In this research, first a binary nanocomposite of magnetic recyclable photocatalyst Fe₃O₄/TiO₂, was synthesized by sol gel technique. Then, in order to enhance the photocatalytic activity of the synthesized nanocomposite, it was deposited by silver nanoparticles for using in degradation of organic pollutants 2, 4-dichlorophenol (2, 4-DCP) under visible light. A range of analytical techniques including XRD, FESEM/EDX, DRS, VSM and N₂ physisorption were employed to reveal the crystal structure, morphology and property of the nanocomposites. We obtained 32% and 55% degradation of 2, 4-DCP under visible light after 180 min irradiation in the presence of Fe₃O₄/TiO₂ and Fe₃O₄/TiO₂/Ag respectively. Thus, the excellent visible light photocatalytic activity of Fe₃O₄/TiO₂/Ag sample can be attributed to the surface plasmon resonance effect of Ag nanoparticles deposited on Fe₃O₄/TiO₂ nanocomposite.

In this work, TiO₂ QDs modifed NiO nanosheets was employed to imporve the room-temperature NO₂ sensing properties of NiO. The gas-sensing studies showed that the response of nanocomposites with the optimal ratio to 60 ppm NO₂ was nearly 10 times larger than that of bare NiO, exhibiting potential application in gas-sensing. Considering the commonly reported immature mechanism that the effective charge transfer between two phases contribute to enhanced sensitivity, QDs sensitization mechanism was further detailed by designing a seirs of contrast experiments. First, the important role of QDs size effect was revealed by comparing a little enhanced sensitivity of TiO₂ particle-modified NiO with largely enhanced senstivity of TiO₂ QDs-NiO. Second, and more important, the direct evidence of heterointerface charge transfer efficiency was detailed by extracted interface bond (Ti-O-Ni) using XPS peak fitting. We hope this work can provide guideline to design more QDs-modified nanocomposites with the higher sensitivty for practical application.

This research was presented the special designed microfluidic device generated for sperm separation based on assumption of different surface electrical charged of sperms X and Y. However, to avoid ethical problem, the microfluidic chip has been tested with the mimic electrical charged particles, TiO₂-coated Polystyrene beads, (TiO₂-coated Ps-beads), instead of spermatozoa. The work has been separated into three main parts. Firstly, the simply but efficient fabrication of negatively charged TiO₂-coated Ps-beads has been presented. In addition, various characterization techniques such as X-ray diffraction (XRD), Tungsten Scanning Electron Microscopy (W-SEM) with energy-dispersive X-ray spectroscopy (EDS) mode, and X-ray Absorption Spectroscopy (XAS), have been reported in this work to elucidate the reasons behind the persistence of negatively charged on the surface of TiO₂-coated Ps-beads. Results show that the fabricated TiO₂-coated Ps-beads was partly coated in the mixed forms of amorphous Ti⁴⁺ and had caused a negatively charge to appear on the surface after fabrication and had sustained its electrical charged for long. Secondly, process of simulation and fabrication of microfluidic device was presented. Finally the negatively charged TiO₂-coated Ps-beads were tested in this microfluidic devices. For design of microfluidic devices integrated with a couple of microelectrodes, the simulated structures were fabricated by photolithographic technique and tested with the Ps-beads. Percentage of validation for Ps-beads separation indicated that the 100 mm-distance-between-electrodes microfluidic device exhibits to be the highest performance prototype at 86.96%. For further confirmation, another model so called the single path prototype has been established. It is confirmed by 92.59% of validation for the utilization of the device. The successfully designed microfluidic devices can be examined with actual spermatozoa later. Furthermore, process to fabricate the negatively charged TiO₂-coated Ps-beads can be established as testified samples for development of other microfluidic devices.

Hybrid metal-halide perovskites have emerged as leading class of semiconductors for photovoltaic devices with remarkable light harvesting efficiencies. The formation of methylammonium lead iodide (CH₃NH₃PbI₃) perovskite into mesoporous titania (TiO₂) scaffold by a sequential deposition technique is known to offer better control over the perovskite morphology. The growth reactions at the mesoporous TiO₂ film depend on reactants concentration in the host matrix and the reaction activation energy. Here, we are characterizing formation of CH₃NH₃PbI₃ perovskite in mimic solar cell photoelectrodes utilizing the developed NanoPlasmonic Sensing (NPS) approach. Based on dielectric changes at the TiO₂ mesoporous film interface, the technique provides time-resolved spectral shifts of the localized surface plasmon resonance that varies widely depending on the different operating temperatures and methylammonium iodide (CH₃NH₃I) concentrations. Analytical studies included Ellipsometry, Scanning Electron Microscopy, and X-ray diffraction. The results show that perovskite conversion can be obtained at lower CH₃NH₃I concentrations if reaction activation energy is lowered. A significant finding is that the NPS response at 350 nm mesoporous TiO₂ can widely change from red shifts to blue shifts depending on extent of conversion and morphology of perovskite formed at given reaction conditions.

Ionic liquids (ILs) have gained interest among researchers due to its tunable properties that can be used in wide applications. However, toxicity and bio-degradation studies of ILs proved that most of the aromatic ILs, such as imidazolium is highly toxic and non-biodegradable. Several advance oxidation processes (AOPs) have been investigated by researchers to evaluate the efficiency of the systems for the removal of ILs from wastewater. However, the issue on relative high cost and environmental concern has limited the application of these AOPs in industry. In this research, photocatalytic study using hybrid nano-materials was conducted to evaluate the efficiency of this system as an alternative AOP system for removal of ILs from wastewater. The synergistic effect of adsorption-photodegradation was introduced by depositing Fe-TiO₂ onto the functionalized activated carbon (AC). Nano-TiO₂ was synthesized using micromulsion method before modification with transition metal and deposited onto the oxidized AC. Photodegradation reaction of 1-butyl-3-methylimidazolium chloride [bmim]Cl was investigated under simulated visible light irradiation. It was observed that the overall efficiency of the system was increased with the increasing amount of Fe dopant. Investigation on the extrinsic factors such as solution pH, initial concentration of ILs and photocatalyst dosage showed to significantly affect the overall efficiency of the systems where the optimum condition for the system was observed at pH 10, with initial ILs at 1mM at 1 g/L of photocatalyst. The best performance photocatalyst was 0.2Fe-TiO₂/AC.

After 40 years of the discovery of metallocene catalysts, there are still several aspects that remain unresolved, especially when the “conventional” alkylaluminum activators are not used. Herein, we systematically investigate the synthesis of PE via three different zirconocene catalysts, with different alkyl substituents, activated via different organoboron compounds. The polymerization behavior, as well as the properties of the materials, are evaluated. The results demonstrate that the highest catalytic activity is shown by Bis(cyclopentadienyl)dimethylzirconium activated by trityl tetra(pentafluorophenyl)borate. Also finding that toluene is the optimum solvent for these systems and at these reaction conditions. Moreover, to validate our experimental results, a comprehensive mathematical model is developed on the basis of thermodynamic and kinetic principles. The concentration of ethylene transferred to the solvent phase (toluene) in a liquid-vapor equilibrium (LVE) system is estimated based on the Duhem’s theorem. Arrhenius expressions for the kinetic rate constants of a proposed kinetic mechanism are estimated by a kinetic model, in which the rate of polymerization is fitted by a least-square optimization procedure and the molecular weight averages by the method of moments. The simulations of the coordination polymerization suggest the presence of two types of active sites, principally at low temperatures, and the reactivation of the deactivated sites via a boron-based activator. However, the effect of the temperature on the reactivation step is no clear; a deeper understanding via designed experiments is required.

