This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

The Wolfram (W), Silicium (Si) and Molybdenum (Mo) doped Co-Cr biomedical alloy were fabricated by additive manufacturing method, which is part of powder metadology. The mixture of Wolfram (W), Silicium (Si), Chrome (Cr) and Cobalt (Co) alloy is known good wear and corrosion resistance among of biomedical applications. By addition of Molybdenum (Mo) into the structure of alloy, the structure become more stbale also increase the corrosion and wear resistance. In addition, the effects of secondary annealing process on the alloy were investigated. The microstructure of the produced alloy was analyzed by X-ray diffraction method XRD, Energy Dispersive X-Ray Analysis EDX and scanning electron microscope SEM. Moreover, Electrochemical corrosion test, micro hardness and density measurements were performed to investigate the mechanical properties of the alloy. As a result of the analyzes, the effects of Molydenum (Mo) doped and secondary annealing on the microstructure and mechanical properties of bioalloying were determined.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

Natural events such as floods, fires, tsunamis, earthquakes and others have nowadays caused serious damage to human beings and nature. The precise detection of these natural events and especially the earthquake has nowadays become the focus of many computer and geoscientific researchers. Computer science and machine learning algorithms have revolutionized early detection and prediction of these events. Hence, a fuzzy method has been initially used in this article to enhance the authenticity of data based on application of effective variables and then combination of neural network algorithms of the MLP perceptron and radial network of RBF in form of a collective learning system in order to more accurately identify seismic events on a small scale. It was observed after simulating the proposed method that the proposed method has significantly improved based on actual error and root-mean-square error (RMSE) criteria compared to basic methods.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The occurrence of potential spikes in a cell is a sign of life, and it is called action potential. There is a common notion that neuron signal conduction is the conduction of action potential. Hence, action potential is a typical and essential life activity. However, such potential spikes occur even in simple nonliving systems. According to the experimental observations by Pollack, structured water molecules can generate a negative potential environment. From this observation, the potential spike generation process for both living and nonliving systems caused by ion and water molecule adsorption-desorption process could be explained in this paper. So, taking into consideration the electrically neutral water molecules,the action potential generation mechanism could be explained. It is a fully inanimate model. Hence, the action potential may not be a life activity. Here, the role of water molecules in life is investigated further. It was found that the phase transition of the membrane is involved in the neuron signal conduction, but the membrane phase transition could be due to the change of state of the water molecules, which forms a large-scale structure in the cavities created by a number of lipids.

Rapid technological advancements in information communication technologies have enabled water resource data collection at greater spatial and temporal scale. However, this water data is often limited to the purposes of its primary collection, and limits decisions made by stakeholders towards sustainable urban water management. This empirically focused research paper examines how water practitioners involved in strategic planning can capture additional values from integrating different water data. Furthermore, the perception of 22 urban water practitioners across Australia are presented, regarding the importance of and difficulty in using water data for strategic planning, and the necessary steps for achieving integrated water management practices. Interviewees perception revealed gaps in available water resource data (i.e. water quality, ground water, stormwater, and urban water use), and limitations of industry guidelines for operating within existing governance frameworks. Overall, the research highlights the Australian urban water sector’s perception of water data’s crucial role in representing stakeholders interest; however, changes made in water data’s collection are required for an integrated water management approach. Implications for future open water data standard are discussed.

Water scarcity is significantly increasing water stress in Africa and some parts of the world. This is due to human induced factors such as climate change, increase of human population that raises demand which outstrips food availability, and put great changes of land use which results in changes of hydrological mechanics and water availability as whole. The investigation was through literature review and it tries to examine the criticality of water scarcity in Africa regions, and the major factors that mastermind this menace. Also possible strategies that can be promptly used to manage water scarcity at domestic level and in agriculture are described in this paper, not with standing the fact that agriculture sectors in Africa and the rest of the world remain the utmost vulnerable enterprise to water scarcity and withdrawal on the planet earth.

Achieving water security and availability for all is among the principle agenda of the UN-Sustainable Development Goals. To achieve the goal of water security, particularly in rapidly expanding cities, identification of safe and sustainable water resources is an absolute necessity. The paper conducts an exploratory investigation in the hydro geochemical characteristics of groundwater and thereby, assess the suitability of groundwater as an alternative and reliable resource for public water supply in the Indian city of Surat. A total of 33-groundwater samples, selected on the basis of aquifer depth, land use signatures, were collected from open, bore, dug wells and hand pumps. After the hydrogeochemical analysis, the study evaluated the present state of the groundwater quality and determined the spatial distribution of groundwater quality parameters such as hardness, electrical conductivity, Cl −, pH, SO42-, and NO3 − concentrations. An interpolation technique, known as ordinary kriging, was used to acquire the spatial distribution of parameters of groundwater quality parameters. Based on the permeability index, result showed that 80% of the sampled groundwater quality falls under excellent class i.e. category I with PI value ranging from 1-24%, whereas the rest 20% of the samples has fallen under good class i.e. category II with PI value ranging from 25 to 75% on the suitability of water for irrigation. The results of this study outlines the unsustainability of groundwater for direct consumption, especially without any improved onsite water treatment, but it is appropriate for the irrigation purposes.

The quantity, makeup, and distribution of bodily fluids have a significant impact on the cognitive and physiological health of individuals. The knowledge of an individual on the recommended daily Total Water Intake (TWI) by the World Health Organization (WHO) and the European Food Safety Authority (EFSA) influences the practice of Adequate Water Intake (AWI). To sufficiently measure the knowledge of hydration, it is expedient to develop and validate a scale to adequately measure knowledge of the recommended daily Total Water Intake (TWI). Hence, this study aims to develop an 11-items scale to measure the Knowledge of hydration (KH-11) and evaluate its psychometric properties among foreign student at Óbuda University, Hungary. The novelty of this study is the development of an 11-item scale to measure the knowledge of hydration among students at Óbuda University, Hungary.

Hydrogenated water has emerged as a novel approach in the field of health and wellness. It is be-lieved to have potent antioxidant properties that can neutralize harmful free radicals in the hu-man body. It has also been shown to be beneficial in mitigating oxidative stress-induced damage through its anti-inflammatory and anti-apoptotic pathways. We aim to conduct a systematic re-view to evaluate the potential benefits of hydrogenated water. The review protocol was uploaded on PROSPERO. After the initial search criteria, the articles were reviewed by two blinded inves-tigators, and a total of 25 articles were included in the systematic review. The potential benefits of hydrogenated water on various aspects of health, including exercise capacity, physical endurance, liver function, cardiovascular disease, mental health, COVID-19, oxidative stress, and anti-aging research, are a subject of growing interest and ongoing research. Although preliminary results in clinical trials and studies are encouraging, further research with larger sample sizes and rigor-ous methodologies is needed to substantiate these findings. Current research needs to fully ex-plain the mechanisms behind the potential benefits of hydrogenated water. Continued scientific exploration will provide valuable insights into the potential of hydrogenated water as an adjunc-tive therapeutic approach in the future.

Fresh water is an increasingly scarce resource in both urban and rural developments. As a response to this challenge, non-potable water reuse is on the rise. This research explored a potential off-grid system for water purification, consisting of a staircase wetland with terracotta pot plants working as a filter for greywater. The study further investigated the physicochemical properties of the greywater and the soil before and after the wetland purification. Results showed that the filtered water satisfied all requirements for water reuse, e.g., pH, turbidity, and total coliforms. The research then uniquely investigated the effect of greywater on the soil biodiversity and soil biomass using soil DNA extraction and the tea bag index testing method. The filtered greywater absorbed by soil decomposed the soil faster and stabilized it better compared to tap water-absorbed soil or unfiltered greywater. The DNA generation sequencing revealed no significant differences in alpha diversity between control and treatment samples. The beta diversity differences were significant. This nature-based solution can lead to reduced load on the sewage system, resulting in less wastewater generation.

