We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

Human often cross their legs unconsciously while sitting, which can lead to issues like shifting the center of gravity, lower back pain, decreased blood flow and pelvic distortion. Detecting unconscious leg-crossing is important for maintaining correct posture. In this study, we explored the detection of leg-crossing postures using machine learning on data from body pressure distribution sensors. Collected 180 seconds of pressure data from 4 male subjects (25.8 ± 6.29 y.o.) in three conditions: no leg crossing, right leg crossed, and left leg crossed. Seven classifiers, including SVM and RF, were evaluated using Accuracy, Recall, Precision, and Specificity. As a result, SVM was difficult to classify.

Heart rate and blood pressure, along with body temperature and respiratory rate, are two of the four parameters used to assess the state of bodily functions, as both measures are indicators of heart activity. Therefore, these measurements become a basic procedure in patient diagnosis, necessitating techniques that can obtain them accurately and reliably, while being as non-intrusive as possible for the patient. Using video data, these two vital signs can be determined at any time and place. To achieve this, artificial intelligence techniques such as machine learning and deep learning 6 can be applied to overcome the main limitations of conventional remote photoplethysmography (rPPG). This document explains the technical and methodological aspects involved, including the acquisition and preprocessing of video data, the extraction of the rPPG signal, and its subsequent processing, as well as the artificial intelligence model for heart rate estimation and the mathematical modeling for blood pressure estimation. We compared the results for heart rate and blood pressure extracted from videos recorded by a basic smartphone front-camera to a blood pressure monitor and achieved results with reasonable accuracy and correlation. These results are part of the AIVA project, grant agreement 2021/C005/00145071. This project has been funded by Red.es through the Spanish 2021 call for grants aimed at research and development projects in artificial intelligence and other digital technologies.

Mediterranean diet, featuring sourdough bread, shows promise in managing metabolic syndrome. This study explored the effects of two sourdough breads with differing fermentation times but similar nutritional profiles on inflammation, satiety, and gut microbiota composition in adults with metabolic syndrome. The double-blind clinical trial randomized participants to consume over two-months Elias Boulanger® long fermentation (48h) sourdough bread (EBLong) or Elias Boulanger® short fermentation (2h) sourdough bread (EBShort). We assessed clinical parameters, inflammatory- and satiety-related biomarkers; and richness and abundance of gut microbiota at baseline and follow-up. 31 individuals (mean age: 67, 55.7% female) participated. EBShort was associated with reduced soluble intercellular adhesion molecule (sICAM) levels, and irrespective of the adjudicated intervention, all participants had a decrease in sICAM and diastolic pressure relative to baseline (p<0.017). At follow-up, plasminogen activator inhibitor-1 (PAI-1) levels were lower in EBShort (-744 pg/mL; 95%CI: -282 to -1210 pg/mL) compared to EBLong. High-quality sourdough bread may offer mild benefits in blood pressure and inflammation for those with metabolic syndrome, however, only EBLong was associated to reduced Enterobacteriaceae abundance. Further research is needed to understand potential benefits and mechanisms of sourdough bread in managing metabolic syndrome and improving cardiovascular health.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO2 has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O2-, ·OH), yet the low specific surface area of crystalline TiO2 depressed the catalytic performance. Herein, we prepared TiO2 aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO2 aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO2 aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO2 aerogel for the photocatalytic HCHO decomposition is 2 nm-10 nm. This study provides a theoretical idea for TiO2 aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO2 aerogels for green chemistry.

Porcine sapovirus (PoSaV) is a significant pathogen causing diarrhea with high morbidity and mortality rates. Given its zoonotic characteristics, this study conducts a comprehensive genetic evolutionary analysis of PoSaV. Results confirmed PoSaV as the primary RNA virus in piglet feces (27.54%). Phylogenetic analysis identifies the prevalent PoSaV strain SHCM/Mega2023 in the GIII genogroup, involving a recombinant event with MK962338 and KT922089. The time tree revealed that the GIII genogroup exhibits the widest divergence time span, indicating a high likelihood of viral recombination. Further selective pressure calculations demonstrate that PoSaV was under purifying selection (dN/dS < 1), with seven positively selected sites in VP1 protein which might be related to the antigencity. In conclusion, this study presents a novel genomic evolution of PoSaV, offering valuable insights into antigenicity and vaccine research.

Incretin effect helps in regulating glucose homeostasis and maintaining glycaemic control within the human body. This effect is achieved by the two naturally occurring incretin hormones: glucose-dependent insulinotropic polypeptide (GIP) and glucagon-like peptide-1 (GLP-1). Such hormones released by specialized entero-endocrine cells of the gastrointestinal tract cause insulin augmentation after food consumption. However, incretin effects are impaired in type 2 diabetic, primarily attributed to the deterioration of GLP-1 function along with decreased GLP-1 receptor expression. Targeting this hormone has, therefore, become an important therapeutic approach to treat this diabetic condition. Native GLP-1’s brief half-life and rapid proteolytic degradation have generated significant enthusiasm in uncovering the long-acting GLP-1 receptor (GLP-1R) agonists to manage type 2 diabetes. These synthetic peptides mimic the natural GLP-1 to activate GLP-1R and effectively exert various physiological benefits in terms of weight management, blood pressure, lipid profile, obesity and major adverse cardiovascular event. This review paper provides insights into the structure, function and expression of GLP-1 and its receptor. It also summarizes existing literature regarding different types of GLP-1 receptor agonists, their effects on blood pressure and how they exert their actions. While animal models have contributed significantly to this area of study, the scarcity of human studies is noted, indicating a need for more investigation in this domain. Expanding research in humans will help in comprehending the impact of GLP-1 receptor agonists on blood pressure regulation and their underlying mechanisms.

It is unknown whether postprandial plasma glucose measured from blood taken between 4 and 7.9 h (PPG4-7.9h) is associated with mortality from hypertension, diabetes, or cardiovascular disease (CVD). This study aimed to investigate these associations in 4,896 US adults who attended the third National Health and Nutrition Examination Survey. Cox proportional hazards models were used to estimate hazard ratios (HRs) and 95% confidence intervals (CIs) of PPG4-7.9h for mortality. This cohort was followed up for 106,300 person-years (mean follow-up, 21.7 years). A 1-natural-log-unit increase in PPG4-7.9h was associated with a higher risk of mortality from hypertension (HR, 3.50; 95% CI, 2.34-5.24), diabetes (HR, 11.7; 95% CI, 6.85-20.0), and CVD (HR, 2.76; 95% CI, 2.08-3.68) after adjustment for all the tested confounders except hemoglobin A1c (HbA1c). After further adjustment for HbA1c, PPG4-7.9h remained positively associated with mortality from hypertension (HR, 2.15; 95% CI, 1.13-4.08) and CVD (HR, 1.62; 95% CI, 1.05-2.51), but was no longer associated with diabetes mortality. Subgroup analyses showed that similar results were obtained in the sub-cohort of participants without a prior diagnosis of myocardial infarction or stroke. In conclusion, PPG4-7.9h predicts mortality from hypertension and CVD independent of HbA1c.

Background: Deoxycholic acid (DCA) is a secondary bile acid produced by gut bacteria. Its serum concentration increases in cardiovascular disease (CVD). We hypothesized that DCA may affect hemodynamic parameters in rats. Methods: The concentration of DCA in systemic blood was measured with liquid chromatography coupled with mass spectrometry. Arterial blood pressure (BP), heart rate (HR) and echocardiographic parameters were evaluated in anesthetized, male, 3-4-month-old Sprague-Dawley rats administered intravenously (IV) or intracerebroventricularly (ICV) with investigated compounds. Mesenteric artery (MA) reactivity was tested ex vivo. Results: The baseline plasma concentration of DCA was 0.24 ± 0.03 mg/l. The oral antibiotic treatment produced a large decrease in the concentration. Administered IV, the compound increased BP and HR in a dose-dependent manner. DCA also increased heart contractility and cardiac output. None of the tested compounds: prazosin (an alpha-blocker), propranolol (beta-adrenolytic), atropine (muscarinic receptor antagonist), glibenclamide (K-ATP inhibitor) or DY 268 (FXR antagonist), glycyrrhetinic acid (11HSD2 inhibitor) significantly diminished the DCA-induced pressor effect. ICV infusion did not exert significant HR or BP changes. DCA relaxed MAs. Systemic vascular resistance did not change significantly. Conclusions: DCA increases BP by increasing cardiac output. As a bioactive gut bacteria-derived metabolite, DCA may co the interaction between gut microbiota and the host’s circulatory system.

Objective To observe the effect of roxadustat on blood pressure and micro-inflammatory response in patients with hemodialysis anemia, and to provide a viable technique for the treatment of hemodialysis anemia patients. Methods A total of 100 hemodialysis anemia patients admitted to the Nephrology Department of our hospital from July 2020 to July 2021 were enrolled and randomly divided into an observation group (roxadustat) and a control group (human recombinant erythropoietin (rhEPO). The clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure were recorded and compared. Results There was no significant difference in baseline data and serum indicators (P>0.05). The study group demonstrated superior performance to the control group in terms of clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure (all P<0.05). Conclusion Compared with rhEPO treatment, roxadustat exhibits a promising outcome in treating anemia and has slight impact on blood pressure of patients.

(1) Background: Globally, neck pain is prevalent, affecting around thirty percent of the population annually. To better understand the influence of pain on the myofascial layers, the present study investigated these on the upper trapezius muscle in unilateral, more severe neck pain. (2) Methods: This study was a cross-sectional study. Forty patients (42.2 ± 14.7) with a confirmed diagnosis of unilateral neck pain were examined using durometry and indentometry. The study evaluated stiffness, elasticity, and pressure pain threshold of both sides of the neck (symptomatic side: SS; healthy side: HS). Furthermore, the range of motion of the cervical spine (lateral flexion, rotation) was quantified using a digital goniometer. (3) Results: A significant lateral discrepancy was observed in stiffness between groups (durometry: SS – 33.76 ± 7.78, HS – 29.75 ± 7.45, p&lt;0.001; indentometry: SS – 59.73 ± 33.93, HS – 4.18 ± 12.69, p=0.024). In contrast, no differences were found between the comparison sides of the upper trapezius for the parameter’s elasticity (SS – 0.101 ± 1.09, HS – -0.006 ± 0.29, p=0.416), cervical spine mobility (lateral flexion: SS – 37.08 ± 8.15, HS – 37.73 ± 7.61, p=0.559; rotation: SS – 73.55 ± 12.37, HS – 72.85 ± 11.10, p=0.660) and algometry (SS – 36.41 ± 17.53, HS – 37.22 ± 17.00, p=0.657). (4) Conclusion: Overall, it can be concluded that more severe neck pain unilaterally shows differences in stiffness on the same side. Future research is needed to investigate the links.

The accumulation of microplastics in the world oceans is one of the main global problems of the modern world. The Black Sea is the main source of seafood for people from several countries, including Bulgaria. The pollution of the Black sea is a result of various factors, especially anthropogenic. The present study demonstrated detailed MPs contamination of five fish species important for the commercial fishing (Garfish, Мullet, Knout goby, Pontic shad and Mediterranean horse mackerel) collected from the Sozopol area on the Bulgarian Black Sea coast. Within each microplastic morphological group, three size classes were recognized: 100-200 µm, 25-100 µm, and ≤ 25 µm. Microplastics were found in the soft tissues of all studied specimens but in a different ratio of pellets, fibers and fragments. Generally, the pellets were the most often registered particles, followed by irregularly-shaped fragments, whereas fibers were less numerous. The dominant part of the isolated plastics are made of polyethylene (PE), and polyethylene terephthalate (PET). Our results pointed out serious pollution with plastic particles in the Bulgarian Black Sea aquatory, which in the future may seriously affect the health of the fish population and also human health.

