Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

The unpredictable increase in electrical demand affects the quality of theenergy throughout the network. A solution to the problem is the increase of distributedgeneration units which burn fossil fuels.While this is an immediate solution to theproblem the ecosystem gets affected by the emission of CO2.A promising solutionis the integration of Distributed Renewable Energy Sources (DRES) to the conventionalelectrical system, thus, introducing the concept of smart microgrids (SMG) that requirea safe, reliable and technically planned two-way communication system. This documentpresents a heuristic based on planning capable of providing a bidirectional communicationnear optimal route map, following the structure of an hybrid Fiber-Wireless (FiWi) with thepurpose of obtaining information of electrical parameters that help us to manage the useof energy by integrating conventional electrical system to SMG. A FiWi network is basedon the integration of wireless access and optical networks. This integration increases thecoverage and reliability at a lower cost. The optimization model is based on clusteringtechniques, through the construction of balanced conglomerates. The method is used forthe development of the clusters along with the Nearest-Neighbor Spanning Tree Algorithm(N-NST). Additionally, Optimal Delay Balancing (ODB) model will be used to minimizethe end to end delay of each grouping. In addition, the heuristic observes real designparameters such as: capacity and coverage. Using the Dijkstra algorithm, the routes arebuilt following the minimum shorter path. Therefore, this paper presents a heuristic able to plan the deployment of smart meters (SMs) through a tree-like hierarchical topology for theintegration of SMG at the lowest cost.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

A metering roundabout where traffic is controlled by traffic lights with phase times influenced by queue detector occupancy might be the solution to enhance performance when there are unbalanced traffic flows at roundabouts. There have, however, been minimal studies on how the distance of the queue detector from the stop line affects signal phase time durations and the queuing lengths. This research, therefore, seeks to develop a Cuckoo Search/Local search Algorithm using parameters such as arrival volumes, conflicting volumes, detector distance and phase time to investigate the relationship of signal setting, detector location and queuing formulations. Also, some additional statistical tests were performed for the fitness of the data. In order to conduct solid model validations, model output data was compared against the AIMSUN model. The results from the analyses demonstrated that the queue detector distance can affect phase time durations and vehicle queuing lengths on the controlling approach as well as queuing lengths on the metered approach. This study showed that, based on the study for the Old Belair Road roundabout in Adelaide, South Australia, the total queue length (controlling + metered) will be minimized when the detector is relocated at 209 meters from the roundabout stop line, giving longer phase green times and resulting in decreased intersection queuing lengths.

The implementation of residential distributed generation (DG) in South America has shown significant growth in the last decade, driven by increased research on photovoltaics and renewable energy sources. Regulatory policies and business models have been crucial in fostering the adoption of DG in the region, with residential self-supply being the most receptive sector for implementing the concept. This article presents a literature review on DG as applied to residential self-supply in South America by comprehensively analyzing documents published between 2013 and 2023, applying the PRISMA methodology. In total, 37 literature resources have been systematically selected and reviewed to contribute to the identification of trends and developments in the field of DG in the residential sector, as well as highlighting areas that require further research and attention from stakeholders, including policymakers, investors, technology providers and consumers in the South American context.

This study proposes a methodology for identifying time intervals in which time-of-use (ToU) energy tariffs can be set. This is achieved by analyzing the variability in electric power demand and esti-mating the potential for demand flexibility. The proposed methodology is as follows: first, data preprocessing is performed, focusing on the organization and cleaning of individual consumption records. Subsequently, the data are processed and classified by using consumption variability analysis and clustering techniques. Then, representative clusters are selected and time intervals are analyzed to identify periods of high electric power consumption variability. This methodology was tested with real data from smart meters in the Colombian electrical system, in which time intervals with potential for settinh ToU tariffs were ultimately identified. This work promotes the implementation of demand response strategies that enhance sustainability and facilitate the transition to a more resilient energy landscape both nationally and internationally. The findings are expected to contribute to the formulation of tariff schemes that encourage con-scious changes in electric energy consumption patterns.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Rooftop solar (RTS) projects have the potential to contribute to climate change mitigation and sustainable development objectives. In India, grid-connected RTS capacity has been targeted at 40 GW by the end of the year 2022 however, the installed capacity is limited to 8.2 GW only. As a result, the country missed its 2022 target of installing 100 GW of solar power capacity, largely due to inadequate uptake of RTS. The prevailing practices of RTS implementation is observed to be complex, repetitive, tedious, and time-consuming for potential consumers and there is a lack of coordination among implementing agencies. Therefore, even with vast potential, supportive measures, dedicated policies, and regulations the penetration of RTS systems is far below their respective potential. The introduction of information technology (IT) intervention in the RTS sector would integrate key stakeholders at a single platform so as to reduce the administrative burden of implementing agencies, optimization of processing time, handle multiple consumers simultaneously, and connect consumers with authentic vendors, etc. This would help them to understand and perform their shared roles and responsibilities and enhance the RTS implementation across the state. In this study, the scope for IT interventions in the existing RTS implementation process of the Odisha Renewable Energy Development Agency (OREDA) has been assessed and a simplistic approach has been developed for the execution of the RTS projects in relatively lesser time with the least human interface as well as resources. This approach has been successfully demonstrated with OREDA and a cumulative capacity of around 5 MWp (individual project of 1-2 kWp) residential grid-connected RTS projects implemented through the web platform. Currently, other state nodal agencies are also adopting the model for RTS execution and consumer proliferation through IT interventions.