Everyone should therefore consistently get access to enough and safe water. The operation of the existing distribution network as well as the proper optimization and implementation of the new distribution systems are required for a sufficient and safe water supply. In Sekota town sufficient amount of water was not reached to the beneficiaries due to shortage of water at the source. The primary goal of this study was to evaluate the performance and optimize the existing Sekota water supply distribution system using Bentley Water GEMS.The system's hydraulic modeling is carried out by considering as a continuous supply system, and the evaluation procedure used the extended period simulation approach after calibration was done. Calibration is used to ensure the performance of the model using the observed pressure values. The output of the existing system shows pressure is very high means above the maximum pressure and velocity is very low at peak hour demand. The results of velocity and pressure before optimization have negative effect on the performance of the system. The number of pipes and junctions their velocities and pressures which were in admissible ranges are 15 and 42 pipes for velocities and zero and 59 junctions for pressure before and after optimization were evaluated respectively.

Growing water shortages for large regions of the arid regions of the world, are likely to become more recurrent as climate change impacts grow. Countries across the world are facing water security difficulties that stem from population growth, urbanization, and rapid industrialization. The use of behavioral nudges methods implemented to encourage a socially desired behavior at a low to zero cost, has been an effective method at reducing water consumption in places where they have been deployed. For example, studies in California USA, Barcelona Spain, and Australia indicate that adoption of nudges give significant positive results in water consumption reduction. We describe some of the barriers that make it difficult to implement behavioral nudges to address the water crises in Sub-Saharan Africa (SSA). We investigate the literature available in Sub-Saharan Africa and discover that the application of behavioral nudges has been sparingly used for reasons that are not obvious at first glance. Second, we find that the potential impediments to the use of behavioral nudges in SSA to be awareness, inadequate access to science and technology, political systems that are poorly suited for implementing nudging, abundance of multiple ethnic groups that speak different languages, along with other barriers that could challenge implementation of behavioral nudges. In light of those barriers, we present a conceptual model with a potential to address these barriers to behavioral nudging a workable solution in SSA.

The specialisation and intensification in agriculture have increased the productivity but have also led to the spread of monocultural systems, simplifying production and reducing genetic diversity. The purpose of this study was to propose crop diversification as a tool to increase biodiversity and achieve sustainable and resilient intensive agriculture, particularly in areas with water scarcity. In this paper, a combined Life Cycle Assessment (LCA) and Life Cycle Costing (LCC) was applied to evaluate the environmental and economic sustainability of a differentiated system of cultivation (pomegranate, almond and olive), according to modern intensive and superintensive cropping systems. Based upon the results obtained, it is deduced that pomegranate cultivation generated the highest environmental load, followed by almond and olive. From the financial analysis, it emerged that almond is the most profitable, followed by pomegranate and olive.

This work investigates the utility of the National Oceanic and Atmospheric Administration’s National Water Model (NWM) for water management operations by assessing the total inflow into a select number of reservoirs across the Central and Western U.S. Total inflow is generally an unmeasured quantity, though critically important for anticipating both floods and shortages in supply over a short-term (hourly) to sub-seasonal (monthly) time horizon. The NWM offers such information at over 5,000 reservoirs across the U.S., however, its skill at representing inflow processes is largely unknown. The goal of this work is to understand the drivers for both well performing and poor performing NWM inflows such that managers can get a sense of the capability of NWM to capture natural hydrologic processes and in some cases, the effects of upstream management. We analyzed the inflows for a subset of Bureau of Reclamation (BoR) reservoirs within the NWM over the long-term simulations (retrospectively, seven years) and for short, medium and long-range operational forecast cycles over a one-year period. We utilize ancillary reservoir characteristics (e.g. physical and operational) to explain variation in inflow performance across the selected reservoirs. In general, we find that NWM inflows in snow-driven basins outperform those in rain-driven, and that assimilated basin area, upstream management, and calibrated basin area all influence the NWM’s ability to reproduce daily reservoir inflows. The final outcome of this work proposes a framework for how the NWM reservoir inflows can be useful for reservoir management, linking reservoir purposes with the forecast cycles and retrospective simulations.

Natural spa springs are diffused all over the world and their use in pools is known since ancient times. This review underlines the cultural and social spa context focusing on hygiene issues, public health guidelines and emerging concerns regarding water management in wellness or recreational settings. The question of the "untouchability" of therapeutic natural waters and their incompatibility with traditional disinfection processes is addressed considering the demand for effective treatments that would respect the natural properties. Available strategies and innovative treatments are reviewed, highlighting potentials and limits for a sustainable management. Alternative approaches comprise nanotechnologies, photocatalysis systems, advanced filtration. State of the art and promising perspectives are reported considering the chemical-physical component and the biological natural complexity of the spa water microbiota.

International basins are divided into sub-basins that are managed at the national and local levels, within the territory of each country, before reaching the level of international concern. The management of international basins could be developed using an integrated water management, based on multi-level governance model in which many actors are involved, from local to international scale. However, in the La Plata River Basin this model is not working, even with international agreements such as the La Plata Basin Treaty, which was signed in 1969. The understanding of political interests behind the law helps to explain its inefficiency. Therefore, considering the lack of a systemic view in an international watershed, it could be possible to have accumulating effects caused by the transformations of watercourses in the sub-basins. Then, the 2014 water crisis in the State of São Paulo, Brazil, is an example of the possible consequences arising from the lack of an integrated water management in the La Plata River Basin. Finally, this article demonstrates that the only way to have water resources utilization efficiency in an international basin is considering it as an integrated ecosystem, in order that any local problem may affect the whole basin.

Water supply is a mandatory service for Tanzanians from respective legal public water utilities, and their sustainability reflects implementations of best management strategies at a local level. The objective of this study was to assess current approaches used in water quality and quantity management in Tanzania. This was achieved through secondary water data tends, on-site water quality assessments, visits of respective water supply and sanitation authorities, and assessment of their performances. It was observed that water supplied in rural-based authorities was quite different from that supplied in an urban setting as far as quality and quantity is concerned, urban-based supplies being of assistance to users over rural ones. A new strategy on water management is presented for sustainable water supply in Tanzania; it is based on controlling groundwater abstractions and preference of surface water in public water supplies. Rural water supply management must learn several practices realized at urban supplies for the betterment of respective majority water users.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

In vitro fertilization (IVF) has revolutionized the field of assisted reproductive technologies (ART) by offering hope to individuals and couples struggling with infertility. Nevertheless, traditional IVF methods are not exempt from drawbacks, such as suboptimal success rates, intrusive procedures, and ethical considerations. The introduction of micro/nanorobotics in IVF offers a revolutionary chance to tackle these difficulties. This paper presents a short review of the utilization of micro/nanorobotics in IVF, investigating progress in the manipulation of sperm, retrieval of oocytes, culture of embryos, and potential future developments in this fast progressing area. In this discussion, we explore the fundamental concepts, advantages, difficulties, and possible influence of micro/nanorobotics in transforming IVF processes and enhancing patient outcomes.

Engineering Education needs to be approached in different, innovative ways to meet the needs of society, learners, and education providers. This ranges from new educational programs and innovative pedagogies in individual classrooms, to online and immersive learning, to micro-credentials and modularity along with how to enable rapid adaptation for reskilling and upskilling, to entirely new pathways of restructuring education. Gamification is the application of game elements and digital game design techniques to non-game problems, such as learning challenges. It is about using game-based mechanics, aesthetics, and game thinking to enhance users’ engagement, motivate action, and support learning. At first view, the concept of gamification does not contain game design elements, but with the addition of additional elements such as the video game component that is applied in different contexts, the users are encouraged to participate in learning activities and complete learning challenges successfully. The first step in the process of designing a gamification activity is to think like a game designer. According to Cook (2013), any process can be gamified when the following requirements are covered: (i) the gamified activity is easy to learn, (ii) user progress can be measured, (iii) continuous feedback is provided to users.

Objective To observe the effect of roxadustat on blood pressure and micro-inflammatory response in patients with hemodialysis anemia, and to provide a viable technique for the treatment of hemodialysis anemia patients. Methods A total of 100 hemodialysis anemia patients admitted to the Nephrology Department of our hospital from July 2020 to July 2021 were enrolled and randomly divided into an observation group (roxadustat) and a control group (human recombinant erythropoietin (rhEPO). The clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure were recorded and compared. Results There was no significant difference in baseline data and serum indicators (P>0.05). The study group demonstrated superior performance to the control group in terms of clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure (all P<0.05). Conclusion Compared with rhEPO treatment, roxadustat exhibits a promising outcome in treating anemia and has slight impact on blood pressure of patients.

