Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

Nanomaterials based on metal oxides (MexOy) are employed as catalysts and/or sorbents in processes undergoing conditions in supercritical water (scH2O), the “green” reaction medium used to obtain energy relevant products. Their properties are greatly affected by the synthesis method used to produce the active MexOy. Moreover, in order to maintain their performance, it is more practical and cost-effective to use supported MexOy nanoparticles. Within this context, the present work deals with the preparation of carbon-supported ZnO and CuO composites by an innovative method based on impregnation under scH2O conditions. Metal oxides were impregnated on a carbon (C) support using a continuous flow tubular reactor. The results show that impregnation in scH2O is a promising approach for the preparation of ZnO/C and CuO/C composite materials. This one-step synthesis method, in a continuous flow, uses neither seed layer nor mineralizer, and it needs substantially lower preparation times than the conventional impregnation methods.

Shear deflection effects are traditionally neglected in most structural system identification methods. Unfortunately, this assumption might lead to significant errors in some structures, like deep beams. Although some inverse analysis methods based on the stiffness matrix method including shear deformation effects have been presented in the literature, none of these methods is able to deal with actual rotations in their formulations. Recently, the observability techniques, one of the first methods for the inverse analysis of structures included the shear effects into the system of equations. In this approach, the effects of shear rotation are neglected. When actual rotations on site are used to estimate the mechanical properties in the inverse analysis, it can result in serious errors in the observed properties. This characteristic might be especially problematic in structures such as deep beams where only rotations can be measured. To solve this problem and increase the observability techniques' applicability, this paper proposes a new approach to include shear rotations into the inverse analysis by observability techniques. This modification is based on the introduction of a new iterative process. To illustrate the applicability and potential of the proposed method, the inverse analysis of several examples of growing complexity is presented.

Composite polymolecular separation membranes were prepared by combining multi-branched ZIF-L with high porosity electrospinning nanofibers PI. Meanwhile, PDA and PEI were introduced into the membrane in order to improve its adhesion. The new membrane is so called “PI@PDA@PEI/ZIF-L-4” composite membrane; compared with PI@PDA@PEI/ZIF-8 composite membrane, the new membrane’s filtration rates for heavy metal ions such as Cd2+, Cr3+ and Pb2+ were increased by 7.0%, 6.6% and 9.3%, respectively. Furthermore, the new membrane has a permeability up to 1,140.0 L·m−2·h−1·bar−1, and were presenting a very stable performances after four repeated uses. The separation mechanism of PI@PDA@PEI/ZIF-L composite membranes was further analyzed in order to provide a base support for producing separation membranes with high barrier rate and high flux.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

The use of tungsten fiber-reinforced tungsten composites (Wf/W) has been demonstrated to significantly enhance the mechanical properties of tungsten (W) by incorporating W-fibers into the W-matrix. However, prior research has been restricted by the usage of single fiber-based textile fabrics, consisting of 150 µm warp and 50 µm weft filaments, with limited homogeneity, reproducibility, and mechanical properties in bulk structures due to the rigidity of the 150 µm fibers. To overcome this limitation, two novel textile preforms were developed utilizing radial braided yarns with 7 core- and 16 sleeve filaments (R.B. 16+7) as the warp material. In this study, bulk composites of two different fabric types were produced via a layer-by-layer CVD-process, utilizing single 50 µm filaments (type 1) and R.B. 16+7 yarns (type 2) as weft materials. The produced composites were sectioned into KLST-type specimen based on DIN EN ISO 179-1:2000 using electrical discharge machining (EDM), and subjected to three-point bending tests. Both composites demonstrated enhanced mechanical properties with pseudo-ductile behavior at room temperature and endured over 10,000 load cycles between 50-90 % of their respective maximum load without sample fracture. Composites based on fabric type 1 demonstrated superior manufacturing performance and mechanical properties, a high relative average density (>97 %), and high fiber volume fraction (14-17 %). Furthermore, a novel approach to predict the fatigue behavior of the material under cyclic loading was developed based on the high reproducibility of the mechanical properties of type 1, providing a new benchmark for upscaling endeavors.

Magnesium is one of the lightest structural metal used in different industrial sector and many works are present in literature about the study of its reinforcement by fillers addition. Basalt fibres are natural fillers with good mechanical properties, excellent resistance to high temperature and lower cost than carbon fibres. For these aspects, in the last years they are increasingly used in the production of composite materials with polymeric matrices. However, very few information are presents in literature about the use of basalt fibres as reinforcement in metal matrix composite materials. It is well known that the impregnation of fibres reinforcement affects the mechanical behavior of composites materials. The aim of this study is to investigate the impregnation and the behavior of basalt fibres in a magnesium alloy composite material manufactured by a centrifugal casting technique.

Several challenges stand in the way of production of Metal Matrix Composites (MMCs) such as higher processing temperatures, particulate mixing, particulate-matrix interface bonding issues and ability to process into desired geometrical shapes. Although there are many literatures showing composites with single particulate reinforcements, the studies on composites with multiple reinforcing agents (hybrid composites) are found to be limited. Development of a hybrid particulate composite with optimized mechanical and tribological properties is very significant to suit modern engineering applications. In this study, Al-Si hypereutectic alloy (A390) is used as the matrix and Silicon Carbide (SiC) and Graphite (Gr) and Molybdenum di-Sulphide (MoS₂) are used as particulates. Particulate volume (wt%) is varied and sample test castings are made using squeeze casting process through stir casting processing route. The evaluation of mechanical properties indicates that presence of both the hard phase (SiC) and the soft phase has distinct effect on the properties of Hybrid Composite. Composite samples were characterized to understand the performance and to meet the tribological applications. Fractography study indicated an intra-granular brittle fracture for hybrid composites. Wear study shows that Hybrid MMCs has better tribological performance compared to that of A390 alloy.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

The main purpose of the work was to determine the powder composition and properties of iron-based sinters used as a matrix in metallic diamond tools. The FeCuSnNi sinters obtained from a mixture of commercial powders were used for research. The material was subjected to milling in a ball mill and sinter have been performed with the hot-pressing technique in a graphite mold. The physical and mechanical properties of the sinters were tested. The investigations of obtained sinters concerned density, porosity, hardness, oxygen content, static tensile test and analysis of microstructure. The static tensile test was carried out with the use of a universal testing machine UTS-100. The study of the microstructure of sinters was performed using the JSM-7100F scanning electron microscope. The sinters are characterized by a high coefficient of thermal expansion and good mechanical properties. The FeCuSnNi sinter revealed a complex phase structure. Spot chemical analysis revealed the presence of Fe solution, Cu solution and the presence of iron oxides oxides. Nickel atoms were present throughout the sinter volume. The obtained results indicate that the presented material can be used as a matrix of a diamond-metal composite in diamond tools for the processing of natural stones and building materials.

