Highly macroporous thin films of WO₃ were fabricated on transparent conductive substrates by application of a polymeric organic paste loaded with an amine/tungstate complex. After spin-coating and annealing at 550^oC, the resulting yellow films are found to be comprised of channeled array of clustered nanoparticles. These channels are confirmed by scanning electron microscopy to extend through the entire length of the coating. The high porosity of the material enables the insertion of a co-catalyst into the internal structure of the film. These internally functionalized composites demonstrate good photosensitivity and stability in neutral electrolyte.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Thin Cu films with a thickness of ~0.5-2.5 mkm were obtained on the surface of Fe, V, and Ti metals using the Plasma Focus (PF) setup. The Cu film thickness was determined on an Ambios XP-200 profilometer. The distribution profiles of Cu, C, О2, N2 and H2 in initial metal samples: Fe, V, and Ti were studied by layer-by-layer analysis on a GDS 850A atomic emission spectrometer. It is shown that the distribution profile and the depth of occurrence of elements depend on the type of metal. Using the method of Rutherford Backscattering Spectrometry (RBS) of 4He+ ions, it was shown that for Cu atoms the depth of occurrence in Fe, V, and Ti, accordingly, is ~106, ~120, and ~160 nm. The depth of occurrence of C atoms in metals: Fe, V, and Ti is ~150, ~120, and ~200 nm, accordingly. From the data of layer-by-layer analysis on an atomic emission spectrometer in the initial samples of metals: Fe, V and Ti, a transition layer with a thickness of ~0.01, accordingly, was found; 0.5 and 1 mm. The presence of this layer is connected with the mechanical processing of metal samples, and the presence of a large number of admixtures in the thin layer of the metal. Thus, Cu atoms are located in the transition layer under the metal surface, which imparts adhesion and electrophysical properties of Cu films.

Rising consumer demand for more safety, healthy and fresh-like food has given new concepts for food packaging. Besides, the growing concern with environmental issues has increased the search for materials from non-petroleum sources and biodegradable ones. Thus, active films based on biopolymers loaded with natural active compounds have potential to be used as food packaging. However, there are a lot of lipophilic active compounds that are a problem to incorporate in hydrophilic matrices, such as polysaccharides and proteins. One way to overcome these challenges is adding these compounds encapsulated in O/W emulsions. The incorporation of emulsion in biopolymeric matrix has influence in the film properties, such as mechanical, barrier, optical, among other. In this way, this review aims to point out the main characteristics of the emulsions systems encapsulating active compounds and its influence in the film properties and to present and discus critically the recent advances in the area.

Regenerated silk (RS) is a protein-based “biopolymer” that enables the design of new materials; here, we called “bionic” the process of regenerated silk production by a fermentation-assisted method. Based on yeast’s fermentation, here we produced a living hybrid composite made of regenerated silk nanofibrils and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, by fermentation of such microorganisms at room temperature in a dissolution bath of silkworm silk fibers. The fermentation-based processing enhances the beta-sheet content of the RS, corresponding to a reduction in water permeability and CO₂ diffusion through RS/yeast thin films enabling the fabrication of a mechanically robust film that enhances food storage durability. Finally, a transfer print method, which consists of transferring RS and RS/yeast film layers onto a self-adherent paraffin substrate, was used for the realization of heat-responsive wrinkles by exploiting the high thermal expansion of the paraffin substrate that regulates the applied strain, resulting in a switchable coating morphology from the wrinkle-free state to a wrinkled state if the food temperature overcomes a designed threshold. We envision that such efficient and smart coatings can be applied for the realization of smart packaging that, through such a temperature-sensing mechanism, can be used to control food storage conditions.

Antimicrobial resistance (AMR) has become a worldwide health problem. Consequently, there is a global interest in the study of the antimicrobial activity of natural compounds as an alternative to antibiotics. One of the possibilities studied during the last years is the use of bacteriophages and their derived proteins. More specifically, phage lytic proteins or endolysins are specific enzymes that cause cell lysis and can be easily produced and purified after overexpression in bacteria. However, one of the major disadvantages of these proteins is their sensitivity to some environmental conditions that can reduce their efficiency. The use of vesicles for endolysin encapsulation could help overcome this disadvantage, offering an additional protection to the protein and allowing its controlled release and long-term stability.

Antimicrobial peptides (AMPs) have emerged as a promising class of bioactive molecules with the potential to combat infections associated with medical implants and biomaterials. This review article aims to provide a comprehensive analysis of the role of antimicrobial peptides in medical implants and biomaterials, along with their diverse clinical applications. The incorporation of AMPs into various medical implants and biomaterials has shown immense potential in mitigating biofilm formation and preventing implant-related infections. We review the latest advancements in biomedical sciences and discuss the AMPs that were immobilized successfully to enhance their efficacy and stability within the implant environment. We also highlight successful examples of AMP coatings for the treatment of surgical site infections (SSIs), Contact lenses, Dental Applications, AMP-Incorporated Bone Grafts, Urinary tract infections (UTIs), Medical Implants, etc. Additionally, we discuss the potential challenges and prospects of AMPs in medical implants, such as effectiveness, instability and implant-related complications. We also discuss strategies that can be employed to overcome the limitations of AMP-coated biomaterials for prolonged longevity in clinical settings.

Plasma polymerized (PP) thin films deposited in a soft or intermediate plasma discharge from hexamethyldisiloxane (HMDSO) were developed as sensors for the detection of volatile organic compounds (VOCs) vapors. Energy dispersive X-ray spectroscopy (EDX) and X-ray reflectometry (XRR) were performed to determine the organosilicon films elemental composition and density. Spectroscopic ellipsometry measurements were carried out to determine the refractive index of the films. Quartz crystal microbalance (QCM) and ellipsometry coupled to vapor sorption were used to investigate the sorption mechanism of several VOCs vapors into the films as a function of the plasma deposition conditions. The density and the refractive index of the PP-HMDSO films increased with the plasma energy due to a different chemical composition and different proportion of free volumes in the material network. The PP-HMDSO films showed different affinities towards the VOCs vapors depending on the plasma discharge energy. The films elaborated in the lowest plasma energy revealed a good sensitivity towards the VOCs especially toluene (one of the BTEX vapors) compared to the other films deposited under higher plasma energy. In addition, the selectivity between toluene and other non-BTEX VOCs such as heptane and ethanol decreased to become zero while increasing the plasma energy.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Research and development on innovative packaging materials have advanced significantly to safeguard packaged food against microbial contamination and oxidation. To combat demanding issues, active packaging has evolved as a viable method for minimizing oxidation/microbial growth in packaged goods, extending their shelf life, and ensuring the consumer's safety. Active food packaging includes O2, CO2 scavengers, moisture absorbers, U.V. barriers, and carriers of antioxidant and antimicrobial agents. Various antimicrobial agents are carried and/or incorporated into food packaging formulations. Consumers demand natural antimicrobials over chemical/synthetic ones, such as bacteriocins, bacteriophages, and essential oils. Bacteriophages (viruses) have emerged as a feasible option for decontaminating and eliminating infections from food sources. These viruses can target specific food-borne pathogens without impairing beneficial bacteria and, most critically, without causing disease in humans or animals. Fortifying bacteriophages into food packaging films will not only kill specific food microorganisms but has evolved as a new weapon to combat antimicrobial-resistant (AMR) issues. The present review summarises recent developments in active antimicrobial packaging focused particularly on bacteriophage-food packaging applications and advantages, drawbacks, and future trends for active food packaging.

