Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

In the last years, advances in materials engineering based on adaptive electronics have found a new paradigm to optimize drawbacks in signal processing. A two-layer MnO/ZnO:Zn heterostructure envisioned for frequency adaptive electronic signal processing is synthesized by sputtering where the use of internal states allows reconfigurability to obtain new operating modes at different frequency input signals. An X-Ray Diffraction (XRD) is performed on each layer, MnO:Mn had a cubic and ZnO:Zn a hexagonal structure with preferential growth in [111] and [002] directions respectively. It is determined that the coupling in this heterojunction is compatible with a mismatch less 1 % due texture in each layer which implies a low number of defects. An electrical characterisation with an oscilloscope and signal generator was carried out to obtain the time-response signals and current-voltage (I-V) curves where no degradation is detected when changing from a range of frequencies (100 Hz – 1 MHz). An equivalent circuit is proposed to explain the effects in the interface. Finally, the MnO/ZnO:Zn heterojunction delivers states that are stable, repeatable, and reproducible and it demonstrates how the interaction of the materials can be used in adaptive device applications applying frequencies and internal states as to create new and innovative design schematics, reducing the numbers of components/connections in a system for future sustainable electronics.

We fabricate paper-supported semiconducting devices by rubbing a layered molybdenum disulfide (MoS₂) crystal onto a piece of paper, similarly to the action of drawing/writing with a pencil on paper. We show that the abrasion between the MoS₂ crystal and the paper substrate efficiently exfoliates the crystals, breaking the weak van der Waals interlayer bonds and leading to the deposition of a film of interconnected MoS₂ platelets. Employing this simple method, that can be easily extended to other 2D materials, we fabricate MoS₂-on-paper broadband photodectectors with spectral sensitivity from the ultraviolet (UV) to the near-infrared (NIR). We also used these paper-based photodetectors to acquire pictures of objects by mounting the photodetectors in a homebuilt single-pixel camera setup.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and conditions, we identify the condition that the coating speed should equal the growth speed of the fastest growing crystal plane as crucial for achieving a high degree of directional crystallization.

The paper considers new effects of the nanoscale state of matter, which open up prospects for the creation of electronic devices using new physical principles. The contact of chemically homogeneous different sizes hydrated nanoparticles of yttrium-stabilized zirconium oxide (ZrO2 – x %mol Y2O3, x=0, 3, 4, 8; YSZ) with particle sizes of 7.5 nm and 7,5 nm; 7.5 nm and 9 nm; 7.5 nm and 11 nm; 7.5 nm and 14 nm in the form of compacts obtained using high hydrostatic pressure (HP-compacts of 300MPa) was studied at direct and alternating current. A unique size effect of the nonlinear (semiconductor) dependence of the electrical properties (in the region U <2.5 V, I ≤ 2.7 mA) of the contact of different-sized YSZ nanoparticles of the same chemical composition is revealed, which indicates the possibility of creating semiconductor structures of a new type based on chemically homogeneous nanostructured systems. The electronic structure of the near-surface regions of nanoparticles of a special type of oxide materials and the possibility, on this basis, to obtain specifically rectifying properties of the contacts were studied theoretically. Models of surface states of the Tamm type are constructed, but considering the Coulomb long-range action. The discovered variance and its dependence on the curvature of the surface of nanoparticles made it possible to study the conditions for the formation of a contact potential difference in cases of nanoparticles of the same radius (synergistic effect), different radii (doped and undoped variants), as well as to discover the possibility of describing a group of powder particles from material within the Anderson model. The established effect makes it possible to solve the problem of diffusion instability of semiconductor heterojunctions and opens up prospects for creating electronics devices with a fundamentally new level of properties for use in various fields of the national economy and breakthrough critical technologies.

