A two-way coupled model between polydisperse particle phases with compressible gases and a density-based coupling implicit solution method combining the third-order MUSCL with QUICK spatial discretization scheme and the second-order temporal discretization scheme are constructed based on the discrete-phase model (DPM) and the stochastic wander model (DRWM) in the Eu-lerian-Lagrangian framework in conjunction with a unitary particulate source (PSIC) approach and the SST k-ω turbulence model. The accuracy of the numerical prediction method is verified using previous supersonic nozzle gas-solid two-phase flow experiments. Numerical simulation of two-phase jet of dry powder extinguishing agent gas with pilot-type supersonic nozzle was carried out to analyze the influence of geometrical parameters such as length ratio rL and area ratio rA of main nozzle on the two-phase flow field as well as on the jet performance indexes such as particle mean velocity vp,a, velocity inhomogeneity Φvp, particle dispersion Ψp, particle mean acceleration ap,a and so on. By analyzing the parameters, we indicate the requirements for the combination of jet performance metrics for different flame types such as penetrating, spreading, and dispersing.

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

The flowability of a powder is a characteristic dependent on both the particle ensemble's physical properties as well as the testing equipment and conditions. In powder bed additive manufacturing processes (SLM, EBM), flowability can be used to predict the quality of the deposited powder layer. However, how representative flowability is for the powder bed layer quality is not always clear.In this work, we compared several steel powders, as well as different testing methods. Each powder had an individual combination of composition or particle size distribution. Furthermore, the flowability testing equipment and methods were selected according to standards (Tap density, Hall flow) or referring to the published literature (angle of repose, FT4 Powder Rheometer). After measuring the flowability of different samples for each testing method, we created a database to evaluate a first correlation between the different testing methods. Finally, with a Powder Rheometer, we investigated for one sample some flow properties as function of different particle size distributions.

The basis of the work of electroencephalography (EEG) is the registration of electrical impulses from the brain or some of its individual areas using a special sensor/electrode. This method is used for the treatment and diagnosis of various diseases. The use of wet electrodes in this case does not seem viable, for several well-known reasons. As a result of this, a detailed analysis of modern EEG sensors developed over the past few years is carried out, which will allow researchers to choose this type of sensor more carefully and, as a result, conduct their research more competently. Due to the absence of any standards in the production and testing of dry EEG sensors, the main moment of this manuscript is a detailed description of the necessary steps for testing a dry electrode, which will allow researchers to maximize the potential of the sensor in the various type of research.

Current dry powder formulations for inhalation deposit a large fraction of their emitted dose in the upper respiratory tract where they contribute to off-target adverse effects and variability in lung delivery. The purpose of current study is to design a new formulation concept that more effectively targets inhaled dry powders to the large and small airways. The formulations are based on adhesive mixtures of drug nanoparticles and nanoleucine carrier particles prepared by spray drying of a co-suspension of leucine and drug particles from a nonsolvent. The physicochemical and aerosol properties of the resulting formulations are presented. The formulations achieve 93% lung delivery in the Alberta Idealized Throat model that is independent of inspiratory flow rate and relative humidity. Largely eliminating URT deposition with a particle size larger than solution pMDIs is expected to improve delivery to the large and small airways, while minimizing alveolar deposition and particle exhalation.

Use of porous titanium (Ti) and Ti alloys in orthopedic implants or in light structures requires processing routes that could generate an as-much-as possible control in the pores amount, shape, size and connectivity. In this work, a colloidal approach to the processing of Ti porous structures by the inside foaming of a porogen into a gelled high solid content aqueous suspension of Ti powders, is presented. The prepared slurries contained different amounts of Methyl Cellulose (MC) as gelling agent (8, 10 and 12 g/L) and ammonium bicarbonate (BA) as porogen (15, 20, 25 wt. %). The gel-casted samples were heated at mild temperatures ranging (60, 70 and 80 °C) to promote the gelation and produce, at the same time, the porosity by the thermal decomposition of the ammonium bicarbonate. Different structures are obtained depending on the combination of the study variables

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

The horizontal storm structure surrounding lightning ignited wildfires is examined using Vaisala’s National Lightning Detection Network (NLDN), NCEP’s Stage IV gauge corrected radar precipitation mosaic, and the US Forest Service’s Fire Occurrence Database. Though lightning flash density peaks strongly around fire ignitions on the instantaneous 1 km scale, on the hourly 10 km scale both the lightning and precipitation peaks are typically offset from fire ignitions. Lightning density is higher and precipitation lower around ignition points compared to non-ignition points. Both regression and horizontal distributions are consistent with the claim that positive flashes have a stronger association with ignition than negative flashes, but the statistical significance remains ambiguous

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

The term STODS (Surgical Temporary Ocular Discomfort Syndrome) has been coined to describe the ocular surface perturbations induced by surgery. As one of the most important refractive elements of the eye, Guided Ocular Surface and Lid Disease (GOLD) optimization is fundamental to success in achieving refractive outcomes and mitigating STODS. Effective GOLD optimization and the prevention/treatment of STODS, requires an understanding of the molecular, cellular and anatomic factors that influence ocular surface microenviroment and the associated perturbations induced by surgical intervention. By reviewing the current understanding of STODS etiologies, we will attempt to outline a rationale for a tailored GOLD optimization depending on the ocular surgical insult. With a bench to bedside approach, we will highlight clinical examples of effective GOLD perioperative optimization can mitigate STODS deleterious effect on preoperative imaging and postoperative healing.

Xerostomia is a subjective symptom of dry mouth resulting from various causes, including side effects of medication, systemic disorders, radiation, and Sjögren’s syndrome. Recently, the number of patients afflicted with xerostomia has increased due to an increase in the elderly population and patients on medication.; (2) Methods: A systematic approach is required to determine the etiology and management of xerostomia. This review summarizes recent literatures on the diagnosis and management of xerostomia.; (3) Results: A patient with xerostomia experiences difficulty in chewing, swallowing, speaking, tasting, and maintaining oral hygiene. Xerostomia and hyposalivation are uncomfortable side-effects in many patients. Assessing the function of the salivary gland is essential for selecting an appropriate treatment, improving symptoms, and preventing oral complications. Also, a more systematic approach is required to differentiate the subjective symptoms of the patient from the objective hyposalivation.; and (4) Conclusions: Although there is no standardized treatment for xerostomia, doctors need to endeavor and adapt the various treatments of xerostomia, to unearth the optimal treatment required for the patient.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

Human Insulin (HI) is a well-characterized natural hormone which regulates glycose levels into the blood-stream and is widely used for diabetes treatment. Numerous studies have manifested that despite significant efforts devoted to structural characterization of this molecule and its complexes with organic compounds (ligands), there is still a rich diagram of phase transitions and novel crystalline forms to be discovered. Towards the improvement of drug delivery, identification of new insulin polymorphs from polycrystalline samples, simulating the commercially available drugs, is feasible today via macromolecular X- ray powder diffraction (XRPD). This approach has been developed and is considered as a respectable method, which can be employed in biosciences for various purposes such as observing phase transitions and characterizing bulk pharmaceuticals. An overview of structural studies on human insulin complexes performed over the past decade employing both synchrotron and laboratory sources for XRPD measurements, is reported herein. This review aims to assemble all recent advances in diabetes treatment field in terms of drug formulation, verifying in parallel the efficiency and applicability of protein XRPD for quick and accurate preliminary structural characterization in large scale.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Abstract: Rotavirus (RV) it’s the agent of one of the main causes of severe viral gastroenteritis in the pediatric population, being responsible for a significant portion of deaths related to diarrhea among children under five years. RV are identified as a potential reference pathogen and it is known that the persistence and infectivity of the viral particles can be related to environmental factors. The aim of the study was to identify and correlate the presence of Rotavirus in collective and individual water sources (deep tubular wells, shallow tubular wells, shallow dug wells, springs, surface water, rainwater stored in cisterns and water trucks that were collected from surface water) of rural communities in the state of Goiás, with the seasons in which the collections were made (rainy and dry season). For this, 86 water samples in the dry period and 160 samples in the rainy period were collected. Concentration of water samples, extraction of viral genetic material, cDNA synthesis and molecular tests (qPCR) were performed. When analyzing the presence of RV in the samples in relation to the period studied, RV was found to be more prevalent in the dry season (54.7%) than in the rainy season (20%), showing a strong statistical association with the dry season (p-value < 0.001). The proportion of positive samples in the dry period, considering the type of source, resulted in higher in Shallow dug wells (p-value <0.001), higher in surface waters (p = 0.001) and higher in spring water (p-value = 0.02). The presence of pathogenic microorganisms in water is a public risk problem, enabling the emergence of outbreaks, endemics and epidemics. In the present research, there was an association among the presence of Rotavirus and the dry period of the year, when compared to the rainy period. Describing or identifying the seasonal behavior of pathogens is important for prevention and attention to water treatment and help in the monitoring of the virus in the water sources.

