Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

Objective: To evaluate the physical and chemical stability of the antibiotic temocillin at the recommended dose for severe infections and contained in infusion bags or elastomeric devices at different temperatures for its use in Outpatient Parenteral Antimicrobial Therapy (OPAT) programs.Method: Solutions of temocillin 12 g/L diluted in 0.9% sodium chloride were stored at 4ºC ± 2ºC, 25°C ± 2°C, 32°C ± 2°C and 37°C ± 2°C for 72 h both in polypropylene infusion bags and in polyisoprene elastomeric pumps. Physical and chemical stability were evaluated at 12, 24, 30 48 and 72 h after manufacturing. The solutions were considered stable if color, clearness and pH remained unchanged and if the percentage of intact drug was ≥90%. Results: There were no observed changes in color or clarity in any of the refrigerated (4°C) samples or in the samples incubated at 25ºC and 32ºC. At 37ºC, an increase in intensity of yellow color was observed at 30, 48 and 72 h in both infusion bags and elastomeric pumps samples. All samples remained within the pH range 6.84–6.06. At 4ºC, 25ºC and 32°C ± 2°C, temocillin attained the stability criteria of ≥90% of the original concentration for the whole experiment in both devices. At 37ºC, temocillin was stable for 24 h but its concentration dropped below 90% from that time point both in the infusion bags and in the elastomeric pumps.Conclusions: According to the data provided in this stability study, temocillin administrated by continuous infusion would be an appropriate candidate for the treatment of patients that can be discharge to complete therapy in an OPAT program.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.