Titanium and its alloys are used biomaterials for medical and dental applications, due to their mechanical and physical properties. The surface modifications of titanium with bioactive molecules can increase the osseointegration by improving the interface between the bone and implant. Titanium dioxide nanotubes (TiO₂NTs) have excellent bioactivity inducing cell adhesion, spreading, growth and differentiation. In this work, TiO₂NTs were functionalized with a lectin from the plasma of the fish Oreochromis niloticus aiming to favour the adhesion and proliferation of osteoblast-like cells, improving its biocompatibility. The TiO₂NTs were obtained by anodization of titanium and annealed at 400 °C for 3 h. The resulting TiO₂NTs were characterized by high-resolution scanning electron microscopy. The successfully incorporation of OniL on the surface of TiO₂NTs by spin coating was demonstrated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIE) and attenuated total reflection-Fourier transform infrared spectrum (ATR-FTIR). Our results showed that TiO₂-NTs were successfully synthesized in a regular and well-distributed way. The functionalization of TiO₂-NTs with OniL favoured adhesion, proliferation, and the osteogenic activity of osteoblast-like cells, suggesting its use to improve the quality and biocompatibility of titanium-based biomaterials.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Patients with heart failure (HF) with improved LVEF (HFimpEF) demonstrate better clinical outcomes when compared with individuals without restoration of cardiac function. Identification of predictors for HFimpEF may play a crucial role in individual management of HF with reduced EF (HFrEF). Cell-free nuclear (cf-nDNA) DNA are released from damaged cells and contribute to adverse cardiac remodeling, cardiac dysfunction and inflammation. The purpose of the study was to elucidate whether cf-nDNAs are associated with HFimpEF. It has been prescreened 1416 patients with HF using local database. Between October 2021 and August 2022 we included 452 patients chronic HFrEF after prescription of optimal guideline-based therapy and identified HFimpEF in 177 individuals from them according to the criteria of European Society of Cardiology. Measurements of circulating biomarkers were performed at baseline and in 6 months. Detection of cf-nDNA was executed with real time quantitative PCR (qPCR) using NADH dehydrogenase, ND2 and beta-2-microglobulin. We found that HFimpEF was associated with a significant decrease in the levels of cf-nDNA when compared with the patients from persistent HFrEF cohort. Presence of ischemia-induced cardiomyopathy (odds ration [OR] = 0.75; confidence interval [CI] = 0.62 – 0.88; p = 0.044), type 2 diabetes mellitus (OR = 0.77; CI = 0.71 – 0.82; p = 0.042) and digoxin administration (OR = 0.85; CI = 0.72-0.97; p = 0.042) were negative factors for HFimpEF, whereas NT-proBNP ≤1940 pmol/mL (OR = 1.42; 95% CI = 1.19-1.98, p = 0.001), relative decrease in NT-proBNP levels (>35% vs. ≤35%) from baseline (OR = 1.52; 95% CI = 1.38-0.69, p = 0.001) and cf-nDNA ≤7.5 μmol/L (OR = 1.56; 95% CI = 1.07-2.94, p = 0.001) were positive predictors for HFimpEF. Multivariate logistic regression adjusted to ischemia-induced cardiomyopathy, IV HF NYHA class, and digoxin use yielded that NT-proBNP ≤1940 pmol/mL (OR = 1.43; 95% CI = 1.21-1.88, p = 0.001) and cf-nDNA ≤7.5 μmol/L (OR = 1.64; 95% CI = 1.19-2.15, p = 0.001) independently predicted HFimpEF. In conclusions: we established that the levels of cf-nDNA≤7.5 μmol/L independently predicted HFimpEF and improved discriminative ability of as single measured NT-proBNP as well as relative decrease in NT-proBNP levels ≤35% from baseline.

The optical characteristics and electrical behavior of zinc oxide nanorods (ZnO-NR) and silver nanoparticles (Ag-NP) were investigated using advanced scanning probe microscopy and spectroscopy techniques. The study revealed that the ZnO nanorods have a length of about 350 nm, while the Ag nanoparticles are spherical with heights ranging from 5 to 14 nm. Measurements with Kelvin Probe Force Microscopy (KPFM) showed that the work functions of ZnO nanorods are approximately 4.55 eV, higher than that of bulk ZnO, and the work function of Ag nanoparticles ranges from 4.54 to 4.56 eV. The electrical characterization of ZnO nanorods, silver nanoparticles, and their hybrid was also conducted using conductive atomic force microscopy (C-AFM) to determine the local current-voltage (I-V) characteristics, which revealed a characteristic similar to that of a Schottky diode. The current-voltage characteristic curves of ZnO nanorods and Ag nanoparticles both show an increase in current at around 1V, and the hybrid ZnONRs/AgNP exhibits an increase in turn-on voltage at around 2.5 Volts. This suggests that the presence of Ag nanoparticles enhances the electrical properties of ZnO nanorods, improving charge carrier mobility and conduction mechanisms through a Schottky junction. The investigation also explored the optical properties of ZnO-NR, AgNP, and their hybrid, revealing absorption bands at 3.11 eV and 3.18 eV for ZnO-NR and AgNP, respectively. The hybrid material showed absorption at 3.13 eV, indicating enhanced absorption, and the presence of AgNP affected the optical properties of ZnO-NR, resulting in increased photoluminescence intensity and slightly changes in peak positions.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

The real implementation of biogas reforming at industrial scale to obtain interesting products, like hydrogen or syngas, is a developing research field where multidisciplinary teams are continuously adding improvements and innovative technologies. Thus, these works can contribute to the proliferation of green technologies where circular economy and sustainability are present. To assess the sustainability of these processes, there are different tools like life cycle assessment (LCA), which implies a complete procedure where even small details count to consider a certain technology sustainable or not. The aim of this work was to review works where LCA is applied to different aspects of biogas reforming, especially focusing on the role of catalysts, which are essential to improve the efficiency of a certain process, but also present a strong influence on its environmental impact. As a conclusion, catalysts have an influence on LCA through the improvement on the catalytic performance and the impact of their production, whereas other aspects related to biogas or methane reforming could equally influence on their durability or reusability, with the subsequent effect on LCA. Further research about this subject is required in a continuously changing technology with plenty of possibilities.

Series of bifunctional catalysts, MoS2/Al2O3(70 wt.%)-zeolite (30 wt.%) (zeolite – ZSM-5, ZSM-12, ZSM-22 and silica aluminophosphate SAPO-11), were synthesized for hydroconversion of methyl palmitate (10 wt.% in dodecane) in a trickle-bed reactor. Mo loading was about 7 wt.%. Catalyst and supports were characterized by different physical-chemical methods (HRTEM-EDX, SEM-EDX, XRD, N2 physisorption, FTIR spectroscopy). Hydroprocessing was performed at temperature of 250-350°C, hydrogen pressure 3.0-5.0 MPa, liquid hourly space velocity (LHSV) 36 h-1, H2/feed ratio – 600 Nm3/m3. Complete conversion of oxygen-containing compounds was achieved at temperature 310°C in the presence of MoS2/Al2O3-zeolite catalysts, the selectivity for the conversion of methyl palmitate via the ‘direct’ hydrodeoxygenation (HDO) route was over 85%. The yield of iso-alkanes gradually increases in order: MoS2/Al2O3 < MoS2/Al2O3-ZSM-12 < MoS2/Al2O3-ZSM-5 < MoS2/Al2O3-SAPO-11 < MoS2/Al2O3-ZSM-22. The sample MoS2/Al2O3-ZSM-22 demonstrated the highest yield of iso-alkanes (40%). Hydroisomerization activity of the catalysts was in a good correlation with concentration of Brønsted acid sites of synthesized supports.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

Hydrogen evolution reaction (HER) is one of the most important reaction in electrochemistry. This is not only because it is the simplest way to produce high purity hydrogen and the fact that it is the side reaction in many other technologies. HER actually shaped current electrochemistry because it was in focus of active research for so many years (and it still is). The number of catalysts investigated for HER is immense, and it is impossible to overview them all. In fact, it seems that the complexity of the field overcomes the complexity of HER. The aim of this review is to point out some of the latest developments in HER catalysis, current directions and some of the missing links between a single crystal, nanosized supported catalysts and, recently emerging, single atom catalysts for HER

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Magnetic resonance (MR) image acquisitions are usually time-consuming, limiting utilization in neuroimaging. For multiple sclerosis (MS) patients, MR imaging plays a major role in drug therapy decision-making. The purpose of this study was to evaluate whether an ultrafast, T2-weighted (T2w), deep-learning-enhanced (DL), echo-planar-imaging-based (EPI) fluid-attenuated inversion recovery (FLAIR) sequence (FLAIRUF) that has been targeting neurological emergencies so far might even be an option to detect MS lesions of the brain compared to conventional FLAIR sequences. Therefore, 17 MS patients were enrolled prospectively in this exploratory study. Standard MR protocols and ultrafast acquisitions were conducted at 3 tesla (T), including three-dimensional (3D)-FLAIR, turbo/fast spin echo (TSE)-FLAIR, and FLAIRUF. Inflammatory lesions were grouped by size and location. Lesion conspicuity and image quality were rated on an ordinal five-point Likert scale, and lesion detection rates were calculated. Statistical analyses were performed to compare results. Altogether, 568 different lesions were found. Data indicated no significant differences in lesion detection (sensitivity and positive predictive value [PPV]) between FLAIRUF and axially reconstructed 3D-FLAIR (lesion size ≥ 3 mm × ≥ 2 mm) and no differences in sensitivity between FLAIRUF and TSE-FLAIR (lesion size ≥ 3 mm total). Lesion conspicuity in FLAIRUF was similar in all brain regions except for superior conspicuity in the occipital lobe and inferior conspicuity in central brain regions. Further findings include location-dependent limitations of signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) as well as artifacts such as spatial distortions in FLAIRUF. In conclusion, FLAIRUF could potentially be an expedient alternative to conventional methods for brain imaging in MS patients since the acquisition can be performed in a fraction of time while maintaining good image quality.

A new one-pot technique for preparation of polysaccharide-based Pd- and Pd-Ag nanocatalysts by sequential supporting natural polymer (2-hydroxyethyl cellulose (HEC), chitosan (Chit), pectin (Pec)) and metals on zinc oxide was developed. The nanocatalysts based on polysaccharide were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET), infrared spectroscopy (IRS), X-ray powder diffraction (XRD), X-ray photoelectron spectra (XPS) and elemental analysis methods. The catalyst characterization results indicated complete adsorption of polysaccharide and metal ions on zinc oxide, forming polymer-stabilized Pd nanoparticles of ~2 nm in size, evenly distributed on the support surface. The catalysts were studied in the hydrogenation of 2-hexyn-1-ol under mild conditions (0.1 MPa, 40 °C). The catalysts demonstrated nearly the same conversion of 2-hexyn-1-ol. The selectivity to cis-hexen-1-ol of the catalysts decreases in the following order: 0.5%Pd-Ag(3:1)HEC/ZnO>0.5%Pd-Ag(3:1)Pec/ZnO>0.5%Pd-Ag(3:1)Chit/ZnO. The optimum reaction temperature and catalyst loading for the Pd-Ag catalysts modified with HEC and Chit have been determined (40 °C, 0.05 g).