Cadmium (Cd) is a pervasive, toxic environmental pollutant that preferentially accumulates in tubular epithelium of the kidney. Current evidence suggests that the cumulative burden of Cd here leads to progress loss of the glomerular filtration rate (GFR). In this study, we have quantified changes in estimated GFR (eGFR) and albumin excretion (Ealb) in according to levels of blood Cd ([Cd]b) and excretion of Cd (ECd) after adjustment for confounders. ECd and Ealb were normalized to creatinine clearance (Ccr) as ECd/Ccr and Ealb/Ccr. Among 482 residents of Cd-polluted and non-polluted regions of Thailand, 8.1% had low eGFR and 16.9% had albuminuria, (Ealb/Ccr)×100 ≥ 20 mg/L filtrate. In the low Cd burden group, (ECd/Ccr) ×100 &lt; 1.44 µg/L filtrate, eGFR did not correlate with ECd/Ccr (β = 0.007), while an inverse association with ECd/Ccr was found in the medium (β =−0.230) and high-burden groups (β =−0.349). Prevalence odds ratios (POR) for low eGFR were increased in the medium (POR 8.26) and high Cd burden groups (POR 3.64). Also, eGFR explained a significant proportion of Ealb/Ccr variation among those with middle (η2 0.093) and high [Cd]b tertiles (η2 0.132), but did not with low tertile (η2 0.001). With adjustment of eGFR, age and BMI, POR values for albuminuria were increased in the middle (POR 2.36) and high [Cd]b tertiles (POR 2.74) and those with diabetes (POR 6.02) and hypertension (2.05). These data argue that ECd/Ccr of 1.44 µg/L filtrate (0.01−0.02 µg/g creatinine) could determine a Cd threshold level from which protective exposure guidelines should be formulated.

Due to wood’s susceptibility to fire, it is crucial to treat wood-based materials with flame retardants, especially in construction applications. This study investigated the effectiveness of various grooving types, including transverse, longitudinal, both transverse and longitudinal, and surface grooving, in enhancing larch's vacuum pressure impregnation process. The results revealed that transverse grooving provided a slightly greater impregnation advantage than longitudinal grooving. Moreover, exceptional impregnation performance was observed in larch samples subjected to both longitudinal and transverse grooving and surface grooving, exhibiting a remarkable improvement of 214,7 % compared to untreated larch.

In this study, we had investigated the use of high-pressure homogenization (HPH) as a novel pretreatment method for the extraction of sodium alginate (SA) from Laminaria japonica. Our results demonstrated that under optimal condition of 100 MPa HPH pressure, 4 cycles, pH 6.0, and 0.5% ethylene diaminetetra acetic acid tetrasodium salt (EDTA) concentration (w/v) for 3.0 hours, the extraction yield of HPH reached 34%, which was higher than that achieved by previous methods such as complex enzyme hydrolysis (CE), ultrasonic-assisted extraction (UAE), and complex enzyme-ultrasonic combined method (CE-UC). To further characterize the extracted SA, we conducted a comprehensive analysis using SEM, FTIR, MRS, NMR, XRD, TGA, and T-AOC assay. Our findings revealed the following: 1) HPH treatment significantly disrupted the structure of L. japonica cells and reduced their crystallinity to 76.27%, the lowest among all pretreatment samples; 2) the extracted SA had a greater tendency to form elastic gels; and 3) the antioxidant activity of HPH-extracted SA reached 0.02942 mgVceq∙mg-1, which was the highest among all tested methods. Based on these results, we concluded that HPH extraction not only increased the yield of SA but also enhanced its antioxidant activity.

With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Co-doped SnO2 nanocrystals with tetragonal rutile-type (space group P42/mnm) structure have been investigated using in-situ high-pressure synchrotron angle dis-persive X-ray diffraction till 20.9 GPa at ambient temperature. The analysis of ex-perimental results based on Rietveld refinements suggest that rutile-type SnO2 un-dergoes a structural phase transition at 14.2 GPa to an orthorhombic CaCl2-type phase (space group Pnnm) with no coexistence during the phase transition. No further phase transition is observed till 20.9 GPa. The low-pressure and high-pressure phases are related via a group/subgroup relationship. However, as a discontinuous change in the unit-cell volume is detected at the phase transition, thus, the phase transition can be classified as first-order type. On decompression the transition is found to be re-versible. The results are compared with previous high-pressure studies on SnO2.

Although, central venous pressure (CVP) is among the most frequent estimated hemodynamic parameters in the critically ill setting, extremely little is known on how intensive care unit (ICU) nurses use this index in their decision-making process. The purpose of the study was to develop a new questionnaire for accessing how ICU nurses use CVP measurements to address patients’ he-modynamics investigating its validity and reliability. A cross-sectional study was conducted among 120 ICU nurses from four ICUs of Greece. Based on a comprehensive literature review and the evaluation of a five-experts panel a new questionnaire, named “CVP-Score”, was created having 8 items. The construct validity and the reliability of the questionnaire were examined. The half of the study participants’ (51.7%) was working at a specialized ICU, and they had a mean [±Standard Deviation (SD)] ICU experience of 13(±7.1) years. The estimated construct validity of the new-developed tool was acceptable, while the internal consistency reliability as measured by Cronbach alpha was excellent (0.901). CVP Score had acceptable test-retest reliability (r=0.996, p<0.001) and split-half reliability (0.855). CVP Score is a valid and reliable instrument for measuring how critical care nurses use CVP measurements in their decision-making process.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

INTRODUCTION: Cardiovascular prevention is less effective than expected due to the concern about polymedication of professionals and the lack of adherence of patients. Polypills are presented as a possible solution, increasing therapeutic adherence in the medium or long term and improving therapeutic results compared to the administration of drugs separately: they increase effectiveness and Adherence of patients to primary and secondary cardiovascular prevention programs, without increasing the cost of the intervention. OBJECTIVES: Study #Trigeria: to specify the combined prevalence of Atrial Fibrillation, Dyslipidemia and Hypertension and analyze the pharmacological prescription for these pathologies and the possible indications and advantages that would have the prescription of a polypill for these risk factors.METHODS: Observational analytical study on the pathological history in elderly institutionalized in nursing homes and analysis of prescribed oral medication.RESULTS: 169 people analyzed (79.3% women) from 4 nursing homes; 8.9% had a history of Atrial Fibrillation, Dyslipidemia and Arterial Hypertension; these had a higher prevalence of heart disease (42.9%) and Cerebral Vascular Accident (35.7%). Polymedication was present in 88.5%, with an average of 6.94 oral drugs prescribed; among those with the three pathological antecedents, the average number of oral medications was 8.60. Only 26.7% of those with all three factors were prescribed drugs to control them.DISCUSSION: There are high rates of polymedication in the sample and low rates of prescription of antiplatelet agents in people with Atrial Fibrillation (26.5%); the low prescription of statins and antihypertensives of the ACE inhibitor or ARB-II groups may be due to good control with non-pharmacological measures or by the use of other groups of drugs . A polypill holding the drugs that control the three factors studied could increase the prescription rate while simplifying the administration schedule and reducing polymedication by 23.25% improving prescription, increasing adherence and control of risk factors without increasing pharmaceutical expenditure.CONCLUSIONS: There is a low rate of prescription of antiplatelet agents among people with atrial fibrillation. Combination methods (polypills) can increase the suitability of prescriptions in people with polypathology, improving prescribing, simplifying administration and increasing adherence to pharmacological treatments.

Diabetes mellitus leads to cardiovascular complications including impaired cardiac β-adrenoceptor (β-AR) function. Sodium-glucose cotransporter-2 (SGLT2) inhibitors, such as empagliflozin (EMPA) improve outcomes in heart failure patients and animal models thereof. Therefore, we have investigated the effects of EMPA on in vivo cardiac function (pressure-volume loop analysis) and β-AR-mediated contractile responses (papillary strips) in streptozotocin (STZ; 40 mg/kg, i.p.)-induced diabes in male Sprague Dawley rats (control, EMPA-treated control, diabetic, EMPA-treated diabetic) in a design reflecting late-onset treatment. 13-16 weeks after STZ injection treatment with a low dose of EMPA (10 mg/kg/day, daily oral gavage) or vehicle was administered for another 8 weeks. EMPA did not change cardiac function in control rats. Diabetic rats had a reduced heart rate, cardiac output, stroke work, rate of contration and rate of relaxation and increased isovolumic relaxation, whereas in vitro responses were not markedly attenuated. Treatment with EMPA showed a trend for improvement of some but not all parameters. Our results indicate that low dose EMPA treatment had limited effects on cardiac impairment despite reducing blood glucose when initiated after diabetes is manifest. Future studies with a higher dose and greater sample sizes could help to clarify the possible benefits of EMPA on the diabetic heart.

We validated a new noninvasive tool (B4C) to assess intracranial pressure waveform (ICPW) morphology in a set of neurocritical patients, correlating the data with ICPW obtained from invasive catheter monitoring. Materials and Methods: Patients undergoing invasive intracranial pressure (ICP) monitoring were consecutively evaluated using the B4C sensor. Ultrasound-guided manual internal jugular vein (IJV) compression was performed to elevate ICP from the baseline. ICP values, amplitudes, and time intervals (P2/P1 ratio and time-to-peak [TTP]) between the ICP and B4C waveform peaks were analyzed. Results: Among 41 patients, the main causes for ICP monitoring included traumatic brain injury, subarachnoid hemorrhage, and stroke. Bland-Altman’s plot indicated agreement between the ICPW parameters obtained using both techniques. The strongest Pearson’s correlation for P2/P1 and TTP was observed among patients with no cranial damage (r = 0.72 and 0.85, respectively) in detriment of those who have undergone craniotomies or craniectomies. P2/P1 values of 1 were equivalent between the two techniques (area under the receiver operator curve [AUROC], 0.9) whereas B4C cut-off 1.2 was predictive of intracranial hypertension (AUROC 0.9, p < 000.1 for ICP > 20 mmHg). Conclusion: B4C provided biometric amplitude ratios correlated with ICPW variation morphology and is useful for noninvasive critical care monitoring.

Purpose: To compare ab interno trabeculectomy by trabecular meshwork excision to plasma-mediated ablation in primary open-angle glaucoma. Methods: Retrospectively collected data of TrabEx+ (TEx, n=56) and Trabectome (T, n=99) were compared by coarsened exact matching to reduce confounding and matched based on baseline IOP and age. Primary outcomes were IOP and number of glaucoma medications. Complications and need for additional glaucoma surgery were assessed. Patients were followed for up to one year. Results: 53 TEx could be matched to T. Baseline IOP was 16.5±4.6 mmHg in both; age was 73.7±8.8 and 71.5±9.9 years in TEx and T, respectively. TEx were taking more medications than T (p<0.001). IOP was reduced to 14.8±4.3 in TEx and to 13.4±3.4 in T at 6 months, and to 14.9±6.0 (p=0.13) in TEx and to 14.1±3.8 mmHg (all p<0.05) in T at 12 months. Medications were reduced at both 6 and 12 months (p< 0.05). No differences were seen between TEx and T at 6 and 12 months. In TEx, only one serious complication occurred, and two patients required further glaucoma surgery. Conclusion: Although both groups had a baseline IOP considered low for ab-interno trabeculectomy, IOP and medications were reduced further at 6 and 12 months. IOP reduction did not reach significance in TEx at 12 months. The inter-group comparison did not reveal any significant differences. Both had a low complication rate.

