In the last 10 years, carbon dots (CDs) synthesized from renewable organic resources have been gathered a considerable amount of attention in different fields for their peculiar photoluminescent properties. Moreover, the synthesis of CDs fully responds to the principles of the circular chemistry and the concept of safe-by-design. This review will focus on the different strategies for the incorporation of CDs in organic light-emitting devices (OLEDs) and on the study of the impact of CDs properties on the OLEDs performance. The main current research outcomes and highlights are summarized to guide users towards the fully exploitation of use these materials in optoelectronic applications.

Carbon dots (C-dots) represent an emerging class of non-toxic nano-emitters that show excitation wavelength dependent photoluminescence (PL) with high quantum yield (QY) and minimal photobleaching. The vast majority of studies focus on C-dots that exhibit the strongest PL emission in the blue/green region of the spectrum, while longer wavelength emissions are ideal for applications such as bioimaging, photothermal and photodynamic therapy and light emitting diodes. Effective strategies to modulate the PL emission of C-dot based systems towards the red end of the spectrum rely on extensive conjugation of sp2 domains, heteroatom doping, solvatochromism, surface functionalization and passivation. Those approaches are systematically presented in this review, while emphasis is given on important applications of red-emissive suspensions, nanopowders and polymer nanocomposites.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

Although the vegetative stage of indoor cannabis production can be relatively short in duration, there is a high energy demand due to higher light intensities (LI) than the clonal propagation stage and longer photoperiods than the flowering stage (i.e., 16 – 24 hours vs. 12 hours). While electric lighting is a major component of both energy consumption and overall production costs, there is a lack of scientific information to guide cultivators in selecting a LI that corresponds to their vegetative stage production strategies. To determine the vegetative plant responses to LI, clonal plants of ‘Gelato’ were grown for 21 days with canopy-level photosynthetic photon flux densities (PPFD) ranging between 135 and 1430 µmol·m^-2·s^-1 on a 16-hour photoperiod (i.e., daily light integrals of ≈ 8 to 80 mol·m^-2·d^-1). Plant height and growth index responded quadratically; the number of nodes, stem thickness, and aboveground dry weight increased asymptotically; and internode length and water content of aboveground tissues decreased linearly with increasing LI. Foliar attributes had varying responses to LI. Chlorophyll content index increased asymptotically, leaf size decreased linearly and specific leaf weight increased linearly with increasing LI. Generally, PPFD levels of ≈ 900 µmol·m^-2·s^-1 produced compact, robust plants that are commercially relevant, while PPFD levels of ≈ 600 µmol·m^-2·s^-1 promoted plant morphology with more open architecture – to increase airflow and reduce the potential foliar pests in compact (i.e., indica-dominant) genotypes.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Transferring in vitro-cultured Eustoma seedlings to an ex vitro condition (acclimation) is a big challenge that may expose the seedlings to biotic and abiotic stresses, and affect the internal and external structure of the plants. In addition, in vitro-cultured seedlings of Eustoma are difficult to handle and phenotype and physiological traits such as survival and rosette rate may have altered in the acclimation stage. Therefore, the present study aims to examine the effects of blue, red, and white LED light on the growth and development ex vitro of in vitro-cultured seedlings of Eustoma. The results showed that blue LEDs resulted in greater plant height, internode length, and leaf number, increased upper and lower fresh biomass, and higher chlorophyll content compared with treatment by the other LED lights. Higher stomatal density on the abaxial leaf surface was also observed in the blue LED-treated plants, which also showed a higher survival rate and lower rosette rate. In contrast, the white LED-treated plants had the highest leaf width and internode diameter. Acclimation of the Eustoma plants ex vitro suggests that a combination of blue and white LEDs may be advantageous for better growth and development for large-scale production in a controlled environment.

We overview recent progress in growth aspects of group III-nitride heterostructures for deep ultraviolet (DUV) light-emitting diodes (LEDs), with particular emphasis on the growth approaches for attaining high-quality AlN and high Al-molar fraction AlGaN. The discussion commences with the introduction of the current status of group III-nitride DUV LEDs and the remaining challenges. This segues into discussion of LED designs enabling high device performance followed by the review of advances in the methods for the growth of bulk single crystal AlN intended as a native substrate together with a discussion of its UV transparency. It should be stated, however, that due to the high-cost of bulk AlN substrates at the time of this writing, the growth of DUV LEDs on foreign substrates such as sapphire still dominates the field. On the deposition front, the heteroepitaxial growth approaches incorporate high-temperature metal organic chemical vapor deposition (MOCVD) and pulsed-flow growth, a variant of MOCVD, with the overarching goal of enhancing adatom surface mobility, and thus epitaxial lateral overgrowth which culminates in minimization the effect of lattice- and thermal-mismatches. This is followed by addressing the benefits of pseudomorphic growth of strained high Al-molar fraction AlGaN on AlN. Finally, methods utilized to enhance both p- and n-type conductivity of high Al-molar fraction AlGaN are reviewed.

The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120-W flyback LED drivers was established for conducting theory verification, including theoretic analysis and evaluation of the system design process of the flyback converter. The circuit simulation software SIMPLIS was used to demonstrate the system model, which enabled quick understanding of the system framework established in this study. Regarding LEDs, a commercially available aluminum luminaire was used as the output load. The measured results of the actual circuit and the simulation results were remarkably consistent. For the same system at the same temperature, the error between the simulation and actual results was less than 3%, which proved the reliability of the Taylor series simulation.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Deep-ultraviolet (UV) light-emitting diodes (LEDs) based on AlGaN crystals have low light-emission efficiency; therefore, there is a need to improve this light-emission efficiency for a wide range of applications such as water and air sterilizations. UV-light-transparent device structures are considered one of the many solutions toward increasing light output power. To this end, the present study focused on developing a transparent AlGaN-based tunnel junction (TJ) as the anode of a deep-UV LED. Deep-UV LEDs composed of n+/p+-type AlGaN TJs were fabricated under the growth condition that reduced the carrier compensation in the n+-type AlGaN layers. The operating voltage was 10.8 V under the direct current (DC) operation of 63 A/cm2. In addition, magnesium zinc oxide (MgZnO)/Al reflective electrodes were fabricated to enhance the output power of the AlGaN homoepitaxial TJ LED. The output power was 57.3 mW under a DC operation of 63 A/cm2, and it was 1.7 times higher than that realized using the conventional Ti/Al electrodes. The combination of the AlGaN-based TJ and MgZnO/Al reflective contact allows further improvement of the light output power. This study confirms that the AlGaN TJ is a promising UV-transmittance structure that can obtain a high light-extraction efficiency.

We have experimentally analyzed multi-azimuth degradation mechanisms that govern failures of commercially-available high-power (1 Watt) phosphor-coated white (hppc-W) light-emitting diodes (LEDs) covered with peanut-shaped lens under three current-stress aging (CSA) conditions. Comprehensive analyses focus on photometric, chromatic, electrical, thermal, and packaging characteristics. At the packaging level, (a) the decrease of the phosphor-conversion efficiency, (b) the yellow-browning of the optical lens, and (c) the darkening of the silver-coated reflective layer deposited with extraneous chemical elements (e.g., C, O, Si, Mg, and Cu, respectively) contribute collectively to the integral degradation of the optical power. By contrast, Ohmic contacts, thermal properties, and angles of maximum intensity remain unchanged after 3840 h aging in three cases. Particularly at the chip level, the formation of point defects increases the number of non-radiative recombination centers, and thus decreases the optical power during aging stages. Nevertheless, in view of the change of the ideality factor, the dopant activation and the annealing effect facilitate the increase of the optical power in two specific aging stages (192 h∼384 h and 768 h∼1536 h), respectively. This work offers a systematic guidance for the development of reliable LED-based light sources in general-lighting areas.

Metal halide perovskites have shown excellent optoelectronic properties, including high photoluminescence quantum yield, tunable emission wavelength, narrow full-width at half-maximum and low-cost solution-processed fabrication, which make it exhibit great potential as the emission layer materials of light emitting diodes. With the joint efforts of researchers from different disciplines, there has been a significant progress in the improvement of external quantum efficiency (EQE) and stability of perovskite light emitting diodes (PeLEDs) in recent few years, especially in green PeLEDs with EQE over 30%. In this review, we firstly introduce the basic device structure of PeLEDs, as well as the factors influencing EQE and stability of PeLEDs. Secondly, the development of lead-based and lead-free PeLEDs are summarized systematically. Thirdly, challenges of PeLEDs are discussed in detail, including low EQE of blue PeLEDs, poor device stability and EQE roll-off. Finally, some suggestions and perspectives of the future research directions for PeLEDs are proposed.