Protein malnutrition is present in developing countries but also in developed ones, due by the actual eating habits with insufficient protein intake, in addition to this it is estimated by the Food and Agricultural Organization of the United Nations an increase of world population of 9.1 billion people in less those 30 years, posing the challenge of nourish the mankind. There are different strategies to afford this challenge, one of the most promising ones is to approach novel protein sources like plants, microorganisms, and insects from dry lands.

The outbreak of COVID-19 in 2020 caused significant disruptions to global shipping and the world economy. This paper aims to investigate the impact of the pandemic on global shipping by analyzing the Baltic Dry Index (BDI). The BDI is a metric that reflects the worldwide shipping costs and directs related to supply and demand conditions, making it an indicator of economic production. The study utilizes data from 2019 to 2021, before and after the outbreak of COVID-19, and considers 13 independent variables, including raw materials, energy, stock market indexes, global port calls, and confirmed COVID-19 cases to investigate how to influent the BDI. The study employs stepwise regression to select variables and build models before and after the pandemic. The findings reveal that the key factors affecting the freight index BDI before the outbreak are: international scrap steel prices, iron ore prices, and the Commodity Research Bureau Index. However, after the COVID-19 outbreak, the factors affecting the BDI changed to the Shanghai Index, global port calls, and the number of confirmed COVID-19 cases.

Although the dry ice method used to synthesize exfoliated graphite/graphene is little known and used, it has significant advantages over others: it is low cost, simple, and a large quantity of material can be obtained using some inorganic and highly available acids (which can be reused). Despite the above advantages, the main reason for its incipient development is the resulting presence of magnesium oxide in the final product. In the present work, three different treat-ments were tested to remove this remnant using some acid chemical leaching processes, making use of hydrochloric acid, aqua regia, and piranha solution. Based on the experimental evidence, it was found that using aqua regia and combining the leaching process with mechanical milling was the most efficient way of removing such a remnant, the residue being only 0.9 wt.%. This value is low when compared to that obtained with the other acid leaching solutions and purifi-cation process (2.8 - 29.6 wt.%). A mandatory high-energy mechanical milling stage was neces-sary during this treatment, in order to expose and dissolve the highly insoluble oxide without secondary chemical reactions on the graphenes. High-energy mechanical milling is an effective route to exfoliate graphite/graphene, which allows the magnesium oxide to be more susceptible to acid treatment. The obtained surface area was 504 m2g-1; this high value resulting from the in-tense exfoliation can potentiate the use of this material for a wide variety of applications.

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

The experiment was conducted in three locations Jari, Chefa and Sirinka of Eastern Amhara to select the best performing varieties, in terms of biomass yield, chemical composition, haulm yield, seed yield and other agronomic characteristics of Glycine max (L.) Merrill grown under the rain- fed condition of lowland areas of Eastern Amhara in a randomized complete block design with tree replications. Twelve released soybean varieties were Afgat ,Belesa-95, Boshe , Cheri , Dhidhessa, Gishama , Gizo, Korme, Pawe-03, katta, Wegayen and Wollo were used as a treatments. The seeds were planted in 40 cm between rows and 10 cm between plants on a plot size of 3.2m*4m. Spacing between blocks and plots were 1 and 0.5m, respectively. The seed rate was 60 kg/ha and a fertilizer rate 100 kg/ha NPS was applied during seed planting. The combined analysis of variance over two years at location Jari for dry matter yield of varieties Afgat, Gizo, Pawe-03, Wogayen and Wollo were significantly higher as compared to other soybean varieties. The combined analysis across locations at Jari and Sirinka (2019-second year) showed that varieties Afgat, Gishama, Gizo, Pawe-03, Wogayen and Wollo had higher dry matter yield and varieties Gishama (3.97 t/ha), Gizo (3.60 t/ha), Pawe-03 (4.04 t/ha) and Wogayen (3.36 t/ha) had higher haulm yield as compared with other varieties. The combined analysis across locations at Jari and Sirinka (2019) showed that varieties Pawe-03(2951 kg/ha), Gizo (2862 kg/ha), Afgat (2859 kg/ha), Gishama (2654 kg/ha),Wollo (2461 kg/ha) and Wogayen (2404 kg/ha) had higher seed yield as compared with other varieties. The variety Wollo gave higher crud protein content in two locations (Jari and Sirinka) .Therefore, varieties Afgat, Pawe-03 and Wollo were recommends for the given areas of Jari , Chefa, Sirinka and could be produced in similar environments for the best of produced optimal amount of dry matter, haulm and seed yield and good protein supplement for production of ruminants.Thus, further researches will be needed to investigate on the utilization of livestock.

This study investigated dry reforming of methane with combined catalysts supported on γ-Al2O3 support doped with 3.0 wt. % TiO2. The physicochemical properties of all the catalysts were determined by inductively-coupled plasma/mass spectrometry metal analysis, nitrogen physisorption, X-ray diffraction, temperature programmed reduction/desorption, thermogravimetric analysis, and scanning electron microscopy. The addition of CeO2 and MgO to Ni strengthened the interaction between the Ni and the support. The catalytic activity results indicated that the CeO2 and MgO addition to Ni did not do much in retarding carbon deposition, but they improved the activity of the catalysts. Among the tested catalysts, it was found that the catalyst with the composition of 5.0 wt % NiO-10.0 wt % CeO2/3.0 wt %TiO2-γ-Al2O3 resulted in the highest CH4 and CO2 conversion with H2/CO mole ratio close to unity. The optimum reaction conditions in terms of reactant conversion and H2/CO mole ratio were achieved by varying space velocity and CO2/CH4 mole ratio.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

Under the influence of various factors, the bronze ware unearthed by archaeology has various diseases of different degrees, and the mineralization problem is more prominent. The physical properties of mineralized bronzes have been destroyed, and the whole is loose and fragile, which is in urgent need of reinforcement and protection. Common reinforcement and protection materials mainly consider surface sealing, matrix bonding reinforcement and penetration reinforcement. Considering the low matrix strength and complex disease types of fragile bronzeware, it is difficult to achieve targeted protection with commonly used reinforcement and protection materials. In view of the problems such as poor permeability and easy discoloration of commonly used protection materials, this paper uses self-developed reinforcement and protection material AMC to compare its reinforcement and protection performance with B72, which has a high comprehensive evaluation on the performance of commonly used reinforcement and protection materials. The matrix strength was increased, and the appearance intervention degree was less than B72.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Cold gas dynamic spray (CS) is a unique technique to deposit material using high strain rate solid state deformation. A major challenge for this technique is its dependence on the powder properties and lack of standards to assess them between lots and manufacturers. The motivation of this research was to understand the variability in powder atomization techniques for stainless steel powders and their subsequent properties for their corresponding impact on CS. A drastic difference (~30%) was observed in deposition efficiencies (DE) of unaltered, spherical, and similar sized stainless steel (316) powders produced using centrifugal (C.A) and traditional gas atomization (G.A) techniques. The study highlights more on differences on precursor level. Using recent advancements in large scale statistical measurements like laser diffraction shape analysis, µCT scanning, traditional methods like EBSD, nano-indentation, an attempt is made to understand the powder property. Insights on powder size and shape are documented. Significant differences were observed between C.A and G.A powders in terms of grain size, fraction of higher angle grain boundaries (HAGB) and nano hardness. The outcomes of this study would be helpful to understand the commercialization of the cold-spray process for bulk manufacturing of powder precursors

