The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

This article presents an in-depth review of Virtual Power Plant (VPP), its organization in the energy system and its prospects in the face of the promising future of the increasing bidirectional complexity exposed in the current scenario. A new paradigm for the operations of modern power distribution and transmission systems requires greater grid flexibility that is accompanying an extensive change in the structure of electricity markets, the fruit of the development of the renewable industry and of the growing photovoltaic systems popularized, but in contrast due to the intermittent nature cause variable uncertainties in the power system. Innovative concepts like VPP are becoming a reality, establishing an efficient and effective mechanism. The objectives and components are described in a comprehensive way, and some of the most important are pointed out and presented in detail to contribute with a description of the energy systems and the implicit research needed for sustainability and resilience in the eminent energy scenario with this technology. In addition, the literature and studies of this technology already indicate a direction of this new tool as a promising solution to manage the uncertainties of the renewable energies.

Unmanned aerial vehicles serving as air base stations (UAV-BSs) are used in telecommunications, when the network is overloaded or unavailable, providing access to users on the ground. Due to its dynamics of providing access to networks in different altitudes, the electromagnetic signal of UAVs suffers losses along the path, thus facing several problems related to transmission, such as: attenuation, fading and distortion. In this work is proposed a 3D positioning strategy for UAVs, taking into account height, coverage radius and flight energy efficiency. Results show that the proposed algorithm is able to position the UAVs in suboptimal locations, providing network access for mobile users, maximizing the number of connected devices in the UAV-BS and saving energy, thus obtaining better performance than the approaches conventional.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Τhe building automation control is a crucial factor for improving buildings energy efficiency and management, as well as improving the electricity grid's reliability indices. This paper presents the methodology, describes the necessary technology requirements and presents the decentralized building automation novel algorithm for Efficient demand side management in a building. All these are applied in an experimental university microgrid and the results are presented in terms of energy saving in kWh, money in € and working hours.

The dark energy from virtual gravitons is consistent with observational data on supernova with the same accuracy as the CDM model. The fact that virtual gravitons are capable of producing of a de Sitter accelerated expansion of the FLRW universe was established in 2008 (see references). The combination of conformal non–invariance with zero rest mass of gravitons (unique properties of the gravitational field) leads to the appearance of graviton dark energy in a mater-dominated era. Тhis fact explains the relatively recent appearance of the dark energy and answers the question “Why now?”. The transition redshifts (where deceleration is replaced by acceleration) that follow from the graviton theory are consistent with model independent transition redshifts derived from observational data. Prospects for testing the GCDM model (the graviton model of dark energy where G stands for gravitons) and comparison with the CDM model are discussed.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

The paper is based on the research project P2Endure funded within the H2020-EE-2016-2017 call. The main aim of the research is to propose innovative solutions for deep renovation that are applicable and replicable for the widest range of building typologies, from public to residential and historic buildings. In this paper, the methodology adopted to perform the energy analyses and to verify the achievement of the expected targets in terms of savings is defined, based on a range of real case studies. The main aim is to promote a guideline for designers showing specific instruments to perform towards the attainment of the 60% threshold of the energy savings giving advice on how to further improve the energy performance of the buildings, basing on the overview of the energy analyses run for similar cases.

The ubiquitous problem of electrical energy waste is driven by human error, in which people regularly forget to turn off appliances when they leave a room, resulting in excessive consumption. The paper presents an energy-efficient TRIZ-inspired (EETRIZ) paradigm to automate consumer electronic devices in order to address this problem. Employing motion detection at entry and exit points, the system discerns room occupancy, effectively managing electrical appliances like lamps, fans, and air conditioners. The integration of theory of inventive problem solving (TRIZ) principles guides the ideation and design of an efficient switching mechanism. The system demonstrates that it is flexible by controlling multiple electronic consumer devices simultaneously. This paradigm can be used in a variety of environments, such as homes, offices, schools, and universities, and its goal is to reduce excessive energy use that results from human negligence. With an emphasis on economic viability and environmental impact, the proposed EETRIZ paradigm not only offers enhanced energy efficiency but also lays the groundwork for long-term sustainability practices, aligning with global efforts towards greener and smarter energy management. The proposed EETRIZ is implemented on C platform with support of MPLAB, Nuvoton 8051 Serie MCU Programming, GMPLibrary (GMP-5.1.1) and, Miracl Library. The proposed EETRIZ outperforms current state-of-the-art methods in terms of energy efficiency, cost-effectiveness, precision, and user-friendliness, according to hardware testing.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

In the last years, the Distribution Grid Operators (DGOs) assumed transition strategies of the distribution grids towards an active area associated with the "Smart Grids" concept. They are considering the use of Artificial Intelligence techniques, combined with advanced technologies and real-time remote communication solutions of the enormous data amounts, to develop smart solutions into the small size distribution grids, also called microgrids (μGs). These solutions will provide support for the DGOs to ensure an optimal operation of the technical infrastructure of the μGs. In this context, a bi-level methodology for solving the phase load balancing problem in the μGs with complex topologies and a high number of single-phase consumers, considering a clustering-based selection criterion of the consumers for placement of the switching devices, was proposed in the paper. A real μG from a rural area, with 114 consumers integrated into the Smart Metering System (SMS), belonging to the DGO from Romania, was considered in testing the proposed methodology. An implementation degree of 17.5%, corresponding to the phase load balancing equipment installed to only 20 consumers from the μG, led to a faster computational time with 43% and reducing the number of switching operations by 92% than in the case of a full implementation degree (100%). The performance indicators related to the unbalance factor and energy-saving used in the evaluation of the technical benefits highlighted the efficiency of the proposed methodology.

The sensor nodes have limited computation, sensing, communication capabilities and generally operated by batteries in a harsh atmosphere with non-replenish able power sources. These limitations force the sensor network subject to failure because most of the energy is spent on sensing, computing and data transmission. This paper introduces an Energy Efficient Clustering and Shortest-Path Routing Protocol (EECSRP) to assist Wireless Sensor Networks (WSNs) by (a) extending the lifespan of the network (b) effectively using the battery power (c) decreasing the network overhead and (d) ensuring a high packet transmission ratio with minimal delay. The delay time-based Cluster Head (CH) is elected based on the node degree, residual energy and Received Signal Strength (RSS) to accomplish the goal. Additionally, the RSS-based network partitioning is implemented to evaluate the gradient based on demand routing between source (sensing node) and destination (BS). Whenever the current CH residual energy goes under the threshold level, the proposed protocol performs the clustering process, reducing the exchange of control packets. However, the BS periodically gathers the data from every single CH which helps to reduce the collision and Medium Access Control (MAC) layer conflict. From the simulation results, it is the evident that the proposed protocol performance in terms of average end-to-end latency, packet delivery ratio, average energy consumption and control overhead is better than the well-known current protocols.

Cloud computing transformed IT organizations with its on-demand model, notably Infrastructure as a Service (IaaS). Cloud providers manage extensive physical devices, consuming substantial energy and bandwidth for data traffic during virtual machine deployment. Balancing energy and bandwidth are critical. This thesis presents BOHGOA integrated with ACO to optimize virtual machine placement in clouds, simultaneously considering bandwidth and energy. It yields Pareto-optimal solutions for this trade-off. Using CloudSim, BOHGOA outperformed GA, ACO, and FFD algorithms, reducing bandwidth consumption by 54.14%, 32.11%, 57.47% (240 VMs) and 38.12%, 22.76%, 47.05% (500 VMs) respectively. Additionally, it decreased physical machine energy usage by 37.70%, 34.01%, 40.14% (240 VMs) and 27.50%, 22.28%, 30.52% (500 VMs) respectively. These results underscore BOHGOA's effectiveness in optimizing cloud VM placement.

