The contactless coalescence of a droplet is of paramount importance for physical and industrial applications. This paper describes a coalescence method in mid-air via acoustic levitation using an ultrasonic phased array system. Acoustic levitation using ultrasonic phased arrays provides promising lab-on-a-drop applications, such as transportation, coalescence, mixing, separation, evaporation, and extraction in a continuous operation. The mechanism of droplet coalescence in mid-air may be better understood by experimentally and numerically exploring the droplet dynamics immediately before the coalescence. In this study, water droplets were experimentally levitated, transported, and coalesced by controlling acoustic fields. We observed that the edge of droplets deformed and attracted each other immediately before the coalescence. Through image processing, the radii of curvature of the droplets were quantified and the pressure difference between the inside and outside the droplet was simulated to obtain the pressure and velocity information on the droplet surface. The results revealed that the sound pressure acting on the droplet clearly decreased before the impact of the droplets. This pressure on the droplets was quantitatively analyzed from the experimental data. Our experimental and numerical results provide deeper physical insights into contactless droplet manipulation for futuristic lab-on-a-drop applications.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

Current, application-driven trends towards larger-scale integration (LSI) of microfluidic systems for comprehensive assay automation and multiplexing pose significant technological and economical challenges to developers. By virtue of their intrinsic capability for powerful sample preparation, centrifugal systems have attracted significant interest in academia and business since the early 1990s. This review models common, rotationally controlled valving schemes at the heart of such “Lab-on-a-Disc” (LoaD) platforms to predict critical spin rates and reliability of flow control mainly based on geometries, location and liquid volumes to be processed, and their experimental tolerances. In absence of larger-scale manufacturing facilities during product development, the method presented here facilitates the provision of efficient simulation tools for virtual prototyping and characterization to greatly expedite design optimization according to key performance metrics. This virtual in silico approach thus significantly accelerates, de-risks and lowers costs along the critical advancement from idea, fluidic testing, bioanalytical validation and scale-up to commercial mass manufacture.

Microfluidics is facing critical challenges in the quest of miniaturizing, integrating, and automating in vitro diagnostics, including the increasing complexity of assays, the gap between the macroscale world and the microscale devices, and the diverse throughput demands in various clinical settings. Here a “3D extensible” microfluidic design paradigm that consists of a set of basic structures and unit operations was developed for constructing any application-specific assay. Four basic structures- check valve (in), check valve (out), double-check valve (in and out), and on-off valve, were designed to mimic basic acts in biochemical assays. By combining these structures linearly, a series of unit operations can be readily formed. We then proposed a “3D extensible” architecture to fulfill the needs of the function integration, the adaptive “world-to-chip” interface, and the adjustable throughput in the X, Y, and Z directions, respectively. To verify this design paradigm, we developed a fully integrated loop-mediated isothermal amplification microsystem that can directly accept swab samples and detect Chlamydia trachomatis automatically with a sensitivity one order higher than that of the conventional kit. This demonstration validated the feasibility of using this paradigm to develop integrated and automated microsystems in a less risky and more consistent manner.

The aim of this study is to provide a detailed strategy for Safe-by-Design (SbD) 3D printed lab-on-a-chip (LOC) device manufacturing, using Fused Filament Fabrication (FFF) technology. At first, the applicability of FFF in lab-on-a-chip device development is briefly discussed. Subsequently, a methodology to categorize, identify and implement SbD measures for FFF is suggested. Furthermore, the most crucial health risks involved in FFF processes are examined, placing the focus on the examination of ultrafine particle (UFP) and Volatile Organic Compound (VOC) emission hazards. Thus, a SbD scheme for lab-on-a-chip manufacturing is provided, while also taking into account process optimization for obtaining satisfactory printed LOC quality. This work can serve as a guideline for the effective application of FFF technology for lab-on-a-chip manufacturing through the safest applicable way, towards a continuous effort to support sustainable development of lab-on-a-chip devices through cost-effective means.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

The lab-on-a-chip concept, enabled by microfluidic technology, promises the integration of multi-ple discrete laboratory techniques into a miniaturised system. Research into microfluidics has generally focused on the development of individual elements of the total system (often with rela-tively limited functionality), without full consideration for integration into a complete fully opti-mised and miniaturised system. Typically, the operation of many of the reported lab-on-a-chip devices is dependent on the support of a laboratory framework. In this paper, a demonstrator platform for routine laboratory analysis is designed and built, which fully integrates a number of technologies into a single device with multiple domains such as fluidics, electronics, pneumatics, hydraulics, and photonics. This facilitates the delivery of breakthroughs in research, by incorpo-rating all physical requirements into a single device. To highlight this proposed approach, this demonstrator microsystem acts as a fully integrated biochemical assay reaction system. The re-sulting design determines enzyme kinetics in an automated process and combines reservoirs, three-dimensional fluidic channels, optical sensing, and electronics in a low-cost, low-power and portable package.

Non-genuine medical products, including diagnostic devices, have become a lucrative business for fraudsters, causing significant damage to revenues and reputation of companies, as well as posing a significant risk to the health of people and societies. Along a “digital twin” representing centrifugal microfluidic flow control on exemplary “Lab-on-a-Disc” (LoaD) systems, a novel, two-pronged strategy to safeguard miniaturized point-of-care devices by means of secret features and manufacturing challenges is outlined; such “hardware encryption” is flexibly programmed for each chip during production, and deciphered from a secure, local or online database at the time of use. This way, unlicensed copying may be efficiently deterred by an unfavourable economy-of-scale, even in absence of legal prosecution.

Understanding cell migration is a key step to unravel many physiological phenomena and predict several pathologies, like cancer metastasis. In particular, mechanical confinement has been proved to be a key factor in the cellular migration strategy choice. As our insight in the field improves, new tools are needed in order to empower biologists’ analysis capabilities. In this framework, microfluidic devices have been used to engineer the mechanical stimuli and to investigate cellular migration response in a more controlled way. In this work, we will review the existing technologies employed in the realization of microfluidic cellular migration assays, namely soft lithography of PDMS and hydrogels and femtosecond laser micromachining. We will give an overview of the state of the art of these devices, focusing on the different geometrical configurations that have been exploited to study specific aspects of cellular migration. Our scope is to highlight the advantages and possibilities given by each approach and to envisage the future developments in in-vitro migration studies under mechanical confinement in microfluidic devices.

Enhancing the degree of functional multiplexing while assuring operational reliability and manufacturability at competitive costs are crucial ingredients for enabling comprehensive sample-to-answer automation, e.g., for use in common, decentralized “Point-of-Care” or “Point-of-Use” scenarios. This paper demonstrates a model-based ‘digital twin’ approach which efficiently supports the algorithmic design optimization of exemplary centrifugo-pneumatic (CP) dissolvable-film (DF) siphon valves towards larger-scale integration (LSI) of well-established “Lab-on-a-Disc” (LoaD) systems. Obviously, the spatial footprint of the valves and their upstream laboratory unit operations (LUOs) have to fit, at a given radial position prescribed by its occurrence in the assay protocol, into the locally accessible disc space. At the same time, the retention rate of a rotationally actuated CP-DF siphon valve and, most challenging, its band width related to unavoidable tolerances of experimental input parameters, need to slot into a defined interval of the practically allowed frequency envelope. To accomplish particular design goals, a set of parametrized metrics is defined, which are to be met within their practical boundaries while (numerically) minimizing the band width in the frequency domain. While each LSI scenario needs to be addressed individually on the basis of the digital twin, a suite of qualitative design rules and instructive showcases structures are presented.

