In the present research, groups of nanolayered structures and nanohybrids based on organic green dyes and inorganic species are designated to act as fillers for PVA for inducing new optical sites and increasing its thermal stability through producing polymeric nanocomposites. In this trend, different percentages of Naphthol green B were intercalated as pillars inside the Zn-Al nanolayered structures to form green organic-inorganic nanohybrids. The two-dimensional green nanohybrids were identified by X-ray diffraction, TEM and SEM. According to the thermal analyses, the nanohybrid, which has the highest amount of green dyes, was used for modifying the PVA through two series. In the first series, three nanocomposites were prepared depending on the green nanohybrid as prepared. In the second series, the yellow nanohybrid, which was produced from the green nanohybrid by thermal treatment, was used to produce another three nanocomposites. The optical properties revealed that the polymeric nanocomposites depending on green nanohybrids became optical-active in UV and visible regions because the energy band gap decreased to be 2.2 eV. In addition, the energy band gap of the nanocomposites depended on yellow nanohybrids was 2.5 eV. The thermal analyses indicated that the polymeric nanocomposites are thermally more stable than that of the original PVA. Finally, the dual functionality of organic-inorganic nanohybrids that produced from the confinement of organic dyes and the thermal stability of inorganic species converted the non-optical PVA to optical-active polymer in a wide range with high thermal stability

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

Soil cadmium (Cd) contamination has become a serious problem in China. In this study, the goals of the field experiments were to understand how the application of nitrogen fertilizer at the full heading stage and filling stage reduced the uptake of Cd in rice by affecting the distribution of Cd in iron plaques on the root surfaces and subcellular in the root and flag leaf. The hydroponic culture experiments aimed to explore the effect of interaction or deficiency of nitrogen and cadmium on cadmium accumulation in rice at the late growth stage. The results showed that under the condition of having enough nitrogen supply during the early growth stage, applying nitrogen fertilizer during the full heading stage and filling stage resulted in a significant increase in the concentration of Fe and Cd on the root plaques at the milk stage and mature stage. Additionally, it increased the concentration and proportion of Cd in the soluble fraction of subcellular in the flag leaves at the milk stage. On the other hand, when there was a deficiency of nitrogen, the concentration of Fe in the root plaques increased significantly, while the concentration of Cd in the root plaques decreased significantly. Moreover, the proportion of Cd in the flag leaf cell walls increased significantly. Regardless of whether there was sufficient or deficient nitrogen supply during the early growth stage, applying nitrogen at the full heading stage reduced the Cd concentration in brown rice by 35.11% and 57.25%, respectively. Under hydroponic culture conditions with both Cd exposure and later-stage nitrogen supply significantly increased the Cd concentration in brown rice. However, in the absence of Cd, nitrogen supply significantly reduced the Cd concentration in brown rice. The accumulation of Cd in brown rice was significantly correlated with the accumulation of Fe and Mn at the late growth stage. Our findings indicate that when there is sufficient nitrogen nutrition during the early growth stage of rice, topdressing nitrogen fertilizer at the full heading stage combined with lime with mineral element fertilizers such as Fe and Mn is an effective approach to reduce the presence of cadmium in rice grains.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.