Purpose: To determine whether 24-hour IOP monitoring can be a predictor for glaucoma progression and to analyze the inter-eye relationship of IOP, perfusion and progression parameters. Methods: We extracted data from manually drawn IOP curves with HIOP-Reader, a software suite we developed. The relationship between measured IOPs and mean ocular perfusion pressures (MOPP) to retinal nerve fiber layer (RNFL) thickness was analyzed. We determined the ROC curves for peak IOP (Tmax), average IOP (Tavg), IOP variation (IOPvar) and historical IOP cut-off levels to detect glaucoma progression (rate of RNFL loss). Bivariate analysis was conducted to check for various inter-eye relationships. Results: 217 eyes were included. The average IOP was 14.8±3.5 mmHg, with a 24-hour variation of 5.2±2.9 mmHg. 52% of eyes with RNFL data showed disease progression. There was no significant difference in Tmax, Tavg and IOPvar between progressors and non-progressors (all p>0.05). Except for Tavg and the temporal RNFL, there was no correlation between disease progression in any quadrant, Tmax, Tavg and IOPvar. 24-hour and outpatient IOP variables had poor sensitivities and specificities in detecting disease progression. The correlation of inter-eye parameters was moderate; correlation with disease progression was weak. Conclusion: In line with our previous study, IOP data obtained during a single visit (outpatient or inpatient monitoring) make for a poor diagnostic tool, no matter the method deployed. Glaucoma progression and perfusion pressure in left and right eyes correlated weakly to moderately with each other.

Background: Morphological alterations in intracranial pressure pulse waveform (ICPPW) secondary to intracranial hypertension (ICP >20 mmHg) and reduction in intracranial compliance (ICC) are well known indicators of neurological severity. To date, no studies have documented the ICPPW modifications after intracranial hypertension resolution with decompressive craniectomy (DC). The present study aimed to assess the morphological alterations in ICPPW among neurocritical care patients with and without DC, by comparing the variations of ICPPW features according to elevations in mean ICP values. Methods: Patients requiring ICP monitoring because of severe traumatic or spontaneous conditions were included. Mean ICP values were compared with ICPPW features (P2/P1 ratio, TTP and pulse amplitude). Elevation in ICP was produced by means of ultrasound-guided manual internal jugular veins compression. Results were distributed for three groups: intact skull (exclusive burr hole for ICP monitoring), craniotomy/large fractures (group 2) or DC (group 3). Results: 57 patients were analyzed. 21 (36%) presented no skull defects, whereas 15 (26%) had DC. ICP was not significantly different between groups: ±13.59 for intact and ±17.66 mmHg for DC, with ICP induced elevation also similar between groups (p= 0.56). Significant elevation was observed for P2/P1 ratio for groups 1 and 2, whereas reduction was observed in group 3 (elevation of ±0.09 for groups 1 and 2, whereas reduction of 0.03 for group 3, p=0.01). Conclusion: In the present study, intracranial pressure pulse waveform analysis indicated that intracranial compliance was significantly more impaired among decompressive craniectomy patients, although ICPPW indicated DC to be protective for further influences of ICP elevations over the brain. Analysis of ICPPW seems to be an alternative to real time ICC assessment.

We propose the physical proof-of-concept of a new simple miniature pressure sensor based on the whispering gallery modes (WGMs) optically excited in a dielectric microsphere placed near a flexible reflective membrane, which acts as an ambient pressure sensing element. WGMs excitation is carried out by free-space coupling of optical radiation to a microsphere. The distinctive feature of proposed sensor design is double excitation of optical eigenmodes by forward and backward propagating radiation reflected from a membrane that causes WGMs interference in particle volume. The optical intensity of resulting resonant field established in the microsphere carries information about the exact position of the pressure-loaded reflecting membrane. The sensitivity of the proposed sensor strongly depends on the quality factor of the excited resonant mode, as well as geometrical and mechanical parameters of the flexible membrane. We propose to register not the displacement of the position of the WGM resonance, but the change in its amplitude under the influence of the change in the distance between the sphere and the mirror under the influence of pressure. Important advantages of the proposed sensor are miniature design (linear sensor dimensions depends only on the membrane diameter) and the absence of a mechanical contact of pressure-sensitive element with WGM resonator.

Mediterranean Ridge accretionary complex (MAC) is one of the most critical subduction zones in the world. It is known that the region exhibits a continuous mass change (horizontal/vertical movements). This process is associated with the devastating and tragic earthquakes shaking the MAC for centuries. Here, we investigate the ocean bottom pressure (OBP) anomalies in the MAC derived from the Gravity Recovery and Climate Experiment (GRACE) and GRACE Follow On (GRACE-FO) satellite missions. The OBP time series for the MAC comprises a decreasing trend in addition to 1-, 1.53-, 2.36-, 3.67-, and 9.17-year periodic components partially explained by the atmosphere, oceans, and hydrosphere (AOH) processes, and Earth's pole movement. We noticed that the OBP anomalies appear to link to a rising trend and periods in earthquakes' power time series. This finding sheds new light on the mechanisms controlling the most destructive natural hazard.

Pistachio and cashew contain allergenic proteins, which causes them to be removed from the diet of allergic people. Former evidences have demonstrated that food processing (thermal and non-thermal) can produce structural and/or conformational changes in proteins by altering their allergenic capacity. In this study, the influence of Instant Controlled Pressure Drop (DIC) on the pistachio and cashew allergenic capacity has been studied. Western blot was carried out using IgG anti-11S and anti-2S and IgE antibodies from sera of patients sensitized to pistachio and cashew. DIC processing causes changes in the electrophoretic pattern, reducing the number and intensity of protein bands, as the pressure and temperature treatment increment what results in a remarkable decrease of detection of potentially allergenic proteins. The harshest conditions of DIC (7bar, 120s) markedly reduce the immunodetection of allergenic proteins, not only by using IgG (anti 11S and anti 2S) but also when IgE sera from sensitized patients were used for Western blots. Such immunodetection is more affected in pistachio than in cashew nuts, but it not completely removed. Therefore, cashew proteins are possibly more resistant than pistachio proteins. According these findings, Instant Controlled Pressure Drop (DIC) can be considered a suitable technique in order to obtain hypoallergenic tree nuts flour to be used in food industry.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

Computational Fluid Dynamics (CFD) is utilized to study entropy generation for the rarefied steady state laminar 2-D flow of air-Al2O3 nanofluid in square cavity equipped with two solid fins at the hot wall. Such flows are of great importance in industrial applications, such cooling of the electronic equipment’s and nuclear reactors. In the current study, effects of Knudsen number (Kn), Rayleigh number (Ra) and the nano solid particles volume fraction (ϕ) on the entropy generation are investigated. The values of parameters considered in this work are as follows: 0≤Kn≤0.1, 〖10〗^3≤Ra≤〖10〗^6,0≤ϕ≤0.2. Length of the fins (LF) is considered to be fixed and equals to 0.5 m, whereas the location of the fins with respect to the lower wall (HF) is set to 0.25 and 0.75 m. Simulations demonstrate that there is an inverse direct effect of Kn on the entropy generation. Moreover, it is found that when Ra is less than 104, the entropy generation, due to the flow, increases as ϕ increases. In addition, the entropy generation due to the flow will decrease at Ra greater than 104 as ϕ increases. Moreover, the entropy generation due to heat will increase as both the ϕ and Ra increase. In addition, a correlation model of the total entropy generation as a function of all of the investigated parameters in this study is proposed. Finally, an optimization technique is adapted to find out the conditions at which the total entropy generation is minimized

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

This is a review of efforts to discover action principles for Hydrodynamics and Thermodynamics. The work began with a determined attempt to create sources for Einstein's equations that describe continuous matter - as opposed to point particles. This requires a relativistic action principle. This report is mainly about (non relativistic) Adiabatic Thermodynamics, non equilibrium thermodynamics based on the method of Gibbs. The main relations of classical thermodynamics can be derived from an action principle, in the classical global form and in the local form advocated by Callen. The entropy is defined as the negative derivative of the free energy (free energy density) with respect to the volume (density). This is integrated with an action principle for hydrodynamics that was known to Lagrange in 1760. It is strongly limited to irrotational velocity fields, nevertheless it provides the needed Lagrangian for a large part of thermodynamics. This is the subject of the first 3 sections. It includes a brief review of a new theory of mixtures. The most difficult part of the program has been the discovery of Conservative Hydrodynamics with the required four independent degrees of freedom, with general flows. We give an account of the genesis and the structure of this theory, then a tour of recent applications.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

Purpose: To investigate whether microsurgical excision of trabecular meshwork (TM) in an ex vivo pigmentary glaucoma model can normalize the hypertensive phenotype. Methods: Eight eyes of a porcine pigmentary glaucoma model underwent 90° of microsurgical TM excision with an aspirating dual-blade (Goniotome (G)). 24 hours later, an additional 90° of TM were removed. Anterior segments with sham surgeries served as the control (C). Outflow facility and intraocular pressure (IOP) were analyzed. Histology with hematoxylin and eosin (H&E) was obtained. Results: After the first 90° TM excision, IOP was significantly lower in G (10.23±2.39 mmHg, n=7) than C (20.04±1.97mmHg, n=8, P<0.01). Outflow facility in G (0.38±0.07 µl/min/mmHg) was higher than C (0.16±0.02 µl/min/mmHg, P<0.01). After the second 90° TM excision, IOP in G (6.46±0.81 mmHg, n=7) was significantly lower than C (20.25±1.66 mmHg, n=8, P<0.001), while the outflow facility in G (0.50±0.05 µl/min/mmHg, n=7) was higher than C (0.16±0.01 µl/min/mmHg, n=8, P<0.001). Compared to the first excision, excision of an additional 90° did not change of IOP (P=0.20) or outflow facility (P=0.17) further. Conclusion: Excision of 90° of TM in a pigmentary glaucoma model using an aspirating dual-blade decreased IOP and increased outflow facility. Translational Relevance: Microsurgical TM excision over 90° can effectively restore outflow in pigmentary glaucoma.

A numerical study of the flow over a NACA aerofoil is presented in this paper. The numerical simulations are achieved with the computer code CFX and the computational domain is created by the computer tool ANSYS ICEM CFD. The CFX code is based on the finite volume method to solve the equations of mass, momentum and energy. The purpose of this paper is to determine the pressure distribution, flow patterns and the forces acting on the airfoil. Effects of the attack angle and Reynolds number on the velocity and pressure distribution, on the lift and drag coefficients are also explored.