The growing awareness of the biological effects of artificial light on humans has stimulated ample research. It is now widely accepted that asynchrony between artificialand natural light-dark cycles can elicit severe detrimental health effects. New research has been devoted to lighting solutions that dynamically change their color to mimic spectral changes of daylight and to account for human needs. However, in some situations, the visual properties of light must be preserved: For example professional TV video editors and shift workers who must work under standardized lighting conditions to do color correction in post-production. We have investigated the possibility to tune circadian effects using white lights that are spectrally different but nonetheless have similar color coordinates thus appear as a similar white tone. Our simulation results indicate that it is possible to modulate circadian light effects by combining LEDs for neutral white (4000 K), a widely used white tone for indoor lighting in europe. The results also show that the solutions combining single-color LEDs do however not meet the quality criteria from the visual point of view because their color rendering ability decays to unacceptable low levels. Combining narrowband LEDs with a broadband white LED improves the color rendering quality and we show how far circadian light effects can be tuned according to common theoretical models. The aim is to reflect daylight situations with artificial lighting, thus having a high melatonin suppression in the morning and low melatonin suppression in the evening. As a consequence our aim is to show what maximum and minimum circadian effect is possible with the same set of LEDs.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

Many quantum dot light-emitting diodes (QLEDs) utilize ZnO nanoparticles (NPs) as an electron injection layer (EIL). However, the use of ZnO NP ETL material often results in charge imbalance within the quantum dot (QD) emitting layer (EML) and exciton quenching at the interface of QD EML and ZnO NP EIL. To overcome these challenges, we introduced an Arginine (Arg) interlayer (IL) onto the ZnO NP EIL. The Arg IL elevated the work function of ZnO NPs, thereby suppressing electron injection into the QD, leading to improved charge balance within the QDs, Additionally, the inherent insulating nature of the Arg IL prevented direct contact between QDs and ZnO NPs, reducing exciton quenching and consequently improving device efficiency. The inverted QLED (IQLED) utilizing a 20-nm-thick Arg IL on ZnO NP EIL exhibited a 2.22-fold increase in current efficiency and a 2.28-fold increase in EQE and compared to an IQLED without an IL. Likewise, the IQLED with a 20-nm-thick Arg IL on ZnO NP EIL demonstrated a 1.34-fold improvement in current efficiency and a 1.36-fold increase in EQE compared to IQLED with a 5-nm-thick PEI IL on ZnO NPs.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Transcranial photobiomodulation (tPBM) has been suggested as a non-invasive neuromodulation tool. Repetitive administration of light-emitting diode (LED)-based tPBM for several weeks significantly improved human cognition. To understand the electrophysiological effects of LED-tPBM on the human brain, we investigated alterations by repeated tPBM in vigilance performance and brain networks using electroencephalography (EEG) in healthy participants. Active and sham LED-based tPBM were administered to the right forehead of young participants twice a week for four weeks. The participants performed a psychomotor vigilance task (PVT) during each tPBM/sham experiment. A 64-electrode EEG system recorded electrophysiological signals from each participant during the first and last visits in the 4-week study. Topographical maps of EEG power enhanced by tPBM were statistically compared for the repeated tPBM effect. A new data-processing framework combining the group singular value decompensation (gSVD) with eLORETA was implemented to identify EEG brain networks. The reaction time of PVT in the tPBM-treated group was significantly improved over four weeks compared to that in the sham group. We observed acute increases in EEG delta and alpha powers during 10-min LED-tPBM while the participants performed the PVT task. We also found that theta, beta, and gamma EEG powers significantly increased globally after four weeks of LED-tPBM. Combining gSVD with eLORETA enabled us to identify EEG brain networks and the corresponding network power changes by repeated 4-week tPBM. This study clearly demonstrated that 4-week prefrontal LED-tPBM can neuromodulate several key EEG networks, implying a possible causal effect between modulated brain networks and improved psychomotor vigilance outcomes.

This paper presents a study aimed at enhancing the performance of quantum dot light-emitting didoes (QLEDs) by employing a solution-processed molybdenum oxide (MoO3) nanoparticle (NP) as a hole injection layer (HIL). The study investigates the impact of varying the concentrations of the MoO3 NP layer on device characteristics and explores the underlying mechanisms responsible for the observed enhancements. Experimental techniques such as an X-ray diffraction and field-emission transmission electron microscopy were employed to confirm the formation of MoO3 NPs during the synthesis process. Ultraviolet photoelectron spectroscopy is employed to analyze the electron structure of the QLEDs. The QLED with an 8 mg/mL concentration of MoO3 nanoparticles achieves remarkable improvements in device performance, with a maximum luminance of 69,240.7 cd/cm2, maximum current efficiency of 56.0 cd/A, and maximum external quantum efficiency (EQE) of 13.2%. The obtained results signify a notable progress in comparison to QLED without HIL and those utilizing the widely used poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) HIL. They exhibit a remarkable enhancement of 59.5% and 26.4% in maximum current efficiency, respectively, as well as a significant improvement of 42.7% and 20.0% in maximum EQE, respectively. This study opens up new possibilities for the selection of HIL and the fabrication of solution-processed QLEDs, contributing to the potential commercialization of these devices in the future.

Zn_0.9Mg_0.1O nanoparticle (NP) were employed as electron transport layers (ETLs) with varying thicknesses to investigate their influence on the efficiency of the top-emission quantum dot light-emitting diodes (TE-QLEDs) fabricated inside the bank. An increase in the thickness of the Zn_0.9Mg_0.1O NP ETL led to a decrease in the concentration of oxygen vacancies, reducing the conductivity of the Zn_0.9Mg_0.1O and resulting in lower current density in the TE-QLEDs. The decrease in conductivity of Zn_0.9Mg_0.1O NP ETL was confirmed through electron-only device (EOD) characterization. Furthermore, it was noted that when the thickness of Zn_0.9Mg_0.1O NP ETL was 30 nm, the concentration of hydroxyl species reached its minimum. By minimizing the presence of hydroxyl species, exciton quenching at the quantum dot (QD) and Zn_0.9Mg_0.1O NP ETL interface was minimized, enhancing charge balance within the QD, significantly improving the efficiency of QLED. We successfully demonstrated that TE-QLED with a 30 nm-thick Zn_0.9Mg_0.1O NP ETL exhibits outstanding performance, achieving a maximum current efficiency of 91.92 cd/A and a maximum external quantum efficiency of 21.66%. These results suggest that Zn_0.9Mg_0.1O NP ETL, when tailored to an appropriate thickness, can serve as an ETL for TE-QLEDs, effectively suppressing exciton quenching and enhancing the charge balance in the TE-QLEDs.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

Dendrobium okinawense is an endangered epiphytic orchid, and there has been no scientific report so far on its propagation. Protocorm is mass of cell, and protocorm-like bodies (PLBs) look alike protocorm produced by vegetative explants in vitro. Regeneration of PLBs is the most efficient technique for the orchids micro-propagation. We used different light emitting diodes (LEDs) for the efficient PLB organogenesis of D. okinawense. PLBs regenartion under green and red LED surpassed respectively 81.1% and 71.6% in numbers, and respectively 80.8% and 57.8% in fresh weight over white fluorescent light. We manipulated the culture media by different concentrations of PCIB and HMI. PLBs organogenesis promoted by low concentration, it increased respectively 35.9% and 19.3% over control by 0.01 mg/L PCIB and 0.01 ml/L HMI in numbers. Green LED and PCIB independently produced mostly similar numbers of new PLBs. Interestingly, culture media with 0.01 mg/L of PCIB further increased 8.5% of the numbers of PLBs under green LED, whereas the culture media with 0.01 mg/L HMI reduced the number of PLBs under green LED. PLBs culture under green LED with very low concentrations of PCIB manipulated culture media can significantly increase their organogenesis of D. okinawense.

Organic light-emitting diodes (OLEDs) have garnered considerable attention in academic and industrial circles due to their potential applications in flat panel displays and solid-state lighting technologies, leveraging the advantages offered by organic electroactive derivatives over their inorganic counterparts. The thin and flexible design of OLEDs enables the development of innovative lighting solutions, facilitating the creation of customizable and contoured lighting panels. Among the diverse electroactive components employed in the molecular design of OLED materials, the benzophenone core has attracted much attention as fragment for synthesis of organic semiconductors. On the other hand, the benzophenone also functions as a classical phosphor with high intersystem crossing efficiency. This characteristic makes it as compelling candidate for effective reverse intersystem crossing, potentially leading to the development of thermally activated delayed fluorescent (TADF) emitters. These emitting materials witnessed a pronounced interest in recent years due to their incorporation in metal-free electroactive frameworks and the capability to convert triplet excitons into emissive singlet excitons through reverse intersystem crossing (RISC), consequently achieving exceptionally high external quantum efficiencies (EQEs). This review article comprehensively overviews the synthetic pathways, thermal characteristics, electrochemical behaviour and photo-physical properties of the derivatives based on benzophenone. Furthermore, we explore their applications in OLED devices, both as host materials and emitters, shedding light on the promising opportunities that benzophenone-based compounds present in advancing OLED technology.

A series of D–π–A diketopyrrolopyrrole (DPP)-based small molecules have been designed for organic light-emitting diodes (OLEDs) and organic solar cells (OSCs) applications. Appling the PBE0/6-31G(d,p) method, the ground state geometry and relevant electronic properties were investigated. The first excited singlet state geometry and the absorption and fluorescent spectra were simulated at the TD-PBE0/6-31G(d,p) level. The calculated results reveal that the photophysical properties are affected through the introduction of different end groups. Furthermore, the electronic transitions corresponding to absorption and emission exhibit intramolecular charge transfer feature. It was disclosed that the designed molecules act not only as luminescent for OLEDs, but also donor materials in OSCs. Moreover, they also can be used as potential electron transfer materials using for OLEDs and OSCs.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

Organic light-emitting diodes (OLEDs) have ushered in a technological revolution with their remarkable impact on diverse sectors of our daily lives. These versatile devices known for their outstanding display and lighting capabilities, have become indispensable components in various industries including smartphones, tablets, televisions, and automotive applications. This paper delves into the development of a group of twisted donor-acceptor-donor (D-A-D) derivatives incorporating bicarbazole and benzophenone structures for potential use as blue emitters in OLEDs. The synthesized compounds, namely DB14, DB23 and DB29, were designed with various alkyl side chains to enhance their film forming properties as for blue emitters. Characterization and evaluation of these derivatives included photophysical, electrochemical, thermal, and electroluminescent analysis. Some of the OLED devices incorporating these emitters demonstrated promising performance with maximum current efficiency (CEmax) of 2.6 cd/A and external quantum efficiency (EQEmax) of 5.3%. Notably, the DB23 emitter exhibited the highest EQE among all devices. The study also emphasizes the influence of host-guest energy transfer, optimal doping concentrations, and molecular structures on device performance. This research not only contributes to the understanding of advanced OLED materials but also provides insights into designing efficient blue emitters for future display and lighting applications, thereby advancing the field of organic electronics.

