Interaction of Fine Aerosol Droplets with Contaminant Particles

1. Introduction

The issue of interaction of aerosol particles with air pollutants and methods of air purification from these pollutants remains relevant, as evidenced by a number of publications in recent years. The work [1] provides a modern review of the global problem of indoor air quality. Review [2] describes in detail the impact of indoor air pollution on human health, systematizes the sources of these pollutants and sometimes non-obvious consequences. Recent studies have discovered new, previously unconsidered effects of pollutants on human health. For example, work [3] studies the effect of PM2.5 aerosol particles on the spread of the influenza virus in the body. It was found that the association of the virus with solid particles facilitates its delivery to the lower respiratory tract and further spread.

Works [4,5] consider and discuss air purification methods, including physicochemical technologies (e.g., filtration, adsorption, UV photocatalytic oxidation, ultraviolet disinfection and ionization) and biological technologies (e.g., plant-based purification methods and microalgae-based methods). The works devoted to the purification of indoor air from pollutants do not mention the method of spraying water mist (or other liquid aerosol) to absorb and remove contaminants from the air. Such a method, however, would be useful, especially in disinfection and purification of air in hospitals, or for the elimination of the consequences of emergency emissions in industrial premises.

The interaction of specially sprayed aerosol with radioactive aerosol generated by leaks or accidents at nuclear power plants has been studied the most [6]. Many researchers have studied the characteristics of the aerosol removal process using a spray system. The mechanisms of removal of harmful aerosols were described in the classical works of Fuchs (1965) [7]. An improved model of particle removal from the air as a result of droplet interception is given in the work of Lee (1980) [8]. The mechanism of particle removal due to Brownian diffusion was studied by Postma (Postma et al., 1975) [9] and Jung (Jung and Lee, 1998) [10] – taking into account the circulation of liquid inside the droplet. A combination of mechanisms of particle removal from the air was studied in the work of Lee and Liu (1980) [11]. These classical models of single droplet behavior allowed us to consider the efficiency of aerosol removal by spraying a special aerosol (multiple droplets). One of the first and relatively simple models of particle removal from air by spraying an aerosol was developed by Postma (Postma et al., 1978) [12]. Later, such models began to take into account the agglomeration of droplets during interaction with pollutant particles, for example, the work of Powers (Powers and Burson, 1993) [13]. The work [14] discusses in detail the effect of droplet agglomeration on the removal of radioactive aerosol formed as a result of the accident. In particular, it was found that the effect of droplet agglomeration on the efficiency of aerosol removal is not linear. It depends on the specific droplet size distribution. It was found that droplet agglomeration has the greatest effect on the removal of finely dispersed contaminant aerosols, especially with a particle diameter of less than 1.5 μm. The effect of electrostatic charging of droplets of the capturing aerosol, as well as wettability of contaminant particles on the efficiency of capturing is investigated in [15]. It was found that charged droplets of sprayed aerosol provide almost complete removal of all particles due to the electrostatic effect, regardless of wettability/size, even for particles with a diameter of less than 10 μm. In this case, wettability of particles is important when removing them with neutral sprays (hydrophilic particles are captured better than hydrophobic ones). An interesting result of this work was the established fact that dynamic agglomeration of particles during the capturing process does not have a noticeable effect on the result of contaminant removal, but the initial size of the droplets of the sprayed aerosol is very important.

The mechanisms of contaminant removal by neutrally charged aerosol spraying are primarily inertial collision, interception, and Brownian diffusion (Ardon-Dryer et al., 2015) [16], with diffusiophoresis and thermophoresis (Santachiara et al., 2013) [17] also considered. The particle size of the contaminant is a key parameter determining their kinetic behavior. For particles larger than 10 μm, gravitational sedimentation plays a significant role, while smaller particles can remain in the air for a long time, and therefore are the most difficult to remove. For the removal of aerosol particles smaller than 0.1 μm, the main mechanism is Brownian diffusion, while for aerosol particles larger than 1 μm, the most effective removal method is inertial sedimentation. However, in the transition range for particles with a diameter of 0.1 to 1 µm (Greenfield, 1957) [18], these mechanisms demonstrate significantly lower efficiency.