Micro-gyroscopes based on the Coriolis principle are widely employed in inertial navigation, motion control, and vibration analysis applications. This paper presents our main contributions which include a novel dual-frame optomechanical gyroscope, a unique photonic crystal cavity design, and advanced numerical simulation and optimization methods. The proposed design utilizes an optical cavity formed between dual oscillating frames, whereby input rotation induces a measurable phase shift via optomechanical coupling. Actuation of the frames is achieved electrostatically via an interdigitated comb-drive design. Through theoretical modeling based on cavity optomechanics and finite element simulation, the operating principle and performance parameters are evaluated in detail. Results indicate an expected angular rate sensitivity of 22.8 mV/°/s and angle random walk of 7.1×10-5 °/h1/2, representing superior precision than to existing micro-electromechanical systems gyroscopes of comparable scale. Detailed analysis of the optomechanical transduction mechanism suggests this dual-frame approach could enable angular vibration detection with resolution exceeding state-of-the-art solutions.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

Active transportation, such as walking, cycling, and micro-mobility modes, has received a lot of attention in recent years due to its potential benefits to urban residents, such as less traffic, better air quality, more opportunities to get exercise, and an overall higher quality of life. In this study, we used Classification and Regression Trees (CART) to compare and contrast three mobility options: shared micro-mobility, individual micro-mobility, and walking. We surveyed 219 people living in Budapest, Hungary, to learn more about their travel habits and investigate the demographic elements that influence people's mode choice, such as age, gender, ownership of micro-mobility modes, education, job, and income. Results showed that ownership of personal micro-mobility modes, and age as important predictors of active travel mode choice. Males seem to prioritize cost and weather conditions when choosing shared micromobility modes, while females value safety and weather conditions. Our findings can guide policy decisions and urban planning initiatives by identifying the most significant predictors of mode choice and evaluating the possible benefits and drawbacks of each mode.

This manuscript presents a study on the spatial relationships between bike accidents, the built environment, land use, and transportation network characteristics in Budapest, Hungary using Geographic Weighted Regression (GWR). The sample period included bike crash data between 2017 and 2022. The findings provide insights into the spatial distribution of bike crashes and their severity, which can be useful for designing targeted interventions to improve bike safety in Budapest and be useful for policymakers and city planners in developing effective strategies to reduce the severity of bike crashes in urban areas. The study reveals that the built environment features, such as traffic signals, road crossings, and bus stops, are positively correlated with the bike crashes index, particularly in the inner areas of the city. However, traffic signals have a negative correlation with the bike crash index in the suburbs, where they may contribute to making roads safer for cyclists. The study also shows that commercial activity and PT stops have a higher impact on bike crashes in the northern and western districts. The GWR analysis further suggests that one-way roads and higher speed limits are associated with more severe bike crashes, while green and recreational areas are generally safer for cyclists. Future research should be focused on the traffic volume and bikes trips’ effects on the severity index.

About 90% of the Ataulfo mango (Mangifera indica L.) crops in Mexico are in the south of the country. This variety has significant amounts of antioxidant compounds. All the trees come from a small group of parents, however, the possible intravarietal variations and the micro-environments where it is grown can influence the compounds that contribute to the antioxidant capacity. The objective of this study was to quantify the antioxidant compounds of Ataulfo mango fruits of trees grown in Soconusco, Chiapas, Mexico (origin denomination), as well as fruits of the parent trees. In addition, possible associations between the contents of these compounds and the micro-environmental conditions collected were sought. In total, 465 fruits from 155 trees planted in 13 municipalities (locations) were analyzed. Fruits were collected at physiological maturity and stored at 25 °C until reaching commercial maturity. The contents of total phenolic compounds (TPC), antioxidant capacity (AC by DPPH, ABTS and FRAP methods), total anthocyanins (TA) and ascorbic acid (AA) were determined. The fruits from Huehuetán, presented the highest contents of PC (0.89 mg GAE g-1); however, the highest AC was found in the fruits harvested in Frontera Hidalgo, with 128.29 µmol TE g-1 (ABTS). The fruits obtained from the parents are within the average range of total TPC and AC, without significant differences between their fruits and those cultivated. The micro-environments where the Ataulfo mango trees are grown do not have a significant effect on antioxidant compounds (TPC, AC, TA and AA) and the only variables that allow segregation by localities are relative humidity, environmental temperature and altitude.

Severe respiratory syncytial virus (RSV) infections in early life have been linked to the development of chronic airway disease. RSV is a potent inducer of reactive oxygen species (ROS) which contributes to inflammation and enhanced clinical disease. NF-E2-related factor 2 (Nrf2) is an evolutionary conserved redox-responsive protein that helps to protect cells and whole organisms from oxidative stress and injury. The role of Nrf2 in the context of viral-mediated chronic lung injury is not known. Herein, we show that RSV experimental infection of adult Nrf2 deficient BALB/c mice (Nrf2-/-; Nrf2 KO) is characterized by enhanced disease, increased inflammatory cell recruitment to the bronchoalveolar compartment, and a more robust upregulation of innate and inflammatory genes and proteins, compared to wild type Nrf2+/+ competent mice (WT). These events that occur at very early time points, lead to increased peak RSV replication in Nrf2 KO compared to WT mice (day 5). To evaluate longitudinal changes of the lung architecture, mice were scanned weekly by high-resolution micro-computed tomography (micro-CT) imaging up to 28 days after initial viral inoculation. Based on micro-CT qualitative 2D imaging and quantitative reconstructed histogram-based analysis of lung volume and density, we found that RSV infected Nrf2 KO mice developed significantly greater and prolonged fibrosis compared to WT mice. Results of this study underscore the critical role of Nrf2-mediated protection from oxidative injury not only in acute pathogenesis of RSV infection, but also in its long-term consequences of chronic airway injury.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dual-channel equalization, both based on high-Q integrated ring resonators. The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies. They operate via TE/TM mode birefringence in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

This paper presents a novel micro-segmented genetic algorithm (μsGA) to identify the best solution for the locomotion of a quadruped robot designed on a rectangular ABS plastic platform. We compare our algorithm with three similar algorithms found in the specialized literature: a standard genetic algorithm (GA), a micro-genetic algorithm (μGA), and a micro artificial immune system (μAIS). The quadruped robot prototype guarantees the same conditions for each test. The platform was developed using 3D printing for the structure and can accommodate the mechanisms, sensors, servomechanisms as actuators. It also has an internal battery and a multicore embedded system (mES) to process and control the robot locomotion. This research proposes a μsGA that segments the individual into specific bytes. μGA techniques are applied to each segment to reduce the processing time; the same benefits as the GA are obtained, while the use of a computer and the high computational resources characteristic of the GA are avoided. This is the reason why some research in robot locomotion is limited to simulation. The results show that the performance of μsGA is better than the three other algorithms (GA, μGA and AIS). The processing time was reduced using a mES architecture that enables parallel processing, meaning that the requirements for resources and memory were reduced. This research solves the problem of continuous locomotion of a quadruped robot, and gives a feasible solution with real performance parameters using a μsGA bio-micro algorithm and a mES architecture.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Various natural disasters such as floods, fires, earthquakes, etc. have affected human life. Detection and classification of large and small earthquakes caused by natural or abnormal events have been always important to Earth scientist. One of the most important research challenges in this field is the lack of an effective method for identifying and categorizing various types of seismic events at less important and important levels. Based on latest achievements of Data Mining international institutions such as Rexer-KDnugget-Gartner and also newest authentic articles, SVM, KNN, C4.5, MLP are from most important and popular and leading classifiers in data world.Therefor in present study, a boost learning system consisting support vector machine algorithms with linear regression, MLP Neural Network ، C4.5 decision tree and KNN near neighborhood have been utilized in a combined form to detect and categorize micro seismic events. In general, the steps involved in the proposed method are: 1) performing artificial seismic tests, 2) data gathering and analysis, 3) conducting preprocessing and separating training and testing samples, 4) generating relevant models with training samples and detecting and categorizing test samples and 5) extracting a cluster with the maximum candidate using boost learning. After simulations, it was observed that the accuracy of proposed boost method to the best answer was about 6.1% higher compare to other methods and the error rate was 0.082% of recalling. Accuracy of detection and classification to the best answer were also improved compare to other methods up to 2.31% and 6.34%, respectively.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

