production is featured in building envelopes of varying degrees of transparency. Novel glass products can provide a combination of thermal energy savings and solar energy harvesting, enabled by either patterned-semiconductor thin-film energy converters on glass substrates, or by using luminescent concentrator-type approaches to achieve high transparency. Significant progress has been demonstrated recently in building integrated solar windows featuring visible light transmission of up to 70%, with electric power outputs of up to Pmax ~ 30-33 Wp/m2. Several slightly different designs were tested during 2021-2023 in a greenhouse installation at Murdoch University in Perth, Western Australia. The objective of this paper is to report on the field performance of these PV windows in the context of agrivoltaics, and to provide some detail of the performance differences measured in several solar window designs related to their glazing structure materials. Methods for the identification and quantification of long-term field performance differences and energy generation trends in solar windows of marginally different design types are reported. The paper also aims to outline the practical application potential of these transparent construction materials in built environments, focussing on the measured renewable energy figures and seasonal trends observed during the long-term study.

The textbook analysis of vacuum energy density (VED) in flat spacetime follows from Pauli’s lectures of 1951, in which quantum vacuum is modeled as a reservoir of free harmonic oscillators. In his lectures, Pauli shows that deriving a nearly vanishing VED is contingent upon fulfilling three corollary conditions called polynomial-in-mass-constraints. The goal of this work is to evaluate Pauli’s constraints against the Standard Model parameters and the Higgs mechanism of spontaneous symmetry breaking.

A large share of the reinforced-concrete (RC) building stock in Mediterranean countries faces a dual challenge of seismic vulnerability and energy inefficiency, calling for urgent renovation ef-forts. While energy upgrades have been the focus of previous renovation policies, recent research highlights the critical need for integrated retrofitting solutions that address both structural integ-rity and energy performance. Multi-criteria decision making (MCDM) approaches are a promis-ing tool for optimizing the combined choice of these integrated interventions, considering various decision variables (DVs), of economic, social, environmental, and technical nature. To understand the impact of climate and seismic hazard conditions on multi-criteria based retrofitting assess-ment, a case-study RC school building is selected and assumed to be located in three distinct cli-mate conditions - cold, mild, and warm - and three seismic hazard levels – low, medium and high. Moreover, given the complexity and challenges of quantifying seismic performance metrics for practitioners, an available simplified (practice-oriented) approach is compared herein with a more thorough research-based one for quantifying the seismic performance of RC buildings with-in the MCDM framework. Both approaches are applied to the case-study building, considering twelve possible combinations of energy and seismic interventions. The accuracy of the practice-oriented approach and its impact on the retrofitting rankings is evaluated, emphasizing the im-portance of accessible and efficient evaluation methods in facilitating informed decision-making for building renovation.

Large inconsistencies in the outcome of precise measurements of Newtonian gravitational ‘constant’ were identified throughout more than three hundred experiments conducted up to date. This paper illustrates the dependency of the Newtonian gravitational parameter on the curvature of the background and the associated field strength of vacuum energy. Additionally, the derived interaction field equations show that boundary interactions and spin-spin correlations of vacuum and conventional energy densities contribute to the emergence of mass. Experimental conditions are recommended to achieve consistent outcomes of the parameter precision measurements, which can directly falsify or provide confirmations to the presented field equations.

We explore the field equations in a 4-d complex space-time, in the same way, that general relativity does for our usual 4-d real space-time, forming this way, a new "general relativity" in C⁴ space-time, free of sources. Afterwards, by embedding our usual 4-d real space-time in C⁴ space-time, we describe geometrically the energy-momentum tensor T_μν as the lost geometric information of this embedding. We further give possible explanation of dark eld and dark energy.

Energy keeps the global economy alive, whereas it is extensively exposed to various climate change impacts. In this context, severe business competition (e.g., the building sector) and the unwise use of natural resources and ecosystem services (e.g., fossil fuel energy sources) seem to sharpen the relevant effects of climate change. Indicatively, contemporary issues at the interface of building energy performance and environmental quality levels include consequences from global warming, increasing releases of carbon dioxide to peak electrical loads, power grid and building planning, and energy demand and supply issues. In light of such concerns, the present review paper attempts to disclose the multifaceted and multidisciplinary character of building energy use at the interface of the economy, the environment, and society against climate change. This review highlights energy efficiency concepts, production, distribution, consumption patterns, and relevant technological improvements. Interestingly, the reviewed contributions in relevant literature reveal the need and necessity to alter the energy mix used and relevant energy use issues. These include developments in climate-proof and effective systems regarding climate change impacts and shocks. Practical implications indicate that the sustainable development goals for clean energy and climate action should be followed if we wish to bring a sustainable future closer and faster to our reality.

This paper provides an open dataset of measured energy use, solar energy production, and building air leakage data from a 328 m² (3,531 ft²) all-electric, zero energy commercial building in Virginia, USA. Over two years of energy use data were collected at 1-hour intervals using circuit-level energy monitors. Over six years of solar energy production data were measured at 1-hour intervals by 56 microinverters. The building air leakage data was measured post-construction per ASTM-E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization and the United States Army Corps (USACE) Building Enclosure Testing procedure; both pressurization and depressurization results are provided. The architectural and engineering (AE) documents are provided to aid researchers and practitioners in reliable modelling of building performance. The paper describes the data collection methods, cleaning, and convergence with weather data. This dataset can be employed to predict, benchmark, and calibrate operational outcomes in zero energy commercial buildings.

Control of autonomous robot motion in radial mass density field is presented. In that sense the robot motion is described as the function of the radial mass density parameters. The radial mass density field is between the maximal radial mass density and the minimal radial mass density. Between these two limited values one can use n points (n = 1, 2, . . . nmax) and calculate the related radial mass density for each point. The radial mass density is maximal at the minimal gravitational radius and minimal at the maximal gravitational radius. This conclusion is valid for Planck scale, but also for the scales that are less or higher of that one. Using the ratio of the Planck mass and Planck radius it is generated energy conservation constant with value κ = 0.99993392118. Further, in this theory it is possible to connect Planck’s and gravitational parameters as functions of the maximal (or minimal) radial mass density. In that sense the autonomous robot motion in radial mass density field is important for the control of the robot motion at micro and nano scales.

Although buildings constitute 35% of global energy use and 38% of carbon emissions from energy, the amount of energy and energy-related carbon emissions are increasing rapidly. On the other hand, non-renewable usable energy resources are decreasing on the contrary. New buildings are being built due to the increasing population and the existing building stock not meeting the needs or losing its lifespan. Some of the existing building stock is demolished and renewed for structural reasons and some for reasons such as usage performance. It is possible to reduce both energy consumption and greenhouse gas emissions with strategic energy uses in existing building stocks. There are various techniques to measure the maximum performance of sustainable and energy-efficient use of existing building stocks with which changes. Building Information Modeling (BIM) technology is one of these techniques that provides wide opportunities to users in recent years, and it is almost a virtual laboratory of structures. Building stocks can be modeled with BIM, and alternative shell and system suggestions can be used to measure how building performance has changed and to achieve the best results. In this research study, improvement scenarios that optimize energy use in existing building stocks are investigated on a sample residential building by using the virtual laboratory facilities of BIM. After measuring the current energy performance of the existing building with BIM tools, 192 alternative results were obtained with 6 variables (external walls, roof, insulation layers, transparent surface materials, lighting, and photovoltaic panels). The obtained alternatives were compared with the current state of the existing building. The material expenditures and amortization periods required for these alternative scenarios are also calculated. The results obtained were evaluated according to annual / lifetime energy consumption, fuel, electricity, initial investment costs, energy use intensity, and carbon emission amounts. With the optimization of the current situation of the sample building, annual fuel consumption decreased by 61% and electricity consumption by 64%. The amortization period of the optimum improvement was determined as 12 years.