In response to the growing demand for high-strength and high-toughness materials in industries like aerospace and automobiles, there is a need for metal matrix composites (MMCs) that can simultaneously enhance strength and toughness. This paper focuses on the design configurations of MMCs, which include both the configurations resulting from reinforcements and the inherent heterogeneity of the matrix itself. The mechanical properties of MMCs are influenced by factors such as reinforcement content, shape, size, and spatial distribution within the composite architecture. Among them, Aluminum matrix composites (AMCs) are particularly significant in aerospace, electronics, and electric vehicles due to their potential for weight reduction and enhanced performance. However, the challenge lies in the inverse relationship between strength and toughness, hindering the widespread utilization and large-scale development of MMCs. The design configuration of composites plays a critical role in achieving concurrent improvements in strength and toughness. This review explores the advantages of toughness, toughening mechanisms, reinforcement distribution characteristics, and structural parameters in the design of composite architectures. Drawing inspiration from biological composites like bone, the development of synthetic composites with homogeneous structural designs provides insights into attaining exceptional strength and toughness in lightweight engineering structures. Additionally, understanding fracture behavior and toughening mechanisms in heterogeneous nanostructures is vital for advancing the field of metal matrix composites. Summarily, the design of composite architectures holds tremendous potential for tailoring AMCs with outstanding strength and toughness, addressing the requirements of lightweight engineering structures in various industries.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is key parameter in the construction of the sensing (macro)molecular architectures. In this work, multi-walled carbon nanotubes (in short, CNTs) were deposited on diazonium-modified flexible ITO electrodes prior to electropolymerization of pyrrole. This three step process, including diazonium electroreduction, deposition of CNTs and electropolymerization, provided adhesively bonded polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM) which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 182.6 nm to 274.8, 35.65.9 and 17520.1 after 1, 5 and 10 of electropolymerization of pyrrole. The PPy/CNT/NH2-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10-83×10-7 mol.L-1 Pb(II) concentration range and the detection limit was 2.9×10-9 mol.L-1 at S/N=3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, density functional theory (DFT) was employed to calculate the EGTA-metal ion interaction energy which was found to be -374.6 and -116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications.

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (> 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

Due to the difficult metallurgical conditions during production, advanced processing techniques are required to produce functionally graded metal matrix composites. In this study, we explored a novel approach by using a combination of two different methods to produce Functionally Graded 7075 Al / SiCp composites. First process was direct semi-solid stirring that was used to prevent particle agglomeration, brittle reaction products, floating or settling of the reinforcements and poor wettability for the production of SiCp (wt. 5-20%) reinforced aluminum matrix composites. In the direct semi-solid mixing process, the matrix material remains in a semi-solid state until the reinforcement addition process is completed. The second novel process was sequential squeeze casting to provide liquid diffusion between two composite layers that were used to produce functionally graded aluminum matrix composite. The microstructure and interlayer zones were characterized by using optical microscopy and scanning electron microscopy. The resulting functionally graded material was subjected to spectrometer analyses, density measurements, and metallographic examinations in order to determine the characteristics of its layers and interfacial zones, as well as to assess the formation of the graded structure. The results obtained from this research provide the potential to use this new combined manufacturing method, which is relatively inexpensive, efficient and easily applicable, in order to produce functionally graded SiCp reinforced aluminum composites.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

Various iron oxides have been proven to be promising anode materials for metal-ion batteries due to their natural abundance, high theoretical capacity, ease of preparation, and environmental friendliness. However, the synthesis of iron oxide-based composites requires complex approaches, especially when it comes to composites with intrinsically conductive polymers. In this work we propose a one-step microplasma synthesis of a polyaniline-coated urchin-like FeOOH nanoparticles (FeOOH/PANI) for application as anode in lithium-ion batteries. The material shows excellent electrochemical characteristics, providing initial capacity of ca. 1600 mA∙h∙g−1 at 0.05 A∙g−1 and 900 mA∙g−1 at 1.2 A∙g−1. Further cycling lead to capacity decrease to 150 mA∙h∙g−1 by the 60th cycles, followed by a recovery that maintained the capacity at 767 mA∙h∙g−1 after 2000 cycles at 1.2 A∙g−1 and restored full initial capacity of 1600 mA∙h∙g−1 at low current density of 0.05 A∙g−1. Electrochemical milling of the material caused such interesting behavior of the material, and we confirmed this phenomenon by a combination of physico-chemical and electrochemical techniques. The anodes also exhibit high performance in a full cell with NMC532. NMC532//FeOOH/PANI full cell provided energy density of 224 Wh∙kg−1 which is comparable to the reference cell with graphite anode (264 Wh∙kg−1).

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex > organic-matter–clay mineral complex > iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

In this paper, we deduce explicit formulas to evaluate the determinants of nonsymmetrical structure Toeplitz Bohemians by two determinants of specific Hessenberg Toeplitz matrices, which are linear combinations in terms of determinants of specific Hessenberg Toeplitz matrices. We get some new results very di¤erent from [Massimiliano Fasi, Gian Maria Negri Porzio, Determinants of normalized upper Hessenberg matrices, Electronic Journal of Linear Algebra, Volume 36, pp. 352-366, June 2020].

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

In the present study, the efficiency of a biomimetic approach by coating demineralized bone matrix (DBM) amorphous calcium phosphate (DBM+CaP), including its combination with serum albumin (DBM+CaP+BSA), was investigated. The intact structure of DBM promotes the transformation of amorphous calcium phosphate (CaP) into DPCD with a characteristic plate shape and particle size of 5–35 µm. The inclusion of BSA in the coating resulted in a better and more uniform distribution of CaP on the surface of DBM trabeculae. MG63 cells showed that both the obtained forms of CaP and its complex with BSA did not exhibit cytotoxicity up to a concentration of 10 mg/ml in vitro. Ectopic (subcutaneous) implantation in rats revealed pronounced biocompatibility, as well as strong osteoconductive, osteoinductive, and osteogenic effects for both DBM+CaP and DBM+CaP+BSA, but more pronounced effects for DBM+CaP+BSA. In addition, for the DBM+CaP+BSA samples, a pronounced full physiological intrafibrillar biomineralization and proangiogenic effect with the formation of bone-morrow-like niches, accompanied by pronounced processes of intramedullary hematopoiesis, indicating a powerful osteogenic effect of this composite have been achieved.

