The tradeoff between the design phase and the experimental setup is crucial to satisfy the accuracy requirement of Large Deployable Reflectors. Manufacturing errors and tolerances change the RMS of the reflecting surface and require careful calibration of the tie rod system to be able to fit into the initial design specifications. To give a possible solution to this problem, here two calibration methods, respectively for rigid and flexible ring truss support, are described. Starting from the acquired experimental data on the net nodal coordinates, the initial problem of satisfying the static equilibrium at the measured configuration is described. Then, two constrained optimization problems, for rigid and flexible ring truss support, are defined to meet RMS accuracy of the reflecting surface modifying the tie lengths. Finally, a case study to demonstrate the validity of the proposed methods is presented.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

A distributed bragg reflector is designed to get an optical reflectance on visible electromagnetic spectrum i.e. ~800 nm in this work. Device is realized based on Abele’s matrix for TE mode.

The main central goal and statistical power of any statistical tool is to present the reader about the level, degree and strength of variations within or between datasets in a clear and precise interpretation that allows a researcher to make a rational and empirical conclusion. The current tools used for measure of dispersion have been challenged with some limitations. A new novel approach, called optinalytic (statistical) mirroring is proposed in this article to address some of the limitations other measure of dispersion methods have failed to solve and resolve. An optinalytic (statistical) mirrors are designed sequence images on which a sequence or set of sequences can optinalytically and intermetrically reflects to give an inferential information about their comparisons (similarity and dissimilarity). Method validation and comparisons with some most important tools of dispersion measures (e.g: variance, standard deviation, coefficient of variation, variance-to-mean ratio) was established to assess the suitability of the new proposal as an alternative measure of dispersion using different sets of logically generated univariate sequences with different problems and complications. The results of comparison shows that optinalytic (statistical) mirroring is more resistant to extreme outliers, more inferential and works efficiently with negative values with a very meaningful interpretation of result to the common understanding of a non-expert of statistics, which all other methods cannot provide.

Solar concentrator photovoltaic collectors are able to deliver energy at higher temperatures for the same irradiances, since they are related to smaller areas for which heat losses occur. However, to ensure the system reliability, adequate collector geometry and appropriate choice of the materials used for all their components will be crucial. The present study focuses on the re-design of the C-PV collector reflector currently produced by the Swedish company Solarus AB, together with a comparative analysis based on the annual assessment of the solar irradiance in the collector. An open-source ray tracing code (Soltrace) is used to accomplish the modelling of optical systems in concentrating solar power applications. Symmetric parabolic reflector configurations are seen to improve the PV system performance when compared to the conventional structures currently used by Solarus. The parabolic geometries, using either symmetrically or asymmetrically placed receivers inside the collector, achieve both the performance and cost-effectiveness objectives: for almost the same area or costs, the new proposals for the PV system may be in some cases 70 % more effective as far as energy output is concerned.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Computation of Common Middle Point seismic sections and their subsequent time migration and diffraction imaging provides very important knowledge about the internal structure of 3D heterogeneous geological media and are key elements for successive geological interpretation. Full-scale numerical simulation, that computes all single shot seismograms, provides a full understanding of how the features of the image reflect the properties of the subsurface prototype. Unfortunately, this kind of simulations of 3D seismic surveys for realistic geological media needs huge computer resources, especially for simulation of seismic waves’ propagation through multiscale media like cavernous fractured reservoirs. In order to significantly reduce the query of computer resources we propose to model these 3D seismic cubes directly rather than the shot-by-shot simulation with subsequent CMP stacking. To do that we modify the well known "exploding reflectors principle" for 3D heterogeneous multiscale media by use of the finite-difference technique on the base of grids locally refined in time and space. To be able to simulate realistic models and acquisition we develop scalable parallel software, which needs reasonable computational costs. Numerical results for simulation of Common Middle Points sections and their time migration are presented and discussed.