A friction loss model for brake testing platform is constructed to revise the braking force test results, which can largely improve the accuracy of automotive brake performance testing. Specifically, the influence of tire pressure, vehicle axle load, placement angle and vehicle speed on the friction loss is tested and analyzed on a wheelbase adjustable automotive anti-force brake testing platform. The friction loss model for the platform is constructed based on the defined relative slip and placement angle, which is validated through actual tests on four types of vehicles. The results showed that the maximum relative error between the values of the model calculated simulation and the measured was 2.2%, indicating the friction loss model is valid and can provide a basis for revising the braking force of automotive brake. Meanwhile, the maximum braking force increases from 3982 N to 4772 N, increased by 19.8%, when the placement angle increased from 36.9° to 47.0°. Accordingly, in order to improve the accuracy of detection results of the automotive anti-force rolling brake testing platform, the friction loss caused by the change in the placement angle should be revised, and then braking rate of the vehicle should be judged according to GB 7258-2017 and GB 38900-2020.

The manual muscle test (MMT) is a flexible diagnostic tool, which is used in many disciplines, applied in several ways. The main problem is the subjectivity of the test. The MMT in the version of a “break test” depends on the tester’s force rise and the patient’s ability to resist the applied force. As a first step, the investigation of the reproducibility of the testers’ force profiles is required for valid application. The study examined the force profiles of n=29 testers (n=9 experiences (Exp), n=8 little experienced (LitExp), n =12 beginners (Beg)). The testers performed 10 MMTs according to the test of hip flexors, but against a fixed leg to exclude the patient’s reaction. A handheld device recorded the temporal course of the applied force. The results show significant differences between Exp and Beg concerning the starting force (padj=0.029), the ratio of starting to maximum force (padj=0.005) and the normalized mean Euclidean distances between the 10 trials (padj=0.015). The slope is significantly higher in Exp vs. LitExp (p=0.006) and Beg (p=0.005). The results also indicate that experienced testers show inter-tester differences and partly even a low intra-tester reproducibility. That highlights the necessity of an objective MMT-assessment. Furthermore, an agreement on a standardized force profile is required – a suggestion is given.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

Lipofuscin is indigestible garbage that accumulates in the autophagic vesicles and cytosol of post-mitotic cells with age. Drs. Brunk and Terman postulated that lipofuscin accumulation is the main or at least a major driving factor in aging. They even posited that the evolution of memory is the reason why we get lipofuscin at all, as stable synaptic connections must be maintained over time, meaning that the somas of neurons must also remain in the same locale. In other words, they cannot dilute out their garbage over time through cell division. Mechanistically, their position certainly makes sense given that rendering a large percentage of a post-mitotic cell’s lysosomes useless must almost certainly negatively affect that cell and the surrounding microenvironment. It may be the case that lipofuscin accumulation is the main issue with regard to current age-related disease. Degradation in situ may be an insurmountable task currently. However, a method of systemic lipofuscin removal is discussed herein.

The Attentional Networks Test for Interactions and Vigilance–executive and arousal components (ANTI-Vea) is a computerized task of 32 min duration in the standard format. The task simultaneously assesses the main effects and interactions of the three attentional networks (i.e., phasic alertness, orienting, and executive control) and two dissociated components of vigilance with reasonable reliability (executive and arousal vigilance). We present this free and publicly accessible resource (ANTI-Vea-UGR; https://anti-vea.ugr.es/) developed to easily run, collect, and analyze data with the ANTI-Vea (or its subtasks measuring some attentional and/or vigilance components embedded in the ANTI-Vea). Available in six different languages, the platform allows for adaptation of stimuli timing and procedure to facilitate data collection from different populations (e.g., clinical patients, children). Collected data can be freely downloaded and easily analyzed with the provided scripts and tools, including a Shiny app. We discuss previous evidence supporting that attention and vigilance components can be assessed in typical lab conditions as well as online and outside the laboratory. We hope this tutorial will help researchers interested in measuring attention and vigilance with a tool useful to collect data from large sample sizes and easy to use in applied contexts.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

In order to reduce the large damage caused by train derailment, protective facilities of various shapes and conditions can be installed on railroad tracks. These protective facilities are referred to as derailment containment provisions (DCPs) and three different types are used worldwide. However, there are no clear standards for DCPs design such as installation location, size, and design load, and performance verification of DCPs installed in the actual railway field is not sufficiently performed. In this paper, the functionality of DCPs is analyzed through the full-scale derailment test. In order to propose a method for estimating the collision load acting on the DCP type I after derailment, the experimental results and simulation results are compared. The function of DCP type I according to the change of the vehicle's center of gravity is identified through comparative analysis of the post derailment behavior.