Cutaneous wound healing is a complex multi-stage process involving direct and indirect cell communication events with the aim of efficiently restoring the barrier function of the skin. One key aspect in cutaneous wound healing is associated with cell movement and migration into the physically, chemically and biologically injured area resulting in wound closure. Understanding the conditions under which cell migration is impaired and elucidating the cellular and molecular mechanisms that improve healing dynamics is therefore crucial in devising novel therapeutic strategies to elevate patient suffering, reduce scaring and eliminate chronic wounds. Following the global trend towards automation, miniaturization and integration of cell-based assays into microphysiological systems, conventional wound healing assays such as the scratch assay or cell exclusion assay have recently been translated and improved using microfluidics and lab-on-a-chip technologies. These miniaturized cell analysis systems allow precise spatial and temporal control over a range of dynamic microenvironmental factors including shear stress, biochemical and oxygen gradients to create more reliable in vitro models that resemble the in vivo microenvironment of a wound more closely on a molecular, cellular, and tissue level. The current review provides (a) an overview on the main molecular and cellular processes that take place during wound healing, (b) a brief introduction into conventional in vitro wound healing assays, and (c) a perspective on future cutaneous and vascular wound healing research using microfluidic technology.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

In this paper, a prototype of an automatic lab on PCB for agarose preparation and electrophoresis is developed. The dimensions of the device are 38×34 mm2 and includes a conductivity sensor for detecting the TAE buffer (Tris-Acetate-EDTA buffer), a microheater for mixing, a NTC thermistor for controlling the temperature, a LDR sensor for measuring the transparency of the mixture, and two electrodes for performing the electrophoresis. The agarose preparation functions are governed by a microcontroller. The device requires a PMMA structure to define the wells of the agarose gel, and to release the electrodes from the agarose. The maximum voltage and current that the system requires are 40 V to perform the electrophoresis, and 1 A for activating the microheater. The chosen temperature for mixing is 80ºC, with a mixing time of 10 min. In addition, the curing time is about 30 min. This device is intended to be integrated as a part of a larger lab on PCB system for DNA amplification and detection. However, it can be used to migrate DNA amplified in conventional thermocyclers. Moreover, the device can be modified for preparing larger agarose gels and performing electrophoresis in an automatic manner.

Cancer stem cells remain a challenge to isolate and characterize because of their plastic phenotype. Using a microfluidic lab-on-a-chip based on ultra-high frequency dielectophoresis, we measured the electromagnetic signature of colorectal cancer cells and demonstrated that cancer stem cells show a distinct and lower electromagnetic signature than differentiated cells. The release of extracellular vesicles from tumor cells can drive tumor progression and metastasis development. As extracellular vesicles from cancer stem cells carry more aggressive content, we treated colorectal cancer cells with these vesicles to test whether the lab-on-a-chip can detect a change in phenotype. The electromagnetic signature of treated cells is modified in comparison to untreated cells and sometimes even when no biological change is observed. The lab-on-a-chip provides rapid and relevant result without prior labeling compared to conventional biological approaches. It could be useful in the clinic for early detection of cancer stem cells in the tumor mass and for monitoring the aggressive potential of extracellular vesicles in the bloodstream in order to adapt therapeutic management and prevent relapse.

Alzheimer’s disease (AD) is a significant health concern worldwide with enormous social and economic impact globally. The gradual deterioration of cognitive functions and irreversible neuronal losses are primary features of the disease. Even after decades of research, most therapeutic options are merely symptomatic, and drugs in clinical practice present numerous side effects. Lack of effective diagnostic techniques prevents the early prognosis of disease, resulting in a gradual deterioration in the quality of life. Furthermore, the mechanism of cognitive impairment and AD pathophysiology is poorly understood. Microfluidics exploits different microscale properties of fluids to mimic environments on microfluidic chip-like devices. These miniature multichambered devices can be used to grow cells and 3D tissues in vitro, analyze cell-to-cell communication, decipher the roles of neural cells like microglia, and gain insights into AD pathophysiology. This review focuses on the applications and impact of microfluidics on AD research. We discuss the technical challenges and possible solutions provided by this new cutting-edge technique to understand disease-associated pathways and mechanisms.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

Droplet-based microfluidics has revolutionized numerous fields such as biomedical research, pharmaceuticals, drug discovery, food engineering, flow chemistry, and cosmetics. This paper presents a comprehensive study focusing on the detection and characterization of droplets with volumes in the nanoliter range. Leveraging the precise control of minute liquid volumes, we introduced a novel spectroscopic On-Chip microsensor equipped with integrated microfluidic channels for droplet generation, characterization, and sensing, simultaneously. The microsensor, designed with Interdigitated-Ring-Shaped Electrodes (IRSE) and seamlessly integrated with microfluidic channels, offers enhanced capacitance and impedance signal amplitudes, reproducibility, and reliability in droplet analysis. We were able to make analyses of droplets length in the range 1.0-6.0 mm, velocity 0.66-2.51 mm/s, droplet volume 1.07nL-113.46nL. Experimental results demonstrated that the microsensor's has a great performance in terms of droplet size, velocity, and length, with a significant signal amplitude of capacitance and impedance, and real-time detection capabilities, thereby highlighting its potential for facilitating microcapsule reactions and enabling on-site real-time detection for chemical and biosensor analyses on-chip.

Since its inception in the late 2000s, blockchain has emerged as a powerful tool for creating trust without intermediaries to incentivize global communities for working for a common goal, such as the improvement of its very ecosystem, its applications and community adoption. While first blockchains were mainly devised for confirming transactions of their innate cryptocurrencies like Bitcoin, smart-contract blockchains like Ethereum can interface with the real-world through so-called “oracles”, which feed trustful off-chain information. This paper introduces digital twins of physical objects and processes as computational oracles to effectively unleash the tremendous opportunity offered by blockchain to the realm of fundamental science, research and technology development (RTD). The crowdsourcing concept is illustrated with the example of centrifugal flow control in microfluidic “Lab-on-a-Disc” (LoaD) systems.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Road markings play an important role in road safety because they provide significant information to drivers about the road. For that reason, they must be replaced when they are not correctly perceived by road users. To analyse which are the main factors that affect road marking perception over time, a test section was designed in a two-lane rural highway, running actual traffic over 18 different types of markings fabricated with different combinations of drop-on materials. Chromatic coordinates, luminance and retroreflectivity of each sample were measured during 18 months in order to study their evolution over time. The results obtained show different behaviours depending on the aggregates and application method used. An increment of the durability has been observed with the use of different layers and mixtures of glass microbeads with different sizes.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

Recent improvements within the fields of high-throughput screening and 3D tissue culture have provided the possibility of developing in vitro micro-tissue models that can be used to study diseases and screen potential new therapies. This paper reports a proof of concept study on the use of microvalve-based bioprinting to create laminar MSC-chondrocyte co-cultures as an in vitro model of autologous chondrocyte implantation (ACI), an established cellular therapy for osteoarthritis. Microvalve-based bioprinting uses microvalves to deposit cells suspended in a liquid in a consistent and repeatable manner. In this case MSCs and chondrocytes have been sequentially deposited into an insert based transwell system in order to create a laminar co-culture, with variations in the ratios of the cell types used to investigate the potential for MSCs to stimulate improved repair. Histological and indirect immunofluorescence staining revealed the formation of dense tissue structures within the chondrocyte and MSC-chondrocyte cell co-cultures, alongside the establishment of a proliferative region at the base of the tissue. No stimulatory or inhibitory effect in terms of ECM production was observed through the introduction of MSCs, although the potential for an immunomodulatory benefit remains. This proof-of-concept study therefore provides a novel method to enable the scalable production of therapeutically relevant micro-tissue models that can be used for in vitro research to optimise ACI procedures.