In this work, an energy-saving smart light controlling system has been proposed that can main-tain the desired intensity of light in a room automatically. Unlike the conventional light control system, the proposed system splits a large room into several zones and analyzes the light inten-sity of each zone; hence, the controlling unit adjusts the light intensity to the desired level. The main controlling unit consists of a light sensor, a motion sensor, a relay with a driver unit, an LCD display, etc. for controlling light efficiently to reduce the power waste. The sensors meas-ure the intensity of light, based on the standard light intensity data chart the controller units make a decision how many light bulbs are needed to be switched ON/OFF in a particular zone. Moreover, the system automatically switched-OFF all light bulbs when there is nobody in the room. Proteus design suite 8.0 is used to design and simulation of the proposed system. Moreo-ver, the PCB layout is designed using ExpressPCB version 7.5.0. The proposed system is capable of minimizing the power loss by up to 44% in comparison to the conventional light manage-ment system.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

Efficient train driving plays a vital role in reducing the overall energy consumption in the railway sector. An energy minimising control strategy can be computed using the framework given by optimal control theory, in particular the Pontryagin maximum principle. Our optimisation approach is based on an algorithm presented by Khmelnitsky that considers electric trains equipped with regenerative braking. A derivation of Khmelnitsky’s theory from a more general formulation of the maximum principle is given in this article, and a complete list of switching cases between different driving regimes has been included that is essential for practical application. A number of numerical examples are added to visualise the various switching cases. Energy consumption data from real-life operation of passenger trains are compared to the calculated energy minimum. In the presented study, the optimised strategy was able to save 37 percent of the average energy demand of the train in operation.

The optimization of the energy grid is a critical task for ensuring a sustainable and efficient energy future. Deep machine learning techniques have the potential to improve energy grid optimization by predicting energy demands and supplies, optimizing energy production and distribution, and detecting and preventing fraud. However, there are also several challenges associated with the use of deep machine learning in energy grid optimization. These include the lack of standardized datasets and data quality issues, interpretability and explain-ability of machine learning models, ethical and social implications of using machine learning, and integration with existing energy infrastructure and regulatory frameworks. Having a clear understanding that continued research and developments in deep learning applications to energy field are crucial for achieving a sustainable and efficient energy future. This paper therefore reviewed existing literature for challenges and opportunities associated with deep machine learning in energy grid optimization; and highlights the importance of continued research and development in the field. The paper found out that opportunities for future research in deep machine learning for energy grid optimization include advancements in machine learning algorithms and techniques, development of new datasets and data collection methods, integration of machine learning with other emerging technologies. It also established needs for collaborative research and public-private partnerships.

Wireless sensor networks are attractive largely because they need no wired infrastructure. But precisely this feature makes them energy constrained. Recent studies find that sensing behaviors that are otherwise deemed efficient consume comparable energy with communication. The duty cycle scheduling is perceived as contributing to achieving energy efficiency of sensing. Because of different research assumptions and objectives, various scheduling schemes have various emphases. This paper designed an adaptive sensing scheduling strategy. The objective function of the scheduling strategy includes minimizing average energy expenditure and maximizing sensing coverage (reducing event miss-rate), and it requires relatively loose assumptions. We determine the functional relationship between the variables of the objective function and the step-size parameters of the proposed strategy through the numerical fitting. We found that the objective function aggregated by the fitting functions is a bivariate multi-peak function that favors the Fibonacci tree optimization algorithm. Once the optimization of parameters is done, the strategy can be easily deployed and behaves consistently in the coming hours. We name the proposed strategy as “FTOS”. The experimental results show that the Fibonacci tree optimization algorithm gets a better optimistic effect than the comprehensive learning particle swarm optimization (CLPSO) algorithm and differential evolution (DE) algorithm. The FTOS strategy is superior to the fixed time scheduling strategy in achieving the scheduling objectives. It also outperforms other strategies with the same scheduling objectives such as LDAS, BS, DSS and PECAS.

The building and construction sector has a significant impact on CO2 emissions and pollutants released into the atmosphere, which contribute to climate change. The EPDB Directive mandates the achievement of a minimum energy class E for all residential buildings by 2030 and an energy class D by 2033. Particularly, in Italy, about 86% of the existing building stock predates the enactment of any energy laws and regulations, making it imperative to apply the energy efficiency interventions. This paper provides a support decision tool for the identification of standardized interventions on the envelope, air conditioning system and domestic hot water production. The study is focused on a specific construction period class (1976 - 1990) in six different climatic zones. The methodological approach is based on a cataloguing phase and definition of Ante Operam energy classes, on the case study identification, the energy requalification interventions identification, solutions simulations, cost estimation. By simulating standardized interventions for each climatic zone, a range of possible combinations will be identified. The most advantageous ones will be determined based on a cost-benefit analysis, considering the potential class jump achieved. The research result is a matrix of energy efficiency interventions that is applicable to each climatic zone and can be extended to the existing housing stock.

Reducing office buildings’ energy consumption can contribute significantly towards carbon reduction commitments since it represents 10% of total energy consumption. Major components are lighting (40% of consumption), electrical equipment (35%), and heating and central cooling systems (25\%). Occupants’ behaviours impact these energy consumption components, with solid evidence on the role of individual behaviours. In this work, we propose a methodology that uses virtual choreographies to identify and prioritize behaviour-change interventions towards office users based on the potential impact on energy consumption. The data shows that some behaviours with significant consumption have little potential for behavioural change impact, while other behaviours hold substantial potential for lowering energy consumption via behavioural change.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. This study reviews the state-of-the-art ML applications in the biofuels’ life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx, CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. The purpose of the present study is to review the state-of-the-art ML applications in the biofuels' life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

Energy efficiency considerations in terms of reduced power dissipation is a significant issue in the design of digital circuits for very large-scale integration (VLSI) systems. Quantum-dot cellular automata (QCA) is an emerging ultra-low power dissipation approach, distinct from the traditional complementary metal-oxide semiconductor (CMOS) technology, for building digital computing circuits. Developing fully reversible QCA circuits has the potential to significantly reduce energy dissipation. The multiplexer is a fundamental element in the construction of useful digital circuits. In this paper, a novel, multilayer, fully reversible QCA 8:1 multiplexer circuit, with ultralow energy dissipation, is introduced. The proposed multiplexer power dissipation is simulated using the QCADesigner-E version 2.2 tool, describing the microscopic physical mechanisms underlying the QCA operation. The results showed that the proposed reversible QCA 8:1 multiplexer consumes 89% less energy than the most energy-efficient 8:1 multiplexer circuit presented previously in the scientific literature.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Energy demand forecasting is a fundamental aspect of modern energy management. It impacts resource planning, economic stability, environmental sustainability, and energy security. This importance is making it critical for countries worldwide, particularly in cases like Türkiye, where the energy dependency ratio is notably high. The goal of this study is to propose ensemble machine learning methods such as boosting, bagging, blending, and stacking with hyperparameter tuning and k-fold cross-validation, and investigate the application of these methods for predicting Türkiye's energy demand. This study utilizes population, GDP per capita, imports and exports as input parameters based on historical data from 1979 to 2021 in Türkiye. Eleven combinations of all predictor variables were analyzed, and the best one was selected. It was observed that a very high correlation exists among population, GDP, imports, exports, and energy demand. In the first phase, the preliminary performance was investigated of 19 different machine learning algorithms using 5-fold cross-validation and measured their performance using five different metrics: MSE, RMSE, MAE, R-squared, and MAPE. Secondly, ensemble models were constructed by utilizing individual machine learning algorithms, and the performance of these ensemble models was compared with both each other and the best-performing individual machine learning algorithm. The analysis of the results revealed that placing Ridge as the meta-learner and using ET, RF and Ridge as the base learners in the stacking ensemble model produced superior results compared to the other models across performance metrics. It is anticipated that the findings of this research can be applied globally and prove valuable for energy policy planning in any country. The results obtained not only highlight the accuracy and effectiveness of our predictive model but also underscore the broader implications of this study within the framework of the United Nations' Sustainable Development Goals (SDGs).