In this note we construct explicit complex and real matrix representations for the generators of real Clifford algebra $C\ell_{p,q}$. The representation is based on Pauli matrices and has an elegant structure similar to the fractal geometry. We find two classes of representation, the normal representation and exceptional one. The normal representation is a large class of representation which can only be expanded into $4m+1$ dimension, but the exceptional representation can be expanded as generators of the next period. In the cases $p+q=4m$, the representation is unique in equivalent sense. These results are helpful for both theoretical analysis and practical calculation. The generators of Clifford algebra are the faithful basis of $p+q$ dimensional Minkowski space-time or Riemann space, and Clifford algebra converts the complicated relations in geometry into simple and concise algebraic operations, so the Riemann geometry expressed in Clifford algebra will be much simple and clear.

Inorganic chemistry has contributed to the progress of human civilization in several different ways. Its activities at the interface with other scientific disciplines has led to emergence of several new fields like organometallic chemistry, bio-inorganic chemistry, solid-state chemistry, environmental chemistry, etc. In the past few decades, it has made inroads in yet another dimension of immense relevance, i.e. nano-science and –technology. In this assay an attempt has been made to present an overview of utility of inorganic and organometallic compounds as precursors for the synthesis of nano-materials with reference to catalysis and materials science. Applications of metal nanoparticles (NPs) and metal chalcogenide NPs, generated through molecular precursor route, in catalysis have been discussed. Synthesis of ternary and quaternary metal chalcogenide nano-materials by molecular precursor route has been reviewed.

In this study, we prove the norm separating property for the composition of Cesàro 1 and Gamma matrices with their transpose. As a result, we compute the ℓp-norms of six classes of operators that commute with the infinite Hilbert operators. Additionally, we find the norm of 3 Hilbert’s commutants on some well-known sequence spaces.

A complex square matrix $A$ is said to be Hermitian if $A= A^{\ast}$, the conjugate transpose of $A$. The topic of the present note is concerned with the characterization of Hermitian matrix. In this note, the we show that each of the two triple matrix product equalities $AA^{\ast}A = A^{\ast}AA^{\ast}$ and $A^3 = AA^{\ast}A$ implies that $A$ is Hermitian by means of decompositions and determinants of matrices, which are named the two-sided removal and cancellation laws associated with Hermitian matrix, respectively. We also present several general removal and cancellation laws as the extensions of the preceding two facts about Hermitian matrix.

One of matrix equalities composed of multiple products of matrices and their generalized inverses is given by $A_1B_1^{-}A_2B_2^{-} \cdots A_kB_k^{-}A_{k+1}= A$ where $A_1$, $B_1$, $A_2$, $B_2$, $\ldots$, $A_k$, $B_k$, $A_{k+1}$, and $A$ are given matrices of appropriate sizes, and $B_1^{-}$, $B_2^{-}$, $\cdots$, $B_k^{-}$ are generalized inverses of matrices. The cases for $k = 1, 2$ and their special forms were properly approached in the theory of generalized inverses of matrices. In this note, the author presents an algebraic procedure to derive explicit necessary and sufficient conditions for the equality with $k = 3$ to always hold using certain rank equalities for the block matrices constructed by the given matrices, and then mention a key step of extending the previous work to a general situation.

The present paper discusses a study of a class of Charlier matrix polynomials and its generalized analogue. Certain generating matrix functions, recurrence matrix relations, matrix differential equation, summation formulas and many new results have been discussed for these matrix polynomials. Weisner's group theoretic method is used to obtain matrix generating relations for Charlier matrix polynomials and the details of this method were given in this paper. Finally, we will discuss only briefly the procedure followed.

Though the cancer research community has used mouse xenografts for decades more than zebrafish xenografts, zebrafish have much to offer: they are cheap, easy to work with, and the embryonic model is relatively easy to use in high-throughput assays. Zebrafish can be imaged live, allowing us to observe cellular and molecular processes in vivo in real time. Opponents dismiss the zebrafish model due to the evolutionary distance between zebrafish and humans, as compared to mice, but proponents argue for the zebrafish xenograft’s superiority to cell culture systems and its advantages in imaging. This review places the zebrafish xenograft in the context of current views on cancer and gives an overview of how several aspects of this evolutionary disease can be addressed in the zebrafish model. Zebrafish are missing homologs of some human proteins and (of particular interest) several members of the matrix metalloproteinase (MMP) family of proteases, which are known for their importance in tumour biology. This review draws attention to the implicit evolutionary experiment taking place when the molecular ecology of the xenograft host is significantly different than that of the donor.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

In this paper we have studied some properties for determinant-calculating for cubic-matrix of order 2 and order 3. These properties are analogous to some properties for determinants of square matrix we have proved and noted that these properties also are applicable (or not in some details) on this concept for cubic-matrix of orders 2 and 3. All results in this paper, are presented in detail during the theorem proofs.

In this paper, we derive the distribution of eigenvalues for a 2×2 random confusion matrix stemming from a machine learning (ML) evaluation problem. Additionally, we present the distributions of both the matrix’s trace and the difference between the two traces of random confusion matrices. We also illustrate the application of these derived distributions in calculating the superiority probability of four baseline ML models.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

