In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

The research results conducted on binderless tungsten carbide (WC) ceramics obtained by Spark Plasma Sintering (SPS) of WC powders with different average particle sizes (0.095, 0.8, 3 μm) are presented. Nonuniform distribution of crystalline phases and microstructure of the WC ceramics was studied using layer-by-layer XRD analysis and SEM. Surface layers of the WC-based ceramics are characterized by nonuniform distribution of W2C crystalline phase and grain sizes, including the appearance of abnormally large grains. Thickness of the nonuniform layer was at least 50 μm. The effect under study is associated with an intense carbon diffusion from graphite foil. On the one hand, this contributed to a decrease in the intensity of W2C phase particle formation, which is transformed into α-WC phase due to the carbon. On the other hand, it caused abnormal grain growth in the layer where the carbon diffused. The obtained value of the carbon diffusion depth exceeds the values known from the literature (up to 1 μm in the case of volume diffusion even at temperature of 2370℃ and exposure time of ~ 60 h). The use of boron nitride (BN) as a protective coating on graphite mold parts did not prevent the formation of nonuniform layer on the ceramic surface.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Plaque psoriasis is a common, long-lasting illness that affects the immune system and causes significant negative impacts on a patient's physical health, well-being, and ability to work effectively. Deucravacitinib (DEU) is the first oral medication used in the treatment of plaque psoriasis, a chronic skin condition that causes red, scaly patches on the skin. DEU is a type of medication called an oral Janus kinase (JAK) inhibitor, which works by blocking specific enzymes that play a role in the inflammation and immune response associated with psoriasis. Therefore, a quick, easy, novel, reliable, sensitive, and straightforward Liquid Chromatography-Tandem Mass Spectrometry (LC-MS/MS) approach was used to analyse DEU in plasma samples. The LC-MS/MS method for the determination of DEU in human plasma was based on using trimethoprim as an internal standard (IS). The separation of DEU and IS was carried out via liquid-liquid extraction (LLE). The isolated substances were then subjected to the chromatographic system using the ACE-C18 column (4.6x100 mm, 5 µm). The mobile phase employed consisted of methanol and a solution of 2 mM ammonium formate (80:20 v/v, respectively). The flow rate used was set at 0.9 mL min-1. The creative strategy was performed by running an ABSCIEX API 4000 mass spectrometer with an electron spray ionization source in Multiple Reaction Monitoring (MRM) modes. The ion transitions m/z 426.3  358.2 was used for DEU quantitation, while the ion transitions m/z 291.1  261.1 was used for trimethoprim quantitation. The accuracy, precision, linearity, recovery, and selectivity of DEU were deemed acceptable when validated for a concentration range between 0.500 to 601.050 ng/mL, utilizing a weighting factor of 1/x2.

We present a compact polarimeter for 3He ions with special emphasis on the analysis of short-pulsed beams accelerated during laser-plasma interactions. We discuss the specific boundary conditions for the polarimeter, such as the properties of laser-driven ion beams, the selection of the polarization-sensitive reaction in the polarimeter, the representation of the analyzing-power contour map, the choice of the detector material used for particle identification, as well as the production procedure of the required deuterated foil-targets. The assembled polarimeter has been tested using a tandem accelerator delivering unpolarized 3He ion beams, demonstrating good performance in the few-MeV range. The statistical accuracy and the deduced figure-of-merit of the polarimetry are discussed, including the count-rate requirement and the lower limit of accuracy for beam-polarization measurements at a laser-based ion source.

The spray drying process causes the buildup of an unspecified and unique pattern of wall deposits on the wall. The powder recovery of fruit juice by spray dryer is associated with stickiness problems because of the nature of food which contains low molecular weight sugars and organic acids, which have a low glass transition temperature (T_g). The surface properties of oxygen plasma treated-PTFE substrate were evaluated by using the different parameters of Plasma Enhanced Chemical Vapour Deposition (PECVD) prior to spray drying analysis. In this study, the fabrication method of nearly perfect superhydrophobic surfaces through plasma treatment with oxygen gas was generated and utilized. The plasma-treated PTFE were deposited from a fixed flow rate of oxygen gas with 30 cm³/min by varying the deposition time from 1 to 15 minutes to induce the hydrophobic surface of the PTFE substrate. The characterization techniques used to determine the morphology and chemical bonding of the substrate are field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR), respectively. The hydrophobicity of the glass samples was determined by the water droplet contact angle. Sample prepared at radio frequency (RF) power of 90W for 15 minutes duration of treatment time showed porous and spongy like microstructure which correlates with the best performance of a good contact angle which creates the superhydrophobicity regime (171^o). Surface morphology analysis using scanning electron microscopy (SEM) showed changes in its roughness in the surface-treated glass substrate. The success of this method produced a huge potential for solving most of the food processing issues which relate to biofouling (e.g., powder stickiness) that would otherwise struggle to improve high productivity and recovery.

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

This paper deals with investigation of changes in geopolymer wettability with increasing mass fraction of high-carbon fly ash and surface treatment by cold atmospheric plasma (CAP). In this study, multiple samples of geopolymers were prepared, including those with 5% and 10% of high-carbon fly ash from coal-fired power station. Wettability of samples was then measured before and after plasma treatment, both on surface and cut surface. While addition of fly ash only had low effect on the wettability, as in most cases, it only lowered the initial contact angle without speeding up the speed of soaking for compact geopolymer and actually slowed the soaking for foamed geopolymer, plasma treatment had significant impact and made the geopolymer hydrophobic.

A technology for obtaining nanosized aluminum nitride powder by plasma-chemical synthesis is presented. Nitrogen gas (N2), melamine (C3H6N6) and ammonia (NH3) were used as a source of nitrogen. Aluminum powder of different fractions was used as a source of aluminum. The influence of the nitrogen source, the height of the injector, and the input power of the plasma equipment on the synthesized aluminum nitride powder is shown. The resulting aluminum nitride powder has a size d90=60 nm. The parameters of aluminum nitride synthesis did not in any way affect the granulometric composition of the synthesized powder materials. It was found that, due to the high binding energy, the nitrogen molecule (N2) reacts poorly with aluminum powder particles, as a result a mixture of nitrogen and ammonia gases was used in a ratio of 70/30 (mol.%) for aluminum nitride synthesis.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

The Planck Legacy recent release revealed a closed and positively curved early universe with a confidence level greater than 99%. In this study, the Friedmann–Lemaîtree–Robertson–Walker (FLRW) metric is enhanced to model early universe plasma, incorporating its reference curvature radius upon the emission of the cosmic microwave background (CMB) and the reference scale factor of the energy flux. The universe evolution from early plasma is modelled utilising quantised spacetime worldlines, where they revealed both positive and negative solutions implying that matter and antimatter in the plasma could be separated by electromagnetic fields and evolved in opposite directions as distinct sides of the universe, corroborating the CMB dipole anisotropy. The model indicates a nascent hyperbolic expansion is followed by a first phase of decelerating expansion during the first 10 Gyr, and then, a second phase of accelerating expansion. The model theoretically resolves the tension in Hubble parameter measurements, with a predicted density at the phase transition of 1.16. Further, it predicts a final time-reversal phase of rapid spatial contraction leading to a Big Crunch, signalling a cyclic universe. Simulations of the quantised spacetime continuum flux through its travel along the predicted worldlines demonstrated the fast-orbital speed of stars resulting from an external momentum exerted on galaxies via the spatial curvature through imaginary time dimension. These findings indicate that early universe plasma could be separated and evolved into distinct sides, collectively and geometrically influencing the universe evolution.

A new method of line shape calculations of hydrogen-like atoms in magnetized plasmas is presented. This algorithm makes it possible to solve two fundamental problems in the broadening theory: the analytical description of the radiation transition array between excited atomic states and account of a thermal ion motion effect on the line shapes formation. The solution to the first problem is based on the semiclassical approach to dipole matrix elements calculations and the usage of the specific symmetry properises of the Coulomb field. The second one is considered in terms of the kinetic treatment of the frequency fluctuation model (FFM). As the result one has a universal description of line shapes under the action of the dynamic of ion’s microfield. The final line shape is obtained by the convolution of the ionic line shape with the Voigt electron-Doppler profile. The method is applicable formally for large values of principle quantum numbers. However, it is demonstrated the efficiency of the results even for well known first members of the hydrogen Balmer series Dalpha and Dbeta. The comparison of obtained results with accurate quantum calculations is presented. The new method may be of interest for investigations of spectral line shapes of hydrogen-like ions presented in different kinds of hot ionized environments with the presence of a magnetic field, including SoL and divertor tokamak plasmas.

Background: Diabetes is a common non-communicable disease that is responsible for about 9% of all deaths and 25% reduction in life expectancy and nearly half of the diabetic patients are not aware of their disease. In this regard, diabetes screening to identify un-known diabetic patients is of great importance. Aims: The aims of this study were first to evaluate the performance of two commonly used diabetes screening tests that are currently recommended by the Iranian national screening program for diabetes (NSPD). Methods: The validities of the two diabetes screening tests were measured among 1057 participants older than 30 years. The studied screening tests included Capillary fasting blood glucose (CBG) and glycated hemoglobin (HbA1c). The golden standard for measuring the validity of the tests was venous fasting plasma glucose (VPG). Results: According to the results, the sensitivity of CBG and HbA1c tests were 69.01% and 84.5% and the specificity of the tests were 95.7% and 79.3% respectively. Positive and negative predictive values were 53.84% and 97.72% for CBG and 22.72% and 98.61% for HbA1c respectively. The recommended cut-points for CBG and HbA1c were 116.5 mg/dl and 7.15% respectively. Using these values as the new cut-points, sensitivity and specificity of CBG and HbA1c changed to 80.30% and 89.10%, and 77.50% and 94.20% respectively. Conclusions: Compared to several other countries, the performance of NSPD is relatively higher in Iran. ROC analysis suggested new cut-points for significantly better performance of NSPD.

