This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

This review is devoted to present the history of CARDIOSIM© software simulator platform, which was developed in Italy to simulate the human cardiovascular and respiratory system. The first version of CARDIOSIM© was developed at the Institute of Biomedical Technologies of the National Research Council in Rome. The first platform version published in 1991 ran on PC with disk operating system (MS-DOS) and was developed using the Turbo Basic language. The last version runs on PC with Microsoft Windows 10 operating system; it is implemented in Visual Basic and C++ languages. The platform has a modular structure consisting of seven different general sections, which can be assembled to reproduce different pathophysiological conditions. The software simulator can reproduce the most important circulatory phenomena in terms of pressure and volume relationships. It represents the whole circulation using a lumped-parameter model and enables the simulation of different cardiovascular conditions according to Starling’s law of the heart and a modified time-varying elastance model. Different mechanical ventilatory and circulatory devices have been implemented in the platform including thoracic artificial lung, ECMO, IABP, pulsatile and continuous right and left ventricular assist devices, biventricular pacemaker and biventricular assist devices. CARDIOSIM© is used in clinical and educational environment.

Solid waste management is a challenge in many countries, especially developing economies. The author identified nine major waste issues reported during the current pandemic period. The impacts of the pandemic continue to be felt and have indicated secondary impacts with respect the waste management. The reflective topics highlighted in the present article are not intended to be exhaustive. Still, they give us a starting point for reflecting on how we can construct a more resilient waste management system.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

Background and Objectives: The site types of Eucalyptus urophylla × Eucalyptus grandis clonal plantations in southern Yunnan were compared, aiming to provide basis for site selection and scientific plantations management. Materials and Methods: In this study, 80 standard plots were set up in the 6−9-year-old Eucalypts plantations in Pu'er City and Lincang City. Furthermore, the quantitative theory I model and canonical correlation analysis were used to analyze the relationship between dominant tree growth traits and site factors, and evaluate the growth potential of E. urophylla × E. grandis plantation. Results: The multiple correlation coefficient between 8 site factors (altitude, slope, slope level, soil thickness, slope direction, texture, soil bulk density, and litter thickness) and the quantitative growth of the dominant wood was 0.825 (P < 0.05). According to the correlation coefficient of the quantitative regression model, slope, altitude, and soil thickness were the main factors for the classification of E. urophylla × E. grandis plantations in southern Yunnan. In addition, E. urophylla × E. grandis plantations grew best downhill and mid uphill at relatively low altitude, where the soil layer was thick and composed of weathered red soil. Contrastingly, E. urophylla × E. grandis plantation growth was extremely poor in uphill sites at higher altitude, where the soil layer was thin and composed of semi-weathered purple soil. Furthermore, total N, and available B, Cu, and Zn content, as well as soil organic matter content in the soil had a great influence on the growth of E. urophylla × E. grandis. Conclusions: Nitrogen and phosphate fertilizer as well as trace elements such as B, Zn, and Cu can be properly applied in middle- and low-yield forests to promote the growth and development of E. urophylla × E. grandis plantations.

Background: Electronic cigarette (e-cigarette) use among youth in Poland has become very popular. The aim of this study was to identify potential points of access to these products among students aged 16-17 before implementation of sales restrictions to minors in Poland in November 2016. Methods: A school-based, cross-sectional survey was administered in 2015-2016 in 21 secondary/technical schools across two regions of Poland. Analyses focused on 341 students aged 16-17 who reported past 30-day use of e-cigarettes. Pearson chi-square analyses were utilized to examine associations between access-related items, e-cigarette use, and demographics. Results: Among youth e-cigarette users, the most common access to their first e-cigarette was from a friend (38%), followed by purchasing from vape shops (26%). Similar patterns emerged when students were asked about the access to their currently used e-cigarette. Most youth reported no difficulty purchasing cartridges/e-liquid containing nicotine (90%); the majority of users (52%) reported buying such products in vape shops. Conclusions: Prior to implementing age-related sales restrictions, youth access to e-cigarettes and paraphernalia did not pose any significant barriers. Poland’s introduction of a new age limit on e-cigarette sales may help limit the number of youth who purchase e-cigarettes from vape shops.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Vehicle routing is a critical factor in municipal solid waste (MSW) collection planning and operations. Poor routing can introduce inefficiencies and cause targeted levels of services or performance to be missed irrespective of the level of resource application. Trial and error approaches have been proven to be not the best in the planning and prediction of expected performance. This study explores various Geographic Information System (GIS) tools and analysis techniques, and how they can be applied to optimizing vehicle routes in light of challenging site conditions. Using Adentan West residential area, suburb of Accra Ghana as a case study, current performance of the trial and error method was measured and a GIS computer model was used to evaluate various optimization scenarios to determine the level of savings that can be made. Field measurements were taking with Global Positioning System (GPS) devices for waste collection activities in areas with varying characteristics and conditions, and data analysed for one selected vehicle operating four days per week. It was found that, for a scenario where only the bin collection order was optimized while route selection was restricted by the ArcGIS Network Analyst, 2.6% of travel distance and 2.21% of travel time were saved. For the second scenario where only the route selection was optimized while order of bin collection was restricted, 4.1% and 1.5% of travel distance and time respectively were saved. For a third scenario where both the order of collection and route selection were together optimized, 10.9% and 3.7% of travel distance and time respectively were saved. Lastly, by regrouping all the bins for daily collection, 4.5% and 1.2% of travel distance and time respectively were saved. The results demonstrated that there is always room for optimization of solid waste collection routing irrespective of site constraints and other challenges that the nature of bin distribution pose to drivers. In developing countries like Ghana, where there is high demand for services in the face of limited road network access, application of GIS in optimization of routes will guide providers in planning and subsequently make more savings in fuel consumption, vehicle maintenance and cost of man-hours.

In recent years, Malaysia has faced environmental challenges caused by municipal solid waste, especially household waste, during the Covid-19 pandemic. Among all the household waste, plastic and paper are the most prominent waste that causes environmental hazards. Several recycling associations in Malaysia have carried out their practices for better waste sustainability and management to curb the increasing amount of household waste. However, the effectiveness is still vague in achieving smart and effective household waste management. Therefore, this paper aims to investigate Malaysia’s household waste management, mainly in three significant municipalities in Malaysia for Kuala Lumpur, Penang and Melaka, in becoming a resilient and sustainable city by addressing two main research questions 1) What are the key factors for ensuring the more success move for future household waste management in cities? and 2) How will the 3 municipalities address their waste issues based on the key factors from RQ1, respectively? This paper reviewed 13 waste management articles and explores the potential of the four factors of waste management from the perspective of technology and data, economy, social and governance. The discussed factors and models contributed to an integrated future-proofing framework that focuses on smart waste tracking, an gamified awareness education, and strict policies to control waste management are the way forward for the future of smart cities household waste management.

Agricultural product like cassava produces huge amounts of waste when processed to consumable goods. The waste generated is generally considered to contribute largely to environmental pollution. This study therefore investigates the waste management practice that is adopted by cassava processors in Ogun State, Nigeria. Five (5) Local Government Areas (LGAs) dominant in processing cassava were selected for the study on the basis of spatial location distribution; landmass and population. The survey involved the use of structured questionnaires administered to cassava processors of the selected LGAs. The Statistical Package for Social Sciences (SPSS) software application and descriptive statistics were used for data analysis. Results of the analysis show that majority (70%) of the cassava processors are females. Cassava peel constitutes 10% of the waste produced, of which 91% are heaped at refuse dump in most communities. Results also reveal that 86.3% of cassava residues are used for animal feeds. Other findings show that the peels when dried are used as bio-fuel for cooking and there is a significant potential for biogas production. From the data captured from respondent during the study, most processors are willing to pay for an improved waste management system. The study therefore suggests proper waste management of cassava waste to minimize environmental pollution.

Target 12.3 of the United Nations Sustainable Development Goals (SDGs) calls for halving per capita global food waste at the retail and consumer levels, by 2030. The Food Waste Index is suggested as a methodology for grasping the situation. This paper focuses on the consumer level (household food waste). We argue that in order for generating useful information for devising and implementing effective measures for reducing food waste, it should be measured at Level 3 of the Food Waste Index, based on sorting analysis of generated waste, making a distinction between avoidable and non-avoidable food waste. Furthermore, a breakdown by sub-categories that reflect the flow of food in the household could help identify target behaviours. We have developed a categorisation scheme that is internationally agreeable and adoptable, and 1) generates useful information for policy-making and for tackling with reduction of food waste, 2) makes clear the concept of avoidable food waste, and 3) is practical and does not overcomplicate the work of grasping the situation of food wastage. Results of workshops regarding this scheme suggest that the scheme satisfies the criteria. This scheme has been applied to a few sorting analyses of household food waste in Japan, and their results are compared.