It is known that particles with sizes less than 10 µm, especially less than 2.5 µm, are the most dangerous for human health, regardless of their chemical composition [19]. Therefore, it is necessary to study the behavior of contaminant particles with sizes less than 10 µm and the possibility of removing precisely such particles from the air using a specially sprayed aerosol.

One of the main conditions for the efficiency of contaminant removal using aerosol droplets is high aerosol dispersion. Such droplets do not settle for a long time and remain in the air, collecting harmful substances, have a large specific surface area, increasing the efficiency of interaction with substances in the air. On the other hand, aerosol generation should occur with a sufficiently high productivity. The development of methods for cleaning indoor air from contaminants using a specially sprayed aerosol has so far been limited by the shortcomings of the means for creating such an aerosol. Recently, methods of highly productive spraying of fine aerosol based on the use of ultrasound have appeared [20]. They make it possible to create an aerosol with a characteristic droplet size of about 30-40 μm, which remain in the air for a long time collecting pollutants. The behavior of these droplets and their interaction with contaminants has its own characteristics and differences, from, for example, the behavior of droplets with characteristic sizes significantly exceeding the size of contaminant particles (100 μm and more), which were usually considered by researchers before. The dominant mechanisms of interaction between fine droplets and contaminant particles differ from those characteristic of larger droplets. These mechanisms and differences, as well as the efficiency of contaminant capture by fine aerosol droplets (less than 50 μm in diameter) have not yet been studied.

The aim of the work is a theoretical study of the mechanisms of interaction of aerosol droplets with a characteristic size of 30–50 μm with contaminants in the air, as well as the efficiency of trapping fine particles of contaminants by aerosol droplets. It is necessary to identify the leading mechanisms of interaction and determine the conditions for maximum efficiency of air purification from harmful particles.

2. Mathematical Description of the Interaction of Aerosol Droplets and Contaminant Particles

2.1. Statement of the Problem

We will consider an aerosol with a characteristic droplet diameter d_d ~ 30-50 μm, specially sprayed in a room volume where there is already an aerosol of pollutant particles with a diameter d_p from 100 nm to 10 μm. The pollutant can be represented by various phase compositions, can have an electric charge (which is typical, for example, for bacteria), can be characterized as hydrophobic or hydrophilic. The behavior of aerosol droplets with the specified characteristic size is fundamentally different from the behavior of droplets with a diameter of about 100 μm or more, for example, sprayed by a nozzle. Such spraying is used to precipitate radioactive particles and has been well studied both theoretically and experimentally. What is the difference between an aerosol with droplets of 30-50 μm?

• Such droplets quickly (< 1 s) slow down in the air at a short distance (< 10 cm) from the spray nozzle. Then the droplets spread in space as a result of convective diffusion [21].
• The relative velocity of droplets and particles is determined not by the velocity of the droplet leaving the spray nozzle (as for droplets larger than 100 μm), but primarily by the difference in the velocity of gravitational settling.
• Droplets settle under the action of gravity much more slowly than larger ones (the settling velocity is proportional to the square of the particle diameter). Therefore, they remain in the air for a long time and interact with contaminant particles all this time.
• Such droplets have a relatively large specific surface area, compared to larger droplets. Also, with the same mass of sprayed aerosol, the numerical concentration of smaller droplets will be significantly higher. It is the numerical concentration of droplets and their total surface area that determines the efficiency of capturing contaminant particles as a result of coagulation and adsorption.