One of the areas of research on materials for thin-film solar cells focuses on replacing In and Ga with more earth-abundant elements. In that respect, chalcostibite (CuSbS2) is being considered as a promising environmentally friendly and cost-effective photovoltaic absorber material. In the present work, single CuSbS2 phase have been synthesized directly by a short duration (2 h) mechanochemical synthesis step starting from mixtures of elemental powders. X-ray diffraction analysis of the synthesized CuSbS2 powders revealed a good agreement with the orthorhombic chalcostibite phase, space group Pnma, and a crystallite size of 26 nm. Particle size characterization revealed a multimodal distribution with a median diameter ranging from of 2.93 m to 3.10 m. The thermal stability of the synthesized CuSbS2 powders was evaluated by differential thermal analysis. No phase change was observed by heat treating the mechanochemically synthesized powders at 350 C for 24 h. By UV-VIS-NIR spectroscopy the optical bandgap was determined to be 1.41 eV, suggesting that the mechanochemically synthesized CuSbS2 can be considered suitable to be used as absorber materials. Overall, the results show that the mechanochemical process is a viable route for the synthesis of materials for photovoltaic applications.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Laser Cladding is one of the leading processes within Additive Manufacturing technologies, a fact which has concentrated an important amount of effort on its development. In regard to the latter, the current study aims to summarize the influence of the most relevant process parameters in the laser cladding processing of single and compound volumes (solid forms) made from AISI 316L stainless steel powders and using a coaxial nozzle for deposition. Process speed, applied laser power and powder flow are considered to be the main variables affecting laser cladding in single clads, meanwhile overlap percentage and overlapping strategy become also relevant when dealing with multiple clads. By means of setting appropriate values of each process parameter, the main goal of this paper is to develop a processing window in which a good metallurgical bond between the delivered powder and substrate is obtained, trying simultaneously to maintain processing times in their lowest value possible. Conventional metallography techniques were performed on the cross sections of the laser tracks to measure the effective dimensions of clads for dilution analysis, height and width for the values of overlap between contiguous clads and layers, and also to analyze them for physical defects such as porosity and cracks. The resulting solid piece was 8 mm high at 800 mm/min.

Gabapentin (GBP) was originally developed as a potential agonist for Gamma-Amino-Butyric-Acid (GABA) receptors, aiming to inhibit the activation of pain-signaling neurons. Contrary to initial expectations, it does not bind to GABA receptors. Instead, it exhibits several distinct pharmacological activities, including: (1) binding to the alpha-2-delta protein subunit of voltage-gated calcium channels in the central nervous system, thereby blocking the excitatory influx of calcium; (2) reducing the expression and phosphorylation of CaMKII via modulation of ERK1/2 phosphorylation; (3) inhibiting glutamate release and interfering with the activation of NMDA receptors; (4) enhancing GABA synthesis; (5) increasing cell-surface expression of δGABA_A receptors, contributing to its antinociceptive, anticonvulsant, and anxiolytic-like effects. Additionally, GBP displays (6) inhibition of NF-kB activation and subsequent production of inflammatory cytokines, and (7) stimulation of the purinergic adenosine A1 receptor, which supports its anti-inflammatory and wound-healing properties. Initially approved for treating seizures and postherpetic neuralgia, GBP is now broadly used for various conditions, including psychiatric disorders, acute and chronic neuropathic pain, and sleep disturbances. Recently, as an eye drop formulation, it has also been explored as a therapeutic option for ocular surface discomfort in conditions such as dry eye, neurotrophic keratitis, corneal ulcers, and neuropathic ocular pain. This review aims to summarize the evidence supporting the molecular effects of GBP, with a special emphasis on its applications in ocular surface diseases.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

We studied the capacity of glutathione and a specific inactivated dry yeast rich in glutathione to protect white grape must from browning compared to using sulphur dioxide. The results indicate that sulphur dioxide drastically reduces the oxygen consumption rate, protects hydroxycinnamic acids from oxidation and prevents grape must against browning even in the presence of laccase. Glutathione, pure or in the form of a specific inactivated dry yeast rich in glutathione, also reduces the oxygen consumption rate but to a lesser extent than sulphur dioxide. It favours the formation of GRP from hydroxycinnamic acids and effectively protects grape must against browning in healthy grape conditions. Nevertheless, in the presence of laccase it was not effective enough. Therefore, both forms of glutathione can be considered as interesting alternative tools to sulphur dioxide for preventing browning in white grape must, but only when the grapes are healthy.

Dry eye disease (DED) is one of the most common eye diseases. There is at least one DED patient in almost every five people. AI-based research methods increasingly become the focus of DED diagnosis research. This study utilizes a systematic review method on DED AI-based diagnosis. 2112 unduplicated records are extracted from Google Scholar, Web of Science (WOS), PubMed, China National Knowledge Infrastructure (CNKI), and Scopus databases. The most contributed countries, institutions, authors, journals, references, and disciplines are recognized. Keyword distribution and hot topics are identified. Popular databases of ophthalmic images, videos, and electronic demographic medical records are discussed. The DED diagnosis, classification, and grading criteria are identified. The major diagnosing methods are clustered, compared, and investigated. Findings show that diagnosing method research could be classified into three categories based on the relationship between AI techniques, which are (1) ground truth and/or comparable standards for AI DED diagnosis (TBUT, S Ⅰ T, TMH, and OSDI), (2) potential methods for AI-based methods have a great advantage(DED detection based on meibometry Images, CASPs, IVCM Images, OCT Images, blink videos and ultrasonic imaging), (3) and the potential direction and supplemented methods for AI-based DED detection (DED detections based on tear osmolarity, proteomic analysis, TCM and demographic information). AI-based approaches based on digital ophthalmologic images play an important role in early screening. Challenges and future perspectives are discussed at the end of this article, academically and practically.

Dry intrusion is an important mid-latitude atmosphere phenomenon within the upper troposphere and lower stratosphere. It is always found to be related to the cyclogenesis, rainstorm, as well as convection generation and precipitation enhancement. Since the atmosphere environment for any of these above-mentioned weather is terribly complicated, those preexisting popular schemes which takes no account of water vapor may not suitable for detecting the dry intrusion related to these weathers. With regard to the merits and demerits of the current preexisting schemes, a new scheme based on Fengyun-2E geo-stationary satellite data is presented in this study to detect the atmospheric dry intrusion. The scheme is set up based on the statistical relationship between water vapor at high level troposphere, the general moist potential vorticity, ozone concentration and upper-level jet. After using the total amount of ozone and ozone profile operational products retrieved by Fengyun-3 Polar Orbiting Meteorological Satellites and the potential vorticity calculated by ECMWF Interim data for validation, this scheme is applied to analyze two typical middle-latitude weather processes. One is the famous Beijing extreme rainfall of 21 July 2012 and the other is a hailstorm occurred on the eastern China during March 19, 2014. A good application effect in both cases suggests that our new method of detecting dry intrusion is feasible and can be helpful in middle-latitude disastrous weather monitoring and forecasting.

Camel milk occupies a pivotal and essential position in the dietary customs of individuals residing in semi-arid and arid areas. Historically, the promotion and distribution of camel milk have been negligible, primarily due to the absence of processing facilities in areas where camels are raised. Consequently, the consumption of untreated camel milk has been predominantly limited to nomadic households. However, owing to its exceptional medicinal properties and health-enhancing effects, a substantial surge in the global demand for camel milk and its derivatives has been observed over the past two decades. This growing demand has prompted the dairy sector to introduce a diverse range of camel milk products, which are distinguished by their enhanced nutritional and functional properties. In contrast to products derived from bovine milk, the current market offers only a limited selection of food items sourced from camel milk. Recent advances in food processing technologies have enabled the production of an array of both dairy and non-dairy products derived from camel milk. This includes a variety of items such as powdered milk, cheese, yogurt, ice cream. Moreover, in certain regions, camel milk is incorporated into customary cuisine, serving as a key ingredient in local culinary practices like fermented milk, camel milk tea, or as a fundamental component in various meals. This review underscores the possibility of transforming camel milk into a range of dairy products by addressing its intrinsic functional constraints. This objective can be realized by adjusting the processing parameters and modifying its chemical composition through enrichment techniques. Furthermore, further research avenues may focus on enhancing product quality and exploring innovative processing techniques.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

Punica granatum (PG) or Pomegranate is a bush, having many trunks and often get taller 1.8 to 4.7m long and their leaves are shiny and fleshy, approximately 7 to 8cm in length. Traditionally, it is used in diarrhea and dysentery due to its strong constricting property. Punica Granatum covering used in dysentery, diarrhea, piles, bronchitis. It is also used to minimize the risk of heart disease. The peel extract of Punica Granatum contain methanol and their dried peels has antidiarrheal venture, also help in wound healing activity. Peels of the pomegranate also holds around 60% of the fruit and they contain different types of ingredients including ellagitannins and proanthocyanidin compounds and minerals such as calcium, phosphorus, magnesium, potassium, flavonoids and sodium. Some animals were found in different local areas with both acute and chronic diarrhea. The condition of these animals were quite miserable because of dehydration and loss of electrolytes in the body cells of the animals. They were unable to move due to seriousness of the disease. 8 grams of PG Peel Powder mixed with 1 liter of water, 2 g of PG Peel Powder mixed with 250 ml water and 8 g of PG Peel Powder mixed with 1 liter of water were administrated orally by using sterilized bottles to the selected three cases. 3 days after the administration of different doses, all cases of diarrheal animals show a significant recovery. The condition of the animals seem to be healthier. Before administration of the pomegranate peel powder extract, all three cases had weak body structure due to diarrhea. Watery stool that may be yellow in color and mucus was also evident in the stool, due to this reason the patient calf was weak and depressed. In sometimes they also show unconsciousness and blood glucose levels seem to be reduced from the normal level.

