Background: The t (2; 5) chromosomal rearrangement and resulting nucleophosmin (NPM1) -ALK fusion was first observed in 1994 in anaplastic large cell lymphoma (ALCL), a T-cell lymphoma responsive to cyclophosphamide, abriblastine, vincristine and prednisone in approximately 80% of cases; refractory cases usually respond favorably to brentuximab-vedotin. These treatments are regarded as a bridge to allogeneic hematopoietic stem cell transplantation (allo-SCT). Nowadays, transplant procedures and monitoring of chemotherapy patients proceed very slowly because the SARS-CoV-2 pandemic has heavily clogged the hospitals in all countries. Results: A 40-year-old Caucasian woman was first seen at our clinical center in June 2020. She had ALCL ALK +, a history of failure to two previous therapeutic lines and was in complete remission after 12 courses of Brentuximab, still pending allo-SCT after two failed donor selection. Facing of a new therapeutic failure, we requested the Italian drug regulatory agency, and obtained the authorization, to administer 250 mg twice a day of Crizotinib, a drug incomprehensibly not registered for ALCL ALK +. Conclusions: The response to Crizotinib was optimal, since no adverse event occurred, and CT-PET persisted negative; this drug has proved to be a valid bridge to allo-SCT

In recent decades, widespread damage to structures due to destructive earthquakes has encouraged researchers to use seismic control systems. One of the most important structures is bridges, which should maintain their service after severe earthquakes. One of the ways to control the bridge is to isolation the deck from the substructure, which results in high displacements at different points in the bridge and the residual displacements within the separator itself, thus requiring repair and replacement of these systems after severe earthquakes. Therefore, the use of new seismic separation systems on bridges has always been important. The purpose of this project is to utilize a new memory-shaped seismic separator system to investigate the seismic performance of v-shaped column bridges , in which case the effect of earthquake orientation and its effects on responses the earthquake will also be assessed. Due to the ever-increasing advances in various intelligent materials, such as shape memory alloys, and their unique capacities, such as back-centering, and high fatigue and corrosion resistance, in this study, these materials have been used as a complementary component along with lead core separators. The shape memory alloy has been used as 4 vertical rods that connect two separating parts to each other and in this research the diameter and location of these rods will be calculated using optimization algorithm in Matlab software.

Many various using of this new-born fuzzy model for solving real-world problems and urgent requirements involve introducing new concept for analyzing the situations which leads to solve them by proper, quick and ecient method based on statistical data. This gap between the model and its solution cause that we introduce nikfar domination in neutrosophic graphs as creative and eective tool for studying a few selective vertices of this model instead of all ones by using special edges. Being special selection of these edges aect to achieve quick and proper solution to these problems. Domination hasn't ever been introduced. So we don't have any comparison with another denitions. The most used graphs which have properties of being complete, empty, bipartite, tree and like stu and they also achieve the names for themselves, are studied as fuzzy models for getting nikfar dominating set or at least becoming so close to it. We also get the relations between this special edge which plays main role in doing dominating with other special types of edges of graph like bridges. Finally, the relation between this number with other special numbers and characteristic of graph like order are discussed.

Scouring is the most common cause of bridge failure. This study was conducted to evaluate the efficiency of the Artificial Neural Networks (ANN) in determining scour depth around composite bridge piers. The experimental data, attained in different conditions and various pile cap locations, were used to obtain the ANN model and to compare the results of the model with most well-known empirical, HEC-18 and FDOT, methods. The data were divided into training and evaluation sets. The ANN models were trained using the experimental data, and their efficiency was evaluated using statistical test. The results showed that to estimate scour at the composite piers, feedforward propagation network with three neurons in the hidden layer and hyperbolic sigmoid tangent transfer function was with the highest accuracy. The results also indicated a better estimation of the scour depth by the proposed ANN than the empirical methods.