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

To compare the quality of low-energy VMIs obtained with three DECT platforms according to phantom diameter. Three sections of the Mercury Phantom 4.0 were scanned on two generations of split-filter CTs (SFCT-1st and SFCT-2nd) and on one Dual-source CT (DSCT). Noise power spectrum (NPS), task-based transfer function (TTF) and detectability index (d’) were assessed on VMIs from 40 to 70keV. Highest noise magnitude values were found with SFCT-1st and noise magnitude was higher with DSCT than with SFCT-2nd for 26-cm (10.2±1.3%) and 31-cm (7.0±2.5%), and the opposite for 36-cm (-4.2±2.5%). The highest average NPS spatial frequencies and TTF values at 50% (f50) values were found with DSCT. For all energy levels, f50 values were higher with SFCT-2nd than SFCT-1st for 26-cm (3.2±0.4%) and the opposite for 31-cm (-6.9±0.5%) and 36-cm (-5.6±0.7%). The lowest d’ values were found with SFCT-1st. For all energy levels, d’ values were lower with SFCT-2nd than with DSCT for 26-cm (-6.2±0.7%), similar for 31-cm (-0.3±1.9%) and higher for 36-cm (5.4±2.7%). In conclusion, compared to SFCT-1st, SFCT-2nd exhibited lower noise magnitude and higher detectability values. Compared with DSCT, SFCT-2nd had lower noise magnitude and higher detectability for the 26-cm but the opposite was true for the 36-cm.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable frequency drives (VFDs) makes the motor efficiency data published by manufacturers inapplicable, the fan efficiency and drive (belt-motor-VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD-motor-fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency and drive efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then the energy model is identified for an existing VFD-motor-fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD-motor-fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

Transportation, environmental conditions, quality of human life within smart cities, and system infrastructure have all needed practical and dependable smart solutions as urbanization has accelerated in recent years. In addition, the emerging Internet of Things (IoT) provides access to a plethora of cutting-edge, all-encompassing apps for smart cities, all of which contribute significantly to lowering energy consumption and other negative environmental impacts. For smart cities to meet the challenge of using less energy, the authors of this research article suggest planning and implementing an integrated power and heat architecture that puts renewable energy infrastructure and energy-storage infrastructure at the top of the list. To address these issues, we describe a smart proposed NEOSRD architecture that uses a distributed smart area domain to optimize renewable demand energy in a smart city across a wide area network. The energy requirements of desalination procedures are negligible when compared to the total local energy consumption and transportation, a feat accomplished by the proposed NEOSRD system. Here, the computational model shows how the established system is a valuable response to our problems and a cost-effective strategy for creating smarter structural elements that cut down on overall smart cities' energy costs.

Abstract: Wireless body area networks (WBANs) have strong potential in the field of health monitoring. However, the energy consumption required for accurate monitoring limits the time between battery charges of the wearable sensors, which is a key performance factor (and can be critical in the case of implantable devices). In this paper, we study the inherent trade-off between the power consumption of the sensors and the probability of misclassifying a patient’s health state. We formulate this trade-off as a dynamic problem, in which at each step we can choose to activate a subset of sensors that provide noisy measurements of the patient’s health state. We assume that the (unknown) health state follows a Markov chain, so our problem is formulated as a partially observable Markov decision problem (POMDP). We show that all the past measurements can be summarized as a belief state on the true health state of the patient, which allows tackling the POMDP problem as an MDP on the belief state. We then empirically study the performance of a greedy one-step look-ahead policy compared to the optimal policy obtained by solving the dynamic program. For that purpose, we use an open-source Continuous Glucose Monitoring (CGM) data set of 232 patients over six months and extract the transition matrix and sensor accuracies from the data. We find that the greedy policy saves ~50% of the energy costs while reducing the misclassification costs by less than 2% compared to the most accurate policy possible that always activates all sensors. Our sensitivity analysis reveals that the greedy policy remains nearly optimal across different cost parameters and a varying number of sensors. The results also have practical importance, because while the optimal policy is too complicated, a greedy one-step look-ahead policy can be easily implemented in WBAN systems.

This paper attempts to alter a prevailing assumption that buildings use energy to an understanding that in fact, people use energy. Therefore, to successfully accelerate the transition to a low-carbon society and economy more emphasis should be on motivating people and increasing their awareness by making them energy conscious building users and therefore active players in the energy transition process. In this context, this paper provides insights from the Horizon 2020 MOBISTYLE project. It demonstrates research and development approaches, highlights the main project objectives, and presents findings of an ethnographic (qualitative) study of users’ habits, practices, and needs. The aim of the project is to motivate behavioural change by raising consumer awareness through the provision of attractive personalized information on user’s energy use, indoor environment and health, all enabled by an integrated information and communication technology (ICT) service. In this context, the anthropological people-centred approach is integrated into the MOBISTYLE approach putting users at the centre of the ICT tools development process. The main quantitative objective of the project is a reduction of energy use for at least 16 % prompted by the provision of combined information and feedback systems on energy, indoor environmental quality (IEQ) and health. The most relevant motivational factors and key performance indicators (KPIs) for encouraging a more energy conscious and healthy lifestyle were defined by means of a people-centred approach, adopting anthropological inquiries in different settings. Information about users’ lifestyles and their needs was collected in focus groups with potential users in five case studies, located in different European Union (EU) countries. Behaviour change is achieved through awareness campaigns, which encourage users to be pro-active about their energy consumption and to simultaneously improve health and well-being.

This work explores state-of-the-art approaches for stabilizing an inverted pendulum on a cart system, which has been used for over a century to demonstrate ideas in nonlinear and linear control theory, owing to its simple practical implementation yet complex system dynamics. We introduce energy-based control methods and propose a simple linear controller to quickly force the system to the downward equilibrium before swing-up. By constraining the system to start from a stable equilibrium configuration, the problem of global stability is reduced to ensuring that the system can follow all heteroclinic orbits that start very close to the downward equilibrium. Multiple Lyapunov functions are employed to ensure non-zero tracking, increasing the system's domain of attraction than is achieved by traditional controllers based on a single Lyapunov function. We stabilize our inverted pendulum system in the upright configuration through pole placement using a linear quadratic regulator known for fast settling times and smooth system response and through sliding mode controllers known for their robustness to disturbances and model uncertainties. While sliding mode controllers exhibit faster stabilization of the pendulum angle, they fail to stabilize the cart position in a reasonable amount of time. The paper concludes by suggesting various controller techniques that can enhance the swing-up and stabilization controller architectures, leaving room for future exploration. To facilitate further research and education, an open-source MATLAB simulation code is provided, encapsulating the system dynamics and controller designs. This resource offers flexibility for customization, making it a valuable tool for both researchers and educators working with inverted pendulum systems.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Sensor networks, as a special subtype of wireless networks, consist of sets of wirelessly connected sensor nodes often placed in hard-to-reach environments. Therefore, it is expected that sensor nodes will not be powered from the power grid. Instead, sensor nodes have their own power sources, the replacement of which is often impractical and requires additional costs, so it is necessary to ensure minimum energy consumption. For that reason, the energy efficiency of wireless sensor networks used for monitoring environmental parameters is essential, especially in remote networking scenarios. In this paper, an overview of the latest research progress on wireless sensor networks based on LoRa was provided. Furthermore, the analyses of the energy consumption of sensor nodes used in agriculture to observe environmental parameters were carried out. Optimization methods of energy consumption, in terms of choosing the appropriate data collection processes, as well as the settings of wireless network radio parameters were suggested. In the conducted analyses, special emphasis was placed on choosing the optimal package size. In this paper, it was proven that the adjustment of the transmission speed to the actual size of the packet is important for better energy efficiency of communication.

With the widespread use of electric machines there is a growing need to extract information from the machines to optimize their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of an squirrel cage induction motor rotor physical variables. The system comprises: circuit to acquire desirable rotor variable(s) value(s) and send it to the computer; a rectifier and power storage circuit that besides converting an alternating current in continuous also store energy for a certain amount of time to wait the motor engine shutdown; and magnetic generator that harvest energy from rotating field to power the circuits mentioned above. The embedded system is set on the rotor, making it difficult to power the system because it is rotating, problem solved with the construction of the magnetic generator eliminating the need of using batteries or collector rings and send data to the computer using a wireless NRF24L01 module. For the proposed system validation a temperature sensor (DS18b20) was used, variable known as the most important when identifying the need for maintenance and control systems. Tests were made getting satisfactory results proving the viability of using sensors on the rotor.

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

In this paper, modification of dual-Halbach permanent magnet (PM) array is investigated to improve performance of tubular linear machine, in terms of flux density and output power. Instead of a classical Halbach array with only radial and axial PMs, proposed model involves insertion of mig-magnets, which have magnetized angle shifted from the reference magnetized angles of axial and radial PMs. This structure leads to elimination of flux leakage and concentration of flux linkage in middle of the coil; therefore, the performance of machine is increased.