(1) Background: Hepatitis C virus (HCV) screening mostly uses a one-assay anti-HCV testing approach, which has a higher probability of false-positive results in populations with low HCV prevalence. (2) Methods: In this investigation, 17,926 participants, were screened for HCV, and the reactives were tested using a two-assay anti-HCV approach: Elecsys ElectroChemiLuminescence (ECL) and a ChemiLuminescence ImmunoAssay (CLIA), respectively. A recombinant immunoblot assay (RIBA) was performed to confirm anti-HCV positivity. Statistical analysis was performed. (3) Results: A total of 350 specimens resulted reactive in the ECL screening, of which CLIA retesting showed that 292 (83.4%) were anti-HCV reactive (283 positive, 9 indeterminate, none negative by RIBA), but 58 (16.6%) were not anti-HCV reactive (15 positive, 12 indeterminate, 31 negative by RIBA). The two-assay strategy significantly improved the positive predictive value (PPV: 95.00%) with χ2: 7.59(p<0.01) then the PPV assessed by one assay (PPV: 90.6%) with χ2: 34.51 (p< 0.001). The ROC curve defined a sensibility and specificity for the dual approach of: 99.66% and 100.00%. (4) Conclusions: Compared with a one-assay testing strategy, the two-assay testing strategy may significantly reduce false positives in anti-HCV testing and identify inactive HCV infection in low seroprevalence populations.

Herbal cosmetics are cosmetics derived from plants. One example is bakuchiol. Bakuchiol is a meroterpene phenol from the seeds of the Psoralea corylifolia plant. Bakuchiol can be derived from Psoralea grandulosa, Pimelea drupaceae, Ulmus davidiana, Otholobium pubescens, and Piper longum. Bakuchiol has antioxidant, anti-inflammatory, and anti-aging activities such as retinol. Bakuchiol will replace retinol with much better safety. Bakuchiol and retinoids share similar cellular pathways, such as the regulation of retinoic acid, the expression of collagen, and extracellular matrix synthesis enzymes. Bakuchiol has many benefits for the skin, so cosmetics and skin therapy can use bakuchiol. This review aims to provide information about the activity of bakuchiol, which has benefits for facial skin, so that this review can be a reference in making cosmetics containing bakuchiol. Bakuchiol has many benefits for skincare such as anti-aging, anti-hyperpigmentation, anti-oxidant, anti-inflammatory, anti-acne, and anti-melanogenesis. Products containing bakuchiol on the market are cleansers, serum, nanoemulsion, and cream.

Background: The fascial system provides an environment that enables all body systems to operate in an integrated manner and is capable of modifying its tensional state in response to the stress applied to it. Recent in vitro, animal and cadaveric studies have shown that “myofascial force transfer” (MFT) has the potential to play a major role in musculoskeletal function and dysfunction.Objective: Human evidence for the existence of invivo MFT is scarce. This scoping review attempts to gather and analyse the available evidence of the in-vivo human MFT studies in order to sustain and facilitate further research and evidence based practice in this field.Methods: A search of most major databases was conducted with relevant keywords that yielded 238 articles as of August 2020. A qualitative analysis of the studies was conducted after rating it with Oxford’s Center for Evidence –based Medicine (CEBM) scale.Result: Nineteen studies ranging from randomized controlled trials to case studies covering 540 patients were included in this review. The analysed studies were highly heterogeneous and of lower methodological quality meddling with the quantitative analysis. Ten studies are confirming a ‘most likely’ existence of MFT, eight studies confirming it as ‘likely’ and one study couldn’t confirm any MFT existence in this review.Conclusion: Findings from in vivo human studies supports the animal and cadaveric studies claiming the existence of MFT which need to be corroborated by the future high quality studies. Forthcoming studies on MFT may give answers and solutions to many of the human musculoskeletal mysteries or dysfunctions.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

The Casimir–Lifshitz friction force and the heating rates of two metal plates with a narrow vacuum gap between them during nonrelativistic motion of one of them are calculated analytically and numerically within the framework of fluctuation electrodynamics. Changes in material properties are taken into account using the Bloch-Grüneisen and modified Bloch-Grüneisen (with finite residual resistance) resistivity models within the Drude approximation. It is shown that identical plates with the same initial temperature have the same heating rate, determined by the power of the friction force, and the possibility of measuring the friction force from the heating kinetics of nonmagnetic metal plates with temperatures of 1–10 K is substantiated.