Highly transparent thin films with the chemical formula BaSrMgWO6 were deposited by spin coating using a solution of nitrates of Ba, Sr and Mg and ammonium paratungstate in dimethylformamide with a ratio Ba:Sr:Mg;W=1:1:1:1. XRD, SEM, EDX and XPS investigations evidenced that an annealing at 800 ºC for 1h leaves the structure amorphous with a precipitate on the surface and that a supplementary annealing at 850 ºC for 45 min forms a nanocrystalline structure and dissolves a part of precipitates. It was evidenced a textured double perovskite cubic structure (61.9%) decorated with tetragonal and cubic impurity phases (12.7 %) like BaO2, SrO2 and MgO and an under-stoichiometric phase (24.4%) with the chemical formula Ba2-(x+y) SrxMgyWO5. From transmittance measurements the values of optical band gap were estimated for the amorphous (Eg= 5.15) and nanocrystalline (Eg=4.58 eV) phases. The presence of a lattice disorder was indicated by the high values of Urbach and weak absorption tail energies A decrease in their values was observed and attributed to the crystallization process and cation redistribution.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

The main aspects of mercury sulfide and mercury selenide thin film synthesis using the chemical deposition method are considered. An analysis of various factors affecting film properties was conducted, including the study of how the nature of the substrate and its pre-treatment influence film properties. The effects of the working solution's temperature, deposition time, and annealing conditions on film characteristics were investigated. The impact of these parameters on the phase composition, as well as optical, electrical, and morphological properties of the films, is discussed and summarized. The paragraph also explains how the choice and concentration of initial reagents affect the parameters, characteristics, and properties of the obtained films.

Hard coatings like Titanium diboride (TiB2) on silicon substrates are used for interconnects. micro-electro-mechanical devices and metallurgical protective coatings were analyzed based on shallow depths of nanoindentation penetration which involves a change in the nature of the contact from Hertzian to Pyramidal both in loading as well as unloading modes. Features like ductile fracture, linear unloading, and the creation of electrical conduction paths were analyzed. These high-precision features are influenced by the thickness and crystalline nature of the films and are significant for device fabrication.

A method based on ferroelectric dipole to enhance surface charge density of triboelectric generator was proposed. By using the ferroelectric properties of polyvinylidene fluoride (PVDF), a positive charge trap was formed in the triboelectric layer to enhance the electric generating performance of the triboelectric material, so as to improve the surface charge density of the triboelectric nanogenerator. The PVDF film was fabricated by casting and uniaxial tensile process, and integrated into the triboelectric nanogenerator with vertical separation structure. The influences of the embedding direction, thickness and polarization intensity of the PVDF film on the output of the triboelectric nanogenerator were systematically studied. The results showed that the embedded PVDF piezoelectric film with a thickness of 100 µm and a maximum polarization electric field of 90 MV/m increased the peak power of the triboelectric nanogenerator by 2.6 times. This work has provided a new insight into regulating the properties of the triboelectric nanogenerator.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

This study developed gelatin-based films with incorporation of microcrystalline cellulose as reinforcement material. Clove (Syzygium aromaticum), nutmeg (Myristica fragrans), and black pepper (Piper nigrum) oleoresins containing antimicrobial compounds of natural origin were incorporated into films. The mechanical, thermal, optical, and structural properties, as well as color, resistance to sealing and permeability to water vapor, light, and oil of the films were determined. Adding oleoresins to the gelatin matrix increased elongation of the material and significantly diminished its permeability to water vapor and oil. Evaluation of the potential use of films containing different oleoresins as bread packaging material was influenced by the film properties. The biocomposite film containing oleoresin from black pepper was the most effective packaging material for maintaining the bread’s quality characteristics.

The manuscript presents the optical properties of directly deposited films of gold nanoparticles (AuNPs) prepared by ultrasonic spray pyrolysis technology. Four samples were produced, with an AuNPs deposition time of 15 min, 30 min, 1h and 4h on the glass substrate. The morphological characterization of the deposited films showed that the size of the first deposited AuNPs is between 10 and 20 nm, while with a longer duration of the deposition process, larger clusters of AuNPs grow by coalescence and aggregation. The prepared layers were optically characterised with Ultraviolet–visible spectroscopy (UV-vis) and ellipsometry. The ellipsometric measurements showed an increasingly denser and thicker effective thickness of the AuNPs layers. The extinction spectra display a clear local surface plasmonic resonance (LSPR) signature (peak 520-540 nm), indicating the presence of isolated particles in all samples. For all AuNPs layers, the imaginary part of both ε// and ε⏊ is dominated by a central peak around 2.2 eV corresponding to the LSPR of isolated particles and a high-energy shoulder due to Au interband transitions. It is shown that, as the density of particles increases, the extinction cross section grows over the whole spectral range where measurements are taken. Thus response can be explained with an enhanced electromagnetic response among AuNPs, that can be connected to the increase of particle density but also by the formation of clusters and irregular structures.

The exchange coupling between two ferromagnetic thin films, one with magnetically hard and the other with soft phases, separated by a thin non-magnetic layer is studied. Nd-Fe-B/ Ti / Fe thin film heterostructures were fabricated using DC magnetron sputtering on Si substrates which were heated in situ at 650°C using a house-built vacuum-compatible heater. The effect of the thickness of the Ti buffer layer and the annealing temperature on the formation of various phases of NdFeB was investigated. The effect of the thickness of the non-magnetic Ti spacer layer on the exchange coupling strength between the hard phase Nd-Fe-B ferromagnetic thin layer and the soft phase transition metal Fe layer was experimentally investigated. Hysteresis loops of multilayer thin films indicate an antiferromagnetic coupling was observed when the thickness of the spacer layer was 2 nm. This is within the range of antiferromagnetic coupling calculation based on RKKY theory predictions.