Organic light-emitting diodes (OLEDs) are energy-efficient; however, the coordinating ligand can affect their stability. Sky-blue phosphorescent Pt(II) complexes with a C^N chelate, fluorinated-dbi (dbi = [1-(2,4-diisopropyldibenzo[b,d]furan-3-yl)-2-phenyl-1H-imidazole]), and acetylactonate (acac)(1)/picolinate (pic)(2) ancillary ligands were synthesized. The molecular structures were characterized using various spectroscopic methods. The Pt(II) coordination sphere in 2 exhibited a distorted square-planar geometry, with several intra- and inter-molecular interactions involving Cπ⋯H/Cπ⋯Cπ stacking. Complex 1 emitted bright sky-blue light (λmax = 485 nm) with a moderate photoluminescent quantum efficiency of 0.37 and short decay time (6.1 µs) compared to those of 2. Time-dependent density functional theory calculations suggested that the electronic transition of 1 arose from ligand(C^N)-centered π–π* transitions combined with metal-to-ligand charge transfer transitions (MLCT), whereas that of 2 arose from MLCT and ligand(C^N)-to-ligand(pic) charge transfer (LLCT), with minimal contribution from the C^N chelate to the lowest unoccupied molecular orbital. Multi-layered phosphorescent OLEDs using 1 as a dopant and a mixed host, 3,3-di(9H-carbazol-9-yl)-1,1-biphenyl:3-di(9H-carbazol-9-yl)-1,1-biphenyl (mCBP)/9-(3’-carbazol-9-yl-5-cyano-biphenyl-3-yl)-9H-carbazole-3-carbonitrile (CNmCBPCN) were successfully fabricated. At a 10% doping of 1, a current efficiency of 13.6 cd A−1 and external quantum efficiency of 8.4 % at 100 cd m−2 were achieved. These results show that the ancillary ligand in phosphorescent Pt(II) complexes must be considered.

This work presents the results of the experimental and theoretical study of the static pull-in of tilting actuation executed by a hybrid levitation micro-actuator (HLMA) based on the combination of inductive levitation and electrostatic actuation. A semi-analytical model to study such the pull-in phenomenon is developed, for the first time, as a result of using the qualitative technique based on the Lagrangian approach to analyze inductive contactless suspensions presented in work and a recent progress in the calculation of mutual inductance and force between two circular filaments. The obtained non-linear model, accounting for two degrees of freedom of the actuator, allows us to predict accurately the static pull-in displacement and voltage. The results of modelling were verified experimentally and agree well with measurements.

While laminar flow heat transfer and mixing in microfluidic geometries has been investigated experimentally, as has the effect of geometry-induced turbulence in microfluidic flow (it is well documented that turbulence increases convective heat transfer in macrofluidic flow), little literature exists investigating the effect of electrokinetically-induced turbulence on heat transfer at the micro scale. Using recently observed experimental data, this work employed computational fluid dynamics coupled with electromagnetic simulations to determine if electrokinetically-forced, low-Reynolds number turbulence could be observed in a rectangular microchannel with using Newtonian fluids. Analysis of the results was done via comparison to the experimental criteria defined for turbulent flow. This work shows that, even with a simplified simulation setup, computational fluid dynamics (CFD) software can produce results comparable to experimental observations of low-Reynolds turbulence in microchannels using Newtonian fluids. In addition to comparing simulated velocities and turbulent energies to experimental data this work also presents initial data on the effects of electrokinetic forcing on microfluidic flow based on entropy generation rates.

The protection of first responders from radioactive contamination of alpha emitters that may result from a radiological accident is of great complexity due to the short range of the alpha particle in air of a few cm. To overcome this issue, for the first time a system for near real-time measuring alpha particles remotely mounted on a UAS has been developed, tested and calibrated. The new system, based on an optical system adapted to be installed on the UAS in order to measure the UV-C fluorescent emitting by the alpha particle in air, has been tested and calibrated carried out by laboratory and in field experiments using UV-C leds and ²⁴¹Am sources. In experimental flights, the probability of detecting a point source was determined to be approximately 60%. In case of a surface extended source, a detection efficiency per unit surface activity of ten counts per second per MBq cm^-2 are calculated. A background count rate of UV-C around 26 ± 28 s^-1 for an integration time of 0.1 s was measured during flights, which leads to a decision threshold surface activity of 5 MBq cm^-2.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

Micro-technology has played a substantial role in bioscience, biomedical and biotechnological research due to its core advantages in modern science and engineering. It has created unique development in various sectors of bio-research and upsurges the efficacy of research at the molecular level in recent years. Microfluidic technology makes it possible to manipulate sample volumes at the micro- and nano-level (called nanofluidics) with terrific control outside in vivo cellular microenvironment, enabling the reduction of discrepancies between in vivo and in vitro environments as well as reducing reaction time and cost. In this review, we discuss various effective integrations of microfluidic technologies into biotechnology and its paradigmatic significance in bio-research, supporting mechanical and chemical in vitro cellular micro-environment. Specific innovations relating to the application of microfluidics to advance microbial life, solitary and co-cultures along with a multiple-type cell culturing, cellular communications, cellular interactions and population dynamics are discussed.

When lighting photographic scenes, light sources are often coupled with light-shaping attachments to alter the original light. While the colour rendering properties of the light sources are known, the effect of the added modifiers has not yet been fully investigated. In this research, the effects of light-shaping attachments such as snoot, beauty dish and a range of softboxes on the colour rendering index of the original light sources are investigated using a series of spectrophotometric measurements. The results outline the effects of each light-shaping attachment and provide guidance on the usability of the modifiers used when it comes to accurate colour rendering.

As the problem of light pollution becomes more serious, more and more scholars pay attention to this issue and carry out related research. In the perspective of cities, the measurements of light pollution mainly focus on the brightness of the sky or artificial lighting on the ground. However, there is lack of research on the whole urban space. With the two-dimensional brightness analyses, this paper processes the changes of the light environment of the whole urban space into image quantization. It gets the 3D and 2D light environment changes of luminance distribution, color temperature distribution and chromaticity in the three space layers, the ground layer, the urban canopy layer and the sky layer, from dusk with natural light to night with artificial lighting completely. It is found that the brightness difference between the light environments among the three city levels gradually reduces with the measuring time, and the final values maintain at 0.11~0.25 cd/m². In the ground layer, the light environment is mainly affected by the lighting facilities, and vegetation can prevent the light from scattering up. The light environment of the urban canopy layer is the brightest in the whole city space and has the largest influence on the sky layer. The color concentrates in the range of yellow and red. The color temperature near the ground distributes in 3000K~15000K, and near the sky distributes in 2300K~2700K which is warmer than the natural night sky. The sky brightness of Dalian city is about 951 times than the natural night sky.

The controllability and consistency in the fabrication of micro-textures on large-scale remains a challenge for existing production processes. Mask electrolyte jet machining (MEJM) is an alternative to Jet-ECM for controllable and high-throughput surface microfabrication with more consistency of dimensional tolerances. This hybrid configuration combines the high-throughput of masked-ECM and the adjustable flow-field of jet-ECM. In this work, a duckbill jet nozzle was introduced to make MEJM more capable of batch micro-structuring. A multiphysics model was built to simulate the distribution of electrochemical reaction ions, the cur- rent density distribution and the evolution of the shape of the machined cavity. Experimental investigations are presented showing the influence of the machining voltage and nozzle moving speed on the micro cavity. Several 35 ×35 micro cavity arrays with a diameter of 24.92 − 11.73 µm and depth of 15.86 − 7.24 µm are generated on 304 stainless steel.

We report a 92 channel RF channelizer based on a 48.9 GHz integrated micro-comb that operates via soliton crystals, together with a passive high-Q ring resonator that acts as a periodic filter with an optical 3dB bandwidth of 121.4 MHz. We obtain an instant RF bandwidth of 8.08 GHz and 17.55 GHz achieved through temperature tuning. These results represent a major advance to achieving fully integrated photonic RF spectrum channelizers with reduced low complexity, size, and high performance for digital-compatible signal detection and broadband analog signal processing.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

The study of emission, propagation, and reflection of balls in Newtonian mechanics, employing the laws of conservation of momentum and energy when the mass of balls converges to zero, concludes that the kinematics of light is like that of massless balls. The kinematics of light explains why light speed is the constant in each inertial frame in which the light source and reflective mirror are at rest, why the laws of physics have the same form in each inertial frame, and why any experiment in an inertial frame cannot prove the motion of that the other inertial frame. The theory of special relativity misapplies symmetry observed in phenomena to two inertial frames; therefore, it duplicates a physics phenomenon from one inertial frame, considered stationary, into another. Moreover, Lorentz’s transformation offers light speed at the constant in the moving and opposite direction of the inertial frame but is variable in any other direction. Therefore, the theory of special relativity rejects itself with these unacceptable conclusions.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

This paper describes the use of a new obtrusive light module of the Illumina v2 model to estimate the light that may enter bedroom windows. We used as input to the model, 1- the sources’ flux and spectrum derived from the color images taken by astronauts from the international space station, 2- an association between source spectrum and angular emission, and 3- a per zone inventory of obstacles properties and lamp height. The model calculate the spectral irradiance incident to buildings’ windows taking into account for the orientation of the street. By using the color information from an ISS image, we can classify pixels as a function of their spectra. With the same image, it is also possible to determine the upward photopic radiance for each pixel. Both serve as inputs to the model to calculate the spectral irradiance on any window. By having the spectral irradiance, it is possible to determine the Melatonin Suppression Index and the photopic irradiance on the window. Such information can later be used to perform epidemiological studies. The new methodology is applied to the case of Montréal in Canada for a set of houses’ locations. The computations are made for 2013 (pre-LED era).

