Local thermal comfort (TC) and draught rate (DR) has been studied widely. There has been more meaningful research performed in controlled boundary condition situations than in actual work environments involving occupants. TC conditions in office buildings in Estonia have been barely investigated in the past. In this paper, the results of TC and DR assessment in five office buildings in Tallinn are presented and discussed. Studied office landscapes vary in heating, ventilation and cooling (HVAC) system parameters, room units and elements. All sample buildings were less than six years old, equipped with dedicated outdoor air ventilation system and room conditioning units. The on-site measurements consisted of TC and DR assessment with indoor climate questionnaire (ICQ). The purpose of the survey is to assess the correspondence between HVAC design and the actual situation. Results show, whether and in what extent the standard-based criteria for TC is suitable for actual usage of the occupants. Preferring one room conditioning unit type or system may not guarantee better thermal environment without draught. Although some HVAC systems observed in this study should create the prerequisites for ensuring more comfort, results show that this is not the case for all buildings in this study.

The polymer binder, poly(imide-co-siloxane) (PIS), was synthesized and applied to form a thin cathode layer composites for a thermal battery that has an unusually high operating temperature of 450 °C. The PIS was prepared through cross-linking of the polyimide with polysiloxane. The morphology of FeS₂/PIS composites showed that FeS₂ particles was coated with the PIS cross-linked gel. The FeS₂/PIS composites enabled to fabricate mechanically stable thin cathode layer that was 20–10% of the thickness of a conventional pellet-type cathode. The FeS₂/PIS composites were stable up to 400 °C and maintained their morphology at this temperature. PIS coating layers decomposed at 450 °C and a new residue was generated, which was observed by transmission electron microscopy and the compositional change was analyzed. The FeS₂/PIS composites showed enhanced thermal stability over that of FeS₂ in thermogravimetric analysis. The thermal battery with the PIS polymer binder showed a 20% discharge capacity increase when compared to a conventional pellet-type cathode.

Natural spa springs are diffused all over the world and their use in pools is known since ancient times. This review underlines the cultural and social spa context focusing on hygiene issues, public health guidelines and emerging concerns regarding water management in wellness or recreational settings. The question of the "untouchability" of therapeutic natural waters and their incompatibility with traditional disinfection processes is addressed considering the demand for effective treatments that would respect the natural properties. Available strategies and innovative treatments are reviewed, highlighting potentials and limits for a sustainable management. Alternative approaches comprise nanotechnologies, photocatalysis systems, advanced filtration. State of the art and promising perspectives are reported considering the chemical-physical component and the biological natural complexity of the spa water microbiota.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

As the interface between human and machine becomes blurred, hydrogel incorporated electronics and devices have emerged to be a new class of flexible/stretchable electronic and ionic devices due to their extraordinary properties, such as soft, mechanically robust and biocompatible. However, heat dissipation in these devices could be a critical issue and remains unexplored. Here, we report the experimental measurements and equilibrium molecular dynamics simulations of thermal conduction in polyacrylamide (PAAm) hydrogels. The thermal conductivity of PAAm hydrogels can be modulated by both the crosslinking density and water content in hydrogels. The crosslinking density dependent thermal conductivity in hydrogels varies from 0.33 to 0.51 Wm^-1K^-1, giving a 54% enhancement. We attribute the crosslinking effect to the competition between the increased conduction pathways and the enhanced phonon scattering effect. Moreover，water content can act as filler in polymers which lead to nearly 40% enhancement in thermal conductivity in PAAm hydrogels with water content vary from 23 to 88 wt%. Furthermore，we find the thermal conductivity of PAAm hydrogel is insensitive to temperature in the range of 25 ^oC – 40 ^oC. Our study offers fundamental understanding of thermal transport in soft materials and provides design guidance for hydrogel-based devices.

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

This study investigates the land surface temperature (LST) distribution from thermal infrared data for analyzing the characteristics of surface coverage using the Vegetation-Impervious-Soil (VIS) approach. A set of ten images, obtained from Landsat-5 Thematic Mapper, between 2001 and 2010, were used to study the urban environmental conditions of 47 neighborhoods of Porto Alegre city, Brazil. Porto Alegre has had the smallest population growth rate of all 27 state capitals in the last two decades in Brazil, with an increase of 11.55% in inhabitants from 1,263 million in 1991 to 1,409 million in 2010. We applied the environmental Kuznets curve (EKC) theory in order to test the influence of the economically-related scenario on the spatial nature of social-environmental arrangement of the city at neighborhood scale. Our results suggest that the economically-related scenario exerts a non-negligible influence on the physically driven characteristics of the urban environmental conditions as predicted by EKC theory. The linear inverse correlation R2 between household income (HI) and LST is 0.36 and has shown to be comparable to all other studied variables. Future research may investigate the relation between other economically-related indicators to specific land surface characteristics.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

The purpose of this study was to explore and develop high-resolution infrared thermal (HRIT) imaging for screening toddler’s fracture. A Toddler’s fracture is a common tibial fracture of children younger than 6 years old. Initial x-ray radiographs may not show the fracture and another x-ray during a follow-on visit is usually required. The study included 39 participants admitted to an emergency department with a suspected toddler’s fracture. X-ray confirmed 8 cases with a toddler’s fracture (20.5%). Infrared images of participants were recorded on their index visit, focusing on region-of-interests on the injured and the contralateral (uninjured) legs. The uninjured leg acted as a thermal reference. Nine statistical measures were extracted from the images: maximum, mini-mum, mean, standard deviation, median, mode, interquartile range, skewness, and kurtosis. Wilcoxon rank sum test indicated that maximum, mean, standard deviation, median, and inter quartile range temperature measures were significantly different (p<0.05) when comparing fractured and non-fractured legs. Principal component analysis of these measures highlighted distinct separation of toddler’s fracture and non-fracture cases. Similarly, plots of the statistical measures further confirmed clustering of toddler’s fracture cases. The study demonstrated that HRIT imaging can be a valuable tool for screening for toddler’s fracture.

This study investigated the risk of lung and bladder cancers in people residing in proximity of a coal-oil-fired thermal power plant in an area of north-eastern Italy, covered by a population-based cancer registry. Incidence rate ratios (IRR) by sex, age, and histology were computed according to tertiles of residential exposure to benzene, nitrogen dioxide (NO2), particular matter, and sulfur dioxide (SO2) among 1076 incident cases of lung and 650 cases of bladder cancers. In men of all ages and in women under 75 years of age, no significant associations were observed. Conversely, in women aged >75 years significantly increased risks of lung and bladder cancers were related to high exposure to benzene (IRR for highest vs. lowest tertile: 2.00 for lung cancer and 1.94 for bladder cancer) and NO2 (IRR: 1.72 for lung cancer; and 1.94 for bladder cancer). In these women, a 1.71-fold higher risk of lung cancer was also related to a high exposure to SO2. The findings of this descriptive study indicated that air pollution may have a role with regard to the risk of lung and bladder cancers, limited to women aged ≥ 75 years. Such increased risk warrants further analytical investigations.

Lightweight concrete is a promising alternative in modern construction due to its reduced weight and potential to improve thermal and structural efficiency. Incorporating sustainable materials, such as nopal mucilage and aloe vera, can optimize its properties, promoting more eco-friendly practices in the industry. This study evaluates six concrete mixtures using different dosages of tuff, expanded clay, nopal mucilage, and aloe vera. Physical and mechanical tests were conducted, and the results revealed varied behaviors: mixtures with aloe vera showed extremes in water absorption and consistency, with tuff being very fluid and expanded clay having good workability. Mixtures with nopal mucilage were drier and less workable. In contrast, mixtures with expanded clay showed higher bulk density and variations in consistency and water absorption. Compressive strength varied depending on the lightweight agents used: mixtures with nopal mucilage-expanded clay and aloe vera-expanded clay showed moderate strengths, suggesting that these combinations can improve the strength of lightweight concrete. The different lightweight agents also affected the thermal and physical properties and the fractal dimension of the mixtures, indicating a greater structural complexity and better heat retention in combinations of expanded clay with nopal mucilage or aloe vera.