The effect of ferromagnetic CaMnO3 (CMO) addition on structural, magnetic, dielectric, and ferroelec-tric properties of BiFeO3 are presented. X ray diffraction and Raman investigation allowed the identifi-cation of single pseudo cubic perovskite structure. The magnetic measurement showed that the pre-pared films exhibit a ferromagnetic behavior at low temperature with both coercive field and remnant magnetization increased with increasing CMO content. However, a deterioration of magnetization was observed at room temperature. Ferroelectric study revealed an antiferroelectric like behavior with a pinched P-E hysteresis loop for 5%CMO doping BFO resulting in low remnant polarization and double hysteresis loops. Whereas, high remnant polarization and coercive field with a likely square hysteresis loop are obtained for 10 % CMO addition. Furthermore, a bipolar resistive switching behavior with a threshold voltage of about 1.8V is observed for high doped film that can be linked to the ferroelectric polarization switching.

A novel manufacturing process is presented for producing Nano powders and thin films of CuCoO₂ (CCO) material. This process utilizes three cost-effective synthesis methods: hydrothermal, sol-gel, and solid-state reactions. The resulting delafossite CuCoO₂ samples were deposited onto transparent substrates through spray pyrolysis, forming innovative thin films with a Nano crystal powder structure. Prior to the transformation into thin films, CuCoO₂ powder was first produced using a low-cost approach. The precursors for both powders and thin films were deposited onto glass surfaces using a spray pyrolysis process, and their characteristics were examined through X-ray diffraction, scanning electron microscopy, HR-TEM, UV-visible, and Electrochemical impedance spectroscopy (EIS) analyses was conducted to determine the conductivity in transversal direction of this groundbreaking material for solar cell applications. On the other hand, the sheet resistance of the samples was investigated using the four probe-method to obtain the sheet resistivity and them calculate the in plane conductivity of the samples. We also investigated the aging characteristics of different precursors with varying durations. The functional properties of CuCoO2 samples were explored by studying chelating agent and precursor solution aging periods. Resuming, this study thoroughly discusses the synthesis of delafossite powders and their conversion into thin films, which hold potential as hole transport layers in transparent optoelectronic devices.

Films obtained from a main biopolymer phase of fish gelatin (GelA, 3% w/w) encapsulated with cinnamon essential oil (CEO, 0.03 – 0.48% v/w) and loaded with bacterial cellulose nanocrystals (BCNCs, 0.06% w/w) at pH = 3.5 were characterized. CEO-GelA/BCNCs films were prepared by casting and analyzed in terms of thickness, light transmittance (TT) and haze (H), surface hydrophobicity, tensile properties, chemical composition, and water solubility (WS). All tested films displayed outstanding optical properties (TT > 89.4%), with haze slightly exceeding a 3% value only when the highest CEO loading was used during nanoemulsion preparation. The CEO plasticizing effect yielded an increase in the elongation at break (EAB, from 0.84% up to 3.79%), which corresponded to a decrease in tensile strength (TS, from 8.98 MPa down to 1.93 MPa). The FT-IR spectra of films revealed a good degree of interaction among single nanoemulsion components via hydrogen bonding. The intrinsic hydrophobic nature of the CEO negatively impacted the WS (from 52.08% down to 8.48%) of the films. Results obtained in this work confirmed the possibility to produce packaging systems from renewable sources to be potentially used in the form of edible films/coatings for preserving water-sensitive food products, both vegan-based (fruits/vegetables), and animal-based (meat/seafood).

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

As a novel post-harvesting strategy, edible films and coatings for fruits and vegetables offer preservation measures to meet the growing needs of hunger and agricultural management. Albeit edible films and coatings would differ in their processing and physio-mechanical characteristics, but functionality is distinctly the same as they are designed to improve shelf-life, barrier, and nutritional properties of the food. With emerging concerns on sustainability, biomacromolecules have been widely considered for preparing edible films and coatings, which are Generally Recognized as Safe (GRAS) substances. Biopolymers, including polysaccharides, proteins, and lipids are the main sources of preparing edible films and coatings. These biomacromolecules make stable colloidal dispersions that deliver processing convenience with various formulation, blending, casting, coating, and film-forming methods. However, biopolymers based edible films and coating require improvements for their extended performance due to several structural and barrier limitations. Therefore, preparing blends and composites, incorporating target molecules to introduce different functionalities, and designing complex multilayers are among the many recent research approaches developed to overcome those limitations. Thereby ensuring enhanced food preservation and extended shelf-life, essential requirements of food waste management without or with minimal influence on the texture, flavor, and nutritional value of food and vegetables.

The concern about consuming eco-friendly products has motivated research in the development of new materials. Therefore, films based on natural polymers have been used to replace traditional polymers. This study consists of a production of films based on gelatin reinforced with black pepper essential oil-loaded nanoemulsions and Cloisite Na⁺. The films were characterized by water vapor permeability, mechanical and thermal properties, surface contact angle, X-ray diffraction and scanning electron microscopy. It was observed that the films containing the nanoemulsion have higher permeability values and an increase in their mechanical resistance. The addition of nanoclay contributed to an increase in the surface hydrophobicity of the film and an increase in the tensile strength at break by about 150%. The addition of essential oil nanoemulsions led to an increase in thermal stability. The presence of clay dispersion contributed to the formation of a surface that was slightly rougher and grainier. The addition of the black pepper essential oil nanoemulsion resulted in an increase in porosity of the gelatin matrix. Through X-ray diffraction analysis, it was possible to conclude that both the polymeric gelatin matrix and the essential oils nanoemulsion are intercalated with the clay dispersion.

In this paper, a novel synthesis for a chemical precursor for nanocrystalline VO2 coatings is elaborated. The compatibility of the precursor towards the substrate is optimized for spin coating. This is done by subjecting multiple solvents to contact angle measurements. A suitable thermal treatment is developed to densify the coating and to induce crystallization. Afterwards the microstructure of the coating is investigated using X-Ray diffraction, electron microscopy and ellipsometry techniques. To assess the thermochromic properties of the fabricated device, optical transmission experiments were conducted both at room temperature and at elevated temperature. A correlation between these thermochromic properties and coating thickness was investigated in order to obtain an optimized thermochromic device, where both high visual transparency and prominent thermochromic switching abilities are aimed for. In this work, an optimal coating thickness is proposed for a thermochromic coating with high switching ability and solar modulation.