In recent years there has been a clear increase in bottled water consumption, globally which translates to significant health and environmental concerns. This cross-sectional study aims to understand the attitude and preferences of university students in Qatar towards use of bottled and tap water for drinking purposes using an online survey questionnaire. The number of students who responded to the online survey was 14% of the entire student population within the university (n = 688). Overall, majority of the students reported plastic bottled water as the main source of drinking water they preferred to use on campus (n=468; 68.02%), with a higher proportion of females (72.08%) preferring the use of plastic bottled water. Out of the 468 students who preferred plastic bottled water, safety was the most important factor (43.80%) followed by convenience (16.88%) and taste (15.60%). Cost (15.17%), personal/family habits (5.13%), Environmental concerns (2.14%) and minerals (1.28%) were found to be the least important factors. Among the 45 students who preferred tap water over plastic bottled water, cost (46.67%) was the dominant factor followed by convenience (20.00%) and environmental concerns and safety (13.33% each), taste (4.44%), and personal/family habits (2.22%). This study recommends campaigns to focus on attitude and behavior change and not solely emphasize knowledge; 71.7% believed that plastic water bottles are more harmful to the environment, yet the greater majority still resorted to this source. There is an immediate need to further educate students through environmental and health literacy programs on water consumption and quality. Enabling the population to understand the positive and negative aspects of their choices, may be an effective remedy to ensuring a healthy population and healthy environment.

Remote sensing methods have the potential to improve lake water quality monitoring and deci-sion-making in water management. This reviews introduces novel findings in the field of opti-cally active water quality parameters using remote sensing. It summarizes existing retrieval methods (analytical, semi-analytical, empirical, semi-empirical, and artificial intelli-gence/machine learning (AI/ML)), examines measurement methods used to determine concen-tration of specific water quality parameters, summarizes satellite systems that enable temporal data for understanding the state of the lake with focus on water quality parameters, and pro-poses enhancements for future research of lake water quality using remote sensing. As part of this review, eight optically active biological and physical water quality parameters were ana-lyzed, including chlorophyll-α (chl-α), transparency (Secchi disk depth (SDD)), colored dis-solved organic matters (CDOM), turbidity (TUR), electrical conductivity (EC), surface salinity (SS), total suspended matter (TSM), and water temperature (WT). The research proposes a shift from point-based data representation to a more reliable raster representation and encourages optimizing grid selection for in situ measurements by combining hydrodynamic model with re-mote sensing methods. This review presents a comprehensive summary of the bands, band combinations, and band equations per sensor for eight optically active water quality parameters as listed in Tables A1-A8. The review’s findings indicate that use of remotely sensed data is an effective method for estimating water quality parameters in lakes, with a significant increase in global utilization. The review highlights potential solutions and limitations to the challenges of remote sensing water quality determination in lakes.

A Water demand per capita will rise in the Arab world as a result of climate change and population expansion. One of the most important aims in coping with population increase around the world is to conserve water supplies. As a result, the Kingdom of Saudi Arabia constructed Al Wajeed Water Treatment System to meet the demands of the southern population. This research aims to assess the drinking water quality produced from the AlWajeed Water Treatment System. Monthly water samples were collected (January 2018 to January 2021) from the Al Wajeed Water Treatment Framework (4sites), extending to governorates; Bishah`s distribution system (5sites) and Tathleeth`s distribution system (7sites). Water quality criteria, such as physical, chemical, and microbiological parameters, revealed that the majority of water samples collected from the Al Wajeed Water Framework and its environs are of a good quality matched the national and international standards. Few sites showed water quality criteria, such turbidity, fluoride and total coliform did not comply with national and global standards. The obtained results explained the importance of monitoring and follow-up programs for drinking water criteria. In addition, they can help the authorities and stakeholders in the sustainable development.

The River Basin Management Plan (RBMP) is an essential component of the European Union Water Framework Directive that details an integrated approach required to protect, improve and sustainably manage water resources. RBMP were intended to be produced for the periods 2009-2015, 2016-2021 and 2022-2027. However, after two years of delays in the development processes, the Republic of Ireland produced its first RBMP in 2010. The second RBMP cycle was also implemented in 2018 and is expected to run until the end of 2021 to give way to the third RBMP, whose consultation processes have been ongoing since December 2019. This paper contributes to the forthcoming RBMP by assessing stakeholders’ perspectives on the second RBMP through a desk-based review and by conducting interviews with nine institutions (14 interviewees). The qualitatively analysed interviews reveal a broad spectrum of actors associated with water management and governance in the Republic of Ireland through a three-tier governance structure that has been delivered (with amendment) through the first two RBMPs. Organisations such as the An Fóram Uisce|The Water Forum, the Environmental Protection Agency, the Local Authority Waters, and the Agricultural Sustainability Support and Advisory Programme have responsibilities designated in the RBMPs to deliver improved water quality, integrated catchment management, community engagement and awareness-raising. Trust has also been building up among these organisations and other agencies in the water sector. Despite these responsibilities and progress, the interviews identified communication lapses, ineffective collaboration and coordination among stakeholders and late implementation to be hampering the successful delivery of the second RBMP, in addition to significant pressures acting on water bodies from agricultural activities and urban wastewater treatment. Towards the third RBMP, the paper concludes that optimised water sector finance, enhanced and well-resourced communications, and improved stakeholder collaboration are needed to foster effective and efficient water services delivery and quality. More so, given the cross-cutting impact of the Sustainable Development Goals on water resources and the interconnected relations among the goals, the paper further recommends the integration of the SDGs in the various plans of actions and a co-benefits approach to derive the triple benefits from biodiversity, climate change initiatives and water quality measures.

In response to droughts, various media campaigns and water saving instructions are released, often however, with only temporary water conservation effects. A promising development is this regard are Digital Water Meters (DWM) that provide near real-time water-use feedback. Despite extensive DWM experience in some water-stressed regions, a profound understanding of the initial attitude towards DWM and message tailoring opportunities are rarely empirically explored. Therefore, we aim to obtain insights into the attitude towards the introduction of DWM and explore opportunities for message tailoring, a topic of extra relevance as we may be on the threshold of a large-scale implementation in many world regions. Messages tailored to (i) normative beliefs and attitudes on drinking water, (ii) water-use activity and (iii) phase of decision-making, seem particularly compatible with DWM. Through a survey (n=1037) in the Netherlands, we observe that 93% of respondents have no objections utility investments in DWM and that 78% would accept a free DWM because of improved leakage detection, lower costs and environmental considerations. Finally, instead of sociodemographic factors, we observed that an attitude-based customer segmentation approach proved an especially useful predictor of respondent’s motivation to endorse DWM and forms a promising basis for water conservation message-tailoring strategies.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Rural areas are not only faced with the problems of rural depopulation but also with the problem of water supply and water quality which is a basic necessity of life. In light of this, this paper assesses the rural water supply situation and the bacteriological quality of different water sources in the Obokun Local Government Area of Osun State, Nigeria. The safety of the water sources for human consumption and possible occurrence of the water borne diseases in the study area were determined. The study employed descriptive and analytical methods of data analysis to achieve the objectives of the inquiry. Findings showed that the study area suffered from inadequate water supply and poor locations of the sources of water: The study also revealed that the microbiological quality of the water sources used was unsafe, poor and not acceptable for human consumption. In addition, many man- days-hours were wasted in search of water. It is therefore recommended that the government should make the rural water supply and the maintenance of water quality a priority in its policy formulation.

Water quality assessment stands as a fundamental step in water resource management. In addition to substances and organisms present in the water, land use and land cover are two factors affecting also water quality. This study analyzed the correlation and influence between water quality and land use and land cover in the Miranda River Basin (MRB) and the natural wetlands in the Pantanal Biome. Using a watershed-wide approach, results suggested that water quality management policies can be considered in terms of sub-basins (smaller planning units). The Water Quality Index (WQI) was considered GOOD or EXCELLENT throughout the MRB. It was observed that the natural wetlands have the capacity to contribute to improve WQI, with reductions in thermotolerant coliforms and turbidity; however, high values were found for thermotolerant coliforms, a temporal increasing trend of biochemical oxygen demand (BOD), and a reduction in dissolved oxygen and total phosphorus. Conversely, it was found in these flooded areas a trend of decrease in dissolved oxygen and an increase in BOD concentrations. Natural wetlands play important hydrological and ecological roles in water quality, storing, removing, and cycling nutrients. They are highly relevant areas for defining watershed management and conservation strategies, environmental protection, and providing ecosystem services.

