Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

Fractional differential mathematical model unfolding the dynamics of the COVID-19 pandemic in India is presented and explored in this paper. The purpose of this study is to estimate the future outbreak of disease and potential control strategies using mathematical models in India as a whole country as well as in some of the states of the country. This model is calibrated based on reported cases of infections over the month of April 2020 in India. We have used iterative fractional complex transform method to find approximate solutions of the model having modified Riemann Liouville fractional differential operator. We have also carried out a comparative analysis between actual and estimated cumulative cases graphically, moreover, most sensitive parameters for basic reproduction number$(R_0)$ are computed and their effect on transmission dynamics of COVID-19 pandemic is investigated in detail.

Curcumin attracts a huge attention because of its biological properties: antiproliferative, antioxidant, anti-inflammatory, immunomodulatory and so on. However, its usage has been limited by poor water solubility and low bioavailability. Herein, to solve these problems we developed curcumin-loaded nanoparticles based on end-capped amphiphilic poly(N-vinylpyrrolidone). Nanoparticles were obtained using the suspension method and were characterized by dynamic and electrophoretic light scattering, transmission electron microscopy and atomic force microscopy. The average particle size was 200 nm, and ζ-potential was -4 mV. Curcumin release studies showed that nanoparticles are stable in water solution. In vitro release study showed prolonged action in gastric, intestinal and colonic fluids, consistently and in PBS. In vitro studies on epidermoid carcinoma and human embryonic kidney cells showed that the cells absorbed more curcumin in nanoparticles compared to pure curcumin. Nanoparticles are safe for healthy cells and show high cytotoxicity for glioblastoma cells in cytotoxicity studies in vitro. Median lethal dose was determined in acute toxicity assay on Zebrafish and was 23 μM. Overall, the curcumin-loaded nanoparticles seem promising for cancer treatment.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.