Loop-Mediated Isothermal Amplification (LAMP) is a widely used technique for nucleic acid amplification due to its high specificity, sensitivity, and rapid results. Advances in microfluidic lab-on-chip (LOC) technology have enabled the integration of LAMP into miniaturized devices, known as μ-LAMP, which require precise thermal control for optimal DNA amplification. This paper introduces a novel thermal bed design using PCB copper traces and FR−4 dielectric materials, providing a reliable, modular, and repairable heating platform. We present the design, fabrication, and control mechanisms of the thermal bed, demonstrating its ability to maintain accurate temperatures essential for μ-LAMP applications. The thermal bed’s performance is validated through finite element method (FEM) simulations, confirming its effectiveness in diverse applications such as disease diagnostics, biological safety, and forensic analysis.

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using High Temperature Confocal Laser Scanning Microscopy (HTCLSM). The in-situ observation of the heating and holding processes reveals critical insights into phase transformations, grain growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700°C, with significant grain boundary nucleation. At 900°C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000°C was confirmed. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr7C3), which significantly contribute to the material's strength. The comprehensive analysis using Transmission Electron Microscopy (TEM) confirmed the presence and distribution of Cr7C3 within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat treatment processes to enhance mechanical properties for maritime applications.

Background: Our previous study revealed that the addition of pentavalent cations, such as niobium (Nb), to zirconia stabilized with trivalent cations, such as yttrium (Y), increased fracture toughness. However, the coefficient of thermal expansion (CTE) and opacity also increased undesirably. Thus, a novel surface treatment is required to enhance fracture toughness without changing the CTE and the translucency. Methods: The surfaces of pre-sintered 3-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) and 4.2-mol% yttria-stabilized partially stabilized zirconia (4.2Y-PSZ) were treated with an Nb sol solution containing Nb2O5 nanoparticles. After drying and final sintering, a surface layer with high Nb content formed to a depth of approximately 1 mm. Results: Nb was equivalent to that of the bulk uniformly containing 1 mol% Nb2O5. The tetragonality of tetragonal zirconia near the surface increased with the addition of Nb, leading to improve fracture toughness in the surface layer and enhancing the fracture toughness of the entire specimen. However, the CTE and the translucency remained unchanged. Conclusions: The addition of pentavalent cations such as Nb, confined to the surface vicinity, improved fracture toughness without affecting the CTE and the translucency. By selectively adding Nb to the surface of weak parts of zirconia prosthesis, the overall strength can be improved, making it possible to produce highly reliable dental restorations.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Transfer RNA (tRNA) modifications are essential for the temperature adaptation of thermophilic and psychrophilic organisms, as they control the rigidity and flexibility of transcripts. To further understand how specific tRNA modifications are adjusted to maintain functionality in response to temperature fluctuations, we investigated whether tRNA modifications represent an adaptation of bacteria to different growth temperatures (minimal, optimal, and maximal), focusing on closely related psychrophilic (P. halocryophilus and E. sibiricum), mesophilic (B. subtilis), and thermophilic (G. stearothermophilus) Bacillales. Utilizing an RNA sequencing approach combined with chemical pre-treatment of tRNA samples, we systematically profiled dihydrouridine (D), 4-thiouridine (s4U), 7-methyl-guanosine (m7G), and pseudouridine (Ψ) modifications at single-nucleotide resolution. Despite their close relation, each bacterium exhibited a unique tRNA modification profile. Our findings revealed increased tRNA modifications in the thermophilic bacteria at higher temperatures, particularly showing elevated levels of s4U8 and Ψ55 modifications compared to non-thermophilic bacteria, indicating a temperature-dependent regulation that may contribute to thermotolerance. Furthermore, we observed higher levels of D modifications in psychrophilic and mesophilic bacteria indicating an adaptive strategy for cold environments by enhancing local flexibility in tRNAs. Our method demonstrated high effectiveness in identifying tRNA modifications compared to an established tool, highlighting its potential for precise tRNA profiling studies.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

The examination of ampacity in overhead transmission lines offers a comprehensive overview, covering its definition, thermal evaluation methodologies, standards, practical applications, and the potential of high-temperature low-sag (HTLS) conductors. By navigating through static and dynamic approaches to thermal evaluation and detailing methodologies prescribed by international standards like those from CIGRE and IEEE, this study provides a solid understanding of how ampacity is determined and optimized. Furthermore, the exploration of HTLS conductors introduces a forward-looking perspective on enhancing transmission capacity whereas mitigating the need for extensive infrastructure modifications. Through an analysis of regional considerations and preferences using Slovak standards and CIGRE Technical Brochure 601, insights are provided on how environmental factors influence transmission line performance. The analysis of the transition from traditional ACSR to advanced ACCC (Aluminium Conductor Composite Core) conductors demonstrates the tangible benefits of adopting advanced conductor technologies in real-world scenarios.

The development of offshore wind farms requires robust bonding solutions that can withstand harsh marine conditions for the easy integration of secondary structures. This paper investigates the durability performance of two adhesives: Sikadur 30 adhesive and Loctite UK 1351 B25 for use in offshore wind environments. Tensile tests on adhesive samples and accelerated aging tests were carried out under a variety of temperature and environmental conditions, including both dry and wet conditions. The long-term effects of aging on adhesive integrity are investigated by simulating the operational life of offshore installations. The evolution of mechanical properties, studied under accelerated aging conditions, provides an important indication of the longevity of structures under normal conditions. The results show significant differences in performance be-tween the two adhesives, highlighting their suitability for specific operating parameters. It should also be noted that for both adhesives, their exposure to different environments (seawater, distilled water, humid climate) over a prolonged period has shown that i) Loctite adhesive has a slightly faster initial uptake than Sikadur adhesive, but the later reaches an asymptotic plateau with a lower maximum absorption rate than Loctite adhesive; and ii) a progressive deterioration in the tensile properties following an exponential function. Therefore, aging behavior results showed a clear correlation with Arrhenius' law, providing a predictive tool for the aging process. Thus, the aging process of the two adhesives follows Arrhenius kinetics.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Rigid pavements at military airfields experience surface deterioration within 6-18 months of construction. The cause of this degradation is mainly due to combined exposure to repeated heat shocks from jet engine exhaust and spilled aviation oils (hydrocarbons). Surface degradation occurs in the form of disintegration of aggregates and cement paste into small pieces that pose severe risks of physical injury to maintenance crews or damage to an aircraft engine. Since coarse aggregates typically occupy 60-80% of the concrete volume, aggregates' thermal properties and microstructure should play a crucial role in the degrading mechanism. At high temperatures, concrete with lightweight aggregates is reported to have better performance compared to concrete with normal-weight aggregate. Thus, the present study carried out a detailed investigation of the mechanical and thermal performance of lightweight aggregate concrete exposed to the combined effects of high temperature and hydrocarbon oils simultaneously. To identify the resistance of different concrete with various lightweight coarse aggregates, pumice, perlite, lytag (sintered fly ash), and crushed brick were used as lightweight coarse aggregates in concrete. Also, basalt aggregate concrete was used as a reference. After cyclic exposures, all specimens were tested for residual mechanical, thermal, chemical, and microstructural properties. Overall, concrete with crushed brick aggregate and LYTAG used in this study showed superior resistance to the simulated airfield conditions.