Increased proliferation of IT services in all sectors has reinforced the adoption and diffusion across all levels of education and training institutions. However, lack of awareness of and knowledge about the key challenges and opportunities of elearning, seem to allude policymakers, resulting in low adoption or increased failure rate of many e-learning projects. Our study tries to address this problem through a review of relevant literature in e-learning. Our goal was to draw from the existing literature, insights into the opportunities and challenges of e-learning diffusion, and the current state-of-research in the field. To do this, we employed a systematic review of literature on some of the salient opportunities and challenges of e-learning innovation for educational institutions. These results aimed to inform policymakers and suggest some interesting issues to advance the research and adoption and diffusion of e-learning. Moreover, the bibliometric analysis shows that the field is experiencing high research attraction among scholars. However, several research areas in the field witnessed relatively low research paucity. Based on these findings, we discussed topics for possible future research.

Recycling and waste management have garnered immense popularity in recent years, but few studies have been carried out regarding these systems. Therefore, an in-depth literature review was done in order to highlight the different sectors of the recycling system that need to be reformed. Hence this study examined recycling and waste management systems within three categories–medical, municipal, and plastic–that were carried out pre and post COVID by reviewing previous studies, technical reports, and annual reports. This was done by visiting numerous academic search engines alongside online resources that were utilized to assemble literature related to waste and recycling systems. Continuing a recurring idea was that no matter the type of waste, further research regarding all waste should be carried out. Additionally, since recycling and waste management are a vital part of our society, and seeing how unpredictable events such as the pandemic may be, it is paramount that that research is done not only on how the pandemic has affected systems now, but also how we can learn from current issues to utilize them for future “waste shocks”.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

This work investigated the effects of manufacturing variations including coil resistance, initial pod mass, and e-liquid color on coil lifetime and aerosol generation of Vuse ALTO pods. Random samples of pods were used until failure (where e-liquid was consumed, and coil resistance increased to high value indicating a coil break). Initial coil resistance, initial pod mass, and e-liquid net mass ranged between 0.89 to 1.14 [], 6.48 to 6.61 [g], and 1.88 to 2.00 [g] respectively. Coil lifetime with light color e-liquid was (mean) = 149, (standard deviation) = 10.7 puffs while pods with dark color e-liquid was = 185, = 22.7 puffs with a difference of ~36 puffs (p &lt;0.001). Total mass of e-liquid consumed until coil failure was = 1.93, = 0.035 [g]. TPM yield per puff of all test pods for the first session (brand new pods) was = 0.0123, = 0.0003 [g]. During usage, TPM yield per puff of pods with light color e-liquid was relatively steady while it was continuously decreasing for pods with dark e-liquid. Coil lifetime and TPM yield per puff were not correlated with either variation in initial coil resistance or variation in initial pod mass. The absence of e-liquid in the pod is an important factor in causing coil failure. Small bits of the degraded coil could be potentially introduced to the aerosol. There is a potential correlation of e-liquid color with both coil lifetime and TPM yield per puff. Change of e-liquid color might have been a result of oxidation which changed some nicotine into nicotyrine.

This study focuses on a new class of functions called sub-b-s-preinvex, that is a generalization of sub-b-s-convex and preinvex functions, and discusses some of their properties. A new sub-b-s-preinvex programming is introduced and the sufficient conditions of optimality under this type of function is established.

The alkylation of 1,1,2-trimethyl-1H-benzo[e]indole with 2-chloroacetamide, followed by work-up of the reaction mixture with a base and the subsequent treatment of a crude product with acetic acid gives 10a,11,11-trimethyl-10a,11-dihydro-8H-benzo[e]imidazo[1,2-a]indol-9(10H)-one. The structure assignments were based on data from ¹H, ¹³C and ¹⁵N NMR spectroscopy. The optical properties of the obtained compound were studied by UV-vis and fluorescence spectroscopy.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

The growing concern about climate change and the recognition of the planet’s limits led society to look for alternatives that promote the balance between the natural and the built environment. The circular economy emerges as an alternative to the linear economic model, inspired by natural metabolisms, by circulating resources in continuous loops, where their intrinsic value is maintained and improved. This research proposes a closed-loop strategy in the built environment by studying innovative constructive solutions that aim to find use, value, and inspiration in what is considered waste. A literature review is conducted on the circular design strategies, re-use and recycle typologies, and waste transformation processes. Then, the development of a methodology for qualitative evaluation and selection of re-used and upcycled construction materials from post-consumer waste and by-products is presented and then applied to thirty-five cases of constructive solutions from plastic, wood, paper, steel, aluminium, and agricultural waste. The research reports that the developed framework is adequate. The analysed alternative materials have good environmental performance and can be used as building materials despite their functional limitations, reflecting the enormous potential of waste as a resource for the construction industry.

The nationwide lockdown imposed to control the spread of novel coronavirus induced dramatic alterations in different sectors of the Nepalese governance, including Solid Waste Management (SWM) practices. The study identifies SW collection gaps in seven major cities of Nepal and highlights the municipal and public households on SW management practices before and during the lockdown to emphasize the linkage between COVID-19 and SWM. It includes information on solid waste status, collection frequency and coverage, workers safety practices, types of vehicles operated for collection and alternative methods adopted by households to manage SW during the lockdown. For this, 1329 households survey and key informant interviews were conducted in seven cities of Nepal during the lockdown. It was found that although the coverage of the collection service was similar during the pandemic, there was a drastic decrease in the collection frequency leading to a collection gap of around 570 tons/day. More than 50% of the surveyed households adopted no proper alternative measures as they claimed that they stored solid waste with proper management so that municipal authorities can take it. The study reveals poor occupational health and safety practices among the solid waste workers due to the unavailability of safety gears and equipment despite being aware of the modes of transmission of the virus. The pandemic exacerbated the challenges of smooth SWM as it is an essential and needy service. This study highlights the need for a timely strategic management framework to be developed by the government to continue the smooth SWM practices during the lockdown.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

The possibility of making precious stones from radioactive waste is being considered. Vitrified and cemented radioactive waste (RW) is considered as an artificial rock belonging to aluminosilicates and calcites. Two methods are proposed for the manufacture of radioactive gemstones from RW and their subsequent storage with the possibility of sale, resale, inheritance, and so on. That is, RW is considered as real estate in which capital can be invested. After decontamination in hundreds and thousands of years, it will be of scientific, historical, jewelry interest.

The new climate law introduces a policy of sustainable construction, the assumption of which is the reduction of CO2 by the construction industry and the use of environmentally friendly materials, such as agricultural, mineral, and recycled waste, while limiting the consumption of natural resources. The article is a literature review that analyzes selected waste materials from various sectors of the economy that can be used as additives or partial substitutes for natural resources in the production of cement and in and cement building materials, the production of which reduces CO2 emissions, producing materials with high mechanical strength and environmentally friendly.

An adequate number of waste management facilities is the key element to meet circular economy goals. Using empirical data taken from official sources the research framework bases on an econometric model to compare the elasticity of cost on quantity of different alternatives such as waste-to-energy facilities, mechanical biological facilities and landfills impact on waste management cost. Results suggest that both waste-to-energy facilities (-0.278%) and landfills (-0.38%) concur to lower the cost while the higher the percentage of waste sent to mechanical biological treatment facilities, the higher the cost (0.788%). This figure deserves to be examined in more details as such facilities represent an intermediary step in the chain which efficiency depends on the industrial organization of the chain.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

Multi-sensor data fusion of E-tongue and E-nose can provide a more comprehensive and more accurate analysis results. However, it also brings some redundant information, it is a hot issue to reduce the feature dimension for pattern recognition. In this paper, the taste-olfactory data fusion based on E-tongue and E-nose combined with Support Vector Machine (SVM) was used to classify five different beers. First, the taste and olfactory feature information were obtained based on E-tongue and E-nose. Second, the original feature data of single system were fused, then Principal Component Analysis (PCA) was applied to extract principal components, Genetic Algorithm-Partial Least Squares (GA-PLS) was used to select the characteristic variables, 20 subsets were generated with those variables based on the best Variable Importance of Projection (VIP) score. Finally, the classification models based on SVM were established, also c and g of SVM were calculated by Grid Search (GS), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO), the classification results of all subsets were obtained. The results showed that the classification accuracy using data fusion was much higher over single E-tongue and single E-nose, and the variable selection method by VIP had the best classification performance in #12 subset coupled with GA-SVM.