The light response and resistance switching behavior in BaTiO3 (BTO) films are studied for a symmetric Pt/BTO/Pt structure. The resistance of films as a function of time with and without ultraviolet light has been studied. Furthermore, resistance switching behavior was clearly observed based on the application of 365 nm wavelength ultraviolet light. Consequently, the polarities of resistance switching can be controlled by ultraviolet light when the energy is larger than the band excitation energy. It is proposed that the polarity of the resistance switching is dictated by the competition of the ferroelectricity and oxygen vacancy migration. This provides a new mechanism for modulating the state of ferroelectric resistive memory devices.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

Ultrathin Bi₂Se₃-NbN bilayers comprise a simple proximity system of a topological insulator and an s-wave superconductor for studying gating effects on topological superconductors. Here we report on 3 nm thick NbN layers of weakly connected superconducting islands, overlayed with 10 nm thick Bi₂Se₃ film which facilitates enhanced proximity coupling between them. Resistance versus temperature of the most resistive bilayers shows insulating behavior but with signs of superconductivity. We measured the magnetoresistance (MR) of these bilayers versus temperature with and without a magnetic field H normal to the wafer (MR=[R(H)-R(0)]/\{[R(H)+R(0)]/2\}), and under three electric gate-fields of 0 and ±2 MV/cm. The MR results showed a complex set of gate sensitive peaks which extended up to about 30 K. The results are discussed in terms of vortex physics, and the origin of the different MR peaks is identified and attributed to flux-flow MR in the isolated NbN islands and the different proximity regions in the Bi₂Se₃ cap-layer. The dominant MR peak was found to be consistent with enhanced proximity induced superconductivity in the topological edge currents regions. The high temperature MR data suggest a possible pseudogap phase or a highly extended fluctuation regime.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

Copper-nitride (Cu3N) material is attracting much attention as a potential next-generation thin-film solar-light absorber. In this work, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron sputtering, at room temperature,onto glass and silicon substrates. The optical properties of the Cu3N thin layers were studied by spectroscopic ellipsometry and transmission, to achieve a low-cost absorber material to replace conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by FIB-SEM microscopy and FTIR spectroscopy.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

Polarisation analysis in the mid-infrared fingerprint region was carried out on thin (∼1μm) Si and SiO2 films evaporated via glancing angle deposition (GLAD) method at 70∘ to the normal. Synchrotron-based infrared microspectroscopic measurements were carried out on the Infrared Microspectroscopy (IRM) beamline at Australian Synchrotron. Specific absorption bands, particularly Si-O-Si stretching vibration, was found to follow the angular dependence of ∼cos2θ, consistent with the absorption anisotropy. This unexpected anisotropy stems from the enhanced absorption in nano-crevices, which have orientation following the cos2θ angular dependence as revealed by Fourier transforming the image of the surface of 3D columnar films and numerical modeling of light field enhancement by sub-wavelength nano-crevices.

Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

We present organic, diamagnetic materials based on structurally simple (hetero-) tolane derivatives. They form crystalline thin-film aggregates that are suitable for Faraday rotation (FR) spectroscopy. The resulting new materials are characterized appropriately by common spectroscopic (NMR, UV-Vis), microscopy (POM), and XRD techniques. The spectroscopic studies give extremely high FR activities thus makes these materials promising candidates for future practical applications. Other than a proper explanation, we insist in the complexity of designing efficient FR materials starting off from single molecules.

Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

The stability and composting behaviour of monolayers and laminates of poly(lactic acid) (PLA) and starch with and without active extracts and cellulose fibres from rice straw (RS) were evaluated. The retrogradation of the starch throughout storage (1, 5, and 10 weeks) gave rise to stiffer and less extensible monolayers, with lower water vapour barrier capacity. In contrast, the PLA monolayers, with or without extract, did not show marked changes with storage. However, these changes were more attenuated in the bilayers that gained water vapour and oxygen barrier capacity during storage, maintaining the values of the different properties close to the initial range. The bioactivity of the active films exhibited a slight decrease during the storage, the antioxidant capacity being better preserved in the bilayers. All monolayer and bilayer films were fully composted within 90 days, but with different behaviour. The bilayer assembly enhanced the biodegradation of PLA whose monolayer exhibited a lag period of about 35 days. The active extract reduced biodegradation rate of both mono and bilayers but does not limit the material biodegradation within the time stablished in the Standard. Therefore, PLA-starch laminates, with or without the valorised fractions from RS, can be considered as biodegradable and stable materials for food packaging applications.

This article describes the synthesis of hydroxyapatite (HAp) flakes through a microwave-assisted hydrothermal method. These flakes are intended for use as substrates for depositing titanium dioxide (TiO2) films using chemical vapor deposition with metal–organic precursors (MOCVD). The results reveal the formation of crystalline hydroxyapatite characterized by a uniform mor-phology. Additionally, we demonstrated the successful deposition of TiO2 coatings on the hy-droxyapatite flakes, resulting in a distinctive faceted prism morphology. Our findings affirm the effective synthesis of the HAp/TiO2 composite material. To further explore the material’s practical applications, we recommend assessing the photocatalytic activity of these composite membranes in future research.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

The purpose of this research work was to synthesis bio-derived nanocomposite films by incorporating Na0.5Bi0.5TiO3 (NBT) nanoparticles into Chitosan matrix. The NBT nanoparticles were synthesized using a traditional solid-state technique. Then, through a solution casting approach, flexible composite films were fabricated using Chitosan polymer. The morphology and structural assessments were carried out utilizing scanning electron microscopy (SEM), X-ray diffraction and fourier transform infrared technique. The SEM micrographs showed that NBT nanoparticles were randomly distributed and interconnected with other particles, forming interconnected grains with substantial interspaces within the matrix. The spectral response between 300 and 800 nm of the composites is mainly governed by light scattering of NBT particles with diameter sizes in the 100 - 400 nm range and the bandgap of the NBT phase. The dielectric studies demonstrated that the composite films exhibited higher dielectric values compared to the pure Chitosan film. Besides, the increase of NBT amount was found to increase the dielectric values. Additionally, local piezoelectric measurements reveal the expected piezoelectric and ferroelectric behavior for the NBT particles dispersed into the polymer matrix, as locally probed by Piezoresponse Force Microscopy. The studied system bears interest for advanced biocompatible opto- and piezo-electric materials.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

Luminescent properties of epitaxial Cu2O thin films were studied in 10-300 K temperature range and compared with luminescent properties of Cu2O single crystals. Cu2O thin films were deposited epitaxially by the electrodeposition method on either Cu or Ag substrates at different processing parameters, which determined the epitaxial orientation relationships and encapsulated surface. Cu2O (100) and (111) single crystal samples were cut from a crystal rod grown by the floating zone method. Luminescence spectra of thin films contain the same emission bands as single crystals around 720, 810 and 910 nm, characterizing VO2+, VO+ and VCu defects, correspondingly. Additional emission bands, whose origin is under discussion, are observed around 650-680 nm, while the exciton features are negligibly small. The relative mutual contribution of the emission bands varies depending on the particular thin film sample. Existence of the domains of crystallites with different orientation determines the polarization of luminescence. PL of both Cu2O thin films and single crystals is characterized with negative thermal quenching in the low temperature region, the reason of this phenomenon is discussed.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

The current pandemic is urgently demanding to discover alternative materials capable of inactivate the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) that causes the coronavirus 2019 (COVID-19) disease. Calcium alginate is a crosslinked hydrophilic biopolymer with an immense range of biomedical applications due to its excellent chemical, physical and biological properties. In this study, the cytotoxicity and antiviral activity of calcium alginate in the form of films were studied. The results showed that these films are biocompatible in human keratinocytes and are capable of inactivating enveloped viruses such as bacteriophage phi 6 with a 1.43-log reduction (94.92% viral inactivation) and SARS-CoV-2 Delta variant with a 1.64-log reduction (96.94% viral inactivation) in virus titers. The antiviral activity of these calcium alginate films can be attributed to its negative charge density that may bind to viral envelopes inactivating membrane receptors.