Blood gas analysis is a diagnostic tool to evaluate the partial pressures of gas in blood and acid-base content. The use of blood gas analysis enables to clear understanding the respiratory, circulatory, and metabolic disorders. The arterial blood gas (ABG) explicitly analyzes blood taken from an artery, assessing the patient's partial pressure of oxygen (PaO2), carbon dioxide (PaCO2) pH (acid/base). PaO2 indicates the oxygenation status, and PaCO2 indicates the ventilation status (chronic or acute respiratory failure). PaCO2 is affected by hyperventilation characterized by rapid or deep breathing, and hypoventilation characterized by slow or shallow breathing. The acid-base balance tested by the ABG procedure measures the pH and PaCO2 directly while the use of the Hasselbach equation gives the serum bicarbonate (HCO3) and base deficit or excess. The measured HCO3is based on strong alkali that frees all CO2 in serum, including dissolved CO2, carbamino compounds, and carbonic acid the calculation uses a standard chemistry analysis giving the amount of "total CO2", the difference will amount to around 1.2 mmol/L. Though ABG is frequently ordered in emergency medicine contests for acute conditions it may also be needed in other clinical settings. The ABG analysis shows to be an exceptional diagnostic tool including the group of those diseases known as acid-base diseases (ABDs) which include a great variety of conditions as such severe sepsis, septic shock, hypovolemic shock, diabetic ketoacidosis, renal tubular acidosis, chronic respiratory failure, chronic heart failure, and diverse metabolic diseases.

The aim of the studies was to test the hydraulic pressure losses along the length, local pressure losses, absolute and relative roughness values of the pipeline walls made of modern polymer material. The article presents the results of the experimental studies of hydraulic resistance of pipelines from modern polymer materials, the method of theoretical determination of resistance coefficients in the VALTEC ISO 21003 metal polymer pipeline, the classification and method of determining the values of local hydraulic resistance coefficients of T-Junctions are given, the dependence for determining the Darcy λ hydraulic friction coefficient associated with the value of the equivalent hydraulic roughness coefficient of the inner surface of pipes and the Reynolds number. The experimental data of the hydraulic coefficient of friction Darcy λ was compared with the known theoretical relationships of A.D. Altschul, Colbrooke for smooth pipes, Colbrooke and White, an alternative to the Colbrooke-White, Offengenden equation for low-shear pipes and pipes from polymer materials with Reynolds numbers Re>10^4. Dependence of hydraulic coefficient of friction on relative equivalent roughness of pipeline walls and Reynolds number, specific energy loss per one linear meter on total flow rate in system of hydraulically short pipeline is obtained. The empirical dependence of values of coefficients of local resistance ζ=f(Q2/Q3) from a ratio of the divided expenses of Q2/Q3 of the equal-pass T-Junction α=90 the pipeline to a branch up, on pass in the direct T-Junction and division of streams at various internal pipeline diameters of VALTEC.

An analysis of the current state of development in the agro-industrial complex (AIC) has established that freeze-drying is the most effective method for processing raw materials entering the drying stage. However, this drying method is hindered by the lack of modern, high-performance, energy-efficient drying technologies and equipment. The production of freeze-dried agricultural products will stimulate the development of AIC sectors. The implementation scheme of an automatic control system for a vacuum freeze-drying unit is considered, representing a promising and environmentally friendly direction in the processing of agricultural products. The drying equipment includes the following components and systems: a drying chamber, a cooling system, a vacuum pump, a control system, and a heating system. The product is placed on shelves in the drying chamber and frozen to a temperature that ensures the removal of 75-80% of the moisture contained in the product. The vacuum pump creates a pressure of 10-30 Pa and evacuates the spent air from the sublimator. Water vapor condensation occurs in the desublimator, and at the final stage of the drying process, the heating elements are activated to remove the remaining moisture. To validate the reliability of controlling the operating modes of the sublimator, experimental studies were conducted on the temperature dependence of the product on the surface and in the center over time. The graphs show temperature changes on the surface and in the center of the product throughout the drying process. The research results indicate that at a pressure of 20±5 Pa, the desublimator temperature should be below -20°C. The surface temperature of the product during the sublimation stage should be within the range of -25±5°C. Drying is completed when the chamber temperature reaches no more than 40°C, and the surface temperature of the product is around 30°C.

This paper employs the Finite Element Method (FEM) to simulate and analyze the effects of corrosion defect parameters on the stress and failure pressure of pipelines. It investigates how the boundary conditions of the pipeline model influence stress and examines the sensitivity of failure pressure to corrosion defect parameters. A nonlinear regression equation has been developed from a dataset obtained through simulation experiments to predict the failure pressure of corroded pipelines. To validate the effects of corrosion defect parameters on failure pressure, a hydrostatic test platform for an API 5L X65 pipeline with corrosion defects was established to measure stress levels and failure pressures across varying corrosion defects. The study reveals that failure pressure is negatively correlated with corrosion length and depth, while positively correlated with corrosion width. Among these parameters, corrosion depth exerts a more significant influence on the pipeline's failure pressure than corrosion length and width. Within the range of corrosion defect parameters examined, the maximum deviation of the prediction equation's results from the simulation results is 8.71%, with an average deviation of 5.81%. The standard deviation of the fitted residuals is 0.01837. Additionally, the maximum deviation between the predicted results and experimental measurements is 8.39%, with an average deviation of 7.77%. The strong agreement between the predicted results from the equation and the actual measured data underscores the effectiveness of the nonlinear regression equation.

Hypertension is a major risk factor for cardiovascular and cerebrovascular diseases. Previous studies have indicated that the presence of heavy metals in the air may be a risk factor for hypertension. This study examined the combined effects of heavy metals on blood pressure considering, sex differences. A health impact survey was conducted with 561 residents near waste incineration facilities in Buki-myeon, Cheongju, Korea. Blood samples were analyzed for heavy metal concentrations, and the blood pressure was measured. Multiple linear and Bayesian kernel machine regressions (BKMR) were used to assess the association between heavy metal exposure and blood pressure. Men had higher blood mercury and lead concentrations, while women had higher cadmium levels. The multiple linear regression analysis revealed no significant associations between heavy metals and systolic blood pressure. However, cadmium was significantly associated with increased diastolic blood pressure in the total group and women, whereas lead was associated with the same in men. In the BKMR analysis, the joint effect of the three metals was significantly associated with diastolic blood pressure below the 45th percentile and above the 55th percentile only in men. These findings underscore the importance of considering sex differences in environmental health studies and public health strategies.

In order to study the corrosion resistance of 904L composite plate pressure vessel under high temperature and high pressure gas field environment, the pitting corrosion and stress corrosion cracking resistance of 904L composite plate body and weld material were compared with those of 2205 composite plate and 825 composite plate, which have been used in high temperature and high pressure gas field environment. The results showed that the pitting resistance of 904L composite plate was lower than that of 825 composite plate and higher than that of 2205 solid solution pure material plate and 2205 composite plate. The corrosion resistance of welds on 904L composite plate with different materials was very different. The corrosion rate of 904L composite plate body, welding seam and surfacing welding were all slight corrosion, and the sensitivity of chloride stress corrosion cracking was low in the simulation of the corrosion environment of high temperature and high pressure gas field. 904L composite plate met the requirements of corrosion resistance of pressure vessel material in high temperature and high pressure gas field environment.

This study simulated the effects of direct predatory pressure, indirect predatory pressure, and conspecific injury signals on the sea cucumber (Apostichopus japonicus) to determine changes in the activity of immune defense enzymes (lysozyme, acid phosphatase, alkaline phosphatase) and antioxidant stress enzymes (catalase, superoxide dismutase, malondialdehyde). Samples of sea cucumber juveniles were collected at 3 hours, 12 hours, 72 hours, and 96 hours post-predatory stress, and six enzymes related to immune defense and antioxidant stress were selected for activity assays, namely lysozyme (LZM), acid phosphatase (ACP), alkaline phosphatase (AKP), superoxide dismutase (SOD), catalase (CAT), and malondialdehyde (MDA). The results indicated that under direct predatory pressure, the activity of catalase in sea cucumbers was significantly higher than that of the control group at 3 hours (P < 0.05), while the activities of acid phosphatase, alkaline phosphatase, and catalase were significantly lower at 72 hours (P < 0.05). Under indirect predatory pressure, the activity of malondialdehyde in sea cucumbers was significantly higher than that of the control group at 12 hours (P < 0.05), the activity of alkaline phosphatase was significantly higher at 72 and 96 hours (P < 0.05), catalase was significantly lower at 72 hours, and the activity of superoxide dismutase was significantly higher at 72 hours (P < 0.05). Under the influence of conspecific injury signals, the activity of malondialdehyde in sea cucumbers was significantly higher than that of the control group at 12 hours (P < 0.05), and the activity of superoxide dismutase was significantly higher at 96 hours (P < 0.05). The sea cucumber enhanced its antioxidant capacity 3 hours after facing the predator, while its immune defense mechanism was suppressed at 72 hours. When facing indirect predatory pressure, the sea cucumber may have made immune and antioxidant preparations for the arrival of unknown risks. The experimental results show that predatory pressure has a significant impact on the immune and antioxidant functions of sea cucumbers, which may be related to the physiological state and environmental adaptability of the sea cucumber. This study provides a new perspective for understanding how sea cucumbers cope with predatory pressure in the natural environment and offers theoretical support for the cultivation management of sea cucumbers.

Duchenne muscular dystrophy (DMD) is the most prevalent progressive muscular dystrophy, and the guidelines recommend the regular assessment of respiratory muscle function. This study aimed to assess the relationship between maximum inspiratory pressure (MIP), maximum expiratory pressure (MEP) and sniff nasal inspiratory pressure (SNIP) measurements and upright-supine spirometry parameters in children with DMD, predictability of upright-supine spirometry in terms of diaphragm involvement, and impact of nutrition on muscle strength. This prospective cross-sectional study examined patients with DMD by comparing upright and supine FVC, MIP, MEP, and SNIP measurements. Forty-four patients were included in the study. The mean patient age was 10.8±2.9 years. Twenty-five patients were ambulatory. A significant decrease in FVC, FEV1, and FEF25-75 values was detected in the supine position in both ambulatory and nonambulatory patients (p&lt;0.05). All patients had low MIP, MEP, and SNIP measurements (less than 60 cm H2O). MIP, MEP, and SNIP values were significantly lower in patients with malnutrition than in those without (p&lt;0.05). To accurately assess respiratory muscle strength, supine FVC should be combined with upright FVC, MIP, MEP, and SNIP measurements. It is crucial to regularly screen patients for malnutrition, as this can significantly affect respiratory muscle function during pulmonology follow-up.

Mangrove ecosystems are one of the most productive on our planet but have declined globally by 30-50%. Many species rely on mangrove habitat and thus their conversion to aquaculture farms has led to a noticeable loss in commodities such as wild fish stocks. This study aimed to assess 1) the influence of the presence of aquaculture and 2) restoration projects on the ecosystems ability to provide resources. We collected data on mangrove vegetation (i.e., biomass, richness and abundance), soil nutrients (i.e. organic carbon, aluminium and nitrogen), crab abundance and fishing pressure in six sites. We set up 15 plots in each site and collected data between May and July 2023. Via generalised linear mixed models we found that the abundance and richness of crabs was significantly higher in aquaculture plots than in no aquaculture plots. Aquaculture plots had higher topsoil aluminium, topsoil and subsoil Nitrogen, and had lower topsoil Carbon than non-aquaculture sites. Restored sites had less Nitrogen in the topsoil than unmanaged sites. Biomass did not change between aquaculture, restored and unmanaged plots. We found a negative correlation between crab abundance and richness and mangrove DBH, suggesting that the species of crabs present preferred areas with propagules for feeding (e.g., Grapsidae crabs). The content of nitrogen in the subsoil was positively correlated with mangrove richness, diversity and height, suggesting the importance of nitrogen availability for mangrove growth. The content of aluminium in the subsoil was negatively correlated with the content of organic carbon both in topsoil and subsoil, suggesting the detrimental effect of aluminium on the carbon cycle. Fishing practices were observed in all sites during the data collection period. Even if most of the vegetation parameters were not significantly affected by presence of aquaculture or management for restoration, it is clear that important variables such as aluminium carbon, and nitrogen content in the soil and crab assemblages were highly variable.