Since the outbreak of SARS CoV-2 infection (Covid-19), healthcare professionals worldwide have been trying to find disease management and control alternatives to encourage immunotherapies. Immunotherapy is an efficient therapeutic option used against comparable viral contaminations such as MERS-CoV and SARS-CoV. The aim of the current study is to assess the existing knowledge associated with SARS-CoV-2 immunotherapy. Information available in published articles and their quality highlights the importance of following strict scientific rules for clinical outcomes. Thus, these studies have shown enough data to confirm that immunomodulation is the main topic investigated in research about Covid-19 therapy. Therefore, it is possible saying that immunotherapy is certainly the appropriate option against this virus.

Circulating tumor DNA (ctDNA) in fluids has gained attention because ctDNA seems to identify tumor-specific abnormalities, which could be used for diagnosis, follow-up of treatment, and prognosis: the so-called liquid biopsy. Liquid biopsy is a minimally invasive approach and presents the sum of ctDNA from primary and secondary tumor sites. It has been possible not only to quantify the amount of ctDNA but also to identify (epi)genetic changes. Specific mutations in genes have been identified in the plasma of patients with several types of cancer, which highlights ctDNA as a possible cancer biomarker. However, achieving detectable concentrations of ctDNA in body fluids is not an easy task. ctDNA fragments present a short half-life, and there are no cut-off values to discriminate high and low ctDNA concentrations. Here, we discuss the use of ctDNA as a cancer biomarker, the main methodologies, the inherent difficulties, and the clinical predictive value of ctDNA.

Objective: The primary objective of this trial was to assess the transfer of drospirenone to breast milk after daily administration of an oral test preparation containing 4 mg of drospirenone at the steady state. The secondary objective of the trial was to assess the safety of the preparation based on safety clinical and laboratory measurements (at the beginning and at the end of the trial) and reporting of adverse events and/or adverse drug reactions. Patients and Methods: This was an open label, non-comparative single center study. Drospirenone 4mg per day was the first postpartum contraceptive for the study participants who were no longer breastfeeding yet were still lactating. It was administered for 7 (seven) days to achieve steady-state concentration. All participants were volunteers who planned to use oral contraceptives as their family planning method in the future. Results: A total number of 12 volunteers completed the trial according to the protocol and the samples of all the 12 study completers were analyzed. The average concentration-time curve of drospirenone in plasma 24 h after the administration of the last dose (AUC(0-24h)) was 635.33 ng*h/mL and 120 h after the single repeat dose administration (AUC(0-120h) was 1180.57 ng*h/mL, respectively. The average Cmax was 48.64 ng/mL. The average concentration-time curve of drospirenone in milk 24 h after the administration of the last dose (AUC(0-24h)) was 134.35 ng*h/mL and 120 h after the single repeat dose administration (AUC(0-120h) was 227.17 ng*h/mL respectively. The average Cmax was 10.34 ng/mL. Conclusion: On average 18.13% of plasma drospirenone made it to breast milk and the highest concentration of drospirenone in breast milk was 17.55% of that in plasma. The total quantity of drospirenone passing to breast milk is on average 4478 ng during a 24 h period representing 0.11% of the maternal daily dose. Thus, at the recommended doses, no effects on breastfed newborns/infants are anticipated with drospirenone 4 mg.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

There is no simple method to measure glomerular filtration rate (GFR) in swine, an established model to study renal disease. We developed a protocol to measure GFR in conscious swine with the plasma clearance of iohexol. We used two groups: testing and validation, of 8 animals each. Ten milliliters of iohexol (6.47 g) were injected by the marginal auricular vein and blood samples (3 ml) were collected from the orbital sinus at different points after injection. GFR was determined considering two models: two-compartments (CL2: all samples) and one-compartment (CL1: the last six samples). In the testing group, CL1 overestimated CL2 by ~30%: CL2=245±93 and CL1=308±123 ml/mn. This error was corrected by a first order polynomial quadratic equation to CL1, which was considered the simplified method: SM=-47.909+(1.176xCL1)–(0.00063968xCL1²). SM showed narrow limits of agreement with CL2, and a concordance correlation of 0.97 and a total deviation index of 14.73%. Similar results were obtained for the validation group. This protocol is reliable, reproducible, can be performed in conscious animals, uses a single dose of the marker, and requires a reduced number of samples avoiding urine collection. Finally, it portends a significant improvement in animal-welfare conditions and handling necessities in experimental trials.

We explore the deflection angle in the framework of improved Schwarzschild Black hole utilizing the most advance geometrical path adopted by Gibbon-Werner. To investigate deflection angle of the photon ray by weak gravitational lensing for this black hole, we derive the optical curvature and perform the application of Gauss-Bonnet theorem on the optical metric. Moreover, we study the impacts of the plasma medium in context of the weak gravitational lensing in relate to this black hole. Further, we also study the graphical analysis of the deflection angle in both the plasma and non-plasma mediums. Also, we find the rigorous bound base upon the greybody factor for improved Schwarzschild black hole. A while later, we contrast our conclusions about deflection angle with the deflection angles of Schwarzschild black hole within plasma and non-plasma mediums.

Production and transport of reactive species through plasma-liquid interactions plays a significant role in multiple applications in biomedicine, environment, and agriculture. We experimentally investigated the transport mechanisms of hydrogen peroxide H2O2 and ozone O3, as the typical plasma species, into water. We measured the solvation of gaseous H2O2 and O3 in airflow into water bulk vs. electrosprayed microdroplets while changing the gas and water flow rates, applied voltage that determines the gas-liquid interface area, and treatment time. The solvation rate of H2O2 and O3 increased with the treatment time and the gas-liquid interface area. The total surface area of the electrosprayed microdroplets was larger than that of the bulk, but their lifetime was much shorter. We estimated that only microdroplets with diameters below ~ 40 µm could achieve the saturation by O3 during their lifetime, while the saturation by H2O2 was impossible due to its depletion from air. Besides the short-lived flying microdroplets, the longer-lived bottom microdroplets substantially contributed to H2O2 and O3 solvation in water electrospray. This study contributes to a better understanding of the gaseous H2O2 and O3 transport into water as a function of different parameters and will lead to design optimization of the plasma-liquid interaction systems.

In the upper charged layers of the atmosphere, the plasma is very rarefied. The collisions between its molecules are almost non-existent, and the driving forces behind them are the Lorentz forces resulting from the electric and magnetic fields. For this reason, we are interested in studying the behavior of non-collision plasmas because of its essential applications, such as the movement of satellites in the charged atmosphere. In this paper, the flow problem of collisionless gaseous plasma is examined. For that propose, we solve the unsteady Vlasov-Maxwell system of non-linear partial differential equations analytically. Methods of moments and traveling wave parameters are used to acquire an exact solution. Specific macroscopic properties of collisionless gaseous plasma are calculated along with electrical and magnetic fields. Further, thermodynamic estimation, such as entropy and entropy production, is presented. Those calculations allow us to measure the consistency with the laws of non-equilibrium thermodynamics. Relations between internal energy modification participations are predicted using Gibbs' equation for collisionless plasma. The modification effect of internal energies due to electro-magnetic fields is found to be small compared with the internal energy change due to the effect of entropy. That is because these fields are self-induced by plasma particles due to the sudden movement of the rigid plane plate. The results are accomplished according to the typical argon gaseous plasma model. Three-dimensional diagrams showing the measured variables are drawn to investigate and discuss their behavior. The problem has many commercial applications for the movement of objects in the charged atmosphere.

In this work, the degassing process of corn seeds was experimentally and numerically analyzed by removing air or other gases from around the seeds, specifically from the seed coating, in a rough vacuum chamber. The two complementary variants are employed to understand and optimize this process to improve the quality and germination rate of the seeds. Several experiments were conducted with well-established durations and masses of corn seeds at different temperatures to observe and record the behavior of the system, facilitating the modeling of the degasification process in the vacuum compartment. Modeling the degasification operation in the vacuum chamber allowed for determining the pressure profiles on the vacuum chamber and its lid. Numerical simulations were either conducted using a simulation program developed in the Visual Basic Applications (VBA) language for Microsoft Excel to model the degassing process in the vacuum chamber, or with the assistance of specialized software (transient structural analysis and simulation program in the ANSYS Workbench environment). Statistical analysis of the correlation between experimental and estimated pressure values revealed that both the proposed mathematical model and the solution method are well-chosen, with differences expressed through the absolute error (EA) being very small. Structural dynamic analysis carried through the Finite Element Method (FEM) highlights that the chosen materials for manufacturing the vacuum chamber vessel (316 stainless steel) or the chamber lid (transparent acrylic plastic) are durable and capable of withstanding the desired pressure and temperature demands in the seed treatment process. Additionally, through structural dynamic analysis, it was possible to study the deformation of system components, providing a detailed perspective on their structural distribution.