The detection of hormones, pharmaceutical and personal care products (PPCPs), in aqueous complex media as water bodies is an urgent and mandatory matter because of its harmful impact on the environment. This work presents a sensor device which is able to detect trace of the synthetic hormone 17α-ethinylestradiol (EE2), in a range of concentration of 10-15 to 10-9 M in both mineral and tap waters. These types of water were studied due to their different degrees of complexity, which allow to attain a better understanding of EE2’s behavior and response in different media. The sensor body consists of solid supports having interdigitated electrodes without and with a thin film deposited on it, and device response is evaluated through impedance spectroscopy. The thin films were prepared by the layer-by-layer technique from aqueous solutions of polyethylenimine (PEI) and poly(sodium 4-styrenesulfonate) (PSS) polyelectrolytes. Results demonstrated that it is possible to discriminate clearly the different waters used and to detect EE2, obtained from the second principal component (PC2) as a result of the application of principal component analysis method, with a sensitivity of -0.072 ± 0.009 and -0.44 ± 0.03 per decade of concentration, for mineral and tap water, respectively. Detection limits values were found to be of 8.6 fM (2.6 pg/L) and of 7.5 fM (22.2 pg/L) for TW and MW, respectively and are lower than the ones found in literature. Moreover, the achieved constant proportionality between the PC2 values for each EE2 concentration reveals that one can use this methodology to quantify EE2 concentration in unknown aqueous complex matrices.

Polydopamine (PDA) deposition, obtained from the oxidation of dopamine and other catecholamines is an universal way to coat all known materials with a conformal coating which can subsequently be functionalyzed at will. The structural analogies between polydopamine and eumelanin, the black-brown pigment of the skin, incited to produce stable polydopamine nanoparticles in solution instead of amorphous precipitates obtained from the oxidation of dopamine. Herein, we demonstrate that size controlled and colloidally stable PDA based nanoparticles can be obtained in acidic conditions, where spontaneous auto-oxidation of dopamine is suppressed, using sodium periodate as the oxidant and a protein like alkaline phosphatase as a templating agent. The size of the PDA@Alp nanoparticles depends on the dopamine/enzyme ratio and the obtained particles display the enzymatic activity of alkaline phosphatase with an activity extending up to two weeks after particle synthesis. The PDA@ alkaline phosphatase (Alp) nanoparticles can be engineered in polyelectrolyte multilayered films to potentially design model biosensors.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

The Aminofunctional starch/Carboxylated nitrile butadiene rubber (ANS/XNBR) latex films were prepared with control (0), 5, 10, 15, and 20 phr of ANS loadings. The films were subjected to soil burial test for 8 weeks, which recovered every two weeks to quantify the degraded properties. The control (week 0) and biodegraded films were subjected to physical tests (crosslink density, tensile, and tear strength tests) and biodegradation quantification (mass loss retention, and water vapor transmission rates). The optimum physical properties of ANS/XNBR films were subjected to further assessment of its degradation properties which include morphological (optical and scanning electron microscopes (SEM)), Fourier transform infrared (FTIR) analysis, and thermogravimetric analysis (TGA) respectively. Overall, mechanical properties of biodegraded ANS/XNBR latex films decreased as biodegradation period elapses. The biodegradation assessment via water vapor transmission rates and mass loss analyses indicates the high degree of biodegradation rates were observed with higher loading of ANS/XNBR latex films. Morphological analyses via optical microscope shows the transformation of the films surface opacity during biodegradation test. SEM images depicted the microorganism remains on the film surfaces. For FTIR analysis, the most significant changes in the spectras of the films appeared in the region of 790–3000 cm⁻¹. TGA thermograph shows the thermal retention of the materials decreased, as the biodegradation period elapses for optimum ANS/XNBR latex films. From the results obtained, ANS/XNBR latex films shows optimum degradation and mechanical properties at 10 phr filler loading.

Star copolymer films were studied for confirming the role of film morphology in antimicrobial activity previously reported. With this scope, films of a two-branches copolymer, namely m-PEG-(MMA-ran-DMAEMA)2, containing ≈ 40 % in mol of non-quaternized 2-(dimethylamino)ethyl methacrylate, were produced by using spin-coating, drop-casting and casting deposition techniques, thus obtaining ultra-thin, thin and thick films, respectively. The morphology is generally flat for thin and thick films, but it becomes substrate dependent for ultra-thin films where the film planarization effect is not efficient. Mechanical properties of such films were investigated by Force Volume Maps in both air and liquid. In air, ultra-thin films are in the substrate-dominated zone and thus the elastic modulus E is overestimated, while E reaches its bulk value for thin and thick films. In liquid (water), E follows an exponential decay for all films with a minimum soaked time t0 of 0.37 and 2.65 h for ultra-thin and thin and thick films, respectively. After this time, E saturates to a value in average 92 % smaller than that measured in air due to films swelling. Such results confirm the role of morphology envisaged in literature, suggesting also an additional role of mechanical properties in the antimicrobial activity.

Hafnium is a metal with rare properties, such as a low superconducting transition temperature slightly above 100 mK, which makes it attractive for a lot of applications, especially for design and fabrication of microcalorimeters with high energy resolution. In this paper we describe the results of fabrication and experimental investigation of superconducting properties of hafnium thin films in a dilution refrigerator. The considered Hf films, whose thickness is in the range from 60 to 115 nm, are deposited on substrates by electron beam evaporation. The combinations with thin layers of normal metals to decrease the critical temperature of superconducting hafnium films by proximity effect, are also considered. The critical temperature of the studied films varies from 56 to 302 mK. Also, significant increase of the critical temperature of some films over time was observed and investigated.