In the context of the energy transition, the integration of land use considerations into energy planning is increasingly vital, especially in scenarios where land availability is a constraint. This study addresses the challenge of incorporating land-use aspects into Energy System Optimization Models (ESOMs), with a focus on the unique context of Pantelleria Island. It aims to bridge the gap in methodologies for renewable energy potential assessment and model integration, considering the critical role of land pricing and availability. It combines geospatial data aggregation with model adaptation to include detailed land use aspects. Findings highlight the substantial impact of land costs on renewable energy planning, with land pricing significantly altering model outcomes. This research offers key insights for sustainable energy planning and underscores the importance of considering land use in energy transition strategies.

Sport centers are significant energy consumers. This article outlines the engineering design for a comprehensive energy performance upgrade of the indoor sport hall in Arkalochori, Greece, and presents the projected results. The indoor sport hall constitutes a major sport facility in the mainland of Crete, hosting a broad cluster of sport municipal activities and the official basketball games of the local team in the 2nd national category. Having being constructed in the mid ‘90s, the facility exhibits very low thermal performance, with considerably high U-factors for all constructive elements (from 4 to 5 W/m2∙K), still use of diesel oil for indoor space heating and domestic heat water production and ineffective, old lamps and luminaries covering the lighting needs of the facility. The energy performance upgrade of the indoor sport hall was holistically approached, through all possibly applicable passive and active measures: insulation of opaque surfaces and replacement of openings, installation of new stone wool panels, installation of heat pumps for indoor space conditioning, elimination of diesel oil for any final energy use, installation of a solar-combi system for domestic hot water production, upgrade of all indoor and outdoor lighting equipment, installation of solar tubes on the main sport hall roof for natural lighting and installation of a photovoltaic plant on the same roof for the compensation of the remaining electricity consumption. With the proposed measures, the indoor sport hall is upgraded to zero energy facility. The payback period of the investment was calculated at 26 years, on basis of the avoided energy resources procurement cost. This work has been funded by the Horizon 2020 project with the acronym “NESOI” and was awarded with the public award of the “Islands Gamechanger” competition of the NESOI project and the Clean Energy for EU Islands initiative.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

This paper presents performed Ansys numerical simulation on WindFloat structures. It contributes to the methodology of calculation based on CFD instruments to study the movements of the waves on semi-submersible stationary structures and highlights the importance of using RAO functions. RAO numerical approach developed can be applied to design semisubmersible WindFloat structures in order to fulfill essential requirements regarding operational safety and design. Numerical methodology was designed in accordance marine loads and the I.T.T.C. recommendations. The numerical RAO results for regular wave movements include many elements for the semi-submergible structure. Close results to open sea operation can be achieved by constant improvement in numerical simulation methodologies. The work opens the way for further hydrodynamic development on irregular waves for realistic hydrodynamic and structural response of the actual semi-submersibles at sea. The results demonstrate the accuracy of RAO function approach for specific WindFloat in Jonswap spectrum.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

The recent provision of energy-harvesting capabilities to wireless sensor networks has entailed the redefinition of design objectives. Specifically, the traditional goal of maximizing network lifetime has been replaced by optimizing network performance, namely delay and throughput. The present paper contributes to this reformulation by considering the routing problem for the class of time-driven energy-harvesting WSN (EH-WSN) under regular or quasi-periodic energy sources. In particular, this paper shows that the minimum hop count (MHC) criterion maximizes the average duty cycle that can be sustained by nodes in this type of scenarios. This is a primary objective in EH-WSN, since large duty cycles lead to enhanced performance. Based on a previous result, a general expression is first obtained which gives mathematical form to the relationship between duty cycle and traffic load for any node in a time-driven EH-WSN fed by a regular energy source. This expression reveals that the duty cycle achievable by a node decreases as its traffic load increases. Then, it is shown that MHC minimizes the average traffic load over the network, and thus it maximizes the average duty cycle of nodes. This result is numerically validated via simulation by comparison with other well-known routing strategies. Accordingly, this paper suggests assigning top priority to the MHC criterion in the development of routing protocols for time-driven EH-WSN under regular energy sources.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Building more energy efficient and sustainable urban areas that will both mitigate the effect of climate change and adapt for the future climate, requires the development new tools and methods that can help urban planners, architect and communities achieve this goal. In the current study, we designed a workflow that links different methodologies developed separately, to derive the energy consumption of a university school campus for the future. Three different scenarios for typical future years (2039, 2069, 2099) were run as well as a renovation scenario (Minergie-P). We analyse the impact of climate change on the heating and cooling demand of the buildings and determined the relevance of the accounting of the local climate in this particular context. The results from the simulations showed that in the future there will a constant decrease in the heating demand while for the cooling demand there will be a significant increase. It was further demonstrated that when the local climate was taken into account there was an even higher rise in the cooling demand but also that the proposed renovations were not sufficient to design resilient buildings. We then discuss the implication of this work on the simulation of building energy consumption at the neighbourhood scale and the impact of future local climate on energy system design. We finally give a few perspective regarding improved urban design and possible pathways for the future urban areas.

Hybrid renewable energy systems (HRES), complemented by pumped hydropower storage (PHS), have become increasingly popular amidst the increase of renewable energy penetration. This con-figuration is even more prosperous in remote regions that are typically not connected to the mainland power grid, where the energy independence challenge intensifies. This research focuses on the design of such systems, from the perspective of establishing an optimal mix of renewable sources that takes advantage of their complementarities and synergies, combined with the versatility of PHS. However, this design is subject to substantial complexities, due to the multiple objectives and constraints to fulfill, on the one hand, and the inherent uncertainties as well, that span over all underlying processes, i.e., external, and internal. In this vein, we utilize a proposed HRES layout for the Aegean Island of Sifnos, Greece, to develop and evaluate a comprehensive simulation-optimization scheme in deterministic and, eventually, stochastic setting, revealing the design problem under the umbrella of uncertainty. In particular, we account for three major uncertain elements, namely the wind velocity (natural process), the energy demand (anthropogenic process), and the wind-to-power conversion (internal process, expressed in terms of a probabilistic power curve). Emphasis is also given to the decision-making procedure, which requires a thorough interpretation of the uncertainty-aware optimization outcomes. Finally, since the proposed PHS uses the sea as the lower reservoir, additional technical challenges are addressed.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

The purpose of this paper is to find a quantum formulation of entropic gravity, incorporating the bijective theory. In a first part, we will describe the basis of the bijective theory. In a second part, we will incorporate the stress energy quantum tensor defined in the linear approximation of the Einstein’s equation in its quantum version to entropy. In the third part, we will integrate the bijective theory with the newly created relativistic quantum entropy. This will lead us four part where we will formalize quantum entropic gravity.

Digital technology makes energy systems more dynamic, efficient, reliable and sustainable. Promoting the digital governance of renewable energy is not only a key part of energy transformation, but also an important initiative to cope with the global energy crisis, which provides a new impetus for realizing the goal of net-zero emissions. In order to achieve the "dual-carbon" goal, China has been actively promoting energy reform and enhancing the wide application of digital technologies in the development and utilization of renewable energy. The digital governance system and governance capacity of renewable energy is an important support for the modernization of the national governance system and governance capacity. Although the digital governance of renewable energy in China has better policy support and advantages, the dilemmas it faces are still relatively prominent, including unsound laws and policies, insufficient governance capacity, and security loopholes in digital technology, etc. Therefore, this paper proposes a problem-oriented approach to the digital governance of renewable energy. Therefore, this paper puts forward problem-oriented optimization suggestions to innovate the legal system of renewable energy digital governance, promote the digital transformation of China's renewable energy industry, provide development space for renewable energy digital governance in a diversified mode, and enhance the digital governance capacity by improving the renewable energy security system.

Energy and institutional quality are two factors that determine economic output, but these two factors are often neglected in the search for economic output. Therefore, this study examines the relative importance of energy use and its interaction with institutional quality for economic output. We employ a robust econometric estimation technique on a panel sample of 21 African countries between 2002-2019. Our results show that energy use is significant and negatively related to economic output while moderating terms of institutional quality are significantly associated with economic output, but the direction of the association depends on the specific quality. We find the moderating term control of corruption and government effectiveness to be negative and significantly associated with economic output, whilst political stability, regulatory quality, rule of laws, voice, and accountability positively impact. Our results imply that improved economic output is possible when there are specific institutional strategies.