Live attenuated vaccines have through history proved themselves as safe and efficient. Pasteur has developed a vaccine against rabies, through a long process of passage of the virus wild type through rabbits. The result was one of the most efficient attenuated live-virus vaccines. This paper suggests a method based on calculations of biothermodynamic properties of potential tissues for vaccine application, predilected host tissue and virus wild type. Gibbs energy of biosynthesis represents the thermodynamic driving force for virus multiplication. The attenuated strain of the virus should possess Gibbs energy of biosynthesis, which is less negative than the predilected target tissue, but more negative than the vaccine portal tissue. In that way, the attenuated virus strain should be able to multiply in the vaccine portal of entry tissue and cause an immune response, making it efficient. On the other hand, the attenuated strain cannot multiply in the predilected host tissue, making it safe. The attenuation is achieved by adding a gene to the virus, which encodes a ballast protein. Production of the ballast protein would make virus multiplication less favorable, since it would require energy, but be useless to the virus.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

Heat emitters constitute the primary devices used in space heating and cover a fundamental role in the energy efficient use of buildings. In the search for an optimized design, heating devices should be compared with a benchmark emitter with maximum heat emission efficiency. However, such an ideal heater still needs to be defined. In this paper we perform an analysis of heat transfer in a European reference room, considering room side effects of thermal radiation and computing the induced operative temperature both analytically and numerically. By means of functional optimization, we analyse trends such as the variation of operative temperature with radiator panel dimensions, finding optimal configurations. In order to make our definitions as general as possible, we address panel radiators, convectors, underfloor (UFH) and ceiling heater. We obtain analytical formulas for the operative temperature induced by panel radiators and identify the 10-type as our ideal radiator, while the UFH provides the best performance overall. Regarding specifically UFH and ceiling heaters, we find optimal sizes that identify the according ideal emitters. The analytical method and quantitative results reported in this paper can be generalized and adopted in most studies concerning the efficiency of different heat emitter types in building enclosures.

The Mine Internet of Things (MIoT), as a key technology for reconstructing post-disaster communication networks, enables to realize the safety monitoring and controlling of the affected roadway. However, due to the challenging underground mine environment, the MIoT suffers from severe signal attenuation, vulnerable nodes, and limited energy, which result in low network reliability of the post-disaster MIoT. To improve the transmission reliability as well as to reduce energy consumption, a directional-area-forwarding-based energy-efficient opportunistic routing (DEOR) for the post-disaster MIoT is proposed. DEOR defines a forwarding zone (FZ) for each node to route packets toward the sink. The candidate forwarding set (CFS) is constructed by the nodes within the FZ that satisfy the energy constraint and the neighboring node degree constraint. The nodes in CFS are prioritized based on the routing quality evaluation by taking the local attributes of nodes into consideration, such as the directional angle, transmission distance, and residual energy. DEOR adopts a recovery mechanism to address the issue of void nodes. The simulation results validate that the proposed DEOR outperforms ORR, OBRN and ECSOR in terms of energy consumption, average hop count, packet delivery rate, and network lifetime.

Industry 4.0 brings advanced technologies and automation, enabling greater productivity and efficiency. However, it also increases energy consumption and carbon emissions. Sustainable manufacturing in the era of Industry 4.0 is vital for addressing the environmental impact by minimizing resource consumption, optimizing energy efficiency, and adopting eco-friendly practices. CNC (Computer Numeric Control) 5-axis milling plays a significant role in the machining of precision molds and dies, aerospace, consumer electronics, etc. This research aims to explore the potential of the artificial intelligence (AI) technique in improving energy efficiency on CNC 5-axis milling process for sustainable manufacturing. The experiments were carried out using a CNC 5-axis milling machine with various machining parameters, toolpath planning, and dry cutting condition. Data on energy consumption of CNC 5-axis milling machine were collected, then the relationship between the machining parameters, toolpath planning, and energy consumption was analyzed and built. Furthermore, an AI-based optimization algorithm was developed that uses machine learning and optimization techniques to identify energy-efficient machining strategies. The developed algorithm was implemented within a simulation framework, the algorithm was rigorously assessed using machine learning analysis to effectively reduce energy consumption, all while ensuring the accuracy of machining result. Finally, verification experiments were carried out to evaluate the applicability and performance of the AI-based energy optimization approach on a CNC 5-axis milling machine. By integrating AI into the CNC machining process, manufacturers can achieve significant energy savings, leading to reduced carbon emissions and improved sustainability.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

This paper provides a review of an emerging field in the food processing sector, referring to efficient and safe food supply chains, ’from farm to fork’, as enabled by Artificial Intelligence (AI). Recent advances in machine and deep learning are used for effective food production, energy management and food labeling. Appropriate deep neural architectures are adopted and used for this purpose, including Fully Convolutional Networks, Long Short-Term Memories and Recurrent Neural Networks, Auto-Encoders and Attention mechanisms, Latent Variable extraction and clustering, as well as Domain Adaptation. Three experimental studies are presented, illustrating the ability of these AI methodologies to produce state-of-the-art performance in the whole food supply chain. In particular, these concern: (i) predicting plant growth and tomato yield in greenhouses, thus matching food production to market needs and reducing food waste or food unavailability; (ii) optimizing energy consumption across large networks of food retail refrigeration systems, through optimal selection of systems that can get shut-down and through prediction of the respective food de-freezing times, during peaks of power demand load; (iii) optical recognition and verification of food consumption expiry date in automatic inspection of retail packaged food, thus ensuring safety of food and people’s health.

We review our theory of interdependence applied to autonomous human-machine teams, with which we have made several generalizations based on theory that have led to new discoveries, compared to social science which is struggling to break free of its validation crisis, but also has no generalizations to new discoveries with human teams, let alone to human-machine teams. In this invited article, based around the stability of a team, of our discoveries, we review the uncertainty between a team's structure and its performance, our first finding. We generalize that finding to deception, vulnerability, innovation and fittedness. From there, our next generalization is to the quantum likeness of interdependence and quantum mechanics; we move on to Shannon holes, knowledge, and conclude with the value of debate and the need for boundaries to contain debate, to reduce interference, and to protect states of interdependence. After the introduction, we extend our model in Section 2 to energy and time, and we close with a brief review of innovation and future plans.

Energy efficiency of Data Center (DC) operations heavily relies on IT and cooling systems performance. A reliable and efficient cooling system is necessary to produce a persistent flow of cold air to cool servers that are subjected to constantly increasing computational load due to the advent of IoT- enabled smart systems. Consequently, increased demand for computing power will bring about increased waste heat dissipation in data centers. In order to bring about a DC energy efficiency, it is imperative to explore the thermal characteristics analysis of an IT room (due to waste heat). This work encompasses the employment of an unsupervised machine learning modelling technique for uncovering weaknesses of the DC cooling system based on real DC monitoring thermal data. The findings of the analysis result in the identification of areas for energy efficiency improvement that will feed into DC recommendations. The methodology employed for this research includes statistical analysis of IT room thermal characteristics, and the identification of individual servers that frequently occur in the hotspot zones. A critical analysis has been conducted on available big dataset of ambient air temperature in the hot aisle of ENEA Portici CRESCO6 computing cluster. Clustering techniques have been used for hotspots localization as well as categorization of nodes based on surrounding air temperature ranges. The principles and approaches covered in this work are replicable for energy efficiency evaluation of any DC and thus, foster transferability. This work showcases applicability of best practices and guidelines in the context of a real commercial DC that transcends the set of existing metrics for DC energy efficiency assessment.

1960s Europe saw a large number of residential neighborhoods built to house those migrating from the countryside. Today, more than 50 years later, these neighborhoods suffer high levels of functional, social, and technical obsolescence. In response to this, University of Seville developed the Aura Strategy as an intervention methodology to find global solutions to issues in outdated neighborhoods. To provide visibility to this aspect of the Aura strategy, the retrofit proposal presented in this article provides a solution to improve the roofing of buildings in a case study neighborhood (Polígono de San Pablo, Seville) and an analysis of the results in terms of energy and financial savings for local residents. The results show that for a population of roughly 18,000 (in 2018), net savings, including energy and retrofitting costs, ranging from nearly 6.5 to over 8.6 million can be made over the 20-year life cycle span. Likewise, the results obtained on the reduction of thermal loads indicate a 72% decrease in energy consumption, equivalent to a saving of close to 4,500 tons of greenhouse gas emissions for the district and the entire life cycle time period, with the consequent benefits on the impact on air quality and and the fight against climate change. climate change.

