In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

Different bone bruise patterns observed on magnetic resonance imaging (MRI) after non-contact anterior cruciate ligament (ACL) rupture and lateral patellar dislocation may indicate different injury mechanism of knee. In order to investigate the typical bone bruising patterns after ACL rupture and patellar dislocation. In this study, 77 ACL rupture and 77 patellar dislocation patients’ knee MR images with bone bruises between August 2020 and March 2022at our institution were selected and analyzed, respectively. Sagittal and transverse planes images were used to determine the bone bruise location in the lateral-medial and superior-inferior directions of the MR images. The presence, location, and intensity of the bone bruises within specific compartments of the femur and tibial after ACL rupture and patellar dislocation were recorded. Relative bone bruise patterns of the ACL rupture and patellar dislocation were classified and analyzed. Results showed that there were 4 kinds of bone bruise (1-,2-,3-,4- bone bruises) patterns after ACL rupture. The most common two patterns after ACL rupture were 3- bone bruises (including lateral side of femur and both lateral and medial side of tibia, LF+BT; both lateral and medial side of femur and lateral side of tibia, BF+LT, medial side of femur and both lateral and medial side of tibia, MF+BT) followed by 4- bone bruises (both lateral and medial side of femur and tibia, BF+BT), 2- bone bruises (LF+LT, lateral side of femur and tibia; MF+LT, medial side of femur and lateral side of tibia; LF+MT, lateral side of femur and medial side of tibia; MF+MT, medial side of femur and tibia; 0+BT, both lateral and medial side of tibia;), and 1- bone bruise (0+LT, only lateral side of tibia). There was only 1 pattern bone bruise (latera femur and medial patella bone bruise) of patellar dislocation, the most common pattern of patellar dislocation was in the inferior medial patella and lateral anterior inferior femur. The results suggest that the pattern of bone bruise after ACL rupture and patellar dislocation is completely different. There were 4 kinds of bone bruise patterns after non-contact ACL rupture while there was only 1 kind of bone bruise pattern after patellar dislocation bone bruise patients which was in the inferior medial patella and lateral anterior inferior femur.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.