Magnetic and morphological properties of equiatomic B2-ordered FeRh thin films irradiated with single high-intensity ultrashort laser pulses are investigated. The goal is to elucidate the effect of femtosecond laser ablation on the magnetic properties of FeRh. We employed Scanning Magneto-Optical Kerr Effect (S-MOKE) microscopy to examine the magnetic phase after laser processing, providing high spatial resolution and sensitivity. Our results revealed the appearance of a magneto-optical signal from the bottom of ablation craters, suggesting a transition from antiferromagnetic to ferromagnetic behavior. Fluence-resolved measurements clearly demonstrate that the ablation threshold coincides with the threshold of the antiferromagnet-to-ferromagnet phase transition. The existence of such magnetic phase transition was independently confirmed by temperature-dependent S-MOKE measurements using a CW laser as a localized heat source. Whereas the initial FeRh film displayed a reversible antiferromagnet-ferromagnet phase transition, the laser-ablated structures exhibited irreversible changes in their magnetic properties. This comprehensive analysis revealed the strong correlation between the femtosecond laser ablation process and the magnetic phase transformation in FeRh thin films.

In this paper, fiber sensor based on Vernier effect for simultaneous measurement of relative humidity (RH) and temperature is proposed. The sensor is fabricated by coating two kinds of ultraviolet (UV) glue with different refractive indexes (RI) and thicknesses on the end face of a fiber patch cord. Vernier effect is formed by the inner lower-RI polymer cavity and the cavity composed of both polymer films. By calibrating the RH and temperature response of two peaks on the envelope of the reflection spectrum, simultaneous measurement of RH and temperature is realized by solving a set of quadratic equations. Experimental results show that the highest RH and temperature sensitivities of the sensor are 387.3 pm/%RH (in 20%RH to 90%RH) and -533.0 pm/°C (in 15°C to 40°C), respectively. The sensor has merits of low cost, simple fabrication, and high sensitivity, which makes it very attractive for applications that need to simultaneously monitor these two parameters.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

The product of ozonolysis, Glycero-(9,10-trioxolane)-trioleate (ozonide of oleic acid triglyceride, [OTOA]), was incorporated into polylactic acid/polycaprolactone (PLA/PCL) blend films in the amount of 1, 5, 10, 20, 30, and 40% w/w. The morphological, mechanical, thermal and antibacterial properties of the biodegradable blend after the OTOA addition were studied. According to DSC and XRD data, the crystallinity degree of PLA/PCL+OTOA films tended to decrease with increase in OTOA content that could be explained by its plasticizing effect. Morphological analysis showed that the structure of the films with the OTOA concentration above 20% drastically changed. Specifically, the interface between the PLA/PCL matrix and OTOA was formed, thereby forming a capsule with the embedded antibacterial agent. The moisture permeability of the resulting PLA/PCL+OTOA films decreased due to the formation of uniformly distributed hydrophobic amorphous zones that prevents water penetration. This architecture affects the tensile characteristics of the films: strength decreases to 5.6 MPa, elastic modulus E by 40%. The behavior of film elasticity is associated with the redistribution of amorphous regions in the matrix. Additionally, PLA/PCL+OTOA films with 20, 30 and 40% of OTOA showed good antibacterial properties on Pseudomonas aeruginosa, Raoultella terrigena (Klebsiella terrigena) and Agrobacterium tumefaciens. Developed PLA/PCL+OTOA films could be used as packaging materials and wound dressings. By variation of the OTOA content, it is possible to tailor the physical-chemical and antibacterial properties of the developed films for various applications.

The ability to simulate realistically the electronic structure of superconducting materials is important to understand and predict various properties emerging in both the superconducting topological and spintronics realms. We introduce a tight-binding implementation of the Bogoliubov-de Gennes method, parameterized from density functional theory, which we utilize to explore the bulk and thin films of Nb, known to host a significant superconducting gap. The latter is useful for various applications such as the exploration of trivial and topological in-gap states. Here, we focus on the simulations aspects of superconductivity and study the impact of temperature, Cooper-pair coupling and dimensionality on the size of the superconducting order parameter.

In this work, Al-Mo-B(CN) thin coatings were deposited by magnetron sputtering using composite metal-ceramic Al-Mo-B4C target. A metal-ceramic composite target for magnetron sputtering was fabricated by a robotic complex for detonation spraying of coatings equipped with a multi-chamber detonation accelerator. The powder composition (30Mo-30Al-40B4C) was sprayed onto the copper plate base of the composite target-cathode. The obtained cathode target with Al-Mo-B4C coating (thickness 280-300 μm) was used to deposit the Al-Mo-B(CN) coating (DC mode) on flat specimens of AISI 316 steels and silicon using equipment for magnetron sputtering UNICOAT 200. The Al-Mo-B4C coating has a lamella-type structure with inclusions of boron car-bide particles the elemental composition is evenly distributed in the material. The structure and morphology of coatings were studied using methods of optical, scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray analysis (XRD), and X-ray photoelectron spectros-copy (XPS). Mechanical and tribological properties of the Al-Mo-B(CN) thin coatings were determined using methods of nanoindentation, scratch testing, and tribological testing under fluid-free friction regime at room temperature. The Al-Mo-B(CN) coating (thickness ~ 1 μm) exhibited a dense uniform fine-grained structure with no columnar elements and were well-adherent to the substrates after deposition. Al-Mo-B(CN) coating has a amorphous structure. XPS analysis confirmed the formation of the MoB2 and AlN phase with an admixture of oxygen in the form of aluminum oxide, molybdenum oxide and boron oxide. Al-Mo-B(CN) coating possess hardness of 13 GPa, elasticity modulus of 114 GPa, elastic recovery of 45%, and friction coefficient of 0.8 against steel 100 Cr6 ball. The failure mode occurring in the tested coatings was fatigue and abrasive. The adhesion strength of Al-Mo-B(CN) coating amounted to about 11 N, and the failure mode was cohesive associated with plastic deformation and formation of fatigue cracks in the coating material.