Iyer Markoulakis Helmholtz Hamiltonian mechanics formalisms mathematically modeled physics with vortex rotational fields acting with gradient fields, typically in zero-point microblackhole general fields. Here, Helmholtz metrics have been gaged to Coulombic Hilbert metrics, representing Gilbertian and Amperian natures of electromagnetic fields out of the mechanical fields from Helmholtz Hamiltonian mechanics. This ansatz general gaging helps to properly isolate field effects – mechanical, electric, magnetic components within the analytical processes. Vacuum gravitational fields and the flavor Higgs-Boson matter inertial gravitational fields have been thus quantified extending to stringmetrics constructs matrix showing charge asymmetry gage metrics, having the power to analyze dark energy superluminal phase, dark matter luminal phase, and light matter subluminal phase. Interpreting particle physics gage matrix pointing to Dirac seas electrons, monopoles with positrons, electron-positron annihilation leading to energy production, relativistic energy generating matter, and both monopoles – vacuum and compressed out of vortex Helmholtz decomposition fields have been interpolated. Quantum ASTROPHYSICS gage metrix posits superluminal profile of signals velocity generating electron-positron chain like “curdling” action that is consistent with physics literature reporting nature electron photon observed oscillatory fields configurations. This helps proposing creation of neutrino antineutrino pair orthogonal to electron positron “curdling” planes, that may lead to formation of protonic hydrogen of stars or orthogonally muon. These aspects will explain receding or fast expanding universe with dark matter in terms of flavor metrics versus gage associating metrics flavor. Additional interpretations of virtual gravitational dipoles that have gravitational charge of opposite signs, reported per physics literature at Planck dimensions, that may originate at the center of supermassive blackhole. On the other hands, vacuum monopoles occur probably at infinity with cosmos extent.

In this paper, we define Tetranacci and Tetranacci-Lucas matrix sequences and investigate their properties.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

Novel Ca3(BTC)2 metal-organic frameworks with different sizes and shapes constructed by Ca2+ and trimesic acid as metal center and ligands respectively were synthesized by a surfactant-assisted method. The relationship between the quantity of surfactant and the particle morphology of the product have been further studied. The samples were characterized by scanning electron microscope, powder X-ray diffraction and Inductively coupled plasma mass spectrometry. The results indicated that the size and shape of Ca3(BTC)2 could be regulated by changing the quantity of surfactant. Rod- and sheet-like Ca3(BTC)2 MOFs have been readily availabled. The removal kinetics of heavy metals of Pb(II) were also studied by rod-like Ca3(BTC)2. The results showed that as-synthesized Ca3(BTC)2 could effectively remove heavy metals of Pb(II) from the sewage.

Dimers and oligomers of alkenes represent a category of compounds that are in great demand for diverse industrial sectors. Among the developing synthetic methods, the catalysis of alkene dimerization and oligomerization using transition metal salts and complexes is of undoubted interest for practical application. This approach demonstrates substantial potential, offering not only elevated reaction rates but also precise control over the chemo-, regio-, and stereoselectivity of the reactions. In this review, we discuss the data on catalytic systems for alkene dimerization and oligomerization. Our focus lies in the analysis of how the activity and chemoselectivity of these catalytic systems are influenced by various factors, such as the nature of the transition metal, the ligand environment, the activator, and substrate structure. Notably, the review particularly discusses the reaction mechanisms, encompassing metal complex activation, structural and dynamic features, and the reactivity of hydride intermediates, which serve as potential catalytically active centers in alkene dimerization and oligomerization.

Herein, a novel cavity design of racetrack integrated circular cavity established on metal-insulator-metal (MIM) waveguide is suggested for refractive index sensing application. Over the past few years, we have witnessed several unique cavity designs to improve the sensing performance of the plasmonic sensors created on the MIM waveguide. The optimized cavity design can provide the best sensing performance. In this work, we have numerically analyzed the device design by utilizing the finite element method (FEM). The small variations in the geometric parameter of the device can bring a significant shift in the sensitivity and FOM of the device. The best sensitivity and FOM of the anticipated device are 1400 nm/RIU and ~12.01, respectively. We believe that the sensor design analyzed in this work can be utilized in the on-chip detection of biochemical analytes.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Serum transferrin (sTf) plays a pivotal role in regulating iron biodistribution and homeostasis within the body. The molecular details of sTf Fe(III) binding, blood transport, and cellular delivery through transferrin receptor-mediated endocytosis are generally well-understood. Emerging interest exists in exploring sTf complexation of nonferric metals as it facilitates the therapeutic potential and toxicity of several of them. This review explores recent X-ray structural and physiologically relevant metal speciation studies to understand how sTf partakes in the bioactivity of key non-redox active hard Lewis acidic metals. It challenges preconceived notions of sTf structure function correlations that were based exclusively on the Fe(III) model by revealing distinct coordination modalities that nonferric metal ions can adopt and different modes of binding to metal-free and Fe(III)-bound sTf that can directly influence how they enter into cells and, ultimately, how they may impact human health. This knowledge informs on biomedical strategies to engineer sTf as a delivery vehicle for metal-based diagnostic and therapeutic agents in the cancer field. It is the intention of this work to open new avenues for characterizing the functionality and medical utility of nonferric-bound sTf and to expand the significance of this protein in the context of bioinorganic chemistry.

Parallel decompositions have proved to be powerful tools for the analysis and interpretation of the physical information provided by Mueller matrices experimentally obtained. In this work, the procedure for the so-called arbitrary decomposition of Mueller matrices is validated through its application to a set of representative experimentally determined Mueller matrices. The covariance and passivity criteria required for the physical realizability of the Mueller matrices involved in the parallel decompositions are integrated in the procedure, which ensures the physical consistency of the results presented.

One of the typical forms of linear matrix expressions (linear matrix-valued functions) is given by $A + B_1X_1C_1 + \cdots + B_kX_kC_k$, where $X_1, \ldots, X_k$ are independent variable matrices of appropriate sizes, which include almost all matrices with unknown entries as its special cases. The domain of the matrix expression is defined to be all possible values of the matrix expressions with respect to $X_1, \ldots, X_k$. I this article, we approach some problems on the relationships between the domains of two linear matrix expressions by means of the block matrix method (BMM), the matrix rank method (MRM), and the matrix equation method (MEM). As application, we discuss some topics on the relationships among general solutions of some linear matrix equations and their reduced equations.

It is shown that a Mueller quaternion can be formulated as a quaternion with matrix coefficients, and this Mueller quaternion transforms the Stokes quaternion for depolarizing process as well as for nondepolarizing process. Mueller quaternion keeps track of the phase acquired by the Stokes quaternion and, in general, quaternion states of optical media comprises all properties of Jones, Mueller-Jones and Mueller matrices.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

Using two metal insulated metal waveguides (MIM) and five resonator (a quadrilateral cavity and three rings with different dimensions), we design a plasmonic refractive index sensor. Using the time domain finite difference method, we examine and analyze the sensor performance (numerical analysis) and using the transmission line model method, we theoretically examine the performance of the sensor By summarizing these two methods and calculating the sensitivity coefficient S, quality coefficient Q and figure of merit (FOM), a plasmonic sensor with good performance is obtained. Using the supermods of the resonators, we will achieve a stable wavelength spectrum and a suitable and stable sensitivity coefficient spectrum. Challenges and changes that occur in different modes of this sensor will lead to a balanced and relatively good structure. This designed sensor can be useful in the development of integrated optical circuits.