In this article we present the design and development of T-Shirt prototypes that embed novel textile sensors for the capture of cardio and respiratory signals. The sensors are connected through textile interconnects to either an embedded custom designed data acquisition and transmission unit or to snap fastener terminals for connection to external monitoring devices. Prototypes with diverse approaches of integration are presented. The performance of the wearable systems is addressed in terms of signal-to-noise ratio amplitude and signal interference caused by baseline wander and motion artifacts, through laboratorial tests with subjects in standing and walking conditions. Performance tests were also conducted in Hospital environment using a T-Shirt prototype connected to a commercial 3-channel Holter monitoring device. The textile sensors and interconnects were realized with the assistance of an industrial 6-needle digital embroidery tool and their resistance to wear addressed with normalized tests of laundering and abrasion. The main aspects of the system´s design leading to major improvements and failure factors are discussed. Pathways and methods for the overall system´s optimization are highlighted.

AbstractWhile the technology is relatively new, low cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use and availability of 3D design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties providing platforms for a huge number of strategies that can be chosen for user’s needs. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating development of low cost, sensitive and often geometrically complex tools. 3D printing in fabrication of microfluidics, supporting equipment, optical and electronic components of diagnostic devices is presented. Emerging diagnostic 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also discussed.

Conductive hydrogels combine the properties of both hydrogels and electrical conductivity, making them soft, flexible, and biocompatible. These properties enable them to conform to irregular surfaces, stretch and bend without losing their electrical conductivity, and interface with biological systems. Conductive hydrogels can be utilized as conductive traces, electrodes, or as a matrix for flexible electronics. Exciting applications in sensors, tissue engineering and human-machine interaction have been demonstrated worldwide. This review comprehensively covers the progress in this field, focusing on several main aspects: functional materials, performance improvement strategies, and wearable applications in human-related areas. Furthermore, the major approaches and challenges for improving their mechanical properties, conductivity, and long-term stability are systematically summarized.

The construction enterprise is a essential zone that contributes considerably to the worldwide financial system. but it faces numerous challenges, together with inefficiency in electric and electronics engineering tasks. This inefficiency results in delays, expanded charges, and decreased productivity. Device learning strategies have the capacity to deal with those challenges through optimizing the making plans and execution of electrical and electronics engineering tasks within the construction industry. This study paper targets to discover using machines gaining knowledge of strategies to maximise efficiency in electrical and electronics engineering projects inside the production industry. Mainly, the paper will be conscious of developing and imposing gadget mastering algorithms to optimize project scheduling, fabric procurement, and system utilization. The paper will even look at the ability of using predictive analytics to identify and mitigate dangers related to electric and electronics engineering tasks. The study could be based on a combination of literature review and empirical analysis. The literature evaluation will provide a top-level view of the demanding situations going through the development industry and the capability advantages of the usage of system getting to know strategies to deal with those challenges. The empirical evaluation will involve the improvement and testing of device mastering models on real-world information from electrical and electronics engineering initiatives inside the construction industry. The predicted results of this research are the development of a fixed of sensible recommendations for the use of machine gaining knowledge of strategies to optimize electric and electronics engineering projects within the construction industry. These suggestions will be beneficial for venture managers, engineers, and other stakeholders within the creation enterprise who're inquisitive about maximizing performance and decreasing charges of their tasks. Ordinary, this studies paper aims to contribute to the continued efforts to enhance the efficiency and productiveness of the development enterprise via exploring the ability of system studying techniques to optimize electrical and electronics engineering tasks.

The attributes of electroplating as a low-cost, simple, scalable and manufacturable semiconductor deposition technique for the fabrication of large-area and nanotechnology-based device applications are discussed. These strengths of electrodeposition are buttressed experimentally using techniques such as X-ray diffraction, Ultraviolet-visible spectroscopy, Scanning electron microscopy, Atomic force microscopy, Energy-dispersive X-ray spectroscopy and photoelectrochemical cell studies. Based on the structural, morphological, compositional optical, and electronic properties evaluated results, it is evident that electroplating possesses the capabilities of producing high-quality semiconductors usable in producing excellent devices. In this paper, we will describe the progress of electroplating technique mainly for the deposition of semiconductor thin film materials, their treatment processes and fabrication of solar cells.