The growing worldwide cancer incidence, coupled to the increasing occurrence of multidrug cancer resistance, requires a continuous effort towards the identification of new leads for cancer management. In this work, two C-scorpionate complexes, [FeCl2(κ3-Tpm)] (1) and [Co(κ3-TpmOH)2] (2), (Tpm = hydrotris(pyrazol-1-yl)methane and TpmOH = 2,2,2-tris(pyrazol-1-yl)ethanol), are studied as potential scaffolds for future anti-cancer drug development. Their cytotoxicity and cell migration inhibitory activity are analyzed, and an untargeted metabolomics approach is em-ployed to elucidate the biological processes significantly affected by these two complexes, using two tumoral cell lines (B16 and HCT116) and a non-tumoral cell line (HaCaT). While [FeCl2(κ3-Tpm)] did not display a significant cytotoxicity, [Co(κ3-TpmOH)2] was particularly cy-totoxic against the B16 cell line. While [Co(κ3-TpmOH)2] significantly inhibited cell migration in all tested cell lines, [FeCl2(κ3-Tpm)] displayed a mixed activity. From a metabolomics perspective, exposure to [FeCl2(κ3-Tpm)] is associated with changes in various metabolic pathways involving tyrosine, where iron-dependent enzymes are particularly relevant. On the other hand, [Co(κ3-TpmOH)2] is associated with dysregulation of cell adhesion and membrane structural pathways, suggesting its antiproliferative and anti-migration properties can be due to changes in the overall cellular adhesion mechanisms.

Encephalitis is a condition with a variety of etiologies, clinical presentations and degrees of severity. The causes of these disorders include both neuroinfections and autoimmune diseases in which host antibodies are pathologically directed against self antigens. In autoimmune encephalitis, autoantibodies are expressed in the central nervous system. The incidence of this disease is approximately 4% of all reported cases of encephalitis. Autoimmune encephalitis can be induced by antibodies against neuronal surface antigens such as N-methyl-D-aspartate-activated glutamate receptors (NMDAR), ⍺-amino-3-hydroxy-5-methyl-4-isoxazole propionate receptors (AMPAR) or gangliosides GQ1b, DPPX, CASPR2, LGI1, as well as by antibodies against neuronal intracellular antigens. The paper presents a number of both mental and neurological symptoms of autoimmune encephalitis. Moreover, the coexistence of psychoses, neoplastic diseases and the methods of diagnosing autoimmune encephalitis are discussed. Attention was also drawn to the fact that early diagnosis, as well as early initiation of targeted treatment, increases the chance of a successful course of the therapeutic process.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

Work reviews the new isolated isolated cembranoid diterpene derivatives from species belonging to the family Alcyoniidae, which comprises the genera Sarcophyton, Sinularia, and Lobophytum as well as their biological properties, during 2016–2017. The compilation permitted to conclude that much more new cembranoid diterpenes were found in the soft corals of the genus Sarcophyton sp. (33 new compounds) than in those belonging to the genera Lobophytum (17) or Sinularia (8). Several methods have been used for identifying these new compounds, after extraction with organic solvents and fractionation. The fractions obtained, in some cases, were followed by TLC, and again subjected to chromatographic procedures, including semi-preparative HPLC. Beyond the chemical composition, the biological properties were also evaluated, namely anti-microbial against several Gram-positive and Gram-negative bacteria and fungi, anti-inflammatory and anti-tumoral against several types of cancer cells. Although the biological activities detected in almost all samples, they were not outstanding ones.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

Curcumin is the main secondary metabolites of Curcuma longa and other Curcuma spp, and has been reported to have some potential in preventing and treating some physiological disorders. This study investigated the effect curcumin in inhibiting high-fat diet and streptozotocin (STZ)-induced hyperglycemia and hyperlipidemia in rats. Twenty-six male Sprague-Dawley (SD) rats (170-190 g) were randomly divided into a standard food pellet diet group (Control group), a high-fat diet and streptozotocin group (HF+STZ group), and a high-fat diet combined with curcumin and STZ group (HF+ Cur +STZ group). Compared with the HF+STZ group, the HF+Cur+STZ group exhibited significantly reduced fasting blood glucose (FBG), total cholesterol (TC), triglyceride (TG), low-density lipoprotein cholesterol (LDL-C), high-density lipoprotein cholesterol (HDL-C), alanine aminotransferase (AST) and aspartate transaminase (ALT) levels, and liver coefficients; in the livers of these rats, the expression of malondialdehyde (MDA) and Bax was downregulated, whereas that of superoxide dismutase (SOD) and Bcl-2 was upregulated. Moreover, the liver histology of these rats was improved and resembled that of the control rats. These results suggest that curcumin prevents high-fat diet and STZ-induced hyperglycemia and hyperlipidemia, mainly via anti-oxidant and anti-apoptotic mechanisms in the liver.