The use of several light-related variables, such as the Secchi disc depth, the euphotic depth, and in particular, the diffuse attenuation coefficient (Kd), is deeply rooted in phytoplankton research, but these are not the most appropriate indicators of the amount of light available for photosynthesis. We argue that the variable of interest for phytoplankton is the mean light intensity in the mixed layer (Im), which represents the mean light to which phytoplankton cells are exposed throughout their life cycle, while being continuously mixed in the mixed layer. We use empirical data collected in different coastal ecosystems in southern Portugal to demonstrate why Im should be the preferred metric instead of the deeply rooted Kd. We show that, although the relationship between Im and Kd is inversely proportional, it is not always strong or even significant. Different Im values can be associated to the same Kd, but distinct Im have different physiological effects of phytoplankton. Therefore, Kd does not capture the amount of light available for photosynthesis, given that, unlike Im, Kd calculation does not consider the depth of the mixed layer. Therefore, we urge phytoplankton researchers to consider the measurement and calculation of Im when evaluating light-related processes in phytoplankton ecology.

To improve the measurement accuracy of wood density and study the linear correlation between the drill feed resistance and wood density, a new micro drill instrument that can can simultaneously measure the rotation resistance and feed resistance of the drill needle was designed. The test wood samples included hardwood, softwood and conifer. The absolute dry density of each wood sample was measured. The drill resistance data was tested by using self-developed micro drill instrument and Resistogaph 650-SC. 4 linear models between drill resistance and the absolute dry density of wood . The results showed that: the statistical indicators of each model of the self-made micro drill resistance in-strument were better than the corresponding indicators of Resistogaph 650-SC; the coefficient of determination of the linear regression model between the feed resistance of the self-made micro drill resistance instrument and the absolute dry density of wood was 0.946; the statistical indicators of model including rotation resistance and feed resistance, were better than those of the model only including rotation resistance. Therefor, the design proposed in the article is reasonable, and increasing the feed resistance can improve the measurement accuracy of the micro drill resistance instrument for measuring wood density.

The current study investigated the impacts of light quality and different levels of fertility on mineral nutrient concentrations in shoot and root tissues of Chinese kale (Brassica oleracea var. alboglabra). ‘Green Lance’ Chinese kale were grown under: 1) fluorescent/incandescent light; 2) 10% blue (447 ± 5 nm) / 90% red (627 ± 5 nm) LED light; 3) 20% blue / 80% red LED light; and 4) 40% blue / 60% red LED light as sole-source lighting at two different levels of fertility. All plants were harvested 30 d after seeding, and shoot and root tissues were analyzed for mineral nutrients. Lighting and fertility interacted to influence kale shoot and root mineral nutrient concentrations. Results indicate sole-source LED lighting used in production can impact mineral nutritional values of baby leafy greens now popular for the packaged market.

Emission, propagation, and reflection of light as mechanical phenomena in inertial frames are based on the behavior of balls at the limit when their mass is zero. The kinematics of massless balls is like that of balls with mass. Light as a wave or particle is a massless entity. Therefore, it is natural to apply the kinematics of the massless balls to light. Consequently, the kinematics of light depends on its kinetics of electromagnetic nature and its kinematics of mechanical nature in its interactions of emission and reflection with the matter. The study of the physics phenomena in the frame at absolute rest includes those in the inertial frames. Considering this and applying the emission, propagation, and reflection of light as mechanical phenomena in the vacuum of the frame at absolute rest, this study derives formulas for the speed of the wavefront of a ray of light reflected by a fixed and moving mirror when the light comes from a fixed and moving source. The derived formulas apply to the modified Michelson interferometer, employed independently by R. Tomaschek and D. C. Miller in their experiments.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm x 0.95 mm x 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). The medical grade silicone elastomer MED-4244 (NuSil Technology LLC, Radnor, PA, USA) was used. Molds for µIM were 3D printed from a commercially available resin PlasGRAY V2 (Asiga, Alexandria, Australia, TG = 84 °C) via a high-resolution DLP process (xy-resolution of 32 µm, z-resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bio-efficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. Wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over a time of 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over a time of 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

Ocular light exposure has important influences on human health and well-being through modulation of circadian rhythms and sleep, as well as neuroendocrine and cognitive functions. Current patterns of light exposure do not optimally engage these actions for many individuals, but advances in our understanding of the underpinning mechanisms and emerging lighting technologies now present opportunities to adjust lighting to promote optimal physical and mental health and performance. A newly developed, SI-compliant standard provides a way of quantifying the influence of light on the intrinsically photosensitive, melanopsin-expressing, retinal neurons that mediate these effects. The present report provides recommendations for lighting, based on an expert-scientific consensus and expressed according to this new measurement standard. These recommendations are supported by a comprehensive analysis of the sensitivity of human ‘non-visual’ responses to ocular light, are centred on an easily measured quantity (melanopic equivalent daylight (D65) illuminance), and provide a straightforward framework to inform lighting design and practice.

In this work, an energy-saving smart light controlling system has been proposed that can main-tain the desired intensity of light in a room automatically. Unlike the conventional light control system, the proposed system splits a large room into several zones and analyzes the light inten-sity of each zone; hence, the controlling unit adjusts the light intensity to the desired level. The main controlling unit consists of a light sensor, a motion sensor, a relay with a driver unit, an LCD display, etc. for controlling light efficiently to reduce the power waste. The sensors meas-ure the intensity of light, based on the standard light intensity data chart the controller units make a decision how many light bulbs are needed to be switched ON/OFF in a particular zone. Moreover, the system automatically switched-OFF all light bulbs when there is nobody in the room. Proteus design suite 8.0 is used to design and simulation of the proposed system. Moreo-ver, the PCB layout is designed using ExpressPCB version 7.5.0. The proposed system is capable of minimizing the power loss by up to 44% in comparison to the conventional light manage-ment system.

Static (SLS) and dynamic (DLS) light scattering techniques are assessed for their capacity to detect colloidal particles with diameters between d = 0.1 and 0.8 µm at very low concentrations in seawater. The detection limit of the apparatus was determined using model monodisperse spherical polystyrene latex particles with diameters 0.2 µm and 0.5 µm. It is shown that the concentration and size of colloids can be determined down to about 10^-6 g/L. Seawater obtained from different locations in western Europe was characterized using light scattering. It was found that seawater filtered through 0.45 µm pore size membrane filters was within the experimental error the same as that of ultrapure Milli-Q water containing the same amount of sea salt and no colloids could be detected with DLS. When the seawater was filtered through 0.8 µm pore size filters, colloidal particles were detected. The measurements show that the concentration of colloids in the seawater samples is not higher than 10^-6 g/L and that they have an average diameter of about 0.6 µm. We stress that these particles are not necessarily nanoplastics.

With the growing size and use of night lights time series from the Visible Infrared Imaging Radiometer Suite Day/Night Band (DNB), it is important to understand the stability of the dataset. All satellites observe differences in pixel values during repeat observations. In the case of night lights data, these changes can be due to both environmental effects and changes in light emission. Here we examine the stability of individual locations of particular large scale light sources (e.g. airports, prisons) in the monthly composites of DNB data from April 2012 to September 2017. The radiances for individual pixels of most large light emitters are approximately normally distributed, with a standard deviation of typically 15-20% of the mean. We observe geospatial autocorrelation in the monthly variations for nearby sites, while the correlation for sites separated by large distances is small. This suggests that local factors contribute most to the variation in the pixel radiances, and furthermore that averaging radiances over large areas will reduce the total variation. A better understanding of the causes of temporal variation would improve the sensitivity of DNB to lighting changes.

The term ‘biodynamic’ lighting is proposed as a term to capture the true aspiration of ‘life-centric’ lighting: good human and non-human outcomes for all life-sustaining behaviours on earth driven by good design for phototropism, phototaxis, photoperiodism and circadian entrainment. While future studies are necessary to consolidate this aspiration, it is clear that lighting has immediate potential to better support planetary health. As many aspects of animal, human and plantbehaviour and survival are being perturbed by widespread exposure to artificial light at night (ALAN), lighting professionals are in the middle, attempting to make design decisions that directly affect these life forms. This paper empowers readers with fundamental understandings of how light information is used by these life forms in a way crucial for development, growth and survival. The paper then provides a process for life-centric lighting design by drawing inspiration from an existing process for human-centric lighting design which can dovetail with decision-making processes that are within the workflow of lighting professionals. Holistic consideration of life-centric lighting design should look beyond altruism and romanticism by firmly rooting itself into pragmatism about long-term considerations for planetary health. Key references are consolidated and synthesized with goals of supporting knowledge translation into pragmatic lighting strategies in a manner useful for lighting professionals. While the scientific community remains sceptical about the term ‘biodynamic’ – which is argued to be developed through mysticism instead of scientific methodology – this paper counter argues that with appropriate use, the term has the potential to comprehensively capture this aspiration.