The interest in renewable energy to replace fossil fuel is increasing as the problem caused by climate change become more severe. Small hydropower (SHP) is evaluated as a resource with high development value because of its high energy density compared to other renewable energy sources. SHP may be an attractive and sustainable power generation environmental perspective because of its potential to be found in small rivers and streams. The power generation potential could be estimated based on the discharge in the river basin. Since the river discharge depends on the climate conditions, the hydropower generation potential changes sensitively according to climate variability. Therefore, it is necessary to analyze the SHP potential in consideration of future climate change. In this study, the future prospect of SHP potential is simulated for the period of 2021 to 2100 considering the climate change in three hydropower plants of Deoksong, Hanseok, and Socheon stations, Korea. As the results, SHP potential for the near future (2021 to 2040) shows a tendency to be increased and the highest increase is 23.4% at the Deoksong SPH plant. Through the result of future prospect, we have shown that hydroelectric power generation capacity or SHP potential will be increased in the future. Therefore, we believe that it is necessary to revitalize the development of SHP in order to expand the use of renewable energy. Also, a methodology presented in this study could be used for the future prospect of the small hydropower potential.

As the international community attaches importance to environmental and climate issues, carbon dioxide emissions in various countries have been subject to constraints and limits. Carbon trading market, as a market tool to reduce greenhouse gas emissions, has gone through a development process from a pilot carbon market to a national carbon market in China. At present, the industries included in the national carbon market are mainly the electric power industry, and the carbon emissions of the electric power industry account for about 40% of the national carbon emissions. According to the construction history of foreign carbon markets, China's future carbon quota allocation will gradually transition from free allocation to auction allocation,the auction mechanism will bring a heavy economic burden to the electric power industry, especially the thermal power generation industry. Therefore, this study takes Guangdong Province as an example to optimize the power generation mix with the objective of minimizing the total economic cost after the innovative introduction of the carbon quota auction mechanism and constructs an optimization model of the power generation mix based on the auction ratio by comprehensively applying the system dynamics model and the multi-objective linear programming model and systematically researches the power generation structure under different auction ratios with the time scale of months and quantitatively evaluates the economic inputs needed to reduce the greenhouse gas emissions.The results of the study show that after comprehensively comparing the total economic cost, renewable energy development and carbon emissions, it is the most scientific and reasonable to set the auction ratio of carbon allowances at 20%, which achieves the best level of economic and environmental benefits.

The purpose of this paper is to summarize and share the field experiment results of KEPCO's project consortium to create a TSO-DSO-DERA interaction scheme. The field experiment was conducted based on the prequalification algorithm proposed in the previous research from the same consortium and was designed to verify the validity of the algorithm under realistic grid conditions. In addition, during the course of the field experiment, it was found that points that were missed or not given much importance in the existing prequalification algorithm could affect the completeness of the overall system, and then practical improvements were made to improve it. The demonstration results confirm that the proposed algorithm is effective in real-world grid environments and can help DSOs ensure the reliability of the distribution system while supporting DERA's participation in the wholesale market using the proposed prequalification scheme.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

Bianchi type III string cosmological models (massive and geometric) in presence of magnetic field with vacuum energy density following the techniques used by Letelier (1979) and Stachel (1980) are obtained. We find that the energy conditions (dominant as well as weak) given by Hawking and Ellis (1974) are satisfied for the models. Also the solutions obtained satisfy conservation equation for massive string with magnetic field and vacuum energy density. The models in general, represent anisotropic phase of space-time due to the presence of string. However, the models isotropize at late time and in special case. It has also been shown that the magnetic field is directly linked with the matter. For string dust model, the state finder parameters {r,s} are in excellent agreement with Planck results (Sahni et al. (2003)). The physical and geometrical aspects of the models with special cases are also discussed.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

The aim of this work was to determine the potential of using a pulsed electric field (PEF) and ultra-sound (US) apparatus to produce mitragynine extracts from Mitragyna speciosa dried leaves. Four modes of the device were tested: PEF, US, US + PEF, and PEF + US. The results were compared with extracts obtained using a conventional technique (maceration, as the control). Changes in the mitragynine content were determined with the liquid chromatography/mass spectrometry (LC-MS/MS) method. The LC-MS/MS analysis showed that the mitragynine contents from kratom extracts using four different modes were different. The highest extraction (106.63 ± 0.85 mg/L) of mitragynine was achieved by the PEF + US procedure, followed by US + PEF (97.27 ± 1.33 mg/L), with increased extraction efficiencies of 45.81 ± 0.59% and 33.00 ± 1.85%, respectively. Moreover, the total energy consumption under the combination technique was 25.0% lower than that with PEF assistance. Furthermore, scanning electron microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) provided confirmatory evidence for the extraction of M. speciosa by the prototype. This study confirmed that PEF and US devices can be considered a green alternative method and may contribute to the application of agricultural products.

Information and communication technologies (ICT) are increasingly permeating our daily life and we ever more commit our data to the cloud. Events like the COVID-19 pandemic put an exceptional burden upon ICT infrastructures. This involves increasing implementation and use of data centers, which increased energy use and environmental impact. The scope of this work is to take stock on data center impact, opportunities, and assessment. First, we estimate impact entity. Then, we review strategies for efficiency and energy conservation in data centers. Energy use pertain to power distribution, IT-equipment, and non-IT equipment (e.g. cooling): Existing and prospected strategies and initiatives in these sectors are identified. Among key elements are innovative cooling techniques, natural resources, automation, low-power electronics, and equipment with extended thermal limits. Research perspectives are identified and estimates of improvement opportunities are presented. Finally, we present an overview on existing metrics, regulatory framework, and bodies concerned.

The energy efficiency of ice hockey arenas is a central concern for the administrations, as these buildings are well known to consume a large amount of energy. Since they are composite, complex systems, solutions to such a problem can be approached from many different areas, from managerial to technological to more strictly physical. In this paper we consider heat transfer processes in an ice hockey hall, during operating conditions, with a bottom-up approach based upon on-site measurements. Detailed heat flux, relative humidity and temperature data for the ice pad and the indoor air are used for a heat balance calculation in the steady-state regime, which quantifies the impact of each single heat source. We then solve the heat conduction equation for the ice pad in transient regime, and obtain a generic analytical formula for the temperature profile that can be used in practical applications. We then apply this formula to the resurfacing process for validation, and find good agreement with an analogous numerical solution. Since it is given with implicit initial condition and boundary conditions, it can be used not only in ice hockey halls, but in a large variety of engineering applications.

The UK Government is committed to reducing greenhouse gas (GHG) emissions by 80% by 2050. Buildings are responsible for 37% of the total GHG emissions in the UK and the need to reduce their emissions has resulted in more stringent building regulations in the recent past. The regulations, energy rating systems and voluntary guidelines — all are primarily aimed at reducing the need for heating and associated energy use by increasing insulation and air-tightness. However, future climates are projected to be warmer than the present day. Internal gains dominated non-domestic buildings will likely overheat, the adaptation to which will require energy-intensive cooling solutions, thus defeating the purpose of heating-focused regulations. This research investigated the effects of warming climate on overheating, and energy use and resulting emissions in representative urban office spaces in London in the present-day and future climates using hourly dynamic thermal simulations. Findings suggest that more airtight and highly—insulated office buildings designed for heating—dominated temperate UK climate will overheat in the 2050s. Heating demand reduces but electricity consumption increases by 121% when hybrid cooling is adopted to ameliorate overheating. Despite the rise, adopting a mixed-mode ventilation strategy was one of the ways of achieving overall energy efficiency while meeting benchmark overheating and carbon emissions target in present and future climatic contradictions. Current heating-focused legislations need to be urgently re-evaluated to account for the effects of climatic variability and overheating risks.