High Education Institutions (HEI) play a key role in fostering sustainability since students will be future active society members. By providing them with the knowledge, skills, and mindset needed to address environmental challenges, they can contribute to increase sustainability in a long-term approach. With the effects of climate change strongly affecting water availability across planet, it is increasingly relevant to understand if higher education students are aware of this situation, to develop adequate measures to promote sustainable behaviors regarding water uses. This study aimed to assess students’ perceptions regarding water efficiency through a questionnaire submitted in 7 HEI in Portugal. Students recognized the importance of water with older students, women and science students demonstrating a greater awareness. Inspite of this 27% students do not know what the average water consumption in Portugal is and only 18% accurately reported the consumption range in Portugal. There is also a lack of knowledge (&gt;50% students) if common water efficiency measures are applied in their HEI. The main information sources identified by the students were “social communication” and “internet/social media”, revealing that water efficiency knowledge transfer in high education can be improved.

: This study examines the prospects of residential water demand management policy regulations in Ethiopia and their implications for sustainable water resource management. This study aims to evaluate the existing policy regulations and analyze their effectiveness in promoting efficient water use and conservation practices in residential areas. By considering the potential challenges and opportunities associated with these regulations, the research provides insights into the future of residential water demand management in Ethiopia and suggests strategies for enhancing sustainable water resource management. Integrated literature and policy document review, alongside observation and interviews, was used to assess the viability of residential water demand management policies. The assessment of current policy regulations for residential water demand management in Ethiopian urban towns has revealed significant shortcomings in promoting water conservation activities. Hence, there is a need for significant improvements in the current water resource policy guidelines, which lack specificity, particularly in residential water demand management conservation strategies. The lack of awareness among residents regarding the importance of conserving their limited water resources is evident. To address these challenges and ensure the sustainability of the water supply, the government and policy developers must engage with various stakeholders, including the community, in the process of revising current policy documents. A more precise and tailored approach is necessary for its effective implementation.

Turkiye, located in the Mediterranean Basin, has started to experience the impacts of climate change, primarily manifesting in severe droughts that significantly affect agricultural output. Water stands as a crucial component in agricultural production. This study aims to propose water efficiency measures essential for climate change adaptation. By accessing pertinent data, partic-ularly in agriculturally reliant developing nations, this research endeavours to analyse yield losses in major crops within agricultural regions using the most suitable methodologies. Furthermore, it seeks to ascertain the financial ramifications of such losses. The methodological framework de-vised for this purpose was implemented in Türkiye's Iğdır Plain, selected as the study site. In 2022, the Iğdır province received 40% less precipitation than its usual levels. This study anticipates substantial losses in agricultural yield due to water scarcity resulting from prolonged drought conditions. Analysis reveals that among the crops cultivated in the region, clover belonging to the field crops category exhibits the highest water dependency, while apricot demonstrates the least reliance on water resources. In light of these considerations, the recommended crop rotation for the Iğdır Plain under water constraints comprises wheat, watermelon, maize, melon, apple, and apricot. Emphasizing enhanced water transmission and utilization efficiency, particularly in ir-rigation zones, prioritizing water stress-resistant crops within basin crop patterns, and favouring alternative crops over those demanding excessive water will foster sustainable water resource management. This approach encourages farmers to actively engage in the adaptation process to climate change and drought conditions while minimizing the agricultural sector's vulnerability to the impacts of climate change, which heavily relies on water consumption

The sustainable management of water scarcity is a global crucial issue. Germany has es- tablished efficient water management systems, but the agricultural sector still struggles with water scarcity as the demand surpasses the available water supply. The primary aim is to establish a framework for making water accessible for irrigation and additional use on households through the effective utilization of recycled water from wastewater treatment facilities. The research inquiries are focused on evaluating the changes in the agricultural irrigation model in CROPWAT, determining the spatial distribution of zonal severity, estimating the capacity of urban roof catchments, and evaluating the reduction volume of efficient water required from the existing wastewater treatment plant supply. According to the findings, the annual amount of water required for agriculture in the designated study location is approximately 2.9 million m3. Although there is no initial need for irrigation water, yet the demand for irrigation water increases during the development, active growth, and mature stages of maize, winter wheat, and wine grapes, reaching around 189mm, 225mm, and 62mm, respectively. According to our observation, the annual water supply in Weinstadt is around 4 million m3. On the other hand, the amount of water calculated from urban roof rainfall is estimated 0.8 million m3, which is considered valuable from an economic standpoint. This economically efficient volume of water would reduce the current treated water supply passes an opportunity for enhanced agricultural irrigation

Pompeii was connected to the great Serino aqueduct under the principate of Augustus. From that moment on, water became not only a precious resource for the inhabitants but also their true social indicator. It is no coincidence, in fact, that the concentration of sumptuous dwellings is in Regio VI, the district closest to the aqueduct reservoir (castellum aquae in Latin) and the one most equipped with piezometric towers, the first of the network, the ones that would never leave the decorative fountains of the peristyles dry. From this observation follows the original possibility of considering the water network a factor that contributed to designating the morphology of urban neighbourhoods and blocks.

Yemen is a water-scarce country with inadequate fresh water and considerable groundwater depletion, as well as a lack of adequate surface water. The study region is considered an arid region, and there is insufficient water to meet the needs of the region's yearly population growth rate of 4 %. This study aims to assess the water resources in the Sana'a region and to identify the current water situation and forecast for the future. Rainfall changes spatial and temporal in very few quantities and an annual average of 267 mm. Water harvesting facilities are entirely filled by 75% of the total water facilities in the rainy seasons. The groundwater level in Sana’a Basin decreases about 6-8 meters annually due to the increase in the number of wells, the abundance of abstraction, and the lack of recharge. The amount of abstraction exceeds 400% of the recharge in the Sana'a basin. The water per capita is 70 - 85 m³ annually. It is an abstraction from the aquifers by private wells. The crop cultivated area decreased from 184217 hectares in 2007 to 122583 hectares in 2018 due to lack of water. The sewage treatment plant treats 18.25 Mm³ annually, with less than 70 % efficiency. The water deficit is about 500 to 723 Mm³ annually; it is an abstraction from the aquifers by private wells. The current water situation in the Sana'a region is catastrophic, and the planning and management must ensure a water balance in the future.

Hotel water systems colonized with Legionella spp. have been the source of travel-associated Legionnaires’ disease and cases, clusters or outbreaks continue to be reported worldwide each year. A total of 132 hotels linked with travel-associated Legionnaires’ disease, as reported through the European Legionnaires’ Disease Surveillance Network, were inspected and tested for Legionella spp. during 2000–2019 by the public health authorities of the island of Crete (Greece). A total of 3,311 samples were collected: 1,885 (56.93%) from cold water supply systems, 1,387 (41.89%) from hot water supply systems, 37 (1.12%) were swab samples and two (0.06%) were soil. Of those, 685 (20.69%), were collected from 83 (62.89%) hotels, testing positive (≥ 50CFU/L) for Legionella pneumophila) serogroups 1-10, 12-14 and non-pneumophila species (L. anisa, L. erythra, L. tusconensis, L. taurinensis, L. birminghamensis, L. rubrilucens, L. londiniesis, L. oakridgensis, L. santicrusis, L. brunensis, L. maceacherii). The most frequently isolated L. pneumophila serogroups were 1 (27.92%) and 3 (17.08%). Significantly higher isolation rates were obtained from hot water supply systems (25.96%) versus cold water systems (16.98%) and swab samples (13.51%). A Relative Risk (R.R.) > 1 (p < 0.0001) was calculated for hot water temperature <55 °C (R.R.: 4.43), chlorine concentrations <0.2 mg/L (R.R.: 2.69), star rating <4 (R.R.: 1.73) and absence of Water Safety Plan implementation (R.R.: 1.57).