This study investigates the cytotoxicity profile of superparamagnetic Fe3O4-Ag decorated nanoparticles against human fibroblasts (HFF-1) and breast cancer cells (MCF-7). The nanoparticles underwent comprehensive characterization employing scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and magnetic assays including hysteresis curves and zero-field-cooled (ZFC) plots. Notably, the nanoparticles exhibited superparamagnetic behavior as evidenced by magnetic studies. Remarkably, cytotoxicity assays demonstrated that both HFF-1 and MCF-7 cells maintained nearly 100% viability upon nanoparticle exposure. These results underscore the outstanding biocompatibility of Fe3O4/Ag decorated nanoparticles, suggesting their potential utility in biomedical applications such as drug delivery and magnetic targeting without inducing significant cytotoxic effects. This investigation advances our understanding of the behavior of nanostructured materials in biological settings and highlights their promising prospects in biomedicine.

Gold nanoparticles, were deposited in titanium oxide (TiO2) Degussa-P25 with the Photodeposition method in the presence of UV light at different concentrations. It was determined by diffuse reflectance (DF), Scanning electron microscopy (SEM), that the Photodeposition method is effective for the inclusion of gold particles on the surface. The catalyst band gap showed a reduction to 2.9 e.V, as well as it was observed that the gold-doped catalyst shows absorption in the visible light range around 500 to 600 nm. The percentage of deposited gold nanoparticles was determined by energy dispersive spectroscopy (EDS). The experimental data were analyzed using different analytical techniques (UV-Vis spectrophotometry, TOC total organic carbon), with these results a carbon-based mass balance and reaction kinetics were generated using the Langmuir-Hinshelwood (LH-HW) heterogeneous catalysis model. For the estimation of the kinetic constants, the non-linear regression of the Levengerd Marquad algorithm was used, with these results, kinetic models of the degradation of the molecule and the generation and consumption of Organic Intermediate Products (OIP) were generated.

Catalytic hydrogenation of a biomass-derived molecule, levulinic acid (LA) to γ-valerolactone (GVL) has been getting a lot of attention from researchers across the globe recently. This is because GVL has been identified as one of the potential molecules for the replacement of fossil fuels. For instance, GVL can be catalytically converted into liquid alkenes in the molecular weight range close to that found in transportation fuels via a process that does not require an external hydrogen source. Noble and non-noble metals have been used as catalysts for the selective hydrogenation of LA to GVL. Of these, Ru has been reported to be the most active metal for this reaction. The type of metal supports and solvents has been proved to affect the activity, selectivity, and yields of GVL. Water has been identified as a potential, effective “green” solvent for the hydrogenation of LA to GVL. The use of different sources of H2 other than molecular hydrogen (such as formic acid) has also been explored. In a few instances, the product, GVL, is hydrogenated further to other useful products such as 1,4-pentanediol (PD) and methyl tetrahydrofuran (MTHF). This review selectively focuses on the potential of immobilized Ru catalysts as a potential superior catalyst for selective hydrogenation of LA to GVL.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

Mechanical robustness, biocompatibility, and antibacterial performances are key features for materials suitable to be used in tissue engineering applications. In this work, we investigated the link existing between structural and functional properties of TiCu(Ag) thin films deposited by physical vapor deposition magnetron sputtering on Si substrates. The thin films were characterized by X-ray diffraction (XRD), nanoindentation, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The TiCu(Ag) thin films showed complete amorphous structure and improved mechanical properties in comparison with pure Ti films. However, for contents in excess of 20% Ag, we observed the appearance of nanometric Ag crystallite. The TiCu(Ag) thin films displayed excellent biocompatibility properties, allowing adhesion and proliferation of the human fibroblasts MRC-5 cell line. Moreover, all the investigated TiCu(Ag) alloy display bactericidal properties, preventing the growth of both Pseudomonas aeruginosa and Staphylococcus aureus. Results obtained from biological tests have been correlated to the surface structure and microstructure of films. The excellent biocompatibility and bactericidal properties of these multifunctional thin films opens to their use in tissue engineering applications.

The variation of the cationic composition in I2-II-IV-VI4 semiconductor compounds is an effective tool for altering their properties in a controlled manner. In particular, a partial substitution of Cu for Ag in kesterite Cu2ZnSnS4 was proposed to suppress Cu-Zn antisite defects and the improve photovoltaic performance. However, the efficiency of this approach may substantially depend on the fabrication route. Here, we report on the synthesis of (Cu,Ag)-Zn-Sn-S (CAZTS) and Ag-Zn-Sn-S (AZTS) nanocrystals (NCs) by means of "green" chemistry in aqueous solution and their detailed characterization by Raman spectroscopy and by several complementary techniques. Through a systematic variation of the nominal composition and quantification of the constituent elements in CAZTS and AZTS NCs by XPS, we identified the vibrational Raman and IR fingerprints of both the main AZTS phase and secondary phases of Ag-Zn-S and Ag-Sn-S compounds (for the first time). The formation of the secondary phases of Ag-S and Ag-Zn-S cannot be avoided entirely for this type of synthesis. The Ag-Zn-S phase, having its bandgap in near infrared range, is the reason of the non-monotonous dependence of the absorption edge of CAZTS NCs on the Ag content, with a trend to redshift even below the bandgaps of bulk AZTS and CZTS.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO2 has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O2-, ·OH), yet the low specific surface area of crystalline TiO2 depressed the catalytic performance. Herein, we prepared TiO2 aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO2 aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO2 aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO2 aerogel for the photocatalytic HCHO decomposition is 2 nm-10 nm. This study provides a theoretical idea for TiO2 aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO2 aerogels for green chemistry.

The novel ternary composites, BiOBr-TiO2-attapulgite (BTA), were synthesized using a simple hydrothermal and water-bath method, exhibiting excellent photocatalytic performance to mul-tiple xanthates. For BTA photocatalyst, TiO2 and BiOBr were uniformly loaded on the surface of acid-activated attapulgite. As a widely used collector in mining processes, sodium ethyl-xanthate (SEX) was selected as the target pollutant due to its high toxicity. The BTA ternary photocatalyst demonstrated significantly higher adsorption and photocatalytic degradation performance compared to TiO2 nanoparticles, BiOBr nanosheets, and BiOBr-TiO2 heterojunction. Structural characterization and experimental results indicated that the exceptional photocatalytic degrada-tion efficiency of BTA was mainly attributed to the formation of heterojunction between BiOBr and TiO2, as well as the presence of additional active adsorption sites provided by attapulgite. Free radical scavenging experiments and EPR results confirmed that the photogenerated holes were the predominant active species to photodegrade SEX throughout the entire experiment. The LC-MS results provided insight into potential degradation pathways of SEX. This research demonstrates that BTA, as a novel triple composite material, achieves rapid and complete degradation to 20 mg/L SEX within 20 min. This work presents a novel approach to synthesize mineral-based photo-catalysts, which have broad prospects for application in flotation wastewater treatment.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

The photocatalysis process over N-doped TiO2 under visible light is examined for Pb(II) oxidation to form the less toxic and handleable PbO2 suggesting a new method for Pb(II) remediation. The doping TiO2 with N element was conducted by simple hydrothermal technique and using urea as the N source with various concentrations. The doped photocatalysts were characterized by DRUVS, XRD, FTIR and SEM-EDX instruments. Photocatalysis of Pb(II) through batch experiment was performed for evaluation of the doped TiO2 activity under visible light, with applying various fractions of N doped, photocatalyst weigh, irradiation time, and solution pH. The research results attributed that N doping has been successfully performed, that shifted TiO2 absorption into visible region, allowing it to be active under visible irradiation. The photocatalytic removal of Pb(II) under visible ligth over N-TiO2 showed more effective than that of over the un-doped photocatalyst. The removal of Pb(II) has notably taken place through oxidation, that may form PbO2. The highest photocatalytic oxidation of Pb(II) 15 mg/L in 25 mL of the solution could be reached by using TiO2 doped with 10%w of N, 15 mg of N-TiO2 weight, 30 minutes of time, and at pH 8, suggesting a feseable method for Pb(II) remediation.

The preparation of immobilized graphene–based photocatalyst layers is highly desired for environmental applications. In this study, the preparation of an immobilized reduced graphene oxide (rGO)/TiO₂ composite by electrophoretic deposition (EPD) was optimized. It enabled quantitative deposition without sintering and without the use of any dispersive additive. The presence of rGO had beneficial effects on the photocatalytic degradation of 4-chlorophenol in an aqueous solution. A marked increase in the photocatalytic degradation rate was observed, even at very low concentrations of rGO. Compared with the TiO₂ and GO/TiO₂ reference layers, use of the rGO/TiO₂ composite (0.5 wt% of rGO) increased the first-order reaction rate constant by about 70%. This enhanced performance was due to the increased formation of hydroxyl radicals that attacked the 4-chlorophenol molecules. The direct charge transfer mechanism had only limited effect on the degradation. Thus, EPD-prepared rGO/TiO₂ layers appear to be suitable for environmental application.