The European Union's current pressure on Member States to adopt the Green Deal and the Fit for 55 package is leading to an accelerated drive to put in place measures to meet the 2030 climate targets. At the same time, many discussions at international bilateral meetings of EU country representatives raise the question of the realism of setting climate targets and therefore the ability to meet these commitments. The results elaborated in this analytical study offer a realistic picture of the possibilities of meeting strategic climate targets using the example of the use of forest dendromass for the ability to achieve a 22% share of renewable energy sources (RES) in gross final energy consumption by 2030 in the Czech Republic. The study points out that at present the use of forest dendromass from primary pro-duction is at its maximum and meeting the climate targets for increasing the share of RES in the energy mix represents a major problem in the long term. The findings published in this study also point to the objective threat of increased use of dendrmass in the energy sector to the maintenance of sustainable forest management and the preservation of forest quality.

Abstract. The purpose of this review is to investigate the nature of privacy concerns in the context of Smart Local Energy Systems (SLES) to understand how SLES providers can minimize both users’ concern, and cause for concern, around privacy. We conducted a rapid realist review and thematic framework analysis against Bronfrenbrenner’s socio-ecological model to understand privacy concerns in different contexts. A common privacy concern was that sharing detailed energy use data had the potential to reveal information about home life, and to intrude upon people’s sense of autonomy, choice and control. Evidence suggests that people are willing to accept newdata sharing technologies if the benefits of doing so are clear, anticipated, and mutually beneficial. Building trust, through increasing knowledge and understanding was a mechanism for overcoming privacy concerns, but this was mediated by the organization providing the information. Non-profit organizations were more trusted to ensure appropriate safeguards to privacy were in place. One key barrier to participation with good supporting evidence was that people can resist perceived intrusions on their privacy. This could be actively resisted by refusing to install data collection technologies or passively by non-participation in adapting energy use behaviors: both of which are necessary for SLES to achieve their goals of managing energy demand and building resilience in smart grids.

Herein is introduced a simple scalar field model derived from classical based kinetic energy, gravitational potential energy, and Special Relativity’s rest mass energy. By applying a classical orbit over the scalar field, relativistic effects are predicted. The scalar field is then applied to a classical model of the Hydrogen atom resulting in a relativistic effect equal to the binding energy of the Hydrogen atom. In addition, the model derives the fine structure constant due to the gravitational effect. The relativistic effects are then discretized in increments equal to the model’s gravitational induced constant. The discretization produces the Hydrogen atom spectral emissions and an angular moment equal to Planck’s reduced constant. The model is not presented as a replacement for current theory, rather it is for inspection and illustration of how a simplistic model may offer a fundamental bridge between the more complex, time proven theories of General Relativity and Quantum Mechanics.

I examine the groups which underly classical mechanics, non-relativistic quantum mechanics, special relativity, relativistic quantum mechanics, quantum electrodynamics, quantum flavourdynamics, quantum chromodynamics, and general relativity. This examination includes the rotations SO(2) and SO(3), the Pauli algebra, the Lorentz transformations, the Dirac algebra, and the U(1), SU(2), and SU(3) gauge transformations. I argue that general relativity must be generalized to Einstein-Cartan theory, so that Dirac spinors can be described within the framework of gravitation theory.

1) Background: The environmental, financial and social questions in Africa remain unanswered up-to-date, with the rapid increase in human population and the demand for fuel energy, trigger the need to generate data on the socio-economic factors influencing the knowledge of use and adoption of family-sized bio-digesters. The increasing prices of fossil fuels and taxes on energy sources require finding the alternative, clean and economical sources of energy for households in developing countries. Moreover, in Africa, the consumption of firewood and charcoal continues to increase, with wood fuel consumption predicted to increase by 2030 to over 140%. The study objectives were 1) to determine the socio-economic characteristics of the people in Ngoma district, 2) to assess socio-economic factors influencing people to use and adopt family-sized bio-digesters. 2) Methods: Quantitative data collected with semi-structured questionnaires and interviews were analyzed using descriptive statistics. 3) Results: The results show that many households had not realized the potential benefits of biogas use and adoption in Rwanda. The study further found that a number of factors such as household income levels, socio-economic, technological, and institutional influence the household use and adoption of biogas energy. 4) Conclusions: At the end, the study suggests the need for all players such as Government, Non-Governmental Organizations (NGO's) and local communities to work together to provide incentives and favorable environment that can attract individual households to invest in biogas energy production and utilization.

As the EU is moving towards a low carbon economy and seeks to further develop its renewable energy policy, this paper quantitatively investigates the impact of plausible energy market reforms from the perspective of bio-renewables. Employing a state-of-the-art biobased variant of a computable general equilibrium model, this study assesses the perceived medium-term benefits, risks and trade-offs which arise from an advanced biofuels plan, two exploratory scenarios of a more 'sustainable' conventional biofuels plan and a 'no-mandate' scenario. Consistent with more recent studies, none of the scenarios considered present significant challenges to EU food-security or agricultural land usage. An illustrative advanced biofuels plan simulation requires non-trivial public support to implement whilst a degree of competition for biomass with (high-value) advanced biomass material industries is observed. On the other hand, it significantly alleviates land use pressures, whilst lignocellulose biomass prices are not expected to increase to unsustainable levels. Clearly, these observations are subject to assumptions on technological change, sustainable biomass limits, expected trends in fossil fuel prices and EU access to third-country trade. With these same caveats in mind, the switch to increased bioethanol production does not result in significant market tensions in biomass markets.

The COVID-19 epidemic and the measures adopted to contain it have had a significant impact on energy patterns throughout the world. The pandemic and movement restrictions led to unpredictable fluctuations in power systems demand and the fuel price for a delayed period. Monkeypox, another viral disease, appeared during the post-COVID period. It is assumed that the outbreak of monkeypox is unlikely due to the implication of preventive measures experienced by COVID-19. At the same time, the probability of an epidemic cannot be blindly overlooked. This paper aims to examine and analyze historical data to look at how much petroleum fuel was used for generating power and how the price of petroleum fuel changed over seven years, from January 2016 to August 2022. This period covers the time before the COVID-19 pandemic, during the pandemic, and after the pandemic. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and Snaïve), Seasonal and Trend decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods have been applied for both fuel consumption and price prediction. The best forecasting method for fuel price and consumption has been identified among these methods. The paper also utilizes the ARIMAX model by incorporating multiple exogenous variables, such as monthly mean temperature, mean fuel price, and mileage of vehicles traveling during a certain period of pandemic lock-down. It will assist in capturing the non-smooth and stochastic pattern of fuel consumption and price due to the pandemic by separating the seasonal influence and thus provide a prediction of the consumption pattern in the event of any future pandemic.

The Kabul River basin (KRB) of Afghanistan, a lifeline of around 10 million people, has multiplicity of governance, management and development related challenges leading to inequity, inadequacy and unreliability of irrigation water distribution. Prior to any uplifting intervention, there is a need to evaluate the performance of irrigation system on long term basis to identify the existing bottlenecks. Although there are several indicators used for the performance evaluation of the irrigation schemes, but we used the coefficient of variation (CV) of actual evapotranspiration (ETa) in space (basin, sub-basin, and provincial level), relative evapotranspiration (RET) and temporal CV of RET to assess the equity, adequacy and reliability of water distribution respectively, from 2003 to 2013. The ETa was estimated through surface energy balance system (SEBS) algorithm and the ETa estimates were validated using advection aridity (AA) method with R2 value of 0.81 and 0.77 at Nawabad and Sultanpur stations respectively. The global land data assimilation system (GLDAS) and moderate-resolution imaging spectroradiometer (MODIS) products were used as main inputs to the SEBS. Results show that mean seasonal sub-based RET values during summer (May – September) (0.37 ± 0.06) and winter (October – April) (0.40 ± 0.08) are below the target values (RET ≥0.75) during 2003-2013. The CV of mean ETa within sub-basins and provinces for the entire study period has equitable distribution of water from October-January (0.09±0.04) whereas the highest inequity (0.24±0.08) in water distribution is during early summer. The range of the CV of mean ETa (0.04-0.06) on monthly and seasonal basis shows the unreliability of water supplies in several provinces or sub-basins. The analysis of temporal CV of mean RET highlights unreliable water supplies across the entire basin. The maximum ETa during the study period was estimated for Shamal sub-basin (552±43mm) while among provinces Kunar experienced the highest ETa (544±39mm). This study highlights the dire need for interventions to improve the irrigation performance in time and space. The proposed methodology can be used as a framework for monitoring and implementing the water distribution plans in future.