Background: Peyronie’s disease (PD) represents a challenging urological disease, due to not optimal post-operative surgical outcomes. We aim to evaluate if vacuum erection devices (VED) treatment before pe-nile curvature surgery is able to improve the post-operative surgical outcomes. Methods: All enrolled patients were assigned to the following groups: a) treatment group, VED treatment (3 times per week) starting 3 months before surgery and (3 times per week) one months after surgery and b) control group, VED treatment (3 times per week) one months after surgery. Follow-up urologic visits were scheduled at 3 and 6 months after surgery and the two groups were compared. Results: Thirty-eight patients have been enrolled (median age 67 years, 57-74, IQR), 20 in the treatment group and 18 in the control group. At the follow-up visits, the two groups are different in terms of IIEF-5 (26 vs 24; p=0.02), ‘yes’ to SEP2 and 3 (85% vs 55%; p<0.001, 85% vs 50%; p<0.001, respectively) and PDQ (-16 vs -11; p=0.03). Complete correction of penile curvature was achieved in 36 patients (94.7%). In the treatment group, no hourglass deformity has been reported, while in the control group 1 patient reported a mild hourglass deformity. In the treatment group, we obtained a longer total penile length (median +1.5 cm). The overall satisfaction rate was 98% in the treatment group and 96% in the control group. Conclusions: The VED treatment before penile curvature surgery in patients affected by PD is able to improve the post-operative surgery.

Imaginary dimensions in physics require an imaginary set of base Planck units and some negative parameter $c_n$ corresponding to the speed of light in vacuum $c$. Fresnel coefficients for the normal incidence of electromagnetic radiation on monolayer graphene introduce the second, negative fine-structure constant $\alpha_2^{-1} \approx -140.178$ as a fundamental constant of nature and this constant introduces these imaginary base Planck units along with this negative parameter $c_n \approx -3.06 \times 10^8~\text{[m/s]}$. Neutron stars and white dwarfs, considered as \emph{objects} emitting perfect black-body radiation, are conjectured to possess energy exceeding their mass-energy equivalence ratios, wherein the imaginary parts of two complex energies inaccessible for direct observation make storing excess of these energies possible. With this assumption, black holes are fundamentally uncharged; charged micro neutron stars and white dwarfs with masses lower than $5.7275 \times 10^{-10}~[\text{kg}]$ cannot be observed; and the radii of white dwarfs' cores are limited to $R_{WD} < 6.7933~G M_{WD}/c^2$, where $M_{WD}$ is a white dwarf mass. This sets the bounds on charged blackbody objects' minimum masses and maximum radii.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

The Vacuum Energy Parameter (VEP) of standard cosmology denotes the fraction of the critical density attributed to the accelerated expansion of the Universe. Astrophysical evidence sets the numerical range of VEP at 0.692 +, - 0.012, yet the root cause of these values is currently unknown. Drawing from the stochastic interpretation of early-Universe cosmology, we develop here a derivation of the VEP based on classical diffusion theory and the Langevin equation. Predictions are shown to be in reasonable agreement with observations.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

The Big Bang model is based on vague interpretations of experimental data. Direct interpretation of the data opens a new vision of the universe in a permanent dynamic equilibrium without beginning and without end. In the universe as the main system, the evolution of life on planet Earth is a consistent part of the universal process that operates in the entire universe. The origin of life as a consistent part of universal dynamics is in higher dimensions of the multidimensional dynamic quantum vacuum.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

Information-theoretically provable unique true random numbers, which cannot be correlated or controlled by an attacker, can be generated based on quantum measurement of vacuum state and universal-hashing randomness extraction. Quantum entropy in the measurements decides the quality and security of the random number generator (RNG). At the same time, it directly determines the extraction ratio of true randomness from the raw data, in other words, it obviously affects quantum random bits generating rate. In this work, we commit to enhancing quantum entropy content in the vacuum noise based quantum RNG. We have taken into account main factors in this proposal to establish the theoretical model of quantum entropy content, including the effects of classical noise, the optimum dynamical analog-digital convertor (ADC) range, the local gain and the electronic gain of the homodyne system. We demonstrate that by amplifying the vacuum quantum noise, abundant quantum entropy is extractable in the step of post-processing even classical noise excursion, which may be deliberately induced by an eavesdropper, is large. Based on the discussion and the fact that the bandwidth of quantum vacuum noise is infinite, we propose large dynamical range and moderate TIA gain to pursue higher local oscillator (LO) amplification of vacuum quadrature and broader detection bandwidth in homodyne system. High true randomness extraction ratio together with high sampling rate is attainable. Experimentally, an extraction ratio of true randomness of 85.3% is achieved by finite enhancement of the laser power of the LO when classical noise excursions of the raw data is obvious.

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

Gene expression variations of plant leaf are investigated by irradiating seed and leaf with oxygen or air plasmas. Enhancement of leaf growth is induced by oxygen plasma irradiation on seeds, which is supported by increased gene expression for protein synthesis, oxidative-reduction reactions and decreased gene expression concerning DNA methylation and histone modification. Suppression of leaf growth is observed by the oxygen plasma, which would be owing to increased gene expression concerning heat shock protein and redox reaction, and decreased expression of photosynthesis and glycoprotein. Also, gene expression variation due to air plasma irradiation is almost same as that of oxygen plasma. Active oxygen species are major factors in both oxygen and air plasmas for the variation of gene expressions in plant.

This article reports new measurements of laser-induced plasma hypersonic expansion measurements of diatomic molecular cyanide (CN). Focused, high-peak power 1064-nm Q-switched radiation of the order of 1 TW/cm² generates optical breakdown plasma in a cell containing a 1:1 molar gas mixture of N₂ and CO₂ at a fixed pressure of 1.1 × 10⁵ Pascal and in a 100 ml/min flow of the mixture. Line-of-sight (LOS) analysis of recorded molecular spectra indicate the outgoing shockwave at expansion speeds well in excess of Mach number 5. Spectra of atomic carbon confirm an increased electron density near the shock wave, and equally, molecular CN spectra reveal higher excitation temperature near the shockwave. The results are consistent with corresponding high-speed shadow graphs obtained by visualization with an effective shutter speed of five n anosecond. In addition, LOS analysis and application of integral inversion techniques allow inferences about the spatio-temporal distribution of the plasma.

Despite recent advancements, therapies remain ineffective against advanced oral squamous cell carcinoma (OSCC), resulting in unsatisfactory therapeutic outcomes. Cold atmospheric plasma (CAP) offers a promising approach in the treatment of malignant neoplasms. Yet, the exact mechanisms driving CAP-induced cancer cell death are not fully understood. This study revealed a significant reduction in the viability of OSCC cell lines, inactivation of AKT and ERK, and the downregulation of the miR-21, miR-31, miR-134, miR-146a and miR-211 expression followed the CAP treatment. Pretreatment with ZVAD, 3-MA, and Fer-1 synergistically reduced CAP-induced cell death, indicating a combined induction of variable death pathways by CAP. Activation of AKT and ERK, alongside combined treatments using death inhibitors and miRNA mimics, counteracted the cell mortality associated with CAP. CAP-induced downregulation of miR-21, miR-31, miR-187 and miR-211 expression was rescued by AKT and ERK activation. Additionally, CAP treatments notably inhibited the growth of SAS cell xenografts on nude mice. The reduced expression of oncogenic miRNAs in vivo aligned with in vitro findings. In conclusion, our study indicates that CAP jet treatment diminishes OSCC cell viability by abrogating survival signals and oncogenic miRNA expression.

An analysis of the relationship between plasma cytokines and the effectiveness of treatment with TNFαinhibitors was performed in 81 patients with moderate-to-severe psoriasis. Treatment efficacy was assessed by PASI score, and patients were classified into a positive effect (PASI≥75) and no effect group (PASI≤50). A positive effect was reached in 11 (41%) patients for etanercept, 14 (52%) for adalimumab, and 26 (96%) for infliximab. Data analysis did not show  differences in baseline TNFα levels and subsequent treatment effectiveness. The CART algorithm showed that at the baseline level of VEGF ≥ 32 pg/ml and IL17F &lt; 26 pg/ml, there was an 83% probability of a positive effect. Random forest analysis showed the importance of VEGF, ICAM1, sCD40L, IL17F and IL31 baseline levels in the prediction of treatment effectiveness.   Significant differences between the groups before/after the treatment were found only for TNFα: the median values were more than 50 times higher in no effect compared with positive effect group. There were differences before/after therapy in the levels of IL20, ICAM1, IL22, IL23 in the no effect group. The treatment affected the cytokine profile in most cases regardless of the effectiveness of therapy.

Tissue programmed death ligand-1 (PD-L1) protein is the recognized predictive immune biomarker of immune checkpoint inhibitor (ICI) treatment benefit in metastatic non-small cell lung cancer (NSCLC). However, tissue PD-L1 protein testing can be limited by tumor heterogeneity and fraught with tissue acquisition difficulties. A plasma PD-L1 assay potentially overcomes these tissue limitations. Patients with metastatic NSCLC treated with first-line ICI-based treatment and available results of plasma cfRNA PD-L1 by real-time polymerase chain reaction (RT-PCR) and tissue PD-L1 protein PD-L1 with the Dako 22C3 monoclonal antibody were retrospectively assessed for median and landmark 3-year overall survival (OS). OS was identical whether positive plasma cfRNA PD-L1 expression or positive tissue PD-L1 protein expression (median OS 15 months; 3-year landmark OS 30%; hazard ratio (HR) 0.97; 95% CI, 0.44-2.10). Positive plasma cfRNA PD-L1 patients also demonstrated a numerically longer median and higher 3-year OS compared to patients lacking PD-L1 expression (median 15 months versus 8 months; 3-year landmark OS 30% versus 15%; HR 0.56; 95% CI, 0.27-1.17). Plasma cfRNA PD-L1 expression by RT-PCR was similarly predictive of ICI-based treatment benefit as tissue PD-L1 protein expression.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

In this study, a simple, easy and convenient fluorescent sensing system for detection of vascular endothelial growth factor (VEGF) based on VEGF aptamers, aptamer-complementary fluorescence-labeled probe and streptavidin magnetic beads was developed in only one single tube. The VEGF is the most important biomarker in cancer angiogenesis, and is investigated that serum VEGF level was various according to the different type and course of cancers. Hence, efficient quantification of VEGF is able to improve the accuracy of cancer diagnosis and precision of disease surveillance. In this research, the VEGF aptamer was designed to be able to bind with the VEGF by forming G-quadruplex secondary structures, and then the magnetic beads would capture the none-binding aptamers due to none steric interference, and finally, the fluorescence-labeled probes were hybridized with the aptamers captured by the magnetic beads. Therefore, the fluorescent intensity in the supernatant would specifically reflect the present of VEGF. After an overall optimization, the optimal conditions for detection of VEGF were as followed, KCl, 50 μM; pH 7.0; aptamer, 0.1 μM and magnetic beads, 10 μL (4 μg/μL). The VEGF could be well quantified within a range of 0.2-2.0 ng/ml in plasma, and the calibration curve possessed a good linearity (y = 1.0391x + 0.5471, r = 0.998). The detection limit (LOD) was calculated to be 0.0445 ng/mL according to the formula (LOD = 3.3×σ/S). The specificity of this method was also investigated under the appearance of many other serum proteins, and the data showed the good specificity in this aptasensor-based magnetic sensing system. This strategy provided a simple, sensitive and selective biosensing platform for detection of serum VEGF. Finally, it was expected that this detection technique can be promoted to more clinical applications.