The concept of the protein powder dispenser was developed on the basis of the results of analyses, studies and customer requirements. The dispenser was assembled using SolidWorks software, which consists of 63 elements, 14 of which are unique parts that are not available on the market. Each part of the dispenser was carefully designed to be injected into the plastic compound. Polypropylene is the perfect material for this dispenser as it is low density, waterproof, insoluble and extremely resistant to tension and bending. High purity propylene polymer can be processed into a tough, rigid and lightweight plastic with relatively low manufacturing costs, replacing expensive materials. The authors' original contributions are the design and manufacture of a dosing device for protein powder, adjustable in 3 heights to be able to dose in containers of different sizes; the design and integration of a mechanism with a precise dosing system, the components being designed so that the parts in contact with the shaft filled with protein powder form a perfectly closed space; the design and integration of the mechanism for adjusting the height of the dispenser.

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

This study used eco-friendly materials known as Periwinkle Shell Powder (PSP) in stabilizing the engineering properties of lateritic soil. Preliminary test was performed on the un-stabilized lateritic soil for the purposes of identification and classification (natural moisture content, liquid limits, plastic limits, and plasticity index). The engineering tests were conducted on the lateritic soil stabilized with additions of (2, 4, 6, 8 and 10 %) PSP and OPC respectively. The result showed that cement gave a progressive increase in the Maximum Dry Density (MDD) of the lateritic soil from 1875 kg/m3 (2 %) to 2294 kg/m3 (10 %) respectively. This represents 22 % increase in the MDD from the un-stabilized state. For PSP, the Maximum MDD was attained at 6 % (1974 kg/m3), representing 5.3 % increase in MDD of the soil from the un-stabilized state. For both stabilizing agent, the Optimum Moisture Content (OMC) increases from 13.65 % to 13.83 % and from 11.72 % to 14.41 % for Cement and Periwinkle Shell Powder respectively. PSP recorded an increase of 5.6 % of CBR value compared with OPC that recorded an increase of 34 % CBR value. The study therefore concluded that Periwinkle Shell Powder (PSP) could be considered as good stabilizer for clayey or lateritic, and its uses as a stabilizer could also provide a big relief to the environmental pollution caused by its indiscriminate dumping.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels (0-20%), 75‰ salinity produced consistently favorable results in cell count (13.08 x 103 ± 1.41 x 103 cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 9.75 ± 0.01 µg/L, chlorophyll b = 12.36 ± 0.03 µg/L), and desalination (9.32 ± 0.47 % reduction). Therefore, 75‰ salinity level was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 103 ± 535.22 cells/mL), with dry biomass weight being statistically extremely different (higher) than the expected (4.21 ± 0.02 g/L) (p&lt;0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 9.54 ± 0.2 µg/L, chlorophyll b = 12.81 ± 0.51 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Despite this, the microalgae thrived in high salinity conditions. These findings point to further study into the mechanics of salt build-up within cells, which might lead to successful desalination technologies. Dunaliella salina adaptation to high salinity settings suggests its possible usage in natural pools or soils that are normally inappropriate for traditional production, giving a chance for enterprises to function in rough extreme salinity conditions.

The experiment was conducted to evaluate the effect of seed and fertilizer rates on biomass yield and other agronomic treats of two oat varieties (Bona-bas and Bate) at the Kuyu sub-site of Fitche Agricultural Research Center in 2022. Four levels of Nitrogen fertilizer rates (0, 23, 46, and 69 kg ha-1) and three levels of seed rates (60, 80, and 100 kg ha-1) with two oat varieties (Bona-bas and Bate) were using randomized complete block design in factorial arrangement with three replications. Soil samples before and after were collected and analyzed. The analysis of soil samples before planting indicated that the soil pH was strongly acidic (5.16) and after harvest, it raised to a strongly acidic level (5.29). The interaction effect of varieties, seed rates, and fertilizer rates showed highly significant (p<0.001) variation on the number of tillers per plant, leaf area per plant, leaf-to-stem ratio, fresh biomass yield, dry matter yield, days to maturity, and seed yield. The treatment combination of Bona-bas: FR46:SR100 has produced the highest dry matter yield (5.1 t/ha), followed by Bona-bas: FR46:SR60 and Bona-bas: FR69:SR80 which produced the same value of 4.9 t/ha dry matter yield. This study recommends that for the better agronomic performance of oat varieties, 46 kgha-1 N of fertilizer with 60 kgha-1 of seed rate is preferable to use by farmers in the study area and other areas having similar agroecologies and soil types. In addition, it is essential to conduct the year-over location to confirm the present findings and the result needs to be supported with animal evaluation trials.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

Beef dry aging consist in a selection of unpackaged primal cuts that are placed in a refrigerator room with controlled environment for several weeks. The goals are the concentration of flavor, like nutty and beefy and tenderness improvement. In this study it was intended verify the microbiological and physicochemical behavior and the meat sensorial perception during a process example of meat dry aging. Twelve beef loins were selected for 90 days of dry aging and placed in a refrigerator room with average temperature, relative humidity and forced air 3.17 ± 0.68 °C, 60.65 ± 4.23 % and 0.5-2 m/s, respectively. On 1, 14, 21, 35, 60 and 90 days of dry aging, were taken two samples, crust and lean meat for microbiological counts, pH, aw, color L*a*b* and sensorial analysis. During drying, there weren´t any pathogenic bacteria counts and the average counts were higher for the crust. The aw and pH had an average of 0.98 ± 0.02 and 5.77± 0.015, with a slightly decrease and increase respectively (P&lt;0.05) along aging days. The dry aging process practices, with room refrigeration at RH&lt;65.00% and temperature &lt;4.00 °C can be the reason for aw&lt;0.98 and meat pH&lt;6.00 and therefore for the absence of pathogenic bacteria. The lower microbial counts on the lean meat and the overall acceptability assessed by the sensory panel confirm the importance of the good trimming and storage practices for the dry aged beef.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

Once on Mars, maintenance and repair will be crucial for humans as supply chains including Earth andMars will be very complex. Consequently, the raw material available on mars must be processed and used. Factors such as the energy available for material production play just as important a role as the quality of the material that can be produced and the quality of its surface. With the aim of developing and technically implementing a process chain that meets the challenge of producing spare parts from oxygen-reduced Mars regolith, this paper addresses the issue of low-energy handling. Expected statistically distributed high roughnesses of sintered regolith analogs are approximated in this work by parameter variation in the PBF-LB/M process. For low-energy handling, a dry-adhesive microstructure is used. Investigations are carried out to determine the extent to which the rough surface resulting from the manufacturing process can be smoothed by deep rolling in such a way that the microstructure adheres and enables samples to be transported. For the investigated AlSi10Mg samples (12 mm x 12 mm x 10 mm), the surface roughness varies in a wide range from Sa 7.7 µm to Sa 64 µm after the additive manufacturing process, pull-off stresses of up to 6.99 N/cm² could be realized after deep rolling. This represents an increase in pull-off stresses by a factor of 392.94 compared to the pull-off stresses before deep rolling, enabling handling of even larger specimens. It is noteworthy that specimens with roughness values that were previously difficult to handle can be treated post-deep rolling, indicating a potential influence of additional variables that describe roughness or ripples and are associated with the adhesion effect of the microstructure of the dry adhesive.

In many tropical regions, national forests plantations programs have been promoted. Those plantations contribute frequently to habitat changes. However, it is unclear associated effects on habitat fragmentation and landscape connectivity. From 2008 to 2018, we examined plantation and deforestation data base of Manabí province (Ecuador) for assessing fragmentation and connectivity. At regional scale, forest plantations had a significant effect on land uses changes and fragmentation during the study period. Forests decreased from 33.7% to 32.45% between 2008 and 2018 in the study area, although other natural land uses, mostly shrubs, increased almost double (from 2.4% to 4.68%). Most of the deforestation affected native forests during this period, and most of reforested and afforested areas in 2018 covered former agricultural land. In this period, fragmentation data shows a decrease in the number of patches and an increase in patch average size. When considering reforestation, deforestation was higher than the afforested area (58 km2 of difference) increasing the number of patches but with smaller size. The scenarios that presented better connectivity were those where forest areas increased: avoiding deforestation and considering reforestation. Those scenarios had in general a higher number of links and distance. Regionally, the avoiding deforestation scenario increased connectivity for Puma yagouaroundi in the west part of the Manabí province. On the other hand, for the reforested scenario, the number of links also increased on central and extreme northeast areas. Our findings suggest that plantations may contribute to conservation thanks to an increase in forest plantations connectivity between fragmented patches.