Atrial Fibrillation (AF) is known as one of the dominant cardiac disease that is associated with severe consequences such as risk of strokes. This cardiac arrhythmia can be efficiently diagnosed using EEG signals. However, AF episodes in EEG records are not always permanent for all subjects. In addition, lengthy subject preparation and ECG recording sessions makes this practice time consuming and not attractive for efficient diagnosis. One attractive solution for this problem will be the use of wearable Internet of Medical Things IoMT devices for EEG recording and AF detection. From another side the use machine learning for efficient diagnosis could provide high accurate diagnosis. However, the deployment of these wireless wearable devices faces the problems of limited processing capabilities and of energy scarcity. In this context, the design of energy efficient accurate on-sensor AF detection scheme using machine learning algorithms still requires a focused research effort. This paper proposes a wearable solution for ECG-based processing scheme for embedded AF detection. The proposed method achieved 100% sensitivity and 94.5% of specificity and accuracy of around 97.4 % for wide range of subjects while showing low energy-consumption. The obtained results show the efficiency of using Logistic Regression algorithm for accurate AF detection and attest about practical feasibility of the proposed approach in wearable IoMT devices.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

Machine learning (ML) methods has recently contributed very well in the advancement of the prediction models used for energy consumption. Such models highly improve the accuracy, robustness, and precision and the generalization ability of the conventional time series forecasting tools. This article reviews the state of the art of machine learning models used in the general application of energy consumption. Through a novel search and taxonomy the most relevant literature in the field are classified according to the ML modeling technique, energy type, perdition type, and the application area. A comprehensive review of the literature identifies the major ML methods, their application and a discussion on the evaluation of their effectiveness in energy consumption prediction. This paper further makes a conclusion on the trend and the effectiveness of the ML models. As the result, this research reports an outstanding rise in the accuracy and an ever increasing performance of the prediction technologies using the novel hybrid and ensemble prediction models.

In this paper, we propose an adaptive duty-cycled hybrid X-MAC (ADX-MAC) protocol for energy-efficient forest fire prediction. The X-MAC protocol acquires the additional environmental status collected by each forest fire monitoring sensor for a certain period. And, based on these values, the length of sleep interval of duty-cycle is changed to efficiently calculate the risk of occurrence of forest fire according to the mountain environment. The performance of the proposed ADX-MAC protocol was verified through experiments the proposed ADX-MAC protocol improves throughput by 19% and was more energy-efficient by 24% compared to X-MAC protocol. As the probability of forest fires increases, the length of the duty cycle is shortened, confirming that the forest fires are detected at a faster cycle.

Building energy consumption plays an essential role in urban sustainability. The prediction of the energy demand is also of particular importance for developing smart cities and urban planning. Machine learning has recently contributed to the advancement of methods and technologies to predict demand and consumption for building energy systems. This paper presents a state of the art of machine learning models and evaluates the performance of these models. Through a systematic review and a comprehensive taxonomy, the advances of machine learning are carefully investigated and promising models are introduced.

This study focused on the predictive models incorporating machine learning techniques that induce new dynamics for forecasting energy generation, enabling effective planning, financing, and system monitoring. The research developed a machine learning-based power generation prediction model tailored explicitly for Kenya's Garissa solar power plant. The selected model demonstrated a root mean squared error of 5.23 during evaluation, resulting in a prediction accuracy of 90.42%. This high accuracy indicates that the model can be relied upon for precise generation prediction, facilitating effective planning, and system performance monitoring

Underwater wireless sensor networks (UWSNs) represent a specialized category of WSNs with versatile applications including acoustic monitoring, oil and gas exploration, and military surveillance. UWSNs face formidable challenges such as limited energy resources, extended propagation delays, and harsh conditions. Existing clustering and multi-hop routing protocols often unevenly distribute nodes geographically, causing network fragmentation and disproportionately draining the battery life of nodes near the sink due to higher data transmission demands. In this paper, we introduce an Energy-efficient Artificial Fish Swarm-based Clustering Protocol (EAFSCP), inspired by the collective behavior of fish swarms. EAFSCP is a decentralized clustering algorithm designed for acoustic monitoring in UWSNs. Its decentralized nature makes it particularly well-suited for large-scale UWSNs, where centralized algorithms may not be feasible. Through comprehensive comparisons with existing cluster-based routing protocols, our findings indicate that EAFSCP consistently outperforms them across multiple key performance metrics, including network lifetime, energy consumption, packet delivery ratio, packet loss rate, and throughput. According to the results, EAFSCP represents an effective clustering algorithm that enhances network performance, prolongs network lifespan by reducing energy consumption, promotes scalability, and provides valuable guidance for emergency response efforts.

The radio operation in wireless sensor networks (WSN) in the Internet of Things (IoT) applications are the most common source for power consumption. However, recognizing and controlling the factors affecting radio operation can be valuable for managing the node power consumption. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS used in WakeUp mode, which is a clear channel assessment (CCA) to check radio status periodically. The time spent to check the radio is of utmost importance for monitoring power consumption. It can lead to false WakeUp or idle listening in Radio Duty-Cycles and ContikiMAC. This paper presents a detailed analysis of radio WakeUp time factors of ContikiMAC. Then, we propose lightweight CCA (LW-CCA) as an extension to ContikiMAC to reduce the percentage of Radio Duty-Cycles in false WakeUps and idle listenings by using dynamic received signal strength indicators (RSSI) status check time. The simulation results in the Cooja simulator show that LW-CCA reduces about 8% energy consumption in nodes while maintaining up to 99% of the packet delivery rate (PDR).

The aims of this paper can be traced back to goals number seven, twelve and thirteen introduced by Agenda 2030, namely "affordable and clean energy", “responsible consumption and production” and "climate action”, respectively. This is due to the fact that the present work supports decarbonization processes acting in a direct way on the electricity consumption achieved by plants pertaining to the waste industry; in fact, this study aims at the realization of a machine learning model for predicting the energy consumption achieved by a mechanical biological treatment (MBT) waste plant located in central Italy, given the distribution of the entering waste. This model is implemented in MATLAB. The model can be used to tune the distribution of the entering waste in order to adapt the plant energy consumption to the capability of the energy sources and can serve as a play-ground model for other energy transformation plants. The results of the study, which feed the literature on the application of artificial intelligence to real industrial plants, could be used to determine energy efficiency actions that could be incorporated into Property’s strategic planning.

Estimating evapotranspiration at field scale is a major component of sustainable water management. Due to the difficulty to assess some major unknowns of the water cycle at that scale, including irrigation amounts, evapotranspiration is often computed as the residual of the instantaneous surface energy budget. One of the Surface Energy Bal-ance components with the largest uncertainties in their quantification over bare soils and sparse vegetation areas is the ground heat flux (G). Over the last decades, the es-timation of G with RS data has been mainly achieved with empirical equations, on the basis of the G and net radiation (Rn) ratio, G/Rn. G/Rn empirical equations generally require vegetation data (Type I empirical equations), in combination with surface tem-perature (Ts) and albedo (Type II empirical equations). In this article we aim to evalu-ate the estimation of G with RS. For the first time, we compare eight G/Rn empirical equations against two types of machine learning (ML) methods: an ensemble ML type, the Random Forest (RF), and the Neural Networks (NN). The comparison of each method is evaluated over dense dataset, including a wide range of climate and land covers, with data of Eddy-Covariance towers extended along the mid-latitude area that encompass the European and African continent. Our results have shown evidence that the driver of G in bare soils and sparse vegetation areas (Fraction of Vegetation, Fv <= 0.25) is Ts, instead of vegetation greenness indexes. On the other hand, the estimation of G with Rn, Ts or Fv decreases at dense vegetation areas (Fv >= 0.50). There are not significant differences between the most accurate type I and II empirical equations. For bare soils and sparse vegetation areas the empirical equation that better estimates G is E8, which combines the Leaf Area Index (LAI) and Ts. In dense vegetation areas (Fv >= 0.25), an exponential empirical equation based on Fv (E4), shows the best performance. However, ML better estimates G than the empirical equations, independently of the Fv ranges. A RF model with Rn, LAI and Ts as predictor variables shows the best accuracy and performance metrics, outperforming the NN model.