Amorphous germanium films on non-refractory glass substrates were annealed by ultrashort near-infrared (1030 nm, 1.4 ps) and mid-infrared (1500 nm, 70 fs) laser pulses. Crystallization of germanium irradiated at a laser energy density (fluence) range from 25 to 400 mJ/cm2 under single-shot and multi-shot conditions was investigated using Raman spectroscopy. The dependence of the fraction of the crystalline phase on the fluence was obtained for picosecond and femtosecond laser annealings. The regimes of almost complete crystallization of germanium films over the entire thickness are obtained (from the analysis of Raman spectra with excitation of 785 nm laser). The possibility of scanning laser processing is shown, which can be used to create films of micro and nanocrystalline germanium on flexible substrates.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Mechanical robustness, biocompatibility, and antibacterial performances are key features for materials suitable to be used in tissue engineering applications. In this work, we investigated the link existing between structural and functional properties of TiCu(Ag) thin films deposited by physical vapor deposition magnetron sputtering on Si substrates. The thin films were characterized by X-ray diffraction (XRD), nanoindentation, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The TiCu(Ag) thin films showed complete amorphous structure and improved mechanical properties in comparison with pure Ti films. However, for contents in excess of 20% Ag, we observed the appearance of nanometric Ag crystallite. The TiCu(Ag) thin films displayed excellent biocompatibility properties, allowing adhesion and proliferation of the human fibroblasts MRC-5 cell line. Moreover, all the investigated TiCu(Ag) alloy display bactericidal properties, preventing the growth of both Pseudomonas aeruginosa and Staphylococcus aureus. Results obtained from biological tests have been correlated to the surface structure and microstructure of films. The excellent biocompatibility and bactericidal properties of these multifunctional thin films opens to their use in tissue engineering applications.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

This paper presents the results of the study of carbon films deposited on substrates of quartz, mica and silicon by the method of electron paramagnetic resonance (EPR). This study has identified the dependences of the intensities of the EPR signal, the g- factor, and the line width on the temperature of carbon films on various substrates with perpendicular and parallel arrangement of the sample plane relative to the orientation of the magnetic field are presented. The results of this study show that the dependence of the line width on temperature measurements does not change under both conditions for recording the EPR spectra. The research has also shown that with increasing temperature, the normalized intensity of the EPR signal line increases when carbon is deposited on various substrates (quartz, mica, and silicon) by the method of plasma decomposition of a mixture of CH4 and H2.

One of the important research directions in the field of photovoltaics is integration with construction. The integration of solar cell systems with a building can reduce installation costs and help optimize the used space. One of the interesting types of cells is dye-sensitized solar cells. In addition to their interesting properties, they also have aesthetic value. In the classic arrangement, they are constructed using glass with a transparent conductive layer (TCL). This article describes replacing a classic glass counter electrode with an electrode based on a ceramic tile and nickel foil. This solution makes it possible to expand their construction applications. The advantage of this solution is full integration with construction while simultaneously generating electricity. A dye-sensitized solar cell was built layer-by-layer on ceramic tile and nickel foil. An atomization method was used to deposit fluorine-doped tin oxide, and then a screen printing method was used to deposit a platinum layer. The electrical parameters of the manufactured DSSCs with and without a counter electrode tile were characterized by measuring their current-voltage characteristics under standard AM 1.5 radiation. A dye-sensitized solar cell integrated with ceramic tiles and nickel foil was produced and displayed an efficiency of over 4%.

In this paper, a novel biocompatible alloy defined as FeMoTaTiZr was obtained and functionalized by hydroxyapatite-based coatings (HAP) in order to increase their biocompatibility, bioactivity, and resistance to corrosion for to be used as bone implants. To obtain the surface with antibacterial properties, the HAP coatings were doped with small amount of Zn. The alloy was prepared using the VAR (Vacuum Arc Remelting) equipment, while the coatings by RF magnetron sputtering method. The EDS analysis confirmed the presence of Ca and P in the case of all developed coatings, having Ca/P or Ca/(P+Zn) ratio of about 1.70 and 1.66, respectively. The XRD and ATR-FTIR investigations confirmed the presence of calcium phosphate phases. The roughness of uncoated substrates increased after coating with HAP, and it was considerably increased by the Zn addition. The electrochemical tests showed that the un-doped HAP exhibited good corrosion behavior, while Zn doped HAP coatings have a high dissolution rate in fetal bovine serum, being more proper as a biodegradable material.

Three-dimensional porous nanostructures made of noble metals represent novel class of nanomaterials promising for nonlinear nanooptics and sensors. Such nanostructures are typically fabricated using either reproducible yet time-consuming and costly multi-step lithography protocols or less reproducible chemical synthesis that involve liquid processing with toxic compounds. Here, we combined scalable nanosecond-laser ablation with advanced engineering of the chemical composition of thin substrate-supported Au films to produce nanobumps containing multiple nanopores inside. Most of the nanopores hidden beneath the nanobump surface can be further uncapped using gentle etching of the nanobumps by an Ar-ion beam to form functional 3D plasmonic nanosponges. The nanopores 10-150~nm in diameter were found to appear via laser-induced explosive evaporation/boiling and coalescence of the randomly arranged nucleation sites formed by nitrogen-rich areas of the Au films. Density of the nanopores can be controlled by the amount of the nitrogen in the Au films regulated in the process of their magnetron sputtering assisted with nitrogen-containing discharge gas.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

Grazing incidence X-Ray Diffraction spectroscopy was employed to characterize crystallinity of Iron, Nickel, Copper and Tungsten, prepared by sparking discharge process in presence of 0.4 T magnetic field at ambient temperature 25 °C. Iron thin film preserved crystallinity even after one year of ageing. Nickel exhibit higher crystallinity when sparked in nitrogen gas flow from the one sparked in oxygen. Tungsten was successfully crystalized after just 40 minutes of sparking inside of magnetic field.

Three-dimensional nanocomposite networks consisting of percolated Si nanowires in a SiO₂ matrix, Si:SiO₂, were studied. The structures were obtained by reactive ion beam sputter deposition of SiO_x (x ≈ 0.6) thin films at 450 °C and subsequent crystallization using conventional oven as well as millisecond line focus laser annealing. Rutherford backscattering spectrometry, Raman spectroscopy, X-ray diffraction, cross-sectional and energy-filtered transmission electron microscopy were applied for sample characterization. While oven annealing resulted in a mean Si wire diameter of 10 nm and a crystallinity of 72 % within the Si volume, almost single-domain Si structures with 30 nm in diameter and almost free of amorphous Si were obtained by millisecond laser application. The structural differences are attributed to the different crystallization processes: Conventional oven tempering proceeds via solid state, millisecond laser application via liquid phase crystallization of Si. The 5 orders of magnitude larger diffusion constant in the liquid phase is responsible for the three times larger Si nanostructure diameter. In conclusion, laser annealing offers not only significantly shorter process times but moreover a superior structural order of nano-Si compared to conventional heating.