Fluidic larger-scale integration (LSI) resides at the heart of comprehensive sample-to-answer automation and parallelization of assay panels for frequent and ubiquitous bioanalytical testing in decentralized the point-of-use / point-of-care settings. This paper develops a novel “digital twin” strategy with an emphasis on rotational, centrifugo-pneumatic flow control. The underlying model systematically connects retention rates of rotationally actuated valves as a key element of LSI to experimental input parameters; for the first time, the concept of band widths in frequency space as the decisive quantity characterizing operationally robustness is introduced, a set of quantitative performance metrics guiding algorithmic optimization of disc layouts is defined, and the engineering principles of advanced, logical flow control and timing are elucidated. Overall, the digital twin enables efficient design for automating multiplexed bioassay protocols on such “Lab-on-a-Disc” (LoaD) systems featuring high packing density, reliability, configurability, modularity and manufacturability to eventually minimize cost, time and risk of development and production.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

In plants, water flows are the major driving force behind the growth and play a crucial role in the life cycle. To study hydrodynamics, methods based on tracking small particles inside water flows occupy a special place. Due to these tools, it is possible to get information about the dynamics of the spatial distribution of the fluxes characteristics. In this paper, using contrast-enhanced MRI, we have shown that gadolinium chelate, used as an MRI contrast agent, marks the structural characteristics of xylem bundles of maize stem nodes and internodes. Supplementing MRI data, a high-precision visualization of xylem vessels by laser scanning microscopy was used to reveal structural and dimensional characteristics of the stem vascular system. In addition, we proposed the concept of using the prototype "Y-type xylem vascular bundles" as a model of the elementary connection of vessels within the vascular system. A Reynolds number can match the microchannel model with the real xylem vessels.

The illegal use of explosives by terrorists and other criminals is an increasing issue in public spaces, such as airports, railway stations, highways, sports arenas, theaters, and other large buildings. Security in these environments can be achieved by a set of different means, including the installation of scanners and other analytical devices to detect ultra-small traces of explosives in a very short time-frame to be able to take action as early as possible to prevent the detonation of such devices. Unfortunately, an ideal explosive detection system still does not exist, which means that a compromise is needed in practice. Most detection devices lack the extreme analytical sensitivity, which is nevertheless necessary due to the low vapor pressure of nearly all explosives. In addition, the rate of false positives needs to be virtually zero, which is also very difficult to achieve. Here we present an immunosensor system based on kinetic competition, which is known to be very fast and may even overcome affinity limitation, which impairs the performance of many traditional competitive assays. This immunosensor consists of a monolithic glass column with a vast excess of immobilized hapten, which traps the fluorescently labeled antibody as long as no explosive is present. In the case of TNT occurring, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled CMOS camera. Liquid handling is performed with high-precision syringe pumps and chip-based mixing-devices and flow-cells. The system achieved limits of detection of 1 pM (1 ppt) of the fluorescent label and around 100 pM (20 ppt) of the explosive 2,4,6-trinitrotoluene (TNT). The total assay time is less than 8 min. A cross-reactivity test with 5000 pM solutions showed no signal by PETN, RDX, and HMX. This immunosensor belongs to the most sensitive and fastest detectors for TNT with no significant cross-reactivity by non-related compounds.

Analytical chemistry applied to medical and diagnostic analysis, recently focused on the development of cost-effective biosensors able to monitor the health status or to assess the level of specific biomarkers that can be indicative for several diseases. The improvement of technologies relating to the possibility of non-invasive sampling of biological fluids, as well as sensors for the detection of analytical signals and the computational capabilities of the systems routinely employed in everyday life (e.g. smartphones, computers, etc.), make the complete integration of self-standing analytical devices more accessible. This review aims to discuss the biosensors that have been proposed in the last 5 years focusing on two principal detecting approaches, optical and electrochemical, which have been employed for quantifying different kind of target analytes reaching detection limits below the clinical sample levels required. These detection principles applied to Point-of-care (POC) devices, have been extensively reported in literature and even the limited examples found on the market are based on these strategies. This work will show the latest innovations considering the integration of optical and electrochemical detection with the most commonly reported analytical platforms for POC applications such as paper-based or wearable and implantable devices.

Conventional diagnostic techniques are based on utilization of analyte sampling, sensing and signalling on separate platforms for detection purposes, that must be evaded and integrated to a single step procedure in point of care (POC) testing devices. Therefore, the trend has been shifted towards utilization of microfluidic platforms for detection of analytes in biochemical, clinical and food technology due to its being expeditious. Microfluidic systems moulded with polymer substances or glass offer specific and sensitive detection of infectious and non-infectious diseases by providing innumerable benefits including less cost, good biological affinity, strong capillary action and simple process of fabrication. In the case of nucleic acid-based nanosensors, there are some challenges that need to be addressed such as cellular lysis, isolation and amplification of nucleic acid required to be accomplished prior to its detection. To avoid utilization of laborious steps for executing these steps, advances have been deployed in this perspective for on-chip sample preparation, amplification and detection which not only improves sensitivity and selectivity but also saves time and resources. This review emphasizes the significance of microfluidic technology for nucleic acid detection of infectious and non-infectious diseases. The implementation of isothermal amplification in concomitance with lateral flow assay greatly increases the binding efficiency of nanoparticles and biomolecules, improves limit of detection and sensitivity. Most importantly deployment of paper-based material made of cellulose reduces the overall cost. Microfluidic technology in nucleic acid testing has been discussed by explicating its applications in different fields. This review concludes with the prospects and proposes future directions in microfluidic based methods in disease diagnosis.

In this paper, the stability control of the inverted pendulum on a cart with a disturbance forces has been done using observer based and full state feedback H2 controllers. The Lagrangian equation has been used to model the system equation of motions and linearized the system to the unstable upward position. Comparison of the system stability has been simulated by comparing the proposed controllers using Matlab/Scripts and a promising results has been analyzed successfully.

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

The rising of an oil drop in a non-Newtonian viscous solution is studied experimentally. In this case, the shape of the ascending drop is strongly affected by the non-Newtonian properties of the surrounding liquid. We found that the so-called velocity discontinuity phenomena is observed for drops larger than a certain critical size. Beyond the critical velocity, the formation of a long tail is observed, from which small droplets are continuously emitted. We determined that the fragmentation of the tail results mainly from the effect of capillary effects. We explore the idea of using this configuration as a new encapsulation technique, where the size and frequency of droplets can be well predicted.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

Recently, there has been increasing attention toward inhaled nanoparticles (NPs) to develop in-halation therapies for diseases associated with the pulmonary system and investigate the toxic ef-fects of hazardous environmental particles on human lung health. Taking advantage of microfluidic technology for cell culture applications, lung-on-a-chip devices with great potential in replicating the lung air-blood barrier (ABB) have opened new research insights in preclinical pathology and therapeutic studies associated with aerosol NPs. Surprisingly, the air interface in such devices, which makes them tremendously unique among the other common liquid-based cellular mi-crosystems and enables exposure of cultivated cells to the drug/toxic aerosols, has been largely disregarded. Accordingly, there exists a significant research gap in the comprehensive under-standing of the NPs’ dynamics in the lung-on-a-chip devices, which is momentous to control the injection of aerosols to the target area and attain a desired physiochemical efficacy. To address this research gap, a numerical parametric study is presented to provide a deep insight into the dynamic behavior of the airborne NPs in a gas-liquid dual-channel lung-on-a-chip device with a porous membrane separating the channels. A finite element multi-physics model is developed to enable a particle tracing investigation simultaneously in both air and medium phases to replicate the in vivo conditions avoiding laborious and costly experimental trials. The results include the impact of fluid flow as well as geometrical properties on the distribution, deposition, and translocation of the NPs with diameters ranging from 10 nm to 900 nm in the lung-on-a-chip. The obtained results strongly suggest the aerosol injection of NPs instead of the aqueous solution for more efficient deposition on the substrate of the air channel and higher translocation to the media channel. The current study proposes to optimize the affecting parameters to control the injection and delivery of aerosol par-ticles into the lung-on-chip device depending on the objectives of biomedical investigations and provides optimized values for some specific cases. Therefore, this study can assist scientists and researchers in complementing their experimental investigation in future preclinical studies on pulmonary pathology associated with inhaled hazardous and toxic environmental particles, as well as therapeutic studies for developing inhalation drug delivery.