Barriers to inventing electronic devices involve challenges of iterating electronic designs due to long lead times for professional circuit board milling or high-costs of commercial milling machines. To overcome these barriers this study provides open source (OS) designs for a low-cost circuit milling machine. First, design modifications for mechanical and electrical sub-systems of the OS D3D Robotics prototyping system are provided. Next, Copper Carve, an OS custom graphical user interface, is developed to enable circuit board milling by implementing backlash and substrate distortion compensation. The performance of the OS D3D circuit mill is then quantified and validated for: positional accuracy, cut quality, feature accuracy and distortion compensation. Finally, the return on investment is calculated for inventors using it. The results show by properly compensating for motion inaccuracies with Copper Carve, the machine achieves a motion resolution of 10 microns, which is more than adequate for most circuit designs. The mill is at least five times less expensive than all commercial alternatives and the material costs of the D3D mill are repaid from fabricating 20-43 boards. The results show that the OS circuit mill is of high-enough quality to enable rapid invention and distributed manufacturing of complex products containing custom electronics.

In the present work, cost-effective strain gauges were fabricated by using inkjet printing and photonic curing on flexible and recyclable PET substrates. Ohmic resistance (a.k.a. DC resistance) (R0) and complex electrical impedance (Z) as a function of test frequency were characterized, respectively, with the state-of-the-art electronic testing equipments. For the fabrication process, commercially available silver nanoparticle (AgNP) inks and printing substrates were used in order to eliminate any apriori ink processing. In order to validate the in-house cantilever beam measurement setup and devices, first, commercially available metallic foil strain gauges (with the provided gauge factor GF=2 by the manufacturer) were tested at different locations. Thereafter, the printed strain gauges were investigated with several repetitions at different measurement locations. The measurement results demonstrated an affordable, rapid and tailorable design and repeatable fabrication approach for strain gauges with GFavg~6.6, which has potential applications in remote sensing and structural monitoring applications.

Soil conditions is a major aspect of interest for farmers due to the knowing of the physicochemical properties of the same can help with any necessary restoration of soil that guarantees the quality and the production of their crop. However, technology and analysis of the soil become of difficult access mainly in developing countries, by which the present paper shows the development of a system thought to estimate physicochemical variables of soils growing sugar cane through studies of spectroscopy. Its characteristic is that it is a portable system, with low cost, easy to use and can estimate physicochemical variables in-situ with the objective of knowing the degree of degradation present in the soil and through this help the farmers define possible strategies to restore it. The device uses the frequency response of the soil determining values of magnitude and phase, which are used by algorithms of artificial intelligence capable of getting an estimation of the physicochemical properties. The obtained results show errors below 8% in the estimation of the variables compared to the analysis results of the soil at laboratories.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

The protection of electronics against environmental influences and mechanical loads is important for integration of conventional electronics in textile conductive tapes. For this purpose, the sensors on the tapes are molded with plastic locally. This process step is recognized in the injection molding process. The molding compound is then later selected depending on: The field of application, the parameters of the manufacturing process and the textile tape properties. We have designed a mould for liquid silicone (LSR) as well as for the textile and electronic insertions. The cavities are sealed by a local compression of the textile and the two inserts are positioned with position pins representing the main aspect of the mould design. The sampling tool and the process parameter optimization are mainly based on the material properties of the silicone and the mechanical sensitivity of the inserts. To reduce the deformation of the circuit boards by the melt front and ensuring the functionality of the electronics a low-pressure process is used.

Polymer composites with high thermal conductivity have a great potential for applications in modern electronics due to their low cost, easy process, and stable physical and chemical properties. Nevertheless, most polymer composites commonly possess unsatisfactory thermal conductivity, primarily because of the high interfacial thermal resistance between inorganic fillers. Herein, we developed a novel method through silver functionalized graphene nanosheets (GNS) and multiwalled carbon nanotube (MWCNT) composites with excellent thermal properties to meet the requirements of thermal management. The effects of composites on interfacial structure and properties of the composites were identified, and the microstructures and properties of the composites were studied as a function of the volume fraction of fillers. An ultrahigh thermal conductivity of 12.3 W/mK for polymer matrix composites was obtained, which is an approximate enhancement of 69.1 times compared to the polyvinyl alcohol (PVA) matrix. Moreover, these composites showed more competitive thermal conductivities compared to untreated fillers/PVA composites applied to the desktop central processing unit, making these composites a high-performance alternative to be used for thermal management.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