Atomic force microscopes are used, beside their principal function as surface imaging tools, in surface manipulation and measurement of interfacial properties. In particular, they can be modified to measure lateral friction forces that occur during the sliding of the tip against the underlying substrate. However, the shape, size, and deformation of the tips profoundly affect the measurements in a manner that is difficult to predict. In this work, we investigate the contribution of these effect to the magnitude of the lateral forces during sliding. The surface substrate is chosen to be few-layer AB-stacked graphene surface whereas the tip is initially constructed from face-centered cubic gold. In order to separate the effect of deformation from shape, rigid tips of three different shapes were considered first, namely a cone, a pyramid and a hemisphere. The shape was seen to dictate all aspects of the interface during sliding, from temperature dependence to stick-slip behavior. Deformation was investigated next by comparing a rigid hemispherical tip to one of identical shape and size but with all but the top three layers of atoms free to move. The deformation, as also verified by an indentation analysis, occurs by means of the lower layers collapsing on the upper ones, thereby increasing the contact area. This collapse mitigates the friction force and decreases it with respect to the rigid tip for the same vertical distance. Finally, the size effect is studied by means of calculating the friction forces for a much larger hemispherical tip whose atoms are free to move. In this case, the deformation is found to be much smaller but the stick-slip behavior is much more clearly seen.

Temperature dependent entropic force acting between the straight direct current I and the linear system (string with length of L) of N elementary non-interacting magnets/spins μ is reported. The system of elementary magnets is supposed to be in the thermal equilibrium with the infinite thermal bath T. The entropic force at large distance from the current is given by Fmagnen=Nμ02μ2I24π2kBTr3 , where r is the distance between the edge of the string and the current I, and kB is the Boltzmann constant; (r≫L is adopted). The entropic magnetic force is the repulsion force. The entropic magnetic force scales as Fmagnen~1T , which is unusual for entropic forces. The effect of “entropic pressure” is predicted for the situation when the source of the magnetic field is embedded into the continuous media, comprising elementary magnets/spins.

Inotodiol, a lanostane-type triterpenoid, and many phytochemicals from Chaga mushroom have been investigated for various allergic diseases. However, antiaging and anti-inflammatory activities of inotodiol under different types of oxidative stress and impact of inotodiol on collagen and hyaluronan synthesis are not sufficiently studied. Lanostane triterpenoids-rich concentrate, which contained 10% inotodiol as major (the inotodiol concentrate), was prepared from Chaga and compared with pure inotodiol in terms of anti-inflammatory activities on a human keratinocyte cell line, HaCaT cells, under various stimulation such as stimulation with ultraviolet (UV) B or tumor necrosis factor (TNF)-α. In stimulation with TNF-α, interleukin (IL)-1β, IL-6, and IL-8 genes were significantly repressed by 0.44~4.0 μg/mL of pure inotodiol. UVB irradiation induced overexpressions of pro-inflammatory cytokines, but those genes were significantly suppressed by pure inotodiol or inotodiol concentrate. Moreover, pure inotodiol/inotodiol concentrate could also modulate synthesis of collagen and hyaluronic acid by controlling COL1A2 and HAS2/3 expression, which implies a crucial role of pure inotodiol/inotodiol concentrate in prevention of skin aging. These results enlighten anti-inflammatory and anti-aging effect of pure inotodiol/inotodiol concentrate, and it is highly conceivable that pure inotodiol and inotodiol concentrate could be promising natural bioactive substances to be incorporated in therapeutic and beautifying applications.