This research investigates the compatibility of conventional air conditioning with the principles of green building, highlighting the need for systems that enhance indoor comfort while aligning with environmental sustainability. Conventional cooling systems, though proficient in regulating indoor temperatures, encounter several issues when incorporated into green buildings. These include energy waste, high running costs, and a misalignment with eco-friendly practices, which may also lead to detrimental environmental effects and potentially reduce occupant comfort, particularly in retrofit situations. Given the emphasis on sustainability and energy conservation in green buildings, there is a pressing demand for heating, ventilation, and air conditioning (HVAC) solutions that support these goals. This study emphasizes the critical need to reconsider traditional HVAC strategies in the face of green building advances. It advocates for the adoption of innovative HVAC technologies designed for eco-efficiency and enhanced comfort. These technologies should integrate seamlessly with sustainable construction, use greener refrigerants, and uphold environmental integrity, driving progress towards a sustainable and occupant-friendly built environment.

The aim of the experiment was to determine the effect of strontium oxide addition on zirconium silicate recrystallization when adding strontium oxide to the glaze composition. Zirconia glazes (4 different contents) were prepared to which strontium oxide was added in amounts of 0, 1, 3, 6, and 12 mass%. SrO. The characteristic temperatures of the raw glazes were measured, based on which the maximum firing temperatures were determined. The fired glazes were subjected to study of the phase composition and observation of the microstructure. Analysis of the characteristic temperatures showed a fluxing effect, but it was not as strong for all glazes. Differences in the amount of the crystalline phase of zirconium silicate obtained in fired glazes and the partial transition of zirconium silicate to the amorphous phase were observed. Observations of the microstructure clearly indicated an increase in the homogeneity of the distribution of zirconium silicate.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

In this study, we have focused on studying the heterogenous degradation kinetics of regarding the decomposition of emergency contraceptive agent levonorgestrel (LNG), which is a second-generation synthetic progestogen that is the active component of the racemic mixture of norgestrel. The degradation processes of the active pharmaceutical ingredient (API) were compared with the ones obtained from model system containing the API along with the excipients that are found in a commercialized pharmaceutical formulation in a mass ratio of 1:1 (LNGMIX), in order to observe if the excipients have a stabilizing or destabilizing effect for the degradation of this progestogen. To achieve this, the following investigational methods were used: FTIR (Fourier transform infrared) spectroscopy and thermal analysis (TG/DTG/DSC analysis). For the kinetic analysis the data obtained from two main decomposition processes observed on the DTG curves were used and processed with a preliminary method, namely ASTM E698 and two isoconversional methods: Friedman and Flynn-Wall-Ozawa. The isoconversional study revealed that the decomposition mechanism of both LNG and LNGMIX are complex, and the excipients have a stabilizing effect over decomposition of API in tablet.

Zero-dimensional (0D) tin halide perovskites feature extraordinary properties, such as broadband emission, high photoluminescence quantum yield, and self-absorption-free characteristics. The innovation of synthesis approaches for high-quality 0D tin halide perovskites has facilitated the flourishing development of perovskite-based optoelectronic devices in recent years. However, discovering an effective strategy to further enhance their emission efficiency remains a considerable challenge. Herein, we report a unique strategy employing rapid heat treatment to attain efficient self-trapped exciton (STE) emission in Cs4SnBr6 zero-dimensional perovskite. Compared to the pristine Cs4SnBr6, rapid thermal treatment (RTT) at 200°C for a duration of 120 seconds results in an augmented STE emission with photoluminescence (PL) quantum yield rising from an initial 50.1% to a substantial 64.7%. Temperature-dependent PL spectra analysis, Raman spectra, and PL decay traces reveal that the PL improvement is attributed to the appropriate electron-phonon coupling as well as the increased binding energies of STEs induced by the RTT. Our findings open up a new avenue for efficient luminescent 0D tin-halide perovskites toward the development of efficient optoelectronic devices based on 0D perovskites.

Converting chemical energy from green hydrogen to electricity using Membrane Exchange Protons Fuel cell (PEMFC) is a promising solution in various applications such e-mobility and building facilities. The electrical efficiency of PEMFCs can reach 60%. However, they are immensely sensitive to the working temperature, requiring good thermal management. Active thermal management systems are expensive and energy-consuming. Passive thermal management systems enable PEMFC thermal management without additional energy consumption. Here various passive thermal management technologies are reviewed. Different techniques are thorougly described and critically compared in terms of complexity, efficiency, cooling rate, scope of applicability, and the sizes of PEMFCs to which they apply. The conclusions provide a solid background for further investigations, and recommendations for future work are suggested.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

Trace metals are essential elements that play key roles in a number of biochemical processes governing human visual physiology in health and disease. Several trace metals, such as zinc, have been shown to play important roles in the visual phototransduction process. In spite of this, there has been little research conducted on the direct effect of trace metal elements on the visual pho-toreceptor rhodopsin. In the current study, we have determined the effect of several metal ions, such as iron, copper, chromium, manganese, and nickel on the conformational stability of rho-dopsin. To this aim, we analyzed, by means of UV-visible and fluorescence spectroscopic methods, the effects of these trace elements on the thermal stability of dark rhodopsin, the stability of its active Metarhodopsin II conformation, and its chromophore regeneration. Our results show that copper prevented rhodopsin regeneration and slowed down the retinal release process after il-lumination. In turn, Fe3+, but not Fe2+, increased the thermal stability of the dark inactive con-formation of rhodopsin, whereas copper ions markedly decreased it. These findings stress the important role of trace metals in retinal physiology at the photoreceptor level, and may be useful for the development of novel therapeutic strategies to treat retinal disease.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

Fe rich soft magnetic alloys are candidates for applications as magnetic sensors and actuators. These alloys can also be added to hard magnetic compounds to obtain spring magnets. In this work we produce two nanocrystalline Fe-Zr-B-Cu alloys by the powder metallurgy powder technology of mechanical alloying. The increase of the boron content favors the reduction of the crystalline size. Thermal analysis (by differential scanning calorimetry) shows at temperatures between 450 and 650 K wide exothermic processes, associated with the relaxation of tensions of the alloys produced by milling. At high temperatures, a main crystallization peak is found. The apparent activation of this process was determined by Kissinger and isoconversional methods. The values are compared with those found in the scientific literature. Likewise, adapted thermogravimetry permits to determine the Curie temperature. The functional response has been analyzed by hysteresis loop cycles. According to the composition, the decrease of the Fe/B ratio diminishes the magnetic soft behavior.

Cohesion in the refractory metals Cr, Mo, and W is phenomenologically described in this work via a n-body energy functional with a set of physically motivated parameters that were optimized to reproduce selected experimental properties characteristic of perfect and defective crystals. The functional contains four terms accounting for the hard-core repulsion, the Thomas-Fermi kinetic energy repulsion and for contributions to the binding energy of s and d valence electrons. Lattice dynamics, molecular statics, and molecular dynamics calculations show that this model describes satisfactorily thermodynamic properties of the studied metals whereas, unlike other empirical approaches from the literature, predictions of phonon dispersion relations and of surface and point defect energetics reveal in fair good agreement with experiments. These results suggest that the present model is well adapted to large-scale simulations and whenever total energy calculations of thermodynamic properties are unfeasible

The goal of this short communication is to analyze a published discussion that states that long-term residing at a thermoneutral indoor temperature condition hinders human thermal acclimation capacities. According to current research, human thermal acclimation and acclimatization capacities can be easily gained through repeated heat and cold exposures mixed with physical activity over a period of days (often 3–21 days). Furthermore, heat and cold adaptations are not permanent, and heat acclimation would progressively fade away if frequent heat exposures (associated with physical work/exercise) were discontinued. People who have been heat acclimatized for a long period and live in tropical places may progressively lose their physiological and perceptual benefits when they shift to temperate zones. On the other hand, the decay of cold acclimation and cold acclimatization has not been well examined, demanding future research on this area. To summarize, there is no evidence to support the claim that extended exposure to thermoneutral conditions impairs human acclimatization abilities.