Chemical versatility of organic semiconductors provides nearly unlimited opportunities for tuning their electronic properties. However, despite decades of research, relationship between molecular structure, molecular packing and charge mobility in these materials remains poorly understood. This reduces the search for high-mobility organic semiconductors to the inefficient trial-and-error approach. For clarifying the abovementioned relationship, investigations of the effect of small changes in the chemical structure on OSs properties are particularly important. In this study, we address computationally the impact of substitution of C-H atom pairs by nitrogen atoms (N-substitution) on molecular properties, molecular packing and charge mobility of crystalline oligoacenes. Besides of decreasing frontier molecular orbital levels, N-substitution dramatically alters molecular electrostatic potential yielding pronounced electron-rich and electron-deficient areas. These changes in the molecular electrostatic potential strengthen face-to-face and edge-to-edge interactions in the corresponding crystals and result in the crossover from the herringbone packing motif to π-stacking. When the electron-rich and electron-deficient areas are large, sharply defined and, probably, have certain symmetry, charge mobility increases up to 3-4 cm2V-1s-1. The results obtained highlight the potential of azaacenes for application in organic electronic devices and are expected to facilitate rational design of organic semiconductors for steady improvement of organic electronics.

Electronic designers nowadays are facing two challenging demands for various applications: miniaturization and increased functionality. To satisfy these seemingly opposed requirements, reducing the number of mounted components—and thus solder joints—in PCB designs becomes an attractive approach by directly printing passive components such as embedded resistors into the circuit. This approach can also potentially increase the reliability, such as “mean time between failures” (MTBF), while reducing the circuit board size. With its unique capabilities for non-contact precision material deposition, the Aerosol Jet® direct-write technology has been enabling additive manufacturing of fine-feature electronics conformally onto flexible substrates of complicated shapes. The CAD/CAM controlled relative motions between substrate and print head allows convenient adjustment of the pattern and pile height of deposited material at a given ink volumetric deposition rate. To date in the printed electronics industry, additively printing embedded polymer-thick-film (PTF) resistors has mostly been done with screen printing using carbon-based paste inks. Here we demonstrate results of Aerosol Jet® printed PTF resistors of resistance values ranging from ~50 W to > 1 kW, adjustable (among several variable parameters) by the number of stacked layers (or print passes with each pass depositing a fixed amount of ink) between contact pads of around 1 mm apart with footprint line typically < 0.3 mm. In principle, any ink material that can be atomized into fine droplets of 1 to 5 microns can be printed with the Aerosol Jet® system. However, the print quality such as line edge cleanliness can significantly influenced by ink rheology which involves solvent volatility, solids loading, and so on. Our atomizable carbon ink was made by simply diluting a screen printing paste with a compatible solvent of reasonable volatility, which can be cured at temperatures below 200 ^oC. We show that Aerosol Jet® printed overlapping lines can be stacked to large pile height (to reduce the resistance value) without significant increase of line width, which enables fabricating embedded resistors with adjustable resistance values in a limited footprint space.

Spatially uniform optical excitations can induce Floquet topological band structures within insulators which can develop similar or equal characteristics as are known from three-dimensional topological insulators. We derive in this article theoretically the development of Floquet topological quantum states for electromagnetically driven semiconductor bulk matter and we present results for the lifetime of these states and their occupation in the non-equilibrium. The direct physical impact of the mathematical precision of the Floquet-Keldysh theory is evident when we solve the driven system of a generalized Hubbard model with our framework of dynamical mean field theory (DMFT) in the non-equilibrium for a case of ZnO. The physical consequences of the topological non-equilibrium effects in our results for correlated systems are explained with their impact on optoelectronic applications.