Identifying appropriate animal models is critical in developing translatable in vitro and in vivo systems for therapeutic development and investigating disease pathophysiology. These animal models should have direct biological and translational relevance to the underlying disease they are supposed to mimic. Aging dogs naturally develop a cognitive decline in many aspects including learning and memory, but also exhibit human-like individual variability in the aging process. Neurodegenerative processes that can be observed in both human and canine brains include the progressive accumulation of β-amyloid (Aβ) found as diffuse plaques in the prefrontal cortex, including the gyrus proreus, the hippocampus, and in the cerebral vasculature. A growing body of epidemiological data shows that human patients with neurodegenerative diseases have concurrent intestinal lesions, and histopathological changes in the gastrointestinal (GI) tract occurs decades that evolve before neurodegenerative changes. Gut microbiome alterations also have been observed in many neurodegenerative diseases including Alzheimer’s and Parkinson’s diseases, and inflammatory CNS diseases. Interestingly, only recently has the dog gut microbiome been recognized to more closely resemble in composition and in functional overlap with the human gut microbiome as compared to rodent models. This article aims to review the physiology of the gut-brain axis (GBA), and its involvement with neurodegenerative diseases in dogs and humans. Additionally, we outline the advantages and disadvantages of traditional in vitro and in vivo models and discuss future research directions investigating major human neurodegenerative diseases such as Alzheimer’s and Parkinson’s diseases using dogs.

Organ-on-a-Chip (OoC) systems bring together cell biology, engineering, and material science for creating systems that recapitulate the in vivo microenvironment of tissues and organs. The versatility of OoC systems enables in vitro models for studying physiological processes, drug development, and testing in both academia and industry. This paper evaluates current platforms from the end-user perspective, elaborating on usability, complexity, and robustness. We surveyed 165 peers in over 30 countries and grouped the responses according to preliminary knowledge and the source of the OoC systems that are used. The survey clearly shows that current commercial OoC platforms provide a substantial level of robustness and usability - which is also indicated by an increasing adaptation of the pharmaceutical industry but a lack of complexity can challenge their use as a predictive platform. Self-made systems on the other hand are less robust and standardized but provide the opportunity to develop customized and more complex models which are often needed for human disease modeling. This review serves as a guide for researchers in the OoC field and encourages the development of next-generation OoCs.

Pandemics caused by viruses have threatened lives of thousands of people. Viral infection is a complex and diverse process, and substantial studies have been complemented in understanding the biochemical and molecular interactions between viruses and hosts. However, the physical microenvironment where infections implement is often less carefully considered, and the role of mechanobiology in viral infection remains elusive. Mechanobiology focuses on sensation, transduction and response to intracellular and extracellular physical factors by tissues, cells and extracellular matrix. The intracellular cytoskeleton and mechanosensors have been proved to be extensively involved in virus life cycle. Furthermore, innovative methods in vivo and in vitro are being utilized to elucidate how extracellular factors including stiffness, forces and topography in regulating viral infection. Our current review covers how physical factors from different sources coordinate virus infection. We further discuss how this knowledge can be harnessed in future research on cross-fields of mechanobiology and virology.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

In terms of sustainability, cities become smart when they provide intelligent services to the inhabitants using information and communication technologies without threatening the future of the environment, economy or the society. However, the process of developing such sustainable smart services has certain challenges, especially in understanding the real needs of the people living in the city. Inhabitants of the city or the citizens are the key stakeholders in case of smart services in a city. Active involvement of the people throughout the process is a way to design such services. On the other hand, integrating sustainability, for example including environmental data to the smart city services has been found challenging. Therefore, this research discusses an approach on combining environmental data with regular smart city services and to engage city inhabitants in the process, the approach that is adapted from the concept of living lab methodology. Finally, an application has been developed to represent a smart city service following this method.

Brimonidine, a selective alpha-2 adrenergic agonist, used for treatment of open-angle glaucoma, has been shown to cause neurological side effects such as unresponsiveness, lethargy, hypoventilation, and stupor, mimicking opioid toxicity. We report one case of transient encephalopathy in a toddler, in whom brimonidine accidental toxicity was sus-pected and then confirmed by a toxicology study. The 8-month-old healthy girl child was taken to the pediatric ER since she was drowsy and hypotonic, with miosis. Brain CT scan and toxicological work-up on blood and urine were negative. Starting from hour +4, the child progressively improved, and by hour +6, she recovered to a normal state of consciousness. A survey of available drugs at the child’s reach showed the presence of brimonidine. Thus, ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) was applied to quantify brimonidine in urine and plasma samples, showing 8.40 ng/mL level and 0.79 ng/mL, respectively. To our knowledge, this is the first report for determining brimonidine levels in urine and plasma by UPLC-MS/MS. Insufficient knowledge of the family members about the potential hazards of an apparently innocuous, topical medication such as eye drops may put children at a greater risk of poisoning. Necessary warnings should be better given to parents when prescribing this medication.

The present study evaluates the response to betahistine in patients who presented vestibular drops attacks in the context of Ménière's disease (MD) and the factors that can predict an unfavorable response to it. A total of 43 patients were analyzed, out of which 33 were diagnosed with MD. It is a descriptive, cross-sectional study with retrospective data collection. Data as regards age, accompanying symptoms, etiological diagnosis and response to MD treatment were collected. A statistical analysis was carried out, and we found that the disease evolution time and specific alterations in the vestibulospinal and oculomotor physical examination present an unfavorable response to betahistine, as opposed to the use of intratympanic gentamicin, with which symptomatic control is achieved in 100% of the cases.

Drops are the most important and most common energy dissipator in irrigation networks and erodible canals and consequently, their performance must be well understood. This study was designed to evaluate the capability of Artificial Intelligence (AI) methods including ANN, ANFIS, GRNN, SVM, GP, MLR, and LR to predict the relative energy dissipation (∆E/E0) in vertical drops equipped with a horizontal screen. For this study, 108 experiments were carried out to investigate energy dissipation with variable discharge, varying drop height, and porosity of the horizontal screens. Parameters yc/h, yd/yc, and p are considered as input variables and ∆E/E0 is the output variable. The efficiency of models was compared using Taylor's diagram, Box Plot of the applied error distribution, correlation coefficient (CC), mean absolute error (MAE) and root-mean-square error (RMSE). Results indicate that the performance of the ANFIS_gbellmf based model with CC value of 0.9953, RMSE value of 0.0069 and MAE value of 0.0042 was superior to other applied models. Also, the linear regression model with CC=0.9933, RMSE=0.0083, and MAE= 0.0067performs better than the multiple linear regression model in this study. Results of a sensitivity study suggest that yc/h is the most effective parameter for predicting ∆E/E0.