The large-scale processing of Cassava (Manihot esculenta Crantz.) generates significant quantities of solid wastes annually. Cassava peels (CP) account for 5 wt.% - 30 wt.% of wastes from the processing of cassava tubers. The poor disposal and management of CP pose risks to human health, safety and the environment. Therefore, there is an urgent need to identify and examine low cost, socially acceptable and environmentally friendly strategies to mitigate the immediate and long terms disposal and management challenges. Lack of such measures results in the accumulation of CP wastes, which are currently buried, combusted, or dumped in open fields. Therefore, this paper reviewed the potential routes for the biochemical, thermochemical, and plasma valorisation of CP. The literature reviewed revealed that biochemical technologies such as anaerobic digestion (AD) and fermentation are the most widely utilised approaches currently adopted for CP valorisation. AD produces biogas (methane 50-72 vol. % and carbon dioxide 25-45 vol. %), whereas fermentation yields bioethanol. However, the numerous challenges such as substrate-induced inhibition, associated with the biochemical processes hamper microbial degradation, methane formation, and process efficiency. Furthermore, the processes generate secondary wastes or digestate/sludge, which requires additional processing before disposal. Therefore, innovative thermal, thermochemical, and plasma technologies were proposed to valorise CP into syngas, biofuels, bioenergy, biochemicals, and fertilizers, among others. However, the waste products of fermentation cannot be effectively utilised as bio-fertilizers, whereas bioethanol causes corrosion in engines. Overall, the biochemical, thermal, thermochemical and plasma technologies can effectively valorise CP for effective net energy generation.

This work explored and contrasted the effect of microstructure on the tensile properties of AlSi10Mg alloys generated by transient directional solidification depending on variations in cooling rate and Magnesium (Mg) content (i.e., 0.45 and 1wt.% Mg), with a focus on understanding the dendritic growth and phases constitution. Optical and Scanning electron (SEM) microscopies, CALPHAD and thermal analysis were used to describe the microstructure, forming phases and resulting tensile properties. The findings showed that the experimental evolution of the primary dendritic spacing is very similar when both directionally solidified (DS) Al-10wt.% Si-0.45wt.% Mg and Al-10wt.% Si-1wt.% Mg alloys samples are compared. The secondary dendritic spacing was lower for the alloy with more Mg, especially considering the range of high growth velocities. Moreover, a greater fraction of (Al+Si+Mg2Si) ternary eutectic islands surrounding the -Al dendritic matrix was noted for the alloy with 1wt.% Mg. As a result of primary dendritic spacings greater than 180 m related to lower cooling rates, slightly higher tensile properties were attained for the Al-10wt.% Si-0.45wt.% Mg alloy. In contrast, combining dendritic refining (< 150 m) and larger Mg2Si fraction, fast solidified DS Al-10wt.% Si-1wt.% Mg samples exhibited higher tensile strength and elongation. The control of cooling rate and fineness of the dendritic array provided a new insight related to the addition of Mg in slightly higher levels than conventional ones, capable of achieving a better balance of tensile properties in AlSi10Mg alloys.

Taking into consideration the seismic vulnerability of older buildings and the increasing need for reducing their carbon footprint and energy consumption, the application of an innovative system is investigated; the system is based on the use of textile reinforced mortars (TRM) and thermal insulation as a means of combined seismic and energy retrofitting of existing masonry walls. Medium scale tests were carried out on masonry walls subjected to out-of-plane cyclic loading. The following parameters were investigated experimentally: placement of the TRM in a sandwich form (over and under the insulation) or outside the insulation, one-sided or two-sided TRM jacketing and/or insulation, and the displacement amplitude of the loading cycles. A simple analytical method is developed and is found in good agreement with test results. Additionally, numerical modeling is carried out and is also found in good agreement with test results. From the results obtained in this study the authors believe that TRM jacketing may be combined effectively with thermal insulation, increasing the overall strength and energy efficiency of the masonry panels in buildings.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

Background: The Balaruc-les-Bains’ thermal mud was found to be colonized predominantly by microorganisms, with cyanobacteria constituting the primary organism in the microbial biofilm observed on the mud surface. The success of cyanobacteria in colonizing this specific ecological niche can be explained in part by their taxa-specific adaptation capacities, and also the diversity of bioactive natural products that they synthesize. This array of components has physiological and ecological properties that may be exploited for various applications.

Invasive species are significant threats to global agriculture and food security being the major causes of crop loss. An operative biosecurity policy requires full automation of detection and habitat identification of the potential pests and pathogens. Unmanned Aerial Vehicles (UAVs) mounted thermal imaging cameras can observe and detect pest animals and their habitats, and estimate their population size around the clock. However, their effectiveness becomes limited due to manual detection of cryptic species in hours of captured flight videos, failure in habitat disclosure and the requirement of expensive high-resolution cameras. Therefore, the cost and efficiency trade-off often restricts the use of these systems. In this paper, we present an invasive animal species detection system that uses cost-effectiveness of consumer-level cameras while harnessing the power of transfer learning and an optimised small object detection algorithm. Our proposed optimised object detection algorithm named Optimised YOLO (OYOLO) enhances YOLO (You Only Look Once) by improving its training and structure for remote detection of elusive targets. Our system, trained on the massive data collected from New South Wales and Western Australia, can detect invasive species (rabbits, Kangaroos and pigs) in real-time with a higher probability of detection (85–100 %), compared to the manual detection. This work will enhance the visual analysis of pest species while performing well on low, medium and high-resolution thermal imagery, and equally accessible to all stakeholders and end-users in Australia via a public cloud.

It is challenging to apply heat flow through a thermal bridge, which requires the analysis of 2D or 3D heat transfer to building energy simulation(BES). Research on the dynamic analysis of thermal bridges has been underway for many years, but their utilization remains low in BESs. This paper proposes a thermal bridge modeling and a dynamic analysis method that can be easily applied to BESs. The main idea begins with an analogy of the steady-state analysis of thermal bridges. As with steady-state analysis, the proposed method first divides the thermal bridge into a clear wall, where the heat flow is uniform, and the sections that are not the clear wall (the thermal bridge part). For the clear wall part, the method used in existing BESs is applied and analyzed. The thermal bridge part (TB part) is modeled with the linear time-invariant system (LTI system) and the system identification process is performed to find the transfer function. Then, the heat flow is obtained via a linear combination of the two parts. This method is validated by comparing the step, sinusoidal and annual outdoor temperature response of the finite differential method(FDM) simulation. When the thermal bridge was modeled as a third-order model, the root mean square error(RMSE) of annual heat flow with the FDM solution of heat flow through the entire wall was about 0.1W.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

In the power plant industry, the turbine inlet temperature (TIT) plays a key role in the efficiency of the gas turbine and, therefore, the overall—in most cases combined—thermal power cycle efficiency. Gas turbine efficiency increases by increasing TIT. However, an increase of TIT would increase the turbine component temperature which can be critical (e.g., hot gas attack). Thermal barrier coatings (TBCs)—porous media coatings—can avoid this case and protect the surface of the turbine blade. This combination of TBC and film cooling produces a better cooling performance than conventional cooling processes. The effective thermal conductivity of this composite is highly important in design and other thermal/structural assessments. In this article, the effective thermal conductivity of a simplified model of TBC is evaluated. This work details a numerical study on the steady-state thermal response of two-phase porous media in two dimensions using personal finite element analysis (FEA) code. Specifically, the system response quantity (SRQ) under investigation is the dimensionless effective thermal conductivity of the domain. A thermally conductive matrix domain is modeled with a thermally conductive circular pore arranged in a uniform packing configuration. Both the pore size and the pore thermal conductivity are varied over a range of values to investigate the relative effects on the SRQ. In this investigation, an emphasis is placed on using code and solution verification techniques to evaluate the obtained results. The method of manufactured solutions (MMS) was used to perform code verification for the study, showing the FEA code to be second-order accurate. Solution verification was performed using the grid convergence index (GCI) approach with the global deviation uncertainty estimator on a series of five systematically refined meshes for each porosity and thermal conductivity model configuration. A comparison of the SRQs across all domain configurations is made, including uncertainty derived through the GCI analysis.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

This study was conducted to improve the white index (WI) by preparing thermally expandable microspheres (TEMs) for wallpaper. The thermal properties, foam expansion ratio and WI were studied depending on the particle size of colloidal silica in the preparation of TEMs. As a result, the TEMs with small particles of colloidal silica showed the best results for whiteness and yellowing. Additionally, TGA results indicated that it was highly possible that colloidal silica with small particle sizes was physically or chemically attached to the surface of the TEMs that led to an improvement in whiteness at high temperatures.