Dry eye disease (DED) most commonly caused by evaporative subtypes and mainly induced by meibomian gland dysfunction (MGD). Intense pulsed light (IPL) combined with meibomian gland expression (MGX) is noninvasive treatment for improvement of ocular discomfort symptoms and MGD. In this prospective study between November 2020 and May 2022, the patients met the criteria of both ocular surface disease index (OSDI) ≥13 scores and standardized patient evaluation of eye dryness (SPEED)≥ 8 scores were enrolled in Kaohsiung Veteran General Hospital. Three separate treatment sessions of IPL therapy combined with MGX administered to the lower lids with an interval of 28 days. Further tear film assessment included lipid layer thickness (LLT), tear meniscus height (TMH), non-invasive tear break-up time (NIBUT), meibomian gland loss (MGL) either beforeor after 1st and 3rd IPL therapy combined with MGX. Besides, lissamine green staining and pain scores were also recorded. We totally enrolled 37 patients of 74 eyes. Men accounted for 18.92% (7/37). The mean age was 54.51 ± 11.72 years. The mean OSDI scores were 58.12 ± 22, while the SPEED scores were 17.03 ± 5.98. The mean Schirmer’s test was 3.66 ± 2.43 mm. After three sessions IPL treatment with MGX, the OSDI, SPEED, LLT, TMH, MGL, MGXS and pain scores were significantly improved. For the MGX scores (MGXS) ≤20 group, MGL and lissamine green scores showed significant improvements. For the MGXS >20 group, TMH and dry spot rate revealed statistically improvement. Noninvasive IPL therapy with MGX statistically improved not only dry eye symptoms but also tear film assessments.

The encapsulation of proteins into core-shell structures is a widely utilised strategy for controlling protein stability, delivery and release. Despite the recognised utility of these microstructures, however, core-shell fabrication routes are often too costly or poorly scalable to allow for industrial translation. Furthermore, many scalable routes rely upon emulsion-techniques implicating denaturing or environmentally harmful organic solvents. Herein, we investigate core-shell protein encapsulation through single-feed, aqueous spray drying: a cheap, industrially ubiquitous particle-formation technology in the absence of organic solvents. We show that an excipient’s preference for the surface of the spray dried particle is well-predicted by its hydrodynamic diameter (Dh) under relevant feed buffer conditions (pH and ionic strength) and that the predictive power of Dh is improved when measured at the spray dryer outlet temperature compared to room temperature (R2 = 0.64 vs. 0.59). Lastly, we leverage these findings to propose an adaptable design framework for fabricating core-shell protein encapsulates by single-feed aqueous spray drying.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

(1)Background: Early-age concrete shrinkage induces stress that impact the cost and service life of concrete pavements. (2)Methods: In this study, strain measurements of field slabs were conducted and a methodology was presented that independently derived autogenous, drying, and thermal shrinkages in the initial stages of concrete placement. Total strain was measured according to five different environmental conditions and shrinkage strain was calculated for each condition. (3)Results: By measuring the strain of the slab and the specimen, the drying shrinkage strain was measured to be approximately 54% better than that by the conventional non-stressed cylinder method because it was possible to measure the drying shrinkage strain at the surface rather than in the middle part of the slab along its depth direction. When the water-to-cement ratio increased (35→40%), there was a considerable reduction (317με→82με) of autogenous shrinkage strain for the concrete at 28 days of age. Furthermore, calculation of stress-dependent strain allowed the presentation of more intuitive and accurate results. (4)Conclusion: As the measurement of independent shrinkage occurrence is possible, the consequent calculated result of the stress-dependent strain acting on real slabs will facilitate improvement in the construction quality, reduction in the development of defects in the concrete structure, and increase in the service life.

Among the many neglected underutilized species, tuberous Andean root crops like the ahipas (Pachyrhizus ahipa) constitute a promising alternative for increasing diversity in nutrient sources and food security at a regional level. In this study, we present the content of some functional compounds in tuberous roots from several ahipa accessions and the progenies of the interspecific hybrid X207 (P. ahipa × P. tuberosus). A significant objective was to determine protein and free amino acids in the roots to evaluate their food quality as protein supply. The interspecific hybrids have been found to possess the root quality to provide the crop with a higher dry matter content. The high dry matter content of the P. tuberosus Chuin materials is retained in the root quality of the hybrids. Food functional components like carbohydrates, organic acids, and proteins were determined in several ahipa accessions and a stable (non-segregating) progeny of the interspecific hybrid, X207. The X207 roots showed a significantly higher dry matter content and a lower content in soluble sugars, but no significant differences were found in starch content or organic acids compared to the ahipa accessions. About the root mineral contents, Fe and Mn concentrations in X207 were significantly raised compared to the average of ahipa accessions. Among the ahipa and the hybrid, no prominent differences in protein content or protein amino acids were found, being both partially defective in providing sufficient daily intake of some essential amino acids. Root weight, a central component of root yield, was significantly higher in X207, but thorough field studies are required to substantiate the hybrid’s superior yield performance..

Understanding the role of invasive species in ecosystem functioning represents one of the main challenges in ecology. Pteridium aquilinum is a successful cosmopolitan invasive species with negative effects on the ecological mechanisms that allow secondary succession. In this study we evaluated whether P. aquilinum favours the establishment of alternative states, as well as the effect of recovery strategies on the secondary succession. A random stratified sampling was established with three treatments, each one with at least 50 year of fern invasion and with variations on the periodicity of fires and cuttings (chapeos) vs one control without fern bracken We determined the species richness and composition, as well as the relative importance value (IVI) in each treatment. We found that P. aquilinum decreases the action of the mechanisms that allow secondary succession, particularly facilitation. The recovery strategies consist in monthly cuttings and control fires allow to recover the secondary succession and eventually, the regeneration of areas invaded by P. aquilinum. Our study has relevant implications on the ecology of alternative state, and in practical strategies to maintain tropical forests, as well as for the maintenance of environmental services and sustainability.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

The dimensional effect of the accumulation of an electric charge with a density of up to 270 μF/g by the system of compacted zirconium dioxide nanoparticles during exposure in an electric field (5000 V/m) under normal physical conditions is determined. Based on a qualitative complex analysis of the forms of appearance of the effect, it is shown that the place of localization of different charge carriers is the surface of nanoparticles. The supposed mechanism of this effect is considered using the theory of dispersed systems, the band theory, and the theory of contact phenomena in semiconductors. It was concluded that this mechanism is due to the phenomenon of localization of electron-type charge nanoparticles in the near-surface zone of the material in contact with the adsorption ion atmosphere. This effect is relevant for modern nanoelectronics, microsystem technology, and printed electronics.

This paper presents an advanced microstructural analysis of the AlSiMg, Ti64 and N700 powders used for additive manufacturing. The internal microstructure of the regular and irregular powder grains were characterized down to atomic resolution by using scanning electron microscopy and high resolution scanning transmission electron microscopy.The accretionary forms on top of the irregular AlSiMg powder grains exhibit a slightly coarse microstructure with a network of eutectic Si consisting of nano-crystallites, suggestinga slower cooling than the grain itself that contain a predominately amorphous Si network. A nm thin amorphous C layer on the surface of some Ti64 plasma atomized powder grains promoted the attachment of satellites and growth of envelopes. In case of gas atomized N700 powder grains, we identified thin oxide and carbon amorphous layers as well as metal segregations at the interface between the grain body and the accretionary forms.