The development of organic devices has been focused in their miniaturization in order to obtain denser and faster electronic circuits. The challenge is to build the devices adding atom by atom or molecule by molecule until the desired structure is achieved. To do this job, techniques able to see and manipulate matter at this scale are needed. Scanning tunneling microscopy has been the selected technique by scientists to develop smart and functional unimolecular devices. This review article compiles the latest developments in this field giving examples of supramolecular systems monitored and fabricated at molecular scale by bottom-up approaches using STM at solid/liquid interface.

Multiple valued logic (MVL) has proven to be a better alternative and solution to the challenges of traditional binary logic because of its fast computation, fewer interconnects, and small die. It is a potential candidate for future digital design because it allows energy-efficient, low-complex, and high-speed circuits. This paper introduces a new resistive-load two-dimensional field effect transistor-based ternary logic gates, wherein the active resistive-load is replaced with memristor to reduce chip area and power consumption. A memristor-based standard ternary inverter (STI) is designed using GNRFET, MoS2 FET, WSe2 FET, and FinFET, and their performance metric such as delay, power, and energy delay product (EDP) are analyzed. The results show that the proposed design achieves 50% reduction in circuit area, the average power dissipation is reduced by 11.7X, 6.8X, and 3.2X for GNRFET, MoS2 FET, and WSe2 FET, respectively, as compared to FinFET-based ternary inverter. Moreso, other logic gates such as OR, NOR, AND and NAND were simulated in T-SPICE EDA tool, and the results and truth table are in good agreement.

Efficient natural convection-cooled heat sinks are vital to the future of electronics cooling due to their low energy demand in the absence of an external pumping agency in comparison to other cooling methods. The present study is aimed to identify the most effective fin design for enhancing heat transfer in natural convection applications. Initially, a baseline case with rectangular fins was considered in the present study and it was optimized with respect to fin spacing. This optimized baseline case is then validated against the semi-empirical correlation proposed by Elen-baas (1942) [2]. Upon good agreement, the validated model is used for comparative analysis of different heat sink configurations with rectangular, trapezoidal, curved, and angled fins. The optimised fin spacing obtained for the baseline case is also used for the other heat sink configura-tions and then the fin designs are further optimized for better performance. However, for the an-gled fin case, the optimized configuration proposed by Zhang et al. (2020) [3] is adopted in the present study. This study is carried out with Ansys Fluent for a Rayleigh number of 2.4 × 10^6. The proposed novel curved fin design with a shroud defined as Case C4 showed a 4.1% decrease in the system’s thermal resistance with an increase in the heat transfer coefficient of 4.4% when compared to the optimized baseline fin case. The obtained results are further non-dimensionalized with proposed scaling in terms of the baseline case for the two novel heat sink cases (trapezoidal, curved).

Printed electronic devices are attracting significant interest due to their versatility and low cost; however, quality control during manufacturing is a significant challenge, preventing the widespread adoption of this promising technology. We show that terahertz (THz) radiation can be used for the in situ inspection of printed electronic devices, as confirmed through a comparison with conventional electrical conductivity methods. Our in situ method consists of printing a simple test pattern exhibiting a distinct signature in the THz range that enables the precise characterization of {the static} electrical conductivities of the printed ink. We demonstrate that contactless dual-wavelength THz spectroscopy analysis, which requires only a single THz measurement, is more precise and repeatable than the conventional four-point probe conductivity measurement method. Our results open the door to a simple strategy for performing contactless quality control in real time of printed electronic devices at any stage of its production line.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