The effects of carbon fiber hybridisation on the thermal properties of woven kenaf reinforced epoxy composites kenaf fibre were studied. Woven kenaf hybrid composites at the different weave designs of plain and satin, and fabric count of 5 × 5 and 6 × 6 were manually prepared by vacuum infusion technique. Thermal properties of pure carbon fibre and hybrid composites were conducted by using thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC). It was found that at high kenaf fibre content showed better thermal stability while the highest thermally stable was found in pure carbon fibre composite. The TG and DTG results showed that the amount of residue decreased in plain-designed hybrid composite compared to satin-designed hybrid composite. The DSC data revealed that the presence of woven kenaf increase decomposition temperature.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

The recyclability of polystyrene, acrylonitrile butadiene styrene, polystyrene and polyvinylchloride waste and using them as a source for 3D printing were studied. Filaments of about 3 mm in diameter were extruded successfully with a small-size extruder. The processed filaments were tested on a broad range of parameters - glass transition temperature, tensile properties and a pyrolysis scenario were obtained. The measured parameters were compared with parameters of virgin counterparts presented in the literature. In order to estimate the toxicity of the recycled material, elemental analysis of the samples was done.

In California, water is a perennial concern. As competition for water resources increases due to growth in population, California’s tree nut farmers are committed to improving the efficiency of water used for food production. There is an imminent need to have reliable methods that provide information about the temporal and spatial variability of crop water requirements, which allow farmers to make irrigation decisions at field scale. This study focuses on estimating the actual evapotranspiration and crop coefficients of an almond and pistachio orchard located in Central Valley (California) during an entire growing season by combining a simple crop evapotranspiration model with remote sensing data. A dataset of the vegetation index NDVI derived from Landsat-8 was used to facilitate the estimation of the basal crop coefficient (Kcb), or potential crop water use. The soil water evaporation coefficient (Ke) was measured from microlysimeters. The water stress coefficient (Ks) was derived from airborne remotely sensed canopy thermal-based methods, using seasonal regressions between the crop water stress index (CWSI) and stem water potential (Ystem). These regressions were statistically-significant for both crops, indicating clear seasonal differences in pistachios, but not in almonds. In almonds, the estimated maximum Kcb values ranged between 1.05 to 0.90, while for pistachios, it ranged between 0.89 to 0.80. The model indicated a difference of 97 mm in transpiration over the season between both crops. Soil evaporation accounted for an average of 16% and 13% of the total actual evapotranspiration for almonds and pistachios, respectively. Verification of the model-based daily crop evapotranspiration estimates was done using eddy-covariance and surface renewal data collected in the same orchards, yielding an r² >= 0.7 and average root mean square errors (RMSE) of 0.74 and 0.91 mm day^-1 for almond and pistachio, respectively. It is concluded that the combination of crop evapotranspiration models with remotely-sensed data is helpful for upscaling irrigation information from plant to field scale and thus may be used by farmers for making day-to-day irrigation management decisions.

Accumulative roll bonding (ARB) is one of methods of severe plastic deformation which is relevant for industrial production of sheets. While mechanical properties of several magnesium alloys subjected to ARB process have been studied, the physical properties have been reported only for some magnesium alloys. These properties are influenced by the texture developed during the ARB process and the temperature load. In the presented contribution, we studied thermal diffusivity and thermal conductivity of an AZ31 magnesium alloy after 1 and 2 passes through the rolling mill. Thermal diffusivity was measured with the laser-flash method in the temperature range between 20 and 350 °C. Thermal conductivity depends on the number of rolling passes. The microstructure and texture of sheets are significant factors influencing the thermal properties.

Burns is a pervasive and oppressive basic care issue. In children, burn injuries are a major reason for bleakness and mortality. The quirks in the physiology of liquid and electrolyte taking care of, the vital necessity and the distinctions in the different body extends in children direct that the pediatric wounds administration ought to be brought with an alternate point of view than for adults. Notwithstanding, for the intensivist, challenges regularly exist that muddle quiet help and adjustment. Moreover, burn injuries are mind-boggling and can show exceptional challenges that require deep-rooted recovery. Investigation in burn wound care has yielded progressions that will keep on improving practical recuperation. What's more, pain management all through this period is essential. Managing these wounds requires escalated therapeutic treatment for multi-organ dysfunction, and forceful surgical treatment to forestall sepsis and other inconveniences. The biological therapeutic bilayered skin substitutes with a long shelf life that recapitulates the normal barrier function of the intact human skin and stimulate wound repair and skin regeneration. A definitive objective is to accomplish a perfect skin substitute that gives a successful and without scar wound recuperating. This review article features the headway in pediatric burn wounds with an emphasis on the pathophysiology and treatment of burn wounds.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Spinal metastatic tumors are common and often cause debilitating symptoms. Image-guided percutaneous thermal ablation (IPTA) has gained significant recognition in managing spinal column tumors due to its exceptional precision and effectiveness. Conventional guidance modalities, including computed tomography, fluoroscopy, and ultrasound, have been important in targeting spinal column tumors while minimizing harm to adjacent critical structures. This study presents a novel approach utilizing a fusion of Cone Beam Computed Tomography with Magnetic Resonance Imaging to guide percutaneous thermal ablation for four patients with secondary spinal column tumors. The visual analog scale (VAS) evaluated procedure effectiveness during an 18-month follow-up. Percutaneous vertebroplasty was performed in two cases, and a thermostat was used during all procedures. Imaging was performed using the Stealth Station navigation system Spine 8 (SSS8) and a 1.5T MRI machine. The fusion of CBCT with MRI allowed precise tumor localization and guidance for thermal ablation. Initial results indicate successful tumor ablation and symptom reduction, emphasizing the potential of CBCT-MRI fusion in spinal column tumor management. This innovative approach is promising in optimizing therapy for secondary spinal column tumors. Further studies are necessary to validate its efficacy and applicability.

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

Urban heat islands and rising global temperatures are increasing the need for passive cooling solutions in densely populated areas. This study examines the effectiveness of heat-reflective paint in reducing surface and indoor temperatures in a 33-year-old apartment complex in Gumi City, South Korea. Using mock structures to simulate real building conditions, the experiment measured surface and indoor temperatures in both treated and untreated groups. Data collected from thermal imaging cameras and data loggers demonstrated significant temperature reductions on the treated walls, with surface temperatures lowering by 2.2°C to 4.3°C on average, and peak reductions of up to 15.3°C. Internally, the treated structures showed temperature reductions between 2.1°C and 4.1°C, with the largest difference observed during peak heat hours at 4.14°C. The results highlight the effectiveness of heat-reflective paint in mitigating heat stress and improving indoor thermal comfort, particularly in regions with high solar exposure. Importantly, this study aims to benefit vulnerable populations, such as the elderly and economically disadvantaged residents, by providing a cost-effective, sustainable solution to reduce heat exposure in aging urban buildings, thereby enhancing their quality of life.