Antibiotic failure is one of the most worrying health problems worldwide. Nowadays we are facing an international crisis where several issues are involved: new antibiotics are not being discovered any longer, resistance mechanisms become spread in nearly every clinical isolate of bacteria and the appearance of recurrent infections caused by persistent bacteria complicates the overcoming of infections. In this context, it has been explored new anti-infectious strategies against MDR and persistent bacteria as well as the rescue of FDA-approved compounds (drug repurposing). Among the highlighted new anti-infectious strategies we find anti-microbial peptides, anti-virulence compounds, phage therapy and new molecules. On the other hand, as drugs of repurposing that have been described, we have anti-inflammatory compounds, anti-psychotics, anti-helmintic drugs, anti-cancerous and statins.

Counterfeiting and theft have always been problems that incur high costs and results in considerable losses for the international markets. In this research paper, we will address the issue of counterfeiting while using RFID technology in retailer systems or other industries by presenting a new anti-counterfeiting and anti-theft system for the retailer market. This system will address the two above mentioned issues and provide a solution that can save the retailer systems millions of dollars yearly. This proposed system will achieve the objective of preventing or minimising the counterfeiting and theft of tagged products. At the same time, it will provide a strong indication for suspiciously sold or obtained items. Furthermore, we conducted a security analysis to prove the correctness of our protocol on the basis of the strand spaces.

This paper proposes a multi-terminal adaptive collaborative operation method to solve the problem of unstable internal force tracking in clamping and handling unknown objects by multi-terminal robots. In the proposed method, the internal command force changes the complex internal force control problem into an internal force tracking problem from multi-slave to master. Moreover, we develop an algorithm for multi-slave setups to estimate object stiffness and motion uncertainty in the direction of the internal command force according to Lyapunov theory. Finally, the impedance control generates a reference trajectory for the multi-slave to maintain the desired internal force and track the master’s motion. Several experiments are conducted on a self-made robot equipped. The experimental results show that the oscillation amplitude of each slave end is less than 1 mm, the directional oscillation amplitude is less than 1 degree during the tracking of the desired commanded internal force. For objects with low stiffness, the error of the commanded internal force is less than 1 N (6%) per slave. The error in tracking the commanded internal force for objects with high stiffness is less than 2 N (8%). The results prove the feasibility and effectiveness of the proposed method.

The translocator protein (TSPO) is a transmembrane protein present in the three domains of life. Its functional quaternary structure consists of one or more subunits. In mouse, the dimer-to-monomer equilibrium is shifted in vitro towards the monomer by adding cholesterol, a natural component of mammalian membranes. Here, we present a coarse-grained molecular dynamics study on the mouse protein in the presence of a physiological content and of an excess of cholesterol. The latter turns out to weaken the interfaces of the dimer by clusterizing mostly at the inter-monomeric space and pushing the contact residues apart. It also increases the compactness and the rigidity of the monomer. These two factors might play a role for the experimentally observed incremented stability of the monomeric form with increased content of cholesterol. Comparison with simulations on bacterial proteins suggests that the effect of cholesterol is much less pronounced for the latter than for the mouse protein.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