Shallow Geothermal Energy (SGE) exchanges heat with the ground. In continuous long-term operation, the initial temperature field can be disturbed, and subsurface thermal plumes can be developed. In this paper, the thermal impact of a SGE system under Mediterranean climate is handled. Temperature recordings from 104 thermal probes placed in depth along 15 monitoring boreholes are analysed. Those boreholes were drilled 1-2m from thermos-active boreholes of the case study system installed in a university building. The analysis handles one year of SGE system operation. Temperature depth profiles, reaching up to 140 m depth, were registered with a 10-minute time-step resulting in a large amount of data. Ground thermal conductivity was estimated experimentally and semi-empirically allowing to compute the initial undisturbed ground temperature profiles and compare it with the monitored values. Climate data was recorded by the university meteorological station. Globally, the measured and computed data were coherent and a non-negligible impact of the SGE system operation in the first year was observed. The building orientation as well as the nearby departments had significant impacts on shallow ground temperature. Maximum ground temperature changes, ranging from 2 to 3º C as observed in different boreholes indicating that the system is operating efficiently.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

The issue of water and energy crisis have been turned into global matters which need to be tackled jointly. Accordingly, floating solar power plants, in which photovoltaic modules are used on the surface of water infrastructures, has recently been attracting much interest. This system provides some additional advantages over the ground-based system such as conserving the land and the water and increasing the efficiency of the module. This study first reviews the relevant literature comprehensively and then evaluates the potential of using floating solar photovoltaic (FSPV) on some of Iran’s water infrastructures which have experienced a large amount of evaporation every year due to high solar radiation. To this end, the five important dam reservoirs are selected as the representatives of the five important watersheds in Iran, and the advantages of the FSPV plant is analyzed in terms of energy generation, evaporation reduction, economic and environmental aspects considering different coverage percentages of reservoir’s surfaces. Considering Iran's vast potential for solar radiation, and, on the other hand, huge energy demand and critical water situation, results indicated that Iran can effectively harness solar energy through FSPV systems which help conserve the water in addition to support sustainable energy production.

Investments in wind and solar power are driven by the aim to maximize the utilization of renewable energy (RE). This results in an increased concentration of wind farms at locations with higher average wind speeds and of solar panel installations at sites with higher average solar insolation. This is unfavourable for energy suppliers and for the overall economy when large power output fluctuations occur. Thus, when evaluating investment options for spatially distributed RE systems, it is necessary to model resource fluctuations and power output correlations between locations. In this paper, we propose a methodology for analyzing the spatial dependence, accurate modeling, and forecasting of wind power systems with special consideration to spatial dispersion of installation sites. We combine vine-copulas with the Kumaraswamy distribution to improve accuracy in forecasting wind power from spatially dispersed wind turbines and to model solar power generated at each location. We then integrate these methods to formulate an optimization model for allocating wind turbines and solar panels spatially, with an end goal of maximizing overall power generation while minimizing the variability in power output. A case study of wind and solar power systems in Central Ontario, Canada is also presented.

Turning ships in port turning basins is an important and responsible operation, mainly involving the ship itself and the port tugs. Such operations involve many maneuvers that consume a lot of energy (fuel) and emit a lot of emissions. Turning basins in harbors and quay approaches are in most cases relatively shallow. The paper examines the turning of ships in port turning basins using harbor tugs, the effect of shallow depth on ship turning, energy (fuel) consumption and the generation of emissions during such maneuvers of harbor tugs. The paper presents the developed theoretical models, and the experimental results on theoretical models, which were verified on real ships and using calibrated simulators. Discussions and conclusions prepared on the basis of the research base. The use of the developed methodology makes it possible to increase shipping safety, optimize maneuvers and reduce energy (fuel) consumption when turning ships in the port and at the same time reduce the amount of fuel consumed by port tugs and reduce the number of emissions of tugs during such operations.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

The major aim of this study was to investigate and explores the linkage between economic growth, electricity access, energy use and population growth in Pakistan. To check the variables stationarity, Augmented Dickey-Fuller (ADF) and Phillips-Perron unit root test was applied and an Autoregressive Distributed Lag (ARDL) bounds testing approach to co-integration was applied to investigate the dynamic causality link among the study variables. These tests shed light on the long-run connection among the variables; further, the results revealed that electricity access to population, electricity access to urban population, energy usage, population growth, and urban population growth had a significant impact on economic growth, while the electricity access to rural population and rural population growth has a negative impact on the economic growth in Pakistan. According to these findings, study commends that government of Pakistan pay further attention to increase its electricity production from different sources including, hydroelectric, solar, oil and gas and nuclear in order to fulfill the country’s demands. By using ARDL bounds testing approach, this study filled the literature gap regarding economic growth, electricity access, energy use and population growth in Pakistan.

This paper proposes how to reduce the consumption of active electrical energy (kwh) by 90.3% while maintaining the same mechanical work speed (RPM) at variable torque loads (fans or air-fluid blowers, centrifugal pumps are not included). of water and similar fluids), by using the “Fan Law” in an innovative way in PMSM-type synchronous motors (a comparative study never before carried out on the Fan Law). The work is carried out comparatively between brushless a-synchronous motors with starting loop (or motor with a short-circuited loop) versus brushed a-synchronous motors and PMSM-type synchronous motors without the need to use VDF (variable frequency drives), simplifying technology (electronics) and saving costs in an innovative way (R+D+i). The case study was developed on a design applied to a centrifugal air extractor/blower with PMSM/IPM type synchronous motor. Applying one of the fan affinity laws –with the impeller diameter 10.5 (mm) constant- the electrical power absorbed by the blower motor is proportional to the cube of the shaft speed: . Being “P” power (Watts) and “N” speed (RPM). Carrying out a comparative study between power (watts), active energy consumption (kwh) and rotational speed (RPM). This has a direct impact on the costs of residential and commercial single-phase active electrical energy consumption, measured in kilowatt-hours (kwh). Carrying out a comparative study between three (3) types of alternating current (AC) electrical machines, according to the NEMA (National Electrical Manufacturers Association); AC motors fall into three (3) categories. One (1), synchronous motors (Syncrhonous Motor) of three types: (1a) excitation by DC (DC Excited Motor), (1b) permanent magnet (Permanent Magnet Motor) and (1c) reluctance motor (Reluctance Motor) or motor Step by Step. Two (2), asynchronous induction motors of two types: (2a) Squirrel-Cage Induction Motor and (2b) Wound-Rotor Induction Motor. Three (3) series-wound motor (Series-Wound Motor) also called universal motor (they have carbons).

Liability to prevent consequences of an unhealthy situation due to accumulating toxic and hazardous emissions caused by open dumping of municipal solid waste with increasing urbanization has necessitated a renewed thinking on waste disposal. Grate fired incineration systems were adopted by urban managements in past and present but with criticisms due to formation of air borne emissions. Improved combustion methods like fluidized bed are now propagated because of current requirements like efficient energy recovery potential, stricter emission norms, adaptability with urban growth, adaptability to co-firing with other waste like biomass, edible oil wastes or industrial effluent and integration with conventional energy generation. Such a comprehensive and futuristic approach is more sustainable for the community. Multi-criteria decision-making tool is used to identify the best technology option among grate combustion and fluidized bed combustion for disposing and energy recovery from waste. Ten different collection and disposal options involving two combustion methods, namely, grate combustion and fluidized bed method are considered. Utilization of the energy is done for three end uses, namely, power generation, water distillation and district cooling. Two different regions in Saudi Arabia are considered for this study under two types of scenario, namely with recycling and without recycling. The different options are prioritized based on their overall ranking using five major performance factors.