Hierarchical honeycomb patterns were manufactured with the breath-figures self-assembly by drop-casting on the silicone-oil lubricated glass substrates. Silicone oil promoted spreading of the polymer solutions. The process was carried out with the industrial grade polystyrene and polystyrene with the molecular weight Mw=35.000. Both of polymers gave rise to the patterns, built from micro- and nano-scaled pores. Ordering of the pores was quantified with the Voronoi tessellations and calculating the Voronoi entropy. Measurement of the apparent contact angles evidenced the Cassie - Baxter wetting regime of the porous films.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

Recent developments in mid-infrared (MIR) spectroscopic ellipsometry enabled by quantum cascade lasers (QCLs) resulted in a drastic improvement in signal-to-noise ratio compared to conventional thermal emitter based instrumentation. Thus, it was possible to reduce the acquisition time for high-resolution broadband ellipsometric spectra from multiple hours to less than 1 second. This opens up new possibilities for real-time in-situ ellipsometry in polymer processing. To highlight these evolving capabilities we demonstrate the benefits of a QCL based MIR ellipsometer by investigating single and multilayered polymer films. The molecular structure and reorientation of a 2.5m thin biaxially oriented polyethylene terephtalate film is monitored during a stretching process lasting 24.5 s to illustrate the perspective of ellipsometric measurements in dynamic processes. In addition, a polyethylene/ethylene vinyl alcohol/polyethylene multilayer film is investigated at continuously varying angle of incidence ( 0∘ – 50∘) in 17.2 s, highlighting an unprecedented sample throughput for the technique of varying angle spectroscopic ellipsometry in the MIR spectral range. The obtained results underline the superior spectral and temporal resolution of QCL ellipsometry and qualify this technique as suitable method for advanced in-situ monitoring in polymer processing.

Scintillators play a key role in the detection chain of several applications which rely on the use of ionizing radiation, and it is often mandatory to extract and detect the generated scintillation light as efficiently as possible. In positron emission tomography (PET), for example, both energy resolution and coincidence resolving time, two of the key detection parameters, depend strongly on the total amount of light which reaches the photodetector surface as well as its spatial and temporal distribution. Typical inorganic scintillators do however feature a high index of refraction, which impacts light extraction efficiency in a negative way. Furthermore, several applications such as preclinical PET rely on pixelated scintillators with small pitch. In this case, applying reflectors on the crystal pixel surface, as done conventionally, can have a dramatic impact of the packing fraction and thus the overall system sensitivity. This paper presents a study on light extraction techniques, as well as combinations thereof, for two of the most used inorganic scintillators (LYSO and BGO). Novel approaches, employing distributed Bragg reflectors (DBRs), metal coatings, and a modified Photonic Crystal (PhC) structure, are described in detail and compared with commonly used techniques. The nanostructure of the PhC is surrounded by a hybrid organic/inorganic silica sol-gel buffer layer which ensures robustness while maintaining its performance unchanged. We observed in particular a maximum light gain of about 41% on light extraction and 21% on energy resolution for BGO, a scintillator which has gained interest in the recent past due to its prompt Cherenkov component and lower cost.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Resveratrol is currently considered an option for chemoprevention and treatment of oral cancer, but the instability and unfavorable pharmacokinetics hinder its use in clinical practice. The present study deals with the preparation of resveratrol liposomes by a method that preserves stability and provides payload high enough for chemoprevention and/or treatment of oral cancer. Different temperatures, RSV concentrations and molar fractions, as well as the presence or absence of vitamin C in the hydration media were assayed. Liposome hydrodynamic diameter, polydispersity and zeta potential were evaluated by dynamic light scattering. In vitro biocompatibility, antioxidant activity and permeability were evaluated using TR146 cells and PermeaPad® membranes. Liposomes were included in hydrogels and films, and their suitability for buccal application was evaluated. According to the results, a temperature of 37ºC was optima to efficiently produce the resveratrol liposomes. Vitamin C was found to influence the liposome size, while resveratrol concentration significantly influenced the entrapment efficiency. High cell biocompatibility and potent intracellular antioxidant activity were observed and the inclusion of vitamin C reinforced the antioxidant effects. High permeation across PermeaPad® membranes and efficient uptake by TR146 cells was proved for resveratrol loaded liposomes. Liposomal hydrogels and films appropriated for buccal application were obtained and the payload of the formulations was high enough to produce mucosa concentrations above resveratrol IC50 values reported for cancer cells.

The integration of bacteriophages, a particular class of viruses that specifically infect bacteria and archaea, in biosensors for the monitoring of pathogens in foods and beverages is highly desirable. To this end, an increasing focus has been set on the exploration of covalent and physical methods for the immobilization of phages on solid surfaces. This work investigates the electrostatic assembly of tailed phages, specifically anti-Listeria monocytogenes P100 phages, on an ultrathin self-assembled monolayer (SAM) of 11-amino-1-undecanethiol (AUT). The cationic properties of AUT may allow for the electrostatic capture of P100 in a capsid-down fashion, thus, exposing the specific receptor-binding proteins on their tails to the corresponding pathogens in analytical samples. The physical properties of immobilized phages have been studied using AFM, SEM, and electrochemical techniques, providing insight into the orientation of the phages and revealing that the pH plays a remarkable role in the morphology and charge transfer behavior of the adsorbed films. Overall, this research portrays SAMs of amino-akylthiols as a valid platform for the oriented immobilization of bacteriophages on surfaces for electroanalytical purposes.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

Recently, Kayyalha et al. (Phys. Rev. Lett., 2019, 122, 047003) reported on anomalous enhancement of the self-field critical currents, I_c (sf,T), at low temperatures in Nb/BiSbTeSe₂-nanoribbon/Nb Josephson junctions. The enhancement was attributed to the low-energy Andreev bound states arising from winding of the electronic wave function around the circumference of the topological insulator BiSbTeSe₂ nanoribbon. In this paper, we show that identical enhancement in I_c(sf,T) and in the upper critical field, B_c2(T), at approximately same reduced temperatures, were reported by several research groups in atomically thin junctions based on a variety of Dirac-cone materials (DCM) earlier. Our analysis shows that in all these S/DCM/S systems the enhancement is due to a new superconducting band opening. Taking in account that several intrinsic superconductors also exhibit the effect of new superconducting band(s) opening when sample thickness becomes thinner than the out-of-plane coherence length, we strength our previous proposal that there is a new phenomenon of additional superconducting band(s) opening in atomically thin films.

Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study a novel technique has been used to simulta-neously improve the rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the pol-yimide matrix, resulted in enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid-modified-clay (SPNEAC) was successfully prepared and in-corporated into polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films show that the optical transparency of the SPNEAC-PI nanocomposite membranes de-creased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3 % was observed in the nanocomposite membrane containing 5wt.% modified clay at 500 nm wave-length, which is significantly lower than that for the neat PI membrane of about 36 %. The dispersion of SPNEAC containing high concentration of clay (≥ 40 wt.% clay), SPNEAC2 in polyimide matrix, resulted in attainment of a higher degree of imidization than was possible for the neat organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and polyaniline copolymer modified clay. The viscoelastic property of polyimide and the nanocomposite membranes was measured by using the dynamic mechanical spectroscopy, DMS. It was shown that the glass transition temperature, Tg of the nano-composites decreased, while the damping ability and impact energy increased with increasing weight fraction of fillers.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .