The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

The danger is still very large from cross site scripting attacks. When designing web applications We must follow as much as we can prevention rules and don’t leave any loophole to our programs. Experience is a great factor for programmers to know these attacks and for a trainee programmer is a difficult task to spot all the weak points. In this article we present a tutorial on launching an XSS attack and also we propose simple solutions.

The present work is focused on the numerical solution of the complete energy equation used in fluid film lubrication. The work was motivated by the fact the complete energy equation has no analytic solution that could be used for validations. Its accuracy and computation time are related to the employed numerical method and to the grid resolution. The natural discretization method (NDM) applied on different grids is systematically compared with the spectral method (the Lobatto Point Colocation Method or LPCM) with different polynomial degrees. A one dimensional inclined slider is used for the numerical tests and the energy equation is artificially decoupled from Reynolds. This approach enables to focus all the attention on the numerical solution of the energy equation. The results show that the LPCM is one or two orders of magnitudes more efficient than the NDM in terms of computation time. The energy equation is then coupled with Reynolds equation in a thermo-hydrodynamic analysis of the same 1D slider; the numerical results confirm again the efficiency of the LPCM. A thermo-hydrodynamic analysis of a two-lobe journal bearing is then presented as a practical application.

This article discuss the effects of heat treatment and lubrication modes on the machinability of an A356 alloy (Al-Si-Mg); the alloy is studied as-received, with solution heat-treated alloy (SHT) as well as with an alloy that is solution heat-treated and then aged at 155, 180 and 220 °C. In the course of machinability evaluation, several criteria including cutting force, surface roughness, tool wears and burr analysis (chip) were studied. The results and analysis in this work indicated that the selected machinability criteria are important and necessary to effectively evaluate the machinability of A356 alloys. The machinability of both materials and tools were estimated in terms of cutting force, chip thickness ratio and burr formation, flank wear and roughness. The effects of different cutting parameters (cutting speed and feed rate) and lubrication modes (dry, mist and wet) on the machinability of the A356 cast alloy were also examined. The influence of heat treatments on the burr formation and surface quality was clearly revealed by the experimental results. Experimental work revealed that cutting forces were influenced significantly by aging and cutting speed. However, the different aging at 155, 180, and 220 °C and the cutting speed significantly affected the machinability of the A356 cast alloy. The results obtained show that a better drilling performance in terms of surface quality occurs at a high feed rate, with dry drilling and artificial aging at T6.

A possible way to valorize citrus peels, which are byproducts of the juice extraction industry, is to use them as natural biopreservatives. In this paper we present early results from a compared Solvent Free Microwave Extraction (SFME) with Hydro-Distillation (HD) and Cold Pressing (CP) of essential oils (EOs) using fresh orange peel (Citrus sinensis L. var. Valencia late), a by-product in the production of orange juice in Algeria. The EOs were analyzed by gas chromatography coupled to mass spectrometry (GC-MS). All extracted C. sinensis EOs were chemotype limonene (94.64 to 95.48%). SFME is performed without added any solvent or water. SFME increases EO yield and eliminate wastewater treatment, resulting in a great progress in terms of time and cost efficiency. In its second part, the present study was conducted to evaluate “in vitro”, the antioxidant activities of Solvent Free Microwave (SFM) extracted orange EO by using the DPPH• (2,2-di-phenyl-1-picrilhydrazyl) free radical scavenging assay. The ability of orange EO to scavenge the free radical DPPH• was high, exceeding 80%. The result of the DPPH assay gives an IC₅₀ range value of 89.25 μg/mL (0.09 mg/mL) for the studied sample. Accordingly to the scientific literature, C. sinensis EO tested in the present study presented strong antioxidant activity, when looking to its values of AAI = 1.12 μg/mL. The feasibility of biopreservation used EOs as an alternative to synthetic techniques for liquid whole egg (LWE) stored under commercial retail conditions was investigated. The orange EO extracted by SFM was screened for its antibacterial and antioxidant activities in LWE at concentrations of 0.1, 0.3 and 0.5%. The TBA-RS results showed that the EO treatments significantly (p < 0.05) reduced the lipid oxidation in LWE. The long term oxidative, microbial and organoleptical stability of the LWE during display was positively influenced by orange EO treatments. Therefore, the results obtained here confirm that EO treatment as a promising technology to extend the commercial shelf-life of liquid egg products during retail/display.

The field of Cooperative Intelligent Transport Systems and more specifically Pedestrians to Vehicles could be characterized as quite challenging, since there is a broad research area to be studied, with direct positive results to society. Pedestrians to Vehicles is a type of Cooperative Intelligent Transport System, within the group of Early Warning Collision/Safety System. In this article, we examine the research and applications carried out so far within the field of Pedestrians to Vehicles Cooperative Transport Systems by leveraging the information coming from Vulnerable Road Users’, smartphones. Moreover, an extensive literature review has been carried out in the fields of Vulnerable Road Users Outdoor Localisation via smartphones and Vulnerable Road Users Next Step/Movement Prediction, which are closely related to Pedestrian to Vehicle applications and research. We identify gaps that exist in these fields that could be improved/extended/enhanced or newly developed, while we address future research objectives and methodologies that could support the improvement/development of those identified gaps.

Dynamic visualizations have been developed to exchange information that transforms over time across a broad range of professional and academic contexts. However, these visual tools may impose substantial demands on the learner’s cognitive resources that are very limited in current knowledge. Cognitive load theory has been used to improve learning from dynamic visualizations by providing certain design techniques to manage learner cognitive load without adding any oral/written explanations. This systematic review examined a series of experimental studies assessing the roles of these design techniques in learning tactical scenes of play through dynamic visualizations. Electronic databases PubMed and Google Scholar were used to search relevant articles. Eleven studies were eventually included for the systematic review based on the eligibility criteria. The present review revealed that adapting design techniques to the level of learners’ expertise, type of depicted knowledge, and level of content complexity is a crucial part of effective learning.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.