The hyperactivation of the sympathetic nervous system (SNS) is linked to obesity, hypertension, and type 2 diabetes, with elevated norepinephrine (NE) levels being a key feature. Previous research has shown increased sodium-glucose cotransporter 1 (SGLT1) protein in kidneys of hypertensive rodents, prompting investigation into SGLT1 expression in other tissues such as skeletal muscle. This study aimed to assess: i) whether skeletal muscle cells and tissue express SGLT1 and SGLT2 protein; ii) if NE increases SGLT1 in skeletal muscle cells and iii) whether skeletal muscle of neurogenically hypertensive mice exhibits increased SGLT1 expression. We found that i) skeletal muscle cells and tissue are a novel source of SGLT2 protein and ii) NE significantly elevated SGLT1 in skeletal muscle cells. As SGLT2 inhibition (SGLT2i) with Empagliflozin increased SGLT1, in vivo studies with the dual SGLT1/2i, Sotagliflozin were warranted. Treatment of neurogenically hypertensive mice with Sotagliflozin significantly reduced blood pressure. Our findings suggest that SNS activity upregulates the therapeutic target, SGLT1 in skeletal muscle, potentially worsening cardiometabolic control. As clinical trial data suggests cardiorenal benefits with SGLT2i, future studies should aim to utilize sole SGLT1i which may offer a therapeutic strategy for conditions with heightened SNS activity, such as hypertension, diabetes and obesity.

This research assessed the level of peer influences among the students of Ebonyi State University, Abakaliki and the existing policy framework in the University to control its negative impact. Objectives: To assess the knowledge, attitude and practice of peer pressure influence control among the students of the institution. Methodology: We used a cross-sectional design, a structured questionnaire of a five-point Likert scale as a veritable instrument for collecting the data from 30 student respondents. The questionnaire was made up of four key sections comprising student’s demographic parameters, knowledge, attitude and practice of students on the subject matter. Data collected was analyzed in a table of descriptive statistics to determine the total, range, mean and median, which were used to ascertain students’ level of knowledge, attitude, practice and countermeasures to overcome negative peer influences emanating from their peers. Results: The mean value outcome of knowledge of students fall between 2.7 to 3.3, the mean value for attitude of student falls between 2.4 to 3.6, while the practice of students falls between mean value 2.7 and 3.2. Most of these outcomes represents poor or weak weight factor which requires several levels of interventions. Conclusion: This study highlights the overriding importance of peer pressure management among the students of Ebonyi State University, Abakaliki to create a safe academic environment and guarantee higher academic performances. This research recommended that the University management should commission research on peer pressure among students, the causes, manifestations and possible remedies to enable them to develop a comprehensive framework for the University.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

Chronic exposure to the nephrotoxic metal pollutant, cadmium (Cd), has been associated with hypertension, but the mechanism by which it raises blood pressure is not understood. We hypothesize that exposure to Cd reduces the glomerular filtration rate (GFR), which in turn, causes a rise in blood pressure. Data were collected from 447 Thai subjects with a mean age of 51.1 years, of which 48.8% had hypertension, 15.4% had diabetes and 6.9% had an estimated GFR (eGFR) below 60 mL/min/1.73 m2 (low eGFR). The mean blood and urinary Cd concentrations were 2.75 and 4.23 µg/L, respectively. The prevalence odds ratio (POR) for hypertension rose twofold in those with blood Cd levels of 0.61-1.69 µg/L or urinary Cd excretion levels ≥ 0.98 µg/g creatinine. In the hypertensive group, the eGFR was inversely associated with age (β =−0.517), the Cd excretion rate (β = −0.177), and diabetes (β = −0.175). Mean eGFR in the normotensive group was 7.5 mL/min/1.73 m2 higher than the hypertensive with a similar Cd body burden. Mean systolic blood pressure (SBP) in those with low or medium eGFR plus heavy Cd body burden was 9.5 mmHg higher than those with the same Cd body burden and a normal eGFR. By mediation analysis, a 22.7% increase in SBP and a 5% increase in diastolic blood pressure (DBP) were attributable to the effect of Cd on GFR. Thus, a rise of blood pressure appears to be a consequence of GFR loss due to Cd-induced kidney damage. This finding is consistent with a well-known role of the kidney in long-term blood pressure regulation.

Temporomandibular disorders (TMDs) refer to a group of conditions that affect the temporomandibular joint, causing pain and dysfunction in the jaw joint and related muscles. The diagnosis of TMDs typically involved clinical assessment through operator-based physical examination, self-reported questionnaire and imaging studies. To objectivize the measurement of TMD, this study aims at investigating on the feasibility to use machine-learning algorithms fed with data gathered from low-cost and portable instruments to discriminate the presence of TMD in adult subjects. Through this aim, the experimental protocol involved fifty participants, equally distributed between TMD and healthy subjects, acting as control group. The diagnosis of TMD has been performed by a skilled operator through the typical clinical scale. Participants underwent to a baropodometric analysis by using a pressure matrix and the evaluation of the cervical mobility through inertial sensors. Nine machine-learning algorithms belonging to support vector machine, k-nearest neighbours and decision tree were compared. The k-nearest neighbours based on cosine distance was found as the best performing, achieving performance of 0.94, 0.94 and 0.08 for the accuracy, F1-score and G-index, respectively. These findings open the possibility to use such methodology to support the diagnosis of TMDs in clinical environments.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

This research concerns the virtual reconstruction and technical constructive analysis of the emblematic and disappeared Matriz church of Ambato city, whose structure was demolished after the collapse of its vaults in the 1949 earthquake, about which it was said to have had deficiencies in its construction. Through an exhaustive historical review of documents and images, its constructive hypothesis was achieved, and using photogrammetry technique, its virtual reconstruction was obtained, where, through the interpretation and understanding of the generated plans, the verification of its technical and constructive characteristics associated with its hypothetical mechanical behavior inherent to its stone construction was carried out. For the structural study, the principle of the Limit Analysis of Structures was used, where through a graphic static approach, the technical stability conditions of a masonry structure are established, in this case, to give an interpretation to the possible poor execution of the church's work, and eventual cause that could have contributed to the collapse of its vaults.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

The performance analysis of the internal/external flows around a high speed vehicle in near-space is fundamental and critical to the configuration and structure design for high speed aircraft. In this paper, the two-dimensional coupled implicit Reynolds Average Navier-Stokes (RANS) solver and RNG k–ε turbulence model is employed to numerically simulate the flow field of an integrated high speed vehicle. The flow field are divided three parts to solve separately and compared with that solved by integrated simulation. The flow field are decomposed to save computer storage and simulation time. The first part is inlet/isolator, the second part is combustion chamber and the third is nozzle. In the computation process, the outlet condition of isolator is endowed to the inlet boundary of combustion chamber and the outlet boundary of combustion chamber is endowed to the inlet boundary of nozzle, then the whole flow field of integrated high speed vehicle is solved. Aerodynamic characteristic of fragment-computation and integration-computation is comparatively analyzed at different angles of attack, the results show that the maximum deviation of lift coefficient obtained by fragment-computation is less than 3% compared with that by integration, the maximum deviation of drag coefficient fragment-computation is less than 5% compared with that by integration, while pitching moment coefficient deviation less than 12%. However, for simulation time-consumption, the time used by fragment-computation reduces 45% compared with integration-computation. Meanwhile, by components force analysis, it can be concluded that the aerodynamic property of inlet/isolator can been obtained separately and hardly effected by other parts.

Pressure ulcers carry a significant risk in clinical practice and require effective preventive measures. This paper proposes a practical and interpretable approach to estimate the risk levels of pressure ulcers using decision tree models. In order to address the common problem of imbalanced learning in nursing classification datasets, various oversampling configurations are analyzed to improve data quality prior to modeling. The decision trees built are based on three easily identifiable and clinically relevant pressure ulcer risk indicators: mobility, activity and skin moisture. Their analysis allows nursing professionals to predict the risk levels of pressure ulcer and make informed decisions about patient care. Additionally, this research introduces a novel tabular visualization method to enhance the usability of the decision trees in clinical practice. The approach proposed aims to support nursing professionals in making timely decisions regarding the appropriate preventive interventions according to the risk levels of pressure ulcers, thus improving patient outcomes and healthcare costs. The usefulness and effectiveness of the models presented make them a valuable resource for nursing care in the prevention of pressure ulcers.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

Sodium glucose cotransporter 2 inhibitors (SGLT2i) are currently available for the management of type 2 diabetes mellitus. SGLT2i act by inhibiting renal SGLT2, thereby increasing glucosuria and lowering serum glucose. Recent trials are emerging supporting a role for SGLT2i irrespective of the diabetic status pointing towards that SGLT2i have other mechanisms of actions beyond blood sugar control. In this review, we will shed light on the role of this group of medications that act as SGLT2i in non-diabetics focusing on pre-clinical and clinical data highlighting the mechanism of renoprotection and effects of SGLT2i in the non-diabetic kidneys.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

Auger-emitting radionuclides exemplified by Pd-103, exhibit considerable therapeutic potential in cancer treatment due to their heightened cytotoxicity and localized biological impact. Despite these advantages, the separation of such radionuclides presents a complicated challenge, requiring intricate and time-intensive "wet chemistry" methods attributed to the exceptional chemical inertness of the associated metals. This study proposes an innovative solution to this separation challenge through the design and implementation of a radionuclide separation equipment (RSE). The equipment employs a dry distillation approach, capitalizing on differences in partial vapor pressures between irradiated and resulting radioactive metals, with a diffusion-driven extraction method applied to separate Pd-103 radionuclides generated via proton irradiation of Rh-103 at the ATOMKI MGC-20 cyclotron. Optimization endeavors focused on determining the optimal temperature for effective metal separation, adjusting diffusion, evaporation, and deposition rates, as well as addressing chemical impurities. Calculations indicate 17 % ± 2 % separation efficiency with our RSE. Approximately 77% ± 2% and 49% ± 2% of the deposited Pd-103 were isolated on substrates of Nb foil and ZnO-covered W disk, respectively. The proposed innovative dry distillation method that has been experimentally tested, offers a promising alternative to conventional separation techniques, enabling enhanced purity and cost-efficient cancer treatment strategies.