The smart grid system, an improvised form of the traditional grid, is considered a critical cyber-physical system. Due to its complex combination of smart and legacy technologies, this technology is characterized by a wide range of features such as full duplex communication, advanced metering infrastructure, remote monitoring, and control. However, despite this system’s substantial environmental and socio-economic impact on modern life, it poses severe security vulnerabilities due to its integration and interconnected and interdependent cyber-physical components. Based on the rapid development of cyber-physical systems (CPS), academics and industries have investigated relevant techniques to enhance and strengthen the security measures of the SG system. The intrusion detection system is a countermeasure, a powerful safeguard against various cyber-attacks and threats. The contribution of the IDSs to the SG paradigm is examined in this study. A comprehensive review has been presented in this study, highlighting different techniques, basic ideas, and analyses. Besides discussing the contemporary pertinent research studies, the shortcomings of the existing IDS for the SG system are also identified with a recommendation for future research direction.

We applied evolutionary game theory to extend a resource constrained security game model for confidentiality attacks in an Advanced Metering Infrastructure (AMI), which is a component of IoT-enabled Smart Grids. The AMI is modelled as a tree structure where each node aggregates the information of its children before encrypting it and passing it on to its parent. As a part of the model, we developed a discretization scheme for solving the replicator equations. The aim of this work is to explore the space of possible behaviours of attackers and to develop a framework where the AMI nodes adaptively select the most profitable strategies. Using this model, we simulated the evolution of a population of attackers and defenders on various cases resembling the real life implementation of AMI. We discuss in depth how to enhance security in AMI using evolutionary game theory either by a priori analysis or as a tool to run dynamic and adaptive infrastructure defence.

A fluid power industry powering the agricultural machinery faces big challenges nowadays. An issue of energy saving has become important due to increasing fuel costs and more stringent emissions regulations impacting vehicle development. A recent study conducted by the U.S. Department of Energy shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications and create innovative solutions. To increase energy efficiency of fluid power systems reduction of throttling losses and potential energy recovery strategies are needed. Aim of this work is to present classification of current energy saving architectures and aid the development of new techniques for mobile fluid power machines.

Life in the modern century is heavily reliant on an enormous amount of electricity consumption as technology has become the most integral part of daily life. In this context, smart grid systems play a pivotal role to maintain the uninterrupted power supply which needs to be monitored in a timely fashion to keep track of the electric consumers’ usage pattern. The smart meter is the one of smart applications of the smart grid that collects huge amounts of consumer load data on a daily basis which has become a focus for various researchers and analyzers to study load characterization. In this paper, an approach has been proposed to recognize the energy consumption patterns among diverse types of consumers ranging from residential to industrial levels. This approach is worth considering not only for load pattern recognition but also for involving customers in different events such as demand response or peak shaving. In such a way, this analytical mechanism certainly assists in reducing power wastage and saving costs. The proposed methodology is based on a two-fold clustering algorithm with the use of state-of-the-art technology, machine learning. The primary goal is to classify electric customers' data collected from smart meters. Then, analyzing the classified results with an aim to predict power consumption patterns for the customers in the future and making the right energy policy that will benefit both the grid operator and consumers as well.

Power systems have been going through a barrage of transformations due to the recent developments in the field, such as deregulation and restructuring of the electric power supply chain, the proliferation of distributed generation (DG), and advancements in information and communications technologies. These have significantly impacted the approach to the planning, design, and operation of active distribution networks or systems. Due to this constant change, the system has become more complex to plan, maintain, and control. In this paper, the benefits, and challenges of active distribution systems relative to traditional passive and active distribution systems are evaluated and investigated while the management and operational characteristics of demand-side resources in Active Distribution Systems (ADS) are studied. In a typical ADS, there exist several vulnerabilities and threats that eventually pose a challenge in the control and automation of substations. These vulnerabilities and threats are reviewed, and potential mitigation measures are suggested. Also in this paper, the communication technologies, and their implementation in terms of control and automation capabilities in active distribution networks are also studied. From this work, it is concluded that communication technologies play an integral role in the realization of a more active distribution networks and that the internet of energy (IoE) is a major player in ADS in the reduction of faults due to human error, fast responses, and improving the stability of power supply. Cyber threats are also and will still be a continuous challenge in smart metering technologies and in substation automation systems (SAS) which will require frequent evaluation and mitigation measures so as not to prevent the power supply system from collapsing.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

Smart grid software interconnects multiple Engineering disciplines (power systems, communication, software and hardware technology, instrumentation, big data, etc.). The software architecture is an evolving concept in smart grid systems in which systematic architecture development is a challenging process. The architecture has to realize the complex legacy power grid systems and cope up with current Information and Communication Technologies (ICT). The distributed generation in smart grid environment expects the software architecture to be distributed and to enable local control. Smart grid architecture should also be modular, flexible and adaptable to technology upgrades. In this paper, the authors have made a comprehensive review on architecture for smart grids. An in depth analysis of layered and agent based architectures is presented and compared under various domains.