We present a Quantum Space Model (QSM) of cosmic evolution based on the theory that space consists of energy quanta which participates in the evolution of the universe. It shows that Dark Energy is the energy of space which causes its accelerating expansion. We used the Friedmann equations to trace the history of the cosmos from a time before the Big Bang to its ultimate end. The universe started from a quantum size volume of space with high energy density.Quantum fluctuations triggered the release of energy in a Big Bang at very high temperature and pressure. It then expanded and cooled undergoing phase transitions to radiation, fundamental particles, and matter. Matter grew into galaxies, and was further consolidated by gravity into Dark Energy Stars/Black Holes, ending in a Big Crunch at about 1.380 trillion years, thus bringing the universe back to its initial state. It can stay in a Deep Feeeze inside a Black Hole and through fluctuations or other mechanism may start a new cycle in its life with a new Bang. If the Law of Conservation of Energy is universal, then the cosmos is eternal. Space and energy are equivalent just as matter and energy are. This is well founded in Planck’s energy equation. They are the two most fundamental quantities in the universe that govern cosmic evolution. The two principal long range forces are the gravitational force and the space force.The latter could be the fifth force in the universe. They may provide the clockwork mechanism that operates our eternal cyclic universe.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Many studies discuss carbon-based materials because of the versatility of its element. They include different opinions for scientific problems and discuss fairly at convincing and compelling levels within the scope and application. A gas-state carbon atom converts into various states depending on its conditions of processing. The electron transfer mechanism in the gas-state carbon atom is responsible to convert it into various states, namely, graphite, nanotube, fullerene, diamond, lonsdaleite and graphene. The shape of ‘energy trajectory’ enables transferring electrons from the left- and right-sides of an atom is like a parabola. That ‘energy trajectory’ is linked to states (filled state and suitable nearby unfilled state) where force-exertion along the poles of transferring electrons is remained balance. So, the mechanism of originating different states of a gas-state carbon atom is under the involvement of energy first. This is not the case for atoms executing confined inter-state electron-dynamics as the force is involved first. Graphite-, nanotube- and fullerene-state atoms ‘partially evolve partially develop’ (form) their structures. These possess one-dimensional, two-dimensional and four-dimensional ordering of atoms, respectively. Their structural formation also comprises ‘energy curve’ having a shape-like parabola. Transferring suitable filled state electron to suitable nearby unfilled state is under a balance force exerting along the poles. The graphite structure under only attained-dynamics of atoms can also be formed but in two-dimension. Here, binding energy between graphite-state carbon atoms is for a small difference of exerting forces along their opposite poles. Structural formation in diamond, lonsdaleite and graphene atoms involve energy to gain required infinitesimal displacements of electrons through which they maintain orientationally-controlled exerting forces along dedicated poles. In this study, the growth of diamond is found to be south to east-west (ground) where atoms bound ground to south. Thus, diamond atoms merge for a tetra-electron ground to south topological structure. Lonsdaleite atoms merge for a bi-electron ground to just-south topological structure. The growth of graphene is found to be north to ground where atoms bound ground to north. Thus, graphene atoms merge for a tetra-electron ground to north topological structure. Glassy carbon exhibits layered-topological structure where, tri-layers of gas-, graphite- and lonsdaleite-state atoms successively bind in repetitive order. Nanoscale hardness is also sketched based on different force-energy behaviors of different state carbon atoms. Here, structure evolution in each carbon state atom explores its own science.

Vaccine refusal and hesitancy pose a critical challenge to public health, leading to delays in vaccination and compromising herd immunity. To address this issue, we conducted a comprehensive observational study on the adult Spanish population in 2021. Through an online questionnaire, we explored the sociodemographic and sociocultural factors, beliefs, and opinions of those refusing or holding hesitancy about vaccines, and their vaccination behaviours by vaccine type and sex. Our findings revealed that vaccine refusal rates were relatively low (16.8%), and mainly associated with influenza vaccination (10.3%). Greater refusal of vaccination was observed in over 60 years old, in those expressing hesitancy due to vaccine components and opposing free and compulsory vaccination, unaware that vaccination protects the community and being against consuming cow’s milk and the use of infant formulas for breastfeeding. Vaccine hesitancy was greatest in individuals under 31 years old, women, parents of children under 15 years old, against compulsory vaccination, unaware that vaccination protects the community, with hesitancy due to vaccine costs, and in favour of alternative and complementary treatments. These insights underscore the need for strategies to improve education about vaccination and dispel misconceptions are crucial for effectively reducing vaccine refusal and hesitancy across the population.

Maslinic acid (MA) is a natural triterpene from Olea europaea whose pharmacological functions have been showed. The objective of this study was to examine MA effect on cell viability (by MTT assay), reactive oxygen species (ROS levels, by flow cytometry) and key anti-oxidant enzyme activities (by spectrophotometry) in murine skin melanoma (B16F10) cells compared to healthy cells (A10). MA induced cytotoxic effects in cancer cells (IC50 42 µM) whereas no effect was found in A10 cells treated with MA (up to 210 µM). In order to produce a stress situation in cells, 0.15 mM of H2O2 were added. Under stressful conditions, MA protected both cell lines against oxidative damage, decreasing intracellular ROS, being higher in B16F10 than in A10 cells. The treatment with H2O2 and without MA produced different responses in anti-oxidant enzymes activities depending on cell line. In A10 cells, all enzymes were up-regulated, but in B16F10 cells only superoxide dismutase, glutathione S-transferase and glutathione peroxidase increased their activities. MA restored the enzyme activities to similar levels than control group in both cell lines, highlighting that in A10 cells the highest MA doses induced values lower than control. Overall, these findings demonstrate the great anti-oxidant capacity of MA.