The investigation of the electromagnetic properties of biological particles in microfluidic platforms may enable wireless monitoring and interaction with functional activity of microorganisms. Of high relevance is the membrane potential as it is one of the most important parameters of living cells. In particular, the complex mechanisms of the cell’s membrane potential are comparable to the dynamics of bacteria membranes, providing a simplified platform for advancing the current techniques and knowledge of general bio-particle dynamics. In this work, we provide a theoretical analysis and experimental results on the microwave detection of bacteria on a microfluidic-based framework for sensing the membrane potential of bacteria. The results enable to further advance the state-of-the-art of electromagnetic bacteria sensing and microfluidic control, and their implication for measuring and interacting with the cell and its membrane potentials, which is of great importance for developing new biotechnological engineered systems and solutions.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

COVID-19 was identified in Wuhan, China in in December 2019, and rapidly spread worldwide, being declared global pandemic one month later on 30 January 2020. Since its emergence, COVID-19 has raised global concerns associated with drastic measures that were never adopted in any previous outbreak, to contain the situation as early as possible. The 2019 novel corona virus (2019-nCoV) or SARS-CoV-2 is the causative agent of COVID-19. 2019-nCoV genetic sequence was rapidly identified within few days since the first reported cases and RT-PCR kits became available for COVID-19 diagnosis. However, RT-PCR diagnosis carries a risk of false-negative results, therefore additional serologic test are needed. The most important approach in the battle against COVID-19 is rapid diagnosis of suspicious cases, timely therapeutic intervention and isolation to avoid community spread. In this review, we summarize the clinical scenario that raises suspicion of COVID-19 and available laboratory diagnostics.

The University of Guayaquil, which shares the same name as the city where it is located, faces the challenge of transforming its image for the XXI century. It was deemed necessary to identify details about the urban evolution of the historic link with the city, in relation to the changes produced by the project’s siting and its direct area of influence. The goal is to integrate the main university campus within a framework which guarantees sustainability and allows innovation in the living lab. To achieve this, the action research method was applied, focused on participation and the logic framework. For the diagnosis, proposal, and management model, integrated working groups were organized with internal users such as professors, students, and university authorities, and external actors such as residents, the local business community, Guayaquil city council, and the Governorate of Guayas. As result of the diagnosis, six different analysis dimensions were established which correspond to the new urban agenda for the future campus: compactness, inclusiveness, resilience, sustainability, safety and participation. As a proposal, the urban design integrates the analysis dimensions whose financing and execution are given by the Town Hall, at the same time the Governorate integrates the campus with its network of community police headquarters.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

Low-resource languages often face the problem of insufficient data, which leads to poor quality in machine translation. One approach to address this issue is data augmentation. Data augmentation involves creating new data by transforming existing data through methods such as flipping, cropping, rotating, and adding noise. Traditionally, pseudo-parallel corpora are generated by randomly replacing words in low-resource language machine translation. However, this method can introduce ambiguity as the same word may have different meanings in different contexts. This study proposes a new approach for low-resource language machine translation, which involves generating pseudo-parallel corpora by replacing phrases. The performance of this approach is compared with other data augmentation methods, and it is observed that combining it with other data augmentation methods further improves performance. To enhance the robustness of the model, R-Drop regularization is also used. R-Drop is an effective method for improving the quality of machine translation. The proposed method was tested on Chinese-Kazakh (Latin script) translation tasks, resulting in performance improvements of 4.99 and 7.7 for Chinese-to-Kazakh and Kazakh-to-Chinese translations, respectively.

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

The ongoing revolution in Deep Learning is redefining the nature of computing that is driven by the increasing amount of pattern classification and cognitive tasks. Specialized digital hardware for deep learning still holds its predominance due to the flexibility offered by the software implementation and maturity of algorithms. However, it is being increasingly desired that cognitive computing occurs at the edge, i.e. on hand-held devices that are energy constrained, which is energy prohibitive when employing digital von Neumann architectures. Recent explorations in digital neuromorphic hardware have shown promise, but offer low neurosynaptic density needed for scaling to applications such as intelligent cognitive assistants (ICA). Large-scale integration of nanoscale emerging memory devices with Complementary Metal Oxide Semiconductor (CMOS) mixed-signal integrated circuits can herald a new generation of Neuromorphic computers that will transcend the von Neumann bottleneck for cognitive computing tasks. Such hybrid Neuromorphic System-on-a-chip (NeuSoC) architectures promise machine learning capability at chip-scale form factor, and several orders of magnitude improvement in energy efficiency. Practical demonstration of such architectures has been limited as performance of emerging memory devices falls short of the expected behavior from the idealized memristor-based analog synapses, or weights, and novel machine learning algorithms are needed to take advantage of the device behavior. In this work, we review the challenges involved and present a pathway to realize ultra-low-power mixed-signal NeuSoC, from device arrays and circuits to spike-based deep learning algorithms, with ‘brain-like’ energy-efficiency.

The traditional practice of harvesting and processing raw date palm sap is not only culturally significant but also an essential nutritional source in South Asia. Yet, the potential for bacterial or viral contamination from animals and environmental sources during its collection remains a real and insufficiently studied risk. Implementing improved food safety measures and collection techniques could mitigate the risk of these infections. Additionally, the adoption of advanced food analytical methods has the potential to identify pathogens and uncover the natural bacterial diversity of these products. The advancement of NGS technologies, particularly nanopore sequencing, offers rapid and highly mobile capabilities. In this study, we employed nanopore sequencing for bacterial metabarcoding of a set of raw date palm sap samples collected without protective coverage against animals in Bangladesh in 2021. We identified several bacterial species with importance in the natural fermentation of the product and demonstrated the feasibility of this NGS method in the surveillance of raw palm sap products. We revealed two fermentation directions dominated by either Leuconostoc species or Lactococcus species in these products at the first 6 hours from harvest along with opportunistic human pathogens in the background, represented with low abundance. Plant pathogens, bacteria with the potential for opportunistic human infections and the sequences of the Exiguobacterium genus were also described and their potential role is discussed.

Ethiopia is one of the countries with the highest level of malnourishment of lactating mothers in sub-Saharan Africa. However, different communities produced different foods solely for lactating mothers. "Shameta" is one of the cereal-based fermented cultural foods exclusively produced for lactating mothers with the perception that it would support the health, strength, and recovery of mothers. This study investigated the effects of fermentation time and blending ratio on the nutritional quality of "Shameta." Three levels of blending ratio of ingredients (Maize-Barley-Fava bean) and three levels of fermentation times were laid down in a completely randomized design (CRD). The study showed that lactic acid bacteria were the dominant group, followed by yeasts. Notably, the ingredient formulation ratio of Maize-Barley-Fava bean (81:5:5) in all fermentation times (8, 10, and 12 days) results in the highest LAB dominance with the highest crude fat (13.23 g/100g) content. However, the highest crude protein (16.56 g/100g) and mineral contents were observed in a ratio mix of 66:10:15 fermented for 12 days. The nutritional quality of culturally prepared Shameta can be improved by optimizing fermentation time and ingredient compositions for better recovery, strength, and health of lactating mothers.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.

Intense physical efforts performed at maximal or near-maximal speeds and the ability to recover among sprint are important characteristics of soccer player. Considering that women's soccer is a markedly growing sport, the aim of the study was to analyse the performance (total time –TT-; fatigue index percentage -IF%) and physiological (aerobic and anaerobic) responses to Repeated Sprint Ability Test (RSA, 7×30 m sprints with 25 s of active recovery among sprints) in an elite female player (age: 30 yrs; BMI: 20.3 kg/m²). A repeated measure MANOVA over the 7 sprints time series was applied (p < 0.05). Results showed that TT was 58.71 s (Ideal Time: 56.98 s) with IF% of 3.0%. Energy contributions were given for 80.3% by aerobic, 19.2% by anaerobic lactid, and 0.5% by anaerobic alactid sources. Considering that 1) we have different kinetics in heart rate (HR) and maximum oxygen uptake with oxygen uptake that reach the peak when HR is still rising, and 2) the energy consumption during intermittent exercises requires different metabolism as a result of physiological stimuli proposed, the present findings substantiate the need to choose specific and adequate training methods for female soccer players that aim at increasing their RSA performances.

We believe that a natural focus of the Physics Education Research community is on understanding and improving student learning in our physics courses. For this purpose, we are introducing smartphones in the physics laboratory. Current smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. In this work, we have considered the magnetic field created by a linear quadrupole and we have studied its dependence on distance. Using an experimental procedure that is simple we have measured the magnetic field using the Hall sensor that most smartphones have, together with the corresponding app. The purpose of this work is to show that the laboratory is a powerful tool that increases significant learning under three conditions: 1) the practice must not be too sophisticated; 2) students must handle objects in the lab; and 3) the practice must be scientifically accurate, including the adjustments by minimum squares, and the following and necessary error calculation.