In this study, hybrid materials were synthesized incorporating curcumin, Cu²⁺ or Fe³⁺, and Kappa-carrageenan as a reducing agent to improve its stability, considering that curcumin has low thermal and solution stability, which limits its applications. Colorimetric analysis showed color changes in the hybrids, ultraviolet-visible spectroscopy revealed band shifts in the hybrids, and infrared analysis indicated shifts in wavenumbers, suggesting changes in the vibrational state of curcumin after bonding with metal ions. These techniques confirmed the formation of the hybrid materials. Thermogravimetric and chromatographic analyses demonstrated greater thermal and solution stability for the hybrids compared to curcumin. Additionally, the hybrid composites effectively developed natural and sebaceous latent fingerprints with good clarity and contrast on glass surfaces. Both composites performed similarly to commercial gold powder. When applied to surfaces representative of forensic scenarios, the composites were versatile, revealing sufficient fingerprint details for human identification on both porous and non-porous surfaces. Scanning electron microscopy images showed greater clarity in sebaceous and natural fingerprints developed with the Fe composite compared to the Cu composite, due to minimal interaction of Fe with the glass surface.

This review discusses the key factors influencing the exceptional thermal resistance and surface properties of silicone-containing composites. Silicone polymers, known for their excellent chemical and physical proper-ties, are widely used in a number of innovative products. In order to make silicone composites suitable for innovative applications, it is essential to ensure that they have both very good thermal resistance and su-perhydrophobic properties. Identification of the key factors influencing these properties enables the use of these composites in coatings, electronics and photovoltaic panels. The discussion includes the role of or-ganosilicon polymer structures and the incorporation of micro- and nano-additives to enhance the perfor-mance of these materials. Different methods for the modification and production of silicone composites are analyzed, with an emphasis on achieving thermal stability and surface superhydrophobicity simultaneously. The review highlights the growing demand for silicone-based coatings, driven by technological advances and environmental concerns. Furthermore, the role of surface modification and hierarchical surface structures in achieving these unique properties is discussed, as well as the potential applications and challenges in the development of next-generation silicone-containing materials.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

Quantum thermal engines are receiving much attention in recent years, due to their potential applications.~For a candidate group, harmonically trapped gases under Bose-Einstein condensation (BEC), we see little investigation on the energy transference around that transition.~Therefore, we present an empirical study with rubidium-87 gas samples in a magnetic harmonic trap.~We developed an empirical Equation of State model to fit to our experimental dataset, expressing the pressure parameter ($\mathcal{P}$) in terms of temperature ($T$) and six technical coeffcients ($\{a_i\}_{0,\dots,4}$, $T_\mathrm{th}$), functions of volume parameter ($\mathcal{V}$) and number of atoms ($N$).~For weakly interacting gases, the internal energy is $U\cong3\mathcal{P}\mathcal{V}$, thus we determine the entropy with $U = TS - \mathcal{P}\mathcal{V}$ for fixed $N$.~As expected, we show that the entropy at the BEC transition ($S_c$) is constant for varying $\mathcal{V}$.~Being isentropic makes BEC transition an energy source for non-mechanical work.~Hence, we observed that the enthalpy at the BEC transition $H_c = E_c + \mathcal{P}_c\mathcal{V} = T_cS_c$, at fixed values of $\mathcal{V}$ and varying $N$, grows fairly linearly with $N$.~We fitted $H_c=\eta{N}-H_c^0$ to that data, being $\eta$ the specific enthalpy of BEC transformation and $H_c^0$ an intrinsic enthalpic loss.~We deem this study to be a step closer to practical quantum-based engines.

Many historic buildings and monuments on the Salento Peninsula (Apulia, southern Italy) were built from locally quarried Miocene calcarenites belonging to the Pietra Leccese Formation (Late Burdigalian-early Messinian). The main facies consists of a homogeneous and porous biomicrite, pale yellow in color and fine- to medium-grained, very rich in planktonic Foraminifera and massive or thick-bedded in outcrop. Additionally, there are other facies among which Piromafo stands out for its aesthetic appearance, which is enhanced by its greenish-brown or greenish-grey colors. Its physical characteristics, in terms of thermal properties mainly due to the mineral content and fabric, make it a good refractory and insulation material. Piromafo occurs in the upper part of the Pietra Leccese Fm. and is repre-sented by a fine- to medium-grained glauconitic and phosphatic biomicrite with macrofossils, es-pecially Bivalves and Gastropods. Despite its important historical use as building and ornamental material, especially in the Roman and Baroque architecture, a research gap exists in the scientific literature describing the properties of the stone and their correlation. Therefore, the aim of this paper is to present a wide range of properties useful to explain the in-situ behavior and damage susceptibility of the stone in monu-ments and buildings, but also for selecting preservation treatments and strategies. Thus, an overall assessment of the main petrophysical and mechanical properties especially for restoration/conservation purposes was performed using both standard and unconventional tech-niques. Starting from rock fabric inspection, particular attention was given to the relationship be-tween pore-size distribution and, hydraulic and thermal properties of the material. Unconfined compressive strength, flexural strength and indirect tensile strength were also estimated.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

Objective: The key to the success of pedicled skin flaps in the head and neck region is preserved perfusion. The use of thermal imaging can provide an indirect indicator of tissue perfusion, which consecutively would be of interest for perioperative prediction of the viability. The effectiveness of thermal imaging has already been demonstrated for assessing pedicled and free flaps [1]. This work investigates the implementation of SBTI as a noninvasive and cost-efficient method in clinical practice for predicting the vitality and perioperative monitoring of pedicled skin flaps in head and neck surgery. Methods: The FLIR One Pro camera was used for this pilot study (Teledyne FLIR LLC, Wilsonville, Oregon, United States). It is a multispectral camera that contains a near-infrared camera unit with a resolution of 160 x 120 pixels, a temperature range of 0 ° - 400 °C, and a thermal resolution of 70 millikelvin. For the study, after implementing the system, n = 11 skin flaps were photographed by SBTI (n=44) after marking (T1), after elevation (T2), after completed surgery (T3), and 24 hours postoperatively (T4), and the outcome was assessed clinically in correlation after one week by one surgeon. Results: The pedicled skin flaps examined all showed a preserved, uniform thermal image signature peri- and postoperatively for time points T1-4. This corresponded to a good postoperative result regarding the vitality of the tissue transfer in the clinical assessments 24 hours and one week postoperatively. Conclusion: The acquisition of a continuously obtained thermal image signature as a surrogate marker for preserved tissue perfusion by SBTI proved simple, inexpensive, noninvasive, and efficient in the present sentinel study. The application of SBTI has been primarily investigated in identifying perforators in large pedicled or free flaps. [2, 3] The concordance of the obtained thermal image signature with a positive clinical outcome suggests that the presented method is also suitable for perioperative prognostic statements on postoperative flap vitality in pedicled skin flaps and for monitoring those during surgery. Further studies are necessary for the implementation of this method in clinical practice to support the surgeon's intraoperative decision-making in the future.