This paper proposes a method for determining the bridge condition index (BCI) in concrete bridges, which is based on the views of bridge experts. First, eight indices were defined for a concrete bridge including structure, hydrology, safety, load impact, geotechnical and seismicity, strategic importance, facilities, and finally traffic and pavement. Each index consists of several sub-indices. Next, a series of questionnaires about the relative importance of indices and their sub-indices were prepared and distributed among bridge experts. Experts’ views were analyzed by Expert Choice software and the relative importance (weight) of each index and each sub-index was determined using the analytical hierarchy process (AHP). Then, based on experts’ views, an average score was assigned to each sub-index for any condition. Now the bridge inspectors can examine the bridge and determine the scores of sub-indices. Each index’s score is the sum of the weighted score assigned to its’ sub-indices and BCI is the sum of weighted scores assigned to indices. Higher values of BCI indicate a better condition. Therefore, bridges with lower BCI take priority in maintenance activities. To apply the proposed method, five bridges were selected in Semnan province, Iran, and BCI calculation of these bridges were conducted.

The aim of this expository article is to present recent developments in the centuries-old discussion on the interrelations between several types of domination in graphs. However, the novelty even more prominent in the newly discovered simplified presentations of several older results. Domination can be seen as arising from real-world application and extracting classical results as first described by this article.The main part of this article, concerning a new domination and older one, is presented in a narrative that answers two classical questions: (i) To what extend must closing set be dominating? (ii) How strong is the assumption of domination of a closing set? In a addition, we give an overview of the results concerning domination. The problem asks how small can a subset of vertices be and contain no edges or, more generally how can small a subset of vertices be and contain other ones. Our work was as elegant as it was unexpected being a departure from the tried and true methods of this theory that had dominated the field for one fifth a century. This expository article covers all previous definitions. The inability of previous definitions in solving even one case of real-world problems due to the lack of simultaneous attentions to the worthy both of vertices and edges causing us to make the new one. The concept of domination in a variety of graphs models such as crisp, weighted and fuzzy, has been in a spotlight. We turn our attention to sets of vertices in a fuzzy graph that are so close to all vertices, in a variety of ways, and study minimum such sets and their cardinality. A natural way to introduce and motivate our subject is to view it as a real-world problem. In its most elementary form, we consider the problem of reducing waste of time in transport planning. Our goal here is to first describe the previous definitions and the results, and then to provide an overview of the flows ideas in their articles. The final outcome of this article is twofold: (i) Solving the problem of reducing waste of time in transport planning at static state; (ii) Solving and having a gentle discussions on problem of reducing waste of time in transport planning at dynamic state. Finally, we discuss the results concerning holding domination that are independent of fuzzy graphs. We close with a list of currently open problems related to this subject. Most of our exposition assumes only familiarity with basic linear algebra, polynomials, fuzzy graph theory and graph theory.

New York State Department of Transportation designates potentially hazardous conditions on bridges as flags. From 1982 until 2006 the flags issued for the bridges owned by New York City underwent all phases typical of crises, including a gradual increase, an exponential expansion, an extended peak, a gradual decline, and a convergence to a higher but manageable level. The attempts to forecast the flag pattern as it was developing are reviewed for possible relevance to management of the transportation infrastructure and in general.

The stiffness of the myosin cross-bridges is a key factor in analysing possible scenarios to explain myosin head changes during force generation in active muscles. The seminal study of Huxley and Simmons (1971: Nature 233: 533) suggested that most of the observed half-sarcomere instantaneous compliance (=1/stiffness) resides in the myosin heads. They showed with a so-called T₁ plot that, after a very fast release, the half-sarcomere tension reduced to zero after a step size of about 60Å (later with improved experiments reduced to 40Å). However, later X-ray diffraction studies showed that myosin and actin filaments themselves stretch slightly under tension, which means that most (at least two-thirds) of the half sarcomere compliance comes from the filaments and not from cross-bridges. Here we have used a different approach, namely to model the compliances in a virtual half sarcomere structure in silico. We confirm that the T₁ curve comes almost entirely from length changes in the myosin and actin filaments, because the calculated cross-bridge stiffness (probably greater than 0.4 pN/Å) is higher than previous studies have suggested. In the light of this, we present a plausible modified scenario to describe aspects of the myosin cross-bridge cycle in active muscle. In particular, we suggest that, apart from the filament compliances, most of the cross-bridge contribution to the instantaneous T₁ response comes from weakly-bound myosin heads, not myosin heads in strongly attached states. The strongly attached heads would still contribute to the T₁ curve, but only in a very minor way, with a stiffness that we postulate could be around 0.1 pN/Å, a value which would generate a working stroke close to 100 Å from the hydrolysis of one ATP molecule. The new program can serve as a tool to calculate sarcomere elastic properties for any vertebrate striated muscle once various parameters have been determined (e.g. tension, T₁ intercept, temperature, X-ray diffraction spacing results).

We introduce a new variation on the domination theme which we call vertex domination as reducing waste of time in transportation planning and optimization of transport routes. We determine the vertex domination number $\gamma_v$ for several classes of fuzzy graphs. The bounds is obtained for it. In fuzzy graphs, monotone decreasing property and monotone increasing property are introduced. We prove both of the vizing's conjecture and the Grarier-Khelladi's conjecture are monotone decreasing fuzzy graph property for vertex domination. We obtain Nordhaus-Gaddum (NG) type results for these parameters. The relationship between several classes of operations on fuzzy graphs with the vertex domination number of them is studied. Finally, we discuss about vertex dominating set of a fuzzy tree by using the bridges and $\alpha$-strong edges equivalence.

Molecular motors play a vital role in the transport of material within the cell. A family of motors of growing interest are burnt bridge ratchets (BBRs). BBRs rectify spatial fluctuations into directed motion by creating and destroying motor-substrate bonds. It has been shown that the motility of a BBR can be optimized as a function of the system parameters. However, the amount of energy input required to generate such motion and the resulting efficiency has been less well characterized. Here, using a deterministic model, we calculate the efficiency of a particular type of BBR, namely a polyvalent hub interacting with a surface of substrate. We find that there is an optimal burn rate and substrate concentration that leads to optimal efficiency. Additionally, the substrate turnover rate has important implications on motor efficiency. We also consider the effects of force-dependent unbinding on the efficiency and find that under certain conditions the motor works more efficiently when bond breaking is included. Our results provide guidance for how to optimize the efficiency of BBRs.

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

It is challenging to apply heat flow through a thermal bridge, which requires the analysis of 2D or 3D heat transfer to building energy simulation(BES). Research on the dynamic analysis of thermal bridges has been underway for many years, but their utilization remains low in BESs. This paper proposes a thermal bridge modeling and a dynamic analysis method that can be easily applied to BESs. The main idea begins with an analogy of the steady-state analysis of thermal bridges. As with steady-state analysis, the proposed method first divides the thermal bridge into a clear wall, where the heat flow is uniform, and the sections that are not the clear wall (the thermal bridge part). For the clear wall part, the method used in existing BESs is applied and analyzed. The thermal bridge part (TB part) is modeled with the linear time-invariant system (LTI system) and the system identification process is performed to find the transfer function. Then, the heat flow is obtained via a linear combination of the two parts. This method is validated by comparing the step, sinusoidal and annual outdoor temperature response of the finite differential method(FDM) simulation. When the thermal bridge was modeled as a third-order model, the root mean square error(RMSE) of annual heat flow with the FDM solution of heat flow through the entire wall was about 0.1W.

One new cassane diterpene possessing an unusual N bridge between C-19 and C-20 named caesalsappanin R (1), as well as another new diterpene caesalsappanin S (2), were isolated from the seeds of Caesalpinia sappan with methanol extract. Their structures were determined by spectroscopic analysis and examined alongside existing data from prior studies. Their biological activities were profiled by their antiplasmodial activity.

In this review, photoinduced electron transfer processes in specifically designed assembled ar-chitectures have been investigated on the basis of recent results reported from our laboratories. A convenient and useful way to study these kinds of systems has been described in order to under-stand the rules that drive to a light induced charge separation and its subsequent decay to the ground state, also with the aim of offering a tutorial for young researchers. Assembled systems of covalent or supramolecular nature have been presented and some functional multicomponent systems for the conversion of light energy into chemical energy have been discussed.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

Zebrafish have been found to be the premier model organism in biological and biomedical research, specifically offering many advantages in developmental biology and genetics. This unique aquatic species has been found to have the capacity to regenerate their spinal cord after injury. However, the complete molecular and cellular mechanisms behind glial bridge formation in the central and peripheral nervous systems upon glial cell injury remains unclear. This review paper focuses on the molecular mechanisms and cellular processes that underlie spinal cord regeneration in four initial phases: proliferation and initial migration; migration and differentiation; glial bridge formation; and remodeling. We propose that within these four phases the cellular mechanisms that underlie spinal cord regeneration each express a terminating signal that aborts one step of the process and initiates the next. Specifically, future studies would be devoted to investigate transmitting signals in the spinal cord injury micro-environment in hope to contribute to the understanding of underlying cellular mechanisms by connecting each process of spinal cord regeneration in zebrafish.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

For the first time, We do fuzzification the concept of domination in crisp graph on a generalization of fuzzy graph by using membership values of vertices, α-strong edges and edges. In this paper, we introduce the first variation on the domination theme which we call vertex domination. We determine the vertex domination number γ_v for several classes of t-norm fuzzy graphs which include complete t-norm fuzzy graph, complete bipartite t-norm fuzzy graph, star t-norm fuzzy graph and empty t-norm fuzzy graph. The relationship between effective edges and α-strong edges is obtained. Finally, we discuss about vertex dominating set of a fuzzy tree with respect to a t-norm ⨂ by using the bridges and α-strong edges equivalence.

An informative probe of myosin crossbridge behaviour in active muscle is a mechanical transient experiment where, for example, a fully active muscle initially held at constant length is suddenly shortened to a new fixed length giving a force transient, or has its load suddenly reduced giving a length transient. We describe the simplest crossbridge mechanical cycle we could find to model these transients. We show using the statistical mechanics of 50,000 crossbridges that a simple cycle with two actin-attached cross-bridge states, one producing no force and the other producing force, will explain much of what has been observed experimentally and we discuss the implications of this modelling for our understanding of how muscle works. We show that this same simple model will explain reasonably well the isotonic mechanical and X-ray transients under different loads observed by Reconditi et al (2004, Nature 428, 578) and that there is no need to invoke different crossbridge step sizes under these different conditions; a step size of 100 Å works well for all loads. We do not claim that this model provides a total mechanical explanation of how muscle works. But we do suggest that only if there are other observations that cannot be explained by this simple model should something more complicated be considered.

The generation of vortices around bridge piers can lead to removal of riverbed materials from around piers, especially during flood events and heavy rainfalls, which can compromise the stability of the bridge and consequently its failure, if not properly detected and mitigated. Bridge failures pose serious threats to the local socio-economic and public safety and can cost lives. As such, real-time monitoring and early warning systems for scour-induced bridge failure can serve as a vital tool to protect the community and civil infrastructure against disastrous events. Vibration-base monitoring of bridge scour is an attractive option due to its low cost and relatively easy installation without the need to block the road and close the bridge to traffic. While limited number of previous studies have shown the capabilities of acceleration-based monitoring techniques in this area of research, they generally lack a rigorous framework for data analysis within and relating those to evaluate scour. This paper is an attempt to provide such framework that would enable a fast and low-cost analysis of vibration data within a physical modelling study on a simplified bridge pier. To achieve this, three experiments were conducted on an ideal single-pier scaled model bridge in a hydraulic flume, where water flows at a velocity near the critical velocity for the sand bed which in turn generates a scour hole around the pier. Then, the vibration data recorded using two mounted wireless accelerometers, were used to conduct an operational modal analysis through which the natural frequencies are extracted. The extracted natural frequencies and measured scour depths are then used to provide a chart that relates these two parameters. The results of this study showed the promising capability of the vibration-based data analysis in finding this relationship, indicating an up to around 30-50% reduction in natural frequencies as a result of around 50% scour ratio (ratio of maximum scour depth to buried depth), and beyond 50% scour ratio the natural frequencies remain constant. While the data presented in this paper are preliminary, they clearly show a promising potential for application in real-time monitoring of bridge stability under the effect of local scour and further works are underway to enrich the experimental data and empower the proposed methodologies at the laboratory scale.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

The use of polyolefin fibre reinforced concrete (PFRC) as an alternative for reducing or even eliminating the reinforcing steel bars employed in reinforced concrete has become real in the past years. This contribution analyses the improvements in sustainability that a change in the aforementioned reinforcement configuration might provide in a flyover bridge. Economic, environmental and social parameters of both possibilities were studied by means of the integrated value model for sustainable assessment use (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, which is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. The results of the MIVES method showed that the use of PFRC in combination with reinforced concrete (RC) has a sustainability index 22% higher. An analysis of the parameters that form this evaluation shows that there are no remarkable differences in the financial costs between the two possibilities studied. Nevertheless, social and environmental aspects provide with a better qualification the option of building a bridge by using PFRC combined with RC.

This paper proposes a method for monitoring the structural health of concrete bridges in Iran. In this method, the bridge condition index (BCI) of bridges is determined by the analytical hierarchy process. BCI constitutes eight indices that are scored based on the experts' views, including structural, hydrology and climate, safety, load impact, geotechnical and seismicity, strategic importance, facilities, and traffic and pavement. Experts' views were analyzed by Expert Choice software, and the relative importance (weight) of indices were determined using the analytical hierarchy process (AHP). Then, the gave scores of experts were assigned to indices for various conditions. Bridge inspectors can examine the bridge, determine the scores of indices, and compute BCI. Higher values of BCI ​​indicate better conditions. Therefore, bridges with lower BCI take priority in maintenance activities. Five bridges in Iran, Semnan province, were selected as the case studies, and BCI calculation of these bridges was conducted.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

The purpose of the study was to provide support in the decision-making process for architects and engineers regarding large-spans structures for the presentation of archaeological sites in situ - construction of roofs, shelters, and bridges. We examined existing practice and analyzed their engineering classifications looking for a pattern in their application regarding sustainability and relation between type of cultural heritage site and type of applied large span structure. Contemporary engineering structures at built heritage sites create a sharp contrast between old and new. A presentation of cultural heritage in situ requires an understanding of heritage theory and internationally accepted doctrine which exceeds common engineering education. Nevertheless, application of large-span structures, which often take advantages of state-of-art construction-technologies nowadays, is also an aesthetical statement that affects the appearance of the site. Therefore, we gave an overview of the theoretical background of aesthetical issues and the overall ethics of the decision-making process in such sensitive cases. Within the framework of heritage-presentation, engineering and architectural issues, and selected case studies, we concluded in favor of the application of large-span structures under certain conditions.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

Cerebrospinal fluid (CSF)-contacting neurons (CSF-N) located in the surface of both brain ventricles and the central canal (cc) in the spinal cord. The cc and CSF maintain a proliferative niche for neural progenitor cells and play a vital role in development of the brain. The CSF circulates in the ventricles and the subarachnoid spaces with the CSF rhythmic flow: cardiac pulsation and respiratory fluctuation. A new concept of CSF motion may be contrary to the classical one that the direction of CSF motion may vary in direction and may be dynamic in its location. The CSF pressure may also depend on the body position. Moderate music-making has been considered a potential approach for rehabilitative and restorative therapy of brain dysfunctions. Recently, we find that the CSF-Ns are present in both the interior CFS in the cc and also exterior CSF around the surface of the spinal cord. We hypothesize that CSF-N as mechanical sensors in the spinal cord could sense motion of the spinal cord. The myodural bridge is a ligament connecting a pair of deep, upper-neck muscles to the dura mater, which envelops the arachnoid mater and contains the CSF surrounding the brain and the spinal cord. We figure out the term “CSF-static compartment” and classify CSF storage location as rostral pool and caudal pool to demonstrate our hypothesis. We presume that the somatic body movement with music-making and rehabilitation-based interventions would orchestrate the CSF motion with head movement, myodural bridge stretching and puling as well as spinal bending.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

Background: To compare the loss of preload in absence of loading and after a fixed number of ideal masticatory cycles in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400000 masticatory cycles were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400000 masticatory cycles; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 minutes from the tightening in absence of cyclic loadings. Conclusions: MUA and OT-Bridge are reliable prosthetic anchoring systems able to tolerate repeated masticatory cycles also on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening

The coevolution of species drives diversity in animals and plants and contributes to natural selection, whereas in host–parasite coevolution, a parasite may complete an incomplete evolutionary/developmental function by utilizing the host cell’s machinery. Analysis of related older data suggests that Plasmodium falciparum (P. falciparum), the pathogen of malaria tropica, cannot survive outside its human host because it is unable to perform the evolutionarily first protein glycosylation of serologically A-like, O-GalNAcα1-Ser/Thr-R, Tn antigen (“T nouvelle”) formation, owing to its inability for synthesizing the amino sugar N-acetyl-d-galactosamine (GalNAc). This parasite breaks the species barrier via hijacking the host's physiological A-like/Tn formation through abundantly expressing serine residues and creating hybrid A-like/Tn structures, which in the human blood group O(H) are attacked by the germline-encoded nonimmune polyreactive immunoglobulin M (IgM), exerting the highly anti-A/B/H-aggressive isoagglutinin activities. These activities physiologically undergo the ABO(H) blood group phenotype formation, occurring on the surfaces of red blood cells (RBC), epithelial and endothelial cells and on plasma proteins by identical glycosylation, performed by the ABO(H)-allelic glycotransferases, phenotypically downregulating the anti-A/B/H-reactive IgM (isoagglutinin) activities in the non-O blood groups. ABO(H) phenotype diversity, this way glycosidically linked and molecularly connected to humoral immunity, becomes exposed to the evolution.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

The Sei Dareh Bridge is a cable-stayed bridge located in West Sumatra Province, Indonesia. The bridge, has a main span of 123 meters length and 9 meters wide, crosses the Batanghari River. Traffic load is transmitted through 4 prestressed cables to a 42.4 meter high pylon made of concrete. Bridge deck and traffic loads are directly supported by steel box girders as main beams that are reinforced laterally with cross beams IWF 800.300.16.24 and stringers IWF 350.350.12.19. This paper discusses static and dynamic testing on the bridge which aims to assess the feasibility before it is opened for public. Based on the test, it was concluded that the 73% static load could not be achieved because the deflection that occurred was beyond the allowable deflection. This is exacerbated by the sound of a loud clanging sound on the ST2-X1 prestressed cable when loading to 240 tons or 58% of the targeted load. In addition, this bridge is included in the "lazy bridge" category because it takes 24 hours to return to an undeformed condition after loading. As a recommendation for this bridge, it is necessary to carry out a structural health monitoring system (SHMS) regularly on the vehicle floor and cables.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

Since the 21st century, China's urbanization process has been rapid development, the concept and function of urban public space in the city has been gradually paid attention to. In order to guarantee life and water, most urban construction relies on rivers, and Bridges are the most important way to communicate between urban areas. The main functional part of the bridge is the span structure, that is, the bearing structure of the bridge, and the lower part of the "gray" space formed by the bridge structure. Considering the social level, with the economic growth and urbanization development, people have brought a better living environment and quality of life, and also improved the requirements for urban public environment. In the increasingly tense urban space, how to use and transform the space under the bridge is a problem that needs to be considered and solved. In view of this problem, in this study, we try to solve the micro-transformation of space under Bridges in cities through public art from the perspective of "regional culture" and "art for all". This paper analyzes the micro-transformation of space art under Bridges in two large cities of Shanghai and Foshan, namely, the space under Bridges under Songhong Road in Shanghai, the space under Bridges under Central Of Suzhou River and the space under Bridges under Pingsheng Bridge in Foshan. This paper discusses the cultural intervention of "regional culture" in the micro-transformation of the space under the bridge, and the influence and effect of "art for all" on the public art space under the bridge after the transformation to the community and the public.

Near-fault ground motions can cause severe damage to civil structures, including bridges. Safety assessment of these structures for near fault ground motion is usually performed through Non-Linear Dynamic Analyses, while faster methods are often used. IMPAb (Incremental Modal Pushover Analysis for Bridges) permits to investigate the seismic response of a bridge by considering the effects of higher modes, which are often relevant for bridges. In this work, IMPAb is applied to a bridge case study considering near-fault pulse-like ground motion records. The records were analyzed and selected from the European Strong Motion Database and the pulse parameters were evaluated. In the paper results from standard pushover procedures and IMPAb are compared with nonlinear Response-History Analysis (NRHA), considering also the vertical component of the motion, as benchmark solutions and incremental dynamic analysis (IDA). Results from the case study demonstrate that the vertical seismic action has a minor influence on the structural response of the bridge. Therefore IMPAb, which can be applied considering vertical motion, remains very effective conserving the original formulation of the procedure, and can be considered a well performing procedure also for near-fault events.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

The average age of in-service bridges has increased in recent years in the United States. To address this issue, structural health monitoring and damage identification approaches can be employed to prioritize maintenance/replacement of aging bridges. Among the damage identification and operational health monitoring approaches, finite element (FE) model updating methods can offer a solution to evaluate the mechanics-based characteristics of bridges. However, in a real-world setting, unidentifiability and mutual dependency between model parameters, modeling errors, especially due to boundary conditions, as well as ill-conditioning of updating algorithms can pose challenges to the application of FE model updating methods. To address these challenges, this study presents a two-step FE model updating approach. In the first step, modal-based model updating is used to estimate linear model parameters mainly related to the stiffness of boundary conditions and material properties. In the second step, in order to refine parameter estimation accounting for nonlinear response behavior of the bridge, a time-domain model updating is carried out. In this step, boundary conditions are fixed at their final estimates using modal-based model updating. To prevent the convergence of updating algorithm to local solutions, the initial estimates for nonlinear material properties are selected based on their corresponding final estimates in the modal-based model updating. To validate the applicability of the two-step FE model updating approach, a series of forced-vibration experiments are designed and carried out on a pair of decommissioned and deteriorated prestressed bridge I-girders. After carrying out the two-step FE model updating, the final estimates of concrete compressive strength are shown to provide reasonable assessment of the damage extent in the girders.

In the modern construction industry, lightweight aggregate concrete (LWAC) is often used in the production of load-bearing structural members. LWAC can be up to 40% lighter by volume in comparison to normal strength concrete. On the other hand, the lack of adequate numerical models often limits the practical application of innovative building materials, such as lightweight concrete, in real projects. This trend is due to the uncertainties in design standard methods and calculation errors, the level of which is generally unacceptable to civil engineers in terms of safety and reliability. In the present paper, a comparative numerical deformation analysis of a full-scale bridge deck slab and girder has been carried out. Using the physical model proposed by the authors and the finite element software ATENA, the deformations of full–scale lightweight and traditional reinforced concrete elements under short-term effects of permanent and variable loads was compared. Depending on the safety and serviceability limit requirements, it was found that the amount of longitudinal reinforcement in lightweight reinforced concrete elements can be reduced compared to normal reinforced concrete elements with the same parameters. The results of the numerical analysis show that the deformation analysis model proposed by the authors can be a reliable tool for the design of lightweight concrete flexural members by selecting the optimum geometrical and reinforcement parameters limited by the stiffness condition.

It is not easy to dynamically analyze thermal bridges that require multidimensional analysis in building energy simulations, which are mostly one-dimensional platforms. To solve this problem, many studies have been conducted and, recently, a study was conducted to model the thermal bridge based on the data by approaching this in a similar way to steady-state analysis, showing high accuracy. This was an early-stage study, which is only applicable when the indoor temperature is constant. By extending this study, a thermal bridge model that can be applied even when the indoor temperature changes over time is proposed and validated. Since the governing equation, the heat diffusion equation, is linear, the key idea is to create and apply two thermal bridge transfer function models by expressing the heat flow entering the room as a linear combination of the transfer function for indoor temperature and the transfer function for outdoor temperature. For the proposed thermal bridge model, the NRMSE of the model itself showed a high accuracy of 99.9%, and in the verification through annual simulation using the model, the NRMSE showed an accuracy of 88.8%.

While the angiotensin converting enzyme 2 (ACE2) protein is defined as the primary severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) receptor, the viral serine molecule might be mobilized by the host's transmembrane protease serine subtype 2 (TMPRSS2) enzyme from the viral spike (S) protein and hijack the host’s N-acetyl-D-galactosamine (GalNAc) metabolism. The resulting hybrid, serologically A-like/Tn (T-nouvelle) structure potentially acts as a host–pathogen functional molecular bridge. In humans, this intermediate structure will hypothetically be replaced by ABO(H) blood group-specific, mucin-type structures, in the case of infection hybrid epitopes, implicating the phenotypically glycosidic accommodation of plasma proteins. The virus may, by mimicking the synthetic pathways of the ABO(H) blood groups, bind to the cell surfaces of the blood group O(H) by formation of a hybrid H-type antigen as the potential precursor of hybrid non-O blood groups, which does not affect the highly anti-glycan aggressive anti-A and anti-B isoagglutinin activities, exerted by the germline-encoded nonimmune immunoglobulin M (IgM). In the non-O blood groups, which have developed from the H-type antigen, these IgM activities are downregulated by phenotypic glycosylation, while adaptive immunoglobulins might arise in response to the hybrid A and B blood group structures, bonds between autologous carbohydrates and foreign peptides, suggesting the exertion of autoreactivity. The non-O blood groups thus become a preferred target for the virus, whereas blood group O(H) individuals, lacking the A/B phenotype-determining enzymes and binding the virus alone by hybrid H-type antigen formation, have the least molecular contact with the virus and maintain the critical anti-A and anti-B isoagglutinin activities, exerted by the ancestral IgM, which is considered the humoral spearhead of innate immunity.

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

Blackcurrant leaf chlorosis associated virus (BCLCaV) was detected recently by next-generation sequencing (NGS) and proposed as a new and distinct species in the genus Idaeovirus. Genomic components of BCLCaV that were detected and confirmed include: 1) RNA-1 that is monocistronic and encodes the replicase complex; 2) a bicistronic RNA-2 that encodes a movement protein (MP) and the coat protein (CP) of the virus, with open reading frames (ORF) that overlap by a single adenine (A) nucleotide (nt) representing the third position of an opal stop codon of the MP ORF2a and the first position of the start codon of the CP ORF2b; 3) a subgenomic form of RNA-2 (RNA-3) that contains ORF2b; and 4) a concatenated form of RNA-2 that consists of a complementary and inverted RNA-3 conjoined to the full-length RNA-2. Analysis of NGS-derived paired-end reads revealed the existence of bridge reads encompassing the 3’-terminus and 5’-terminus of RNA-2 or RNA-3 of BCLCaV. The full RNA-2 or RNA-3 could be amplified using outward facing or abutting primers; also RNA-2/RNA-3 could be detected even after three consecutive RNase R enzyme treatments with denaturation at 95 ^oC preceding each digestion. Evidence was obtained indicating that there are circular forms of BCLCaV RNA-2 and RNA-3.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.