In this paper, a plasmonic refractive index sensor based on metal insulated metal waveguide (MIM) with three rings and a resonant cavity is first proposed and numerically evaluated. Next, we add four teeth to the sensor structure. We study and simulate the resonant wavelengths and refractive index of resonators using the time difference finite difference method. Given that the sensor and the conduction characteristics of plasmonic waves are influenced by the structure parameters,Therefore, by changing the refractive index and changing the dimensions and coordinates of the cavity and rims, we can change the passage coefficient in the resonant modes and measure the sensor performance. As a result, we obtain the sensitivity coefficient, the figure of merit (FOM) and the quality factor Q of the sensor. We modulate the resonance wavelength FWHM using the generated modes and reach a sensitivity of 2166 nm / RIU. These plasmonic sensors with a simple framework and balanced performance and high optical resolution can be used to measure the refractive index in the medical, chemical and food industries.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Reverse order laws for generalized inverses of matrix products is a classic object of study in the theory of generalized inverses. One of the well-known reverse order laws for a matrix product $AB$ is $(AB)^{(i,\ldots,j)} = B^{(s_2,\ldots,t_2)}A^{(s_1,\ldots,t_1)}$, where $(\cdot)^{(i,\ldots,j)}$ denotes an $\{i,\ldots, j\}$-generalized inverse of matrix. Because $\{i,\ldots, j\}$-generalized inverse of a singular matrix is unique, the relationships between both sides of the reverse order law can be divided into four situations for consideration. This paper provides a thorough coverage of the reverse order laws for $\{i,\ldots, j\}$-generalized inverses of $AB$, from the development of background and preliminary tools to the collection of miscellaneous formulas and facts on the reverse order laws in one place with cogent introduction and references for further study. We begin with the introduction of a linear mixed model $y = AB\beta + A\gamma + \epsilon$ and the presentation of two least-squares methodologies to estimate the fixed parameter vector $\beta$ in the model, and the description of connections between the two types of least-squares estimators and the reverse order laws for generalized inverses of $AB$. We then prepare some valued matrix analysis tools, including a general theory on linear or nonlinear matrix identities, a group of expansion formulas for calculating ranks of block matrices, two groups of explicit formulas for calculating the maximum and minimum ranks of $B^{(s_2,\ldots,t_2)}A^{(s_1,\ldots,t_1)}$, as well as necessary and sufficient conditions for $B^{(s_2,\ldots,t_2)}A^{(s_1,\ldots,t_1)}$ to be invariant with respect to the choice of $B^{(s_2,\ldots,t_2)}A^{(s_1,\ldots,t_1)}$. We then present a unified approach to the 512 matrix set inclusion problems associated with the above reverse order laws for the eight commonly-used types of generalized inverses of $A$, $B$, and $AB$ through use of the definitions of generalized inverses, the block matrix method (BMM), the matrix rank method (MRM), the matrix equation method (MEM), and various algebraic calculations of matrices.

The new barrier mode in Apache Spark allows embedding distributed deep learning training as a Spark stage to simplify the distributed training workflow. In Spark, a task in a stage doesn’t depend on any other tasks in the same stage, and hence it can be scheduled independently. However, several algorithms require more sophisticated inter-task communications, similar to the MPI paradigm. By combining distributed message passing (using asynchronous network IO), OpenJDK’s new auto-vectorization and Spark’s barrier execution mode, we can add non-map/reduce based algorithms, such as Cannon’s distributed matrix multiplication to Spark. We document an efficient distributed matrix multiplication using Cannon’s algorithm, which improves significantly on the performance of the existing MLlib implementation. Used within a barrier task, the algorithm described herein results in an up to 24% performance increase on a 10,000x10,000 square matrix with a significantly lower memory footprint. Applications of efficient matrix multiplication include, among others, accelerating the training and implementation of deep convolutional neural network based workloads, and thus such efficient algorithms can play a ground-breaking role in faster, more efficient execution of even the most complicated machine learning tasks

Given several nonnegative matrices with a single pattern of allocation among their zero/nonzero elements, the average matrix should have the same pattern, too. This is the first tenet of the pattern-multiplicative average (PMA) concept, while the second one suggests the multiplicative (or geometric) nature of averaging. The original concept of PMA was motivated by the practice of matrix population models as a tool to assess the population viability from long-term monitoring data. The task has reduced to searching for an approximate solution to an overdetermined system of polynomial equations for unknown elements of the average matrix (G), hence to a nonlinear constrained minimization problem for the matrix norm. Former practical solutions faced certain technical problems, which required sophisticated algorithms but returned acceptable estimates. Fresh idea to use the eigenvalue approximation ensues also from the basic equation of averaging, which determines the exact value of λ1(G), the dominant eigenvalue of matrix G, too, and the corre-sponding eigenvector. These are bound by the well-known linear equations, which reduce the task to a standard problem of linear programing (LP). The LP approach is realized for 13 fixed-pattern matrices gained in a case study of Androsace albana, an alpine short-lived perennial, monitored on permanent plots during 14 years. A standard software routine reveals the unique exact solution, rather than an approximate one, to the PMA problem, which turns the LP approach into ‘’the best of versatile optimization tools”. The exact solution turns out to be peculiar in reaching zero bounds for certain nonnegative entries of G, which deserves a modified problem formulation separating the lower bounds from zero.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{F}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We show that the public, secret and channel keys become indistinguishable to the eavesdropper under matrix multiplication. Remarkably, for achieving a 512-bit security level, the public key is 1024 bits and the private key is 768 bits, making them the smallest keys among post-quantum key exchange algorithms. Also, we discuss how to achieve key authentication, interdomain certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{Z}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We claim that the unique eavesdropper's opportunity to get the secret/private key is by means of an exhaustive search which is equivalent to the unsorted database search problem. Furthermore, we show that the secret/private keys become indistinguishable to the eavesdropper. Remarkably, to achieve a 512-bit security level, the keys (public/private) are of the same size when matrix multiplication is done over a reduced 8-bit size modulo. Also, we discuss how to achieve key certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