Two-dimensional arrays of hollow nanotubes made of TiO2 are a promising platform for sensing, spectroscopy and light harvesting applications. Their straightforward fabrication via electrochemical anodization, growing nanotube pillars of finite length from a Ti foil, allows precise tailoring of geometry and, thus, material properties. We investigate these photonic crystal structures with respect to reduction of front surface reflection, achievable field enhancement, and photonic bands. With the Rigorous Coupled Wave Analysis (RCWA), we study the optical response of photonic crystals made of thin-walled nanotubes relative to the bare Ti foil substrate, including under additional charge carrier doping.

In this study, TiO2 nanostructured coatings on Ti-6A-4V alloys were fabricated by two methods: H2O2 oxidation and RF sputtering. In the annealing temperature range of 25 C - 500 C, there were the peaks at 35, 37, 40 and 52 corresponding to {100}, {002}, {101} and {102} crystal planes of hcp structure of α-Ti. At the annealing temperature of 600 C, there was the presence of peaks corresponding to crystal planes of anatase and rutile TiO2. The relative intensities of anatase and rutile phases of the sample fabricated by RF sputtering were 3.62 and 10.25 %, respectively; while those of the sample fabricated by H2O2 oxidation were 21.27 and 3.20 %, respectively (The relative intensity of α-Ti phase was 100 %). The results investigated the peak shift of α-Ti phase in TiO2/Ti-6Al-4V nanostructured coatings fabricated by the two methods which was reasonably explained from the difference in the thermal expansion coefficients of Ti alloy and TiO2 components, as well as the difference in the ratio of anatase to rutile phases.

The direct hydrogenation of greenhouse gas carbon dioxide (CO2) to higher alcohols (C2+OH), as an important research area in C1 chemistry, is one of the most essential approaches to convert CO2 into liquid fuels or other value-added chemicals. The high atom economy and direct pathway make this reaction attractive to convert CO2 to higher alcohols. However, due to the complicated reaction network and the difficulty of C-C coupling, the formation of higher alcohols is more difficult compared with methanol or other compounds containing one carbon. The key issue is development of novel catalysts with high conversion and space time yield. But this is still a huge challenge faced by researchers. In this review, the thermodynamics and reaction pathways of CO2 hydrogenation were firstly clarified. Subsequently, after reviewing single metal-based, bi-and multi-metallic catalysts, the recently progress of tandem catalytic system was emphasized. Finally, we also provided an overview about tandem catalysis for CO2 hydrogenation to higher alcohols.

This study investigates the role of oxygen vacancy on Fe-doped CeO₂ catalyst activity for soot oxidation. The oxygen vacancy was assessed through Ce³⁺ content. The Fe content was varied between 0 and 30% for two catalyst preparation methods, co-precipitation (CP) and solution combustion synthesis (SCS). X-ray photoelectron spectroscopy indicates that ceria exists as both Ce₄₊ and Ce₃₊, while iron is present only as Fe₃₊. The catalyst’s activity was evaluated by ignition (T10) and combustion (T50) temperatures using thermogravimetric analysis. Optimum Fe contents yielding the highest activity were found to be 10% and 5% for CP and SCS catalysts, respectively. The surface area and morphology have shown moderate effect on catalyst activity, because catalytic soot oxidation involves solid-solid contact. More importantly, regardless of the fabrication method, it was found that Ce₃₊ content, which is closely related to oxygen vacancies, plays the most important role in affecting the catalyst activity.

In this study, a new method for synthesizing Ag-NaYF4:Yb3+/Er3+ @ SiO2 nanocomposites was introduced. Using a hydrothermal method, the synthesized Yb3+- and Er3+-codoped NaYF4 upconversion luminescent materials and Ag nanoparticles were doped into upconversion nanomaterials and coated with SiO2 up-conversion nanomaterials. This material is known as Ag-UCNPs-SiO2’ it improves both the luminous intensity because of the doped Ag nanoparticles and has low cytotoxicity because of the SiO2 coating. The morphology of UCNPs was observed using scanning electron microscopy (SEM), and the mapping confirmed the successful doping of Ag nanoparticles. Successful coating of SiO2 was confirmed using transmission electron microscopy (TEM). Fluorescence spectra were used to compare changes in luminescence intensity before and after doping Ag nanoparticles. The reason for the increase in luminescence intensity after doping with Ag nanoparticles was simulated using first-principles calculations. The cytotoxicity of Ag-UCNPs-SiO2 was tested via the cell counting kit-8 (CCK-8) method, and its imaging ability was characterized using the micro-CT method.

Metallic elements of higher economic value occurring in the mineralogy of Zimapán are Pb, Zn, Cu and Fe, said elements are sold as concentrates, which, even after processing, generally include significant concentrations of Mo, Cd, Sb, Ag and As that could recover through different leaching methods. In this work the influence of temperature was studied in the complexation of silver in the S₂O₃^2--O₂ system. Chemical and mineralogical characterization of concentrated Zn from the state of Hidalgo confirmed the presence of the silver contained in a sulfide of silver arsenic (AgAsS₂) through the techniques of Atomic Absorption Spectrophotometry (AAS), X-Ray Diffraction (XRD) and Scanning Electron Microscopy-Energy-Dispersive X-Ray Spectroscopy (SEM-EDS). The mineralogical species identified allowed the construction mineralogical species Pourbaix diagrams in the range of 298 K to 333 K, through which the Eh-pH conditions to obtain silver in solution were determined. The formation of Ag(S₂O₃)₂^3- complex was confirmed by characterizing liquors leached using the technique Infrared Spectroscopy Fourier Transform (FTIR).

Reverse water gas shift reaction (RWGS) is an important process which plays a vital role in many CO2 utilization related reactions. Noble metals are the most active catalysts in RWGS, but the high price and low reserve strangled their applications. In the present work, we reported a non-transition-metal MgAl2O4 catalyst which showed outstanding activity and stability at high temperatures in the RWGS reaction and improved performance after doping of single atomic Nin+. The catalyst can obtain 46% of CO2 conversion in durability test of 75 h at 800 °C under high weight hourly space velocities (225 000 ml g-1 h-1). The adsorption sites, possible reaction route, and effects of Nin+ single atoms on the (111) surface of MgAl2O4 for RWGS were investigated by in situ DRIFTS and DFT calculations. The results indicated that the rate determining reaction step of RWGS on MgAl2O4 and Ni (SA)/MgAl2O4 were both the reaction of OH* + H* → H2O* + *, but the energy barrier was significantly reduced after introducing single atomic Nin+. Nin+ atoms can increase the hydroxyl coverage on the surface of catalyst and Al3+ sites near the Nin+ ion are considered as the predominant active sites for RWGS reactions.

The tunable work function of titanium dioxide (TiO₂) nanoparticles of various sizes was measured using the Kelvin Probe Force Microscopy (KPFM) technique. The analysis of the contact potential difference (CPD) across TiO₂ nanoparticles of different sizes revealed a clear relationship between nanoparticle size, surface roughness, and work function. The study observed work function values ranging from 4.49 eV to 4.57 eV for particle sizes between 3 nm and 85 nm, which were higher than those of bulk TiO₂, likely due to quantum confinement effects. Additionally, electrostatic force microscopy (EFM) measurements showed significant charge-trapping behavior within TiO₂ nanoparticles under different applied bias voltages. The optical analysis also revealed a quantum confinement-induced band gap of 3.35 eV, larger than that of bulk TiO₂, and distinct photoluminescence peaks at 383 nm and 403 nm, corresponding to near-band-edge excitonic emissions and defect-related states. By analyzing the conduction band (CB) and valence band (VB) of TiO₂ nanoparticles using KPFM, the CB and VB positions were calculated based on work function data and bandgap. The results indicated that as particle size increases, both CB and VB energies shift slightly towards lower values, where smaller nanoparticles exhibit larger band gaps and higher work functions.

The Covid-19 pandemic and the initial focus on handwashing measures have again highlighted the importance of water access as an essential service in protecting human health. Yet, especially in southern cities, uneven geographies of water access – often mediated by fragmented and unequal infrastructure systems – may hamper the fight against infectious diseases. The spread of SARS-CoV-2 presented a dilemma for water providers as well as residents in water-deprived urban areas as they had to adhere to new hygiene standards and requirements, despite limited access to basic water infrastructure. Therefore, a deeper understanding of pandemic urban waterscapes – the infrastructure and governance systems as well as everyday practices and technologies – is necessary for ongoing debates on (post-) pandemic or zoonotic cities. In our paper, we focus on changes in urban (water) governance and government water projects in Nairobi since early 2020. We show that Covid-19 has contributed to changes in Nairobi’s waterscape but only in conjunction with recent changes in the city’s overall governance structure. However, if these waterscape changes lead to greater equity in water access, and if they have helped to curb the spread of SARS-CoV-2, is more than questionable.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

Due to the deteriorating state of surface waters and the resulting reduction in their availability for the population, efforts have been undertaken to develop a biodegradable or compostable water filtration system capable of reducing the amount of harmful bacteria in this environment. The aim of this research was to develop nonwovens using the classic needle-punching method with commercially available polylactide (PLA) polymer, and subsequently, to select appropriate concentrations of modifiers to create systems with antibacterial properties. The resulting composites could potentially serve as filtration materials for the purification of surface waters. Nanoparticles such as zinc oxide, titanium dioxide, and silver were employed in this research. These compounds exhibit antibacterial properties and are insoluble in water. To confirm the bactericidal activity of the additives, biological tests were conducted, and the distribution of these additives on the structure of the filtration material was examined using scanning electron microscopy (SEM) equipped with an energy dispersive spectroscopy (EDS) detector.