Let $f\left(1\right)=1$ , and let $f(n+1)=2^{2^{f\left(n\right)}}$ for every positive integer n. We consider the following hypothesis: if a system S ⊆ {x_i · x_j = x_k : i, j, k ∈ {1, . . . , n}} ∪ {x_i + 1 = x_k : i, k ∈{1, . . . , n}} has only finitely many solutions in non-negative integers x₁, . . . , x_n, then each such solution (x₁, . . . , x_n) satisfies x₁, . . . , x_n ≤ f (2n). We prove: (1) the hypothesisimplies that there exists an algorithm which takes as input a Diophantine equation, returns an integer, and this integer is greater than the heights of integer (non-negative integer, positive integer, rational) solutions, if the solution set is finite; (2) the hypothesis implies that there exists an algorithm for listing the Diophantine equations with infinitely many solutions in non-negative integers; (3) the hypothesis implies that the question whether or not a given Diophantine equation has only finitely many rational solutions is decidable by a single query to an oracle that decides whether or not a given Diophantine equation has a rational solution; (4) the hypothesis implies that the question whether or not a given Diophantine equation has only finitely many integer solutions is decidable by a single query to an oracle that decides whether or not a given Diophantine equation has an integer solution; (5) the hypothesis implies that if a set $\mathfrak{M}$ ⊆ has a finite-fold Diophantine representation, then $\mathfrak{M}$ is computable.

This pioneering study presents an in-depth biomechanical examination of soccer's diving header, aiming to quantify its impact on ball speed enhancement (BSE) and effective offensive range (EOR). Despite the diving header's widespread acclaim and historical significance, there remains a dearth of scientific scrutiny into its biomechanical intricacies. Employing an innovative research design featuring a static hanging ball at varied offensive distances and heights, the study replicates diverse header scenarios. The results of 3D motion quantification have shown that a physically excellent player (identified through the maximal standing long jump test) could reach an EOR around 2.64 times his body height. Furthermore, the study unveils that proficient players could attain BSE surpassing 9 m/s, signifying the diving header's heightened efficacy compared to traditional heading techniques, which could only result in 4.5 m/s. Correlation analyses unveil noteworthy relationships, highlighting the pivotal role of head speed at impact and the influence of minimizing speed-drop and temporal disparities for amplified effectiveness. Considerations for optimizing diving header execution are introduced, emphasizing the necessity for targeted training programs. Despite acknowledged limitations inherent to its pilot nature, this exploration furnishes foundational knowledge to guide subsequent research and practical applications, providing valuable insights into soccer training and skill development through a biomechanical lens.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Semiconductor nanowhiskers, in particular, nanostructured whiskers based on zero-dimensional (0D) C70 fullerene, are being actively discussed due to the great potential of their application in modern electronics. For the first time, we proposed and implemented a method for the synthesis of nanostructured C70 fullerene whiskers based on the self-organization of C70 molecules during thermal evaporation of C70 droplets on the substrate surface. We found that the onset of the synthesis of C70 nanowhiskers upon evaporation of drops of a C70 solution in toluene on the substrate surface depends on the substrate temperature. We have provided experimental evidence that an increase in both the C70 concentration in the initial drop and the substrate temperature leads to an increase in the geometric dimensions of C70 nanowhiskers. The obtained results provide useful vision on the role of solute concentration and substrate temperature in the synthesis of one-dimensional materials.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

The effect of coal hydrophilic particles in water-glycerol drops on the maximum diameter of spreading along a hydrophobic solid surface is experimentally studied by analyzing the velocity of internal flows by Particle Image Velocimetry. The grinding fineness of coal particles was 45-80 μm and 120-140 μm, their concentration was 0.06 wt.% and 1 wt.%. The impact of particle-laden drops on a solid surface occurred at Weber numbers (We) from 30 to 120. It is revealed the interrelated influence of We and the concentration of coal particles on changes in the maximum absolute velocity of internal flows in a drop within the kinetic and spreading phases of the drop-wall impact. A physical model is formulated for internal convective flows in the longitudinal section of a drop parallel to the plane of the solid wall. The kinetic energy of translational motion of coal particles in a spreading drop compensates for the energy expended by the drop on sliding friction along the wall. At We=120, the inertia-driven spreading of the particle-laden drop is mainly determined by the dynamics of the deformable Taylor rim. An increase in We contributes to more noticeable differences in the convection velocities in spreading drops. When the drop spreading diameter rises at the maximum velocity of internal flows, a growth of the maximum spreading diameter occurs. The presence of coal particles causes a general tendency to reduce the drop spreading.

The aim of this study is to provide the scientists with a straightforward correlation that can be applied for predicting the Fanning friction factor and consequently the pressure drop during blood flow in small caliber vessels. Due to the small diameter of the conduit, the Reynolds numbers are low and thus the flow is laminar. The study has been conducted using CFD simulations validated with relevant experimental data acquired using an appropriate experimental set-up. The experiments concern pressure drop measurement during the flow of a blood analogue that follows the Casson model, i.e. an aqueous glycerol solution that contains a small amount of xanthan gum and exhibits similar behavior to blood, in a smooth, stainless steel microtube (L=5.6cm and D=400 μm). The interpretation of the resulting numerical data led to the proposal of a simplified model that incorporates the effect of the flow rate, the hematocrit value (35-55%) and the vessel diameter (300-1800 μm) and predicts with better than ±10% the Fanning friction factor and consequently the pressure drop during laminar blood flow in small caliber vessels.

An analysis of the performance of Automatic Dependent Surveillance-Broadcast (ADS-B) data received from the Grand Forks, North Dakota International Airport was carried out in this study. The purpose was to understand the vulnerabilities of Universal Access Transceiver (UAT) ADS-B system and recognize the effects on present and future Air Traffic Control (ATC) operation. The Federal Aviation Administration (FAA) mandated all the General Aviation aircraft to be equipped with ADS-B. The aircraft flying within United States and below the transition altitude (18,000 feet) are more likely to install an UAT ADS-B. At present unmanned aircraft systems (UAS) and autonomous air traffic control (ATC) towers are being integrated into the aviation industry and UAT ADS-B is a basic sensor for both class 1 and class 2 Detect and Avoid (DAA) systems. As a fundamental component of future surveillance system, the anomalies and vulnerabilities of ADS-B system need to be identified to enable a fully utilized airspace with enhanced situational awareness. The data received was archived in GDL-90 format, which was parsed into readable data. The anomaly detection of ADS-B messages was based on the FAA ADS-B performance assessment report. The data investigation revealed ADS-B message suffered from different anomalies including drop out; missing payload; data jump; low confident data and altitude discrepancy. Among those studied, the most severe was drop out and 32.49% of messages suffered from this anomaly. Dropout is an incident where ADS-B failed to update within a specified rate. Considering the potential danger being imposed, an in-depth analysis was carried out to characterize message dropout. Three flight parameters were selected to investigate their effect on drop out. Statistical analysis was carried out and Friedman Statistical Test identified that altitude affected drop out more than any other flight parameters.