2.2. Mechanisms of Capture of Contaminant Particles by Aerosol Droplets Depending on the Size of Droplets and Particles

In the problem of interaction between droplets and small contaminant particles, the following mechanisms are usually considered:

• Inertial collision (large particles deviate from the streamlines and collide with the droplet). Relatively large aerosol particles (e.g., droplets > 30 μm in diameter) settle under the action of gravity and collide with smaller contaminant particles, capturing them along the way.
• Diffusion deposition (small particles, such as viruses, move due to Brownian or convective diffusion). Both types of particles (aerosol droplets and contaminants) are subject to chaotic thermal motions, which increases the probability of collisions.
• Interception (particles follow the streamlines and “graze” the droplet if they are close enough). When a contaminant particle moves along the air flow line and gets close enough to an aerosol droplet, it can be “captured” by adhesion on the droplet surface. This occurs if the streamline is at a distance less than or equal to the particle radius (d_p/2) from the droplet surface.
• Electrostatic attraction (if the particles are charged). Viral envelopes (e.g., capsids or lipid membranes) and bacterial cell walls are often negatively charged due to the presence of ionized groups (e.g., carboxyl or phosphate) on their surface. The magnitude of the charge depends on the pH of the environment, but under typical air conditions (pH neutral or slightly acidic), the charge remains negative. For example, for viruses such as SARS-CoV-2, the surface charge is estimated to be in the range of -10 to -50 mV (ζ potential). Aerosol droplets are usually neutral in the absence of external influences (such as an electric field or ionization). However, a neutral particle can become polarized in the presence of a charged particle, which creates an attraction. An induced electrostatic interaction occurs between the negatively charged particle (virus/bacteria) and the neutral droplet. This occurs due to the polarization of the droplet: the negative charge of the contaminant repels the electrons in the droplet, creating a local positive charge on its surface near the particle.

The capture efficiency is defined as the ratio of the number of particles actually captured by the droplet to the number of particles that could theoretically collide with it if they moved in a straight line in the projection of its cross section. The key parameters for the listed capture mechanisms are as follows.

2.2.1. Inertial Capture

The efficiency is determined by the Stokes number Stk: $\mathrm{Stk}={\displaystyle \frac{{\rho }_p{d}_p^{2}U}{18\mu d_d}},$

where ρ_p is the density of the contaminant particle, d_p is the diameter of the contaminant particle, U is the relative velocity between the droplet and the particle, $U={\displaystyle \frac{g}{18\mu }}\left(d_d^2{\rho }_d-d_p^2{\rho }_p\right),$ ρ_d is the droplet density, g is the acceleration of gravity, μ is the viscosity of air, d_d is the droplet diameter.

The dependence of the capture efficiency for three ranges of the Stokes number is known [21,22,23]:

$${\eta }_{iner}=\left\{\begin{array}{l}0,\mathrm{Stk}\le 0.083\\ 8.57{\left({\displaystyle \frac{\mathrm{Stk}}{\mathrm{Stk}+0.5}}\right)}^2(\mathrm{Stk}-0.083),0.083<\mathrm{Stk}<0.2\\ {\left({\displaystyle \frac{\mathrm{Stk}}{\mathrm{Stk}+0.5}}\right)}^2,\mathrm{Stk}\ge 0.2\end{array}\right.$$

2.2.2. Diffusion Capture

The capture efficiency depends on the Peclet number Pe [24]: η_dif ~ 4 Pe^−2/3,

Pe = U d_d / k_D, where $k_D={\displaystyle \frac{k_{b}T}{3\pi \mu d_p}}$is the diffusion coefficient of the particle, k_b (m³/s) is the Boltzmann constant, T is the temperature.

This formula is suitable for the case of low droplet velocities, very low Reynolds number values, and this is the case we are considering.

2.2.2. Interception

The interception efficiency depends on the ratio of the particle and droplet sizes R = d_p / d_d [7,25]: η_inter ≈ 3 / 2 R².