Abstract:Background: Foot ulcers, especially dorsal foot ulcers caused by straps in footwear, can lead to discomfort, pain, and severe complications, particularly in individuals with diabetes and leprosy. While plantar foot pressure measurements have been extensively studied, research on the impact of strap-induced pressure on the dorsal foot aspect remains limited.Research question: The main research question of this prospective study is: Does the implementation of a rolled inner seam strap design (RIS) in flip-flops result in reduced pressure at the toehold area compared to traditional strap designs (Control) in healthy volunteers?Methods: We studied healthy female volunteers, with 10 feet (5 left and 5 right) per arm of the study. Two types of flip-flops, RIS and Control, were compared in a standardized 5-step walk trial on a hardwood floor. Pressure at the toehold was measured using Pressure Sensitive Switches with portable, accurate, ultra-thin pressure sensors. Paired t-tests compared the maximum pressure at the toehold between RIS and Control flip-flops (p < 0.05).Results: The study revealed a statistically significant difference in pressure at the toehold between the RIS and Control flip-flops (p = 0.0014). The mean difference of -40.90 grams (95% CI: -61.22 to -20.58) indicated that the RIS exerted significantly lower pressure than the Control flip flops. The RIS group had a mean pressure of 29.30 grams. The Control group had a mean pressure of 70.20 grams at the toehold area.Significance: The findings of this study have significant clinical implications for individuals at risk of foot ulcers, particularly those with neuropathic conditions such as diabetes and leprosy. The implementation of the RIS design in flip-flops may offer a practical and cost-effective solution to reduce strap-induced pressure and mitigate the risk of strap-related foot ulcers, especially in resource-limited settings where comprehensive foot care is lacking.

In the realm of virtual and augmented reality (VR/AR) and teleoperation applications, haptic feedback plays a role in enhancing task performance. One of the main goals of this study is to simplify haptic device hardware while improving its capacity to provide various stimuli at different intensities. In response to these challenges, this research introduces the Pneumatic Unit Cell (PUC), a soft-pneumatically driven device—a hollow silicone cylinder with the ability to provide both static pressure and vibrotactile feedback. Furthermore, Pneumatic Unit Cell's design simplicity has the potential for scalability, modularity, and the flexibility to mount the device on any part of the human body. The focus of the current paper is to study PUCs as an actuator and lay the foundation for future perceptual studies. The characterization studies encompass fabrication and verification of fabrication accuracy through dimensional measurements, characterizing PUCs under static pressure conditions (measuring free deflection and blocking force), and frequency conditions (measuring free deflection). In the static pressure conditions, we applied pressures ranging from 0 to 40 KPa to measure free deflection and from 0 to 30 KPa to measure blocking force. In the frequency conditions, we applied pressures of 10, 20, and 30 KPa, with inflation/deflation rates varying between 0.5 Hz and 100 Hz. The measurements of free deflection under static pressure conditions revealed that 0.9 mm and 1.2 mm PUCs exhibit a linear increase of free deflection with increase in inflation pressure. The results of free deflection measurements under the frequency conditions indicate a direct relationship between free deflection magnitude and applied pressure. The results also demonstrate an inverse relationship to the frequency of inflation/deflation. The characterization results demonstrate a broad range of free deflection observed under both static pressure and frequency conditions, encouraging the potential application of Pneumatic Unit Cell actuators as haptic devices.

Nondestructive determination of the neutron irradiation induced embrittlement of nuclear reactor pressure vessel steel is a very important and recent problem. In the frame of the so called NOMAD project, funded by the Euratom research and training program, novel nondestructive electromagnetic testing methods were applied for inspection of irradiated reactor pressure vessel steel. In this review the most important results of this project are summarized. Different methods were used and compared with each other. Measurement results were compared with the destructively determined ductile to brittle transition temperature (DBTT) values. Three magnetic methods: 3MA (micromagnetic, multiparameter, microstructure and stress analysis), MAT (magnetic adaptive testing) and Barkhausen noise technique (MBN) were found as the most promising techniques. The results of these methods were in good confidence with each other. Good correlation was found between the magnetic parameters and the DBTT values. The basic idea of the NOMAD project is to use a multi-method/multi-parameter approach and to focus on their synergies that allows to recognise the side effects therefore supressing them at the same time. Different types of Machine Learning (ML) algorithms were tested in competition and their performances were evaluated. The important outcome of the ML technique is that not only one, but several different ML techniques could reach required precision and reliability, i.e. to keep the DBTT prediction error lower than +/-25°C threshold, which was previously not possible for any of the NDE methods as single entities. A calibration/training procedure was carried out on the merged outcome of testing methods with excellent results to predict transition temperature, yield strength and mechanical hardness for all investigated materials. Our results, achieved within NOMAD project can be useful for the future potential introduction of this (and in general, any) nondestructive evolution method.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

In recent years, strain sensors have penetrated various fields. The capability of sensors to convert physical signals into electrical signals is of great importance in healthcare. However, it is still challenging to obtain sensors with high sensitivity, large operating range and low cost. In this paper, a stretchable strain sensor made of a double-layer conductive network, including a biomimetic multilayer graphene-Ecoflex (MLG-Ecoflex) substrate and a multilayer graphene-carbon nanotubes (MLG-CNTs) composite up-layer was developed. The combined action of the two layers led to an excellent performance with an operating range of up to 580% as well as a high sensitivity (gauge factor (GFmax) of 1517.94). In addition, a pressure sensor was further designed using the bionic vein-like structure with a multi-layer stacking of MLG-Ecoflex/MLG-CNTs/MLG-Ecoflex to obtain a relatively high deformation along the direction of thickness. The device presented a high sensing performance (up to sensitivity of 0.433 kPa-1), capable of monitoring small movements of the human body such as vocalisations and gestures. The good performance of the sensors together with a simple fabrication procedure (flip-molding) make it potential for some applications, for example, human health monitoring and other areas of human interaction.

This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

Background: Along with sarcopenia, delayed blood pressure (BP) recovery after standing and orthostatic hypotension (OH) are among key clinical challenges associated with ageing. Previous studies have reported an association between sarcopenia and delayed orthostatic BP recovery and OH. However, the haemodynamic mechanisms underlying this association remain unclear. Methods: 107 attendees to a falls and syncope clinic aged 50+ years underwent an active stand test with non-invasive beat-to-beat haemodynamic measurement. Hand grip strength and 5-chair stands time were measured. Muscle mass was estimated using bioelectrical impedance analysis, and participants were classified as non-sarcopenic and sarcopenic. Mixed effects models with linear splines were used to model the effect of sarcopenia status on Modelflow®-derived mean arterial pressure (MAP), cardiac output (CO), total peripheral resistance (TPR), stroke volume (SV) and heart rate (HR) after standing, while controlling for potential confounders. Results: Sarcopenia was associated with: attenuated recovery of MAP in the 10-20s period after standing (β -0.67, P<0.001); attenuated rise to peak (0-10s) and recovery from peak (10-20s) of CO (β -0.05, P<0.001; β 0.06, P<0.001); attenuated recovery (10-20s) of TPR from nadir (β -0.02, P<0.001) and attenuated recovery from peak (10-20s) of SV (β 0.54, P<0.001). HR was not significantly associated with sarcopenia status at any time interval after standing. Conclusion: The attenuated BP recovery after standing seen in sarcopenia appears to be driven by initial diminished peak of CO followed by attenuated recovery of CO from peak and TPR from nadir. The CO finding appears to be driven by SV rather than HR. Potential mechanisms for these findings include: cardio-sarcopenia, the effects of sarcopenia on the autonomic nervous system and/or the skeletal muscle pump.

Autonomic dysregulation is associated with cardiovascular consequences in obstructive sleep apnea (OSA). This study aimed to investigate the effect of acute continuous positive airway pressure (CPAP) treatment on autonomic activity and to identify factors contributing to the heart rate variability (HRV) changes in OSA. Frequency domain HRV parameters were calculated and compared between the baseline polysomnography and during the CPAP titration in 402 patients with moderate to severe OSA. There were significant reductions in total power, very low-frequency band power, low-frequency band power, and high-frequency band power during the CPAP titration as compared to the baseline polysomnography. This tendency was more pronounced in men than in women, and in patients with severe OSA than those with moderate OSA. Multivariate analysis found that changes in apnea-hypopnea index and oxygen saturation were significantly associated with changes in sympathetic and parasympathetic activity, respectively. This study demonstrated that HRV parameters significantly changed during the CPAP titration, indicating a beneficial effect of CPAP in restoration of sympathetic and parasympathetic hyperactivity in OSA. Prospective longitudinal studies should determine whether long-term CPAP treatment aids in maintaining the long-lasting improvement of the autonomic functions, thereby contributing to the prevention of cardiovascular and cerebrovascular diseases in patients with OSA.

To achieve a fast testing on barrier properties of organic coatings, immersion test, AC-DC-AC test, and coupled test of AC-DC-AC with hydrostatic pressure were conducted in seawater for a glass flake epoxy coating. Electrochemical impedance spectroscopy (EIS) was used to characterize the degradation processes of the coating during the tests, and the surface of the coating was analyzed using optical microscope, scanning electron microscope (SEM) and Fourier transform infrared spectrometer (FTIR). The results show that the periodically cathodic polarization coupled with high hydrostatic pressure can accelerate the degradation of the coating by facilitating the diffusion and uptake of electrolyte and the delamination of the coating. The coupled test method has the largest acceleration due to the synergetic effect of AC-DC-AC and hydrostatic pressure.

We presents results obtained from the numerical simulation of the gas-phase chemical kinetics in atmospheric pressure air non-equilibrium plasmas. In particular we have addressed the effect of pulsed operation mode of a planar dielectric barrier discharge. As it was conjectured, the large difference in the time scales involved in the fast dissociation of molecules in plasmas and their subsequent reactions to produce stable chemical species, makes the presence of a continuously repeated plasma production stage unnecessary and a waste of electrical power and efficiency. Results on NOx remediation, ozone production, water vapor and ammonia dissociation are discussed. A few comparisons with experimental findings in a dielectric barrier discharge reactor already used for applications is briefly addressed too. Our results clearly indicate a pattern for the optimization of the discharge using a carefully designed repetition rate and duty-cycle.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

Introduction: There is no standardised, universal method to assess physical conditions such as pressure in the pelvicalyceal system in real time during RIRS (retrograde intrarenal surgery). Therefore, the problem concerning increased pressure in the upper urinary tract during the procedure is underestimated. Moreover, it potentially may cause micro-damage and longer postoperative recovery. The aim of this study was to evaluate intrapelvic pressure (IPP) during RIRS procedures. Materials and methods: The 3D printed models of the pelvicalyceal system were printed based on CT-scan of real patient. They were used to perform 50 RIRS procedures with laser lithotripsy of artificially synthesised kidney stones with two different sizes of ureteral access sheath-UAS (10/12Fr vs. 12/14Fr) together with different energy settings generated by the holmium:YAG laser. IPP monitoring during RIRS was performed with the use of the PressureWire X Guidewire compatible with the CoroFlow system. Results and Conclusions: The results showed that high IPP of up to 400 cmH2O would be achieved using a 10/12Fr UAS, while the use of a 12/14Fr UAS would significantly reduce the peak pressure to approximately 100 cmH2O, hence the size of the UAS is a pivotal factor of the IPP generated during the procedure.