KDEL receptor-1 maintains homeostasis in the early secretory pathway by capturing and retrieving ER-chaperones to the ER during heavy secretory activity. We have previously shown that a Golgi scaffolding protein (ACBD3) facilitates KDEL receptor localization at the Golgi via regulating cargo wave-induced cAMP/PKA-dependent signaling pathway. Unexpectedly, a fraction of the receptor is also known to reside in the plasma membrane as a stress response, although it is largely unknown exactly how KDEL receptor gets exported from the Golgi and travels to the PM. In this study, we sought to investigate the mechanism by which KDEL receptor gets exported from the Golgi en route to the PM and identified two crucial factors that greatly influence post-Golgi trafficking of KDEL receptor. We show here that ACBD3 depletion results in significantly increased trafficking of KDEL receptor to the PM via Rab4-positive tubular carriers emanating from the Golgi. Expression of constitutively activated Rab4 mutant (Q72L) increases surface expression of KDEL receptor up to 2~3-fold, whereas expression of GDP-locked Rab4 mutant (S27N) inhibits KDEL receptor localization to the PM. Importantly, KDELR trafficking from the Golgi to the PM is independent of PKA- and Src Kinase-mediated mechanism. Taken together, these results reveal that ACBD3 and Rab4-GTP are key players at the Golgi in regulating KDEL receptor trafficking to the cell surface.

The scope of this work was part of our previous research on Pulsed Power Plasma Stimulation Technique. Electromagnetic fields generated during a pulsed power plasma discharge were simulated using a finite element method in the COMSOL RF module. The field distributions were calculated during and after the pulse. The current paper takes advantage of prior work measuring and modeling the current distribution in the plasma arc. Agreement with laboratory experimental measurements provides support for extension of the model to reservoir scale. The validated model was used to quantify the signal attenuation level in different medium environment.

(1) Background: We reviewed the logistics of the implementation of pathogen inactivation (PI) using the INTERCEPT Blood System™ for platelets and the experience with routine use and clinical outcomes in the patient population at the Sírio-Libanês Hospital of São Paulo, Brazil. (2) Methods: Platelet concentrate (PC), including pathogen reduced (PR-PC) production, inventory management, discard rates, blood utilization, and clinical outcomes were analyzed over the 40 months before and after PI implementation. Age distribution and wastage rates were compared over the 10 months before and after approval for PR-PC to be stored for up to 7 days. (3) Results: A 100% PR-PC inventory was achieved by increasing double apheresis collections and production of double doses using pools of two single apheresis units. Discard rates decreased from 6% to 3% after PI implementation and further decreased to 1.2% after 7-day storage extension for PR-PCs. The blood utilization remained stable, with no increase in component utilization. A significant decrease in adverse transfusion events was observed after the PI implementation. (4) Conclusion: Our experience demonstrates the feasibility for Brazilian blood centers to achieve a 100% PR-PC inventory. All patients at our hospital received PR-PC and showed no increase in blood component utilization and decreased rates of adverse transfusion reactions.

It is widely, but not universally, believed that the lipids of the plasma membrane are not uniformly distributed, but that "rafts'' of sphingolipids and cholesterol float in a "sea'' of unsaturated lipids. The physical origin of such heterogeneities is often attributed to a phase coexistence between the two different domains. We argue that this explanation is untenable for several reasons. Further we note that the results of recent experiments are inconsistent with this picture. However they are quite consistent with an alternate explanation, namely that the plasma membrane is an emulsion of the two kinds of regions. To show this, we briefly review a simplified version of this theory and its phase diagram. We also explicate the dependence of the predicted domain size on four physical parameters. Among them are the spontaneous curvature of the membrane and its bending modulus and surface tension. Taking values of the latter two from experiment, we obtain domain sizes for several different cell types that vary from 58 to 88 nm.

The Boltzmann-Gibbs (BG) entropy has been used in a wide variety of problems for more than a century. It is well known that BG entropy is extensive, but for certain systems such as those dictated by long-range interactions, the entropy must be non-extensive. Tsallis entropy possesses non-extensive characteristics, which is parametrized by a variable q (q = 1 being the classic BG limit), but unless q is determined from microscopic dynamics, the model remains but a phenomenological tool. To this date very few examples have emerged in which q can be computed from first principles. This paper shows that the space plasma environment, which is governed by long-range collective electromagnetic interaction, represents a perfect example for which the q parameter can be computed from micro-physics. By taking the electron velocity distribution function measured in the heliospheric environment into account, and considering them to be in quasi equilibrium state with electrostatic turbulence known as the quasi-thermal noise, it is shown that the value corresponding to q = 9/13 = 0.6923 may be deduced. This prediction is verified against observation made by spacecraft, and it is shown to be in excellent agreement.

During the long-term operation of the plasma reactor, decreases in the plasma concentration were noticed despite the constant maintenance of all parameters. One of the factors is the decrease of the nitrogen content on the surface of the electrode, in order to eliminate it, the supply voltage has been increased to 11 kV. The next decisive factor in the decrease of plasma concentration is the oxidation of the electrode surface, therefore two electrodes were used: first one with solid gold and the other one copper covered with galvanized gold with a thickness of 10 μm. During the experiment, a large decrease in plasma concentration was observed when the electrode coated by gold was used. High-energy electrons have knocked out the gold atoms from the electrode, as a result of which the gold evaporated and the raids layers formed. After a month of working of the electrodes, metallographic researches were carried out, the results of which are described in this publication.

In order to achieve better knowledge of the thermal barrier coatings (TBCs) by supersonic atmospheric plasma spraying (SAPS) process, an experimental study was carried out to elaborate physicochemical properties of particles in-flight during the SAPS process. One type of commercially available agglomerated and sintered yttria-stabilized-zirconia (YSZ) powders were injected into the SAPS plasma jet and collected by shock chilling method. The YSZ particles in-flight physicochemical properties of the melting state, morphology, microstructure, particle size distribution, element composition changes and phase transformation during the SAPS process have been systematically analyzed. The melting state, morphology and microstructure of the collected particles were determined by scanning electron microscopy (SEM). The particle size distribution was measured by a laser particle size analyzer (LPSA). Element compositions were quantitatively analysed by an electron probe X-ray microanalyzer (EPMA). Additionally, the X-ray diffraction (XRD) method was used to analyse the phase transformation. The results showed that the original YSZ powders injected into the SAPS plasma jet were quickly heated and melted from the outer layer companied with breakup and collision-coalescence. The outer layer of the collected particles containing roughly hexagonal shaped grains exhibited a surface texture with high sphericity and the inside was dense with hollow structure. The median particle size was decreased from 45.65 μm to 42.04 μm. Besides, phase transformation took place and the content of zirconium (Zr) and yttrium (Y) element was decreased with the evaporation of ZrO2 and Y2O3.

Cell-based therapies and tissue engineering applications require biocompatible substrates that support and regulate the growth, survival, and differentiation of specific cell types. Extensive research efforts in regenerative medicine are devoted to the development of tunable biomaterials which support various cell types including stem cells. In this research, the non-cytotoxic biopolymer polycaprolactone (PCL) was fabricated into 2D and 3D scaffolds with or without the low-pressure oxygen plasma treatment to enhance hydrophilicity. Cellular responses and biocompatibility were evaluated using a human Wharton’s jelly mesenchymal stem cell line (BCP-K1). The 2D PCL scaffolds enhanced initial cell attachment compared to the 3Ds indicated by a higher expression of focal adhesion kinase (FAK). Whilst, the 3D scaffolds promoted cell proliferation and migration as evidenced by higher cyclin A expression and filopodial protrusion, respectively. The 3D scaffolds potentially protected the cell entering to apoptosis/necrosis program and induced cell differentiation, evaluated by gene expression. Both 2D and 3D PCL appeared to have stronger effects on cell behavior than a control substrate (polystyrene). In summarize, the different configuration and surface properties of PCL scaffolds provide various options for modulation of stem cell behaviors, including attachment, proliferation, survival, and differentiation, when combined with specific growth factors and culture conditions.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

Metabolomic analysis of biological fluids and tissues has become an increasingly routine tool in the biological toolbox. However, challenges remain to be overcome, including developing strategies to maximise coverage of the metabolome without requiring large sample volumes. Here we describe a multimodal strategy that combines data using both LC-MS and GC-MS from a unique vial with a sample of plasma (20µl) or a sample of brain tissue (3mg). Using a split phase extraction the non-aqueous phase was analyzed by reversed phase (RP) LC-MS, whilst the aqueous phase was analyzed using hydrophilic liquid interaction chromatography (HILIC)LC-MS, with both phases also analysed using GC-MS after derivatization of the extract. Analytical performance was assessed in 7 rat cerebellum samples and a pilot study of 40 plasma samples (20 vs. 20: AD vs. healthy controls). The method, which uses four hours of instrument time, measured 20,707 metabolite features in brain samples and 17,266 in plasma samples, from those 44.1% features displayed CV’s below 15% and 75.2% below 30%. The method has potential to resolve subtle biological differences and to correlate metabolite composition directly to clinical outcomes including MMSE, age and ADCS-ADL. This method can acquire in the order of 20K metabolic features when low volumes are available.