This approximate formula does not take into account the viscosity of the droplets, their volume concentration, but is suitable for a relatively low volume concentration of droplets and in the case when the viscosity of the liquid is much greater than the viscosity of the gas medium (which is true for water droplets in air).

2.2.3. Electrostatic Capture [21,26]

For a charged particle with charge q and a neutral drop, the attractive force in the approximation of a point charge and a polarizable sphere is given by: $F_{electr}={\displaystyle \frac{q^2{d}_d^3}{32\pi {\epsilon }_0{r}^4}}{\displaystyle \frac{\epsilon -1}{\epsilon +2}},$

where r is the distance between the center of the drop and the particle, ε₀ is the electric constant, ε is the dielectric constant of the drop (for water ε ≈ 80), (ε − 1)/(ε + 2) is the polarization factor (for water close to 1).

This force decreases as 1/r⁴, which makes it significant only at short distances. The electrostatic contribution to the capture efficiency depends on the dimensionless parameter N_E , which characterizes the ratio of the electrostatic force to the resistance of the medium: $N_E={\displaystyle \frac{q^2}{3{\pi }^2{\epsilon }_0\mu U{d}_d^2}},$η_elec ~ N_E.

Viruses and bacteria can carry an electric charge due to the ionization of surface chemical groups (e.g., amino acids in viral capsid proteins or peptide glycan in bacterial cell walls) or adsorption of ions from the environment (e.g., in a humid environment). The charge of such a particle can be proportional to the diameter (if it is distributed volumetrically) or to the surface area (for a surface charge). Most often, the charge depends on the surface area of the particle, ~ d_p² (surface charge), so we will adopt this dependence in the calculations. Then η_elec ~ N_E = q₀d_p², where q₀ is the proportionality coefficient. According to experimental data, the charge of a virus with a diameter of 20-200 nm is q = 10–100 e (where e is the electron charge) [27]. For bacteria with a diameter of 0.5-10 μm, the charge is q = 10⁴–10⁶ e [28]. From this, the parameter q₀ can be estimated.

The efficiency of particle capture by a droplet is described by the capture coefficient η, which depends on the interaction mechanism. For the droplet-contaminant system, the overall capture coefficient can be written as a combination of different mechanisms, taking into account their independence:

η = 1 – (1 – η_iner)(1– η_dif )(1– η_inter)(1 – η_elec)

2.3. Dynamics of the Decrease in the Mass of Contaminant Particles when They Are Captured by Aerosol Droplets

When assessing the efficiency of contaminant removal using aerosol droplets, an important issue is the reduction of the mass of contaminant particles in the air. How long will it take to clean the air of harmful particles? How completely can particles be removed from the air using an aerosol?

The capture efficiency η determines the fraction of particles that collide with a droplet from the flow passing through its cross-section. For a single droplet with a diameter d_d, the effective capture area is proportional to the cross-sectional area of the droplet: $S_{eff}=\eta {\displaystyle \frac{\pi d_d^2}{4}}.$ Particle flow captured by a droplet: $J_d=n_{p}U{S}_{eff}=n_{p}U\eta {\displaystyle \frac{\pi d_d^2}{4}},$ where n_p is the concentration of contaminant particles.

We will assume that with a constant uniform supply (spraying in the room) of aerosol, a quasi-stationary concentration of droplets nd will be established in the volume of the room, determined by the arrival of droplets as a result of spraying and the loss as a result of settling on the walls, gravitational settling and evaporation. Smaller particles of the contaminant in the air will settle much more slowly and will not undergo evaporation (for solid particles). Then the decrease in their number will occur precisely as a result of the capture of aerosol by droplets. The rate of change in the concentration of particles is proportional to the concentration of droplets and the flow of particles captured by the droplet:

$${\displaystyle \frac{d{n}_p}{dt}}=-n_d{J}_d=-n_d{n}_{p}U\eta {\displaystyle \frac{\pi d_d^2}{4}}.$$