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

In this study one of the most innovative sintering techniques up to date was evaluated: Electro-Sinter-Forging (ESF). Despite it has been proved to be effective in densifying several different metallic materials and composites, bearing steels such as 100Cr6 have never been processed so far. Pre-alloyed Astaloy CrM powders have been ad-mixed with either graphite or graphene and then processed by ESF to produce a 100Cr6 equivalent composition. Porosity has been evaluated by optical microscopy and compared to that one of 100Cr6 commercial samples. Mechanical properties such as hardness and transverse rupture strength were tested on samples produced by employing different process parameters and then submitted to different treatments (machining, heat treatment). The experimental characterization highlighted that porosity is the factor mostly affecting mechanical resistance of the samples, correlating linearly to the transverse rupture strength. Hardness on the other side does not correlate to the mechanical resistance because process related cracking has a higher effect on the final properties. Promising results were obtained that give room to the sinterability by ESF of materials difficult to sinter by conventional press and sinter techniques.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

The aim of this study is to present the spatial and temporal variability of the frequency of dry and wet days and dry and wet spells against the background of changes in precipitation and atmospheric circulation. The study is based on daily precipitation totals from 46 meteorological stations in Poland for the years 1966-2023. Additionally seven circulation indices were used: GBI, NAO, AO, EA, EA/WR. SCAND ana AMO. Dry days are defined as days without precipitation. Wet days are days with at least 1 mm of precipitation. It was shown that dry spells are much more common that wet spells, are longer and cover larger areas. Long term changes in annual characteristics of dry and wet days and spells are statistically insignificant. Only the length of the longest dry spell in the year increases. However, there are significant changes in their annual cycles. Spring is drier, in summer months, precipitation decreases in the south and increases in the north, November and December, symbols of gloomy rainy weather, are increasingly drier, rainy weather moved to January and February. The impact of circulation varies with seasons and NAO, Ao, SCAN and GBI indices have the strongest impact.

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

With the application of high-precision, enormous rotating equipment and the addition of harsh working conditions, the advantages of dry gas sealing technology are increasingly obvious. Herein, research on the dynamic stability of dry gas seals is reviewed based on their operating mechanism. The influence of the dry gas seal structure, vibration response, and dynamic followability on the reliability of the shaft end sealing system of rotating machinery is the focus of current dry gas sealing technology. This work reviews the research history; analyzes the key coefficient of instability of the sealing system under external disturbances and the existing research on stability models; discusses the influence of starting and stopping characteristics, working conditions, and groove parameters on the stability of dry gas seals; and points out the shortcomings in the existing research. In addition, potential developments in dynamic stability are proposed, including improving model accuracy, improving experimental techniques, or applying intelligent control and optimization methods to enhance the dynamic stability of the sealing system. Finally, the development prospects for dry gas sealing technology in intelligent monitoring and wide temperature range adaptations are discussed, and theoretical guidance for improving the dry gas seal system is provided.

This study aimed to investigate the effect of adding Mirror Visual Feedback Therapy (MFT) after Dry Needling (DDN) on sensitivity and motor performance in patients diagnosed with Post-Needling pain from Myofascial Trigger Points (MTrPs) in lateral elbow pain patients. A randomized, controlled, two-arm pilot trial following Consolidated Standards of Reporting Trials (CONSORT) was conducted at the European University of Madrid between February 1, 2023, and June 2, 2023. A total of 49 patients (F=23, M=26) were randomly assigned to the Experimental Group Deep Dry Needling, Ischemic Compression, Cold Spray, Stretching, and Mirror Therapy (n=25), and the others receiving the same interventions without Mirror Therapy (n=24). Pre- and post-treatment assessments encompassed Post-needling pain (VAS), pressure pain threshold (PPT), two-point discrimination threshold (TPDT), and maximum hand grip strength (MHGS). Post-needling pain intensity in the EG showed statistically significant reductions (MD = 0.400, SEM = 0.271, W = 137.00, p = 0.047) following the addition of MT to the DDN protocol. Similarly, PPT exhibited significant improvements (MD = 0.148 Kg/cm2, SEM = 0.271, W = 262.00, p < 0.001). However, TPDT and MHGS did not show significant differences between initial and post-treatment measurements. The addition of MFT to DDN for MTrPS in lateral elbow pain reduced Post-needling pain and influenced on sensory perception in lateral elbow pain patients with Myofascial Trigger Points. Despite observed clinical effects not reaching statistical significance, these findings offer valuable insights for future research considerations.

Dry eye syndrome (DES) has become increasingly prevalent due to the prolonged use of digital devices in modern society. Individual supplementation with lutein or docosahexaenoic acid (DHA) demonstrated potential benefits for eye health. This study aimed to investigate the effects of lutein plus DHA complex supplementation on DES, visual function, and memory in healthy individuals. Thirty-four participants, aged 40~60 years, received lutein/DHA complex supplements (containing 10 mg free-form lutein, 200 mg DHA, 30 mg red algae extract (astaxanthin), phosphatidylserine, and vitamin A) for 12 weeks. Ophthalmological examinations and memory tests were carried out, and a questionnaire was administered at weeks 0, 6, and 12 of the study. After 12 weeks of the intervention, the tear break-up time had significantly increased, and intraocular pressure (IOP) had significantly decreased. This suggests that lutein/DHA complex supplementation may reduce the IOP and offer potential benefits for DES, as indicated by improved tear stability.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

This study analyzes the potential response of the seasonal cycle of heatwave (HWDI), dry (CDD) and wet (CWD) spells indices over West Africa for the near (2031-2060) and the far (2071-2100) future periods, under RCP4.5 and RCP8.5 scenarios using CORDEX simulations. Although some relative biases during the historical period (1976-2005), the CORDEX simulations and their ensemble mean outperform the seasonal variability of the above indices over three defined sub-regions of West Africa (i.e., Guinea gulf, west and east Sahel). They have shown significant correlation coefficients and less RMSE. They project an increase in heatwave days for both near and far future periods over whole west Africa region under both RCP scenarios. In addition, the Sahel regions will face to a decrease in wet spells days from March to November, whereas, the Gulf of Guinea will face to a decrease during all the year, except CCCLM simulation which indicates an increase during the retreat phase of the monsoon (October to December). The results also have shown an increase in dry spells over Sahel regions, more pronounced during March-November period, whereas, over Guinea gulf, the increase is observed over the entire year. On the other hand, the months of increasing dry spells and decreasing wet spells coincide, suggesting that countries in these regions could be exposed simultaneously to dry season associated with a high risk of drought and heatwave under future climate conditions.

Fusarium dry rot is one of the major postharvest potato diseases of during storage after harvest, which not only results in quality degradation but also brings up huge economic losses. The dis-ease can be elicited by some species of Fusarium, the pathogenic fungi of Fusarium causing potato dry rot are considerably diverse in various countries and regions. Fusarium spp. infection is as-sociated with dry rot produce mycotoxins, which has phytotoxicity and mycotoxicoses on hu-mans and animals. Chemical synthetic fungicide is considered as the main control measure to Fusarium dry rot of potato, nevertheless, it is unfortunate that the persistent application inevitably results in the emergency of resistant strain and environmental contamination. A comprehensive disease control strategy includes potato cultivar selection, appropriate cultural practices (crop rotation, cultivate pattern, fertilization, and irrigation), harvesting process and postharvest treatment (harvesting, classification, packaging, wound healing), storage condition (environ-mental disinfection, temperature, humidity and gas composition) along with the application of fungicide pre-harvest or postharvest. Recently, emerging studies indicated that eco-friendly strategies include physical control, chemical methods (such as the application of generally rec-ognized as safe (GRAS) compounds or chemical (elicitors) and biological control have been in-troduced to combat Fusarium dry rot of potato.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

This study was conducted to determine the effect of different types of olive cake (five treatments) in the diet of Bísaro pigs on the volatile compounds and sensory characteristics in the dry-cured loin and dry-cured “cachaço” (2 processed meat products). The treatments applied are based on the type of extraction and this may imply differences in their water and fat content. Eighty com-pounds were identified, and grouped into eight chemical classes: hydrocarbons, aldehydes, es-ters, alcohols, ketones, acids, furans, and other compounds. Aldehydes and alcohols were the ma-jor groups of compounds, representing 57.06-66.07 % and 68.67-75.61 % for the loin and “cacha-ço”, respectively. There were no significant differences between treatments for any of the volatile compounds identified. The major aldehydes were hexanal, heptanal, pentanal, and propanal. These compounds were significantly higher (p<0.001) in “cachaço”. This significant difference be-tween the two types of dry-cured products is directly related to the amount of total fat content. The major alcohols were 2.3-butanediol, 1-octen-3-ol, 1-butanol, 3-methyl, 1-hexanol, benzyl-alcohol and glycidol. Except for compounds 2,3-butanediol and benzyl-alcohol, the majority in this group are significantly different in terms of the type of dry-cured product. As for the sensory evaluation, for both dry-cured products, the trained tasters did not detect significant differences between the different treatments, which is in line with the results obtained for volatile compounds.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

In the cold deserts of the McMurdo Dry Valleys (MDV) the suitability of soil for microbial life is determined by both contemporary processes and legacy effects. Climatic changes and accompanying glacial activity have caused local extinctions and geochemical changes to soil ecosystems over several million years, while high elevation refugia may have escaped these disturbances and existed under relatively stable conditions. This study describes the impact of historical glacial and lacustrine disturbance events on microbial communities across the MDV. Soil bacterial communities from 17 sites representing either putative refugia or sites disturbed during the Last Glacial Maximum (LGM) (22-17kya) were characterized using 16S metabarcoding. Regardless of geographic distance, several putative refugia sites at elevations above 600 meter displayed highly similar microbial communities. At a regional scale, community composition was found to be influenced by elevation and geographic proximity more so than soil geochemical properties. These results suggest that despite the extreme conditions, diverse microbial communities exist in these putative refugia that have presumably remained undisturbed at least through the last glacial maximum. We suggest that similarities in microbial communities can be interpreted as evidence for historical climate legacies on an ecosystem-wide scale.