This work analyzes the severity and risk associated with Automatic Dependent Surveillance-Broadcast (ADS-B) message drop out in Detect and Avoid (DAA) function of Unmanned Aircraft System (UAS). Performance assessment of the Universal Access Transceiver (UAT) ADS-B message implies that in some cases ADS-B fails to update within a specified update interval, which is referred to as drop out in this work. ADS-B is a fundamental surveillance sensor for both class 1 and class 2 DAA systems. Message loss or drop out has been found as one of the common limitations of the ADS-B system. The key feature of this study is incorporating the update rate of real ADS-B data transmitted from the manned aircraft. The data were received from the Grand Forks International Airport, North Dakota. Monte Carlo method has been adopted to resolve encounter scenarios in the presence of drop out. The change in the alert triggered by the UAS DAA in the presence of ADS-B drop out has been investigated. Furthermore, the risk matrices are created to quantify the associated risk with drop out affected alerts. Simulation results depict that both the duration of drop out and DAA look-ahead time affect the alert-triggering function of UAS. With a small look- ahead window and longer duration of drop out, the number of warning alerts increases. Also, alerts are affected more during an overtaking encounter than that of a head-to-head encounter. A system-level analysis is also carried out to recognize the potential reasons behind the ADS-B drop out.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

This paper presents and discusses the pedagogical implication of teaching Shared Value, presenting a case study about a contamination lab namely the case of the Shared Value Living Lab (SVLL) which took place at the University of Torino (UniTO) in Italy. The paper analyzes the pedagogical side of CSV (arguments, topics, learning methodologies, etc.) in the framework of recent theories and approaches of teaching sustainability in business school and in the cooperation between industry and academia, as well. Our research methodology relies on the analysis and comparison of one case study under an intrinsic as it enables researchers to find “interactivity” and connectedness between the individuals participating. The SVLL case is an interesting example of co-creation of social value between academia and its stakeholders. First, it represents an inclusive project linking society and business; second, SVLL acted as a hub putting in contact different interlocutors; third, SVLL training stimulated the acquisition of soft skill in students (interviews, managing relations, represents the project outside university, explaining the project to people, research curiosity) through contamination activities. With our study, we demonstrate the change in students participating in the SVLL may not only be cognitive but also affective, making students feel hopeful, empowered and liberated, and ready to contribute to a more profound change towards the vast array of pro-sustainability behaviors.

Foot drop is a common disability in post-stroke patients and represents a challenge for the clinician. To date, Ankle Foot Orthosis (AFO) combined with conventional rehabilitation is the gold standard of rehabilitation management. AFO has a palliative mechanical action without actively restoring the associated neural function. Functional Electrical Stimulation (FES), consisting in stimulation of the peroneal nerve pathway, represents an alternative approach. By providing a FES device (Bioness L-300, BIONESS, USA) for 6 months to a post-stroke 22-year-old woman with a foot drop, our goal was to quantify its potential benefit on walking capacity. Gait parameters and the temporal evolution of the speed were collected with a specific connected sole device (Feet Me®) during the 10-meter walking, the Time Up and Go, and the 6-minute walking tests with AFO, FES or without any device (NO). As a result, the walking speed changes on 10-meters were clinically significant with an increase from baseline to 6 months in AFO and FES conditions (+0.14m-1 and +0.36m-1), without any changes in NO condition. In addition, speed decreased at about 4-minutes of the 6-minute walking test in NO and AFO conditions, while speed increased in FES conditions at baseline and after 1, 3 and 6 months. Monitoring gait speed in an endurance test after an ecological rehabilitation training program helps to examine walking performance in post-stroke patients and to propose a specific rehabilitation program depending on a fatigue threshold.

The research presents the inter-comparison of atmospheric variables measured by 9 automatic meteorological stations. This set of data was compared with the measurements of other meteorological stations in order to standardize the values that must be adjusted when taken to different areas. The data of a set of a total of 9 GMX500, which measures conventional meteorological variables, and 10 WS100 sensors, which measures precipitation parameters. The automatic stations were set up at the Huancayo Observatory (Geophysical Institute of Peru) for a period of 5 months. The data set of GMX500 were evaluated comparing with the average of the 9 sensors and the WS100 was compared with a optical disdrometer Parsivel2. The temperature, pressure, relative humidity, wind speed, rainfall rate, and drop size distribution was evaluated. A pair of GMX500 sensors presented high data dispersion, it was found found that the errors came from a bad configuration; once this problem was solved, good agreement was archived, with low RMSE and high correlation. I was found that the WS100 sensors overestimate the precipitation with a percent bias close to 100% and the differences increase with the greater intensity of rain. The DSD retrieved by WS100 have unrealistic behavior with higher concentrations in diameters of 1 mm and 5 mm, in addition to a flattened curve.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

This study investigated the effects of two plyometric training protocols on sprint and change of direction (COD) performance in elite hockey players. A parallel-group randomized controlled trial design was used and seventeen elite male and female field hockey players were randomly allocated into either low-to-high (L-H, n = 8) or high-to-low (H-L, n = 9) training groups. Each group performed separate variations of the drop jump exercise twice weekly for six weeks, with an emphasis on either jump height (L-H) or drop height (H-L). Performance variables assessed included sprint times over 10 m and 20 m, as well as 505 time. A two-way repeated measures analysis of variance was performed and Cohen’s d effect sizes were calculated. The H-L group displayed significant small ES improvement from baseline to post-training in the 10 m sprint (1.893 ± 0.08 s pre vs 1.851 ± 0.06 s post) (ES = −0.44) (P = <0.05). Small but not statistically significant differences between groups were observed for 10 m and 20 m sprint performance, and no significant differences were observed within or between groups for 505 time. These findings highlight the difficulty in substantially enhancing speed and COD ability in highly trained athletic populations through the addition of a low volume, short duration plyometric training protocol.

Impact characterization of linear resonant actuator (LRA) is studied experimentally by newly developed drop tester, which can control various experimental uncertainty such as rotational moment, air resistance, secondary impact and so on. The feasibility of this test apparatus was verified by comparison with free fall test. By utilizing a high-speed camera and measuring the vibrational displacement of spring material, the impact behavior was captured and the damping ratio of the system was defined. Based on the above processes, the finite element model was established and the experimental and analytical results were successfully correlated. Finally, the damage of the system from impact loading can be expected by developed model and as a result, this research can improve the impact reliability of LRA.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Along with the familiar Rossby–Haurwitz waves, two-dimensional flows on the surface of a rotating sphere in the regime of zonostrophic turbulence harbour another class of waves known as zonons. Zonons are wave packets produced by energetic large-scale Rossby–Haurwitz wave modes `enslaving’ other wave modes. They propagate westward with the phase speed of the enslaving modes. Zonons can be visualized as enslaving modes’ `ringing’ in the enslaved ones with the frequencies of the former, the property that renders zonons non-dispersive. Zonons reside in high-shear regions confined between the opposing zonal jets yet they are mainly attached to westward jets and sustained by the ensuing barotropic instability. They exchange energy with the mean flow while preserving their identity in a fully turbulent environment, a feature characteristic of solitary waves. The goal of this study is to deepen our understanding of zonons’ physics using direct numerical simulations, a weakly non-linear theory, and asymptotic analysis, and ascertain that zonons are indeed isomorphic to solitary waves in the Korteweg - de Vries framework. Having this isomorphism established, the analysis is extended to eddies detected in the atmospheres of Jupiter and Saturn based upon the observed mean zonal velocity profiles and earlier findings that circulations on both planets obey the regime of zonostrophic macroturbulence. Not only the analysis confirms that many eddies and eddy trains on both giant planets indeed possess properties of zonons, but the theory also correctly predicts latitudinal bands that confine zonal trajectories of the eddies.