The capture constant will be denoted as $k_{capt}=n_{d}U\eta {\displaystyle \frac{\pi d_d^2}{4}}.$

Then the change in the number of contaminant particles in the air will be expressed as follows:

$$n_p(t)=n_p(0)\cdot \exp (-k_{capt}t).$$

It is necessary to determine the mass of contaminant particles captured by the aerosol. The relative mass of captured contaminant particles depending on time:

$${\displaystyle \frac{m_p(t)}{m_p(0)}}=1-\exp (-k_{capt}t).$$

We will also express the capture constant through the mass concentration of droplets m_d: $k_{capt}={\displaystyle \frac{3}{2}}{\displaystyle \frac{m_d}{d_d{\rho }_d}}U\eta .$

All contaminant particles will be completely removed from the air in time of $t\to \infty .$ In the problem, we can determine the characteristic time (time constant) of the particle capture process – t_capt = 1 / k_capt. This is the time during which or the mass of contaminant particles in the air will decrease by e times. This value can be used to judge how quickly aerosol droplets will collect particles from the air under these conditions.

2.4. Correction for Small Particles

For relatively large (compared to the free path of molecules) particles and droplets, the continuous medium approximation is valid, and the Stokes equations for the resistance and motion of particles are valid. The possibility of using this approximation is determined by the Knudsen number: $\mathrm{Kn}={\displaystyle \frac{2\lambda }{d_p}},$ where λ is the mean free path of air molecules (~ 68 nm under normal conditions).

For particles whose diameter is much larger than λ, the condition Kn << 1 is satisfied. But for particles of 10 – 100 nm (e.g., viruses), Kn ~ 1 and larger, and the continuous medium approximation begins to break down. Then the diffusion coefficient for such small particles is determined with the Cunningham correction: $k_{D1}=k_D{C}_K,$ where $C_K=\left(1+1.257\mathrm{Kn}+0.4\exp (-1.1/\mathrm{Kn})\right).$The particle sedimentation velocity will also be determined with this correction, then the relative sedimentation velocity: $U={\displaystyle \frac{g}{18\mu }}\left(d_d^2{\rho }_d-d_p^2{\rho }_p{C}_K\right).$

3. Results and Discussion

3.1. Model Calculations

We perform calculations for various contaminants and various conditions, according to the model proposed above. As contaminant particles, we will take soot particles with a density of ρ_p = 2000 kg/m³. First, we will consider how the contaminant particle size for different droplet sizes affects the components of the particle capture efficiency by droplets (Figure 1).

The efficiency of capture due to diffusion is only noticeable for the smallest particles, with a diameter of less than 0.5 μm, then with increasing particle size the contribution of the interception mechanism becomes increasingly significant, and then, starting from approximately 4 μm and more, the inertial capture mechanism “comes in”. Inertial capture is more significant for larger droplets, which is understandable – their cross-sectional area is larger. A small kink in the curve of the inertial capture efficiency is associated with the transition from empirical formulas for different ranges of particle diameters.

Figure 2 shows the curves for the capture time calculated for different droplet sizes, depending on the size of the contaminant particles (the mass concentration of droplets in the calculations is 0.1 g/m³).

The curves in Figure 2 have an extremum associated with the Greenfield gap. Small particles (less than 0.5 μm in diameter), for which the diffusion capture mechanism is significant, are quickly absorbed by aerosol droplets. Relatively large particles (more than 2-3 μm in diameter) are quickly captured by aerosol droplets due to inertia and, in part, the interception mechanism. In the range from 0.5 to 2.5 μm, the capture efficiency due to diffusion is already low, and due to inertia it is still low, so the capture time is maximum here. At the same time, the maximum capture time in this gap is less for droplets of smaller diameter, for example, for droplets of 30 μm in diameter the maximum time will be 32 minutes, for droplets of 50 μm – 54 minutes.

We now consider how droplet size for different particle sizes affects the components of droplet capture efficiency (Figure 3).