In this study, silver-strontium doped hydroxyapatite (AgSr-HA)/chitosan composite coatings were deposited on stainless steel (SS) substrate via electrophoretic deposition (EPD) technique. The EPD parameters such as the concentration of Ag Sr-HA particles in the suspension, applied voltage and deposition time were optimized on by the Taguchi Design of Experiment (DoE) approach. DOE approach elucidated that the “best” coating was obtained at; the deposition voltage of 20V, deposition time of 7 minutes, and at 5 g/L of Ag Sr-HA particles in the suspension. The optimum coatings were characterized by using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy. SEM images confirmed the deposition of chitosan/Ag Sr-HA on the SS substrate. The wettability studies indicated the hydrophilic nature of the chitosan/Ag Sr-HA coatings, which confirmed the suitability of the developed coatings for orthopedic applications. The average surface roughness of the chitosan/Ag Sr-HA coatings was in a suitable range for the attachment of bone marrow stromal cells. Chitosan/Ag Sr-HA coatings showed a potent antibacterial effect against the Gram-Positive and Gram-negative bacteria.

Small rodents and insectivores are potential reservoirs of many pathogens transmissible to humans such as bacteria, parasites and viruses responsible for epidemics in sub-Saharan Africa, particularly in West Africa. Few studies on small mammal species in the Kolikoro and Sikasso regions are available, hence the interest in investigating the different species of small rodents and insectivores, and their role in the transmission of pathogens to humans. The study aims to identify commensal small mammal species circulating in Faladjè and Bougouni areas, and likely to represent major risks of epidemic disease emergence. Sessions of trapping were carried out in December 2016 in Faladjè and Bougouni with wire mesh traps type “Besançon tous services” (BTS) baited with peanut butter and/or onion. All animals captured were identified morphologically. Out of 123 small rodents and insectivores captured in 674 trap nights, 75 (60.97%) were from Faladjè and 48 (39.02%) from Bougouni, Of these, six species of small rodents belong to the family Muridae (Mastomys erythroleucus, Mastomys natalensis, Rattus rattus, Praomys daltoni, Gerbilliscus gambianus, Taterillus gracilis) and two species of insectivores associated with the genus Crocidura spp. belong to the family Soricidae and Erinaceidae (Crocidura cf olivieri and Atelerix cf albiventris) respectively. There is low specific diversity within these two stands, but the variation in relative abundance is significant (binomial test, p = 0.018 ˂ 0.05) between the Faladjè and Bougouni stands of small mammals. Mastomys erythroleucus was the most dominant species (57.33%, 43/75) in the Faladjè settlement and R. rattus dominated (37.5%,18/48) that of Bougouni. These two species of small mammals are potentially involved in the transmission of bacteria, parasites and pathogenic viruses to humans.

The Computational theoretical techniques using first principle which make use of the density functional theory as implemented by quantum expresso as well as inter – atomic force constant (IFC) techniques (Born-von Jarman) were used to investigate the phonon dispersion curves of Silver (Ag) and Gold (Au) The results obtained show that for Au, the extension to 1 – 6^th neighbour gave slightly close agreement with the experimental phonon dispersions when compared to the 1 – 5^th neighbor at W_T and L_L symmetry points. The percentage error for Au at W_T are 2.5% and 2.9% ; at point L_L we obtained 0.6% and 0.7% respectively. The Local density Approximation (LDA) results for Ag underestimates the lattice with about 1.6% while the Generalized Gradient Approximation (GGA) overestimates it by 1.9%.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

Herewith we report a facile synthesis of zinc oxide doped with (5, 10, 15, and 20 wt%) titanium oxide nanocomposites in gelatin under ultra-sonication. The X-ray diffraction (XRD) data revealed ZnO the formation in addition to a rutile phase TiO2. The ZnO phase size decreased, and the rutile TiO2 phase increased with a TiO2 loading increment. The scanning electron microscopy (SEM) displayed a combination of spherical and hexagonal particles with a 60 – 80 nm size distribution. The prepared nanostructures photocatalytic activity was assisted using Rhodamine B dye, where they showed enhanced photodegradation competence under visible light irradiation. The kinetics of photodegradation followed the first-order kinetics with the 20 % wt sample having the maximum activity. The mechanistic investigation revealed the dominance of h+ and •O2- species during the dye photodegradation. The results indicate the potential application of such gelatin stabilized nanostructures for dye illumination from aqueous solutions under sunlight.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

In the face of the current energy and environment problems, the full use of biomass resources instead of fossil energy to produce a series of high-value chemicals has great application prospects. 5-hydroxymethylfurfural (HMF), which can be synthesized from lignocellulose as raw material, is an important biological platform molecule. Its preparation and catalytic oxidation of subsequent products have important research significance and practical value. In the actual production process, porous organic polymer (POPs) catalysts are highly suitable for biomass catalytic conversion due to its high efficiency, low cost, good designability, and environmentally friendly features. Here, we briefly described the application of various types of POPs (including COFs、PAFs、HCPs、CMPs) in the preparation and catalytic conversion of HMF from lignocellulosic biomass, and analyzed the influence of the structural properties of catalysts for the catalytic performance. Finally, we summarized some challenges that POPs catalysts will face in biomass catalytic conversion, and prospected the important research directions in future. This review would provide valuable references for the efficient conversion of biomass resources into high-value chemicals in practical applications.

Removing one key barrier to the industrial uptake of green chemistry and nanocatalysis in the fine and specialty chemical industry requires to fill an ongoing “talent shortage” via expanded chemistry education. In this study we show how the use of hybrid sol-gel catalysts to synthesize fine chemicals and active pharmaceutical ingredients in flow chemistry reactors illustrates new ideas to reshape chemistry education based on recent research outcomes, visualization and digital tools. Several lessons learned from the industrial and academic utilization of these materials in continuous-flow conversions conclude the study.

A series of Zn-modified Hβ (Zn/Hβ) catalysts were prepared by using the different zinc precursors such as ZnSO4·7H2O, ZnCl2, C4H6O4Zn·2H2O and Zn(NO3)2·6H2O, and their catalytic performance in the ethanol conversion to propylene reaction was evaluated. Results indicate the amount and strength distribution of acid sites of the Zn/Hβ catalysts were easily tuned by employing different type of zinc precursors. More importantly, when the Zn species were introduced to the Hβ, the propylene yield was significantly enhanced, whereas the yields of the byproducts such as ethylene and C2-C4 alkanes were remarkably suppressed. For the catalyst prepared by using the ZnCl2 precursor (Zn/Hβ-C), a higher propylene yield up to 43.4% was achieved as a result of the moderate amount and distribution of acid sites. The average coking rate of the used Zn/Hβ catalysts strongly depended on the amount of total acid sites, especially the strong acid sites, i.e., the higher the amount of total acid sites of the catalyst, the greater the average coking rate. For the catalyst prepared by using the ZnSO4·7H2O precursor, Zn/Hβ-S exhibited a better stability even after depositing more coke, which is due to the higher amount of strong acid sites.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

In this work, magnetic CuFe₂O₄/Ag nanoparticles activated by porous covalent organic frameworks (COF) was fabricated to evaluate the heterogenous reduction of 4-nitrophenol (4-NP). The core-shell CuFe₂O₄/Ag@COF was successfully prepared by polydopamine reduction of silver ions on CuFe₂O₄ nanoparticles, followed by COF layer condensation. With integrating the intrinsic characteristics of the magnetic CuFe₂O₄/Ag core and COF layer, the obtained nanocomposite exhibited features of high specific surface area (464.21 m² g^-1), ordered mesoporous structure, strong environment stability, as well as fast magnetic response. Accordingly, the CuFe₂O₄/Ag@COF catalyst showed good affinity towards 4-NP via π-π stacking interactions and possessed enhanced catalytic activity compared with CuFe₂O₄/Ag and CuFe₂O₄@COF. The pseudo-first-order rate constant of CuFe₂O₄/Ag@COF (0.77 min^-1) is 3 and 5 times higher than CuFe₂O₄/Ag and CuFe₂O₄@COF, respectively. The characteristics of bi-catalytic CuFe₂O₄/Ag and the porous COF shell of CuFe₂O₄/Ag@COF made a contribution to improve the activity of 4-NP reduction. The present work demonstrated a facile strategy to fabricate COF activated nano-catalysts with enhanced performance in the fields of nitrophenolic wastewater treatment.