This paper investigates the impact of sediment deposition and inflow conditions on horizontal impact pressure and frequency analysis of bridge deck vibrations during flooding. Flooding-induced pressure and vibrations contribute to bridge collapse, and sediment deposition influences water flow and impact pressure. The study explores the relationship between sediment deposition height and impact pressure, revealing a significant increase as sediment approaches 50% of bridge deck clearance. Sediment amplifies impact pressure response to flow velocity changes. The dimensionless sediment deposition height has a greater influence on impact pressure compared to the inflow Froude number. Two distinct frequencies, dominant and secondary, are identified for impact pressure and water level fluctuations. Dominant frequencies positively correlate with sediment deposition height and Froude number, indicating an increasing trend. Secondary frequencies remain stable (0.31-0.58 Hz). These findings enhance understanding of flow dynamics and bridge-flow interaction in sediment-deposited channels, providing theoretical support for evaluating and managing disasters related to bridges in such environments. Overall, this research contributes to the field of bridge engineering and supports improved design and maintenance practices for bridges exposed to sediment-deposited channels.

Background: To examine the effects of continuous positive airway pressure (CPAP) therapy on central corneal thickness (CCT) in patients with obstructive sleep apnea (OSA) followed for 12 months. Methods: Participants were patients with OSA and an indication for CPAP who were enrolled after diagnosis and graded according to the apnea hypopnea index (AHI) determined in an overnight polysomnography. Each subject underwent a full ophthalmologic examination including ultrasound pachymetry (USP) with an SP3000 USP (Tomey Inc) at the time points just before CPAP onset, and after 3 and 12 months of CPAP treatment. Results: The study sample comprised 40 eyes of 20 patients. Adherence to CPAP was adequate (5.23 ± 1.77 h/night). After receiving 12 months of CPAP, positive correlation was observed between hours of CPAP use and CCT (r = 0.382, p = 0.015). Intermittent hypoxemia pre-CPAP or hypoxia severity pre-CPAP were also positively correlated with the CCT recorded after 12 months of CPAP (r = 0.394, p = 0.012; r = 0.324, p = 0.041). Significant correlations were, however, not observed after only 3 months of CPAP treatment. In addition, compared to measurements at 3 months, intraocular pressure was higher after 12 months of treatment. Conclusions: Our findings indicate that 12 months of correct adherence to CPAP are needed to detect significant CCT thickening, and that the greater the pre-CPAP hypoxemia, the greater the capacity for an increase in CCT to be produced in response to 12 months of this therapy.

Physical exercise is the greatest stress on the cardiovascular system, not only in humans but also in all vertebrates. Consequently, the cardiovascular response cannot be thought of as having only one "anthropocentric" interpretation. The modulation of cardiac output (Q) in response to exercise in the five major groups of vertebrates exhibits considerable variability. Moreover, the response of the heart rate (HR) and the stroke volume (SV), the fundamental factors that cause the rise in Q, is also highly variable. The difference in the range of HR is difficult to determine in many vertebrates, both at rest and at maximal effort. Additionally, the increase in SV varies among vertebrates. For example, while rainbow trout and leopards increase their SV by increasing end diastolic volume (EDV), humans do so at the expense of both increasing EDV and reducing end systolic volume (ESV). The variation in arterial pressure that arises during exercise varies notably among vertebrates, such as amphibians, whose blood pressure values do not increase as significantly as in mammals. Such differences in cardiovascular response among vertebrates may be linked to their habitat or living environment. This review aims to analyze the cardiovascular response of vertebrates to physical exercise as the most common stressor.

All-solid-state lithium batteries (ASSLBs) using argyrodite electrolyte materials have shown promise for applications in electric vehicles (EVs). However, understanding the effects of pro-cessing parameters on the ionic conductivity of these electrolytes is crucial for optimizing battery performance and manufacturing methods. This study investigates the influence of electrolyte op-erating temperature, electrolyte operating pressure, electrolyte pelletization pressure, and electro-lyte pelletizing temperature on the ionic conductivity of Li6PS5Cl0.5Br0.5 argyrodite electrolyte (AmpceraTM, D50=10 µm). A specially designed test cell is employed for the experimental meas-urements, allowing for controlled pelletization and testing within the same tooling. The results demonstrate the significant impact of the four parameters on the ionic conductivity of the argy-rodite electrolyte. The electrolyte operating temperature has a more pronounced effect than oper-ating pressure, and pelletizing temperature exerts a greater influence than pelletizing pressure. This study provides graphs that aid in understanding the interplay between these parameters and achieving desired conductivity values. It also establishes a baseline for the maximum pelletizing temperature before undesirable degradation of electrolyte occurs. By manipulating the pelletizing pressure, operating pressure, and pelletizing temperature, battery engineers can achieve the desired conductivity for specific applications. The findings emphasize the need to consider operating conditions to ensure satisfactory low-temperature performance, particularly for EVs. Overall, this study provides valuable insights into processing and operating conditions for ASSLBs utilizing Li6PS5Cl0.5Br0.5 argyrodite electrolyte.

The Macroscopic Mechanical Equilibrium Condition can be shown to be the physical origin of the Equation of State of any material system, then can describe all thermodynamic quasi-equilibrium processes caused by the change of the external temperature and/or mechanical environment. If it cannot be satisfied, the system would be broken.

Considering tumors from an evolucionary perspective, successive tumor cells undergo turnover in response to stressful conditions which pressures tumor cells to adapt to a new environment. Tumor cells uses parts of themselves to communicate and share biological information, known as extracellular vesicles (EV) secretion to promote their survival and “survive to each and every metabolic cost”. Tumor microenvironment (TME) is a miscellaneous of cells, factors, extracellular matrix proteins and EVs. EVs include smalls (<160nm, exosomes) and larger (100-1,000nm, microvesicles) lipid bilayer enclosed packages of biomolecules that are shed by tumors to TME. Tumor-derived extracellular vesicles transfer adaptative stress signaling to recipient cells, reprograming these cells. Heat Shock Proteins (HSP) are more prominent stress response regulators found in exosomes. HSP-loaded exosomes actively reprogram tumor and TME cells to acquire mechanisms that contribute to tumor progression and therapy resistance. The intercellular communication mediated by HSP-loaded EVs favors the escape of tumor cells from, endoplasmic reticulum (ER) stress, hypoxia, apoptosis and anti-cancer therapies. Extracellular HSPs activate and deactivate immune response, induce cell differentiation, changes vascular homeostasis, and help to augment the pre-metastatic niche formation. Here we will explore the EV mechanism of HSP transmission among TME cells and the relevance of these intercellular communications for resistance to therapies in cancer.

Palpation is a simple but effective method to differentiate tumors from healthy tissues. Development of miniaturized tactile sensors embedded on endoscopic or robotic devices are the key toward precise palpation diagnosis and the subsequent timely treatment. This paper reports on the fabrication and characterization of a novel tactile sensor with mechanical flexibility and optical transparency that can be easily mounted on soft surgical endoscopes and robotics. Utilizing the pneumatic sensing mechanism, the sensor offers a high sensitivity of 1.25 mbar and negligible hysteresis, enabling the detection of phantom tissues with different stiffnesses ranging from 0 to 2.5 MPa. Our configuration combining pneumatic sensing and hydraulic actuating also eliminates electrical wiring from the functional elements located at the robot end-effector, thereby enhancing the system safety. The optical transparency path in the sensors together with its mechanical sensing capability open interesting possibility in early detection of solid tumor as well as in the development of all in-one soft surgical robots that can perform visual/mechanical feedback and optical therapy.

(1) Background: High blood pressure is one of the symptoms of stroke, the Self Care Deficit theory by Dorothea Orem focuses on a person's ability to care for himself independently so that the ability to maintain his health and well-being is achieved. There are currently 600 million hypertensive patients worldwide, of which 3 million die every year. Uncontrolled high blood pressure can lead to a 7-fold increase in the chances of stroke. The existence of this condition can be minimized in patients through several innovative interventions, one of which is foot massage. This study aims to determine the effectiveness of stretching and foot massage with lavender oil in stabilizing high blood pressure in stroke patients.(2) Methods: The method used in this research is descriptive. The subjects of this case study were selected according to the inclusion and exclusion criteria of the journal Evidence-Based. Subjects included intervention patients and control patients. Foot massage therapy with lavender oil is done 2 times a day for 10-15 minutes using the effleurage technique after showering in the morning and evening. Stretching is done 2 times a day every 10-15 minutes.(3) Results: The results of the analysis showed that there was a change in blood pressure after the application of stretching and foot massage with lavender oil. From the initial examination, the results showed that the blood pressure of 170/100 mmHg decreased to 140/90 mmHg and the pain scale decreased from 4 to 0.

Objective: One of the major causes of cerebral ventricular shunt failure is proximal catheter occlusion. We describe a novel ventricular cerebrospinal fluid (CSF) flow replicating system that assesses pressure and flow responses to varied degrees of catheter occlusion. Methods: Ventricular catheter performance was assessed during conditions of partial and complete occlusion. The catheters were placed into a three-dimensionally printed phantom ventricular replicating system. Artificial CSF was pumped through the ventricular system at a constant rate of 1 ml/min to mimic CSF flow, with the proximal end of the catheter in the phantom ventricle. Pressure transducer and flow rate sensors were used to measure intra-phantom pressure, outflow pressure and CSF flow rates. The catheters were also inserted into silicone tubing and pressure was measured in the same manner for comparison with the phantom. Results: Pressure measured in the phantom ventricle did not change when the outflow of the ventricular catheter was partially occluded. However, the intraventricular phantom pressure significantly increased when the outflow catheter was 100% occluded. Flow through the catheter showed no significant difference in rate with any degree of partial occlusion of the catheter. At the distal end of the partially occluded catheters, there was less pressure compared with the nonoccluded catheters. This difference in pressure in partially occluded catheters correlated with the percentage of catheter hole occlusion. Conclusions: Our model mimics physiological dynamics of the CSF flow in partially and completely obstructed ventricular catheters. We found that partial occlusion of the catheter had no effect on CSF flow rate, but did reduce outflow pressure of the catheter.

Worldwide, it is estimated that at least 1 in 4 adults suffers from hypertension, and this number is expected to increase as populations grow and age. Blood pressure (BP) possesses substantial heritability, but is also heavily modulated by lifestyle factors. As such, digital, lifestyle-based in-terventions are a promising alternative to standard care for hypertension prevention and man-agement. In this study we assessed the prevalence of elevated and high BP in a Dutch general pop-ulation cohort undergoing a health screening, and observed the effects of a subsequent self-initiated, digitally-enabled lifestyle program on BP regulation. Baseline data were available for 348 participants, of which 56 had partaken in a BP-focused lifestyle program and got re-measured 10 months after the intervention. Participants with elevated SBP and DBP at baseline showed a mean decrease of 7.2 mmHg and 5.4 mmHg, respectively. Additionally, 70% and 72.5% of participants showed an improvement in systolic and diastolic BP at remeasurement. These improvements in BP are superior to those seen in other recent studies. The long-term sustainability and the efficacy of this and similar digital lifestyle interventions will need to be estab-lished in additional, larger studies.