As can be seen from Figure 3a, for small particles the capture is determined exclusively by diffusion, for particles larger than 2.4 μm diffusion plays almost no role, but the interception mechanism plays an important role (Figure 3c). For particles of about 5 μm and larger, the inertial capture by droplets increasingly plays the main role, and the capture efficiency becomes increasingly higher. Inertial capture is most important for larger droplets compared to smaller ones (Figure 3d). In the most problematic region of particle diameters of about 0.5-1 μm, inertial capture does not play a role, and the efficiency of diffusion capture is also already low. The interception mechanism begins to have an effect, but the total efficiency due to interception and diffusion turns out to be minimal (and the capture time is maximum).

Figure 4 shows the dependence of the capture time on the droplet diameter for different particle diameters.

For small particles, in this calculation with a diameter of less than 2.4 μm, the dependence of the capture time on the droplet diameter is linear – it increases with the droplet size. For large particles (here – with a diameter of more than 5 μm), a slight decrease in the capture time is observed in the calculation. For particles of 0.1 and 2.4 μm, the capture time is practically the same in the entire range of droplet sizes. These are the sizes that limit the Greenfield gap. The particle diameter of 0.9 μm corresponds to the maximum capture time for all droplet sizes, but with an increase in the droplet diameter, this time also increases linearly. This suggests that for the most difficult to capture particles from the Greenfield gap zone, the smaller the size of the aerosol droplets, the sooner they will be captured. But this is not true for larger particles – for them, larger aerosol droplets give a slightly better result (the capture time is slightly lower, as in curves 5 and 8 in Figure 4).

The calculations above did not take into account the possible charge of the particles. However, if the particles are viruses or bacteria, or have a triboelectric charge, then this capture mechanism must also be taken into account for small particles.

Now we will consider the effect of the contaminant particle size for different droplet sizes on the components of the particle capture efficiency by droplets, including the electrostatic mechanism (Figure 5). In the calculation, q₀ = 0.0001 C/m² is assumed.

Figure 5 does not show the inertial component of capture, since it is negligibly small for such small particles. On the other hand, it is the electrostatic component of the capture efficiency that plays a major role, starting with particle sizes of about 0.5-0.7 µm, where the diffusion component (the intersection of the blue and green curves on the graphs) begins to yield to this component. The component associated with interception makes an insignificant contribution.

Figure 6 shows the curves for the capture time calculated for different droplet sizes, depending on the contaminant particle size, taking into account the electrostatic component and the Cunningham correction.

The capture time of contaminated particles is shorter than that of uncharged particles (Figure 2), while the maximum of the curves corresponding to the most problematic particle sizes is shifted to the left (towards smaller particles) compared to the case of no charge. The dependence on the droplet size is more pronounced - the smaller the droplets, the faster the particle capture occurs, especially in the problematic area. Thus, spraying finer aerosol droplets is an advantage in removing small particles, especially those with an electrostatic charge – such as viruses and bacteria.

3.2. Comparison with Experiment

The paper [29] presents experimental data on the deposition of submicron zinc oxide particles by aerosol droplets of various diameters. The Sauter diameter of the aerosol droplets used in the work is 162 μm (the modal diameter is 80 μm). Although we consider droplets of a smaller size, we performed a calculation for droplets with a diameter of 80 μm according to the presented model for the capture time of various fractions of submicron particles in order to compare with the results of the paper [29]. The capture time of particles of a certain fraction was obtained from the table in Figure 8 of the paper [29], where the time when the number of particles of a given diameter decreased by e times was taken as such time. The comparison results are shown in Figure 7. A mass concentration of droplets of 0.15 g/m³ was adopted in the calculation.

Figure 7. Particle capture time depending on their diameter, comparison with the experiment from work [29] with the calculation according to the above model: points – experiment, curve – calculation.