Hydrogen powered vehicles use high-pressure reservoirs from which the gas is transferred to the low-pressure fuel-cell via a classical pressure reduction valve. In these systems no expansion work is recovered and the question is addressed of the potential to increase the global efficiency by using an expansion machine between the reservoir and the electrochemical reactor. This paper investigates the feasibility of such an expansion machine, evaluates the mechanical constraints in terms of forces, torques and produced power by numeric simulation. It further evaluates the energetic contribution to the whole conversion chain from the hydrogen reservoir to the common electrical network on board. A low energy contribution of the expansion system addresses the question of the real benefit of such an investment.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

This article presents a review of current advances and future prospects in the field of forecasting renewable energy generation using machine learning (ML) and deep learning (DL) techniques. With the increasing penetration of renewable energy sources (RES) into the electricity grid, accurate forecasting of their generation becomes crucial for efficient grid operation and energy management. Traditional forecasting methods have limitations, and thus ML and DL algorithms have gained popularity due to their ability to learn complex relationships from data and provide accurate predictions. This paper reviews the different approaches and models that have been used for renewable energy forecasting and discusses their strengths and limitations. It also highlights the challenges and future research directions in the field, such as dealing with uncertainty and variability in renewable energy generation, data availability, and model interpretability. Finally, this paper emphasizes the importance of developing robust and accurate renewable energy forecasting models to enable the integration of RES into the electricity grid and facilitate the transition towards a sustainable energy future.

Electricity demand prediction is vital for energy production management and proper exploitation of the present resources. Recently, several novel machine learning (ML) models have been employed for electricity demand prediction to estimate the future prospects of the energy requirements. The main objective of this study is to review the various ML models applied for electricity demand prediction. Through a novel search and taxonomy, the most relevant original research articles in the field are identified and further classified according to the ML modeling technique, perdition type, and the application area. A comprehensive review of the literature identifies the major ML models, their applications and a discussion on the evaluation of their performance. This paper further makes a discussion on the trend and the performance of the ML models. As the result, this research reports an outstanding rise in the accuracy, robustness, precision and the generalization ability of the prediction models using the hybrid and ensemble ML algorithms.

Researchers are always looking to find ways to use energy more efficiently while keeping people comfortable at home. They've tried different methods like fuzzy logic and genetic algorithms to do this. In this paper, we introduce a novel model that combines different techniques like data smoothing, optimization, machine learning, and control algorithms to reach this goal in smart homes. The proposed model is made up of three main parts: smoothing, optimization, and control. The smoothing part uses the Kalman filter to get rid of any unnecessary noise and make sure the data used to predict energy use is clean and smooth. The optimization part uses both genetic with firefly algorithms and artificial neural networks to minimize the gap between the actual environmental conditions and the conditions users find comfortable. It adjusts the comfort settings in real-time using machine learning. The control part uses Mamdani fuzzy logic to make sure energy is delivered in the best way possible to the systems that control temperature, lighting, etc., making the home comfortable and saving energy at the same time. Comparative analyses demonstrate the superiority of the proposed model over existing algorithms, including the Particle Swarm Optimization (PSO) algorithm. Additionally, the paper discusses the importance of adaptive controllers in addressing issues associated with incorrect PID controller selection and highlights the benefits of using the FA-GA in energy optimization and comfort improvement. Overall, the proposed model offers an effective solution for efficient energy consumption optimization and enhanced user comfort in diverse settings through the integration of advanced algorithms and optimization modules.

Wrist-worn fitness trackers and smartwatches are proliferating with an incessant attention towards health tracking. Given the growing popularity of wrist-worn devices across all age groups, a rigorous evaluation for recognizing hallmark measures of physical activities and estimating energy expenditure is needed to compare their accuracy across the lifespan. The goal of the study was to build machine learning models to recognize physical activity type (sedentary, locomotion, and lifestyle) and intensity (low, light, and moderate), identify individual physical activities, and estimate energy expenditure. The primary aim of this study was to build and compare models for different age groups: young [20-50 years], middle (50-70 years], and old (70-89 years]. Participants (n = 253, 62% women, aged 20-89 years old) performed a battery of 33 daily activities in a standardized laboratory setting while wearing a portable metabolic unit to measure energy expenditure that was used to gauge metabolic intensity. Tri-axial accelerometer collected data at 80-100 Hz from the right wrist that was processed for 49 features. Results from random forests algorithm were quite accurate in recognizing physical activity type, the F1-Score range across age groups was: sedentary [0.955 – 0.973], locomotion [0.942 – 0.964], and lifestyle [0.913 – 0.949]. Recognizing physical activity intensity resulted in lower performance, the F1-Score range across age groups was: sedentary [0.919 – 0.947], light [0.813 – 0.828], and moderate [0.846 – 0.875]. The root mean square error range was [0.835 – 1.009] for the estimation of energy expenditure. The F1-Score range for recognizing individual physical activities was [0.263 – 0.784]. Performances were relatively similar and the accelerometer data features were ranked similarly between age groups. In conclusion, data features derived from wrist worn accelerometers lead to high-moderate accuracy estimating physical activity type, intensity and energy expenditure and are robust to potential age-differences.

Solar radiation prediction is an important process in ensuring optimal exploitation of solar energy power. Numerous models have been applied to this problem, such as numerical weather prediction models and artificial intelligence models. However, well-designed hybridization approaches that combine numerical models with artificial intelligence models to yield a more powerful model can provide a significant improvement in prediction accuracy. In this paper, we propose novel hybrid machine learning approaches that exploit auxiliary numerical data. The proposed hybrid methods invoke different machine learning paradigms, including feature selection, classification, and regression. Additionally, numerical weather prediction (NWP) models are used in the proposed hybrid models. Feature selection is used for feature space dimension reduction to reduce the large number of recorded parameters that affect estimation and prediction processes. The rough set theory is applied for attribute reduction and the dependency degree is used as a fitness function. We investigate the effect of the attribute reduction process with thirty different classification and prediction models in addition to the proposed hybrid model. Then, different machine learning models are constructed based on classification and regression techniques to predict solar radiation. Moreover, other hybrid prediction models are formulated to use the output of the numerical model of Weather Research and Forecasting (WRF) as learning elements in order to improve the prediction accuracy. The proposed methodologies are evaluated using a data set that is collected from different regions in Saudi Arabia.

Responsible, efficient, and environmentally conscious energy consumption practices are increasingly essential for ensuring the reliability of the modern electricity grid. This study focuses on leveraging time series analysis to improve forecasting accuracy, crucial for various application domains where real-world time series data often exhibit complex, non-linear patterns. Our approach advocates for utilizing Long Short Term Memory (LSTM) and Bidirectional LSTM (BiLSTM) models for precise time series forecasting. To ensure a fair evaluation, we compare the performance of our proposed approach with traditional neural networks, time-series forecasting methods, and conventional decline curves. Additionally, individual models based on LSTM, Bi-LSTM, and other machine learning methods are implemented for a comprehensive assessment. Experimental results consistently demonstrate that our proposed model outperforms all benchmarking methods in terms of mean absolute error (MAE) across most datasets. Addressing the imbalance between activations by consumer and prosumer groups, our predictions show superior performance compared to several traditional forecasting methods, such as the Autoregressive Integrated Moving Average model (ARIMA) and Seasonal Autoregressive Integrated Moving Average model (SARIMA). Specifically, the root mean square error (RMSE) of Bi-LSTM is 5.35%, 46.08%, and 50.6% lower than LSTM, ARIMA, and SARIMA, respectively, on the May test data.

The product is a centrifugal air extractor, whose objective is to extract the stale air of SARS-CoV-2 or Covid-19 (Coronavirus); designed for civil and commercial use, it works with a single-phase alternating current (AC) motor of 220 (V) and 50 (Hz), with high energy efficiency (EE). Developed under the Design Thinking methodology, by electromechanical simulation using NI Multisim 14.0 software, case design using Cfturbo 2020 R2.0 CAD software, and rapid 3D prototyping with the OverLord Pro printer; with a prototype of the conventional stator winding of a synchronous motor with a two-pole PMSM/IPM single-phase alternating current (AC) field winding and a 4000 (Gauss) ferromagnetic ceramic magnet rotor. Innovating online nº 15 of invention patent nº 381968 by Nikola Tesla, 5/1/1888.One of the objectives is to link the middle level or Technical Schools with the University system (and careers with a Technological profile) through Project B374 located in the Secretariat of Science and Technology (SCyT) of the National University of La Plata ( UNLP), whose title is: “Integrated Management of Design and Innovation. Contributions for a theoretical-conceptual and methodological review” by the Director: Mg. Federico del Giorgio Solfa. Just as links were sought with the Research and Development Laboratory of the Department of Industrial Design (LIDDI-FBA-UNLP) through its Director D.I. Pablo Ungaro and D.I. Ana Bocos. In 2021, the project participated in the INNOVAR National Contest of the Ministry of Science, Technology and Productive Innovation of the Nation (MINCYT), Argentine Republic; in the "Covid-19 Projects" category, having been selected in the catalog of innovative products, won the 1st. "Covid-19 Projects" position of the National Agency for Research and Technological Development and local innovation (R+D+i) dependent on MINCYT.The results showed, according to the analysis of the test bench, that the PMSM/IPM type synchronous motor used in the centrifugal fan, with the innovation of the reactance-inductive control in series plus the capacitor in parallel, reduces the power by 67% (Watts) and active energy consumption (kWh), performing 56% more mechanical work (Joules) on the fluid air (with a 50% reduction in carbon footprint). Which leads us to the following conclusion: it is possible to develop centrifugal fans that save electricity (kWh) without the need to resort to (1) the "Fan Affinity Law", nor (2) the use of variable speed drives (VDF) or frequency (which are devices with complex and expensive electronics). Which would bring an enormous saving of the cost of electrical energy.