The Sun is a frame at relative rest in which sunlight travels at the emitted speed c. Earth travels at the revolving speed v in this frame. The reflection of light as a mechanical phenomenon applies to the modified Michelson interferometer employed by Miller in his experiments with light from the Sun. Unlike the Tomaschek experiments, which use light from stars that may travel in the Universe at velocities different from that of the Sun, the fringe shifts in the Miller experiments are predictable. Based on Michelson's derivation, Miller expected in his experiments at Mount Wilson a 1.12 fringe shift and observed a fringe shift of 0.08 in 1921 and 0.088 in 1925. The reflection of light as a mechanical phenomenon predicts zero fringe shift for Miller's experiment agreeing only with his observations at the Cleveland laboratory in 1924.

Studies on crop response to light quality [red (R) to far-red (FR) light ratio] often recommend early weed removal to reduce the effects of shade avoidance responses on crop yield. However, it is unclear whether crops are able to distinguish reflected light quality of kin from that of non-kin. We evaluated the response of sugarbeet (Beta vulgaris L.) to reflected FR light from sugarbeet, common lambsquarters (Chenopodium album L.), Kentucky bluegrass (Poa pratensis L.), alfalfa (Medicago sativa L.), and bare soil (control) under outdoor conditions in 2016 and 2017. Treatments were completely randomized with 10 replications per treatment. The study methods ensured there was no direct resource competition. The reflected R:FR of plant species ranged from 0.06 (common lambsquarters) to 0.24 (sugarbeet) compared to 0.7 for the bare soil. In both 2016 and 2017, there were 2 to 4 more leaves in the sugarbeet surrounded by soil compared to sugarbeet surrounded by neighboring species. There was up to 47, 57, 43, and 23% reduction in sugarbeet leaf area, shoot dry weight, root diameter, and root dry weight, respectively, due to reflected R:FR light from neighboring species. Sugarbeet did not respond differently to reflected light quality of kin compared to non-kin.

Blazars show rapid and high amplitude variability. In this work , Fermi daily light curve of 130 sources are analyzed, distribution of daily variability are compared with each other by using Kolmogorov-Smirnov (K-S) test. results show: 1)Some pairs of the distributions are similar; 2) In most cases, the distributions are not Gaussian.

In this work, we'll present the power spectra density, auto-correlation function, dentrended fluctuation analysis and multifractal spectrum are performed to the daily light curves of Blazars monitored by Fermi LAT. Some signs of power law are found.

Grape dehydration is practiced widely in the food industry with large yields of sultanas produced globally. This paper proposes an investigation into grape microstructure changes as it is dried by imaging specimens at intervals during dehydration at two temperatures using scanning electron microscopy. Detailed images of the microstructure were obtained, and a unique image processing algorithm was developed to quantitatively analyse the properties of this microstructure. Two main methods were developed to obtain the complex boundaries of cells present in the grape tissue in over 36 SEM images. Segmentation of the binary image using an adapted watershed function obtained the most consistent and accurate morphological shape. This was compared to a secondary method which used Canny’s edge detection function, morphological closing and skeletonizing to outlines the cellular microstructure. MATLAB was utilised to convert these boundaries into measurable areas so that quantitative data on average cell area, perimeter and cell axis lengths was acquired. It was found that over drying time cell area and perimeter reduced as expected. Some variability in the data was clear due to only single samples being analysed for each temperature and time combination. The development of automatic image processing techniques will enable quantitative data to be extracted from these images. Trends in cell perimeter, diameter and shape will be used to demonstrate relationships between morphological structure, drying temperature, and duration.

With the increased emphasis on competition in academic settings, anxiety is becoming more common, which inevitably has some impact on students’ learning process and result. This study aimed to explore how competition-induced anxiety influences the subjective cognitive load (SCL), attention level and test score. Meanwhile, we investigated the mediating role of the behavioral inhibition system/behavioral activation system (BIS/BAS) in those processes. A total of 101 college students were recruited in Study 1 to learn five micro-lectures from massive open online courses (MOOC) under with and without competitive conditions. The results showed that participants’ state anxiety (SA) scores were higher after the experiment, participants in the competition condition had higher test scores, and the relationship between SA/ trait anxiety (TA) and SCL could be mediated by the BIS. To obtain more objective data on learning processes (attention levels), we conducted Study 2, which collected behavioral and EEG data from 42 college students during the online learning. The results showed that the competition group had higher SA, lower attention levels, and worse test scores, and the relationship between SA/TA and attention levels could be mediated through the BIS. The present study not only expands previous research by finding that BIS functioning plays an important role in the effects of anxiety on cognitive load and attention, but also offers implications for using competitive strategies to motivate students according to their aptitude.

In our day-to-day life, Lie detection has a significant concern. We human beings are very much inaccurate while detecting the liars and We believe in what we are told. Lie detection is important in today’s life, because Concealing the information or faking it can sometimes take you to huge problems. In any areas like airport management[2], criminal investigations, counterterrorism, etc this concept has great importance. It is an evergreen challenging and changing topic. This paper presents the common technique which was followed up till now and why it was not considered effective and a review of Robust solutions to detection of deception. People generally do not[3] always believe on what someone says but also try to visualize their facial expressions. While in Robust solution these facial micro-expressions are identified, which are tiny, natural expressions seen on the individual’s face, when they try to conceal or suppress emotions. In addition, the article also provides the year-wise assessment and analysis of research articles published in the area of Lie detection from 2011 to 2022. In the end, our proposed framework for lie detection system is also presented. This paper cover up current issues as well as challenges that could be helpful to resolve in future research works. The review paper closes up by supporting future directions.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

The tissue micro environment or milieu consists of a highly dynamic population of cellular and non-cellular components which constitute a complex regulatory network aimed at maintaining the organ homeostasis. In the modern medicine the discovery of miRNAs is undoubtedly a promising field of research and they are essential in orchestrating immune system logic and their release in the gut micro milieu can directly affect bacterial gene expression. Here, we briefly review the role of microRNAs, focuses on their role on immune system components in physiological and pathophysiological gut micro milieu.

Background/Objectives: We defined the value of a machine learning algorithm to distinguish between the EEG response to no light or any light stimulation, and between red or green light stimulation in awake volunteers with closed eyelids. This new method of EEG analysis is visionary in the understanding of visual signal processing and will facilitate anaesthetic depth research. Methods: X-gradient boosting models were used to classify the cortical response to VEP stimulation (no light vs. any light stimulation; red vs. green light stimulation). For each of the two classifications, three scenarios were tested: training and prediction in all participants (all), training and prediction in one participant (individual), training across all but one participant with prediction in the participant left out (one out). Results: Ninety-four Caucasian adults were included. The machine learning algorithm had a very high predictive value and accuracy in differentiating between no light and any light stimulation (AUCROCall: 0.96; accuracyall: 0.94; AUCROCindividual: 0.96±0.05, accuracyindividual: 0.94±0.05; AUCROConeout: 0.98±0.04; accuracyo-neout:0.96±0.04). The machine learning algorithm was highly predictive and accurate in distinguishing between green and red colour stimulation (AUCROCall: 0.97; accuracyall: 0.91; AUCROCin-dividual: 0.98±0.04, accuracyindividual: 0.96±0.04; AUCROConeout: 0.96±0.05; accuracyoneout: 0.93±0.06). The predictive value and accuracy of both classification tasks was comparable between males and females. Conclusions: Machine learning algorithms could almost continuously and reliably differentiate between the cortical EEG responses to no light or any light stimulation and between green or red colour stimulation using VEPs in awake female and male volunteers with eyes closed. Our findings may open new possibilities for using VEPs in the intraoperative setting.

The increasing enhancement in the modulation accuracy of spatial light modulators has garnered significant attention towards real-time control technology for light fields based on these modulators. It has been empirically demonstrated that this technology possesses a remarkable capability to generate vector beams with arbitrary complex amplitude distributions. Nevertheless, past studies indicate that the generation of only one vector beam at a time has been observed. The simultaneous generation of numerous vector light fields can give rise to several challenges, including compromised picture quality, limited single mode operation, and intricate optical path configurations. In pursuit of this objective, we present a novel methodology that integrates the coding methodology of modified off-axis interferometric holography with the idea of optical superposition. This technique facilitates the concurrent generation of several vector beams. In this study, we present a demonstration of the simultaneous creation of twelve vector beams using a single spatial light modulator (SLM) as a proof of concept. Significantly, this technology has the ability to generate an unlimited quantity of vector light fields concurrently, under the assumption that the resolution of the SLM does not impose any limitations. The findings indicate that the imaging quality achieved by this technology is of a high standard. Furthermore, it is possible to separately control the beam waist radius, topological charge, polarization order, and extra phase of each beam.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

Derivation of light paths in the Michelson interferometer is based on the hypothesis that the speed of light does not change after reflection by a mirror in motion. The Michelson-Morley experiment predicts a fringe shift of 0.40. The same fringe shift is predicted for a particular Michelson interferometer in which the beam splitter of the interferometer makes an angle of 45° with the direction of light from the source. Light behaves like a wave and also as a particle. Thus, it is reasonable to consider the reflection of light as a mechanical phenomenon. With this hypothesis, the speed of light changes after reflection, and the predicted fringe shift for the particular Michelson interferometer is zero which is in accordance with the result of the Michelson-Morley experiment. Apparently, light travels in any inertial frame as if this particular interferometer belongs to a fixed frame. The velocity of light is considered independent of the velocity of its source, which is in accordance with astronomers’ observations of the binary stars, and the experiment performed at CERN, Geneva, in 1964.