Global climate change, particularly rising sea surface temperatures, profoundly impacts coral ecosystems, disrupting reproduction synchrony, symbiotic relationships with algae from the Symbiodiniceae family, and causing widespread bleaching and mortality among coral populations.  Oculina patagonica, a temperate scleractinian coral dominant in Mediterranean coastal waters, tolerates an annual temperature range of 10- 31°C. Moreover, in the past three decades, sea surface temperatures have rapidly risen in the Eastern Mediterranean Sea. O. patagonica offers insight into evolutionary adaptation to rapid environmental changes. This study investigated the effects of temperature changes on O. patagonica reproductive development, synchrony, and thermal sensitivity. Monthly monitoring of O. patagonica colonies for a year reveals no disruption in gonad development compared to previous studies, suggesting an unaffected sexual reproduction capacity. Thermal performance

The key to the practical application of organometal–halide–crystals perovskite solar cells (PSCs) is to achieve thermal stability through robust encapsulation. This paper presents a method to significantly extend the thermal stability lifetime of perovskite solar cells to over 5,000 h at 85 °C by demonstrating an optimal combination of encapsulation methods and perovskite composition for carbon–based multiporous–layered–electrode (MPLE)–PSCs. We fabricated the four types of MPLE-PSCs using two encapsulation structures (over– and side–sealing with thermoplastic resin films) and two perovskite compositions ((5–AVA)x(methylammonium (MA))1–xPbI3 and (formamidinium (FA))0.9Cs0.1PbI3), and analyzed the 85 ºC thermal stability followed by ISOS–D–2 protocol. Without encapsulation, FA0.9Cs0.1PbI3 exhibited higher thermal stability than (5–AVA)x(MA)1–xPbI3. However, encapsulation reversed the phenomenon (that of (5–AVA)x(MA)1–xPbI3 became stronger). The combination of (5–AVA)x(MA)1–xPbI3 perovskite absorber and over–sealing encapsulation effectively suppressed the thermal degradation, resulting in the PCE value at 91.2% of the initial value after 5,072 h. On the other hand, another combination (side–sealing on (5–AVA)x(MA)1–xPbI3, over– and side–sealing on FA0.9Cs0.1PbI3) resulted in decreased stability. The FA–based perovskite was decomposed for these degradation mechanisms by the condensation reaction between FA and carbon. For side–sealing, the space between the cell and the encapsulant was estimated to contain approximately 1,260,000 times more H2O than in over–sealing, which catalyzed the degradation of the perovskite crystal. Our results demonstrate that MA–based PSCs, which are generally considered to be thermally sensitive, can significantly extend their thermal stability after the proper encapsulation. Therefore, we emphasize that finding the appropriate combination of encapsulation technique and perovskite composition is quite important to achieve further device stability.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

This study aims to elucidate the influence of meteorological conditions on particle levels in Cergy-Pontoise. It explores the temporal variability of PM10 pollution days by associating them with the vertical temperature profile derived from conventional radiosondes from 2013 to 2022 (regional station). The results indicate that nearly 80% of exceedance days were associated with thermal inversions, primarily observed in winter and typically lasting 1 to 3 days. Analysis of winter thermal inversion characteristics suggests that those linked to pollution primarily occur near the ground, with higher intensity in December (12.1°C) and lower in February (10.3°C). Persistent inversions (extended nocturnal by diurnal inversion) account for 91.4% of the total inversions associated with high concentrations. Captive balloon soundings and temperature measurements at different altitudes were conducted during the winter of 2022/2023 to clarify thermal inversion in the Oise Valley at the center of Cergy-Pontoise. The results highlight three nocturnal wind circulation mechanisms in the valley, including downslope flow, circulation influenced by an urban heat island, and mechanical air evacuation under an inversion layer towards the less steep East side of the valley. Analysis of PM with the temperature gradient in the Oise Valley shows a significant correlation, suggesting an increase in concentrations during locally detected inversions and a decrease during atmospheric disturbance.

In order to assess the range of impact of thermal wastewater discharge from the third Nuclear Power Plant (NP_No.3) on the local ecosystem, a three-dimensional ocean model (MITgcm) driven by tidal and climatological forcings is employed to study the present work. Tides and daily wind forcings are incorporated into the MITgcm model to examine their effects on the thermal plume and the water circulation in Nan Wan Bay. The model results reveal that the thermal plume is most likely to disperse to the southwest in summer; it is unlikely to drift to the southeast or northeast because of the presence of gentle southwesterly monsoon. In winter, the thermal plume is most likely to be directed to the southwest but barely visible in the northeast or southeast directions because of prevailing northeasterly monsoon. Additionally, it is worth emphasizing that strong tidal currents generate a pair of counter-rotating eddies that significantly dominate the dispersal of the thermal plume. However, seasonal monsoons also play an essential role in modifying the plume’s direction and dispersion. The model results reveal that the flow field and thermal plume agree well with observational data.

Structural systems in housing projects contribute to the energy consumption of buildings during and after construction, and the climate plays a significant role in this energy consumption. Housing projects in harsh environments such in the United Arab Emirates (UAE) directly contribute to energy performance, specifically in low-density residential areas. By selecting the most efficient structural system, prior construction can enhance energy performance in such housing projects. The present study investigates the energy performance of three different structural systems used in UAE national housing: precast concrete, reinforced concrete, and light gauge steel (LGS). The case studies used for this study were constructed in Abu Dhabi, the capital of the UAE, specifically in Alain city. Second, through qualitative analysis and average annual billing of each housing project, the study identifies the thermal defects and determines the electricity consumptions of each system. The results indicate that the LGS system provides high thermal conductivity through its structural elements whereas reinforced concrete leads to the highest annual energy consumption in kW h/m². Finally, precast concrete has few thermal defects in its junctions and structural elements. The results indicate that LGS and reinforced concrete should be further studied, especially with regard to insulation and improvement, prior to implementation in housing systems.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

When wood is thermally modified, several chemical reactions take place that change the chemical and physical properties of the wood. These changes correlate with the degree of modification, which is mostly a function of temperature and duration of modification, and consequently with a mass loss during this process. There is a lack of standardized quality control to verify the degree of heat treatment of wood and thus its quality. One of the possible methods to check the degree of thermal modification of a particular type of wood is thermogravimetry (TG). It is based on the assumption that processes that did not take place during thermal modification continue when the TG experiment is carried out. In this method, calibration curves have to be established based on TG measurements of standard samples that have been thermally modified at different temperatures and whose mass loss during modification is known. The calibration curves show the mass loss during the TG measurement as a function of the mass loss during the previous thermal modification. The course of thermal decomposition during the TG measurements is influenced by many parameters, such as the mass of the sample, the heating rate, the atmosphere in which the measurement takes place, and the shape of the crucible in which the sample is placed. In this paper, the influence of these parameters on the calibration curves was investigated. We have focused on oak wood. The best parameters result in a calibration curve with the largest correlation coefficient R2 and the highest slope of the line k. On this basis, we can determine the mass loss during thermal modification of unknown samples of the same wood species under the same measurement conditions.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

We consider a real scalar field in de Sitter background and compute its thermal propagators. We propose that in a dS/CFT context, non-trivial thermal effects as seen by an `out' observer can be encoded in the anomalous dimensions of the d=3 Ising model. One of these anomalous dimensions, the critical exponent eta, fixes completely a number of cosmological observables, which we compute.

This work studied sorption regularities and assessed thermal stability and resistance to microbial degradation of humic acid as a result of 3 sorption cycles on bentonite clay, kaolinite, and muscovite using TGA/DSC, XRD, hydrophobic chromatography, light and electron microscopy, etc. The experiment revealed that kaolinite sorbed more humic acids (HAs) in terms of unit surface area (1.03 × 10-3 C, g/m2) compared to bentonite (0.35 × 10-3 C, g/m 10-3 g/m2). Sorption at pH 4.5 was accompanied by HA fractionation in amphiphilicity and chemical composition. HA was sorbed mainly due to hydrophobic components on the surface of all sorbents. HA was not intercalated into the interlayer spaces of montmorillonite during sorption. Sorption due to hydrophilic interactions was mostly performed on muscovite and bentonite than on kaolinite. Sorption was followed by a change in the chemical composition of HA and decreased C/N compared to free HA, indicating selective sorption of nitrogen-containing compounds which is most characteristic of muscovite. Only a relatively thermolabile HA fraction was adsorbed on all minerals while its thermal stability increased compared to that before the experiment. Thermal stability and ratio of the Exo2/Exo1 peak areas on the DSC curves of sorbed HA increased with each subsequent sorption cycle. Thermal stability and resistance to microbial oxidation of sorbed HA showed the following relationship: the higher the thermal stability, the less available is sorbed HA for utilization by microorganisms.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