The debate about the meaning of life in the literature has been around for a while and portraits a fundamental human need to find a personal path of existence. The meaning of life phenomenon purpose lies in its impact on the psychological wellbeing. Knowing your purpose in life can make it more structured and in balance, therefore more meaningful and comprehensible. However, in the existing body of the academic literature meaning of life is discussed more from the philosophic perspective rather than a practical area, which is not helping to solve the global issues of increasing mental health problems. When social and emotional wellbeing is being affected, it is urgent to apply a practical approach to effectively overcome these states. Introduction of a new, holistic meaning of life model is an attempt to offer a practical solution for society to maintain their mental health through awareness of their life’s purpose. Previously in the pilot study (Dombrovskis, 2017) in a sample group of 100 citizens of Latvia who self-reported being in a crisis situation at the given moment, using qualitive analysis the first component for the model structure was identified – antecedent. In our research antecedent is defined as something that triggers certain action, so in crisis situation person can regain a structure and stability in life. We found 8 different antecedents that trigger behavior of those affected by crisis: achievements; power; success; development; freedom; uniqueness; interesting life and fleeing. To continue to explore other components for our model in the setting of Latvia, this study aims to investigate the demographic and personality related variables that may serve as antecedents and as such become one of component in our model structure. The study used a sample of residents of Latvia representing the total population of 1,110 respondents (633 women, 57%, and 477 men, 43%) who have completed the self-assessment questionnaire Meaning of life scale (MOLS) (online and frontally) designed by the authors on their satisfaction with different factors regarding the meaning of life. Average age of respondents (M=33.88; SD=8,527) varied from 18 to 67. The exploratory and confirmatory analysis confirms the data regarding existence of totally 16 factors: 8 antecedents identified in the pilot study and 8 new antecedents identified in the present study - family relations; level of income; relations with friends/acquaintances; state of health; organization of free time; career growth (achievements); sexual life quality and quality of education. Findings confirm a model’s structure to be complex phenomenon consisting of various components. However, findings suggest that more research should be done to fill the following gaps: 1) identify actions, which are triggered by 16 antecedents; 2) figure out F1, F2 and F3 factor role in the model structure.

The high Nb-containing TiAl-based alloy ingot beyond laboratory scale with a composition of Ti-46Al-8Nb (at. %) was prepared by a vacuum induction melting process based on BaZrO3 refractory. An ingot without macroscopic casting defects (such as pipe shrinkage and center line porosity) was finally obtained, and the chemical composition, solidification path, microstructure and tensile properties of the ingots were investigated. The results show that the deviations of Al and Nb content along a 430 mm long central part of the ingot are approximately \mathrm{\pm}0.39 at. % and \mathrm{\pm}0.14 at. %, and the oxygen content in the ingot can be controlled at around 1000 ppm. During the solidification process, the alloy suffered from peritectic reaction and formed columnar grains with anisotropy. In addition to Al segregation and Nb segregation, β-phase particles associated with γ phase at the triple junction of the colonies were observed. Moreover, the mechanical properties of the ingot in the transverse direction are significantly better than those in the longitudinal direction, with a tensile strength of up to high as 700 MPa and a corresponding fracture elongation of 1.1 %.

The effect of Zr addition on the melting temperature of the CoCrFeMnNi High Entropy Alloy (HEA), known as the “Cantor’s Alloy”, is investigated, together with its microstructure, mechan-ical properties and thermo-mechanical recrystallization process. The base and Zr-modified al-loys are obtained by vacuum induction melting of mechanically pre-alloyed powders followed by recrystallization. The alloys were characterized by X-ray diffraction, scanning and transmis-sion electron microscopy, thermal analyses, mechanical spectroscopy and indentation measures. The main advantages of Zr addition are: 1) a fast vacuum induction melting (VIM) process; 2) the lower melting temperature, due to Zr eutectics formation with all the Cantor’s alloy elements; 3) the good chemical alloy homogeneity; 4) the mechanical properties improvement of recrystallized grains with a coherent structure. The crystallographic lattice of both alloys resulted to be FCC. Results demonstrate that the Zr-modified HEA presents a higher recrystallization temperature and smaller grain size after recrystallization with respect to the Cantor’s alloy, with precipita-tion of a coherent second phase which enhance the alloy hardness and strength, while maintaining a good tensile ductility.

When solving the Einstein's equations for an isolated system of masses, V. Fock introduces harmonic reference frame and obtains an unambiguous solution. Further, he concludes that there exists a harmonic reference frame which is determined uniquely apart from a Lorentz transformation if suitable supplementary conditions are imposed. It is known that wave equations keep the same form under Lorentz transformations. Thus, we speculate that Fock's special harmonic reference frames may have provided us a clue to derive the Einstein's equations in some special class of non-inertial reference frames. Following this clue, generalized Einstein's equations in some special non-inertial reference frames are derived based on the theory of vacuum mechanics. If the field is weak and the reference frame is quasi-inertial, these generalized Einstein's equations reduce to Einstein's equations. Thus, this theory may also explain all the experiments which support the theory of general relativity. There exist some differences between this theory and the theory of general relativity.

Background and Objectives: Acute compartment syndrome (ACS) is an emergency condition of the lower limb in which prophylactic fasciotomy is required to prevent complications. A negative pressure wound therapy (NPWT) used to the treatment of fasciotomy wounds provide beneficial clinical results. This study aimed to exchange the authors’ experience of using the NPWT installation system on the lower limb wounds after fasciotomy in ACS. Materials and Methods: This is a retrospective study enrolled consecutive patients with ACS, who underwent fasciotomy and was treated with the NPWT installation system at Department of Vascular Surgery, Provincial Hospital in Kielce from April 2016 to July 2017. Results: The study enrolled 15 patients with a diagnosis of ACS (87% men, mean age 65 years old). An open four-compartment fasciotomy (87%) or two-compartment fasciotomy (13%) was performed. The NPWT was applied on the first day after fasciotomy in 87% of patients. Therapy was initiated by the negative pressure of 125 mm Hg, which maintained at this level until the therapy was finalized. In 80% of patients, the vacuum-assisted wound closure (VAC) dressing changes were performed every 3 days. The first approximation of fasciotomy wounds margins occurred on the 4th day after surgery among 67% of individuals. The average time of using VAC on fasciotomy wounds was 9 days. The average time to definitive closure edges of fasciotomy wounds was 12 days. The average time of hospital stay was 17 days. Conclusions: Our experience indicates the legitimacy of using NPWT in wound treatment after fasciotomy in ACS. The NPWT enables faster primary closure of wounds, reduces edema, as well as decreases hospitalization time.

In quantum gravity perturbation theory in Newton's constant $G$ is known to be badly divergent, and as a result not very useful. Nevertheless, some of the most interesting phenomena in physics are often associated with non-analytic behavior in the coupling constant and the existence of nontrivial quantum condensates. It is therefore possible that pathologies encountered in the case of gravity are more likely the result of inadequate analytical treatment, and not necessarily a reflection of some intrinsic insurmountable problem. The nonperturbative treatment of quantum gravity via the Regge-Wheeler lattice path integral formulation reveals the existence of a new phase involving a nontrivial gravitational vacuum condensate, and a new set of scaling exponents characterizing both the running of $G$ and the long-distance behavior of invariant correlation functions. The appearance of such a gravitational condensate is viewed as analogous to the (equally nonperturbative) gluon and chiral condensates known to describe the physical vacuum of QCD. The resulting quantum theory of gravity is highly constrained, and its physical predictions are found to depend only on one adjustable parameter, a genuinely nonperturbative scale $\xi$ in many ways analogous to the scaling violation parameter $\Lambda_{\bar MS} $ of QCD. Recent results point to significant deviations from classical gravity on distance scales approaching the effective infrared cutoff set by the observed cosmological constant. Such subtle quantum effects are expected to be initially small on current cosmological scales, but could become detectable in future high precision satellite experiments.

This work communicates the connection of measured shadowgraphs from optically induced air breakdown with emission spectroscopy in selected gas mixtures. Laser-induced optical breakdown is generated using 850 mJ and 170 mJ, 6-ns pulses at a wavelength of 1064 nm, the shadowgraphs are recorded using time-delayed 5-ns pulses at a wavelength of 532 nm and a digital camera, and emission spectra are recorded for typically a dozen of discrete time-delays from optical breakdown by employing an intensified charge-coupled device. The symmetry of the breakdown event can be viewed as close-to spherical symmetry for time-delays of several 100 ns. Spectroscopic analysis explores well-above hypersonic expansion dynamics using primarily the diatomic molecule cyanide and atomic hydrogen emission spectroscopy. Analysis of the air breakdown and selected gas breakdown events permits the use of Abel inversion for inference of the expanding species distribution. Typically, species are prevalent at higher density near the hypersonically expanding shockwave, measured by tracing cyanide and a specific carbon atomic line. Overall, recorded air breakdown shadowgraphs are indicative of laser-plasma expansion in selected gas mixtures, and optical spectroscopy delivers analytical insight into plasma expansion phenomena.