As an important support for power system with high penetration of renewable energy, energy storage system (ESS) has changed the traditional model of simultaneous implementation of electricity production and consumption, and its installed capacity under the source-grid-load scenario is rising year by year, but it faces the problems of insufficient utilization and benefits. This study analyzes the functional combination of ESS under the source-grid-load scenarios, and proposes a comprehensive benefit evaluation method of energy storage projects based on fuzzy decision-making trial and evaluation laboratory (DEMATEL) and super efficiency data envelopment analysis (DEA) model, which considers the perspective of economic and social environment. Firstly, the functional requirements of energy storage on the source-grid-load scenarios are explored respectively, and the characteristics of various functions are analyzed to form functional combination schemes. Secondly, index modeling is carried out from three aspects: the whole life cycle cost, functional combination benefit and social environmental benefit, and the comprehensive benefit evaluation index system of energy storage project is proposed, which includes both economic and social environment. Then, the intuitionistic trapezoidal fuzzy number is combined with DEMATEL to form an effective analysis method for the input-output relationship of the indexes, and the comprehensive evaluation is realized based on the super efficiency DEA model. Finally, the effectiveness of the proposed evaluation method and the rationality of the functional combination are verified under source-grid-load scenarios respectively.

In various domains such as energy, manufacturing, and maritime, cyber-physical systems (CPS) have seen increased interest. Both academia and industry have focused on the cybersecurity aspects of such systems. The assessment of cyber risks in CPS is a popular research area with many existing approaches that aim to suggest relevant methods and practices. However, few works have addressed the extensive and objective evaluation of the proposed approaches. In this paper, a standard-aligned evaluation methodology is presented and empirically conducted to evaluate a newly proposed cyber risk assessment approach for CPS. The approach, which is called FMECA-ATT&CK is based on Failure Mode, Effects & Criticality Analysis (FMECA) risk assessment process and enriched with the semantics and encoded knowledge in the Adversarial Tactics, Techniques, and Common Knowledge framework (ATT&CK). Several experts were involved in conducting two risk assessment processes, FMECA-ATT\&CK and Bow-Tie, against two use cases in different application domains, particularly an autonomous passenger ship (APS) as a maritime use case and a digital substation as an energy use case. This allows for the evaluation of the approach based on a group of characteristics, namely, applicability, feasibility, accuracy, comprehensiveness, adaptability, scalability, and usability. The results highlight the positive utility of FMECA-ATT&CK in model-based, design-level, and component-level cyber risk assessment of CPS with several identified directions for improvements. Moreover, the standard-aligned evaluation method and the evaluation characteristics have been demonstrated as enablers for the thorough evaluation of cyber risk assessment methods.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

In our previous papers [1,3], using only the concepts of the zero-point energy and quantized space–times, all the fields including gravity were explained. However, the previous papers had the following limitations: First, the concept of the quantized space-time must be experimentally confirmed. Second, we should clarify the meaning of the quantized Einstein’s gravity equation, which is derived in [1]. Moreover, in another paper [2], we succeeded in describing the neutrinos’ self-energy and their oscillations. However, this paper assumes the rest energy of 3-leptons in advance, which is why we needed to uncover the reason why leptons have 3-generations. As mentioned, using the concepts of the zero-point energy and quantized space–times, we derived the quantized Einstein’s gravity equation in our previous paper [1]. The paper provides an analytical solution of this equalized Einstein’s equation, which implies the conservation of angular momentum in terms of quantized space–times. Employing this solution and without the standard big bang model, a unique form of acceleration equation for the acceleration-expansion universe is derived. Moreover, the temperature of the cosmic microwave background (CMB) emission is also obtained. Further, this solution results in an analytical (not numerical) derivation of the gravity wave. Moreover, based on the configuration of quantized space–times in terms of both electric and magnetic fields, we analytically attempted to calculate every equation in terms of electromagnetic and gravity fields, using the solution of the quantized Einstein’s gravity equation. As a result of this theory, first the calculated acceleration and temperature of CMB emission agree with the measurements. Furthermore, the analytical solution of the quantized Einstein’s gravity equation resulted in all the laws of electromagnetic and gravity fields in addition to the analytically derived gravity wave, which agrees well with the recent measurements. Moreover, the calculations of the energies in the basic configuration of the quantized space–times resulted in all 3-leptons’ rest energies. Considering this basic configuration is uniformly distributed everywhere in the universe, we can conclude that τ-particles or static magnetic field energy derived from the basic configuration of the quantized space–times is the identity of dark energy, which also distributes uniformly in the universe.

Under high-frequency operating conditions, the high-speed solenoid valve (HSV) experiences energy loss and heat generation, which significantly impact its operational lifetime. Reducing the energy loss of HSV without compromising its opening response characteristics poses a significant challenge. To address this issue, a finite element simulation model of HSV coupled with a current feedback model is constructed to investigate the synergistic effects of dynamic response and energy loss. Predictive models for the opening response time, HSV driving energy, and Joule energy using Back Propagation neural network (BPNN) are established. Furthermore, a multi-objective optimization study on the current driving strategy using Non-dominated Sorting Genetic Algorithm II (NSGA-II) is conducted. After optimization, although there was a 6.24% increase in the opening response time, both HSV drive energy and Joule energy were significantly reduced by 15.67% and 22.49%, respectively. The proposed multi-objective optimization method for HSV driving strategy holds great significance in improving its working durability.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

Buildings’ thermal energy needs are inherently linked to climate conditions. Consequently, it is crucial to evaluate how climate changes affect these energy demands. Despite extensive analysis, a comprehensive assessment involving a diverse range of building types has not been consistently conducted. The primary objective of this research is to perform a coherent evaluation of the influence of climate changes, construction element properties, and the Heating, Ventilation, and Air Conditioning (HVAC) system type of control on the energy requirements of six buildings (residential, services, and commercial). The buildings are considered located in a temperate Mediterranean climate. Our focus is on the year 2070, considering three distinct climatic scenarios: (i) maintaining the current climate without further changes, (ii) moderate climate changes, and (iii) extreme climate changes. The buildings are distributed across three different locations, each characterized by unique climatic conditions. Buildings’ envelope features a traditional External Thermal Insulation Composite System (ETICS) and expanded polystyrene (EPS) serves as thermal insulation material. Two critical design factors are explored: EPS thickness ranging from 0 (no insulation) to 12 cm; and horizontal external fixed shading elements varying lengths from 0 (absence) to 150 cm. Six alternative setpoint ranges are assessed for the HVAC system control: three based on the Predicted Mean Vote (PMV) and three based on indoor air temperature (Tair). Results were obtained with a validated in-home software tool. They show that, even under extreme climate conditions, the application of thermal insulation remains energetically favorable, however its relative importance diminishes as climate severity increases. Then, proper insulation design remains important for energy efficiency. The use of external shading elements for glazing (e.g., overhangs, louvers) proves beneficial in specific cases. As climate changes intensify, the significance of shading elements grows. Thus, strategic placement and design are necessary for good results. The HVAC system’s energy consumption depends on the level of thermal comfort requirements, on the climate characteristics and on the building’s type of use. As climate change severity intensifies, energy demands for cooling increase, while energy needs for heating decrease. However, it’s essential to recognize that the impact of climate changes on HVAC system energy consumption significantly depends on the type of building.

Methane and carbon dioxide are the main contributors to global warming, being the methane effect twenty-five times more powerful than carbon dioxide. Although the sources of methane are diverse, it is a very volatile and explosive gas. One way to store the energy content of methane is its conversion to methanol. Methanol is liquid under ambient conditions, easy to transport and, apart from its use as an energy source, it is a chemical platform that can serve as a starting material for the production of various higher value-added products. Accordingly, the transformation of methane to methanol has been extensively treated in the literature, using traditional catalysts as different types of zeolites. However, in the last years, a new generation of catalysts have emerged to carry out this transformation with higher conversion and selectivity, and more importantly, under mild temperature and pressure conditions. These new catalysts typically involve the use of a highly porous supporting material such as zeolite, or more recently, metal-organic frameworks (MOFs) and graphene, and metallic nanoparticles or a combination of different types of nanoparticles that are the core of the catalytic process. In this review, the characteristics, the catalytic mechanisms, reactors, and the main results of these catalysts are presented as a way to overcome the challenges found in traditional catalysts.

The A.C.Q.U.A. (Advisable Conscious Quality Use from Assisi) project, promoted by the Climate and Energy and Heritage Design courses of the Planet Life Design Master Program, addresses the theme of the recovery and regeneration of ancient wash-houses in the context of energy, environmental sustainability and innovation, a way of understanding cultural heritage in the wider sense of heritage community through the active participation of all the actors involved: universities, institutions, businesses, students and citizens. The proposal, tested in the municipalities of Assisi and Ruviano (ITALY), involves the creation of a "Community Wash House", a new way of carrying out the usual domestic act of washing clothes in the open air, next to the places where this rite was traditionally performed, in technologically innovative constructions that use renewable energy sources and encourage a reduction in household consumption of water and energy. This project is part of the training of professionals in the new inter-university course that combines knowledge of the tools of technical and scientific design with historical and cultural perspectives in a perspective of sustainable redevelopment of existing structures in the area and the use of alternative energy sources with low climate impact, calculated using the statistics of the Copernicus CDS.

To solve the problem of energy constraint and spectrum scarcity for cognitive radio wireless sensor networks (CR-WSNs), an underlay decode-and-forward relaying scheme is considered, where the energy constrained secondary source and relay nodes are capable of harvesting energy from a multi-antenna power beacon (PB) and using that harvested energy to forward the source information to the destination. Based on the time switching receiver architecture, three relaying protocols, namely, hybrid partial relay selection (H-PRS), conventional opportunistic relay selection (C-ORS), and best opportunistic relay selection (B-ORS) protocols are considered to enhance the end-to-end performance under the joint impact of maximal interference constraint and transceiver hardware impairments. For performance evaluation and comparison, we derive exact and asymptotic closed-form expressions of outage probability (OP) and throughput (TP) to provide significant insights into the impact of our proposed protocols on the system performance over Rayleigh fading channel. Finally, simulation results validate the theoretical results.

The main goal of the review is to provide a summary and an assessment of the potential of fast-growing tree species for suitable transformation of agroforestry areas for biomass production in the Baltic Sea region. The article summarizes the research on the management process of agroforestry zones by establishing short rotation plantations with tree species Salix spp., Populus spp., Alnus spp. and looks at the perspectives of planning of these zones as biomass producers. Short rotation forestry (SRF) with a combination of species and a rotation time of 15 to 30 years, depending on the species used, is the most suitable approach for management of these agroforestry zones. Willows (Salix spp.) and poplars (Populus spp.) are suitable for short rotation coppice (SRC), as these tree species can be harvested at much shorter intervals, respectively, 1–5 and 4–10 years, facilitating their use in agricultural systems. In Alnus spp. short rotation plantation the life cycle for energy wood production is assumed to be 15-30 years. The black alder plantations in agroforestry zones are used for sawnwood and firewood production, with a rotation span of 20–40 years. Calculated economic agroforestry zone repayment period is about 10-15 years, if costs and prices as in 2021 are used.

In two previous papers, we calculated the dielectrophoresis (DEP) force and corresponding trajectories of high- and low-conductance 200-µm 2D spheres in a square 1x1mm chamber with plane-versus-pointed, plane-versus-plane and pointed-versus-pointed electrode configurations by applying the law of maximum entropy production (LMEP) to the system. Here, we complete these considerations for configurations with four-pointed electrodes centered on the chamber edges. The four electrodes were operated in either object-shift mode (two adjacent electrodes opposite the other two adjacent electrodes), DEP mode (one electrode versus the other three electrodes), or field-cage mode (two electrodes on opposite edges versus the two electrodes on the other two opposite edges). As in previous work, we have assumed DC properties for the object and the external media for simplicity. Nevertheless, every possible polarization ratio of the two media can be modeled this way. The trajectories of the spherical centers and the corresponding DEP forces were calculated from the gradients of the system’s total energy dissipation, described by numerically-derived conductance fields. In each of the three drive modes, very high attractive and repulsive forces were found in front of pointed electrodes for the high and low-conductance spheres, respectively. The conductance fields predict bifurcation points, watersheds, and trajectories with multiple endpoints. The high and low-conductance spheres usually follow similar trajectories, albeit with reversed orientations. In DEP drive mode, the four-point electrode chamber provides a similar area for DEP measurements as the classical plane-versus-pointed electrode chamber.

Assuming a two component, positive and negative mass, superfluid/supersolid for space (the Winterberg model), we model the Higgs field as a condensate made up of a positive and a negative mass, planckion pair. The connection is shown to be consistent (compatible) with the underlying field equations for each field, and the continuity equation is satisfied for both species of planckions, as well as for the Higgs field. An inherent length scale for space (the vacuum) emerges, which we estimate from previous work to be of the order of,

Issues related to safe and abundant energy production have been prominent in recent years. This is particularly tr ue when society considers how to increase the quality of life by providing low-cost energy to citizens. A significant concern of the Gulf Cooperation Council (GCC) relates to the environmental effects of energy production and energy use associated with climate change. Efforts to reduce fossil fuel use and increase the use of renewable energy, together with the price volatility of fossil fuels, have seriously impacted the economics of many of the oil-producing countries, particularly the Gulf States, which has led to efforts to make their economies more diverse and less dependent on oil production.

Organic farming has positive, impact on environment, soil health, and healthy food quality. Worldwide demand for organic foods is increasing by leaps and bounds in recent years. The present investigation was undertaken during 2014 to 2018 to evaluate the effect of cowpea (Vigna unguiculata) co-culture with maize (Zea mays L.) on productivity enhancement over prevailing maize-fallow system, and to assess the feasibility of inclusion of short duration winter crops after maize with appropriate residue management practices on productivity and soil health. The experiment comprised of six cropping systems in main plot and three soil moisture conservation (SMC) measures options in sub plot. Results indicated that the inclusion of second crop in place of fallow and cowpea co-culture with maize increased average maize grain yield by 6.2 to 23.5% as compared to that of maize-fallow (MF). Use of maize stover mulch (MSM) + weed biomass mulch (WBM) increases maize grain yield by 19.1 and 6.5% over those of MSM and no mulch (NM), respectively. Various soil moisture conservation (SMC) measures had significant (p=0.05) effect on crop yields and water productivity. Double cropping system had significantly (p=0.05) higher amount of soil available NPK, soil organic carbon (SOC), microbial biomass carbon (MBC) and dehydrogenase activity (DHA) at 0-15 cm and at 15-30 cm depth than those under MF. The SWC measures of MSM+WBM had significantly higher available N, SOC, and MBC by 5.5, 4.8 and 8.1% than those under NM, respectively. Correspondingly, soils under MSM and MSM+WBM had 2.24 and 2.99% lower bulk density (ρb) in 0-15 cm and 2.21 and 2.94% lower ρb in 15-30 cm than that of NM. The energy use efficiency (EUE) was significantly higher under MCV (7.90%) over rest of the cropping sequences. MSM+WBM and MSM recorded 25.1 and 16.6% higher net energy over NM, respectively. The net return (INR 159.99×103/ha) and B:C ratio (2.86) were significantly higher with MCV system followed by MCR cropping sequence. MSM+WBM had significantly higher net return (INR 109.44×103/h), B:C ratio (2.46) over those under MSM (INR 97.6×103/h) and NM (INR 78.61×103/h). Overall the cowpea co-culture with maize and inclusion of short cycle winter crops along with MSM+WBM in maize-based cropping systems was found productive in terms of crop and water, profitable, energy efficient and sustained the soil health.

The world is facing an energy crisis. Governments are seeking to provide universal energy access and guarantee energy security while trying to mitigate climate change. One possible solution is energy transitions towards low carbon energy systems. Among other things (physical infrastructure, public policy and regulatory enablers and knowledge and capacities) changes in the energy systems require a well informed and participative citizenship. Within this context the concept of energy literacy appears. Energy literacy is the understanding of how energy is generated, transported, stored, distributed and used, awareness about its environmental and social impacts and the knowledge to use it efficiently in the different sectors of the economy. This paper provides a systematic literature review in the Web of Science’s Core Collection. Most of the work done around energy literacy addresses its evaluation among different groups, particularly students at different levels, and the construction, application and evaluation of tools for improving energy literacy. Other frequently studied issues are the influence of energy literacy in decision making, its drivers and conceptual research about the topic. Energy enables citizens to effectively contribute to energy efficiency and sustainable development, nevertheless energy literacy is not strongly correlated to energy consumption habits.