Titanium micro-scale topography results in excellent osteoconductivity and bone-implant integration. However, the biological effects of sub-micron topography are unknown. We compared osteoblastic phenotypes and in vivo bone and implant integration abilities between titanium surfaces with micro- (1–5 µm) and sub-micro-scale (0.1–0.5 µm) topographies and machined titanium. Average roughness was 12.5 ± 0.65 nm, 123 ± 6.15 nm, and 24 ± 1.2 nm for machined, micro-rough, and sub-micro-rough surfaces, respectively. The micro-rough surface showed the fewest cells attaching during the initial stage and the lowest proliferation. Calcium deposition and expression of osteoblastic genes were highest on the sub-micro-rough surface and lowest on the machined surface. Bone-to-implant integration was strongest for the micro-rough surface, consistent with it having the greatest ability to retain cells in vitro. Thus, the biological effects of titanium surfaces are not necessarily proportional to the degree of roughness in osteoblastic cultures or in vivo. Sub-micro-rough titanium ameliorates the disadvantage of micro-rough titanium by restoring cell attachment and proliferation and enhances the rate of osteoblastic differentiation over that of micro-rough titanium; however, bone integration and the ability to retain cells are compromised due to its lower interfacial mechanical locking compared to that of micro-rough titanium.

Visible light communication (VLC) can offer the advantages of license and electromagnetic interference (EMI) free wireless transmission. As optical signal does not interference with the radio-frequency (RF) signal, VLC can be used to augment RF wireless communication to provide extra communication capacity while without degrading the performance of both signals. In order to achieve high performance VLC transmission, optical alignment between the optical transmit (Tx) and receiver (Rx) is very critical to enhance the received signal-to-noise ratio (SNR). Optical beam-steering at the Tx can be utilized to ensure narrow optical beam can reach the Rx; however, complicated and active tracking are required. Lenses or compound parabolic concentrators (CPCs) can be install in front of the Rx for focusing to enhance the SNR. However, these will limit the Rx field-of-view (FOV) and making the VLC transmission more subjected to misalignment issue. Hence, many creative optical antennas have been proposed and demonstrated using special optical materials as well as special Rx to enhance the FOV of VLC systems. However, they have their limitations, such as data rates and FOVs. In this work, we put forward and demonstrate a bi-direction free-space VLC system supporting multiple moveable Rxs using a light-diffusing optical fiber (LDOF). The downlink (DL) signal is launched from an head-end or central office (CO) far away to the LDOF at the client side via a free-space transmission. When the DL signal is launched to the LDOF, which acts as an optical antenna to re-transmit the DL signal to different moveable Rxs. The uplink (UL) signal is sent via the LDOF towards the CO. In a proof-of-concept demonstration, the LDOF is 100 cm long and the free space VLC transmission between the CO and the LDOF is 100 cm. 210 Mbit/s DL and 850 Mbit/s UL transmissions, meeting the pre-forward-error-correction bit error rate (pre-FEC BER = 3.8 × 10−3) threshold are achieved.

Indoor crop cultivation systems such as vertical farms or plant factories necessitate artificial lighting. Light spectral quality can affect plant growth and metabolism and, consequently, the amount of biomass produced and the value of the produce. Conflicting results on the effects of light spectrum in different plant species and cultivars make it critical to implement a singular lighting solution. In this study we explored the response of green and red leaf lettuce cultivars (’Aquino’, CVg, or ‘Barlach’, CVr, respectively) to long-term blue-enriched light application (WB). Plants were grown for 30 days in a growth chamber with optimal environmental condi-tions (temperature: 20°C, relative humidity: 60%, ambient CO2, Photon Flux Density (PFD) of 260 µmol m-2 s-1 over an 18-h photoperiod). At 15 days after sowing (DAS) white spectrum LEDs (WW) were compared to WB (λPeak = 423 nm) maintaining the same PFD of 260 µmol m-2 s-1. At 30 DAS, both lettuce cultivars resulted adapted to the blue light variant, though the adaptive re-sponse was specific to the variety. Rosette weight, light use efficiency and maximum operating efficiency of PSII photochemistry in the light, Fv/Fm’, were comparable between the two light treatments. Significant light quality effect was detected on stomatal density and conductance (20% and 17% increase under WB, respectively, in CVg) and, on the modified anthocyanin re-flectance index (mARI) (40% increase under WB, in CVr). Net photosynthesis response was gen-erally stronger in CVg compared to CVr; e.g. net photosynthetic rate, Pn, at 1000 µmol m-2 s-1 PPFD increased from WW to WB by 23% in CVg, compared to 18% in CVr. Results obtained suggest the occurrence of distinct physiological adaptive strategies in green and red pigmented lettuce cultivars to adapt to the higher proportion of blue light environment.

Since the recent legalization of medical and recreational use of cannabis (Cannabis sativa L.) in many regions worldwide, there has been high demand for research to improve yield and quality. With the paucity of scientific literature on the topic, this study investigated the relationships between light intensity (LI) and photosynthesis, inflorescence yield, and inflorescence quality of cannabis grown in an indoor environment. After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈ 425 μmol·m-2·s-1 and an 18-h light/6-h dark photoperiod, plants were grown for 12 weeks in a 12-h light/12-h dark ‘flowering’ photoperiod under canopy-level PPFDs ranging from 120 to 1800 μmol·m-2·s-1 provided by light emitting diodes. Leaf light response curves varied both with localized (i.e., leaf-level) PPFD and temporally, throughout the flowering cycle. Therefore, it was concluded that the leaf light response is not a reliable predictor of whole- plant responses to LI, particularly crop yield. This may be especially evident given that dry inflorescence yield increased linearly with increasing canopy-level PPFD up to 1800 μmol·m-2·s-1, while leaf-level photosynthesis saturated well below 1800 μmol·m-2·s-1. The density of the apical inflorescence and harvest index also increased linearly with increasing LI, resulting in higher-quality marketable tissues and less superfluous tissue to dispose of. There were no LI treatment effects on cannabinoid potency, while there were minor LI treatment effects on terpene potency. Commercial cannabis growers can use these light response models to determine the optimum LI for their production environment to achieve the best economic return; balancing input costs with the commercial value of their cannabis products.

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

Background: This study aimed to assess the impact of a nutrition-care bundle on growth and neurodevelopmental outcomes of micro-preterm infants born in a level III neonatal intensive care unit (NICU) by two years corrected age. Methods: A nutrition-care bundle emphasizing the prompt initiation of parenteral nutrition at birth, initiation of enteral feeds within 6 hours after birth, and early addition of human milk fortifiers was implemented in 2015 for infants born <26 weeks gestation. This before-and-after study evaluated growth and neurodevelopmental outcomes in infants born between 2012-2013 (before-nutrition-bundle BNB) and 2016-2017 (after-nutrition-bundle ANB). Results: A total of 145 infants were included in the study. Infants in the ANB group (n=73) were smaller (birthweight and gestational age), and there were more male infants and multiples included compared to the BNB group (n=72). Enteral feeds and fortifiers started earlier in the ANB group. Growth velocity and weight-z-score changes were similar in both groups during NICU stay and post-discharge. Systemic steroid use, but not cohort, was linked to lower Bayley scores across all domains. Conclusions: Implementing a nutrition-care bundle was not consistently associated with improved weight-gain and neurodevelopmental outcomes in the micro-preterm infant population, likely due to ongoing high-quality nutritional care by the clinical team.

It was for long time believed that lidar systems based on the use of high-repetition micro-pulse lasers could be effectively used to only stimulate atmospheric elastic backscatter echoes, and thus only exploited in elastic backscatter lidar systems. Their application to stimulate rotational and roto-vibrational Raman echoes, and consequently their exploitation in atmospheric thermodynamic profiling, was considered not feasible based on the technical specifications possessed by these laser sources until a few years ago. However, recent technological advances in the design and development of micro-pulse lasers, presently achieving high UV average powers (1-5 W) and small divergences (0.3-0.5 mrad), in combination with the use of large aperture telescopes (0.3-0.4 m diameter primary mirrors), allow to presently develop micro-pulse laser-based Raman lidars capable to measure the vertical profiles of atmospheric thermodynamic parameters, namely water vapour and temperature, both in daytime and nighttime. This paper is aimed at demonstrating the feasibility of these measurements and at illustrating and discussing the high achievable performance level, with a specific focus on water vapour profile measurements. The technical solutions identified in the design of the lidar system and their technological implementation within the experimental setup of the lidar prototype are also carefully illustrated and discussed.

Mass transfer is often the rate determining step for solid-liquid chemical reactions. Decrease of the concentration boundary layer thickness is essential to intensify the chemical reaction. Because the concentration boundary layer exists in the velocity boundary layer, force imposition in the concentration boundary layer by superimposing an electrical current and a magnetic field was proposed. Through, flow can be directly excited in the concentration boundary layer. The previous result indicates that by superimposing a DC current and a gradient magnetic field, the development of the concentration boundary layer was suppressed, because of a macro-scale flow excitation in the whole vessel. And by superimposing the gradient magnetic field with a modulate current, the development of the concentration boundary layer was further suppressed. This is because of the macro-scale flow enhancement and the excitation of a micro-scale flow near the solid-liquid interface. However, the mechanism for the micro-scale flow excitation has not been clarified. To clarify this, a uniform magnetic field was superimposed with the DC current or the modulate current. By this means, only the micro-scale flow was excited near the anode surface. The results found that the non-unform electromagnetic force distribution is the main reason for the micro-scale flow excitation.