Landslides are serious geological hazards that become a disaster worldwide, causing a large number of casualties and economic losses every year. There are many factors affecting landslide susceptibility, such as rainfall, soil and slope. Each of them has an important role in the process of slope losing stability. In this paper, the effects of rainfall intensity, rainfall pattern, slope gradient and soil type on landslide susceptibility are studied. In the process of rainfall-induced landslide, the relevant physical quantities of soil changes continuously. Their values and processes are closely related to the time of landslide occurrence. Hence, the variation of soil volumetric water content, matrix suction, pore water pressure and total stress throughout the rainfall are measured. As the results, soil type, slope gradient and rainfall intensity have a large influence on landslide susceptibility. The occurrence of landslides has a prerequisite that the slope is greater than or equal to 15°. The rainfall intensity needs to be not less than 80 mm/h. The difference of rainfall pattern also affects the landslide susceptibility. The rainfall pattern with rainfall intensity peak at the later stage is more likely to induce landslide. Coarser soils with gravels are prone to landslides when other conditions are the same. Steeper slopes, stronger rainfall, and coarser soils can all increase the amount of sediment yield.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

Aim: Reporting 3 year outcomes of a community shared care scheme run by specialised independent prescribing (IP) optometrists for stable glaucoma and ocular hypertension (OHT) patients in West Kent, England. Purpose: Shared Care Schemes for glaucoma exist to alleviate the burden on Hospital Eye Services (HES) glaucoma clinics. We studied the effectiveness of community care by highly trained and qualified IP optometrists in terms of disease stability and referral rate into HES.Methods: Retrospective longitudinal review of 200 eyes with stable early to moderate stage glaucoma and OHT followed-up in two specialist optometry practices. Outcome measures included visual field mean deviation (VFMD), intraocular pressure (IOP), changes to treatment and referral rate into HES. Inclusion criteria included all patients with OHT and glaucoma (open angle and primary angle closure) referred for community follow-up. Incomplete data sets were excluded.Results: Mean age 71yrs (range 28 - 93yrs) and equal male: female ratio. n= 159 at year 3. The results for both outcomes showed no significant change from baseline at 12 or 24-month time points. However, a significant change from baseline at 36 months was observed for both outcomes: mean reduction of 0.7 mmHg in IOP, and a mean reduction of 0.3 dB in VFMD. There was a statistically significant change in the number of drops used at 36 months (p=0.001). 11 patients had a change in medication within 3 years. One patient was referred back to HES for uncontrolled IOP and consideration of trabeculectomy.Conclusion: Community follow-up of stable cases of glaucoma and OHT by highly qualified IP optometrists was safe, with stability of disease maintained and few referrals back to HES.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

Therapeutic proteins are used to successfully treat hemophilia, Crohn’s Disease, diabetes, and cancer. Recent product recalls have occurred because of sub-visible particle formation resulting from the inherent instability of proteins. It has been suggested that particle formation is associated with late stage processing steps of filling, shipping, and delivery. Previous works demonstrated that cavitation might occur in therapeutic vials subjected to agitation or accidentally dropped, but that mitigation can be achieved with fluid property manipulation. The goal of this research was to (1) assess the risk of cavitation under common pharmaceutical manufacturing conditions (i.e., pipe contraction and pumps), (2) establish a simple threshold criterion for when particulate will form, and (3) suggest a series of mitigation techniques based on these thresholds. To accomplish these tasks, computational fluid dynamic simulations for a variety of pipe contraction and fluid properties were performed. The results of this research show that reducing the turbulence in a fluid system will reduce the likelihood of cavitation. Additionally, threshold bounds were created that establish a definitive transition at which cavitation will occur.

We successfully designed an optimized plenum fan with a three-dimensional, smooth, curved blade. The optimized model revealed that the static pressure in the channel had been increased uniformly and stably, and the flow separation at the leading edge was significantly reduced. To conclude, the three-dimensional blade stabilized the fluid flow, and the flow friction was reduced by suppressing the flow separation as much as possible so that both the static pressure and the static efficiency were clearly improved in comparison with those of the original model. The static efficiency, as a result, was improved by 6% compared with that of the original model.

Purpose: To evaluate seasonal variation in intra-ocular pressure (IOP) with and without short tear break-up time (SBUT, BUT ≤ 5 s). Methods: This study enrolled 176 patients who visited one of six eye clinics in Japan for IOP measurement at every season. The mean patient age was 67.9 years, including 79 males. We compared the seasonal variation in IOP (mean ± SD) across spring (Mar-May), summer (Jun-Aug), fall (Sep-Nov), and winter (Dec-Feb). Results: The IOP (mmHg) in winter and summer, respectively, was 12.8 ± 3.7 and 12.8 ± 3.1 for non-glaucoma patients without SBUT (n = 47, P = 0.964), 14.8 ± 3.4 and 13.3 ± 3.4 for non-glaucoma patients with SBUT (n = 57, P < 0.001), 14.3 ± 3.2 and 14.1 ± 3.4 for glaucoma patients without SBUT (n = 36, P = 0.489), and 13.3 ± 3.0 and 11.6 ± 2.9 for glaucoma with SBUT (n = 36, P < 0.001). Seasonal variation was largest across the seasons in the glaucoma with SBUT group, and the magnitude of seasonal variation correlated with BUT (β = 0.228, P = 0.003). Conclusions: Seasonal variation tended to be larger in patients with SBUT than those without SBUT.

Background: Sex differences in blood pressure (BP) exist during all reproductive life between women and men whereas a sharper increase in BP occurs after menopause which is associated with increased prevalence of cardiovascular diseases. This study examined cardiovascular and biochemical parameters in perimenopausal women (PW) aiming to investigate the influence of sex on a) office BP and for 24 hours; b) cardiac autonomic modulation; c) redox state by measuring MDA, SOD, and catalase; d) NO_x^- concentration. In addition, aerobic exercise training (AET) was applied for detecting changes in cardiovascular responsiveness during the menopausal transition. Methods: Thirty-one participants were enrolled, healthy PW and age-matched men. Cardiovascular and biochemical biomarkers were evaluated at baseline and after AET (8 weeks of exercise on a treadmill, three sessions/week, duration of 30-40 minutes). Results: At rest, PW presented: a) a lower diastolic BP during daytime; b) a lower absolute and normalized LF component as well as a higher HF normalized component; d) no sex differences for redox biomarkers and NO_x^- concentration. After AET, only PW was responsive in lowering systolic BP that was accompanied by an increase in NO_x^- concentration and SOD activity. Regarding HRV, both groups were responsive to the AET. Conclusions: During the menopausal transition, systolic BP was similar to men whereas cardiac autonomic modulation remained unaltered showing the influence of sex steroids on BP. In Addition, AET was fundamental during the menopause transition by preventing an elevation in BP, minimizing the effects of aging associated with estrogen deficiency on women's cardiovascular health.

Random copolymers made of both (PIM-polyimide) and (6FDA-durene-PI) were prepared for the first time by a facile one-step polycondensation reaction. By combining the highly porous and contorted structure of PIM (polymers with intrinsic microporosity) and high thermomechanical properties of PI (polyimide), the membranes obtained from these random copolymers [(PIM-PI)x-(6FDA-durene-PI)y] showed high CO₂ permeability (> 1047 Barrer) with moderate CO₂/N₂ (> 16.5) and CO₂/CH₄ (> 18) selectivity, together with excellent thermal and mechanical properties. The membranes prepared from three different compositions of two comonomers (1:4, 1:6 and 1:10 of x:y), all showed similar morphological and physical properties, and gas separation performance, indicating ease of synthesis and practicability for large-scale production. The gas separation performance of these membranes at various pressure ranges (100–1500 torr) was also investigated.

The aim of this study is to provide the scientists with a straightforward correlation that can be applied for predicting the Fanning friction factor and consequently the pressure drop during blood flow in small caliber vessels. Due to the small diameter of the conduit, the Reynolds numbers are low and thus the flow is laminar. The study has been conducted using CFD simulations validated with relevant experimental data acquired using an appropriate experimental set-up. The experiments concern pressure drop measurement during the flow of a blood analogue that follows the Casson model, i.e. an aqueous glycerol solution that contains a small amount of xanthan gum and exhibits similar behavior to blood, in a smooth, stainless steel microtube (L=5.6cm and D=400 μm). The interpretation of the resulting numerical data led to the proposal of a simplified model that incorporates the effect of the flow rate, the hematocrit value (35-55%) and the vessel diameter (300-1800 μm) and predicts with better than ±10% the Fanning friction factor and consequently the pressure drop during laminar blood flow in small caliber vessels.

Purpose: To evaluate three different microincisional ab interno trabeculectomy procedures in a porcine eye perfusion model. Methods: In perfused porcine anterior segments, 90 degrees of trabecular meshwork (TM) were ablated using the Trabectome (T; n = 8), Goniotome (G; n = 8), or Kahook device (K; n = 8). After 24 hours, additional 90 degrees of TM were removed. Intraocular pressure (IOP) and outflow facility were measured at 5 µL/min and 10 µL/min perfusion to simulate an elevated IOP. Structure and function were assessed with canalograms and histology. Results: At 5 µL/min infusion rate, T resulted in a greater IOP reduction than G or K from baseline (76.12% decrease versus 48.19% and 47.96%, P = 0.013). IOP reduction between G and K was similar (P = 0.420). Removing another 90 degrees of TM caused an additional IOP reduction only in T and G but not in K. Similarly, T resulted in the largest increase in outflow facility at 5 µL/min compared with G and K (first ablation: 3.41 times increase versus 1.95 and 1.87; second ablation: 4.60 versus 2.50 and 1.74) with similar results at 10 µL/min (first ablation: 3.28 versus 2.29 and 1.90 (P = 0.001); second ablation: 4.10 versus 3.01 and 2.01 (P = 0.001)). Canalograms indicated circumferential flow beyond the ablation endpoints. Conclusions: T, G and K significantly increased the outflow facility. In this model, T had a larger effect than G and K.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

NACA 0015 and NACA 4415 aerofoil are most common four digits and broadly used aerodynamic shape. Both of the shapes are extensively used for various kind of applications including turbine blade, aircraft wing and so on. NACA 0015 is symmetrical and NACA 4415 is unsymmetrical in shape. Consequently, they have big one-of-a-kind in aerodynamic traits at the side of widespread differences of their utility and performance. Both of them undergo the same fluid principle while applied in any fluid medium giving dissimilar outcomes in aerodynamics behavior. On this work, experimental and numerical investigation of each NACA 0015 and NACA 4415 is done to decide their performance. For this purpose, aerofoil section is tested for a prevalence range attack of angle (AOA). The study addresses the performance of NACA 0015 and NACA 4415 and evaluates the dynamics of flow separation, lift, drag, pressure and velocity contour and so on. This additionally enables to layout new optimistic aerofoil, which is critical to enhance the efficiency and performance of an aircraft in terms of lift enhancement and drag reduction.

Most available studies on the mechanical properties of apples lack the comprehensive results needed for the construction and validation of FEM models. Researchers typically focus on either the flesh and epidermis or the whole fruit, often overlooking the maturity stage of the examined apples. They usually report only firmness or the starch index as indicators of maturity. Furthermore, many studies use store-bought apples, which is impractical for industrial applications since this fruit have already undergone various treatments before reaching the shelf. This article aims to determine the mechanical properties of apples necessary for constructing FEM models that are both adequate and useful for the industry. The new Polish apple variety, Chopin, was selected as the research material. The study was conducted for three stages of apple maturity: development, ripening, and senescence. Mechanical properties of the flesh and skin were determined as material data for FEM models. Force-displacement curves and pressure-force functions were examined for future model validation. Using micro-computed tomography, the bruise volumes of fruit subjected to 20%, 50%, and 80% of the destructive force were determined. Significant differences were found between apples in the senescence stage and those in the development and ripening stages. Results of Micro-Ct and the results of modified and real compression tests of whole fruit have allowed us to formulate the research hypothesis regarding the influence of flesh cracking (characterized by local drops of force), influencing the bruise visibility and detection.