Ninety percent of the existing building stock in Europe was built before 1990. These buildings are in urgent need for a significant improvement of energy-efficiency through renovation. Regrettably, so far only five percent of renovation projects have been able to yield energy-saving at deep renovation level. State-of-the-art renovation solutions are available, but costly and lengthy renovation processes and incomprehensible technical complexities hinder the achievement of a wide impact at a European scale. This paper presents research on Plug-and-Play (PnP) technologies supported by Building Information Modelling (BIM) to provide affordable, interchangeable and quick-installation solutions to overcome the main barriers of building deep renovation.

At present European buildings typically consume two to five times more energy than predicted at the design stage. An important cause of this performance gap is the discrepancies between the design specification and the As-Built condition. Such discrepancies are mainly due to the gaps in knowhow between design, production and construction professionals. Design is more and more contained into a virtual environment and loses touch with the physical production and construction sites. As the construction sector enters the Industry 4.0 era, Building Information Modelling (BIM) based Mixed Reality can intertwine virtual and real worlds to bridge the knowhow gaps.

The construction industry is responsible for 40 to 45% of primary energy consumption in Europe alone. Therefore, it is essential to find new materials with a lower environmental impact in order to attain sustainable housing. This study aims to determine and compare the environmental impact of two clay samples forming a basis for the manufacture of traditional brick, a standard material in building construction; traditional red clay brick and a brick based on clay mixed with a biological ingredient. The samples of fired clay were manufactured at the laboratory scale, the results being valid exclusively as indicators for the extrapolation of the analysis to other studies. The results of the environmental impact of these formulations have been examined through an evaluation of life-cycle analysis (LCA), observing that the incorporation of biological pore forming agents led to a decrease of around 15 to 20% of all impact categories studied. Thus, the suitability of using biological-based additives in clay bricks was confirmed both for their constructive characteristics (lighter material) and increased energy efficiency (better thermal insulation) considering the environmental point of view.

We explores the relational, dynamic elements of Complex Buildings, a type of architecture designed to incubate uses, located in urban areas with high housing density. The uses of Complex Buildings concern different elements, including the network of agents using or managing them, the environment, and the activities and functions that take place occasionally, temporarily or permanently. Data was gathered through ethnographic research lasting 6 months and a chronotopian approach was used to describe time and space. We analyzed and discussed the interaction of the elements of Complex Buildings through a cellular automaton model, a computational method that simulates the growth of complex systems. It was used here to generate patterns that suggest configurations of uses that can optimize management and therefore increase economic and social capital. The cellular automaton model was also used to develop an abstraction of the Centquatre, a public cultural center in Paris. This center is a good example of a Complex Building, being based on a public-private partnership and having an architectural configuration designed to host a wide range of art, social and productive activities. The building includes a large central space used as an urban public area open to different types of people. The importance of this case study lies in its capacity to produce economic value by combining different uses, and also by welcoming different people to the public space. Regarding the building as a living organism, the cellular automaton model reveals the determinant nature of the concepts of configuration, compatibility of uses and economic value generated by the presence of people. We argue that this approach makes it possible to show that the space-time design and public space dimensions are determinant factors in Complex Buildings.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

The article reveals distinctive features of the interaction between architectural and structural solutions for the design of tall buildings as well as spotlights the most distinctive cases of expression. In the contemporary world, interaction is turning into the antithesis of the formerly dominant utilitarian attitude and standardization of tall buildings architectural solutions. Meanwhile, the search for rational structural solutions leads to new possibilities of architectural expression. This necessitates the transformation of a structural solution and its adaptation to the need of a modern architect to be exceptional and noticed. Interaction covers the current as well as retrospective and perspective periods. SWOT analysis was used by the authors of the article to assess the interaction between architectural and structural solutions in tall buildings design, select the most important criteria that could be used searching for rational architectural and structural solutions in future by applying multi-criteria decision making methods.

Although the European reports highlight an increase in community-acquired Legionnaires’ disease cases, the risk of Legionella spp. in private houses is underestimated. In Pisa (Italy) we performed a three-year survey on Legionella presence in 121 buildings with an independent hot water production (IB); 64 buildings with a central hot water production (CB); and 35 buildings with a solar thermal system for hot water production (TB). From all the 220 buildings Legionella spp. was researched in two hot water samples collected either at the recirculation point or at on the first floor and on the last floor, while the potable water quality was analyzed in three cold water samples collected at the inlet from the aqueduct network, at the exit from the autoclave, and at the most remove remote? tap. Legionella pneumophila sg1, Legionella pneumophila sg2-16 and not-pneumophila Legionella species were detected in 26% of the hot water networks, mostly in CB and TB. In these buildings we detected correlations between the presence of Legionella and the total chlorine concentration decrease or/and the increase of the temperature. Cold water resulted free from microbiological hazards, with the exception of Serratia liquefaciens and Enterobacter cloacae isolated at the exit from two different autoclaves. We observed an increase in total microbial counts at 22 and 37°C between the samples collected at the most remote taps compared to the ones collected at the inlet from the aqueduct. The study highlights a condition of potential risk for susceptible categories of population and supports the need for measures of risk assessment and control.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.