In this study, we investigate the structural changes, electronic properties, and charge redistribution within azo-bithiophene (Azo-BT) chemisorbed monolayers under different light stimuli using density functional theory and molecular dynamics simulations. We consider two types of switches, Azo-BT and BT-Azo, with different arrangements of the Azo and BT blocks counting from the anchor thiol group. The chemisorbed monolayers of pure cis- and trans-isomers with a surface concentration of approximately 2.7 molecules per nm2 are modeled on a gold surface using classical all-atom molecular dynamics. Our results reveal significant shrinkage of the BT-Azo layer under UV illumination, whereas the thicknesses of the Azo-BT layer remain comparable for both isomers. This difference in behavior is attributed to the ordering of the trans-molecules in the layers, which is more pronounced for Azo-BT, leading to a narrow distribution of the inclination angle to the gold surface. Conversely, both layers consisting of cis-switches exhibit disorder, resulting in similar brush heights. To study charge transfer within the immobilized layers, we analyze each snapshot of the layer and calculate mean charge transfer integrals using Nelsen’s algorithm for a number of interacting neighboring molecules. Combining these integrals with reorganization energies defined for the isolated molecules, we evaluate the charge transfer rates and mobilities for electron and hole hopping within the layers at room temperature based on Marcus’ theory. This research offers new perspectives for the innovative design of electrode surface modifications and provides insights into controlling charge transfer within immobilized layers using light triggers. Additionally, we identify molecular properties that are enhanced through specific molecular design, which contributes to the development of more efficient molecular switches for various electronic applications.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

In this study, we introduce the concept and construction of an innovative Digital Miniature Cathode Ray Magnetometer designed for the precise detection of magnetic fields. This device addresses several limitations inherent to magnetic probes such as D.C. offset, nonlinearity, temperature drift, sensor aging, and the need for frequent recalibration, while capable of oper-ating in a wide range of magnetic fields. The core principle of this device involves the utilization of a charged particle beam as the sensitivity medium. The system leverages the interaction of an electron beam with a scintillator material, which, then, emits visible light that is captured by an imager. The emitted scintillation light is captured by a CMOS sensor. This sensor not only rec-ords the scintillation light but also accurately determines the position of the electron beam, providing invaluable spatial information crucial for magnetic field mapping. The key innova-tion lies in the combination of electron beam projection, CMOS imager scintillation-based de-tection and digital image signal processing. By employing this synergy, the magnetometer achieves remarkable accuracy, sensitivity and dynamic range. The precise position registration enabled by the CMOS sensor further enhances the device's utility in capturing complex magnetic field patterns, allowing for 2D field mapping. In this work, the optimization of the probe's per-formance is tailored for applications related to the characterization of insertion devices in light sources, including undulators.

Innovations in industrial automation, information and communication technology (ICT), renewable energy, monitoring and sensing fields have been paving the way for smart devices, which can acquire and convey information to the internet, in every aspect of our lives. Since there is ever-increasing demand for large yet affordable production volumes for such devices, printed electronics has been attracting great attention in both industrial and academic research. In order to understand the potential and future prospects of the printed electronics, the present paper summarizes the basic principles and conventional approaches while providing the recent progresses in the fabrication and material technologies, applications and environmental impacts.

The work presents a Structural Health Monitoring (SHM) electronic system with real-time ac-quisition and processing for the determination of impact location in laminates. The novelty of this work is the quantitative evaluation of impact location errors using the Lamb wave guided mode S0, captured and processed in real-time by up to eight piezoelectric sensors. The differential time of arrival is used to minimize an error function for the position estimation. The impact energy is correlated to the amplitudes of the antisymmetric (A0 ) mode and the electronic design is de-scribed to avoid saturation for signal acquisition. The same electronic is designed to acquire symmetric (S0 ) low level signals by adequate gain, bandwidth and signal to noise ration. Such signals propagate into a 1.4mm thick aluminum laminate at the group velocity of 5150m/s with frequency frequency components above 270kHz and can be discriminated from the A0 mode to calculate accurately the differential arrival time. The results show that the error is not improved better than S0 wavelength in impact localization by using six out of eight sensors connected to the electronic system.

Penetration of grid connected inverters (GCI) has arisen in power systems due to increasing integration of renewable sources. However, restrictive grid codes require that renewable sources connected to the grid with power electronic systems must be properly connected and appropriate currents must be injected to support stability of the grid under grid faults. Simultaneous injection of symmetrical positive and negative sequence currents is mandatory to support stabilization of grid at the instant of grid faults. Conventional synchronously rotating frame dq current controllers are insufficient under grid faults due to low bandwidth of PI controllers. This paper proposes a new grid current control strategy for grid connected voltage source inverters under unbalanced grid voltage conditions. A proportional current controller with a first order low pass filter disturbance observer (DOb) is proposed which establishes positive sequence power requirements and independently control negative sequence current components under unbalanced voltage conditions. The method does not need any parameter, since it estimates nonlinear terms with low pass filter DOb. Simulations are implemented in Matlab/Simulink platform demonstrating the effectiveness of proposed method.