The term sustainable energy is very familiar to all of us yet its exact definition or meaning has so far been vague. To date the widely adopted definition of sustainable energy has been inspired by the definition of sustainable development formulated more than 30 years ago in the Our Common Future - the UN’s Report of the World Commission on Environment and Development. The current definition conceals the true spirit of the Report and this has some ramifications. It raises the question as to whether we have put too much emphasis on attaining the future dimension of sustainability in the middle of the situation where the energy survivability is in fact the real issue in many parts of the world. In this paper the role of energy in sustaining livelihoods of low income communities is discussed. Existing definition of sustainable energy that the whole world seems to have embraced is looked at critically and its downsides exposed. The identified pillars of sustainable energy and the associated issues is discussed and the need for an additional pillar, i.e. affordability is discussed and called for. This paper will argue that global definition of sustainable energy seems inappropriate and should be jettisoned and a more realistic definition should be formulated, adopted and embraced at local (i.e. national or regional) level taking into account local attributes and factors. The current push for a transition from the reliance on conventional energy sources to ‘cleaner’ energy sources (generally associated with renewable energy) has further exacerbated the issue of energy affordability that has made the conditions even more dire for so many groups of the world population. In the midst of this situation, those who push for a rushed energy transition seem to be those who also produce unsustainably high carbon footprint but who can easily offset their carbon foot-print through the ‘net-zero’ concept.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

The Universe at last scattering is locally treated as an unbound gas. The internal kinetic energy of the gas effectively constitutes a scalar energy field. The gas’s adiabatic expansion is entropic, giving repulsive entropic pressure. Gas kinetic energy is converted into entropic energy gain (63%) and isoentropic work against gravity (37%) at a constant 63:37 ratio. A three-term expression of the gas’s Hubble parameter is derived and found to be exclusively dependent on its mass density. At last scattering, this model gives a Hubble constant that is 125% of the value found from the ΛCDM model. After partition of Universal mass into the cosmic web of galaxies and the intergalactic medium (IGM), expansion came mostly from the IGM, presently comprising about 84% of total Universal mass and 90% of its volume. The onset of star formation within the cosmic web increased the IGM’s kinetic energy through the action of starlight, giving free electrons as an additional repository. Many of these free electrons are suprathermal. Suprathermal energy from both electrons and protons comprises about half of the IGM’s total kinetic energy and is expressed in the ΛCDM model as “dark energy” Λ. Entropic pressure derives from thermodynamic laws not found within general relativity.

This article aims to assess the benefits of floor-slab insulation measures using extruded polystyrene (XPS) and polyisocyanurate (polyiso) insulation materials at various levels of insulation thicknesses for a detached residential building. The EnergyPlus simulation analysis was carried out within the seven energy zones (represented by eight locations) of South Africa in accordance with the South African national code for building energy efficiency (SANS10400-XA). The energy savings and payback periods due to use of the insulation over a lifecycle period of 50 years were assessed. Cape Town (zone 4) behaved differently from other locations and hardly benefitted from the application of floor-slab insulation measures. Generally, polyiso insulation performed better than XPS, for vertical gap insulation. For vertical gap insulation, lower insulation thicknesses required higher insulation depths to maximize energy savings. Similarly, lower insulation thicknesses required higher perimeter insulation widths to maximize energy savings, for the horizontal perimeter insulation method. The locations that benefitted most from vertical gap floor-slab insulation were Pretoria (zone2), Kimberley (zone6), Nelspruit (zone3), Fraserburg (zone7), Welkom (zone1), Mthatha (zone5), Ixopo (zone5H) and Cape Town (zone4) in that order. This order was almost similar with those for the horizontal perimeter floor-slab insulation and horizontal full floor-slab insulation methods.

Following an updated outlook of global energy production and utilization, we show through selected examples from both developing and developed countries how distributed generation from renewable energy sources, and from solar energy in particular, is the key solution to ending energy poverty across the world. Guidelines aimed at policy makers suggest a systems view of energy that will be instrumental in guiding the transition from fossil fuels to combustion-free renewable energy for all energy end uses.

This analysis focuses on identifying the most efficient and cost-effective method of supplying power to a remote site, exploring photovoltaics (PV) and small wind turbines as primary power sources, and evaluating battery banks and hydrogen storage fuel cell systems as potential storage options. The hydrogen storage system converts surplus renewable power into hydrogen through an elec-trolyzer, storing it for later use in a fuel cell when renewable sources produce less power, enabling efficient energy storage during peak production periods. A sensitivity analysis of wind speed and hydrogen subsystem cost was conducted to evaluate the hydrogen storage system's performance. The optimal system graph suggests that the hydrogen subsystem must significantly decrease in cost to rival the battery bank, and in most cases, both the hydrogen system and battery bank were recommended together, offering reliable and efficient power for the remote site. While the battery bank is presently the more feasible option for powering the remote site, continuous monitoring and evaluation of both systems, considering site location, energy needs, and available resources, are essential to determine the most suitable power supply approach as technology advances and costs evolve over time.

The water and wastewater sectors are energy-intensive, and so a growing number of utility companies are seeking to identify opportunities to reduce energy use. Though England’s water sector is of international interest, in particular due to the early experience with privatisation, for the time being very little published data on energy usage exists. We analyse telemetry data from Thames Water Utilities Ltd. (TWUL), which is the largest water and wastewater company in the UK and serves one of the largest mega-cities in the world, London. In our analysis, we (1) break down sectoral energy use into their components, (2) present a statistical method to analyse the long-term trends in use, as well as the seasonality and irregular effects in the data, (3) derive energy-intensity (kWh m³) figures for the system, and (4) compare the energy-intensity of the network against other regions in the world. Our results show that electricity use grew during the period 2009 to 2014 due to capacity expansions to deal with growing water demand and storm water flooding. The energy-intensity of the system is within the range of reported figures for systems in other OECD countries. Plans to improve the efficiency of the system could yield benefits in lower the energy-intensity, but the overall energy saving would be temporary as external pressures from population and climate change are driving up water and energy use.

This interdisciplinary work presents a novel patent pending method of inertial electrostatic confinement (IEC) fusion called the Nuclear Electromagnetic Shaping Accelerator Reactor (NESAR) that addresses all of the major failure problems with currently known methods of IEC fusion. A brief background of previous IEC methods that generate a negative potential well to accelerate ions for fusion will be reviewed and compared to the NESAR method of magnetic confinement. In addition, a direct comparison will be presented between the NESAR and the tokamak method of fusion. The NESAR method of fusion obtains the plasma oscillation and compression capabilities of a tokamak without producing the catastrophic magnetic reconnection disruptions that currently plague tokamaks. Since the NESAR can oscillate charged particles comparable to the tokamak, this work will briefly review the history of the tokamak, how sawtooth magnetic reconnection occurs, and how the NESAR precludes the occurrence of magnetic reconnection. This work will also review the beginnings of a novel theory that has obtained interest from the Defense Advanced Research Projects Agency (DARPA) which is currently interested in possibly supporting further research into the NESAR to explore this new theoretical concept. This novel theory is a unified field theory based upon the trajectory of charged particle movements within the NESAR. The NESAR is the only concept of magnetic confinement in the world that may have the capability to allow charge particles to collectively interact relatively to a solitary location. Due to this possible capability, there is a probability that the confined particles may experience curved trajectories that could allow them to experience the effects of curvature deviation. If curvature deviation occurs with these magnetically confined charged particles; then the deviated acceleration would allow for the electromagnet field to be propelled to a higher dimension that could influence spacetime. Finally, this work will review another theory that explains how pole reversals are observed by the National Aeronautics and Space Administration’s (NASA) coiled magnetic field detectors. This theory requires little to no postulations to be framed and it is purely based upon the trajectory of charged particles within the NESAR, Michael Faraday’s law of induction, and experimental observations of rotating plasmas.