STRAS (Single access Transluminal Robotic Assistant for Surgeons) is a flexible robotic system based on the Anubis® platform of Karl Storz for application to intra-luminal surgical procedures. It consists of three cable-driven systems, one endoscope serving as guide and two inserted instruments. The flexible and bendable instruments have three degrees of freedom and can be teleoperated by a single user via two specially designed master interfaces. In this research, a pair of specific sensor gloves, which ergonomically fit to the master handles of the system was designed and the forces applied by one expert and one novice user during system-specific task execution in a simulator task (4-step-pick-and-drop) were compared. The results show that user expertise is not only reflected by shorter task execution times but also, more importantly, by specific differences in handgrip force profiles for specific sensor locations on anatomically relevant parts of the fingers and hand controlling the surgical instruments of the robotic master/slave system.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Immune-mediated necrotizing myopathy (IMNM) is a rare and severe disease that corresponds to a specific entity of idiopathic inflammatory myopathy. Patients with IMNM suffer from proximal muscle weakness, and present high levels of creatine kinase and necrotic myofibers. Anti-Signal Recognition Particle (SRP) and anti-3-hydroxy-3-methylglutaryl-coenzyme A reductase autoantibodies (HMGCR) have recently been identified in two thirds of patients with IMNM and are used as a hallmark of the disease. In this review, we provide a detailed description of these antibodies and the tests used to detect them in the serum of patients. Based on in vitro studies and mouse models of IMNM, we will discuss the role of autoantibodies in the pathogenesis of the disease. Finally, in the light of the latest knowledge, we will conclude with a review of recent therapeutic approaches.

Three new polyketides (penidihydrocitrinins A–C, 1–3) and 14 known compounds (4–17) were isolated from the deep-sea-derived Penicillium citrinum W17. Their structures were elucidated by comprehensive analyses of 1D and 2D NMR, HRESIMS, and ECD calculations. Compounds 1–17 were evaluated for their anti-inflammatory and anti-osteoporotic bioactivities. All isolates exhibited significant inhibitory effects on microglial activation in LPS-stimulated BV-2 cells in a dose-response manner. Notably, compound 14 displayed the strongest effect with the IC50 value of 4.7 µM. Moreover, compounds 6, 7, and 8 not only suppressed osteoclastogenesis, but also promoted osteoblast mineralization.

Green products have excellent potential for discovering and producing new medicinal products. In recent years, there is a growing interest towards the green synthesis of metal nanoparticles, particularly from plants sources. This eco-friendly approach was used in the recent research to biosynthesize zinc oxide nanoparticles (ZnO NPs) from Cissus antractica plant. The present study aims to examine the cell cytotoxicity, cell death, and pathways of apoptosis in lung cancer cells (A549) and inflammation properties treated with biosynthesized ZnO NPs. Additionally, synthe-sized ZnO nanoparticles were characterized using UV–vis spectroscopy, X-ray diffraction (XRD), Transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FT-IR), and Energy-dispersive X-ray spectroscopy (EDS). The XRD and TEM analyses exhibited 31 nm as the size of synthesized nanoparticles, the pure crystal form of ZnO NPs, and the shape of the NPs as nearly spherical and hexagonal quartzite. The MTT assay used for cytotoxicity evaluation de-picted the significant toxic effect of CA-ZnONPs against the A549 lung cancer cells at concentra-tions up to 20 µg/mL than non-cancerous cells. Furthermore, we observed an elevated ROS level in cancer cells. These NPs also demonstrated dose-dependent ability to suppress colony for-mation and cell migration, which increases their potential as a lung cancer treatment. Further-more, The NPs formulation's ability to induce apoptosis in cancer cells was further supported by Hoechst and propidium iodide dye. Further, CA ZnO NPs increased the gene expression of BAX, Cyto-c, Caspase 3 and 9, but decreased the expression of Bcl-2, indicating that the nanoformulation triggered mitochondrial-mediated apoptosis. Besides, this study showed that NPs suppressed in-flammatory responses by subsequently decreasing reactive oxygen species (ROS) generation, downregulating the expression of the pro-inflammatory cytokines TNF-α, iNOS, COX-2, IL-6, IL-8, and NO. Moreover, the study's findings imply that Cissus antractica are a potential source with biosynthesize nanoparticles that can might be further investigated for the progress of an-ti-inflammatory and anti-cancer drugs with further study.