Passive plasma spectroscopy is a well-established non-intrusive diagnostic technique. Depending on the emitter and its environment which determine the dominant interactions and effects governing emission line shapes, passive spectroscopy allows the determination of electron densities, emitter and perturber temperatures as well as other quantities like abundances. However, using spectroscopy needs appropriate line shape codes retaining all the physical effects governing the emission line profiles. This requires for line shape code developers to continuously correct or improve them to increase their accuracy when applied for diagnostics. This is exactly the aim expected from code-code and code-data comparisons. In this context, the He I 492 nm emitted in a helium corona discharge at room temperature represents an ideal case since its profile results from several broadening mechanisms: Stark, Doppler, resonance and van der Waals. The importance of each broadening mechanism depends on the plasma parameters. Here the profiles of the He I 492 nm in a helium plasma computed by various codes are compared for a selected set of plasma parameters. In addition, preliminary results related to plasma parameter determination using experimental spectra from a helium corona discharge at low pressure 1- 2 bars, are presented.

Many spectroscopic diagnostics are routinely used as a technique to infer the plasma parameters from line emission spectra but their accuracy depends on the numerical model or code used for the fitting process. However, the validation of a line shape code requires some steps : comparison of the line shape code with other similar codes for some academic (simple) cases and then more complex ones, comparison of the fitting parameters obtained from the best fit of the experimental spectra with those obtained with other diagnostic techniques and/or comparison of the fitting parameters obtained by different codes to fit the same experimental data. Here we compare the profiles of the hydrogen Balmer β line in a helium plasma computed by six codes for a selected set of plasma parameters and we report on the plasma parameters inferred by each of them from the fitting to a number of experimental spectra measured in a helium corona discharge where the pressure was in the range 1- 5 bar.

In this paper, we study the deflection angle for wormhole-like static aether solution by using Gibbons and Werner technique in non-plasma, plasma and dark matter mediums. For this purpose, we use optical spacetime geometry to calculate the Gaussian optical curvature, then implement the Gauss-Bonnet theorem in weak field limits. Moreover, we compute the deflection angle by using a technique known as Keeton and Petters technique. Furthermore, we analyze the graphical behaviour of the bending angle ψ with respect to the impact parameter b, mass m as integration constant and parameter q in non-plasma and plasma mediums. We examine that deflection angle is exponentially increasing as direct with charge. Also, we observe that for small values of b, ψ increases and for large values of b the angle deceases. We also considered an analysis to the shadow cast of the wormhole relative to an observer at various locations. Comparing it the the Schwarzschild shadow, shadow cast is possible for wormhole as r<2m. At r>2m, the Schwarzschild is larger. As r → ∞, we have seen that the behavior of the shadow, as well as the weak deflection angle, approaches that of the Schwarzschild black hole. Overall, the effect of plasma tends to decrease the value of the observables due to the wormhole geometry.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

The interaction of matter when separated by a distance is a fundamental question, whether such interactions occur through instantaneous action at a distance or retarded action at a distance (principle of locality)? While the mainstream consensus favors the principle of locality, instantaneous action at a distance offers certain advantages. Previously, instantaneous action at a distance has been viewed as an appearance or representation from specific gauge choices of electromagnetic potentials (retarded). In this paper, we propose a novel approach that combines Weber’s electrodynamics with the concept of vacuum polarization to explore a new possible connection between the two viewpoints: instantaneous action at a distance and the locality principle. This new approach aligns with the observation of locality in signal/energy propagation while retaining the notion of instantaneous action at a distance.

The Casimir effect can either work over very short distances or at very low temperatures. At the cosmic scale, we naturally deal with long distances, but at the same time, we encounter extraordinarily low temperatures, namely the CMB (Cosmic Microwave Background) tem- perature. Recently, there has been increased interest in the Casimir effect and its implications in cosmology. Here, we briefly demonstrate that the luminosity and radiation pressure of the CMB is mathematical identical to a theoretical Casimir effect within the Hubble sphere, or actually our solution seems to be valid for any Schwarzschild black hole. The Casimir effect forevery Schwarzschild black hole is identical. This also include the Hubble sphere if we treat it as a Schwarzschild black hole that is related to increased interest in black hole cosmology.

Percutaneous kyphoplasty (PKP) is a highly successful treatment option for Kümmell's disease (KD). Due to the obstruction of the fibrocartilaginous membrane at the periphery of the intervertebral vacuum cleft (IVC) and inadequate osteointegration of conventional bone cement, there is insufficient locking strength between trabecular bone and bone cement in Kümmell's disease (KD), leading to postoperative displacement of the bone cement and sub-sequent early surgical failure. However, there is no standard strategy managing this complica-tion at present. We reported a rare case of premature bone cement displacement resulting in adjacent vertebra fracture. An 80-year-old male with Kümmell's disease at T10 received per-cutaneous kyphoplasty (PKP) with bone cement leaking into the upper disc. Only 3 days after the surgery, the patient complained of severe back pain again. X-ray and MRI showed bone cement displacement at T10, adjacent vertebra fracture at T9. In consideration of poor toler-ance of open surgery for the old patient, we successfully revised by using percutaneous ky-phoplasty with multi-point anchoring technique (A-PKP). During a 10-month postoperative follow-up, the patient reported pain relief. X-ray and three-dimensional CT scan revealed no obvious progress of bone cement displacement. Although the exact mechanism underlying this rare complication remains unclear, we observed that the premature bone cement dis-placement can result in adjacent vertebra fracture especially when the pattern of bone cement is blocky. Percutaneous kyphoplasty with multi-point anchoring technique (A-PKP) appears effective in managing this complication.

The optimal regime of three-photon resonant excitation of a helium atom by a femtosecond ul-traviolet (UV) pulse was discovered and numerically studied, at which the maximum power of the third harmonic of the UV field is achieved in the spectrum of dipole acceleration (the second time derivative of the induced dipole moment) of the atom. It is shown that the optimal frequency of the UV field nearly coincides with the frequency of the three-photon transition 1s2 – 1s2p, taking into account its shift as a result of the dynamic Stark effect, and the intensity of the UV field is dictated by the condition of maximizing the product of the populations of the 1s2 and 1s2p states, averaged over the time interval during which the UV field is non-zero. For the considered UV field durations, from 10 to 100 cycles of the carrier frequency (from units to tens of femtoseconds), the optimal intensity lies in the range from 10^14 W/cm^2 to several units of 10^14 W/cm^2. It is shown that with an optimal choice of the frequency and intensity of the UV field, the dynamics of excitation of bound and continuum states, as well as the shape of the time envelope of the dipole acceleration of the atom, weakly depend on the duration of the UV field envelope; only their time scale changes significantly. In addition, under the optimal conditions the average power of the third harmonic signal in the dipole acceleration spectrum is practically independent of the duration of the UV field envelope.

Potential dependent special relativity and Gauss's law for the electric field have been used for gravity by assuming vacuum energy to be generated when the energy is a minimum useful expression for vacuum energy has been found. This expression shows that elementary particles are generated by gravity vacuum filling their hollow balls; using Schrödinger equation for spherically symmetric particles vacuum energy is quantized. Treating mass as vibrating spheres thus solving Schrödinger, coordinate harmonic oscillator energy relation has been found.

We theoretically study the dynamical Casimir effect (DCE), i.e., parametric amplification of a quantum vacuum, in an optomechanical cavity interacting with a photonic crystal, which is considered to be an ideal system to study the microscopic dissipation effect on the DCE. Starting from a total Hamiltonian including the photonic band system as well as the optomechanical cavity, we have derived an effective Floquet-Liouvillian by applying the Floquet method and Brillouin-Wigner-Feshbach projection method. The microscopic dissipation effect is rigorously taken into account in terms of the energy-dependent self-energy. The obtained effective Floquet-Liouvillian exhibits the two competing instabilities, i.e., parametric and resonance instabilities, which determine the stationary mode as a result of the balance between them in the dissipative DCE. Solving the complex eigenvalue problem of the Floquet-Liouvillian, we have determined the stationary mode with vanishing values of the imaginary parts of the eigenvalues. We find a new non-local multimode DCE represented by a multimode Bogoliubov transformation of the cavity mode and the photon band. We show the practical advantage for the observation of DCE in that we can largely reduce the pump frequency when the cavity system is embedded in a narrow band photonic crystal with a bandgap.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

There has been significant increase of studies investigating plasma biomarkers of Alzheimer’s and their relationship to cognitive functioning. The impact of ethnicity on this relationship has not been extensively studied. The current research investigated the relationship between the plasma biomarkers of total tau, Aβ40, Aβ42 and NfL and neuropsychological test performance in a bi-ethnic sample of cognitively unimpaired, older community dwelling adults. The 1326 cognitively unimpaired participants drawn from The Health & Aging Brain Study – Health Disparities (HABS-HD) study included 765 Mexican American participants and 860 non-Hispanic White participants with complete plasma biomarkers and neuropsychological testing. Plasma samples were assayed using Simoa technology. Significant differences in concentrations were found for all of the plasma biomarkers. NHWs had significantly higher levels of each of the biomarkers with a lower Aβ42/ Aβ40. With none of the biomarkers related to performance on any of the neuropsychological tests. For MAs, Aβ40 was the only biomarker that was significantly related to neuropsychological test performance. Aβ40 levels were negatively related to performance on Trails A, Trails B and Digit Symbol Substitution. Results suggest that the relationship of these biomarkers to cognitive functioning is impacted by ethnicity and may be domain specific.