The surface enhanced fluorescence（SEF）detection bases by plasmonic nanopillars array with nanoparticles has opened up a new gate in the application of biological imaging and sensing. The fluorescence enhancement of the probe molecule depends on its position in equilibrium, which is close to the hot spot leading to the electromagnetic field enhancement, but not too close to the metal surface resulting in quenching. Here, a large scale SiO₂-Ag-cicada wing SEF substrate was fabricated by magnetron sputtering with correction enhancement factor of 797.6. Thereinto the cicada wing provides the skeleton of the nanopillars array structure, the deposited Ag constructs two kinds of hot spots, and SiO₂ forms a separation layer to prevent quenching. Moreover, the substrate exhibited good reproducibility, high sensitivity with low limits of detection (LOD) and high stability for oxidation resistance. We propose that SEF substrate with modification of SiO₂ can not only improve the enhancement performance, but also expanding its application in the biological investigations.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

Photocatalytic processes offer promising solutions for environmental remediation and clean energy production, yet their efficiency under visible light remains a significant challenge. Here, we report a novel silver-graphene (Ag-G) modified TiO2 (Ag-G-TiO2) nanocomposite photocatalyst that demonstrates remarkably enhanced photocatalytic activity for both dye wastewater degradation and hydrogen production under visible and UV light irradiation. Through comprehensive characterization and performance analysis, we reveal that the Ag-G modification narrows the TiO2 bandgap from 3.12 eV to 1.79 eV, enabling efficient visible light absorption. The nanocomposite achieves a peak hydrogen production rate of 191 μmolesg-1h-1 in deionized water dye solution under visible light, significantly outperforming unmodified TiO2. Intriguingly, we observe an inverse relationship between dye degradation efficiency and hydrogen production rates in dye solutions with tap water versus deionized water, highlighting the critical role of water composition in photocatalytic processes. Our findings demonstrate sustained hydrogen production under visible light and rapid initial rates under UV irradiation, underscoring the versatility of Ag-G-TiO2 catalyst. This work not only advances our understanding of fundamental photocatalytic mechanisms but also presents a promising material for solar-driven environmental and energy applications, potentially contributing to the global transition towards sustainable technologies.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

Streptococcus mutans is well known for having virulence factors associated with its cariogenic role, such as glucosyltransferases, which have been used as targets for the virtual screening of molecules with inhibitory capacity. The Antigen I/II of S. mutans is involved in the adhesion to the surface of the tooth and the bacterial co-aggregation in the biofilm formation, despite that, this protein has not been used as a target in a virtual strategy search for inhibitors. In this study we identified in silico and evaluated in vitro molecules with adhesion inhibitory potential on S. mutans Ag I/II. A virtual screening of 883,551 molecules was conducted, cytotoxicity analysis on fibroblast cells, S. mutans adhesion studies, scanning electron microscopy analysis for bacterial integrity, and molecular dynamics simulation were also performed. We have found three molecules (ZI-187, ZI-939, ZI-906) that were not cytotoxic and inhibited the adhesion of S. mutans to polystyrene microplates. Molecular dynamic simulation by 300 nanoseconds showed stability of the interaction between ZI-187 and Ag I/II (PDB: 3IPK). This work provides three new molecules that targets Ag I/II and have the capacity to inhibit in vitro the S. mutans adhesion on polystyrene microplates and provides a new computational line for the search and selection of safe inhibitory molecules against different pathogens.

PEBAX-2533/metal salt/Al salt membranes were prepared for mixed olefin/paraffin separation. PEBAX-2533 with 80% ether group and 20% amide group was suggested as the polymer matrix for comparison of separation performance according to the functional group ratio in copolymer PEBAX. In addition, Al salts were used to stabilize metal ions for a long time as additives. High permeance was expected with the proportion of high ether groups since these functional groups provided relatively permeable regions. As a result, the PEBAX-2533 composite membrane showed a selectivity of 5 (propylene/propane) with 10 GPU. However, the permeance of membrane was not unexpectedly improved and the selectivity was reduced. The result was analyzed by SEM, FT-RAMAN and TGA, including FT-IR. The reduction in separation performance was determined by FT-IR. From these results, in order to stabilize the metal ions interacting with the polymer through Al(NO3)3, it was concluded that specific ratio of amide group was needed in PEBAX as polymer matrix.

PdRe/Al2O3 catalysts are highly selective for hydrogenation of furfural to furfuryl alcohol (FAL). Moreover, synergy between the metals can result in greater specific activity (higher turnover frequency, TOF) than exhibited by either metal alone. Bimetallic catalyst structure depends strongly on the metal precursors employed and their addition sequence to the support. In this work, PdRe/Al2O3 catalysts were prepared by: (i) co impregnation (CI) and sequential impregnation (SI) of  Al2O3 using HReO4 and Pd(NO3)2, (ii) SI using NH4ReO4 and [Pd(NH3)4(NO3)2], (iii) HReO4 addition to a reduced and passivated Pd/Al2O3 catalyst, and (iv) impregnation with the double complex salt (DCS), [Pd(NH3)4(ReO4)2]. Raman spectroscopy and temperature-programmed reduction (TPR) evidence larger supported PdO crystallites in catalysts prepared using Pd(NO3)2 than [Pd(NH3)4(NO3)2]. Surface [ReO4]- species detected by Raman exhibit TPR peak temperatures from ranging 85 to 260°C (versus 375°C for Re/Al2O3). After H2 reduction at 400°C, the catalysts were characterized by chemisorption, temperature-programmed hydride decomposition (TPHD), CO diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and scanning transmission electron microscopy (STEM) with energy-dispersive x-ray (EDX) spectroscopy. The CI catalyst containing supported Pd-Re alloy crystallites had a TOF similar to Pd/Al2O3 but higher (61%) FAL selectivity. In contrast, catalysts prepared by methods (ii-iv) containing supported Pd-Re nanoparticles exhibit higher TOFs and up to 78% FAL selectivity.

Network effects, economies of scale, and lock-in-effects increasingly lead to a concentration of digital resources and capabilities, hindering the free and equitable development of digital entrepreneurship (SDG9), new skills, and jobs (SDG8), especially in small communities (SDG11) and their small and medium-sized enterprises (“SMEs”). To ensure the affordability and accessibility of technologies, promote digital entrepreneurship and community well-being (SDG3), and protect digital rights, we propose data cooperatives [1,2] as a vehicle for secure, trusted, and sovereign data exchange [3,4]. In post-pandemic times, community/SME-led cooperatives can play a vital role by ensuring that supply chains to support digital commons are uninterrupted, resilient, and decentralized [5]. Digital commons and data sovereignty provide communities with affordable and easy access to information and the ability to collectively negotiate data-related decisions. Moreover, cooperative commons (a) provide access to the infrastructure that underpins the modern economy, (b) preserve property rights, and (c) ensure that privatization and monopolization do not further erode self-determination, especially in a world increasingly mediated by AI. Thus, governance plays a significant role in accelerating communities’/SMEs’ digital transformation and addressing their challenges. Cooperatives thrive on digital governance and standards such as open trusted Application Programming Interfaces (APIs) that increase the efficiency, technological capabilities, and capacities of participants and, most importantly, integrate, enable, and accelerate the digital transformation of SMEs in the overall process. This policy paper presents and discusses several transformative use cases for cooperative data governance. The use cases demonstrate how platform/data-cooperatives, and their novel value creation can be leveraged to take digital commons and value chains to a new level of collaboration while addressing the most pressing community issues. The proposed framework for a digital federated and sovereign reference architecture will create a blueprint for sustainable development both in the Global South and North.

A complementary characterisation of the Al-alloy EN AW-5454 was carried out, intended for obtaining the laser hybrid welding parameters of sub-assemblies in the automotive industry. The investigation included a microstructural examination, and determination of the alloy's properties using several analytical methods (HV5 hardness measurement, tensile test, Charpy impact toughness, fracture mechanics analysis). Samples were prepared in the longitudinal and transverse directions of a cold-rolled sheet of EN AW-5454 with thicknesses of 3.5 mm and 4 mm. The measured hardness on the thinner sheet was 5% higher than on the thicker sheet. The tensile and yield strength were nominal, while the elongations were smaller by 2.2 - 3.2% for the longitudinal samples and by 2.7 - 13.7% for the transverse samples. The smaller deviations from the nominal values are for the thinner sheet metal. A precise topographical analysis showed brittle fractures of the samples. The Charpy impact toughness results on the thicker plate showed a 20% greater work needed to break it in the longitudinal direction than in the transverse direction. With the thinner sheet metal, 40% greater work was needed. SEM (Scanning Electron Microscope) analysis has shown that the intermetallic Al6(Mn,Fe) particles in the longitudinal samples were mostly intact, with evidence of tough areas on the upper part of the fracture, indicating a better toughness than the specimens in the transverse direction. More crushed intermetallic particles were observed at the fractures of the transverse samples, and their distribution appeared to be more oriented in the direction of rolling. Fracture mechanics SENB (single edge notch bending) tests and their analysis showed that the resistance of the material to crack propagation in the longitudinal sample was about 50% greater than that in the transverse sample. SEM analysis of the fractures showed that the state of the intermetallic particles in the fracture mechanics testing, and the fracture mechanism differed from the one in the Charpy fractures.