Wobbling motion as an exotic collective mode in nuclei without axial symmetry, was intensively discussed during the last few years. The observation of the newly proposed transverse wobbling, first reported in $^{135}$Pr and soon after in nuclei from other mass regions, was considered as a significant discovery in low-spin nuclear structure. However, both the reported experimental results and the proposed theoretical models were lively questioned in a series of works devoted to the investigation of the low-spin wobbling mode in the same nucleus. The electromagnetic properties of the $\Delta I=1$ transitions connecting the one- to zero-phonon and the two- to one-phonon wobbling bands in $^{135}$Pr were recently remeasured, demonstrating their predominant $M1$ magnetic character which is in contradiction with the wobbling motion interpretation. These new experimental observables being well reproduced by both quasiparticle-plus-triaxial-rotor model and interacting boson-fermion model calculations, are against the previously proposed wobbling characteristics of the low-spin bands in $^{135}$Pr. On the other hand, we obtained conclusive experimental evidence for the theoretically suggested transverse wobbling bands at medium spin in $^{136}$Nd. The comparison of the experimental data with calculations utilizing the triaxial projected shell model and a new developed particle-rotor model with frozen orthogonal geometry of the active nucleons, supports the description in terms of transverse wobbling of medium-spin bands in triaxial even-even nuclei.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

In this study we analyzed the concentration of lipoprotein(a) [Lp(a)], PCSK9-Lp(a) complexes and the circulating monocyte subsets in coronary atherosclerosis. 257 patients with coronary atherosclerosis (CA) and 68 patients without stenotic atherosclerosis in the coronary, carotid and lower extremity arteries (control group) were enrolled. Monocyte subpopulations (classical CD14++CD16-, intermediate CD14++CD16+, non-classical CD14+CD16+) were analyzed by direct immunofluorescence and flow cytometry. Lp(a) and PCSK9-Lp(a) complexes in serum were detected by ELISA. The concentration of Lp(a) was higher in CA group compared to controls (23.0 (9.1;73.3) mg/dL versus 10.7 (4.7;25.0) mg/dL, p&lt;0.05). No correlations between the level of Lp(a) and the concentration of PCSK9-Lp(a) complexes, nor between the level of Lp(a) or PCSK9 and the total number of monocytes were observed in both groups. A slight positive correlation between the concentration of PCSK9-Lp(a) complexes and the absolute level of monocytes was obtained (r=0.20, p=0.002) in patients with atherosclerosis predominantly due to intermediate monocyte subsets (r=0.33, p=0.04). According to regression analysis both PCSK9-Lp(a) complex concentration and BMI were related to the absolute number of blood monocytes in patients with atherosclerosis. Further studies are required to determine the pathogenetic contribution of PCSK9-Lp(a) complexes to the development of atherosclerosis.

The required processes and steps for making bread include technological and innovative concepts. The current trend is the use of less toxic compounds and green processes. Besides lactic acid bacteria and yeast, other microorganisms with special properties, such as enzymes, new aroma and flavor, exopolysaccharides, and vitamins, among other compounds with beneficial properties, could be added to bread manufacture, improving bread quality and health effects for the consumers. Freeze drying, new encapsulation methods, cryoprotectants, spray drying, fluidized bed drying, and vacuum drying are used for probiotics and microorganism cultures that will be used as starters or biological additives in the fermentation. The same development is observed in the preservation methods, and studies with plant extracts and essential oils have been proposed and introduced, replacing chemical agents, such as propionate, within the clean-label bread formulations concept. Baking science is a growing research line incorporating innovative methods and biological additives.

Leptospirosis is a zoonotic disease of global importance. The current killed vaccine provides serovar-specific protection without sterilizing immunity. Several surface antigens, including Leptospira immunoglobulin-like proteins (LigA and LigB), have been identified as subunit vaccine candidates; however, they require potent adjuvants. Bacterial Lipopolysaccharide (LPS), including lipid A, is a well-known immunostimulatory agent, and the formulation of Monophosphoryl Lipid A (MPLA) in Alum is a clinical adjuvant. Being less endotoxic, we tested the adjuvant activity of lipid A purified from L. interrogans serovar Pomona (PLA) for its ability to activate innate and enhance antigen-specific adaptive immune response. PLA-induced activation of macrophages similar to levels induced by MPLA, albeit at a much higher dose, indicating that it is less stimulatory than MPLA. Mice immunized with a Variable portion of LigA (LAV) formulated in Alum and PLA (LAV-Alum-PLA) induced significantly higher levels of LAV-specific humoral and cellular immune response than Alum but similar to levels induced by Alum-MPLA. The adjuvant activity of PLA seems to be quite similar to MPLA and primarily mediated through enhanced recruitment, activation, and uptake of antigens by innate immune cells. Moreover, like MPLA, the PLA formulation was able to generate a long-term memory response. Most importantly, PLA demonstrated better potency than MPLA formulation and generated sterilizing immunity against challenge in a hamster model of leptospirosis. Altogether, our study has provided important insight into the adjuvant activity of Leptospira lipid A and has opened avenues for the development of LPS-based vaccines against this dreadful zoonosis.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

The superficial quality of the strip is a very important issue in steel production; the profile, flat-ness, and geometry of strip are indicators of supreme quality. Considering the dimensions, the thickness is one of the most important variables in the production of strip. In the present study the elastic curve of Back Up Rolls (BUR) is analyzed, considering them as simply supported beams as well as the effect of rolls on the profile of the strip, specifically in the strip edge pro-ducing edge drop. The analysis is simulated with a model in 3D using a Finite Element Method (FEM) considering +0.039mm crown on Back Up Roll and +0.101mm crown on Work Roll (WR). The results showed that there is an instability zone of 76mm in the strip edge, this geometry is symmetrical in both ends of the strip, it was validated with the results of compact X-ray thick-ness gauge from a 4-high cold mill. This study not only provides a theoretical basis for the edge drop, but also provides the basis for the understanding of deformation on rolls used in rolling mill processes and their effect on the thickness, profile, shape, and dimensional quality of strips.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

Under the main features required on portable devices in electrochemical instrumentation is to have a small size, low power consumption, economically affordable, and precision in the measurements. This paper describes the development of a programmable Embedded Potentiostat System (EPS) capable of performing electrochemical sensing over system-on-a-chip platforms. Furthermore, the study explains a circuit design and develops some validation of the entire system. The hardware validation is performed by electrochemical experiments such as Double Step Chronoamperometry (DSC), Linear Sweep Voltammetry (LSV) and Cyclic Voltammetry (CV); moreover, a comparison of the experimental signals between a commercial potentiostat and the EPS was done by analysis of errors on the response signal. Results illustrate that the EPS is capable of handling currents in the range of absolute values of 86.44 to 3000 nA, and having control voltages in the range of ± 2 V. The device can support from 50 to 2000 samples per second. The EPS capabilities were compared with other compact potentiostats. The programmable EPS is an original approach which hugely reduces the hardware complexity and leads the way to create new applications for Point-of-Care or industrial developments with a reusable full electronics module.

We propose a novel moving median estimator specifically designed for online detection of threshold crossings in multi-channel signals, such as extracellular neural recordings. This estimator offers two key advantages: a reduced sensitivity to outliers and the elimination of memory requirements for storing arrival times. Furthermore, its design facilitates parallel implementation on FPGAs, making it ideal for real-time processing of multi-channel recordings.

The objective of the this study was to reduce the benzo[a]pyrene-induced hepatotoxicity method in herbal medicine products and to give proof that neferine, daidzein, genistein possess antihepa-totoxic effects. B[a]P which classified as a group 1 carcinogen and metabolized to B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) causes mutagenic DNA addition products. The reduc-tion of BPDE-DNA adduct formation by B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) was derived by benzo[a]pyrene (B[a]P). In HepG2 cells, B[a]P exhibited toxicity and substance treatment of the cells with B[a]P with neferine in lotus and daidzein, genistein in soybean reduced the BPDE-DNA ad-ducts level. The level of B[a]P-metabolites in the substance treatment of the cells was presented that BPDE levels were reduced by neferine in lotus and daidzein, genisten in soybean. These results suggest that neferine in lotus and daidzein, genistein in soybean prevent B[a]P-induced hepato-toxicity for BPDE-DNA adduct formation.