Often yam varieties grown in different agro-ecologies show differential responses across production environments, a term known as genotype-by-environment interaction. Genotype-by-environment interaction makes selecting the best genotypes under varied production environments more complex. This study tested twenty yam genotypes evaluated in six test environments to assess genotype, environment, and the interaction between genotypes and environmental effect for tuber yield, yam mosaic virus, and dry matter content. The experiments were conducted in two seasons across three locations in Uganda using a randomized complete block design with three replications. The results showed a significant effect (p ≤ 0.001) for genotype (G), environment (E), and genotype by environment interaction for all the traits. Serere 2021 and Namulonge 2021 were identified as the most discriminating and representative environments for testing the yam mosaic virus, respectively. Serere 2021 was recognized as the most discriminating environment, whereas Arua 2021 was identified as the closest to an ideal environment for assessing yam tuber yields. The tested genotypes also exhibited high resistance to yam mosaic virus disease, high tuber yields, and high dry matter content. Genotypes UGY16020, UGY16034, UGY16042, and UGY16080 demonstrated great resistance to yam mosaic virus disease, high yielding, and considerable dry matter content and are thus potential parents for yam improvement. Further evaluation of the four genotypes should be done under farmers' production systems for selection, improvement, and release as new yam varieties for Uganda

Each year in March, adherents of the Bahá’í faith abstain from eating and drinking from sunrise to sunset for 19 days. Thus, Bahá’í fasting (BF) can be considered as a form of daytime dry fasting. We tested if BF decreases energy expenditure after a meal and improves anthropometric measures, and systemic and tissue-level metabolic parameters. This was a self-controlled cohort study with 11 healthy men. We measured anthropometric parameters, metabolic markers in venous blood, and pre- and postprandial energy metabolism at systemic (indirect calorimetry) and tissue (adipose tissue and skeletal muscle microdialysis) level, both before and during BF. During BF, we found reduced body weight, body mass index, body fat and blood glucose. Postprandial increase in energy expenditure was lower, diet-induced thermogenesis tended to be lower. In adipose tissue, perfusion, glucose supply and lipolysis were increased. In skeletal muscle, tissue perfusion did not change. Glucose supply and lipolysis were decreased. Glucose oxidation was increased, indicating an improved insulin sensitivity. BF may be a promising approach to losing weight and improving metabolism and health. However, outside the context of religiously-motivated fasting, skipping a meal rather in the evening (dinner cancelling) might be recommended, as metabolism appears to be reduced in the evening.

Consumer demands for new sensory experiences have driven the research of unconventional yeasts in beer. While much research exists on the use of various common Saccharomyces cerevisiae strains as well as non-Saccharomyces yeasts, there exists a gap in knowledge regarding other non-cerevisiae Saccharomyces species in the fermentation of beer, outside that of S. pastorianus. Here, five distinct species of Saccharomyces from the UC Davis Phaff Yeast Culture Collection, as well as one interspecies hybrid from Fermentis, were chosen to ferment 40 L pilot scale beers. S. kudriavzevii, S. mikatae, S. paradoxus, S. bayanus, and S. uvarum yeasts were fermented in duplicate, with one fermenter in each pair receiving 10 g/L dry-hop during fermentation. Analytical measurements were made each day of fermentation and compared to controls of SafAle US-05 and SafLager W 34/70 for commercial brewing parameters of interest. Finished beers were also analyzed for aroma, taste, and mouthfeel to determine the flavor of each yeast as it pertains to brewing potential. All beers exhibited spicy characteristics, likely from the presence of phenols; dry-hopping increased fruit notes while also increasing perceived bitterness and astringency. All of the species in this study displayed great brewing potential, and might be an ideal addition to beer depending on a brewery’s desire to experiment with flavor and willingness to bring a new yeast into their production environment

Adding a submerged zone (SZ) is deemed to promote denitrification during dry periods and thus improve NO3--N removal efficiency of a bioretention system. However, few studies had investigated the variation of nitrogen concentration in the SZ during dry periods and evaluated the effect of the variation on nitrogen removal of the bioretention system. Based on the experiment in a mesocosm bioretetion system with SZ, this study investigated the variation of nitrogen concentration of the system under 17 consecutive cycles of wet and dry alternation with varied rainfall amount, influent nitrogen concentration and antecedent dry periods (ADP). The results indicated that (1) during the dry periods, NH4+-N concentrations in SZ showed an exponential decline trend, decreasing by 50% in 12.9 ± 7.3 hours; while NO3--N concentrations showed an inverse S-shape decline trend, decreasing by 50% in 18.8 ± 6.4 hours; (2) during the wet periods, NO3--N concentration in the effluent showed an S-shape upward trend; and at the early stage of the wet periods, the concentration was relatively low and significantly correlated with ADP, while the corresponding volume of the effluent was significantly correlated with the SZ depth; (3) in the whole experiment, the contribution of nitrogen decrease in SZ during dry periods to NH4+-N and NO3--N removal accounted for 12% and 92%, respectively; and the decrease of NO3--N in SZ during the dry period was correlated with the influent concentration in the wet period and the length of the dry period.

Purpose: To evaluate seasonal variation in intra-ocular pressure (IOP) with and without short tear break-up time (SBUT, BUT ≤ 5 s). Methods: This study enrolled 176 patients who visited one of six eye clinics in Japan for IOP measurement at every season. The mean patient age was 67.9 years, including 79 males. We compared the seasonal variation in IOP (mean ± SD) across spring (Mar-May), summer (Jun-Aug), fall (Sep-Nov), and winter (Dec-Feb). Results: The IOP (mmHg) in winter and summer, respectively, was 12.8 ± 3.7 and 12.8 ± 3.1 for non-glaucoma patients without SBUT (n = 47, P = 0.964), 14.8 ± 3.4 and 13.3 ± 3.4 for non-glaucoma patients with SBUT (n = 57, P < 0.001), 14.3 ± 3.2 and 14.1 ± 3.4 for glaucoma patients without SBUT (n = 36, P = 0.489), and 13.3 ± 3.0 and 11.6 ± 2.9 for glaucoma with SBUT (n = 36, P < 0.001). Seasonal variation was largest across the seasons in the glaucoma with SBUT group, and the magnitude of seasonal variation correlated with BUT (β = 0.228, P = 0.003). Conclusions: Seasonal variation tended to be larger in patients with SBUT than those without SBUT.

Open pit mining is a common activity in the Yucatan peninsula for the extraction of limestone. This mining is known under the generic name of quarries, and regionally as sascaberas (sascab=white soil in Mayan language). These areas are characterized by the total removal of the natural vegetation cover and soil in order to have access to the calcareous material. The present study shows the composition and structure of the vegetation in five quarries after approximately ten years of abandonment, and the conserved vegetation near to each one of the quarries in southeastern Quintana Roo. Using a canonical correspondence analysis (CCA), the distribution of the species was determined in relation to the edaphic variables: soil depth, percentage of organic matter (OM), cationic exchange capacity (CEC), pH and texture. 26 families, 46 genera and 50 species were recorded in the quarries and 25 families, 45 genera and 47 species were recorded in the conserved areas. The dominant species in the quarries belong to the families Poaceae, Fabaceae, Rubiaceae and Anacardiaceae. The quarries with higher values of OM (1.63%), CEC (24.05 Cmol/kg), depth (11 cm) and sand percentage (31.33%) include the following species like Lysiloma latisiliquum, Metopium brownei and Bursera simaruba which are commonly found in secondary forests. On the other hand, quarries with lower values of OM (0.39%), CEC (16.58 Cmol/kg) and depth (5.02), and higher percentage of silt (42.44%) were dominated by herbaceous species belonging to the Poaceae family and by Borreria verticillata, which are typical in disturbed areas of southeastern Mexico. In all cases, the pH was slightly alkaline due to the content of calcium carbonate (CaCO3), characteristic of the soils of the region. The edaphic variables are significantly correlated with the development and distribution of vegetation, and with the structure of the communities.