As the scarcity of potable water increases, recycling of treated wastewater is increasing. Small-scale, decentralized treatment can be implemented to serve local populations by keeping water within their boundaries and within reach for reuse, particularly in less dense, non-urban communities. Availability of cellular networks and high-speed internet connectivity, along with significant reduction in cost, allows ongoing monitoring of decentralized treatment systems at a central location. In this paper a decentralized treatment system using micro nanobubble aeration, moving media and membranes is able to produce reusable water with low energy consumption, thereby allowing the use of solar energy in places with unreliable electrical supply. The treatment system, which uses no external chemicals, is able to operate unattended and deliver clear, disinfected water with non-detect suspended solids, BOD5 less than 10 mg/L and nutrients below 5 mg/L.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

We demonstrate a photonic RF integrator based on an integrated soliton crystal micro-comb source. By multicasting and progressively delaying the input RF signal using a transversal structure, the input RF signal is integrated discretely. Up to 81 wavelengths are provided by the microcomb source, which enable a large integration time window of ~6.8 ns, together with a time resolution as fast as ~84 ps. We perform signal integration of a diverse range of input RF signals including Gaussian pulses with varying time widths, dual pulses with varying time intervals and a square waveform. The experimental results show good agreement with theory. These results verify our microcomb-based integrator as a competitive approach for RF signal integration with high performance and potentially lower cost and footprint.

The relativistic effects of the dynamical properties of light at angular incidence were analyzed from the perspectives of Bohr indeterminacy and Heisenberg uncertainties and statistical dispersion. It was found that these effects report minimal uncertainties that agree with one or the other according to the angular range of incidence and that decrease with increasing refringence of the medium, constituting a specific relativistic uncertainty at angular incidence. An anomaly is indicated for the uncertainty principle in the Quantum Theory (QT) setting for small angles of incidence, where the accuracy of the angular position does not imply an increase in the uncertainty of the linear momentum. The anomalies arise because TQ does not predict the alternation between the classical and relativistic regimes of photon inertia at angular incidence. Specific relativistic uncertainty particularizes the uncertainty principle in the transmission of light between media pairs at angular incidence for the relativistic scenario, considering an observer that registers the relativistic effects of measurements that interfere with the observed system, in another inertial referential.

In any region of a space, the gravitational field cannot be eliminated. The speed of light in a vacuum has never been observed and cannot be observed with current technology. Till now, only the speed of light in a gravitational field has been observed. It results in that all the observed speed of light are always being varied by the gravity. Here, it is presented that light could be dispersion in a gravitational field analogous to the dispersion of light in the Newtonian prism experiment. The relativistic mass density on the surface of a neutron star is on the level of 10¹⁷kg/m³ while on the surface of the Earth is only 10^-7kg/m³, the effect of the gravitational field acting on the speed of light by a neutron star is much larger than that by the Earth. Therefore, the dispersion of light in strong gravitational field could be generally observed from the image of a star and it should have been observed through the double-image gravitational lensing and the spectroscopic binary system. And, it should affect the observed numbers, spectrogram, size and distance of the celestial objects.

Nowadays, microfluidics has become an anarchist interdisciplinary topic with considerable attention in a wide range of biotechnology applications. In this research work, numerical investigation of microfluidic micro-mixer is carried out using hybrid actuation approach with different micropillar shapes and gaps. For this purpose, COMSOL Multiphysics is used with three different physics such as thermoviscous acoustic to solve acoustic governing equations, laminar physics is used to solve fluid flow governing equations and diluted transport species is used to solve mixing governing equations. The simulations were carried out with flow velocity of 200 µm/s at both inlets with an oscillation frequency of 15kHz. The outcomes were in the form of acoustic characteristics such as acoustic pressure, acoustic velocity, acoustic streaming and mixing index. The results revealed that the inclusion of micropillars enhanced the mixing performance and strength of acoustic field resulting in improvement of mixing performance compared to the case without micropillars. In addition, it was also investigated that blade shape micropillars with 0.150 mm gaps deliver best results compared to the other cases with maximum and minimum values of the mixing index 0.95 and 0.72 respectively. The obtained results can be extremely helpful for design and modifications of hybrid microfluidics micro-mixer.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

Objectives: This study assessed the performance of a novel fluoride dentifrice containing micro- fibrillated cellulose (MFC) and 7% silica (Protegera™) versus common fluoride dentifrices. Methods: Removal of extrinsic stains was assessed using the pellicle cleaning ratio (PCR) method, and radioactive dentin abrasivity (RDA) was measured, to calculate a cleaning efficiency index (CEI). Fluoride efficacy was evaluated using widely used remineralization and fluoride uptake methods. Results: The MFC dentifrice removed stained pellicle significantly more effectively than the ADA reference material, Crest Cavity Protection™ and Sensodyne Pronamel™, and had equal performance to three known marketed stain-removing dentifrices (Arm & Hammer™ Advanced Whitening, Crest ProHealth™, and Colgate Optic White™). The MFC dentifrice vehicle had a low RDA (88), which was significantly less than Crest ProHealth (166) and Crest 3D-White™ (183). Based on PCR and RDA data, the CEI was 31% greater for the MFC product than for Crest ProHealth. In a 10-day pH cycling study, the fluoride efficacy of the MFC product was superior to a non-fluoridated control and was not significantly different from Sensodyne Pronamel and Crest Cavity Protection. The MFC dentifrice was superior for promoting fluoride uptake into incipient enamel lesions than the USP reference dentifrice. Conclusion: The low dentin abrasivity MFC dentifrice is highly effective in removing stained pellicle, and is an efficacious fluoride source when compared to other relevant commercially available fluoride dentifrices with high dentin abrasivity. Clinical Significance: Including micro-fibrillated cellulose into a fluoride dentifrice may enhance cleaning performance for the removal of external stain, while lowering abrasivity, and providing an effective fluoride source. This combination of benefits seems well suited to enamel protection and caries prevention.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Evaluating soil quality across various altitudinal gradients, both with and without vegetative cover, is crucial for the proper functioning of soil and optimal crop growth, thereby contributing to the sustainability of agroecosystems. Although the altitudinal gradient significantly influences soil quality, the ability to predict this quality, expressed through an index, in soils with and without vegetative cover, is still insufficiently explored. This study aimed to assess soil quality in the Jun Jun micro-watershed, located in the Tungurahua region, Ecuador. To achieve this objective, three categories of altitudinal gradients were selected: less than 2800 meters above sea level (masl), between 2800 and 2900 masl, and greater than 2900 masl. A total of 24 soil samples were collected in the mentioned gradients, considering both areas with and without vegetative cover. The indicators used included chemical and biological parameters such as soil organic carbon (OC), earthworm density (WD), earthworm biomass (WB), organic matter (OM), pH, total nitrogen (TN), and organic carbon (OC). The results revealed that in areas with altitudinal gradients below 2800 masl, soil quality index values were higher compared to other altitudes. In vegetated areas, a decrease in index values was observed as the altitudinal gradient increased, indicating a deterioration in soil quality with altitude. These findings are significant in providing a quantitative assessment of the effects of altitudinal gradient and vegetative cover influence on soil quality.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

A recent study reported that micro-osteoperforations (MOPs) accelerated tooth movement by activating alveolar bone remodeling. However, very little is known about the relationship between MOPs and external apical root resorption during orthodontic treatment. In this study, in order to investigate the mechanism which MOPs accelerate tooth movement without exacerbating the progression of root resorption, we measured the volume of resorbed root, and performed the immunostaining for the terminal deoxynucleotidyl transferase (TdT)-mediated dUTP-biotin nick-end-labelling method (TUNEL) exposed MOPs during rat experimental tooth movement. Male Wistar rats (11 week old) were divided into 3 groups: 10-g orthodontic force (optimal force) applied to the maxillary first molar (optimal force: OF group), 50-g orthodontic force application (heavy force: HF group) and 10-g force application plus 3 small perforations of the cortical plate (OF+MOPs group). On days 1, 4, 7, 10 and 14 after force application, the tooth movement and root volume were investigated by micro-computed tomography. Furthermore, the expression levels of apoptotic cells in pressure sides of periodontal ligament (PDL) and surround hard tissues were determined by TUNEL staining. The OF+MOP group exhibited a 1.8-fold increase in tooth movement on days 7, 10 and 14 compared with the OF group. On days 14, the HF group had a higher volume of root loss than the OF and OF+MOP groups. On the same day, the number of TUNEL-positive cells in the HF group increased at the root (cementum) site whereas that in the OF group increased at the alveolar bone site. Furthermore, that in the OF + MOP group increased at the alveolar bone site compared with the OF group. These results suggest that MOPs accelerate orthodontic tooth movement without exacerbating the progression of root resorption.

This research was aimed to apply probiotics in aquaculture to improve fish health and growth performances of Nile tilapia. Fingerlings with a mean initial body weight of 11.43±1.27 and mean initial body length of 6.2±0.84 were stocked in 12 happas. Fish were fed four times daily with four different diets having 30% crude protein at 5% of their body weight and reared for two months. The four diets were control diet, diets treated with Saccharomyces cervisiae, Lactobacillus fermentum and their combinations at a dosage of (1.5×108CFU/ml). Growth performance and gut pathogenic microbial of fish were investigated. Accordingly results indicated that the highest performance interims of body weight gain (33.43±1.65g), daily growth rate (0.51±0.05g), feed conversion ratio (1.89±0.10), and protein efficiency ratio (1.78±0.09) was achieved in fish fed with L. fermentum whereas, the lowest performance (19.83±2.23, 0.33±0.04, 3.52±0.39, and 0.97±0.11) respectively was achieved in fish fed with control diet. Salmonella, Shigella, E. coli and, Proteus were detected in gut of fish. In conclusion, the present study confirmed that Nile tilapia fed with probiotics Lac-tobacillus fermentum and Saccharomyces cerevisiae based diets improved growth and health of Nile tilapia reared under pond culture condition.