Heparanase (HPSE) has been defined as a multitasking protein that exhibits a peculiar enzymatic activity towards HS chains but which simultaneously performs other non-enzymatic functions. Through its enzymatic activity, HPSE catalyzes the cutting of the side chains of heparan sulfate (HS) proteoglycans, thus contributing to the remodeling of the extracellular matrix and of the basal membranes. Furthermore, thanks to this activity, HPSE also promotes the release and diffusion of various HS-linked molecules as growth factors, cytokines and enzymes. In addition to being an enzyme HPSE has been shown to possess the ability to trigger different signaling pathways by interacting with transmembrane proteins. In normal tissue and in physiological conditions, HPSE exhibits only low levels of expression restricted only to keratinocytes, trophoblast, platelets and mast cells and leukocytes. On the contrary, in pathological conditions, such as in tumor progression and metastasis, inflammation and fibrosis, it is overexpressed. With this brief review, we intend to provide an update on current knowledge about the different role of HPSE protein exerted by its enzymatic and not-enzymatic activity.

Heparanase (HPSE) has been defined as a multitasking protein that exhibits a peculiar enzymatic activity towards HS chains but which simultaneously performs other non-enzymatic functions. Through its enzymatic activity, HPSE catalyzes the cutting of the side chains of heparan sulfate (HS) proteoglycans, thus contributing to the remodeling of the extracellular matrix and of the basal membranes. Furthermore, thanks to this activity, HPSE also promotes the release and diffusion of various HS-linked molecules as growth factors, cytokines and enzymes. In addition to being an enzyme HPSE has been shown to possess the ability to trigger different signaling pathways by interacting with transmembrane proteins. In normal tissue and in physiological conditions, HPSE exhibits only low levels of expression restricted only to keratinocytes, trophoblast, platelets and mast cells and leukocytes. On the contrary, in pathological conditions, such as in tumor progression and metastasis, inflammation and fibrosis, it is overexpressed. With this brief review, we intend to provide an update on current knowledge about the different role of HPSE protein exerted by its enzymatic and not-enzymatic activity.

Metals are particularly sensitive to some pollutant gases. Many museum showcases and store rooms present atmospheres that can corrode cultural heritage artefacts containing metals. Whilst numerous strategies have been reported to mitigate such situations, avoiding them is preferable. Several approaches to testing materials used in construction, fitting out or dressing are used. The relative merits and drawbacks will be discussed. Several parameters of the most widely used, the accelerated corrosion ‘Oddy’ test have been investigated. The influence of abrasive on subsequent corrosion of lead and copper coupons have been assessed. Quantification methods for tested coupons are reviewed. The influence of test duration and temperature were assessed through comparison with real life, long term experience of materials behaviour. Direct contact tests with the material tested touching the test material has been investigated. Several materials present in artefacts are known to potentially cause corrosion when enclosed with metals in other artefacts. A number of situations have been investigated with pollution and RH and some corrosion rate measurements. Ways to isolate artefacts or mitigate are explored and a decision support model has been developed.

This research was conducted to analyze the content of Fe, Cu, Cd, Cr, and Pb in several species of fish taken from three lakes that is closely to disposal of industrial waste in Indonesia. The fish samples were taken from three lakes, namely, Muara Angke, Weda, and Morowali. The samples from Morowali were analyzed in April 2019, those from Weda from November to December 2019, and those from Muara Angke in June 2018. All the samples were then analyzed at the chemistry laboratory of the Department of Chemistry, Faculty of Mathematics and Natural Science, University of Indonesia, and the Integrated Laboratory of IPB. The results showed that all types of fish from Morowali and Weda were no longer safe to consume because they contained Fe, Cu, Cd, and Cr exceeding the threshold of metal contamination. Meanwhile, all types of fish from Muara Angke, except for ayam-ayam, are still safe for consumption. The results of this study can be a source of information regarding metal content in fish and fish feed for safe consumption. Several studies have been done to determine the metal pollutants contained by fish. Given the high consumption rate of fish and the hazards of heavy metals on humans’ health, such research must be furthered

Gasca D herbal formulation is an antidiabetic medicine for the management of diabetes mellitus produced exclusively from natural ingredients. The level of some essential elements (Copper, chromium, Cobalt, Iron, Manganese, Nickel and zinc) and toxic (Cadmium, Arsenic, Mercury, and Lead) heavy metals were determined using microwave plasma-atomic emission spectrometry (MP-AES). The aim of this study is to evaluate the levels of essential and toxic heavy metals and also identify bioactive compounds present in Gasca D herbal formulation. The result shows no traces of Lead, Mercury, Zinc, Arsenic and Zinc, Iron was found to have highest concentration 67.16 + 7.5 µg/g and Cadmium lowest concentration 0.4 + 0.03µg/g. GC-MS analysis of Gasca D herbal formulation revealed the presence of 14 biologically active compounds which include N-Formyl-beta-alanine, Paromomycin, 3,4-Altrosan, Benzamide, 1,3,4-Thiadiazol-2-amine, Carbamodithioic acid, Carbonic acid, alpha-D-Glucopyranoside, Ethyl isocyanide, 2-Propanesulfinic acid, Propanamide, 2-Butenenitrile, Dicyclopropyl carbinol, Isoxazolidine, 1,5-Hexadiene 10-Azido-1-decanethiol. Conclusion: The result indicates that the mean levels of toxic metals in Gasca D herbal formulation were below WHO permissible levels. Gasca D herbal formulation also contains various bioactive compounds that can have various medicinal application which can be used for the treatment of various diseases.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

Among the five human senses, light, sound, and force perceived by eye, ear, and skin, respectively are physical actions, and therefore can be easily measured and expressed as objective, univocal, and simple digital data with physical quantity. However, taste and odor molecules perceived by tongue and nose are chemical actions, it has been difficult to express them as objective and univocal digital data, since no reference chemicals can be defined. Therefore, while the recording, saving, transmitting to remote locations, and replaying human visual, auditory, and tactile information as digital data in digital devices has been realized (this series of data flow is defined as DX (digital transformation) in this review), the DX of human taste and odor information is not yet in the realization stage. Particularly, since there are at least 400,000 types of odor molecules and an infinite number of complex odors that are mixtures of these molecules, it has been considered extremely difficult to realize "human olfactory DX" by converting all odors perceived by the human olfaction into digital data. In this review, we discuss the current status and future prospects of the development of "human olfactory DX," which we believe can be realized by utilizing odor sensors that employ the olfactory receptors (ORs) that support human olfaction as sensing molecules (i.e., human OR sensor).