Industrial pilot projects often rely on proprietary and expensive electronic hardware to control and monitor experiments. This raises costs and retards innovation. Open-source hardware tools exist for implementing these processes individually, however, they are not easily integrated with other designs. The Broadly Reconfigurable and Expandable Automation Device (BREAD) framework provides many open-source devices which can be connected to create more complex data acquisition and control systems. This article explores the feasibility of using BREAD plug-and-play open hardware to quickly design and test monitoring and control electronics for an industrial materials processing prototype pyrolysis reactor. Generally, pilot-scale pyrolysis plants are expensive custom designed systems. The plug-and-play prototype approach is first tested by connecting it to the pyrolysis reactor and ensuring it can measure temperature and actuate heaters and a stirring motor. Next, a single circuit board system was created and tested using the designs from the BREAD prototype to reduce the number of microcontrollers required. Both open-source control systems were capable of reliably running the pyrolysis reactor continuously and the overall cost of control was reduced by more than 10X. Open-source, plug-and-play hardware provides a reliable avenue for researchers to quickly develop data acquisition and control electronics for industrial-scale experiments.

Optical rotatory dispersion (ORD) is a beautiful analytical technique for the study of chiral molecules and polymers. In this study, ORD was applied successfully to follow the degree of polycondensation of l-(+)-lactic acid toward the formation of poly(lactic acid) oligomers (PLAO) and high molecular weight poly(l-lactic acid) (PLLA) in a simple esterification reaction equipment. PLLA is a biodegradable polymer obtainable from renewable raw materials. The racemization of the intrinsically isotactic PLLA through thermal treatment can be easily followed through the use of ORD spectroscopy. Organic or molecular electronics is a hot topic dealing with the combination of π-conjugated organic compounds and polymers with specific properties (e.g. chirality) which can be exploited to construct optoelectronic devices such as organic light-emitting diodes (OLEDs), organic photovoltaic (OPV) high efficiency cells, switchable chirality devices, organic field-effect transistors (OFETs), and so on. ORD spectroscopy was applied to study either the gigantic optical rotation of PLLA films as well as to detect successfully the excitonic coupling occurring in thin solid PLLA green film loaded with a combination of two dyes: SY96 (a pyrazolone dye) and PB16 (the metal-free phthalocyanine pigment). The latter compound PLLA loaded with SY96 and PB16 shows a really gigantic optical activity in addition to typical ORD signal due to exciton coupling and may be considered as a simple and easily accessible model composite of a chiral polymer matrix combined with π-conjugated dyes for molecular electronics studies.