Both the use of plastic and its decomposition products lead to the distribution of plastic all over the earth and finally to the uptake by all kind of living beings including humans. Still, it is widely unknown what risks harbor the widespread uptake of plastics for human health, espe-cially regarding contributing factors like size, shape and surface composition. We assessed the uptake of polymethylmethacrylate (PMMA)-nano- and microbeads for HEK293-, A549- and MRC5 cells. Via confocal microscopy, we localized multiple PMMA-beads inside the cytosol of cells. Uptake of PMMA-beads did not alter cell growth and cell division, implying no short-term toxicity towards human cells. Further, we used a cAMP response element binding protein (CREB)-mediated reporter assay to assess whether internalized PMMA-nanobeads alter cell-signaling pathways. In contrast to the in vitro transcription, where the addition of PMMA-nanobeads abolished the transcription, no changes regarding CREB-mediated cell sig-naling are given in HEK293-cells. Our data led to the assumption that PMMA-nano-and mi-crobeads are internalized via endocytosis and end up as lysosomes within the cells cytosol. Therefore, we concluded differences regarding the surface composition of the PMMA-nanobeads mainly affect its potential to alter cell signaling. These findings emphasize the key role the sur-face composition plays regarding microplastic and its risks for human health.

This study aims to formulate binary cementitious systems containing silica fume (SF) and micro quartz (MQ) to improve cementitious concrete's durability and mechanical properties. In this investigation, we examined the effects of different essential variables, such as the level of SF and MQ replacement and the ratio of the water-binder (w/b). In this study, the w/b ratios were 0.25, 0.3, 0.35, and 0.4. Replacement levels for SF were 8, 10, and 12%, while replacement levels for MQ were 5, 8, 10, 15, 25, and 35%. The porosity and permeability decreased with an increase in replacement levels, regardless of the type of fine material used or the amount of replacement. Meanwhile, the strength increased markedly with SF replacement, reaching its maximum MQ of 25% at the SF level. The strength of the SF mixing was the highest in all mixes, and it remained the highest until 15% of MQ was replaced. The ultrafine size of MQ particles contributes to the improvement of compressive strength, porosity, and permeability in a similar way to SF particles, despite their high crystalline structure. Furthermore, in this study, analysis of variance (ANOVA) was employed to verify the influence of each variable on the studied response.

Abstract: Autophagy has a dual role in gliomagenesis in a microRNA-modulated environment. We investigated the potential relevance of autophagy in glioma development and survival by exploring the association of autophagy-associated genes and microRNAs in low- and high-grade gliomas. Real-time PCR (qPCR) was used to determine the expression of genes and microRNAs in 50 fresh glioma tissues while Formalin-fixed paraf-fin-embedded tissues of the same patients were used for immunohistochemistry. The Mann-Whitney U-test test, Spearman correlation test, and Kaplan-Meier survival analysis were performed to evaluate the expression, association, and overall survival in patients respectively. The expression of LC3, AKT, and miR-21 was increased in high-grade glioma compared to low-grade glioma while ULK2 expression was decreased in high-grade glioma. A strong positive correlation was observed for ULK2 with UVRAG, PTEN, miR-7, and miR-100, while the moderate correlation with mTOR, Beclin1, miR-30, miR-204, miR-374, miR-21 and miR-126 in low-grade glioma, while a moderate positive correlation between ULK2 and PI3K, PTEN, ULK1, VPS34, mTOR, Beclin1, UVRAG, AKT and miR-374, and between AKT and ULK1, VPS34, UVRAG, and miR-7 in high-grade gliomas. The low ULK2 and LC3 expression group was significantly associated with better overall survival in gliomas while miR-21 overexpression showed a poor prognosis in glioma patients. Therefore, miR-21, ULK2, and LC3 may serve as prognostic biomarkers for survival outcomes in glioblastoma.

Broadband noise reduction over the low-mid frequency range in the building and transportation sectors requires compact lightweight sound absorbers of typical sub-wavelength size. The use of multi-layered closely-spaced (micro-)perforated membranes or panels, if suitably optimized, contribute to these objectives. However, their elasticity or modal behaviors often impede the final acoustical performance of the partition. The objective of this study is to get insights into the vibrational effects induced by elastic limp membranes or panels volumetric modes on the optimized sound absorption properties of acoustic fishnets and functionally-graded partitions (FGP). Cost-efficient global optimization of the partition total frequency-averaged dissipation is achieved from simulated annealing with vibrational effects included through an impedance translation method. Critical coupling analysis reveals how the membranes or panels vibrations redistribute the locations of the Hole-Cavity resonances as well as their cross-coupling with the panels first volumetric mode. It is found that elastic limp micro-perforated membranes broaden the first pass-band of acoustic fishnets while smoothing out the dissipation ripples over the FGP optimiza-tion bandwidth. Moreover, the resonance frequency of the first panels mode sets an upper limit to the broadband optimization of FGPs, up to which high dissipation, low reflection and low trans-mission can be achieved.

Magnesium ions play an important immune-regulatory role during bone repair. For this study, we prepared micro-nano bioactive glass containing magnesium, which can release magnesium, silicon, and calcium ions and has a positive impact on osteogenic differentiation and vascular regeneration. In this study, MgMNBG was compounded and combined with PLGA and PCL for 3D printing. Afterwards, the physicochemical properties and bone repair performance of the scaffolds were evaluated through in vitro and in vivo experiments. We also investigated the effects of MgMNBG on osteogenic differentiation, immune regulation, and vascular regeneration. The results showed that MgMNBG can inhibit inflammation and promote osteogenesis and angiogenesis by regulating macrophages. PLGA/PCL/MgMNBG scaffolds have good osteogenic and angiogenic effects, and the composite scaffolds have excellent bone repair performance and potential application value.

Aluminum alloy (Al6061) sheet micro-hole processing is extensively used in smartphones, tablet PC, and smart wearable devices. The micro-hole processing is commonly performed using laser, micro drilling, microstamping, micro discharge, and chemical etching technologies. Micro-stamping technology is characterized by precision and rapid processing, but the precision positioning of the punch head and lower die is one of the major difficulties in micro-hole stamping, especially in manufacturing array micro-holes. This study used stamping without die technology. This technology uses an array punch head to punch the lower die holes on the base, then performs array micro-hole stamping. The experimental results show that a micro-hole array with 37 micro-holes were successfully manufactured and can be reproduced many times. Tapered array micro-holes with a high aspect ratio can be manufactured using this stamping without die technology; the micro-hole depth can be 260μm, the inlet diameter is 116μm, and the outlet diameter is 25μm. This study has successfully developed the feasibility of array micro-hole stamping technology.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries”, SC). Standardized Class-II cavities were made in sound molars having the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a BisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass, 20 wt.% T-DCPD (RBC-20); 20 wt.% Ba glass, 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced S. mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning Electron Microscopy and Energy-dispersive X-ray Spectroscopy characterized the specimens’ surfaces, while antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s test were applied at p<0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p<0.0001). Initial enamel demineralization could be observed only around RBC-0 and RBC-20 restorations. A direct antibiofilm activity could explain SC reduction by RMGIC, while a buffering effect on biofilm’s acidogenicity explained the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

This research was carried out with the objective of analyzing the principles of social and solidarity economy in the community funds of the rural sector of Pichincha, Ecuador. Small organizations promote microcredits for local, social and economic development, representing an alternative to those managed by traditional banks. The research was descriptive, non-experimental field research. The population analyzed consisted of 220 community funds, and the size of the representative sample was 49 community organizations that practice solidarity finance. The data were collected through online questionnaires using a Likert scale, and the validity of this approach was judged by experts; the reliability of the instrument obtained was 0.95 using the Cronbach’s alpha method. The results highlight that in these organizations, the following traits prevail: associativity, self-management and organization. However, autonomy and solidarity have a negative valuation, which shows that strategies must be rethought to achieve the empowerment of the financial service. This will allow them to be sustainable and to expand with more benefits that promulgate financial activity and promote structures in rural community networks that promote local development and strengthen deficient principles as a basis for generating a greater benefit to the partners.

Excitation of the acoustic field leading to the Blaha effect affects the plasticity of the material significantly in ultrasonic vibration-assisted forming. In a micro-forming field, the effects are more significant in the deformation in surface of materials [1]-[3], in which reduction of the surface roughness based on the increasing of plastic deformation of surface asperity was effective [4]. On the other hand, the effect on deformation behavior of the bulk region indicted reduction in the yield stress of materials, and not only acoustic effect [5], but also impact effect is found to generate a large amount of dislocation and produce plastic deformation [6][7]. However, the effect on the bulk is more significant as that on the surface. Differences in the effect on the surface and the bulk are not clarified. In this study, the mechanism of the deformation in the surface of the material with ultrasonic vibration assistance is investigated and compared with that in the bulk. Forging tests using a newly developed ultrasonic vibrator were carried out on pure Cu foils with various process conditions. The longitudinal vibration frequency of the ultrasonic transducer is 60∓2kHz, and the vibration amplitude is in an adjustable range of 0~10μm. Forging test was carried out at different initial stress, specimen size and amplitude. The difference in acoustic softening and impact effects on the surface and the bulk was discussed.

The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G net-works. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies in an attempt to retain the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, Buck-PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via PSIM Thermal Module, and using experimental data. The results indicate that multi-cell structures can improve the overall PSU ef-ficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implica-tions of this study, it is shown that the proposed multicell structure may increase the PSU costs by 10.78% but the payback pe-riod is in the order of just 3.3 years.