Matrix multiplication is probably one of the most basic and important operations having a wide range of applications in studying Linear algebra. We will be primarily focused on reviewing different algorithms for the multiplication of two n×n matrices. The most Naive method has a complexity of O(n3) but interestingly, algorithms with better complexity have been achieved. We will get to see how the complexity can be improved further, occasionally giving a survey.

Cancer invasion through basement membranes represents the initial step of tumor dissemination and metastasis. However, little is known about how human cancer cells breach basement membranes. Here, we used a 3-dimensional in vitro invasion model consisting of cancer spheroids encapsulated by a basement membrane and embedded in 3D collagen gels to visualize the early events of cancer invasion by confocal microscopy and live-cell imaging. Human breast cancer cells generated large numbers of basement membrane perforations, or holes, of varying sizes that expanded over time during cell invasion. We used a wide variety of small molecule inhibitors to probe the mechanisms of basement membrane perforation and hole expansion. Protease inhibitor treatment (BB94), led to a 63% decrease in perforation size. After myosin II inhibition (blebbistatin), basement membrane perforation area decreased by only 15%. These treatments produced correspondingly decreased cellular breaching events. Interestingly, inhibition of actin polymerization dramatically decreased basement membrane perforation by 80% and blocked invasion. Our findings suggest that human cancer cells can primarily use proteolysis and actin polymerization to perforate the BM and to expand perforations for basement membrane breaching, with a relatively small contribution from myosin II contractility.

The cutting-edge photovoltaic cells are an indispensable part of the ongoing progress of earth-friendly plans for daily life energy consumption. However, the continuous electrical demand that extends to the night time requires a prior deployment of efficient real-time storage systems. In this regard, metal-air batteries have presented themselves as the most suitable candidates for solar energy storage, combining extra lightweight with higher power outputs and promises of longer life cycles. Scientific research over non-precious functional catalysts has always been the milestone and still contributing significantly to exploring new advanced materials and moderating the cost of both complementary technologies. Metal-organic frameworks (MOFs) derived functional materials have found their way to the application as storage and conversion materials, owing to their structural variety, porous advantages, as well as the tunability and high reactivity. In this review, we provide a detailed overview of the latest progress of MOF-based materials operating in metal-air batteries and photovoltaic cells.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

This document focuses attention on the fundamental solution of an autonomous linear retarded functional differential equation (RFDE) along with its supporting cast of actors: kernel matrix, characteristic matrix, resolvent matrix, and the Laplace transform. The fundamental solution is presented in a form of the convolutional powers of the kernel matrix in the manner of a convolutional exponential matrix function. The fundamental solution combined with a solution representation gives an exact expression in explicit form for the solution of a RFDE. Algebraic graph theory is applied to the RFDE in the form of a weighted loop-digraph to illuminate the system structure and system dynamics and to identify the strong and weak components. Examples are provided in the document to elucidate the behavior of the fundamental solution. The paper introduces fundamental solutions of other functional differential equations.

This note reconsiders a matrix equality $A_1A_2^{-}A_3A_4^{-}A_5 = A$ composed by six matrices of appropriate sizes, where $A_2^{-}$ and $A_4^{-}$ are generalized inverses of $A_2$ and $A_4$, respectively, and solves a selection of matrix set inclusion problems associated with various mixed reverse order laws for generalized inverses of products of two, three, and four matrices by means of this equality and its variations.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

Childhood glaucoma encompasses congenital and juvenile primary glaucoma, which are heterogeneous, uncommon, and irreversible optic neuropathies leading to visual impairment with poorly understood genetic basis. Our goal was to identify gene variants associated with these glaucoma types by assessing the mutational burden in 76 matrix metalloproteinase-related genes. We studied 101 childhood glaucoma patients with no identified monogenic alterations using next-generation sequencing. Gene expression was assessed through immunohistochemistry. Functional analysis of selected gene variants was conducted in cultured cells and in zebrafish. Patients presented a higher proportion of rare variants in four metalloproteinase-related genes, including CPAMD8 and ADAMTSL4, compared to controls. ADAMTSL4 protein expression was observed in the anterior segment of both the adult human and zebrafish larvae's eye, including tissues associated with glaucoma. In HEK-293T cells, expression of four ADAMTSL4 variants identified in this study showed that two variants (p.Arg774Trp and p.Arg98Trp) accumulated intracellularly, inducing endoplasmic reticulum stress. Additionally, overexpressing these ADAMTSL4 variants in zebrafish embryos confirmed partial loss-of-function effects for p.Ser719Leu and p.Arg1083His. Double heterozygous functional suppression of adamtsl4 and cpamd8 zebrafish orthologs resulted in reduced volume of both the anterior eye chamber and lens within the chamber, supporting a genetic interaction between these genes. Our findings suggest that accumulation of partial functional defects in matrix metalloproteinases-related genes may contribute to increased susceptibility to early-onset glaucoma and provide further evidence supporting the notion of a complex genetic inheritance pattern underlying the disease.

The extracellular matrix (ECM) provides structural support for tissues and regulatory signals for resident cells. ECM requires a careful balance between protein accumulation and degradation for homeostasis. Disruption of this balance can lead to pathological processes such as fibrosis in organs across the body. Post-translational crosslinking modifications to ECM proteins such as collagens alter ECM structure and function. Dysregulation of crosslinking enzymes as well as changes in crosslinking composition are prevalent in fibrosis. Because of the crucial roles that ECM crosslinking pathways play in disease, the enzymes that govern crosslinking events are being explored as therapeutic targets for fibrosis. Here we review in-depth the molecular mechanisms underlying ECM crosslinking, how ECM crosslinking contributes to fibrosis, and therapeutic strategies being explored to target ECM crosslinking in fibrosis to restore normal tissue structure and function.

This paper attempts to propose a Riemann spring model via an analogy between the Riemann Zeta function of a complex number and the elastic spring in series.