Cenobamate is approved by the European Medicine Agency for the treatment of adult patients with epilepsy (PWEs) who suffer from ongoing focal-onset seizures despite appropriate treatment with at least two established antiseizure medications. Pivotal trials and post-marketing real-world observational studies have suggested a high efficacy with unusually high seizure-free rates. We sought to investigate the serum trough levels of cenobamate under steady-state conditions in seizure-free versus non-responding PWEs, and in PWEs who experienced adverse events versus those who did not. We analyzed samples from 101 PWEs treated with adjunct cenobamate under steady-state conditions. In all, 36 PWEs were seizure-free and 65 were non-responders. In 31 PWEs, adverse events were apparent, whereas in the remaining 70, no tolerability issues were reported. We found a linear correlation between the daily doses (range: 100 mg – 400 mg) and the plasma levels (3.8 mg/l – 54.6 mg/l). Neither the daily doses nor the plasma levels differed significantly between seizure-free and non-responding PWEs or between PWEs with a satisfactory tolerability and those who experienced adverse events. The main reason for this result was that the individual therapeutic ranges varied widely: seizure freedom and adverse effects were observed alongside low doses and plasma levels in some PWEs. Conversely, there were examples of PWEs who did not respond or who reported no tolerability issues at high doses or plasma levels. Still, to evaluate the individual therapeutic range and to better understand the influence of other drugs in cases where concomitant medications are used, the therapeutic drug monitoring of cenobamate may be useful.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

Since late 2019, COVID-19, a severe acute respiratory syndrome pandemic, was caused by the new SARS-CoV-2 virus belonging to the Coronaviridae family, . Several antiviral therapies, mostly derived from previous epidemics, were initially repurposed to fight this not rarely life-threatening respiratory illness. Among them, however, the only specific antibody-based therapy available against SARS-CoV-2 infection during the first year of the pandemic was represented by COVID-19 convalescent plasma (CCP). CCP, collected from recovered individuals, contains high levels of polyclonal antibodies of different subclasses able to neutralize SARS-CoV-2 infection. Tens of randomized controlled trials have been conducted during the last three years of the pandemic to evaluate the safety and the clinical efficacy of CCP in both hospitalized and ambulatory COVID-19 patients, whose main results will be summarized in this narrative review. In addition, we will present the current knowledge on the development of anti-SARS-CoV-2 hyperimmune polyclonal immunoglobulins.

Introduction: The coronary flow reserve (CFR) is a sign of early-stage coronary artery disease (CAD). Plasma atherogenic index (PAI) is related to atherosclerosis and cardiovascular mortality. Therefore, our aim was to determine CFR and PAI in patients with primary hyperparathyroidism (PHPT) and investigate whether PAI can be used in the detection of early-stage CAD. Material and Methods: The sample was comprised of 44 patients with PTHT and 33 healthy volunteers. We defined CFR as the ratio of the hyperemic diastolic peak velocity to the baseline diastolic peak velocity. PAI values were calculated with the formula of log 10 triglyceride (TRG) / high-density lipoprotein (HDL). Result: The comparison of the groups for PAI and CFR demonstrated that PAI levels were significantly higher while CFR levels were significantly lower in the PTHT patients (p<0.01, p=0.01, respectively). The correlation analysis revealed that CFR was negatively correlated with PAI and TRG (PAI- p<0.0001 r=-0.537).The multivariate logistic regression analysis showed that only a high PAI level (OR: 151.6, 95% confidence interval (CI): 4.1-5480, p=0.006) was an independent predictor of reduction in CFR in PHPT patients. Conclusion: Overall, we found an independent correlation between PAI and CFR values. Hence, PAI may be useful in identifying PHPT patients facing a high risk of adverse cardiovascular events and may also allow early diagnosis of subclinical atherosclerosis.

The effect of plasma electrolytic nitrocarburizing on the wear resistance of carbon tool steel in friction couples with hardened steel and lead-tin bronze is considered. The microgeometry of friction tracks and its change with increasing duration of friction tests are analyzed. The equilibrium roughness is determined, which is optimal for the friction couple and ensures minimal wear. The type and mechanism of wear of carbon tool steel after plasma electrolytic nitrocarburizing has been determined. The optimal values of the plasma electrolytic nitrocarburizing parameters, which provide the lowest values of the friction coefficient and weight wear, have been determined. The phase and elemental composition of the surface layer was studied using X-ray diffraction analysis and EDX analysis. The relationship of the microstructure of the nitrocarburized layer of tool steel with the friction coefficient and weight wear is established.

In this paper, we describe the surface modification of Polytetrafluoroethylene (PTFE) through plasma treatment process. Several parameters including different active gases; RF power; dis-tance between the plasma source and sample; and plasma duration were optimized to reduce the hydrophobic nature of PTFE. Three different active gases were used [i.e., N2, O2 and (Ar+H2)], in which N2 was effective to reduce the hydrophobicity of PTFE within shorter plasma duration of 2 minutes. Several surface characterizations including ATR-FTIR, water contact angle, FE-SEM and XPS were utilized to verify the neat and modified PTFE surface after plasma treatment. The plasma treatment using N2 as an active gas improved the wettability of PTFE membrane, show-ing a water contact angle of 108° when compared with the neat PTFE (140°). The SEM images of plasma treated PTFE shows greater modifications on the surface indicating non-uniform fiber alignment and torn fibers at several places. The obtained results confirm the fact that plasma treatment is an effective way to modify the PTFE surface without altering its bulk property.

The employment of PRP in regenerative medicine has not generated the promised grandiose outcomes. Nonetheless, it currently remains the gold standard strategy for tissue regeneration. Therefore, scientific research has focused on identifying other matrices rich in growth factors and cytokines to improve the efficacy of PRP. In the present study, a new technology called AMPLEX PLUS -compound derived from colostrum enriched with exosomes- was applied in combination with PRP to evaluate the concentration trend of 20 bioactive molecules. The results show that the concentration of all the compounds analyzed increased significantly in PRP samples with AMPLEX PLUS technology compared with samples containing only plasma or PRP, suggesting how this new strategy could improve the performance of PRP and make significant advances in regenerative medicine.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

Background: Early diagnosis of acute brain injury (ABI) is critical for patients on venoarterial extracorporeal membrane oxygenation (VA-ECMO) to guide anticoagulation strategy; however, neurological assessment in ECMO is often limited by patient sedation. Methods: In this pilot study of adults from June 2018 to May 2019, plasma samples of glial fibrillary acidic protein (GFAP), neurofilament light chain (NFL), and Tau were collected daily after VA-ECMO cannulation and measured using a multiplex platform. Primary outcomes were the occurrence of ABI, assessed clinically, and neurologic outcome, assessed by modified Rankin Scale (mRS). Results: Of 20 consented patients (median age=48.5 years; 55% female), 8 (40%) had ABI and 15 (75%) had unfavorable neurologic outcomes at discharge. 10 (50%) patients were centrally cannulated. The median duration on ECMO was 4.5 days (IQR: 2.5-9.5). Peak GFAP, NFL, and Tau levels were higher in patients with ABI vs. without (AUC = 0.77; 0.85; 0.57, respectively) and in patients with unfavorable vs. favorable neurologic outcomes (AUC = 0.64; 0.59; 0.73, respectively). GFAP elevated first, NFL elevated to the highest degree, and Tau showed limited change regardless of ABI. Conclusion: Plasma biomarkers may facilitate early detection of ABIs in VA-ECMO where neurological exam is limited and assist timely clinical decision-making.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Polymer adhesives have emerged as a promising dielectric passivation layer in hybrid bonding for 3D integration while they raise misalignment problems during curing. In this work, the synergistic effect of oxygen plasma surface activation and wetting is utilized to achieve bonding between completed cured polyimides. The optimized process achieves a void-less bonding with a maximum shear strength of 35.3 MPa at a low temperature of 250 °C in merely 2 min, significantly shortening the bonding period and decreasing thermal stress. It is found that the plasma activation generated hydrophilic groups on the polyimide surface, and the wetting process further introduced more -OH groups and water molecular on the activated polyimide surface. The synergistic process of plasma activation and wetting facilitate bridging polyimide interfaces to achieve bonding, providing an alternative path for adhesive bonding in 3D integration.

Biostimulation is an animal management practice that helps improve reproductive parameters by modulating animal sensory systems. Chemical signals, mostly known as pheromones, have a great potential in this regard. This study was conducted to determine the influence of short-term female rabbit exposure to different conditions, mainly pheromone-mediated, on reproductive parameters of inseminated does. Groups of 60 females/each were exposed to 1) female urine, 2) male urine, 3) seminal plasma and 4) female-female interaction, just before artificial insemination, and compared to isolated females controls (female-female separated). The following reproductive parameters were analyzed for each group: receptivity (vulvar color), fertility (calving rate), prolificacy and number of born alive and dead kits ⁄ litter. Our results showed that the biostimulation methods employed in this experiment did not significantly improve any of the analyzed parameters. However, female doe exposure to urine, especially to male urine, slightly increased fertility levels when compared to the rest of the experimental conditions. Female-female interaction before artificial insemination, which is a common practice in rabbit farms, did not have any effect, which suggests its removal to avoid unnecessary animal management and time cost. On the other hand, fertility ranges were lower for animals with pale vulvar color whereas no differences were noticed among the other three colours which measure receptivity (pink, red, purple), thus suggesting that these three colours could be grouped together. Additionally, equine chorionic gonadotropin injection could be replaced with various biostimulation methods, therefore reducing or replacing current hormonal treatments, and contributing to animal welfare and to a natural image of animal production.