Background - Chronic kidney disease with unknown aetiology (CKDu) is a progressing disease which is affecting many Sri Lankans’ yearly, this disease is slow progressive, irreversible and asymptomatic disease. Patients suffering from CKDu over the past two decades have been evaluated using the estimated glomerular filtration rate (e-GFR). This is the standard test performed under WHO guidelines to investigate and grade the CKDu, and this creatinine clearance is measured in this in order to grade the patient. Backache has been a common symptom presented in most of the chronic kidney disease patients (CKD), patients with CKDu are liable to get backache due to the renal failure that takes place (Jayathilake et al., 2013; Redmon et al., 2016). Objective – To detect a correlation between serum creatinine values and level of backache presented in the patient. Method -Using an interview based questionnaire to assess patients’ body condition and the degree of backache is assessed, 59 patients were part of the study for a period of five months and had an average age of 60.3 years. The questionnaire answers are scaled into four main types of backache from the least to the most painful based on the pain scale adapted from Kapkia. Serum creatinine is measured using an automated analyzer which is measured using Jaffe’s reaction. Using Pearson R correlation, the relationship was determined between serum creatinine and backache (Kafkia et al., 2011). Results – The results were obtained for 58 patients (n=58), where the mean backache score was 2.30 and mean serum creatinine value 2.77. The Pearson R value obtained was 0.01 which is indicating almost no relationship between backache and serum creatinine. Patients with stage 3 kidney disease (n=14) had an average E-GFR of 38.0, stage 4 (n=38) with 22.3 and stage 5 (n=6) with 14.0. Conclusion – Backache can be used an indicator of CKDu since it is presented in most patients’ suffering from the disease but unable to be used to determine the stage of CKDu suffered by the patient due to the external causes that leads to backache. Several predisposing factors such as temperature, water source and agricultural activity can influence the backache.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

Insecticide testing facilities that evaluate a variety of vector control products may generate large amount of hazardous wastes from routine operations. These wastes originate from degraded technical grade materials, sprayed substrates, redundant stock or working insecticidal solutions. The washing of Long-Lasting Insecticidal Nets (LLINs) during preparation for laboratory and experimental hut trials also contribute to waste water with insecticide content. Human and environmental exposure to insecticidal waste can occur during transport, categorization, storage and disposal in resulting in environmental pollution and potential health effects. Various national and international guidelines have been devised for safe disposal and should be strictly followed to avoid adverse effects on humans or environment. The current paper describes a case study from insecticide test facility in north-eastern Tanzania in management of insecticidal waste.

Solid-state lighting has been replacing conventional lighting in the market, raising concerns for implementing an efficient end-of-life management system. Since LED waste streams have not been quite dominant, characterization studies (product-level characteristics, component-wise information, bill of materials, diversity, and differences) are inconsistent and having substantial gaps. This study investigates the end-of-life LED lamp literature, focusing on the bill-of-materials, and reveals that the characterization procedure suffers from a severe lack of sample representativeness. Consequently, characterization results are widely varied and not generalizable. Moreover, most of the studies did not inform and document the detailed sample characteristics, precluding the possibility of identifying reasons for variation. Combining available information from the recent studies, we present a mass distribution at the component level, exemplifying the prospect for meeting EU regulatory limit and the need for more insight at the lamp and component level. To fill the disconnection between lamp level characteristics and component and material content, we propose a characterization protocol that carefully documents lamp, component, and material level information by establishing a lamp-component–material composition nexus. The protocol may help researchers, policymakers, and industrial stakeholders conduct a systematic characterization, analyze complexities and prepare for a sustainable solution.

The investment in digital e-Health services is a priority direction in the development of global health care systems. While people are increasingly using the Web for health information, it is not entirely clear what is the physicians’ attitude towards digital transformation, and the acceptance of new technologies in healthcare. The aim of this cross-sectional survey study was to investigate physicians’ self-digital skills, and their opinions on obtaining online health knowledge by patients, as well as the recognition of physicians’ attitudes towards e-Health solutions. Principal Component Analysis (PCA) was performed to emerge the variables from self-designed questionnaire, and cross-sectional analysis comparing descriptive statistics and correlations for dependent variables using the one-way ANOVA (F-test). 307 physicians participated in the study, reported using the internet mainly several times a day (66.8%). Most participants (70.4%) were familiar with new technologies and rate their e-Health literacy high, although 84.0% reported the need for additional training in this field, and reported a need to introduce a larger number of subjects shaping digital skills (75.9%) in medical studies 53.4% of physicians perceived Internet-sourced information as sometimes reliable, and in general assessed the effects of using it by their patients negatively (41.7%). Digital skills increased significantly with frequency of internet use (F = 13.167; p = 0.0001), and decreased with physicians’ age, and the need for training. Those who claimed that patients often experienced health benefits from online health showed higher digital skills (-1.06). Physicians most often recommended their patients to obtain laboratory test results online (32.2%), and to arrange medical appointments via the Internet (27.0%). Along with the deterioration of physicians’ digital skills, the recommendation of e-Health solutions decreased (r = 0.413), and lower the assessment of e-Health solutions for the patient (r = 0.449). Physicians perceive digitization as a sign of the times, and frequently use its tools in daily practice. The evaluation of Dr. Google’s phenomenon and online health is directly related to their own e-Health literacy skills, but there is still a need for practical training to deal with digital revolution.

The new need to move to an online mode of administration has necessitated the adoption of Software-as-a-Service (SaaS) and Platform-as-a-Service (PaaS). The conventional paper-based administrative memorandum is relatively costly, requires manpower, insecure and non-confidential, prone to unauthorized access and has a relatively slow cycle time; among others. An electronic memo (e-memo) can save cost, offer high speed of processing, reliability and security. The aim of this work was to conceptualize, design and develop a novel semantic web-based memo platform that allows for handling memos within an organization. The tools used include HTML, CSS, PHP, JavaScript, jQuery and AJAX, MySQL. The developed system was tested in three stages. Testing was done in the Department of Computer Science of the institution of case study, then in the Faculty of Science and finally in the entire Lagos State University. Agile development method was used in the development process. The designed system was hosted on a cloud-server and a total of 43 test cases were considered and an average of four minutes was recorded for a complete memo cycle. eMemo allows users to generate, sign, treat and memo electronically. It is such a useful tool that will enhance information processing in a faster, standardized and more secure manner.

Waste recovery is an important aspect towards human and environmental health protection. Unfortunately, proper food waste management is among the serious challenges in the field of solid waste management worldwide. Therefore, it is of great importance to conduct studies towards achieving efficient and cost-effective approaches for food waste management. This study investigated the potential of recovering food waste through maggots’ production as animal feed. The influence of fly attractant application on maggot production was also investigated. The study also investigated the potential of maggot production for waste recovery and reduction. Four different types of food waste (starch food leftovers, rotten bananas and peels, rotten pineapple and peels, and rotten oranges) were used in the investigation process. From the results, it was observed that the application of fly attractants had a significant effect on the production of maggots as determined by the weights after harvesting. Average weight of 94 g/kg of maggot was achieved from banana materials with an application of fly attractant during the 8th day of the cultivation; which is equivalent to a 32.4% increase from the same day when the material was cultured without applying fly attractant. Also, from the starch materials, about 77 g/kg of maggot weight was achieved; which is a 54.6% increase from the same day and the same material but without application of fly attractant. Moreover, the relative dry weight reduction in the trials varied from 52.5% to 82.4%.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

E-petitioning is a useful object of study for observing the potential emergence of a new relationship to politics and new forms of political participation. Access to a dataset of hundreds of thousands of users of an electronic petitioning platform, provides the opportunity to overcome a certain number of limitations that are associated with traditional methods of studying political participation, since it allows us to focus on the reality of the signatories’ behaviour rather than on their declarations. We follow the traces left by the petitioners on this site to better understand the process of dissemination of an online petition, and its linked with offline activities. Our examination of the three most signed petitions in the ‘environment’ category, combining an analysis of their petitioning dynamics and an analysis of the comments attached to them, allows us to show: firstly, that there is an interwoven relationship between the local anchoring of the mobilisation and the processes of dissemination by which petitions extend from local signatories to signatories who are geographically more distant; and secondly, that it is not accurate to imagine that just anyone can sign any petition, since petitioning dynamics proceed from one person to the next, whether these dynamics start from a pre-existing local anchorage on the ground, or act through a platform effect which is dependent on the attractiveness of the petition in question.