The growing adoption of electric propulsion systems in Maritime Autonomous Surface Ships (MASS) necessitates advancements in shipboard electronics for safe, efficient, and reliable operation. These advancements are crucial for tasks like real-time sensor data processing, control algorithms for autonomous navigation, and robust decision-making capabilities. This study investigates research trends in MASS using bibliographic analysis to inform policy and future research directions in this evolving field. We analyze 3,363 MASS-related articles from the Web of Science database, employing co-occurrence word analysis and latent Dirichlet allocation (LDA) topic modeling. Findings reveal a rapidly growing field dominated by image recognition research. Keywords like "datum," "image," and "detection" suggest a focus on collecting and analyzing marine data, particularly with deep learning for synthetic aperture radar imagery. LDA confirms this, with "Image analysis and classification research" as the leading topic. The study also identifies national and organizational leaders in MASS research. However, research on Arctic routes lags behind other areas. This work provides valuable insights for policymakers and researchers, promoting a deeper understanding of MASS and informing future policy and research agendas for the integration of electric propulsion systems in the maritime industry.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Nowadays there is a need to increase the density of interconnections on printed circuit boards (PCBs). Does this mean that the only way out for quality PCB manufacturing is to proportional increase in precision of equipment, or is there another way? One of the main constraints to increasing the density of PCB interconnections is the transition holes. As the number of conductive layers increases, the number of vias increases and they cover a significant space on the PCB. On the other hand, reducing the size of the vias is limited by the capability of spatial alignment of the PCB stack during manufacturing. There are standards that set limits for the design of contact pads on a PCB (IPC-A-600G, IPC-6012B). However, depending on the precision of production, the contact pads may be of poor quality. This raises the issue of determining the reliability of a contact pad with defined parameters at the design stage, taking into account manufacturing capabilities. This research proposes an analytical method for evaluation of reliability of a via or plated through-hole based on calculation of its probability of production in accordance with the current standards. On the basis of the method a model was developed both for the case of a contact pad without any conductors connected to it (nonfunctional contact pad) and for the real case with a connected conductor. The model estimates the probability of making an acceptable via for a given reliability class depending on parameters such as the conductor width (minimum permissible and usable), drilled hole diameter and pad diameter, as well as the accuracy of the drilling operation. The analysis of the modeling results showed that for the real case, a reduction in the reliability class would insignificantly affect the probability of making an acceptable via due to the tight limitation on the connection place of the conductor and the contact pad. In conclusion, we propose an algorithm for determining the optimal parameters of teardrops to minimize the negative impact of the conductor on the reliability of the vias.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

Under the main features required on portable devices in electrochemical instrumentation is to have a small size, low power consumption, economically affordable, and precision in the measurements. This paper describes the development of a programmable Embedded Potentiostat System (EPS) capable of performing electrochemical sensing over system-on-a-chip platforms. Furthermore, the study explains a circuit design and develops some validation of the entire system. The hardware validation is performed by electrochemical experiments such as Double Step Chronoamperometry (DSC), Linear Sweep Voltammetry (LSV) and Cyclic Voltammetry (CV); moreover, a comparison of the experimental signals between a commercial potentiostat and the EPS was done by analysis of errors on the response signal. Results illustrate that the EPS is capable of handling currents in the range of absolute values of 86.44 to 3000 nA, and having control voltages in the range of ± 2 V. The device can support from 50 to 2000 samples per second. The EPS capabilities were compared with other compact potentiostats. The programmable EPS is an original approach which hugely reduces the hardware complexity and leads the way to create new applications for Point-of-Care or industrial developments with a reusable full electronics module.

A variational analysis of dispersion medium (electrolytes and surfactants) was carried out for the best nucleotide interactions with the presence of nanoparticles and the ability to formation of homogeneous coatings upon drying / lyophilization. Using UV-spectroscopy and transmission electron microscopy, the processes of immobilization of nucleotides on the surface of nanoparti-cles of the composition ZrO2-3mol% Y2O3 (YSZ) in the presence of various dispersing agents were investigated. Promising dispersing agents were established, the optimal composition of suspen-sions based on DNA nucleotides and YSZ nanoparticles, which is potentially suitable for adaptive technologies of bionanoelectronics, was selected. The aim of the work is to obtain and study functional media for molecular electronics based on heterojunctions biological molecule – wide-gap dielectric.

A variational analysis of dispersion medium (electrolytes and surfactants) was carried out for the best nucleotide interactions with the presence of nanoparticles and the ability to formation of homogeneous coatings upon drying / lyophilization. Using UV-spectroscopy and transmission electron microscopy, the processes of immobilization of nucleotides on the surface of nanoparti-cles of the composition ZrO2-3mol% Y2O3 (YSZ) in the presence of various dispersing agents were investigated. Promising dispersing agents were established, the optimal composition of suspen-sions based on DNA nucleotides and YSZ nanoparticles, which is potentially suitable for adaptive technologies of bionanoelectronics, was selected. The aim of the work is to obtain and study functional media for molecular electronics based on heterojunctions biological molecule – wide-gap dielectric.