To minimise environmental impact, avoid regulatory penalties, and improve competitiveness, energy-intensive manufacturing firms require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. Deep learning is widely touted as a superior analytical technique to traditional artificial neural networks, machine learning, and other classical time series models due to its high dimensionality and problem solving capabilities. Despite this, research on its application in demand-side energy forecasting is limited. We compare two benchmarks (Autoregressive Integrated Moving Average (ARIMA), and an existing manual technique used at the case site) against three deep learning models (simple Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)) and three machine learning models (Support Vector Regression (SVM), Random Forest, and K-Nearest Neighbors (KNN)) for short term load forecasting (STLF) using data from a Brazilian thermoplastic resin manufacturing plant. We use the grid search method to identify the best configurations for each model, and then use Diebold-Mariano testing to confirm the results. Results suggests that the legacy approach used at the case site is the worst performing, and that the GRU model outperformed all other models tested.

The radio activity in Wireless Sensor Networks (WSN) and Internet of Things (IoT) applications are the most common reason for power consumption. However, recognizing and controlling the factors affecting radio activity can be valuable for managing node power. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS that uses Clear Channel Assessments (CCA) to check radio status periodically. The time taken to check the radio in receive mode WakeUp, is one of the most important reasons for power consumption which in most the cases can lead to negative WakeUp in Radio Duty-Cycles and ContikiMAC especially. Here, we present a detailed analysis of idle listening time factors on the ContikiMAC. Then, we propose Light Weight CCA(LW-CCA) as an extension to ContikiMAC to reduce power consumption by reducing the radio check time in receive mode WakeUp’s, while maintaining up to 99% the Packet Delivery Rate (PDR). The simulation results show that the proposed method reduces significantly energy consumption in nodes compared to ContikiMAC and thus it helps maintain a high network performance.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

Solar energy is a renewable resources of energy which is broadly utilized and have the least pollution impact between the available alternatives of fossil fuels. In this investigation, machine leaening approaches of neural networks (NN), neuro-fuzzy and least squares support vector machine (LSSVM) are used to build the models for prediction of the thermal performance of a photovoltaic-thermal solar collector (PV/T) by estimating its efficiency as an output of the model while inlet temperature, flow rate, heat, solar radiation, and heat of sun are input of the designed model. Experimental measurements was prepared by designing a solar collector system and 100 data extracted. Different analyses are also performed to examine the credibility of the introduced approaches revealing great performance. The suggested LSSVM model represented the best performance regarding the mean squared error (MSE) of 0.003 and correlation coefficient (R²) value of 0.99, respectively.

Tapping panel dryness (TPD) syndrome is a complex disease of Rubber tree (Hevea brasiliensis L.) which causes cessation of latex drainage upon tapping of rubber tree. Rubber tree virus (RTV1) was identified as a novel pathogen associated with rubber tree and a potential causal agent of TPD. RTV1 is a monopartite RNA virus that is linear, non-enveloped and has a single-stranded (ss) positive RNA genome of approximately 6081 nucleotides and is composed of two major open reading frames (ORFs), ORF1 (polyprotein), and ORF2 (movement protein. This study aimed to investigate the possibility of rubber genome encoded tree microRNAs (miRNAs) as novel therapeutic targets against RTV1 using in silico algorithms. Mature rubber tree miRNAs are retrieved from the miRBase database and are used for hybridization of RTV1 using five different five different computational algorithms including miRanda, RNA22, RNAhybrid and psRNATarget. A total of eleven common rubber tree miRNAs were identified based on consensus genomic positions. The consensus of four algorithms predicted the hybridization sites of hbr-miR396a and hbr-miR398 at common locus positions 6676, 1840 respectively. To validate the prediction, secondary structures of the consensual rubber tree miRNAs and free energy of duplex binding were calculated using the RNAfold and RNAcofold algorithms respectively. We created a plot between rubber tree miRNAs and RTV1 ORFs by using Circos algorithm. In this study, we predicted eleven consensual rubber tree miRNAs. Among these miRNAs, hbr-miR398 was identified as the most effectual miRNA that may target the ORF1 gene of the RTV1 genome. The predicted data will be important in the development of rubber trees resistant to RTV1.

Issues related to safe and abundant energy production have been prominent in recent years. This is particularly tr ue when society considers how to increase the quality of life by providing low-cost energy to citizens. A significant concern of the Gulf Cooperation Council (GCC) relates to the environmental effects of energy production and energy use associated with climate change. Efforts to reduce fossil fuel use and increase the use of renewable energy, together with the price volatility of fossil fuels, have seriously impacted the economics of many of the oil-producing countries, particularly the Gulf States, which has led to efforts to make their economies more diverse and less dependent on oil production.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

The world is facing an energy crisis. Governments are seeking to provide universal energy access and guarantee energy security while trying to mitigate climate change. One possible solution is energy transitions towards low carbon energy systems. Among other things (physical infrastructure, public policy and regulatory enablers and knowledge and capacities) changes in the energy systems require a well informed and participative citizenship. Within this context the concept of energy literacy appears. Energy literacy is the understanding of how energy is generated, transported, stored, distributed and used, awareness about its environmental and social impacts and the knowledge to use it efficiently in the different sectors of the economy. This paper provides a systematic literature review in the Web of Science’s Core Collection. Most of the work done around energy literacy addresses its evaluation among different groups, particularly students at different levels, and the construction, application and evaluation of tools for improving energy literacy. Other frequently studied issues are the influence of energy literacy in decision making, its drivers and conceptual research about the topic. Energy enables citizens to effectively contribute to energy efficiency and sustainable development, nevertheless energy literacy is not strongly correlated to energy consumption habits.

The term sustainable energy is very familiar to all of us yet its exact definition or meaning has so far been vague. To date the widely adopted definition of sustainable energy has been inspired by the definition of sustainable development formulated more than 30 years ago in the Our Common Future - the UN’s Report of the World Commission on Environment and Development. The current definition conceals the true spirit of the Report and this has some ramifications. It raises the question as to whether we have put too much emphasis on attaining the future dimension of sustainability in the middle of the situation where the energy survivability is in fact the real issue in many parts of the world. In this paper the role of energy in sustaining livelihoods of low income communities is discussed. Existing definition of sustainable energy that the whole world seems to have embraced is looked at critically and its downsides exposed. The identified pillars of sustainable energy and the associated issues is discussed and the need for an additional pillar, i.e. affordability is discussed and called for. This paper will argue that global definition of sustainable energy seems inappropriate and should be jettisoned and a more realistic definition should be formulated, adopted and embraced at local (i.e. national or regional) level taking into account local attributes and factors. The current push for a transition from the reliance on conventional energy sources to ‘cleaner’ energy sources (generally associated with renewable energy) has further exacerbated the issue of energy affordability that has made the conditions even more dire for so many groups of the world population. In the midst of this situation, those who push for a rushed energy transition seem to be those who also produce unsustainably high carbon footprint but who can easily offset their carbon foot-print through the ‘net-zero’ concept.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

The Universe at last scattering is locally treated as an unbound gas. The internal kinetic energy of the gas effectively constitutes a scalar energy field. The gas’s adiabatic expansion is entropic, giving repulsive entropic pressure. Gas kinetic energy is converted into entropic energy gain (63%) and isoentropic work against gravity (37%) at a constant 63:37 ratio. A three-term expression of the gas’s Hubble parameter is derived and found to be exclusively dependent on its mass density. At last scattering, this model gives a Hubble constant that is 125% of the value found from the ΛCDM model. After partition of Universal mass into the cosmic web of galaxies and the intergalactic medium (IGM), expansion came mostly from the IGM, presently comprising about 84% of total Universal mass and 90% of its volume. The onset of star formation within the cosmic web increased the IGM’s kinetic energy through the action of starlight, giving free electrons as an additional repository. Many of these free electrons are suprathermal. Suprathermal energy from both electrons and protons comprises about half of the IGM’s total kinetic energy and is expressed in the ΛCDM model as “dark energy” Λ. Entropic pressure derives from thermodynamic laws not found within general relativity.