Enteroaggregative Escherichia coli (EAEC) is an emerging pathogen frequently associated with acute diarrhea in children and travelers to endemic regions. EAEC was found the most prevalent bacterial diarrheal pathogen from hospitalized Bolivian children less than five years of age with acute diarrhea from 2007 to 2010. Here, we further characterized the epidemiology of EAEC infection, virulence genes, and antimicrobial susceptibility of EAEC isolated from 414 diarrheal and 74 non-diarrheal cases. EAEC isolates were collected and subjected to a PCR-based virulence gene screening of seven virulence genes and a phenotypic resistance test to nine different antimicrobials. Our results showed that atypical EAEC (a-EAEC, AggR-negative) was significantly associated with diarrhea (OR, 1.62, 95% CI, 1.25 to 2.09, P < 0.001) in contrast to typical EAEC (t-EAEC, AggR-positive). EAEC infection was most prevalent among children between 7 - 12 months of age. The number of cases exhibited a biannual cycle with a major peak during the transition from warm to cold season (April – June). Both typical and a-EAEC infections were graded as equally severe; however, t-EAEC harbored more virulence genes. aap, irp2, and pic were the most prevalent genes. Surprisingly, we detected 60% and 52.6% of multidrug resistance (MDR) EAEC among diarrheal and non-diarrheal cases. Resistance to ampicillin, sulfonamides, and tetracyclines was most common, being the corresponding antibiotics, the ones that are frequently used in Bolivia. Our work is the first study that provides comprehensive information on the high heterogenicity of virulence genes in t-EAEC and a- EAEC and the large prevalence of MDR EAEC in Bolivia.

For better export performance in cross border e-commerce, a contingency model integrates e-commerce into traditional export marketing strategy (EMS) with internal and external determinants of EMS. However, EMS of Micro, small, and medium-sized enterprises (MSMEs) is understudied. This study validates and modifies existing model for MSMEs. As a qualitative study, multiple sources of data including interviews, internal documents, and group discussions were used regarding business cases of entrepreneurs and supporting organizations in Mongolia and Korea. This research suggets contingency model for MSMEs with modified factors and different strategies in each factor. Specifically, intermal determinants are managerial capability, product competitiveness, and strategic marketing orientation. External determinants are export market competitivceness, export market infrastructure and entry barriers. EMS for MSMEs consists of the same factors with the original model but come up with different strategies. Theoretical and managerial implications were discussed.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

(1) Background: Spain launched an official campaign, #EsteVirusLoParamosUnidos, to try and unite the efforts of the entire country through citizen cooperation to combat coronavirus. The research goal is to analyze the Twitter campaign’s repercussion on general citizen feeling. (2) Methods: The research is based on a composite design that triangulates from a theoretical model, a quantitative analysis and a qualitative analysis. (3) Results: Of the 7357 tweets in the sample, 72.32% were found to be retweets. Four content families were extracted: politics, education, messages to society and defense of occupational groups. The feelings expressed ranged along a continuum, from unity, admiration and support at one end to discontent and criticism regarding the health situation at the other. (4) Conclusions: The development of networked sociopolitical and technical measures that enable citizen participation facilitates the development of new patterns of interaction between governments and digital citizens, increasing citizens’ possibilities of influencing the public agenda and therefore strengthening citizen engagement vis-à-vis such situations.

A E. Crassipes is considered a problem in different aquatic ecosystems, due to its abundance could become a solution to design and build economic and efficient treatment plants, and especially for the production of biofuels such as bioethanol. The objective of this research is to design and implement a sustainable development process between phytoremediation and bioethanol production with E. crassipes, evaluating the incidence of chromium adhered to the biomass of this plant in the production of bioethanol. Materials and methods: A system was installed to evaluate the phytoremediation with E crassipes with water loaded with chromium, determining the effectiveness of this plant to remove this heavy metal even if it is alive in a body of water. After this process, we proceeded to bring the biomass loaded with chromium to bioreactors to evaluate the production of bioethanol, assessing three types of biomass, one without chromium adhered and the other two with chromium adhered to its plant structure. There was an impact of the ethanol production of the E crassipes due to the presence of chromium, but this production can be taken into account for the assembly of an integral system of phytoremediation and bioethanol production, making the most of this biomass.

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

In the present work we study the properties of geodesic sub-$ (\alpha,b,s) $-preinvex functions on Hadamard manifolds and establish some basic properties in both general and differential cases. Further, we study sufficient conditions of optimality and proved some new inequalities under geodesic sub-($ \alpha,b,s $)-preinvexity.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

Mining is an important industry that provides products and services through infrastructure systems worldwide. However, the global development promotes the steady growth and accelerated demand for minerals, resulting in the accumulation of hazardous waste in land, sea and air environments and, consequently a series of environmental and health problems. Restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits over reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper critically explores available literature on the main techniques of mining tailing recycling, and discusses leading recycling technologies, including the advantages and drawbacks, as well as future perspectives. The findings of this review contribute as a reference for scholars as well as support for decisionmakers concerning the related environmental issues.

Forest recreation can be successfully used for the psychological relaxation of respondents and can be used as a remedy for common problems with stress. The special form of forest recreation intended for restoration is forest bathing. These activities might be distracted by some factors, such as viewing buildings in the forest or using a computer in nature, which interrupt psychological relaxation. One factor that might interrupt psychological relaxation is the occurrence of an open dump in the forest during an outdoor experience. To test the hypothesis that an open dump might decrease psychological relaxation, a case study was planned that used a randomized, controlled crossover design. For this purpose, two groups of healthy young adults viewed a control forest or a forest with an open dump in reverse order and filled in psychological questionnaires after each stimulus. A pretest was used. Participants wore oblique eye patches to stop their visual stimulation before the experimental stimulation, and the physical environment was monitored. The results were analyzed using the two-way repeated measures ANOVA. The measured negative psychological indicators significantly increased after viewing the forest with waste, and the five indicators of the Profile of Mood States increased: Tension-Anxiety, Depression-Dejection, Anger-Hostility, Fatigue, and Confusion. In addition, the negative aspect of the Positive and Negative Affect Schedule increased in comparison to the control and pretest. The measured positive indicators significantly decreased after viewing the forest with waste, the positive aspect of the Positive and Negative Affect Schedule decreased, and the Restorative Outcome Scale and Subjective Vitality scores decreased (in comparison to the control and pretest). The occurrence of an open dump in the forest might interrupt a normal restorative experience in the forest by reducing psychological relaxation. Nevertheless, the mechanism of these relevancies is not known, and thus, it will be further investigated. In addition, in a future study, the size of the impact of these open dumps on normal everyday experiences should be investigated. It is proposed that different mechanisms might be responsible for these reactions; however, the aim of this manuscript is to only measure this reaction. The identified psychological reasons for these mechanisms can be assessed in further studies.

The aim of this research study was to develop hydrogels samples for using in potential biomedical applications. Hydrogels consisting of different volumes of keratin, polyvinyl alcohol (PVA), Polyvinylpyrrolidone (PVP), and starch. The keratin is derived from the chicken was the primary material on the hydrogels due to attractively for the potential wound healing application. The hydrogel samples were made by using the freeze‑thawing method, and they were examined using the Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), porosity amusement, swelling ratio and keratin release kinetic models that analyzed using (zero-order, first-order Higuchi and Korsmeyer-Peppas models). These results were indicated that feather keratin could use with formulated hydrogels suitably for controlled keratin release studies .

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

Resilience embodies the personal qualities that enable one to thrive in the face of adversity. A previous Italian study showed that injured workers had a lower level of resilience than non-injured workers. The aim of this paper is to examine the relationship between occupational injuries and psychological resilience. The subjects were 197 drivers from two Finnish waste transport companies. As a part of larger questionnaire, they fulfilled the Connor-Davidson Resilience Scale, which consisted of 25 items. Drivers reported their occupational injuries during the last three years. The drivers involved in occupational injuries had higher score (average 69.3) on Connor-Davidson Resilience Scale than drivers avoided injuries (67.7). According to Student’s t-test the difference between groups was highly significant (t = 40.44, df = 196, p<0.001). The result of this study was contradictory to earlier Italian study. One explanation may be that the Italian study was done with traumatic context with seriously injured patients. Waste transport drivers were rather young and fit males, who had suffered only minor injuries.

Waste orange peel represents a heavy burden for the orange juice industry, estimated in several million tons per year worldwide; nevertheless, this by-product is endowed with valuable bioactive compounds, such as pectin, polyphenols and terpenes. The potential value of the waste orange peel has stimulated the search for extraction processes, alternative or complementary to landfilling or to the integral energy conversion. This study introduces controlled hydrodynamic cavitation processes, as a new route to the integral valorization of this by-product, based on simple equipment, speed, effectiveness and efficiency, scalability, and compliance with green extraction principles. Waste orange peel, in batches of several kg, was processed in more than 100 L of water, absent any other raw materials, in a device comprising a Venturi-shaped cavitation reactor. The extractions of pectin, endowed with a very low degree of esterification, polyphenols (flavanones and hydroxycinnamic acid derivatives), and terpenes (mainly d-limonene) were effective and fast (high yield, few min of process time), as well as the biomethane generation potential of the process residues was effectively exploited. The achieved results proved the viability of the proposed route to the integral valorization of waste orange peel, though wide margins exist for further improvements.

This study was undertaken to forecast waste generation rates of accommodation sector of North Cyprus as a case. Three predictor models including multiple linear regression (MLR), artificial neural networks (ANNs) and central composite design (CCD) were applied to predict the waste generation rate during the lean and peak seasons. ANN showed highest prediction performance, specifically, lowest values of the standard error of prediction (SEP = 2.153), mean absolute error (MAE=1.378) and highest R2 value (0.998) confirmed the accuracy of the model. The analysed wastes were categorised into recyclable, general waste and food residues. The authors estimated the total waste generated during the lean season as 2010.5 kg/day, in which large-sized hotel accounted for largest fraction (66.7%), followed by the medium hotels (19.4%) and guesthouse accounted for smallest part (2.6%). During the peak season, about 49.6% increases in the waste generation rates were obtained. Interestingly, 45% of the wastes were generated by the British tourists while the least waste was generated by African tourists (7.5%). The ANN predicted that the small and large hotels would produce 5.45 and 22.24 tons of waste by the year 2020, respectively. The findings herein are promising and useful in establishing a sustainable waste management system.

The “Pay-as-you-throw” scheme, PAYT, is an economic instrument of waste management that implements the “polluter pays” principle by charging inhabitants of municipalities according to the amount of residual, organic and bulky waste they send for third-party waste management. When combined with well-developed infrastructure to collect the different waste fractions (residual waste, paper and cardboard, plastics, bio waste, green cuttings, many recyclables) as well as with a good level of citizen’s awareness, its performance has frequently been linked to high collection rates of recyclables. However, the establishment and operation of PAYT systems can require significant resource inputs from municipalities. In this paper, PAYT is analysed through a case study from the German County of Aschaffenburg, covering nearly 20 years of implementation across 173,000 inhabitants. Key performance indicators applied include temporal trends in the county’s recyclables collection rate, waste treatment fees for residents and municipal waste management costs, benchmarked against German municipalities not implementing PAYT.

This article is an effort to scrutinize the role of Information Technology development in the chronological transformation of Urban Planning domain using the exploratory research approach. In this research, it is argued that the theoretical and practical understanding of Urban Planning should absorb and integrate the bright outcome of the rise of Information and Technology to foster congruent future urban development. The article addresses the trends of transformation in the urban planning domain through the myopic lens of the expansion of information and communications technology era followed by investigating the key drivers shaping the interaction between modern-day urban planning and information technology considering both the dark and bright sides into account.

Sexual issues and treatment side effects are not routinely discussed with men receiving treatment for prostate cancer and support to address these concerns is not consistent across settings. This study evaluates a brief e-learning resource designed to improve sexual wellbeing support and examine its effects on healthcare professionals’ sexual attitudes and beliefs. Healthcare professionals (n=44) completed an online questionnaire at baseline which included a modified 12-item sexual attitudes and beliefs survey (SABS). Follow-up questionnaires were completed immediately after the e-learning and at 4 weeks. Data were analysed using one-way, repeat measures ANOVAs to assess change in attitudes and beliefs over time. Significant improvements were observed at follow-up for a number of survey statements including ‘knowledge and understanding’, ‘confidence in discussing sexual wellbeing’ and the extent to which participants felt ‘equipped with the language to initiate conversations’. The resource was seen as concise, relevant to practice, and as providing useful information on potential side effects of treatment. Brief, e-learning has potential to address barriers to sexual wellbeing communication and promote delivery of support for prostate cancer survivors. Practical methods and resources should be included with these interventions to support implementation of learning and long-term changes in clinical behaviour.

E-learning with many outstanding advantages in training has drastically changed the self-study process due to the ability to personalize and effectively meet the learning activities of learners. E-learning and building an e-learning environment are currently paying attention and being deployed in many universities in Vietnam with different scope and levels. Especially in the current period, when science and technology are developing, many applications of technology and technology products have been applied in the field of education, changing the way of teaching and learning activities, the practice of both lecturers and students. Big Data and Artificial Intelligence (AI) technologies have replaced people not only for manual labor but also for intellectual labor, including the teaching of teachers. Many software applications have been used to replace people in the transmission of knowledge, testing, and evaluation of training quality, especially E-learning online training programs. However, in Vietnam today, the output quality of these online training programs has not been highly appreciated compared to similar programs in the world. The cause of this situation is that the training, teaching, and learning are not effective. Therefore, in this article, I will give some analysis, evaluate the current teaching and learning methods and propose solutions to enhance the interaction and initiative in the teaching and learning process of lecturers and students to improve the quality of online training in the future.

In this work, two embroidered textile moisture sensors are characterized with three different conductive yarns. The sensors are based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidered conductor yarn. The performance comparison of 3 different type of conductive yarns has been addressed. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 30% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity and the used conductor yarns. This dependence points out the optimum conductive yarn to be used to develop wearable applications for moisture measurement.

Internet-led labour market has become so competitive forcing many organisations from different sectors to embrace e-recruitment. However, realising the value of the e-recruitment from a Requirements Engineering (RE) analysis perspective is challenging. This research is motivated by the results of a failed e-recruitment project conducted in military domain which is used as a case study in this research. After reviewing the various challenges faced in that project through a number of related research domains, this research focuses on two major problems which are the (1) difficulty of scoping, representing, and systematically transforming recruitment problem knowledge towards e-recruitment solution specification; and (2) the difficulty of documenting e-recruitment best practices for reuse purposes in an enterprise recruitment environment. In this paper, a Problem-Oriented Conceptual Model (POCM) with a complementary Ontology for Recruitment Problem Definition (Onto-RPD) is proposed to contextualise the various recruitment problem viewpoints from an enterprise perspective and to elaborate those problem viewpoints towards a comprehensive recruitment problem definition. The POCM and Onto-RPD are developed incrementally using action-research conducted on three real case studies: (1) Secureland Army Enlistment, (2) British Army Regular Enlistment, and (3) UK Undergraduate Universities and Colleges Admissions Service (UCAS). They are later evaluated in a focus group study against a set of criteria. The study showed that the POCM and Onto-RPD provide a strong foundation for representing and understanding the e-recruitment problems from different perspectives.

Despite the uptake of tobacco smoking declining in the UK, smoking is still the leading cause of preventable poor health and premature death. While improved approaches to smoking cessation are necessary, encouraging and assisting smokers to switch by using substantially less toxic non-tobacco nicotine products may be a possible option. To date few studies have investigated the rates of smoking cessation and smoking reduction associated with the free provision of electronic-cigarettes (e-cigarette) to smokers. In this study the Blu Pro e-cigarette was given to smokers for use in place of tobacco for 90 days. The rates of smoking abstinence and daily smoking patterns were assessed at baseline 30 days, 60 days and 90 days. The response rate was 87%. After 90 days, the complete abstinence rate was 36.5% from 0% at baseline. Frequency of daily smoking reduced from 88.7% to 17.5% (P<0.001) and median consumption of cigarettes/day from 15 to 5 (P<0.001). Median days per month participants smoked also dropped from 30 to 13 after 90-days (P<0.001). On the basis of these results there may be value in smoking cessation services and other services ensuring that smokers are provided with e-cigarettes at zero or minimal costs for at least a short period of time.

The contents of Education for Sustainable Development (ESD) should be included in teachers’ initial and advanced training programs. In order to determine the key competences for sustainability, creating a Sustainable Consciousness is one of the main foundations. However, there are not many empirical studies that deal with consciousness from education. In this context, e-portfolio appears as a tool that promotes reflection and critical thinking, key competences for consciousness development. This work intends to propose a categorization system to extract types of consciousness and identify trainee teachers’ levels of consciousness. For this research work, of an eminently qualitative nature, we have selected twenty-five portfolios of students in the last year of the School of Education at the University of Macerata (Italy). The qualitative methodological procedure followed allowed to deduce three bases that shape trainee teachers’ consciousness: thinking, representation of reality and type of consciousness. We concluded that the attainment of a Sustainable Consciousness in teachers requires activating and developing higher levels of thinking, as well as a projective and macrostructural representation of reality.

Clinical training in medical schools in Spain is performed by rotations in university hospitals. During these internships, students are expected to acquire and master basic procedural skills. However, the assessment tools available rarely check whether these skills are completely acquired by the students. We have used an e-portfolio to determine the optimal number of times the students need to repeat a procedure to be able to perform it independently. The results were compared with the actual performance during the internships. An e-portfolio collected qualitative information about the internships. Quantitative information was also requested about the number of times each clinical skill was performed. Later, a survey asked these students and their teachers the optimal number of times each skill should be repeated before it could be considered fully acquired. The questionnaire was answered by 98.6% of the students and 70.3% of their teachers. Out of the 21 clinical skills and procedures selected, both students and their tutors agreed in a similar optimal value in 16 of them; only in five of them, teachers thought that students needed a greater number of times than that selected by the students. When these optimal values were compared with the actual values recorded in the portfolio during the internships, it was found that about half of the clinical skills were carried out less frequently than expected, thus providing an important feedback about the internships. Quantitative information collected in portfolios reveals a moderate mismatch between students and tutors perceptions of their training needs.

The basic principles of geological risk calculation through Probability of Success (PoS) are mostly applied for numerical estimation of additional hydrocarbon existence in proven reservoirs or potential hydrocarbon discoveries in selected geological regional subsurface volume. It can be tailored and validated for a comprehensive input dataset collected in the selected petroleum province, adapted by dividing up geological events into several probability categories and classes. The most applied categories are (existence of) reservoir rocks, traps and isolators, source rocks, migration pathways and preservation conditions for hydrocarbons The methodology results in unique probability values as multiplication of independent statistical events, which can also be applied in the assessment of a potential hydrocarbon discovery of desired minimal volume and its value in any virtual currency like risk-neutral dollars. Such methodology has been extensively developed in the last decades in the Croatian subsurface, mostly in the Croatian part of the Pannonian Basin System (CPBS). Through the adaptation of geological categories, it was also applied in hybrid, i.e., stochastical, models developed in the CPBS (Drava Depression). Stochastically estimation of porosity was already applied. As the robustness of this methodology is very high, it was also modified to estimate the influence of water-flooding in increasing oil recovery in some proven Neogene sandstone reservoirs in the CPBS (Sava Depression). This new modification is being presented to be applied to geological risk calculation, intending to assess the safety of geological environment in deep wells, where depleted radioactive fuel would be disposed, a subject of great importance. The case study encompassed the magmatic and metamorphic rocks in the pre-Neogene basement of the CPBS. For disposal purpose, these are regionally lithologies considered as to be the safest ones considering petrophysical values, water saturation, recent weathering and tectonic activity.

For any odd positive integer $x$, define $(x_n)_{n\geqslant 0} $ and $(a_n )_{n\geqslant 1} $ by setting $x_{0}=x, \,\, x_n =\cfrac{3x_{n-1} +1}{2^{a_n }}$ such that all $x_n $ are odd. The 3x+1 problem asserts that there is an $x_n =1$ for all $x$. Usually, $(x_n )_{n\geqslant 0} $ is called the trajectory of $x$. In this paper, we concentrate on $(a_n )_{n\geqslant 1} $ and call it the E-sequence of $x$. The idea is that, we consider any infinite sequence $(a_n )_{n\geqslant 1} $ of positive integers and call it an E-sequence. We then define $(a_n )_{n\geqslant 1} $ to be $\Omega-$convergent to $x$ if it is the E-sequence of $x$ and to be $\Omega-$divergent if it is not the E-sequence of any odd positive integer. We prove a remarkable fact that the $\Omega-$divergence of all non-periodic E-sequences implies the periodicity of $(x_n )_{n\geqslant 0} $ for all $x_0$. The principal results of this paper are to prove the $\Omega-$divergence of several classes of non-periodic E-sequences. Especially, we prove that all non-periodic E-sequences $(a_n )_{n\geqslant 1} $ with $\mathop {\overline {\lim } }\limits_{n\to \infty } \cfrac{b_n }{n}>\log _23$ are $\Omega-$divergent by using the Wendel's inequality and the Matthews and Watts's formula $x_n =\cfrac{3^n x_0 }{2^{b_n }}\prod\limits_{k=0}^{n-1} {(1+\cfrac{1}{3x_k })} $, where $b_n =\sum\limits_{k=1}^n {a_k } $. These results present a possible way to prove the periodicity of trajectories of all positive integers in the 3x + 1 problem and we call it the E-sequence approach.

The majority of E-commerce transactions reveal private information such as customers' identities, order contents, and payment information during the transaction. Other personal information such as health conditions, religion, and even ethnicity may be also deduced. Even when deploying electronic cryptocurrencies such as Bitcoin, anonymity cannot be fully guaranteed. Also, many anonymous payment schemes suffer from possible double spending circumstances. E-commerce privacy is basically a difficult problem as it involves parties with concurring interests. Three major e-commerce requirements are highly difficult to resolve: anonymous purchase, anonymous delivery, and anonymous payment. This work presents a possible e-commerce system addressing all three anonymity requirements for electronic-items business on open networks. The system offers anonymous entities authentication mechanisms up to completing a fair anonymous e-commerce transaction. The system is based on deploying a physically clone-resistant hardware token for each relevant involved party. The tokens are made clone-resistant by accommodating a Secret Unknown Cipher (SUC) in each hardware-token as a digital PUF-like identity. A set of novel generic system-setups for units, protocols and e-commerce schemes is introduced. The proposed anonymization is basically attained by virtually-replacing relevant e-commerce entities by low-cost, unique and clone-resistant tokens/units using SUCs. The units act as trustable anonymous, authenticated and non-replaceable entities monitored by their acting users.

Recently, the amount of waste generated has been rapidly increasing, there have been difficulties disposing of waste in Korea. As a solution to this, treating waste using a cement kiln has suggested, but the environmental and economic effects have not been specifically studied. In this study, the effects of alternative resources, and reducing the social costs(Installation and Operation) associated with waste treatment facilities were analyzed. Through a co-processing method, a reduction of approximately 53kg of CO2 can be realized during the production of one ton of cement, and cost savings of about 3,815 milion USD. Another effect is an extension of the expiration date for landfills by 7.55 years.

Iron and chromium based alloys have found wide application in various fields of science and technology. Primary carrier based on Fe-Cr-Al alloy is used in block catalysts for high-temperature hydrocarbon conversion, in production of block metal catalysts for neutralization of toxic gases released during operation of internal combustion engines, as well as those present in smoke emissions from enterprises. Influence of thermal action on Fe-Cr-Al alloy foil and stability of secondary carrier on its surface was studied. Elemental composition of the surface layer of X15U5 alloy foil does not remain constant during heating and depends on the thermal treatment mode. Some of the elements come to surface and elemental composition of surface layer can differ significantly from that observed in the bulk of foil sample. This implies the possibility of changing the adhesive and adsorption properties of the foil surface, as well as the need to take this fact into account when supporting a secondary carrier and active phase to the foil. Applied technique of phosphating and supporting a secondary carrier to the foil surface makes it possible to obtain a sufficiently stable coating. There is no shedding of the secondary carrier from foil surface during high-temperature treatment in air.

Composting is one of the most economical and environmentally safe methods of recycling organic waste. Soil microorganisms play a significant role in decomposition and the availability of plant nutrients. This study was designed to prepare a suitable microbial inoculum and its evaluation on composting heap to decrease the time of waste degradation. The bacteria were isolated and molecular characterized from the soil near composting area by using 16S ribotyping technique. The identified strains of bacillus cereus used as an inoculum gives better results to expedite the degradation of organic waste. The prepared bacterial inoculum with molasses was also compared with commercial inoculum by optimizing physical and chemical parameters (temperature, oxygen, C: N, pH, and moisture content) of composting heap. Monthly reading of these parameters was taken from experimental and control treatments. The highest decomposition rate of organic waste was recorded in treatment A (experimental heap) where molasses and bacterial inoculum were added and less decomposition was observed in treatment D (experimental heap) where no inoculum and molasses were added. It was concluded from the studies that the prepared bacterial inoculum with two strains of Bacillus was effective and prepared mature compost in 2.5 months by increasing decomposition efficiency of organic waste. Furthermore, the prepared compost was also sustainable in its physical and chemical characteristic.