Bamboo agroforestry is currently being promoted as a viable land use option to reduce dependence on natural forest for wood fuels in Ghana. To align the design and introduction of bamboo agroforestry in conformity with farmers’ needs, perceptions, skills and local cultural practices, information on its acceptability and adoption potential among farmers is necessary. It is therefore the objective of this study to (1) describe bamboo ethnobotany and (2) assess socioeconomic factors that affect the acceptability and adoption of bamboo and its integration into farming practices. Accordingly, information has been collected from 200 farmers in the dry semi-deciduous forest zone of Ghana. The study identified the socioeconomic risks and uncertainties as well as biophysical factors that are likely to influence the potential adoption of bamboo agroforestry in the study region. Gender, age, farmers’ known uses of bamboo, the practice of leaving trees on farmlands, farmers’ networking and access to extension services, land availability and ownership by farmers were identified as suitable predictor variables for the adoption of bamboo agroforestry. It is envisaged that bamboo agroforestry is a good bet in the DSFZ though there is the need to explore domestic energy (fuelwood) provision and substitution potential in order to have a broader picture of the technology.

The experiment was conducted at livestock research and development station surezai Peshawar during March 2012 to study the effect of cotton seed cake, Lucerne hay supplementation on intake of maize stover and weight gain by male sahiwal bull. Twelve (12) young Sahiwal bull breed, 280 kg average liveweight and 2 years of age were randomly put into 4 groups of 3 animals under intensive feeding system to determine the effect of different protein supplements on growth, and intake of chopped, dried maize stover. A control group was fed stover adlibitum only, and the other groups were fed daily 750 g cottonseed cake/head, 1 kg lucerne hay or 900 g of lucerne/cottonseed cake (66:34; w/w). Significant differences were observed on average daily live weight gains. Animals on lucerne and its mixture registered higher daily gains (243 g) and (330 g) respectively, followed by cottonseed cake (156 g); the control group lost weight (-8.0 g/d). Contrary to the live weight gains, animals fed on lucerne and its mixture had lower maize stover intakes, 3.35 kg DM/animal/day and 3.70 kg DM respectively, while those on cottonseed cake and the control group ingested respectively 4.72 kg DM and 4.16 kg DM maize Stover. It is concluded that during the critical period in the suburb of Peshawar, small-scale farmers can prevent loss in live weight by utilizing simple available rations.

Agro-meteorology is the relationship between agriculture and weather. All farm activities are affected by weather. Therefore it is always necessary to monitor the weather as a forecast. The aim of the research was to monitor the weather and rainwater samples obtained at Federal College of Agriculture, Akure, Ondo State, Nigeria. For the eight months periods, results were obtained. The mean results for the physicochemical parameters were: TDS (12.25 mg/L), temp (28.13 ^oC), pH (6.63), EC (24.25µS/cm), Free CO₂ (24.38mg/L), nitrate (0.16mg/L), phosphate (0.17mg/L), sulphate (0.18mg/L). The rainwater was colorless and had no odor. The mean meteorological data: The prevailing wind directions were from SE, mostly in May, June, July and November and NE. The dry and wet temperatures were 22-29 ^oC and 20-26 ^oC respectively. The maximum value was observed in the month of July. The correlation matrix showed that there were many strong correlations in the physicochemical properties. The months of May, June and July had the highest wind speed. In these months there would be a need to use a windbreaker around the crops planted to avoid soil erosion and damaging of plants.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

To investigate the impacts of various sources of omega-3 on feed intake, digestibility, and blood metabolites in horses, this research was conducted. In this survey, 6 medium-sized Turkmen horses, aged 14 to 16 years, were used. The horses had no movement and health problems. This research was carried out in the form of a rotating design and included 3 periods, and each treatment had 2 repetitions in each period. In each experimental period, horses were randomly assigned to each of the 3 experimental treatments. The experimental treatments included C) Omega-3-free supplement (control treatment), R) Persialin flaxseed oil, and P) Persialin fat powder. At the beginning of each period, after the withdrawal period for the previous period, blood and feces samples were taken as the covariate factors, then the experimental treatments were consumed for 14 days, and after the adaptation to 100 grams of supplementing fat powder or flax seed oil, blood, and feces samples were taken at the end of the course. Fat supplements were added to the concentrate 1.5 hours before feeding the midday hay. The palatability was affected by the P treatment and was significantly lower than the R and C groups (P<0.05). But the difference between the two treatments (R and C) was insignificant in any of the periods. The digestibility of acid detergent insoluble fiber (ADF), crude protein (CP), ether extract (EE), and organic matter were not affected by any of the experimental treatments. Blood metabolites including glucose, cholesterol, triglyceride, total protein, and blood urea nitrogen were not influenced by experimental treatments. The serum albumin concentration of horses was affected by the R treatment in the first and third periods, but no significant difference was observed between the treatments in the second period.

Introduction: Dental health problems including dental plaque are common health problems affecting people of different age groups globally. Air-polishing is a safe tooth polishing technique used by dental professionals for stain and plaque removal and as preventive procedure for dental health. Here we report the technical improvisation of existing air-polishing technique by supplementing cannabinoid powder into the classic polishing powder for effective removal of supragingival and subgingival plaque and inhibition of plaque forming bacteria. Methods: The cannabidiol (CBD) powder was added to the tooth polishing powder (AIR-N-GO, classic) at 1% (wt/wt) ratio. The study was conducted on 12 patients, of which 6 received regular polishing treatment and 6 received CBD-supplemented polishing treatment. The dental plaque samples were collected before and after each treatment and subjected to in vitro microbiological analysis and the colony forming units (CFU) were analyzed using automated colony counter. Results: Based on in vitro microbiological analysis, the average CFU of interdental space samples collected from post-CBD-supplemented polishing treatment was significantly reduced (linear fold change between 3.9-18.4) compared to that of post-regular polishing (linear fold change between 1.0-2.6) treatment. Conclusions: CBD-supplemented polishing powder can help in effective removal and killing of dental plaque bacteria during the polishing treatment. CBD powder can be added as enhancing supplement to the existing polishing powders.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

Predictive factors associated with a decline in swallowing function after 2 years were examined in 3,409 Japanese older people aged ≥ 75 years who had undergone a dental checkup in Gifu Prefecture, Japan. Participants with normal swallowing function in a baseline survey in April 2018 were followed for 2 years. Swallowing function was assessed by a repetitive saliva swallowing test. After 2 years, 429 participants (13%) who could not swallow at least three times in 30 seconds were diagnosed as having a decline in swallowing function. Multivariate logistic regression analyses showed the decline in swallowing function after 2 years was associated with male gender (odds ratio [ORs]: 0.772; 95% confidence interval [CIs]: 0.615–0.969), age ≥ 81 years (presence; ORs: 1.523; 95% CIs: 1.224–1.895), support/care-need certification (presence; ORs: 1.815; 95% CIs: 1.361–2.394), periodontal pocket depth (PPD) ≥ 4 mm (presence; ORs: 1.469; 95% CIs: 1.163–1.856), difficulty in biting hard food (yes; ORs: 1.439; 95% CIs: 1.145–1.808), choking on tea and water (yes; ORs: 2.543; 95% CIs: 2.025–3.193), and dry mouth (yes; ORs: 1.316; 95% CIs: 1.052–1.646) at baseline. Therefore, the dental checkup items associated with a decline in swallowing function after 2 years were a PPD ≥ 4 mm, difficulty in biting hard food, choking on tea and water, and dry mouth. PPD status and confirming to the self-administered questionnaire about biting, choking, and dry mouth may be useful in predicting future decline in swallowing function.

The study was conducted to evaluate the agronomic performance, forage yield, and nutritive values of Desho grass varieties under supplementary irrigation at Dambi Dollo University experimental site, Western Ethiopia. Three Desho grass varieties (Areka /DZF#590, Kindu kosha-1/DZF #591, and Kulumsa /DZF #592) were arranged in randomized complete block design (RCBD) with three replications. The CROPWAT 8.0 model, local climate data, forage data, and soil data were used to determine Desho grass water requirements and irrigation schedules. The agronomic parameters, yield, chemical composition, and in vitro digestibility of the feed samples at standardization cut were determined following the standard procedures. The results showed significant differences (p

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.