The generation of eucalypt sawdust has increased in Uruguay with the expansion of pulp and paper industrial sites. Currently, most of this readily available feedstock is either not used or applied for producing heat and power by combustion in biomass boilers. In this work, eucalypt sawdust was subjected to steam explosion as the first step for cellulosic ethanol production within the biorefinery concept. The effect of sawdust moisture content, pretreatment temperature and residence time were evaluated, along with the influence of water washing of steam-exploded solids on enzymatic hydrolysis and fermentation yields. After steam explosion, 60% xylans and 97% acetyl groups were recovered mainly as oligomers and acetic acid in the pretreatment liquor. Eucalypt sawdust moisture content affected the enzymatic hydrolysis performance and glucan conversion efficiency. Water washing after pretreatment improved hydrolysis efficiencies and ethanol production yields by 10% with respect to the unwashed pretreated solids at the same experimental condition. The best ethanol yields were obtained using PSSF (pre-saccharification and simultaneous saccharification and fermentation) after pretreatment at 205°C for 10 min, using sawdust with an 8% moisture content. In this case, 227 L ethanol and 40 kg total xylose (including xylo-oligomers) were obtained per ton of dry eucalypt sawdust.

The scale and accessibility of passive global surveillance have rapidly increased over time. This provides an opportunity to calibrate the performance of models, algorithms, and reflectance ratios between remote sensing devices. Here we test the sensitivity and specificity of Eucalypt chlorophyll-a reflectance ratio (ECARR) and Eucalypt chlorophyll-b reflectance ratio (ECBRR) to remotely identify eucalypt vegetation in Queensland, Australia. We compare reflectance ratio values from Sentinel-2 and Planet imagery across four sites of known vegetation composition. All imagery was transformed to reflectance values and Planet imagery was additionally scaled to harmonize across Planet Scenes. ECARR can identify eucalypt vegetation remotely with high sensitivity, but shows low specificity and is impacted by the density of the vegetation. ECBRR reflectance ratios show similar sensitivity and specificity when identifying eucalypt vegetation but with values an order of magnitude smaller than ECARR. We find that ECARR was better at identifying eucalypt vegetation in the Sentinel-2 imagery than Planet imagery. ECARR can serve as a general chlorophyll indicator but is not a specific index to identify Eucalyptus vegetation with certainty.

(1) Selecting high-quality varieties with disease resistance by crossbreeding artificially is the most fundamental way to address the damage caused by Calonectria spp in eucalypt plantations. However, understanding the mechanism of the formation of disease-resistant heterosis in eucalypt is crucial for the success of crossbreeding. (2) Two eucalypt hybrids, susceptible EC333 (H1522 × unknown) and resistant EC338 (W1667 × P9060) were screened in our previous study on the infection of the isolates of Calonectria., which causes eucalypt leaf blight. RNA-Seq sequencing was performed on susceptible hybrid EC333, disease-resistant hybrid EC338 (W1667 × P9060), and their parents. A comparison was conducted between the the transcriptomic data sequenced and the reference genome of Eucalyptus grandis, and the The differential expression of genes and functional annotations between hybrids and parents was identified. (3) Gene differential expression analysis shows that there are 3912 differentially expressed genes between EC333 and EC338, with 1631 up-regulated and 2281 down-regulated. The expression trends of differential gene sets in P9060 and EC338 were similar. However, the expression trend of W1767 was opposite that of EC338. The similarity of expression levels and the advantage of stress resistance of E. pellita suggested that genes with significant differences in expression are likely to be related to disease resistance. The GSEA enrichment based on GO annotation revealed that the carbohydrate binding pathway (GO:0030246) is differentially expressed between EC338 and EC333. The gene pathway that differentially expressed between EC338 and EC333, was revealed by GSEA enrichment based on KEGG annotation, is Sesquiterpenoid and Triterpenoid biosynthesis (EGR00909). The Alternative Splicing analysis demonstrated that the AS events gene between EC338 and EC333 is LOC104426602. According to SNP analysis, EC338 has 626 more high-impact mutation loci than the male parent P9060, and 396 more than the female parent W1767, the maternal parent W1767 has 259 more mutation loci in the downstream region than EC338, while the male parent P9060 has 3107 fewer mutation loci in the downstream region than EC338. Additionally, EC338 has 9631 more mutation loci in the exon region than EC333. These findings suggested that the genetic pathways, specific gene regions, and their quantities might play crucial roles in the formation of heterosis linked to the resistance against eucalypt leaf blight. The modules were found in WGCNA, which were strongly and oppositely correlated with EC338 and EC333, such as module MEsaddlebrown is likely to be associated with leaf blight resistance. (4) The present study provides a detailed explanation of the genetic basis for the heterosis of resistance to eucalypt leaf blight, providing a basis for exploring genes related to resistance to eucalypt leaf blight.

The pharmaceutical industry usually utilizes either hydrophobic or hydrophilic substances extracted from raw plant materials for preparing a final product, However, the plant material waste still contain substances with an opposite solubility. The aim of this study was to enhance the comprehensive usability of plant materials by developing a new non-wasting extraction method for eucalypt leaves and by investigating the phytochemical and pharmacological properties of eucalypt extracts and their 3D-printed dosage forms. The present extraction method enabled to prepare both hydrophobic soft extracts and hydrophilic (aqueous) dry extracts. We identified total 28 terpenes in the hydrophobic soft extract. In the hydrophilic dry extract, total 57 substances were identified, and 26 of them were successfully isolated. The eucalypt extracts studied showed a significant antimicrobial activity against Staphylococcus aureus, Pseudomonas aeruginosa, Bacillus subtilis, Candida albicans, Corynebacterium diphtheriae gravis, and Corynebacterium diphtheriae mitis. The anti-inflammatory activity of the dry extract was studied with a formalin oedema model in mice. The maximum anti-exudative effect of the dry extract was 61.5% at a dose of 20 mg/kg. The composite gels of polyethylene oxide and eucalypt extract were developed, and the key process parameters for semi-solid extrusion (SSE) 3D printing of such gels were verified. The SSE 3D-printed preparations of novel synergistically acting eucalypt extracts could have uses in antimicrobial and anti-inflammatory medicinal applications.