Figure 7. Particle capture time depending on their diameter, comparison with the experiment from work [29] with the calculation according to the above model: points – experiment, curve – calculation.

Figure 8. Particle capture time depending on their diameter for particles of different densities, water aerosol with a droplet diameter of 40 µm.

Figure 8. Particle capture time depending on their diameter for particles of different densities, water aerosol with a droplet diameter of 40 µm.

As can be seen from the graph, the calculation based on the given model describes the experimental results well. The most difficult to capture particles are in the range from 0.1 to 1.5 μm. But particles with a diameter of more than 2 μm are captured by aerosol droplets in a few seconds, given a sufficient droplet concentration. In this calculation, the particle density is much higher than for soot (ρ_p = 5680 kg/m³), the aerosol droplets are larger, and the droplet concentration is higher than in the above model calculations. Therefore, the relative velocity of the particles is also higher, and the inertial component of the capture efficiency is significant even for small particles with a diameter of up to 3 μm.

The capture time is inversely proportional to the mass concentration of aerosol droplets, so the higher the droplet concentration, the shorter the time for removing contaminant particles. The effect of particle density on the capture time is shown in Figure 8. It shows the results of calculating the capture time for particles of different sizes and densities by water aerosol droplets with a diameter of 40 μm.

All other things being equal, the density of particles affects the time of their capture by droplets only in the transition region (the transition from the dominant mechanism of diffusion capture for small particles to the dominance of the inertial capture mechanism). The transition to inertial capture begins for heavier particles already at 2 µm, and for lighter particles – at 3-5 µm. In this size range, heavy particles are removed faster than lighter ones. But for particle sizes over 5 µm, there is practically no difference in the capture time. Therefore, the effect of particle density on the process of their removal can be considered insignificant.

4. Conclusions

The paper considers the problem of removing finely dispersed contaminant particles with a characteristic size from 100 nm to 10 μm from indoor air using a fine aerosol sprayed in the air (droplet diameter 30-50 μm). Removing precisely such finely dispersed particles from the air, including viruses and bacteria, and PM2.5, PM10 particles, is the most difficult. Aerosol spraying for removing finely dispersed radioactive particles is used in practice, but coarser aerosols are used. The emergence of new aerosol spraying methods that combine high productivity and high droplet dispersion opens up new possibilities for using this method of removing particles in a wider technological range. While the interaction of relatively large droplets (more than 100 μm in diameter) with contaminant particles has been studied theoretically and experimentally, the interaction of droplets 30-50 μm in diameter with finely dispersed particles, which has its own characteristics, has not yet been studied. We have considered in detail the mechanisms of such interaction, including diffusion, inertial, interception, electrostatic (for charged particles). A mathematical description of capture corresponding to the case under consideration is proposed. The model is verified by comparison with experiment (the results are given in [29]).

As a measure of the capture efficiency, in addition to the efficiency coefficient, we propose to use the characteristic capture time, when the mass of particles in the air decreases by e times compared to the initial one. It was found that in the Greenfield gap, that is, in the range of particle diameters where no capture mechanism is sufficiently effective and the capture time is maximum, the best result is shown by aerosol droplets of the minimum size (in our calculations, these are droplets with a diameter of 30 μm). The capture time of charged particles (i.e., viruses and bacteria) is especially reduced by droplets with a diameter of 30 μm compared to larger droplets. The higher the aerosol dispersion, the more effective the removal of highly dispersed contaminant particles from the air in the most difficult range of sizes of these particles. The effect of particle density on the capture efficiency in the problem under consideration turned out to be insignificant. It is shown that the capture time is inversely proportional to the mass concentration of aerosol droplets. This means that the higher the mass concentration and the higher the dispersion of the sprayed aerosol, the higher the rate of removal of contaminant particles. The calculations performed and the results obtained create the prerequisites for the development and widespread use of a method for removing highly dispersed contaminant particles, including viruses and bacteria, from indoor air by spraying fine aerosol droplets.