Tanzania with 945 million hectares of land area and annual rainfall of 300 mm on 67% of its territorial land is considered as a semi-dry region in the world. Rice production in Tanzania needs to be increased to feed a growing population, whereas water for irrigation is getting scarce. One way to decrease water consumption in paddy fields is to change the irrigation regime for rice production and to replace continuous flooding with alternate wetting and drying. In order to investigate the effect of different regimes of irrigation and nitrogen fertilizer on yield and water productivity of hybrid rice, two greenhouse pot experiments comprising soils from upland and lowland production ecologies were conducted at Sokoine University of Agriculture, Tanzania during crop seasons of 2019. The experiment was arranged in split plots based on randomized completely block design with 3 replications. Water regimes were the main factor comparing continuous flooding (CF) and alternate wetting and drying (AWD) with nitrogen fertilizer levels as the sub-factor including absolute control , 0, 60, 90, 120 and 150 kg/ha. Alternate wetting and drying (AWD) improved water productivity in both upland and lowland production ecologies compared to CF. AWD increased yield under lowland production by 13.3% while in upland there was 18.5% decrease in yield. The average water use varied from 31.5 to 84 L pot-1 under upland trials, while in lowland trials it was 36 to 82.3 L. Higher yield and lower water application led to an increase in WP varying from 1.2 to 1.8 kg cm-3 under upland trials, and 0.6 to 1.5 kg cm-3 under lowland trials. The variation in water productivity among treatments was mainly due to the differences in the yield, water and nitrogen levels used in the production process. Both sets of trials recorded water saving up to 34.3% and 17.3% under lowland and upland trials, respectively. Under upland trials, the yield varied from 39.9 to 124.1 g pot-1 and in lowland trials yield ranged from 20.6 to 118.2 g pot-1 representing paddy rice. The measurements showed that less water can be used to produce more crops under alternative rice growing practices. The results are important for water-scarce areas, providing useful information to policy makers, farmers, agricultural departments, and water management boards in devising future climate-smart adaptation and mitigation strategies.

The key goal of the current study was to determine suitable areas of water pumping for drinking and agricultural harvest in Tabriz aquifer, located in East Azerbaijan province, northwest Iran. In the study area, groundwater is the key foundation of water for drinking and farming requirements. Groundwater compatibility study was conducted by analyzing Electrical conductivity (EC), Total dissolved solids (TDS), Chloride (Cl), Calcium (Ca), Magnesium (Mg), Sodium (Na), Potassium (K), Sulfate (SO4), Total hardness (TH), Bicarbonate (HCO3), pH, carbonate (CO3) and Sodium Adsorption Ratio (SAR) obtained from 39 wells in the period of 2003 to 2014. For this purpose, the Water Quality Index (WQI) and irrigation water quality (IWQ) index were utilized. The WQI index zoning exposed that the groundwater of the study area for drinking purposes is categorized as excellent, good and poor water. Most drinking water harvested for urban and rural areas are in the class of 'excellent water'. The results revealed that about 37 percent (296 km2) of groundwater has high compatibility, and 63 percent of the study area (495 km2) has average compatibility for agricultural purposes. The trend of IWQ and WQI indexes demonstrates that the groundwater is getting worse over the time.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

The Brazilian water legislation advocates that some uses have priority over others, but this aspect has never been clearly addressed, generating conflicts. Water authorities usually refer to hydrological models to justify their decisions on water allocation. However, a significant group of stakeholders does not feel qualified to discuss these models and is, therefore, excluded from the decision process. We hereby propose a hydrologically robust method to correlate water uses with their respective reservoir alert volumes, which should empower the less formally educated stakeholders. The method consists of: (i) generating the water discharge versus reliability curve, using a stochastic approach; (ii) generating the withdrawal discharge versus alert volume family of curves, using a water-balance approach; (iii) calibrating the key parameter T using field data; and (iv) associating each water use with its alert volume. We have applied the method to four of the largest reservoirs (2.10³ - 2.10² hm³) in the semi-arid Ceará State. The results indicate that low-priority water uses should be rationalized when the reservoir volume is below 20%; whereas uses with very high priority should start rationalization when it is below 11%. These hydrological guidelines should help enhance water governance among non-specialist stakeholders in water-scarce and reservoir-dependent regions.

Lack of water resources in Iran, especially in recent years, has faced the agricultural sector as the most important consumer of water resources, with serious challenges. In Iran, the agricultural sector accounted for more than 90% of water consumption. However, the focus on domestic production and self-sufficiency policy in staples (wheat, barley, maize and rice) has been emphasized in general agriculture's policy. This study was conducted to estimate the imported virtual water from the imports of basic products in Iran using defined indicators during 1961-2013. Also this study investigated the possibility of achieving self-sufficiency due to the limited water resources in Iran. The results of this study showed with the increase in cereal imports, virtual water imports from 0.28 billion cubic meters in 1961 increased to 17.6 billion cubic meters in 2013 and on average about 60% of virtual water imports in strategic products is related to wheat imports during the past 53 years. Other products in cereal (barley, maize and rice) are also indicative of the general trend of increasing imports of virtual water in development plans. The estimated long-run elasticity of virtual water imports in the cereal group compared with the country's water resources also showed that with a one percent reduction in renewable water resources of the country, the virtual water import in the main cereal group will increase equivalent to 2.89 percent and the determination coefficient more than 90 percent also confirms this negative relationship. According to this result and the emphasis on the fact that renewable water resources per capita in the country is falling increasingly, it cannot be expected that domestic production could compensate for the imports of the cereal group and virtual water imports with current technology, without increasing the water productivity and without additional harm to water resources.

Cross-border e-commerce is an opportunity for micro, small and medium sized enterprise (MSMEs) in developing countries. Based on a resource-based approach, this research studied how to support resource lacking enterprises with export marketing strategy. It dealt with actual business cases of Mongolian entrepreneurs trying to export Mongolian products to Korean market. Multiple source data including interviews, internal documents, and group discussions, were matched with theories to come up with strategies and validated by supporting organizations in Mongolia and Korea. The research suggests that MSMEs should rely on third party digital platforms rather than setting up their own. For product strtategy of the marketing mix, sellecting competitive product categories and supporting them adjusting to foreign markets and quality assurance is needed. For price strategy, loccally high priced products should use a price penetration strategy with a lower price compared to competing foreign products. For place strategy, supporting organizations should partner with exporters for collective delivery. For promotion strategy, they need to support the capacity of MSMEs enabling them to use digital marketing tools effectivly. These strategies were validated and adopted by supporting organizations in Monglia and Korea.

In times of water scarcity, water conservation measures from authorities are primarily directed to the residential sector—homeowners and renters who engage in individual activities to reduce water consumption. Business owners, manufacturers, and institutional workers—the ICI sector, generally, do not receive targeted information and education on water savings measures, and when they do, the information, typically, refers to indoor technologies, and behavior choice. In answer to this shortfall, this research illustrates how the ICI sector might engage in outdoor water conservation and, thus, realize water savings using the well-established Pittenger’s Simplified Landscape Irrigation Design Estimation (SLIDE) formula that estimates outdoor water conservation/savings for the lesser studied industrial, commercial, and institutional (ICI) sector. We applied the SLIDE formula five diverse climate areas in Texas to demonstrate the potential water savings in each, as well as identifying the type of water technology measures that yielded the greatest water savings for outdoor ICI landscapes. Overall, the greatest water savings for outdoor ICI landscapes was realized through smartscape design with soil moisture sensors-SMS technology, second best. Our findings will provide ICI facility owners/managers with knowledge and examples of a simplified system for quantitative decision making when considering choices among technologies and/or practices toward outdoor water conservation for their own facilities.

The number of disputes related to water that reach courts in Chile has increased in the last decades, the topics of these disputes have become more complex, and the current conflict resolution system has not been able to adjust to this situation. This study analyses colonial texts from water-related conflicts that were addressed at the Royal Hearings in Santiago (1691-1800) and from the Cabildo gatherings (1541-1802), using an adaptation of the Institutional Analysis and Development framework. The research shows a strong institutional system surrounding conflict resolution during colonial times, with nested schemes and empowered figures appointed in leading roles. However, a lack of equity and inclusion of all actors is also visible, reducing its legitimacy. At present, the increasing value of water and a sense of distrust in the institutional system have led to longer and more complex conflict resolution processes. Here, learning from past times about the empowerment of the institutional system for solving water disputes could be useful. An increased support towards initial conflict resolution mechanisms, giving space for local knowledge and generating stronger participation in these initial steps, could also be a lesson for the future.

