Recently, most countries suffering from global warming due to the waste gases coming out of the combustion engines used to generate electric power by traditional methods. Therefore, many countries are currently trying to find alternative solutions to this problem by using renewable energies such as solar energy, wind energy, and energy generated from the waves of the ocean and sea to overcome pollution problems. The waves of the seas and oceans have enormous and largely untapped energy, so this work presents an efficient way to use the energy of sea waves to generate electricity. And also, trying to be a way to produce electricity from wave energy in the future. The best suitable places along the shores of Jizan city were inspected to install the buoy system to revenue advantage of the wave supreme height to achieve the height amount of electrical energy. A mathematical model was made to analyze the wave energy and convert it into energy extracted by mechanical force. The mathematical analyzes used the data collected from satellite maps of the numerous severe waves in the Red sea of the Jazan area, and the data published in previous research along that area. It was found that the beach of the Al Shuqaiq area is the greatest for installing the buoy and obtaining the highest electrical energy due to the presence of the highest wave intensity, followed by the beach of the Baysh and Al Morgan area. Also, one of the objectives of this research is to study the design of a device powered by a buoy to use the waves of the Red Sea to generate electric power. The influence of the buoy system design parameters such as the buoy diameter, length of the cylinder, and the length of the connecting rod on the electrical energy generation from wave energy was investigated. The current device is designed with a gearbox to produce continuous power with a single electric generator. A floating mooring device uses the rise and fall of bulges to convert sea wave energy into electrical energy. The device consists of a float, arm, two wheels of different diameters, a gear set, and an electric generator. The effect of the design of several factors on the performance of the device for converting the sea waves energy into electrical energy, including the length of the buoy arm, the wave height by changing the cam diameter, and the conversion ratios between the gear set, to optimize the output power of the wave energy.

Influence of the volute design parameters on the stable operating range and the performance of a centrifugal compressor was investigated experimentally for the following design conditions. The volute casing surface roughness was changed from 0 to 200 µm in five steps and tested. The axial distance between the casing and the diffuser cascades (clearance) was varied in five steps as C/b₂ = 1.2, 2.4%, 3.6%, 4.8%, and 6% relative to the impeller exit width. The radial distance from the impeller blade exit to the diffuser vane inlet in (vaneless space radius) in six steps as C/r₂ = 1.03, 1.05, 1.07, 1.09, 1.11, and 1. 13 relatives to the rotor outlet radius. The volute outlet geometry of a symmetric and tangent with different area ratios from 0.4 to 0.9. Finally, the compressor has been tested experimentally with different pinched vaned diffuser distances relative to the impeller exit width of bp/b2 =1, 0.98, 0.96, 0.94, 0.92, and 0.9. These testes were carried at different compressor operating conditions, and the time variations of the static pressure were recorded using five high-frequency response pressure transducers. A hot-wire anemometer is used to measure the compressor flow rate. The rotating stall and surge at the vaneless zone after the impeller exit can be detected by analyzing the fluctuations of pressure signals and the power spectrum density by using the Fast Fourier Transformation analysis. The experimental results indicated that the compressor with volute casing surface roughness of 100mm gives about 10.9% enhancements in the stable operating and 1% in pressure rise coefficient. The best axial distance between the diffuser vanes and the casing is 2.4% of the impeller blade height and the compressor in this design gives about 12.4% improvements in the stable working range. The compressor with radial vaneless distance of 1.056 gives improvements of about 16.6% in the surge margin, 2% in the pressure recovery and 4% in pressure rise coefficients. The compressor with a pinched diffuser of b/bp of 0.98 gives an improvement of 20.8% in surge point.

The main objective of the present study was to investigate arsenate [As (V)] resistance genes in rice cultivars grown in arsenic contaminated Egyptian soil in order to genetically induce resistance against arsenic in the local rice varieties as well as defining contaminated rice grains and/or soil. Three local rice cultivars; Sakha 102-104 were cultivated on modified Murashige and Skoog Basal Medium (MS medium) containing elevated concentrations of arsenate (0.1, 1 and 10 mg/l). The three varieties showed different resistant attitudes against arsenate with Sakha 104 being the most resistant. Extracted messenger RNA (mRNA) from treated and untreated Sakha 104 plantlets was scanned using differential display to demonstrate the arsenate resistant genes using three different arbitrary primers. About 100 different RNAs with (1500 bp - 50 bp) were obtained from which seven were up-regulated genes, subjected to DNA cloning using TOPO TA system and the selected clones were sequenced. The sequence analysis described four genes out of the seven namely disease resistance protein RPM1, Epstein-Barr virus EBNA-1-like, CwfJ family protein and outer membrane lipoprotein OmlA while the other three genes were hypothetical proteins. It is concluded the four induced genes in the resistant rice cultivar considered as a direct response to arsenic soil pollution. Genes detected in the present study can be used as geno-sensors for rice grains and soil contamination with As (V). Moreover, local rice cultivars may be genetically modified with such genes to induce high resistance and to overcome arsenic soil pollution.