This article aims to assess the benefits of floor-slab insulation measures using extruded polystyrene (XPS) and polyisocyanurate (polyiso) insulation materials at various levels of insulation thicknesses for a detached residential building. The EnergyPlus simulation analysis was carried out within the seven energy zones (represented by eight locations) of South Africa in accordance with the South African national code for building energy efficiency (SANS10400-XA). The energy savings and payback periods due to use of the insulation over a lifecycle period of 50 years were assessed. Cape Town (zone 4) behaved differently from other locations and hardly benefitted from the application of floor-slab insulation measures. Generally, polyiso insulation performed better than XPS, for vertical gap insulation. For vertical gap insulation, lower insulation thicknesses required higher insulation depths to maximize energy savings. Similarly, lower insulation thicknesses required higher perimeter insulation widths to maximize energy savings, for the horizontal perimeter insulation method. The locations that benefitted most from vertical gap floor-slab insulation were Pretoria (zone2), Kimberley (zone6), Nelspruit (zone3), Fraserburg (zone7), Welkom (zone1), Mthatha (zone5), Ixopo (zone5H) and Cape Town (zone4) in that order. This order was almost similar with those for the horizontal perimeter floor-slab insulation and horizontal full floor-slab insulation methods.

Machine learning (ML) has found increasing use in research on energy conversion and storage technologies, in particular, so-called sustainable technologies. While often ML is used to directly optimize the parameters or phenomena of interest in the space of features, in this perspective, we focus on using ML to construct objects and methods that help in or enable the modeling of the underlying phenomena. We highlight the need for machine learning from very sparse and unevenly distributed numeric data in multidimensional spaces in these applications. After a brief introduction of some common regression-type machine learning techniques, we will focus on more advanced ML techniques which use these known methods as building blocks of more complex schemes and thereby allow working with extremely sparse data and also allow generating insight. Specifically, we will highlight the utility of using representations with sub-dimensional functions by combining the high-dimensional model representation ansatz with machine learning methods like neural networks or Gaussian process regressions in applications ranging from heterogeneous catalysis to nuclear energy.

Following an updated outlook of global energy production and utilization, we show through selected examples from both developing and developed countries how distributed generation from renewable energy sources, and from solar energy in particular, is the key solution to ending energy poverty across the world. Guidelines aimed at policy makers suggest a systems view of energy that will be instrumental in guiding the transition from fossil fuels to combustion-free renewable energy for all energy end uses.

This analysis focuses on identifying the most efficient and cost-effective method of supplying power to a remote site, exploring photovoltaics (PV) and small wind turbines as primary power sources, and evaluating battery banks and hydrogen storage fuel cell systems as potential storage options. The hydrogen storage system converts surplus renewable power into hydrogen through an elec-trolyzer, storing it for later use in a fuel cell when renewable sources produce less power, enabling efficient energy storage during peak production periods. A sensitivity analysis of wind speed and hydrogen subsystem cost was conducted to evaluate the hydrogen storage system's performance. The optimal system graph suggests that the hydrogen subsystem must significantly decrease in cost to rival the battery bank, and in most cases, both the hydrogen system and battery bank were recommended together, offering reliable and efficient power for the remote site. While the battery bank is presently the more feasible option for powering the remote site, continuous monitoring and evaluation of both systems, considering site location, energy needs, and available resources, are essential to determine the most suitable power supply approach as technology advances and costs evolve over time.

The water and wastewater sectors are energy-intensive, and so a growing number of utility companies are seeking to identify opportunities to reduce energy use. Though England’s water sector is of international interest, in particular due to the early experience with privatisation, for the time being very little published data on energy usage exists. We analyse telemetry data from Thames Water Utilities Ltd. (TWUL), which is the largest water and wastewater company in the UK and serves one of the largest mega-cities in the world, London. In our analysis, we (1) break down sectoral energy use into their components, (2) present a statistical method to analyse the long-term trends in use, as well as the seasonality and irregular effects in the data, (3) derive energy-intensity (kWh m³) figures for the system, and (4) compare the energy-intensity of the network against other regions in the world. Our results show that electricity use grew during the period 2009 to 2014 due to capacity expansions to deal with growing water demand and storm water flooding. The energy-intensity of the system is within the range of reported figures for systems in other OECD countries. Plans to improve the efficiency of the system could yield benefits in lower the energy-intensity, but the overall energy saving would be temporary as external pressures from population and climate change are driving up water and energy use.

Commercial buildings are a significant consumer of energy worldwide. Logistics facilities, and specifically warehouses, are a common building type yet under-researched in the demand-side energy forecasting literature. Warehouses have an idiosyncratic profile when compared to other commercial and industrial buildings with a significant reliance on a small number of energy systems. As such, warehouse owners and operators are increasingly entering in to energy performance contracts with energy service companies (ESCOs) to minimise environmental impact, reduce costs, and improve competitiveness. ESCOs and warehouse owners and operators require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. This paper explores the performance of three machine learning models (Support Vector Regression (SVR), Random Forest, and Extreme Gradient Boosting (XGBoost)), three deep learning models (Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)), and a classical time series model, Autoregressive Integrated Moving Average (ARIMA) for predicting daily energy consumption. The dataset comprises 8,040 records generated over an 11-month period from January to November 2020 from a non-refrigerated logistics facility located in Ireland. The grid search method was used to identify the best configurations for each model. The proposed XGBoost models outperform other models for both very short load forecasting (VSTLF) and short term load forecasting (STLF); the ARIMA model performed the worst.

Energy citizenship is increasingly receiving attention and highlights the transformation from passive to active energy consumers who are aware of and responsible for the energy transition. The topic is often associated with energy communities, which are regarded as organizations that allow citizens to directly engage in energy and broader sustainability initiatives. The objective of the article is to examine the extent of public and private engagement in the energy transition among cooperative members as well as the propensity of energy communities to promote empowerment and inclusivity. To this end, we employ a mixed-methods approach, involving a sample of 5402 participants and 20 qualitative interviews in two prominent energy cooperatives in Europe, Ecopower in Flanders and è nostra in Italy. Our results show that although a small group of members demonstrate strong and active engagement, the majority of members prefer to engage informally, while still benefitting from the empowerment provided by their cooperative. Interestingly, one subset of members is more closely aligned with the role of financial investors. Eventually, flexibility in defining and framing expectations of member engagement can play a crucial role in promoting inclusivity within energy communities, especially by bringing closer those relatively less familiar with the issue.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

Large-scale integration of solar energy technologies in Rome’s built environment epitomizes the needed general adoption of distributed generation via functionalization of buildings of all size and end use across the world, to become active energy generators and no longer energy users only. This paper identifies selected technology solutions and critical policy and educational initiatives to effectively achieve within the next decade (2018-2027) the widespread uptake of decentralized solar energy systems in the built environment on a global scale.

Small modular reactors (SMR) (&lt;300 MW) offer a potentially attractive nuclear energy option for the middle-east region (MER). Currently, the MER uses a significant amount of fossil fuel to process heat applications such as water desalination and in petroleum refineries and chemical plants, besides generating electricity. SMR technologies represent an opportunity to meet future energy demand in the MER. This paper discusses issues related to the future development and use of SMR technology in nuclear-renewable hybrid energy systems for application in the middle east. SMRs have also been examined as part of a resilient hybrid energy system that combines nuclear energy with renewable energy and traditional fossil energy to produce chemicals, fuels, and electricity. This paper presents the results of a techno-economic analysis of a Nuclear-Renewable-Conventional Hybrid Energy System. The paper concludes that SMR technology will be an essential feature of future hybrid energy systems for the MER.