Increasing photon absorption by capturing light is an important way to increase the efficiency of photovoltaic devices. In this regard, the small optical band gap (Eg) and high absorption coefficient of Se-containing thin nanofilms make them ideal for next generation photovoltaic devices based on selenides. This study reports on chemical synthesis processes in a bath for the insertion of amorphous selenium into polyamide-6 (PA 6) matrix and the effect of incorporation of Cd2+ and Ag+ on the structural, morphological and optical properties. The resulting films had a pyramidal structure of single crystals, nanosized particles of nonspecific shape, agglomerated and indistinct grains. ATR-FTIR spectroscopy revealed the interaction between PA 6 and inorganic components, which causes obvious conformational changes in PA 6 chains. The data of X-ray diffraction analysis, depending on the stage of synthesis, showed a mixture of various compounds: Se8, CdSe, Ag2Se and Ag. This may explain the observed optical properties. The optical properties of the composites indicate a shift in the band gap from 4.46 eV for PA 6 to 2.23-1.64 eV upon stepwise insertion of amorphous Se, Cd2+ and Ag+ ions. Eg is conveniently located in the visible region of solar energy, making the obtained nanofilms ideal for solar energy harvesting.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

Abstract: Circuit breakers are affected by multiple lightning strikes after the breaker has been tripped and can break down again, which will reduce the life of the circuit breaker and threaten the stable operation of the power system. Aiming at this problem, the paper obtained the temperature diffusion process of the inrush current process of circuit breaker opening and breaking through the schlieren technique, and combined with the existing image recognition technology to obtain the temperature characteristics of the airflow in the air gap of the contact, and the characteristics of the airflow flow. The results of the study show that the circuit breaker breakdown process generates a shock wave with a velocity approximately equal to the speed of sound under the same conditions. The maximum velocity of the airflow boundary diffusion is about 1/4 of the speed of sound under the same condition, and it decays very fast, reducing to the airflow drift velocity within 10ms after breakdown. The maximum temperature of the thermals is concentrated between 6000 and 8000 K and the temperature change is approximately inversely proportional to the square of time. The research provides the basis for the design of circuit breaker contact structure, opening speed optimization method, interrupter chamber and insulation design optimization.

We successfully fabricated Ag@Cu2O core-shell decorated on reduced graphene oxide (rGO) nanocomposites (ACRN) by a simple and convenient in situ substitution method. The properties of these ACRN with heterostructure layers were characterized by scanning and transmission electron microscopies and absorption spectroscopy. We used p-nitrophenol (4-NP) as a probe molecule to determine the chemical catalytic activity of the ACRN. Upon introduction of rGO, a high electron transfer efficiency was achieved; thus, the catalytic activity was improved significantly. Therefore, the ACRN exhibited significantly improved catalytic activity for the reduction of 4-NP and showed the high application value in the removal of toxic and harmful substances from water. In addition, the fabricated ACRN was used for the reduction of organic dyes and explosive pollutants to generate nontoxic products. Furthermore, the high charge redistribution and transfer among Ag, Cu2O and rGO in the ACRN induced the high catalytic reduction of organic pollutants, indicating the excellent potential of these materials for applications in water pollution treatment.

Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

Fresh Ag nanoparticles (NPs) dispersed on a transparent SiO2 exhibit an intense optical extinction band originating in localized surface plasmon resonance (LSPR) in visible range. The intensity of LSPR band weakened when the Ag NPs was stored in ambient air for two weeks. The rate of the weakening and the LSPR wavelength shift, corresponding to visual chromatic changes, strongly depended on the environment in which Ag NPs were set. The origin of a chromatic change was discussed along with both compositional and morphological changes. In one case, bluish coloring followed by a prompt discoloring was observed for Ag NPs placed near the ventilation fan in our laboratory, resulted from adsorption of large amounts of S and Cl on Ag NP surfaces as well as particle coarsening. Such color changes deduce the presence of significant amounts of S and Cl in the environment. In other case, a remarkably blue-shift of LSPR band was observed for the Ag NPs stored in the desiccator made of stainless steel, originated in the formation of CN and/or HCN compounds and surface roughening. Their color changed from maroon to reddish, suggesting that such molecules were present inside the desiccator.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

The increading emission of carbon dioxide to the atmosphere has urged the scientific community to investigate alternatives to alleviate such emissions being the principal contributor to the greenhouse gas effect. One major alternative is carbon capture and utilisation (CCU) towards the production of value-added chemicals using diverse technologies. This work aims at the study of the catalytic potential of different cobalt-derived nanoparticels for methanol syntheis from carbon dioxide hydrogenation. Thanks to its abundance and cost-efficacy, cobalt can serve as an economical catalyst compared to noble-metal-based catalysts. In this work, we present a systematic comparison among different cobalt and cobalt oxide nanocomposites in terms of their efficiency as catalysts for carbon dioxide hydrogenation to methanol as well as how different supports can enhance their catalytic capacity. The oxygen vacancies in the cerium oxide act as carbon dioxide adsorption and activation sites, which facilitates a higher methanol production yield.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

Using of the organic base tetramethylammonium hydroxides (TMAH) is a viable, cheap and fast route, for the MgZnAl-LDH type materials synthesis by both co-precipitation and mechano-chemical methods. TMAH provided several advantages as smaller quantity of water required in the washing step compared to the use of inorganic alkalis, prevention of LDH contamination with alkali cations, acting as template molecule in texture tailoring along with disadvantages as its presence in small quantities in the resulting layered materials. Regardless the use of organic / inorganic bases and co-precipitation / mechano-chemical methods, zincite stable phase was found in all the synthesized solids. The basicity of catalysts followed the trend: mixed oxides > reconstructed > parent LDH. The memory effect of LDH is supported only by the presence of Mg and Al cations, while Zn remains as zincite stable phase. The catalytic activities for Claisen-Schmidt condensation of benzaldehyde with cyclohexanone provided values higher than 90% after 2h, with a total selectivity in 2,6-dibenzylidenecyclohexanone, while in self-condensation of cyclohexanone no more than 7.29% after 5h. These behaviors depended on catalysts basicity as well as the planar rigidity of the compound.

This work focuses on the support effect on the performances of Co-based catalysts for the acetic acid steam reforming. SBA-15, a well ordered hexagonal mesoporous silica structure, and CeO2 have been selected as the supports, with the impact of chromium addition also being investigated. Better acetic acid steam reforming performances have been recorded for CeO2 compared to SBA-15 supported catalysts and, in particular, the 7Co/CeO2 catalyst showed the highest values of acetic acid conversions with enhanced H2 yields below 480°C, in comparison to the other investigated catalytic formulations. In addition, more pronounced coke depositions and acetone concentrations have been obtained with CeO2 supported catalysts, due to the tendency of ceria to catalyse the ketonization reaction. Chromium addition to Co/SBA-15 catalysts led to an enhancement in the activity towards acetic acid steam reforming, while on CeO2 supported catalysts no improvement in the catalysts activity was observed; however, on both SBA-15 and CeO2 supported catalysts, Cr addition reduced the amount of coke deposited on the catalysts surface.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The cDNA sequences of the common gonadotrophic hormone α-subunit (ag-GTHα) and 13 of the specific follicle-stimulating hormone β-subunit (ag-FSHβ) of the giant Amazonian fish Ara-14 paima gigas, have been previously isolated by our research group. A synthesis of ag-FSH in HEK293 15 cells and its purification and preliminary characterization were also carried out. In the present work, 16 ag-FSH was obtained and purified from the same host cells and an extensive physical chemical 17 characterization was performed via RP-HPLC, HPSEC and MALDI-TOF-MS. Ag-FSH, when com-18 pared to human FSH (hFSH), showed a higher hydrophobicity by RP-HPLC and a higher molecular 19 mass (MM) via HPSEC. The same higher MM was also confirmed via MALDI-TOF-MS: 35,353 Da 20 for ag-FSH against 31,969 Da for hFSH. Its immunological activity was also confirmed via an hFSH 21 ELISA, in comparison with the highly purified pituitary preparation of hFSH-AFP7298A, from the 22 National Hormone and Pituitary Program (NHPP-USA). Finally, an in-vitro bioassay, based on the 23 stimulated release of 11-ketotestosterone (11-KT) from immature A. gigas testis, quantified its bio-24 logical activity in comparison with human chorionic gonadotropin (hCG) and with the WHO Inter-25 national Standard of recombinant hFSH (NIBSC-08/282) This suggests that injections of ag-FSH in 26 A. gigas and ag-FSH cDNA Gene Therapy applications should improve the reproductive functions 27 of this threatened species.

In this work, pure TiO₂ and binary nanocomposites of Fe₃O₄/TiO₂ and Ag/TiO₂ were synthesized in order to improve photocatalytic performance of these samples for degradation of 2, 4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, SEM/EDX, and elemental mapping were employed to reveal the crystal structure, morphology and property of the nanocomposites. XRD data demonstrated that the prepared samples are purely in TiO₂ anatase phase and cubic spinel Fe₃O₄ exist in the synthesized nanocomposite. We calculated the TiO₂ crystal size from XRD patterns, in the range of 8.35-11.09 nm. The presence of Ag, Fe, O, and Ti atoms in the synthesized nanocomposites was confirmed by SEM/EDX. We obtained 30.43, 32.02 and 42.40 % degradation of 2, 4-DCP (100 ml 2, 4-DCP 40 ppm and 0.01 g catalyst) for pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively, after 180 min of irradiation under visible light. Similar conditions were employed for 2, 4-DCP degradation under UV irradiation, we obtained 53.05, 51.00 and 71.50 % degradation of 2, 4-DCP pure TiO₂, Fe₃O₄/TiO₂ and Ag/TiO₂, respectively. Thus, the synthesized binary nanocomposites exhibited higher photocatalytic activity compared to pure TiO₂ under visible light.