Many techniques have been and are being made to find alternatives to water-saving practices. Among them, Partial root drying (PRD), one of the effective approaches, plays a major role in reducing the harmful effects of water deficit stress. An experiment was carried out using irrigation strategies [I1 (100% full irrigation “FI”), I2 (75%FI), I3 (50%FI), and I4 (PRD (50%FI)] and soil organic mulch [L0 (Zero layer organic soil mulch” control”), L1 (Single layer organic soil mulch), L2 (Two layers of organic soil mulch), and L3 (Three layers of organic soil mulch)] to inspect the impact of those treatments for increasing yield, water productivity and saving energy under arid region conditions. To meet the study's objective, two field experiments were carried out at a private farm. Our results demonstrated a general decrease in water stress and salt accumulation inside root-zone area with PRD with L3. The PRD strategy increased fruit yields by 3.7 and 7.3% and water productivity by 51.9 and 53.1% compared with I1 during 2020/2021 and 2021/2022, respectively, while reducing the applied irrigation water by 50 %. The PRD strategy showed superior results in increasing mango yield and water productivity. In general, PRD can be used as good technique to save water and energy up to 50% and enhance productivity along with using organic mulching, ultimately improving mango yield under arid climatic regions. It may prove a good adaptation strategy for current and future water shortage scenarios of climate change.

Although the water absorption feature (WAF) at 970 nm is not very well-defined, it may be used alongside other indices to estimate the canopy water content. The individual performance of a number of existing vegetation water content (VWC) indices against the WAF is assessed using linear regression model. We developed a new Combined Vegetation Water Index (CVWI) by merging indices to boost the weak absorption feature. CVWI showed a promise in assessing the vegetation water status derived from the 970 nm absorption wavelength. CVWI was able to differentiate two groups of dataset when regressed against the absorption feature. CVWI could be seen as an easy and robust method for vegetation water content studies using hyperspectral field data.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Road traffic transportation has flourished in the process of urbanization by its advantages, but it also produces harmful environmental vibrations. The vibration problem is especially significant for production workshops with precision instruments. A field measurement was conducted to analyze the source characteristics and propagation laws of traffic-induced vibrations. Off the northern side of an urban highway lies a microelectronics workshop. When a large truck passes by, both the vibration responses on the ground and in the workshop considerably increase. Greater vibration is produced in the vertical direction than in the X and Y axes. The predominant frequency band of the vibration response caused by road traffic vehicles is lower than 20 Hz. The vertical vibration responses of the first and second floors in the workshop greatly exceed the VC-C limit because of the high daily traffic flow. Attribute to the excitation of the operation of the manufacturing equipment on the second floor, the vertical vibration level of the second floor is essentially higher than that of the first floor. Therefore, it is impossible to disregard the micro-vibration in the workplace produced by the manufacturing machinery as well as the ex-citement of the road traffic. The measured data can be used to test potential numerical models for forecasting vibrations caused by traffic on roads as well as to guide vibration assessment work throughout the planning and design stages of roads.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

The genus Eucalyptus is a globally captivated source of hardwood and is well known for its medicinal uses. The hybrid and wild species of Eucalyptus are widely used as exotic plantations due to their renowned potential of adapting to various systems and sites, furthermore, making the species the most extensively propagated. Despite unquestionable progression in biotechnological and tissue culture approaches, the productivity of plantations is still limited often due to the low efficiency of clonal propagation from cuttings. The obtained F1 hybrids yield high biomass and High-quality low-cost raw material for large-scale production, however, the development of hybrid, clonal multiplication, proliferation, and post-developmental studies are still major concerns. This riveting review describes the problems concerned with in-vitro and clonal propagation of Eucalypt plantation; recent advances in biotechnological and tissue culture practices for massive and rapid micro-propagation of Eucalyptus; as well, highlights the Eucalypt germplasm preservation techniques.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The purpose of this review is to present the current role of ultrasound-based techniques in the diagnostic pathway of prostate cancer (PCa). With overdiagnosis and overtreatment of a clinically insignificant PCa over the past years, multiparametric magnetic resonance imaging (mpMRI) became recommended for every patient suspected of PCa before performing a biopsy. It enabled targeted sampling of the suspicious prostate regions, improving the accuracy of the traditional systematic biopsy. However, mpMRI is associated with high costs, relatively low availability, long and separate procedure or exposure to the contrast agent. The novel ultrasound modalities such as shear wave elastography (SWE), contrast-enhanced ultrasound (CEUS) or high frequency micro-ultrasound (MicroUS) may be capable of maintaining the performance of mpMRI without its limitations. Moreover, the real-time lesion visualization during biopsy would significantly simplify the diagnostic process. Another value of these new techniques is the ability to enhance the performance of mpMRI by creating the image fusion of multiple modalities. Such models might be further analyzed by artificial intelligence to mark the regions of interest for investigators and help to decide about the biopsy indications. The dynamic development and promising results of new ultrasound-based techniques should encourage researchers to thoroughly study their utilization in prostate imaging.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

Despite much published literature on the impacts of agriculture on water quality, knowledge gaps persist regarding which farming systems are of most concern for these relationships, which could help water resource planners better target water management efforts. This study addresses these subjects, seeking to understand how this relationship varies across different farming systems. We used data on water quality status in watersheds of an agricultural region in southern Portugal and crossed it with a map of farming systems for the same region provided by a previous study. By overlaying both data layers, we characterized the areal shares of the farming systems in the watersheds and inspected how these shares relate with water quality status through logistic regression. Results support that the impact of agriculture on water quality is mostly related with specific farming systems. We believe this type of information can be of high interest for agricultural planners and policymakers interested in meeting water quality standards, and we conclude by suggesting innovative policy options based on payments to farmers operating selected farming systems, as a cost-effective way to reconcile agricultural and environmental policy objectives.

Japanese plums form part of a multi-billion rand deciduous fruit industry in South Africa. Despite this, there is a paucity of knowledge on the seasonal water requirements of plum orchards. In a time of changing climatic conditions and diminishing water resources, this gap in literature poses an imminent threat to the long-term sustainability and global competitiveness of the South African plum industry. Therefore, this paper aimed to provide a review of the available literature on the crop water requirements of full-bearing well-irrigated Japanese plum orchards for improved agricultural water management. Full-year water requirements for well-watered full-bearing Japanese orchards ranged between 921 and 1 211 mm a-1 with a mean value of 1 084 ±140 mm a-1. Canopy growth and pruning appeared to be the most common causes of differences in water requirement estimates. Growing season length also plays a role with late-season maturing orchards having higher water requirements than their early and mid-maturing counterparts. The knowledge review provided benchmark figures for the annual water requirements of Japanese plums. However further research is required to determine the water requirement of plums from planting to full-bearing age and the response of plum trees to water stress, in a South African context.

Despite the popularity of infant swimming programs, no evidence exists to determine whether they influence infants’ judgements and behavior when confronted with bodies of water. In the current study we examined whether the total number of swimming sessions an infant had participated in predicted whether they avoided a body of water they could enter via an edge (n = 101 infants) or a slope (n = 77 infants). An initial regression analysis revealed no association between the number of sessions and avoidance of the water via either type of entry. However, a secondary analysis of infants who had participated in fewer or more than 10 sessions revealed a significant interaction between number of sessions and type of entry into the water. Infants who participated in more than 10 sessions were more likely to avoid the water if they could access it via an edge but significantly more likely to enter the water if they could access it via a slope. Because we tested the two groups of infants in different countries, further research is warranted to determine if cultural differences in child rearing practices or variations in the content and/or teaching of the swimming programs might explain these intriguing findings.

This review evaluates the trajectory and sustainability of the global and Mexican aquaculture industry. Globally, the sector is experiencing rapid growth, catalyzed by evolving consumption patterns and technological advancements. Notwithstanding the benefits, environmental concerns necessitate an urgent shift towards sustainable practices. The focus then narrows to Mexico's aquaculture, tracing its history from the late 19th century. With an emphasis on species diversification, the country's sector demonstrates resilience and potential, with an impressive yield of 249,613.71 tons in 2021 despite regional consolidation. However, persistent challenges such as technological limitations, funding shortages, and access to quality seeds hinder progress. Risks, including disease outbreaks, negative environmental impact, economic volatility, regulatory compliance, and climate change, further underscore the need for sustainable strategies. With government support and unique geographical and climatic advantages, Mexico shows promise for a significant % growth projection of 25% over the next five years. This review underscores the importance of embracing technological innovation, implementing sustainable practices, and enacting supportive legislation for the long-term success of the aquaculture sector worldwide, with a particular focus on Mexico.