This paper attempts to extend the Riemann Zeta function of a complex number to a function of a matrix and/or a tensor $A$, namely $$\zeta (A)=\sum _{n=1}^{\infty} \frac{1}{n^{A}}= \sum _{n=1}^{\infty} \sum_{k=1}^n\lambda_k A^k$$ and inverse $$A=\sum _{n=1}^{\infty} \sum_{k=1}^n \mu(n)\lambda_k \zeta(A^k)$$ where $\mu(n)$ is the M\"obius function, $A$ is a complex matrix or tensor with any order, and $\lambda_k$ is eigenvalue of the matri/tensor $A$. This kind of calculations on the Riemann Zeta function has never been seen in the literature. Some examples are provided.

The aim of this paper is to show how the mathematical basis is used for a precise treatment of double-entry bookkeeping, which was firstly developed in the nineteenth century by Sir William Rowan Hamilton. This is done by using basic notions of matrix algebra with the roots to the idea of using ordered pairs. We also reveal how the complex numbers and the rationals (fractions) developed in a mainstream of accounting science and became a leading platform for the ongoing processes within the Industry 4.0. The paper concludes with the examples on how accounting operations can be represented by matrix equations with a result of the essential report generating. The author represents a mathematical model of accounting which is independent of the specific existential forms but is capable to undertake the form of any of them and thus has the prospect of being understood and accepted by specialists globally.

Matrix metalloproteases (MMPS) are a family of well-known enzymes which operate prevalently in the extracellular domain, where they fulfil the function of remodeling the extracellular matrix. Within the about 26 family members, encoded by 24 genes in humans, MMP-2 and MMP-9, have been regarded as the primary responsibility for the basement membrane and pericellular ECM rearrangement. In cases of infiltrating carcinomas, which arise from the epithelial tissues of a gland or of an internal organ, a marked alteration of the expression and the activity levels of both MMPs is known to occur. Present investigation represents the continuation and upgrading of our previous studies, now focusing on the occurrence and intensity levels of MMP-2 and -9, and their proteomic correlations, in a cohort of 80 breast cancer surgical tissues

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

Many authors proposed analytical methods for solving fully fuzzy Sylvester matrix equation (FFSME) based on Vec-operator and Kronecker product. However, these methods are restricted to nonnegative fuzzy numbers and cannot be extended to FFSME with near-zero fuzzy numbers. The main intention of this paper is to develop a new numerical method for solving FFSME with near-zero trapezoidal fuzzy numbers that provides a wider scope of trapezoidal fully fuzzy Sylvester matrix equation (TrFFSME) in scientific applications. This numerical method can solve the trapezoidal fully fuzzy Sylvester matrix equation with arbitrary coefficients and find all possible finite arbitrary solutions for the system. In order to obtain all possible fuzzy solutions, the TrFFSME is transferred to a system of non-linear equations based on newly developed arithmetic fuzzy multiplication between trapezoidal fuzzy numbers. The fuzzy solutions to the TrFFSME are obtained by developing a new two-stage algorithm. To illustrate the proposed method numerical example is solved.

In this paper we perform numerous numerical studies for the problem of low-rank matrix completion. We compare the Bayesian approaches and a recently introduced de-biased estimator which provides a useful way to build confidence intervals of interest. From a theoretical viewpoint, the de-biased estimator comes with a sharp minimax-optimal rate of estimation error whereas the Bayesian approach reaches this rate with an additional logarithmic factor. Our simulation studies show originally interesting results that the de-biased estimator is just as good as the Bayesian estimators. Moreover, Bayesian approaches are much more stable and can outperform the de-biased estimator in the case of small samples. However, we also find that the length of the confidence intervals revealed by the de-biased estimator for an entry is absolutely shorter than the length of the considered credible interval. These suggest further theoretical studies on the estimation error and the concentration for Bayesian methods as they are being quite limited up to present.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

In this paper, some mixed type bounds on the spectral radius $\rho(A\circ B)$ for the Hadamard product of two nonnegative matrices ($A$ and $B$) and the minimum eigenvalue $\tau(C\star D)$ of the Fan product of two $M$-matrices ($C$ and $D$) are researched. These bounds complement some corresponding results on the simple type bounds. In addition, a new lower bound on the minimum eigenvalue of the Fan product of several $M$-matrices is also presented: $$ \tau(A_{1}\star A_{2}\cdots\star A_{m})\geq \min_{1\leq i\leq n}\{\prod^{m}_{k=1}A_{k}(i,i)-\prod^{m}_{k=1}[A_{k}(i,i)^{P_{k}}-\tau(A_{k}^{(P_{k})})]^\frac{1}{P_{k}}\}, $$ where $A_{1},\ldots, A_{k}$ are $n\times n$ $M$-matrices and $P_{1},\ldots, P_{k}>0$ satisfy $\sum^{m}_{k=1}\frac{1}{P_{k}}\geq 1$. Some special cases of the above result and numerical examples show that this new bound improves some existing results.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

Pulmonary infections with Mycobacterium avium occur in susceptible individuals following exposure to the bacterium in the environment, where it often persists in biofilms. Many methods have been used to generate biofilms of M. avium, and it is unknown whether different approaches generate similar structures and cell phenotypes. To make a parallel comparison of in vitro biofilm ultrastructure, extracellular matrix (ECM) composition, and drug susceptibility of biofilm resident bacteria, we used two published methods to generate M. avium biofilms: four week incubation in M63 medium or 24 hour exposure to dithiothreitol (DTT). Scanning electron microscopy revealed differences in biofilm ultrastructure between the two methods, including variation in appearance of ECM materials and morphology of resident cells, while light microscopy and staining with calcofluor white indicated that both biofilms contained polysaccharides characteristic of cellulose. Measuring susceptibility of biofilms to degradation by enzymes suggested differences in structurally important ECM molecules, with DTT biofilms having important protein and, to a lesser extent, cellulose components, and M63 biofilms having moderate protein, cellulose, and DNA components. Both biofilms conferred resistance to the bactericidal effects of amikacin and clarithromycin, with resident cells being killed at >10-fold lower rates than planktonic cells at almost all concentrations. Though these comparisons indicate differences in biofilm responses by M. avium under differing conditions, they also suggest common features of biofilm formation including cellulose production and antimicrobial resistance.

We formulate a more straightforward, symmetry-based techniques in manually computing the determinant of any n×n matrix by revisiting Dodgson’s condensation method and strategically applying elementary row operations and the definition and properties of determinants. The result yields a more simplified mnemonical algorithm than the usual reduction by elementary row operations and co-factor expansion and with minimal terminal divisions performed compared to Dodgson’s internal divisions.