Plasma and serum are the most widely used blood-derived biofluids for metabolomics and lipidomics assays, but the isolation of these products from blood may introduce additional bias as indicated by the fact that many analytes that are present at high concentrations in blood cells cannot be measured and evaluated in those samples. Of particular concern, variable hemolysis during the pre-processing of blood products could compromise accurate and reproducible quantification. Compared with plasma or serum, whole blood may be a better alternative due to simplicity of processing. In this study, we provide a comprehensive method for quantification of the whole blood sphingolipidome and the concentrations were compared with those from plasma. Combining a single-phase extraction method with liquid-chromatography high resolution mass spectrometry (R=120, 000), assisted by alkaline hydrolysis, we were able to identify and simultaneously quantify more than 150 sphingolipids. Furthermore, most of sphingolipids remained stable after a freeze/thaw cycle. Whole blood contained a higher concentration of most sphingolipids than corresponding plasma. Moreover, individual variations in the levels of sphingolipids were lower for whole blood than plasma. These findings demonstrate that whole blood could be a better alternative to plasma, and potentially guide the evaluation of sphinglipidome for biomarker discovery.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

Steel products have experienced long-standing problems such as unstable product quality and low product homogeneity. In the continuous casting process, realizing constant temperature pouring is an effective way to improve product homogeneity. Plasma heating can compensate for the temperature drop during casting with a tundish and maintain a stable degree of superheating of the molten steel in the tundish. Plasma heating has a certain impact on the cleanliness of the molten steel and on the tundish covering flux in the tundish while compensating for the temperature drop. This paper uses SEM-EDS, XRD and FactSage to analyze the cleanliness of the molten steel and the characteristics of the tundish covering flux before and after heating. The results show that the number density of inclusions in the tundish is significantly lower after heating, improving the floating removal rate of small-sized inclusions; after heating, the surface morphology of the tundish covering flux sample appears transparent and glassy, with uniform morphology; XRD results show that the tundish covering flux after plasma heating exhibits no crystal precipitation and is amorphous and that there is a certain regularity before and after heating; there are no obvious changes in the composition of the tundish covering flux in the liquid phase area.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

In this study, diabetogenic effects of long term Ochratoxin A (OTA) administration in rats were investigated and its role in the etiology of diabetes mellitus (DM) was examined utilizing 42 female Wistar rats for these purposes. The rats were divided into 3 different study and control groups according to the duration of the OTA administration. Rats received 45 μg OTA daily in their feed for 6, 9 and 24 weeks study groups. Three control groups without any treatment were also used in the same periods. Blood and pancreatic tissue samples were collected during the necropsy at the end of 6, 9 and 24 weeks. Plasma values of insulin, glucagon and glucose in study and control groups were determined. Pancreatic lesions were evaluated by histopathological examination; then insulin and glucagon expression in these lesions were determined by immunohistochemical methods. Statistically significant decrease in insulin levels in contrast to increases in glucagon and glucose levels in blood were observed. Slight degeneration in Langerhans islet cells were observed at the histopathological examination in all OTA treated groups. Immunohistochemistry of pancreatic tissue revealed decreased insulin and increased glucagon expression. This study demonstrated that OTA may cause pancreatic damage in Langerhans islet and predispose rats to DM.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

We work within a Winterberg framework where space, i.e., the vacuum, consists of a two component superfluid/super-solid made up of a vast assembly (sea) of positive and negative mass Planck particles, called planckions. These material particles interact indirectly, and have very strong restoring forces keeping them a finite distance apart from each other within their respective species. Because of their mass compensating effect, the vacuum appears massless, charge-less, without pressure, net energy density or entropy. In addition, we consider two variable models, where, , is Newton’s constant, and, , increases with an increase in cosmological time. We argue that there are at least two competing models for the quantum vacuum within such a framework. The first follows a strict extension of Winterberg’s model. This leads to nonsensible results, if increases, going back in cosmological time, as the length scale inherent in such a model will not scale properly. The second model introduces a different length scale, which does scale properly, but keeps the mass of the Planck particle as, the Planck mass. Moreover we establish a connection between ordinary matter, dark matter, and dark energy, where all three mass densities within the Friedman equation must be interpreted as residual vacuum energies, which only surface, once aggregate matter has formed, at relatively low temperatures. The symmetry of the vacuum will be shown to be broken, because of the different scaling laws, beginning with the formation of elementary particles. Much like waves on an ocean where positive and negative planckion mass densities effectively cancel each other out and form a zero vacuum energy density/ zero vacuum pressure surface, these positive mass densities are very small perturbations (anomalies) about the mean. This greatly alleviates, i.e., minimizes the cosmological constant problem, a long standing problem associated with the vacuum.

Alzheimer's disease (AD) is characterized by abnormal amyloid beta (Aβ) plaques and hyperphosphorylated tau in the brain. Aβ plaques precede cognitive impairments and can be detected through amyloid-PET or in cerebrospinal fluid (CSF). Assessing the plasma Aβ42/Aβ40 ratio seems promising for non-invasive and cost-effective detection of brain Aβ accumulation. This approach involves some challenges, including the accuracy of blood-based biomarker measurements and the establishment of clear, standardized thresholds to categorize the risk of developing brain amyloid pathology. Plasma Aβ42/Aβ40 ratio was measured in 277 volunteers without dementia, 70 AD patients and 18 non-AD patients using single-molecule array. Patients (n=88) and some volunteers (n=66) were subject to evaluation of amyloid status by CSF Aβ quantification or PET analysis. Thresholds of plasma Aβ42/Aβ40 ratio were determined based on a Gaussian mixture model, a decision tree, and the Youden index. The 0.0472 threshold, the one with the highest sensitivity, was retained for general population without dementia screening, and the 0.0450 threshold was retained for research and clinical trials recruitment, aiming to minimize the need for CSF or PET analyses to identify amyloid-positive individuals. These findings offer a promising step towards a cost-effective method for identifying individuals at risk of developing AD.

The classical uncertainty principle inequalities were imposed as a mathematical constraint over the general relativity geodesic equation. In this way, the uncertainty principle was reformulated in terms of the proper space-time length element, Planck length and a geodesic-derived scalar, leading to a geometric expression for the uncertainty principle (GeUP). This re-formulation confirmed the necessity for a minimum length for the space-time line element in the geodesic, dependent on a geodesic-derived scalar which made the expression Lorentz-covariant. In agreement with quantum gravity theories, GeUP required the imposition of a perturbation over the background Minkowski metric unrelated to classical gravity. When applied to the Schwarzschild metric, a geodesic exclusion zone was found around the singularity where uncertainty in space-time diverged to infinity.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

We compare several different measures of non-Gaussianity for two families of four-photon superpositions of the Fock states: even vacuum squeezed states and orthogonal-even coherent states.

Currently, conventional spark-ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at different engine speeds and low loads, moving up to the engine lean stable limits. To determine the benefits brought by the proposed strategy, referred to as M100-PAI, the obtained outcomes are compared with the ones obtained using market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ=2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100-PAI, contributed to higher fuel efficiency showing a 10% efficiency gain over the combination E5-gasoline spark ignition.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

The early detection of cognitive decline and timely non-pharmacological management or drug therapy are extremely important in providing care for Parkinson’s disease with dementia (PDD). In this study, we first conducted a discovery study to identify six plasma microRNAs that may allow for the differentiation of PD with or without mild cognitive impairment via NGS. A total of 120 participants were further recruited in a validation cohort and divided into four subgroups, namely, normal controls (HC), PD with no dementia (PDND), PD with mild cognitive impairment (PD-MCI) and PDD. Among the six candidates, miR-203a-3p was successfully detected in the plasma of the validation cohort using droplet digital PCR (ddPCR). Our results show that the ratio of miR-203a-3p/miR-16-5p observed in PDD was significantly increased compared to in PD-MCI (p < 0.001) and PDND (p = 0.041). Moreover, the ratio of miR-203a-3p/miR-16-5p showed a significant correlation with MoCA scores (r = -0.237, p = 0.024) in patients with PD (PwP). The ROC curve of the logistic regression model, consisting of the variables of age, the ratio of miR-203a-3p/miR-16-5p and the UPDRS III score, also demonstrated an average AUC of 0.883 via 5-fold cross-validation. In conclusion, the ratio of miR-203a-3p/miR-16-5p may serve as a potential biomarker for distinguishing cognitive dysfunction from PwP.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Musculoskeletal disorders are increasingly prevalent worldwide, causing significant socioeconomic burdens and diminished quality of life. Notably, patellar chondropathy (PC) is among the most widespread conditions affecting the joint structures, resulting in profound pain and disability. Hyaluronic acid (HA) and platelet-rich plasma (PRP) have emerged as reliable, effective, and minimally invasive alternatives. Continuous research spanning from laboratory settings to clinical applications demonstrate the numerous advantages of both products. These encompass lubrication, anti-inflammation, and stimulation of cellular behaviors linked to proliferation, differentiation, migration, and the release of essential growth factors. Cumulatively, these benefits support the rejuvenation of bone and cartilaginous tissues, which are otherwise compromised due to the prevailing degenerative and inflammatory responses characteristic of tissue damage. While existing literature delves into the physical, mechanical, and biological facets of these products, as well as their commercial variants and distinct clinical uses, there is limited discussion on their interconnected roles. We explore basic science concepts, product variations, and clinical strategies. This comprehensive examination provides physicians with an alternative insight into the pathophysiology of PC as well as biological mechanisms stimulated by both HA and PRP that contribute to tissue restoration.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.