Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 0.8x1e6 Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer or simulant Urine) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 1.2x10⁶ Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10^-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

Our main objective in this work was to examine the possibility of non-intrusive, label-free, detection of whole Zika viruses using terahertz signals with or without a targeting/binding oligonucleotide (aptamers). We report for the first time the use of terahertz electromagnetic waves (0.75 THz – 1.1 THz) to detect Zika viruses. The Zika/aptamer complexes showed a reproducible terahertz reflection coefficient minimum at 1.064 THz while the Zika virus’s reflection minimum was at 1.073 THz. Of different substrates we examined, the polyester petri dish provided a very low loss and excellent terahertz transmission. To increase the interaction between the terahertz signal and the sample we also used polyester microbeads coated with aptamers. We then measured the terahertz reflection from the microbeads as a function of Zika concentration. The resulting terahertz Zika sensor had sensitivity of 63 Hz/Zika and minimum detectable signal of ~ 16x10³ Zika. Other substrates such as Graphene on polyethylene terephthalate (PET), 50 nm-thick gold film on polycarbonate, thin (30 um-thick) glass slide and Teflon were also examined. Graphene substrate enabled direct detection of the Zika without any aptamers.

This paper discusses a MEMS switch that can be fabricated using low temperature (<100^oC) deposition and patterning techniques suitable for the back-end-of-the-line integration with CMOS. The resulting cross-bar switches can be used for electrostatic discharge protection, FPGA implementation, chip security assessment and lock-down, and circuit block power management. We discuss platinum and iron switch with turn-on voltages of ~ 1.8 V. In the case of the iron switches, we also show that they can be magnetized to have “memory” and stay on when turned on. Platinum switch cycling of up to 1000 times did not show any changes in their turn-on voltage and their contact resistance was unchanged. The 10-100 nm switch airgaps were formed using low temperature sputtered sacrificial polysilicon and XeF₂ etching. XeF₂ does not attack any of the metals used in CMOS enabling fabrication of cross-bar switches with any of these metals. Once activated, it takes ∿ 6 to mechanically turn on the switch that can be decreased to ~1 ns by optimizing the device structure. Interestingly, the nm-scale gaps can be used as spark gap as a fast plasma switch to discharge first followed by the activation of the MEMS switch.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.