Leptospirosis is a zoonotic disease of global importance. The current killed vaccine provides serovar-specific protection without sterilizing immunity. Several surface antigens, including Leptospira immunoglobulin-like proteins (LigA and LigB), have been identified as subunit vaccine candidates; however, they require potent adjuvants. Bacterial Lipopolysaccharide (LPS), including lipid A, is a well-known immunostimulatory agent, and the formulation of Monophosphoryl Lipid A (MPLA) in Alum is a clinical adjuvant. Being less endotoxic, we tested the adjuvant activity of lipid A purified from L. interrogans serovar Pomona (PLA) for its ability to activate innate and enhance antigen-specific adaptive immune response. PLA-induced activation of macrophages similar to levels induced by MPLA, albeit at a much higher dose, indicating that it is less stimulatory than MPLA. Mice immunized with a Variable portion of LigA (LAV) formulated in Alum and PLA (LAV-Alum-PLA) induced significantly higher levels of LAV-specific humoral and cellular immune response than Alum but similar to levels induced by Alum-MPLA. The adjuvant activity of PLA seems to be quite similar to MPLA and primarily mediated through enhanced recruitment, activation, and uptake of antigens by innate immune cells. Moreover, like MPLA, the PLA formulation was able to generate a long-term memory response. Most importantly, PLA demonstrated better potency than MPLA formulation and generated sterilizing immunity against challenge in a hamster model of leptospirosis. Altogether, our study has provided important insight into the adjuvant activity of Leptospira lipid A and has opened avenues for the development of LPS-based vaccines against this dreadful zoonosis.

Laser-induced graphene (LIG) has gained considerable attention recently due to its unique properties and potential applications. In this study, we investigate using LIG in polyimide (PI) as a material for antenna applications. The LIG-PI composite material was prepared by a facile picosecond laser (1064 nm) irradiation process, which resulted in a conductive graphene network within the PI matrix. Furthermore, LIG formation was confirmed by Raman spectroscopy and sheet resistance measurements. Finally, a patch antenna from LIG for 2.45 GHz microwaves was simulated, produced and tested. These findings suggest that LIG-PI composites have great potential for use in high-frequency electronic devices and can provide a new avenue for the development of flexible and wearable electronics.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.