A model is proposed that describes the transfer of ions and the process of water dissociation in a system with a bipolar membrane and adjacent diffusion layers. The model considers the transfer of four types of ions: the cation and anion of salt and the products of water dissociation – hydrogen and hydroxyl ions. To describe the process of water dissociation, a model for accelerating the dissociation reaction with the participation of ionogenic groups of the membrane is adopted. The boundary value problem is solved numerically using COMSOL® Multiphysics 5.5 software. An analysis of the results of a numerical experiment shows that, at least in a symmetric electromembrane system, there is a kinetic limitation of the water dissociation process, apparently associated with the occurrence of water recombination reaction at the of the bipolar region. An interpretation of the entropy factor (β) is given as a characteristic length which shows the possibility of an ion that appeared as a result of the water dissociation reaction to be removed from the reaction zone without participating in recombination reactions.

High quantities of wastewater produced from producing natural gas and oil from the aquifer, which called produced water. The produced water was comprised of dissolved solids, suspended solids, emulsified oil, and organic and inorganic compounds. That should be treated it's before disposal because it causes harm to the environment. This study takes the produced water from the southern Iraqi oilfield drilling company to adsorption by the Cane papyrus as natural and low-cost adsorbent. The analysis completed by using Fourier transforms infrared spectroscopy, EDX spectra and Scanning Electron Microscopic (SEM) for Cane papyrus. Investigating the effect of many parameters such as adsorbent dosage, temperature, solution pH, mixer speed and contact time. The Langmuir, Freundlich, Temkin and Harkins-Henderson isotherm models were tested, the results were 0.998,0.966, 0.931 and 0.966 respectively. The Langmuir model was more suitable described the adsorption process than the other models. The kinetics results were, 0.984 for Pseudo-first-order, 0.938 for Pseudo-second order is, 0.979 for Intra particle diffusion study and 0.912 for the Elovich model, the Pseudo-first-order kinetic equation best described the kinetics of the reaction. The thermodynamics study effect temperature changes on the thermodynamic parameters such as standard free energy change (∆G°), standard enthalpy change (∆H°) and standard entropy change (∆S°). The experimental data obtained demonstrated that Cane papyrus is a suitable adsorbent for removing oil from produced water.

The paper presents a model of moisture transport in wood taking into account diffusion and the accompanying adsorption of water vapour through the skeleton. A two-parameter form of the source term was proposed, depending on the distance of the current mass concentration of bound water from the equilibrium state. The tests on cubic samples with a side of 2 cm were carried out which allowed to determine the coefficients of the proposed model on the basis of the reverse method. The tests were performed for pine, larch, oak and ash in all directions of orthotropy. Also the tests on thin samples were performed to verify the source term.

Effective water resources management requires assessments of water availability within a framework of complex institutions and infrastructure employed to manage extremely variable stream flow shared by numerous often competing water users and diverse types of use. The Water Rights Analysis Package (WRAP) modeling system is fundamental to water allocation and planning in the state of Texas in the United States. Integration of environmental flow standards into both the modeling system and comprehensive statewide water management is a high priority for continuing research and development. The public domain WRAP software and documentation are generalized for application any place in the world. Lessons learned in developing and implementing the modeling system in Texas are relevant worldwide. The modeling system combines: (1) detailed simulation of water right systems, interstate compacts, international treaties, federal/state/local agreements, and operations of storage and conveyance facilities; (2) simulation of river system hydrology; and (3) statistical frequency and reliability analyses. The continually evolving modeling system has been implemented in Texas by a water management community that includes the state legislature, planning and regulatory agencies, river authorities, water districts, cities, industries, engineering consulting firms, and university researchers. The shared modeling system contributes significantly to integration of water allocation, planning, system operations, and research.

To address the question whether there is evidence that drinking water in general or mineral water in particular is effective in preventing diabetes; we performed a literature search of randomized controlled trials (PubMed). The search resulted in very few trials (N = 9) investigating this topic: one trial investigates the effect of increasing water consumption on glycemic control in diabetic patients; two trials investigate the effect of drinking water with a meal in diabetic patients; while six trials compare the effect of mineral rich water with that of low mineralized water on glucose metabolism in healthy subjects. There is evidence that increasing water consumption can improve glucose metabolism and randomized controlled trials with mineral water suggest that waters containing relevant amounts of magnesium can exert an additional effect. The role of bicarbonate; which is present in all the mineral waters used in the trials; will be discussed. Future research needs to investigate the effect of mineral water in prediabetic individuals or individuals with impaired glycemic control.

The goods and services produced by forest and vegetation ecology system is the power by which human society can be promoted fast in high-quality and sustainable way. With the increase of population and economic development in water-limited regions, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services. To meet the demands of this situation, most of the original forest has changed into farmland, non-native forest and grass land. As a result, water-plant relationship changed from equilibrium to non-equilibrium, which led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the questions and realize the sustainable utilization of soil water resources and the high quality and sustainable development of social economy, it is necessary to apply the utilization limit theory of soil water resources by plants and the theory of soil water carrying capacity for vegetation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit of vegetation and serve high-quality and sustainable development.

Abstract: Urban population growth and the expansion of the built environment, pollution, overexploitation of water, inequality in water distribution, and the impacts of climate change in future availability of water, are all elements that jeopardize urban water security. Due to the complexity of urban water systems and their relevance for urban life, a holistic and integrative perspective is therefore needed to address such challenges. In this paper, Urban Water Metabolism (UWM) has been used for comprehensively understanding water (in)security in the City of Puebla (Mexico) and its metropolitan area. Water inflows and outflows have been estimated using a Material Flow Analysis (MFA) method with data either obtained from official sources or simulated with the Monte Carlo method. Our findings show that the UWM configuration in the City of Puebla and its metropolitan area is effective for generating profits to service providers and water related business, yet ineffective to guarantee citizens’ Human Right to Water and Sanitation (HRWS), a right recognized in the Constitution of Mexico. We conclude that to advance towards an inclusive and sustainable provision of water, economic interests must be reconsidered and therefore adjusted so they can be in line with such aspirational socioecological goals. UWM accounting can therefore inform new water governance arrangements, those based on both the best available knowledge and a vibrant participation of all relevant stakeholders.

Ad- and desorption forces move water in living xylem/wood from the root to the leaf thermodynamically. The doctrine of plant water transport, the so-called cohesion- or cohesion-tension theory, postulates however that the process is physically based on a hydraulic fluid flow with negative pressure in water conducting tubes originating from the leaves. Lower pressure (suction) driven volume flow is physically a branch of mechanics. Moisture absorbed from the soil via the root is thought to be pulled up the stem by the leaves in continuous and tensioned threads of water. It is assumed that the hydraulic Hagen/Poiseuille flow law, derived for tubes, applies in the xylem. In a textbook of botany you can find the opinion: "Just as the pipes of a water pipe supply necessary water to each household, leaf nerves supply water and nutrient salts to each individual cell.” (Translated from German). Many plant physiologists consider this hydraulic principle to be correct, but it does not remain unchallenged. Doubts are repeatedly expressed. The question arises: How does water transport actually take place? It is shown how the diffusive/adsorption transport principle works. The partial dehydration (desorption) of the plant, driven by the diffusive process of transpiration, forms a combined concentration and adsorption-site gradient for water in the xylem matrix. Especially with open stomata the lowest moisture concentration and the highest number of adsorption-sites for water (sites with free van der Waals forces), can be found in the mesophyll cell walls at the liquid/vapor boundary in the leaf. The water taken up by the root moves spontaneously in the direction of this boundary and can thus partially or completely compensate for the existing concentration- and adsorption-site- differences for water. Thus, a thermodynamic overlapping diffusive/adsorptive movement of moisture along the stationary xylem/wood takes place. After the introduction and a review of some controversies with cohesion theory, the physiology of the processes associated with long-distance water displacement is mentioned below. A thermodynamic adsorption hypothesis of the natural water transport in plants, based on known facts, is presented.