More than 800 million tons of fish are utilizing in a year and 25-30% become waste. The waste amount is beneficial source for extraction of collagen. But procedure of extraction is still to be optimized. The current study was designed to extract collagen from fish through fish waste fermentation under various conditions. For collagen extraction we did lactic acid fermentation in which yogurt and Dough bacteria was added with fish sample and placed it in incubator at 30ºC for one month. In yogurt and dough culture have at least 10 type of lactic acid bacterial species. After every week we check PH of each sample and take soup of that sample. After centrifugation of that sample’s TCA (Trichloroacetic acid) precipitation was done of yogurt and dough sample and kept at -20ºC. then did SDS-PAGE) using 6% resolving and 5% stacking gel of already stored sample. Then HaCaT cells (1 × 10⁴ cells/well) were cultured in 96-well flat-bottom culture plates and treated with appropriate doses of FFCP (fermented fish collagen peptide) for 24 and 48 hours.The SDS-PAGE revealed that the collagen protein of fish had doublet pattern for α1 and α2 chains at corresponding to 145 kDa and 132 kDa respectively. The density for α1 twice as compared to α2. Our result agrees that The fish collagen consists mostly of α-chain as well as little amount of inter and intra molecular cross-linked components of α-chains; b (dimmer) and c (trimer). Different biochemical tests were done for identification of lactic acid bacteria catalase positive, citrate positive, urease negative. Our fermented fish collagen and peptides mixture were test for cellular cytotoxicity and proliferative effect on HaCaT cells. Current result shows that fermented extracted collagen are nontoxic and induce the proliferation of HaCaT cells. Current study is supported by various studies that revealed the medical application of fish extracted collagen as underline.

The situation in the world of pandemics is rapidly changing, and the second wave of COVID-19 has put a lot of pressure on the government and private sector, which are primarily responsible for controlling the situation. COVID-19 positive cases have increased in recent months relative to last year, and the number of patients admitted to hospitals has also increased, despite the fact that few of them were denied admission due to shortage of beds. Normal people who experience any symptoms immediately isolate themselves and begin taking the COVID medications prescribed by medical personnel and their team. During these times, all domestic people tossed the wrappers and boxes of medicines into the regular trash can, and the waste was handed over to the waste collector, who treated it like any other domestic waste and disposed of it using open dumping or other methods. The goal of this perspective is to suggest the collections of these types of waste from domestics, and protect the natural resources like water, soil, and even living beings like animals from pollution (from the effect of SARS-CoV-2). The main challenge for environmental waste management agencies is determining who has COVID positive and which houses generate these types of waste; thus, proposed strategy may be beneficial to the long-term sustainability of natural resources and animals.

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil (WCO). Quality parameters such as the acid value, water content, and free and total glycerin content were evaluated and compared with those of commercial resins such as Magnesol® and Amberlite™. Promising results were obtained using sawdust during the purification process, achieving a 31.6% reduction in the acid value compared to that of unpurified biodiesel, the reduction was 31.3% more efficient than Amberlite™. Sawdust adsorbed free glycerin at 55.8%, being more efficient than Amberlite™. The total glycerin values were similar between commercial resins and sawdust. A water content values were similar than Amberlite™ and better than that with Magnesol®, at 4.3% and 39.81%, respectively. These results show that sawdust can be used as an alternative bioadsorbent in a dry purification method for biodiesel being a residue with less environmental impact.

This preprint is focused in the presence of plastics and microplastics in food. We will discuss how many we eat, and how they arrive to the food, and why. We will treat many other things, such as the waste treatment in Europe and in Spain, with updated data; how much plastic waste is generated; what are microplastics and how they are analyzed, I will tell about the experience we have at the University of Alicante (UA); how they can be removed and we will estimate how many we eat over the course of a year.

Mining is one of the main economic activities of several developing countries as Chile. Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased that has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium and rare earth elements. This transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid-liquid separation that allows the processing of solutions with low concentrations of metals corresponds to the adsorption, and more recently the biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in the different types of biomass. Bacterial, fungal, plant and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit in the north of Chile and after an acid leaching copper was biosorbed, for which the kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH and initial metal concentration were studied.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

One of the biggest problems that the Dominican Republic has had in recent decades is the efficient management of solid waste produced by the population. This problem has worsened in recent years due to the decrease in available areas for the construction of sanitary landfills, the lack of recycling culture in the population, the deficiency in waste collection, and the scarce legal controls aimed at preserving water and air and soil, among other factors. The objective of this study was to explore the management of solid waste by the population and the municipality of Puñal, province of Santiago, to evaluate and analyze the situation and generation of solid waste, municipal solid waste management services, and the attitudes of the population regarding recycling projects and waste management, to evaluate the viability and sustainability of the use organic waste for energy generation. A total of 275 households from 29 localities in the municipality of Puñal were surveyed, which allowed for a significant population sample. According to the results obtained, the most significant type of waste produced by families is organic waste, followed by plastic waste and paper. Of the total organic waste produced in the municipality, 53% of solid waste is disregarded through the municipal waste collection system, while 47% is used as plant fertilizers or animal feed. On the other hand, most households receive the municipal waste collection service and pay for this service. The results of our research show that the implementation of an energy production system based on organic waste would be viable in the municipality of Puñal. However, a more efficient waste collection system would be necessary and the development of programs and projects that allow all households to participate in the system.

Background: In the 2022 National Youth Tobacco Survey disposable e-cigarette devices are shown to be the most widely used e-cigarette devices amongst U.S. youth. In this paper we report the results of research designed to estimate the prevalence of use of BIDI® Stick branded e-cigarettes amongst youth (aged 13 to 17), and under-age young adults (aged 18 to 20) in the U.S. Methods: Cross sectional online survey of a nationally representative sample of 1,215 youth (13 17 years) recruited via the IPSOS probability-based KnowledgePanel and 3,370 young adults aged 18 to 24 - amongst whom 1,125 were aged 18 to 20. Results: Amongst youth aged 13 to 17, 0.91% [95% CI: 0.44-1.68] or 190,000 [95% CI: 90,000-350,000] youth reported having ever used a BIDI® Stick branded product and 0.04% [95% CI: 0.00-0.38] or less than 10,000 youth reported currently using a BIDI® Stick branded product. Amongst those young adults aged 18 to 20, 3.90% [95% CI: 2.49-5.81] or 470,000 [95%CI: 300,000-700,000] reported having ever used a BIDI® Stick product whilst 0.60% [95% CI: 0.17-1.55] or 70,000 [95% CI: 20,000-180,000] reported they now use a BIDI® Stick product “every day” or “some days”. Conclusions: The low prevalence of youth and underage adult current use of the BIDI® Stick e cigarette suggests that this product is not responsible for the recent growth in the use of disposable e-cigarettes by youth within the U.S. as demonstrated by the 2022 National Youth Tobacco Survey.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

Metabolites are essential intermediate products in metabolism, and metabolism dysregulation indicates different types of diseases. Previous studies have shown that cigarette smoke dysregulated metabolites; however, limited information is available with electronic cigarette (E-cig) vaping. We hypothesized that E-cig vaping and cigarette smoking altered systemic metabolites, and we propose to understand the specific metabolic signature between E-cig users and cigarette smokers. Plasma from non-smoker controls, cigarette smokers, and e-cig users were collected, and metabolites were identified by UPLC–MS (Ultraperformance liquid chromatography-mass spectrometer). Nicotine degradation was activated by e-cig vaping and cigarette smoking with increased concentrations of cotinine, cotinine N-oxide, (S)-nicotine, and (R)-6-hydroxynicotine. Additionly, we found significant decreased concentrations in metabolites associated with tricarboxylic acid (TCA) cycle pathways in e-cig users verses cigarette smokers, such as: D-glucose, (2R,3S)-2,3-dimethylmalate, (R)-2-hydroxyglutarate, O-phosphoethanolamine, malathion, D-threo-isocitrate, malic acid, and 4-acetamidobutanoic acid. Cigarette smoking significant up-regulated sphingolipid metabolites, such as D-sphingosine, ceramide, N-(octadecanoyl)-sphing-4-enine, N-(9Z-octadecenoyl)-sphing-4-enine, and N-[(13Z)-docosenoyl]sphingosine, verses e-cig vaping. Overall, e-cig vaping dysregulated TCA cycle realted metabolites while cigarette smoking altered sphingolipid metabolites. Both e-cig and cigarette smoke increased nicotinic metabolites. Therefore, specific metabolic signature altered by e-cig vaping and cigarette smoking could serve as potential systemic biomarkers for early cardiopulmonary diseases.

In the recent century, the tourism industry and within it the tourism economy are one of the most important and fundamental sectors of engaged business. E-tourism can be used as a dynamic tool in up to date areas of informative information and tourism marketing will be considered as a suitable field for the tourism industry. The aim of this study was to investigate the relationship between climate change and the amount of revenues from the tourism industry relying on a tool called e-tourism, and informing and providing services through this way so that Iran can achieve a greater share of export of a single-product oil economy combined with economic growth and sustainable development goals. The method of this research is descriptive-analytical.

The purpose of this study is to find out the e-reputation management of the hotel industry, as well as the social media channels used as the tools of hotel e-reputation building. This study used a qualitative approach by analyzing the in-depth interviews with hotel marketing communication practitioners of 15 hotel companies in Bandung City. The findings identified that e-reputation is considered a crucial factor in determining hotel performance due to the change of customers’ behaviors today and identified also three types of e-reputation management activities implemented by hotel companies, such as online activities, offline activities, and online/offline activities. The results of this study have implications for the hospitality industry, as a reference for formulating their marketing strategies.