Mercury (Hg) is a toxic element impacting on biological systems and ecosystems. Because the toxicity of Hg species is highly dependent on concentration levels and chemical forms, sensitive identification of chemical forms for Hg, i.e., Hg speciation, is of major significance in providing meaningful information about the source of Hg exposure. In this study, a microfluidic-based device made of high clarity poly(methyl methacrylate) (PMMA) was fabricated. Then titanium dioxide nanoparticles (nano-TiO2) were attached to the treated channel interior with the aid of poly(diallyldimethylammonium chloride) (PDADMAC). After coupling the nano-TiO2-coated microfluidic-based photocatalyst-assisted reduction device (the nano-TiO2-coated microfluid-ic-based PCARD) with high-performance liquid chromatography (HPLC) and inductively coupled plasma-mass spectrometry (ICP-MS), a selective and sensitive hyphenated system for Hg specia-tion was established. Validation procedures demonstrated that the method could be satisfactorily applied to the determination of mercuric ion (Hg2+) and methylmercury ion (CH3Hg+) in both human urine and water samples. Remarkably, the zeta potential measured clearly indicated the PDADMAC-capped nano-TiO2 with predominance of positive charges indeed provided steady force for firm attachment to the negatively charged device channel. The cause for the durability of the nano-TiO2-coated microfluidic-based PCARD was clarified thus.

ERI and SSZ-13 were subjected to post-synthetic treatments (depending on the zeolite topology) to create micro-/mesoporous materials. The results of NH3-SCR-DeNOx show that the applied treatments improved the catalytic activity of the Cu-containing ERI-based materials; however, the NO conversion does not vary for the different materials treated with NaOH or NaOH/HNO3. For the micro-/mesoporous Cu-containing SSZ-13, a lower NO conversion in NH3-SCR-DeNOx is observed. Thus, our findings challenge the current paradigm of enhanced activity of micro-/mesoporous catalysts in NH3-SCR-DeNOx. The modification of the supports results in the presence of different amounts and kinds of copper species (especially isolated Cu2+ and aggregated Cu species) in the case of ERI- and SSZ-13-based samples. The present copper species further differentiate the formation of reactive reaction intermediates. Our studies approved that besides the -2,2-peroxo dicopper(II) complexes (verified by in situ DR UV-Vis spectroscopy), also copper nitrates (evidenced by in situ FT-IR spectroscopy) act as reactive intermediates in these catalytic systems.

The removal of sulfur from fossil fuels is one of the most important processes in modern refineries. It is accomplished via hydrodesulfurization (HDS) of the sulfur organic compounds in presence of heterogeneous catalysts. In the current work, heterogeneous catalysts containing cobalt and mo-lybdenum supported on mesoporous materials type SBA-15 and AlSBA-15 were synthesized for application in the HDS reactions of thiophene in n-heptane stream. The mesoporous materials were synthesized by hydrothermal method starting from TEOS, pseudobohemite, hydrochloric ac-id and water. Pluronic P123 was used as template. The best calcination conditions for removal of the organic template were optimized by thermogravimetry analysis (TG/DTG). The calcined SBA-15 and AlSBA-15 supports were submitted to co-impregnation with solutions of cobalt nitrate and ammonium heptamolybdate, aiming the production of 15% in mass of metal loading with atomic ratio of [Co/(Co+Mo)]=0.45. The obtained materials were dried and calcined for obtaining the mesoporous catalysts in the form of CoMo/SBA-15 and CoMo/AlSBA-15. The catalysts were char-acterized by XRD, TG/DTG, SEM and nitrogen adsorption. From XRD analysis, it was verified that after decomposition of the cobalt and molybdenun salts, were formed MoO3, Co3O4 and Co-MoO4 oxides on the supports, being attributed to these chemical species the activity for the HDS reactions. The activity of the obtained catalysts was evaluated in a continuously flowing tubular fixed-bed microreactor coupled on-line to a gas chromatograph, using n-heptane stream contain-ing 12070 ppm of thiophene (ca. 5100 ppm of sulfur) as a model compound. From the catalytic tests it was verified that the synthesized catalysts presented good activity for the reaction, and the main obtained products were cis- and trans-2-butene, 1-butene, n-butane and low amounts of iso-butane. The presence of 1,3-butadiene and tetrahydrothiophene (THT) were not detected. A mechanism of the primary and secondary reactions and subsequent formation of the olefins and paraffins, in the CoMo/SBA-15 and CoMo/AlSBA-15 mesoporous catalysts were proposed, con-sidering steps of desulfurization, hydrogenation, dehydrogenation, THT decyclization and isomerization.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

This study considers the features of the chemical composition, internal structure, and oscillatory zoning of sulfides, sulfosalts and sulfates in the epithermal high-intermediate sulfidation type Au-Ag-Te Emmy deposit (Khabarovsk Territory), Russia. In this deposit the most widespread sulfide is pyrite occurring in two generations: pre-ore pure pyrite (I) with cubic crystal habit and dimensions from 20 μm to 0.5 mm from the early barren pre-ore hydrothermal stage, and pyrite (II) of the ore stage, which is represented by (a) colloform aggregates (IIa) formed as a result of rapid precipitation from the solution, and (b) crystalline pyrite (IIb), which is precipitated due to continuous decrease in temperature. Both pyrite (II) morphological varieties contain copper (0.06-6.03 wt.%). The crystalline variety of pyrite is associated with goldfieldite, hemusite and kawazulite which were deposited during the early mineralizing event in the deposit.

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

Nitrogen oxides (NOx), pivotal atmospheric pollutants, significantly imperil the environment and human health. The CH4-SCR process, leveraging the abundant and accessible methane (CH4), emerges as a promising avenue for NOx abatement. Previous studies have demonstrated that zeolite support with twelve-membered ring (12-MR) and five-membered ring (5-MR) structures are susceptible to framework collapse in the presence of water, leading to catalyst deactivation. Consequently, there is a necessity to explore novel zeolites with enhanced hydrothermal stability for application in CH4-SCR processes. This research introduced for the first time an investigation into a novel In-H-SSZ-39 catalyst, synthesized via ion exchange and meticulously optimized for preparation conditions, including calcination temperature, In ions concentraiton, and reaction conditions, including CH4/NO ratio, O2 concentration, water vapor content, and Gas hourly space velocity (GHSV). Notably, the In/H-SSZ-39 catalyst achieved superior performance of 42.1% at 605 °C, with a calcination temperature of 500 °C and an In ion concentration of 0.066 M, under CH4/NO ratio of 1.5:1, 10% O2, and GHSV of 21000 h-1. In addition, the catalytic performance was influenced by the concentration of water vapor and the GHSV value.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

Electrochemical Promotion was used to modify the activity and selectivity of a Rh catalyst-electrode in the CO2 hydrogenation reaction. The experiments were carried out in a temperature range of 350-430οC at ambient pressure and at different CO2 to H2 gas feeding ratios (1:2 to 4:1). The only reaction products observed were CO and CH4, both under open and closed-circuit conditions. The CH4 formation rate was found to increase with both positive and negative potential or current application. The CO formation rate followed the opposite trend. The selectivity to CH4 increased under high values of hydrogen partial pressure and decreased at high pressures of CO2. The results demonstrate how Electrochemical Promotion can be used to finely tune activity and selectivity for a reaction of high technical and environmental importance.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Background: Mounting evidence supports the role of the endocannabinoid system in neurophysiology, includ-ing blood-brain barrier (BBB) function. Recent work has demonstrated that activation of endocannabinoid re-ceptors can mitigate insults to the BBB during neurological disorders, like traumatic brain injury, cortical spreading depression and stroke. As alterations to the BBB are associated with worsening clinical outcomes in these conditions, studies herein sought to examine the impact of endocannabinoid depletion on BBB integrity. Methods: Barrier integrity was investigated in vitro via bEnd.3 cell monolayers to assess endocannabinoid syn-thesis, barrier function, calcium influx, junctional protein expression, and proteome-wide changes. Results: In-hibition of 2-AG synthesis using DAGLα inhibition and siRNA inhibition of DAGLα led to loss of barrier in-tegrity via altered expression of VE-cadherin, which could be partially rescued by exogenous application of 2-AG. Moreover, the deleterious effects of DAGLα inhibition on BBB integrity showed both calcium and PKC (protein kinase C)-dependency. Conclusions: These data indicate that disruption of 2-AG homeostasis in brain endothelial cells, in the absence of insult, is sufficient to disrupt BBB integrity thus supporting the role of the endocannabinoid system in neurovascular disorders.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Worldwide emission standards are now required to cover engine operation under extreme ambient conditions, which affect the raw emissions and the efficiency of the exhaust aftertreatment systems. These regulations also target new combustion technologies for decarbonization, such as neat hydrogen (H2) combustion or dual-fuel strategies, which involve a challenge to the analysis of exhaust aftertreatment systems requirements and performance. This work addresses the impact of high altitude and low ambient temperature conditions on the reactivity of an oxidation catalyst in the presence of H2. A reaction mechanism is proposed to cover the main conversion paths of CO, HC, and H2, including the formation and consumption of high-energy surface reaction intermediates. The mechanism has been implemented into a faster-than-real-time reduced-order model for multi-layer washcoat honeycomb catalytic converters. The model was utilized to investigate the effect of H2 concentration on the reactivity of CO and HC within the catalyst under various operating and ambient conditions. By applying the model and examining the selectivity towards different reaction pathways in the presence H2, insights into surface intermediates and reactivity across different cross-sections of the monolith were obtained. This analysis discusses the underlying causes of reactivity changes promoted by H2 and its relative importance as a function of driving boundary conditions.