The development of good conductivity p-type β-Ga2O3 is critical to realize its devices and applications. The nitrogen-doped p-type β-Ga2O3 films with enhanced conductivity characteristics were prepared through the thermal oxidation of GaN in the N2O atmosphere. Further measurements were performed on the oxidized films at 1000, 1050, and 1100 °C to have insight into the underlying mechanism of the thermally activated transformation process. The room temperature photoluminescence (PL) spectra demonstrated a moderate ultraviolet emission peak at 246 nm, confirming the generation of gallium oxide with a band gap of ~5.0 eV. The normalized X-ray diffraction (XRD), the high-resolution transmission electron microscopy (HRTEM), and the selected area electron diffraction (SAED) patterns were used to confirm the characteristic of polycrystalline and anisotropic growth. Then, the effects of the oxidation temperature on the amount of incorporated nitrogen were analyzed using secondary ion mass spectrometry (SIMS). Moreover, the ionization energy of the acceptor of films oxidized at 1000, 1050, and 1100 °C was calculated and analyzed using the temperature-dependent Hall test results. The results showed that nitrogen doping was the main contributor to p-type electrical properties. The activation energy of the polycrystalline β-Ga2O3 prepared through thermal oxidation of GaN in the N2O atmosphere was estimated to be 147.175 kJ·mol-1 using the Arrhenius plot, which was considerably lower than that of both dry and wet oxidations of GaN in O2 ambient, thus confirming the efficiency of thermal oxidation of GaN in N2O.

The study of energy sources has been an awareness of the modern world due to constraints on the current energy worldwide supply chain. The complexity of the theme as well as the consciousness of finite sources also the need of saving energy has become a priority. Although many papers have moved in this direction there is no record of papers studying the variables in a house heating system, which represents the highest energy consumption in many cold countries. This paper explores the energy-saving theme by studying the main variables present in houses’ heating systems in the winter season in cold countries like Canada, Russia, Norway, Iceland, Finland, etc. By using a novel combination of numerical thermal simulation by COMSOLTM and statistical analysis by MiniTabTM , it was possible to design an efficient thermal distribution in a house with the variables of the system by determining their significance and interaction qualitatively.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

The disc brake rotors are designed to withstand both, Maximum possible deceleration (emergency braking) and a series of frequent braking cycles. A effective rotor design and superior heat dissipating material provide better performance during the braking mechanism. In this experiment, modified ventilated disk brake rotors are developed with holes and slots and the stress, deformation, heat flux and temperature distribution has been analysed. Designing of the Finite element models of the rotor are created with SolidWorks and simulated using ANSYS. Structural and thermal characteristics are compared with a reference disk brake rotor of the motorcycle (TVS Apache RTR180). It is found that the modified rotors outperform the conventional one in terms of stress generation, temperature distribution and deformation. Furthermore, this Analysis helps us to find out the best suited material for one of the proposed designs. This experiment provides us an insight of the structural and thermal characteristics of the geometrically modified rotor that can be used to upgrade and outperform the current disc brake rotor used in the motorcycle (TVS Apache RTR180).

(1) Background: This article presents a study that aims to provide a precise understanding of the temperature distribution within a Whole-Body Cryostimulation (WBC) chamber, whether it is empty or occupied by one or several individuals.; (2) Methods: The study employs a mixed numerical and experimental approach, utilizing simplified Computational Fluid Dynamics (CFD) simulations and an experimental analysis that employs thermocouples to determine the 3D thermal field in actual conditions.; (3) Results: The results reveal a non-negligible temperature difference between the setpoint and actual temperature in the middle of the cryochamber. Furthermore, it is shown that the presence of individuals inside the chamber results in both an average temperature rise and a more heterogeneous thermal behavior, which appear to be associated with the number of individuals present.; (4) Conclusions: The findings of this study emphasize the need for further research to establish temperature guidelines and standardize measurement methods for effective WBC treatment.

1D spin crossover (SCO) solids which convert between the low-spin (LS) and the high-spin (HS) states are widely studied in the literature due to their diverse thermal and optical characters which allows obtaining many original behaviors, such as large thermal hysteresis, incomplete spin tran-sitions, as multi-step spin transitions with self-organized states. In the present work, we investigate the thermal behaviors of a system of two-elastically coupled 1D mononuclear chains, using the electro-elastic model, by including an elastic frustration in the nearest neighbors (nn) bond length distances of each chain. The chains are made of SCO sites that are coupled elastically through springs with their nn and next-nearest neighbors. The elastic inter-chain coupling includes diagonal springs, while the nn inter-chains distance is fixed to that of the high-spin state. The model is solved using MC simulations, performed on the spin states and the lattice distortions. When we only frustrate the first chain, we found a strong effect on the thermal-dependence of the HS fraction of the second chain, whose, by lowering its transition temperature which is also accompanied with the appearance of a significant residual HS fraction at low temperature. In the second step, we frustrate both chains by imposing different frustration rates and found that, for high frustration values, the thermal dependence of the total HS fraction exhibits three step and even four step spin transitions. The careful examination of the spin state structures in the plateau regions revealed the existence of special antiferro-elastic structure of type LSLS-HSHS-LSLS-HSHS along the first chain, and HSHS-LSLS-HSHS-LSLS along the second, also showing that the two chains seem to be antifer-ro-elastically coupled. This type of organization is interesting, because it anticipates the possible existence of periodic structures made of alternate 1D antiferro-like HS-LS strings coupled in the ferro-like fashion along the interchain direction in the 2D case.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

An increasing ecological phase-shift from coral dominated reefs to macroalgae dominated reefs as a result of anthropogenic impacts, such as eutrophication, sedimentation, and overfishing, has been observed in many reef systems around the world. Ocean warming is a universal threat to both corals and macroalgae, which may alter the outcome of competition between them. Therefore, in order to explore the effects of indirect and direct exposure to macroalgae on the physiological, biochemical, and genetic expression of corals at elevated temperature, the coral Acroproa hyacinthus and highly invasive green algae Caulerpa taxifolia have been chosen. Physiologically, the results exhibited that distinguish from control and direct contact treatments, the density and chlorophyll a content of zooxanthella decreased by 53.1% and 71.2% respectively, when coral indirect contacted with algae at ambient temperature (27°C). Besides, enzyme activities of superoxide dismutase (SOD) and catalase (CAT) in coral tissue were enhanced by interacting with algae. After an increase of 3°C, the density and chlorophyll a content of zooxanthella reduced by 84.4% and 93.8% respectively, whereas the enzmy activities of SOD and CAT increased by 2.3 and 3.1-fold. However, only the zooxanthellae density and pigment content decreased when C.taxifolia co-culture with A.hyacinthus at 30°C. Molecularly, different from the control group, the differentially expressed genes (DEGs) such as Rab family, ATG family and Casp7 were significantly enriched in endocytosis, autophagy and apoptosis pathways , regardless whether A.hyacinthus was indirect or indirect exposure to C.taxifolia at 27°C. Under thermal stress without algae interaction, the DEGs were significantly enriched in microbial immune signal transduction pathways, such as Toll-like receptor signaling pathway and TNF signaling pathway, while multiple cellular immunity (IFI47, TRAF family) and oxidative stress (CAT, SODC, HSP70) genes were up-regulated. Inversely, compared with corals without interaction with algae at 30°C, the DEGs of corals interacted with C.taxifolia at 30°C, were remarkably enriched in apoptosis, NOD-like receptor signaling pathway, including the transcription factors such as Casp family, TRAF family. In conclusion, the density and chlorophyll a content of zooxanthella remained a fading tendency induced by macroalgae at ambient temperature. The oxidative stress and immune response levels of coral has been elevated at 30°C, but macroalgae alleviated the negative effects triggered by thermal stress.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.