From professors overwhelmed by anxiety-driven e-mails from students, through faculty and administrative staff wasting valued time on e-mail minutia, misuse of electronic mail in the academy has become ubiquitous. After a brief overview of the unique features of e-mail communication, this study provides insight and guidelines to plan new educational activities on healthy and productive utilization of e-mail in the academy of the digital era. The overall aim is to prioritize scholarly deep work by focusing on teaching and research work, freeing working time wasted on unproductive use of e-mail.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use

Health care workers (HCWs), specifically dentists, are at the front line for acquiring blood-borne virus infections. The highest proportion of occupational transmission is through percutaneous injuries via hollow-bore needles. Several studies around the world have reported that hepatitis viruses and human immunodeficiency virus are the main pathogens for most cases of occupationally acquired blood-borne infection. We aim to investigate the prevalence of hepatitis B virus (HBV), hepatitis C virus (HCV), hepatitis E virus (HEV), and human immunodeficiency virus (HIV) among Mexican dentists. Methods. We included 159 dentists who attended the annual meeting at the Medica Sur Clinic & Foundation held in Mexico City in May 2016. A survey was applied in order to obtain data of occupational exposure to blood-borne viruses (BBV). Serum samples were screened serologically using enzyme-linked immunosorbent assays. Results. Two dentists (1.2%) were positive for antibodies against HCV antigen, one (0.6%) was positive for antibodies against HBV antigen and three (1.8%) were positive for the detection of IgG antibodies against HEV. Two cases (1.2%) were positive for antibodies against HIV. Conclusions. The infection by HEV was the most prevalent among dentists. However, the prevalence of BBV in dentists was similar to that in the general population.

Excessive production, consumption and indiscriminate disposal of plastic waste cause an increasing plastic pollution with detrimental impacts on environment and human health. This study aimed to assess the level of knowledge, attitude, and practices (KAP) towards plastic pollution among Malaysians and evaluate the variation of plastic pollution related KAP among various socio-demographics. An online survey was conducted, and 294 valid responses was obtained. Descriptive statistics, KAP scoring and cross tabulation of responses were estimated. One-way analysis of variance, paired t-test and binary logistic regressions were carried out. Results showed that respondents had poor knowledge (mean 7.41 ± 1.80) and practice score (3.81 ± 1.39) across all socio-demographics. Compared to younger (18-30 years) respondents, older ones (>46 years) had higher knowledge (odds ratio, OR 4.304; p<0.01). However, middle aged (31-45 years) respondents reported significantly (p<0.01) higher attitude (OR 4.019) and practice (OR 4.056; p <0.05). Respondents with environmental related university education had showed higher odds about plastic pollution related knowledge (OR 10.343; p<0.01). Suggestions are made to undertake interventions such as environmental awareness creation, incorporating plastic pollution topics in formal and informal education, and providing recycling facilities nearby the localities for encouraging good practices towards minimizing plastic uses and pollution.

In this paper, the authors identified key elements important for circularity: (1) Background: The primary goal of circularity is to eliminate waste and to prove the constant use of resources. In the paper, we classify studies according to circular approaches. The authors identified main elements and classified them into categories important for circularity, starting with the managing and reducing waste and the recovery of resources; and ending with the circularity of material, and general circularity-related topics and presented scientific works dedicated to each of the above-mentioned categories. The authors analyzed several core elements from the first category aiming to investigate and connect different waste streams and provided a regression model; (2) Methods: The authors used a dynamic regression model to identify relationships among variables and selected the ones, which has an impact on the increase of biowaste. The research was delivered for the 27 European Union countries during the period between 2020 and 2019; (3) Conclusions: The authors indicated that the recycling rate of wasted electrical equipment in the previous year has an impact on the increase of recycling biowaste next year. This is explained as non-metallic spare parts of electronic equipment are used as biowaste for fuel production. And the separation process of the composites of electric equipment takes some time, on average the effect is evident in one year period.

COVID-19 greatly challenges human beings in the health sector and leaves behind a large amount of medical waste that poses many potential threats to the environment. In this paper, we compiled relevant data released by official agencies and the media, and conducted data supplementation based on previous studies to calculate the net value of medical waste production in Hubei Province during COVID-19 with the help of a neural network model. Then, we reviewed the data related to the environmental impact of medical waste per unit and designed four scenarios to estimate the environmental impact of new medical waste generated during the epidemic. The results showed that at a medical waste generation rate of\ 0.\ 5\ kg/(\ bed\ \cdot\ d) COVID-19 resulted in a net increase in medical waste volume of about 3366.99 tons in Hubei Province. In the four scenario assumptions, if the medical waste brought by COVID-19 is completely incinerated, it will have a large impact on the air quality. If it is disposed by distillation sterilization, it will produce a large amount of wastewater and waste residue. Based on the results of the study, three policy recommendations are proposed in this paper: strict control of medical wastewater discharge, reduction and transformation of the emitted acidic gases, and attention to the emission of metallic nickel in exhaust gas and chloride in soil. These policy recommendations provide a scientific basis for controlling medical waste pollution.

Sherubtse College under Royal University of Bhutan has a total of 1582 students, where 787 0f them are female. They suffer from menstrual and menstrual cramps every month and they use napkins to stay clean and healthy. As all the college girls are educated on the norms and use of sanitary napkins, the proper management of the waste generated is lacking. The disposal of used sanitary napkins and management is a challenge to the college management. This small research aims to investigate on how girls in college campus manage the menstural waste and the amount of sanitary napkins used. The lack of proper dumping areas leads to the improper sanitary waste management and sometimes the waste generated from the sanitary napkins are toxic and unhealthy. It is very important to initate some ways to dump the pads and its related problem should be seriously addressed by the college management. It is also important to come up with different soultion and management of these wastes for sustainable environment. Therefore, this research will be mainly mentioning about the suggestions and how the sanitary waste is being managed in Sherubtse College campus and the amount of sanitary pads used in a month or an year.

In no-tillage systems, there is an accumulation of crop residues (CR) which plays an important role in available of soil-N. A study was set up to provide information regarding the CR N credit, and the influence of N mineral fertilizer. An incubation was run in a loam soil with addition of a similar rate of residue (10 Mg ha-1; sugarcane, soybean, and brachiaria) and N mineral fertilizer (urea; 120 kg N ha-1). After the stabilization of biological activity, soil and remaining residues were collected, and N monitored. Results showed that the N credit was positive with application of soybean, sugarcane, and brachiaria. There was an expressive performance of soybean N credit represented by a positive balance, and a reduction from 2.49 to 0.9 g kg-1 of N in residue, with direct increase of 90% of soil-N. There is no need of N fertilizer to potentialize the soybean N credit, but it is requested to potentialize N credit of brachiaria and sugarcane. The urea demonstrated be a good enhancer of brachiaria N credit, but it was not adequate to sugarcane residues. Based in our result, the accumulation and incorporation of CR can be considered as a N credit with positive contribution in soil-N.

A shrimp oil rich in omega-3 lipids and carotenoids is obtained in remarkably high 5 wt% yield extending to pink shrimp processing waste (head and carapace) the circular economy approach to extract fish oil from fish processing by-products using d-limonene. Biobased limonene, a powerful antimicrobial and antioxidant agent, is an excellent solvent for both lipids and astaxanthin-based carotenoids preventing oxidative degradation during the extraction cycle including solvent and oil separation at 85°C. A new low cost route is established to extract valued marine oil from biowaste annually made available in over 2.2 million tonnes.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

In the European Union, the demand for polyurethane is continually growing. In 2017, the estimated production value of polyurethane was 700,400T, of which 27.3% is taken to landfill, which causes an environmental problem. In this paper the behaviour of various polyurethane foams from the waste of different types of industries will be analysed with the aim of assessing their potential use in construction materials. In order to this, the wastes were chemically tested by means of CHNS, TGA, and leaching tests. They were tested microstructurally by means of SEM. The processing parameters of the waste was calculated after finding out its granulometry and its physical properties i.e. density and water absorption capacity. In addition, the possibility of incorporating these wastes in plaster matrices was studied by determining its rendering in an operational context, finding out its mechanical resistance to flexion and compression at 7 days, its reaction to fire as well as its weight per unit of area and its thermal behaviour. The results show that in all cases, the waste is inert and does not undergo leaching. The generation process of the waste determines the foam’s microstructure in addition to its physical-chemical properties that directly affect building materials in which they are included, thus offering different ways in which they can be applied.