Acemella oleracea is known as toothache plant belongs to the family of Asteraceae. It is treated as a medicinal remedy like tuberculosis, illness, cough, rheumatism, and illness. This study was concentrated on the antioxidant, cytotoxic, antimicrobial & thrombolytic activities of methanol extract of Acmella oleracea leaves using in vitro model. The antioxidant activity was estimated as trolox equivalent antioxidant capacity utilizing the DPPH and reducing power tests. The plant extract was tested for its cytotoxic action using a brine shrimp lethality bioassay, thrombolytic activity using clot disruption, and antibacterial activity using a disc diffusion assay technique against four distinct gram-positive and gram-negative bacteria. IC₅₀ value of standard ascorbic acid for DPPH was 7.8µg/ml and the IC50 of the methanol extract of Acmella oleracea leaves was 198.34µg/ml that was moderate effect at all compare with ascorbic acid. Thrombolytic assay of Streptokinase as a positive control showed 88.49% where the extract shows 18.69% lytic activity shows the assay. In this study, the sample of LC₅₀ results of cytotoxicity assay was 1.431 µg/mL which can be treated as less activity. Moreover, the extracts showed low to moderate antibacterial activity against both gram-negative and gram-positive bacterial stains (zone of inhibition-10-26 mm). Vibrio Mimicus bacteria stains exhibited the highest level of activity, with a range of 23 for the diameter of the growth inhibition zone. The current review shows leaf extracts of Acmella oleracea may be used as a source of antioxidant and thrombolytic activity, as well as a significant source of antibacterial and anticancer substances. Further research is required to evaluate in-vivo the pharmacological activity of Acmella oleracea leaves in order to identify the essential metabolites and potential mechanisms.

Methotrexate (MTX) is a potent drug for the treatment of various diseases globally amidst being a chemotherapeutic and immunosuppressant agent. However, hepatotoxicity induced by MTX could be life-threatening if left untreated. Folate supplementation is concurrently applied to reduce the adverse effects of MTX, albeit efficacy compromise. Therefore, there is the need to understand the process for the prevention and treatment strategies for MTX induced hepatotoxicity (MIH). In recent times, preliminary preclinical and clinical findings indicate the potential of natural phytobioactive compounds for MIH prevention and treatment. This mini review therefore summarizes proposed mechanisms of MIH and recent advances in the prevention and treatment prospects of natural phytobioactive compounds on MIH.

The use of plant extracts in the synthesis of metal nanoparticles is a very attractive approach in the field of green synthesis. To benefit from the potential synergy between the biological activities of the Moringa oleifera leaves extract and metallic bismuth, our study aimed at synthesizing bismuth nanoparticles using a hydroalcoholic extract of M. oleifera leaves as a means of green synthesis that yields nontoxic products and reduces the production of wasteful material. To this end, the M. oleifera leaves extract was treated with a bismuth nitrate pentahydrate solution. A color change from light brown to dark brown indicates the synthesis of bismuth nanoparticles. The total phenolic content in the M. oleifera leaves extract used was 23.0 ± 0.3 mg gallic acid equivalent/g of dried M. oleifera leaves powder. Antioxidant property of MO synthesised bismuth Nanoparticles was evaluated and in line with the extract used in the synthesis of NPs. The physical properties of the synthesized bismuth nanoparticles were characterized using UV-Vis spectrophotometer, FT-IR spectrometer, TEM, SEM, and XRD. The synthesized bismuth nanoparticles have a size in the range of 40.4-57.8 nm with amorphous morphology. Using DPPH and phosphomolybdate assays, our findings revealed that the M. oleifera leaves extract and the synthesized bismuth nanoparticles possess antioxidant properties. Using resazurin microtiter assay, we also demonstrate that the M. oleifera leaves extract and the synthesized bismuth nanoparticles exert potent anti-bacterial activity against Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus and Enterococcus faecalis, similarly to the inhibition exerted by Moringa extract, especially against Enterococcus faecalis (MIC values for the extract: 500, 250, 250, and 250 µg/mL; MIC values for the bismuth nanoparticles: 500, 500, 500, and 250 µg/mL, respectively). Similarly, the M. oleifera leaves extract and the synthesized bismuth nanoparticles display relatively stronger anti-fungal activity against Aspergillus niger, Aspergillus flavus, Candida albicans, and Candida glabrata (MIC values for the extract: 62.5, 62.5, 125, and 250 µg/mL; MIC values for the bismuth nanoparticles: 250, 250, 62.5, and 62.5 µg/mL, respectively). Thus, the hydroalcoholic extract of M. oleifera leaves was successfully used in the synthesis of bismuth nanoparticles, showing a positive antioxidant, anti-bacterial, and anti-fungal activity. Therefore, the synthesized bismuth nanoparticles can potentially be employed in the alleviation of symptoms associated with oxidative stress and in the topic treatment of Candida infections.

The synthesis of metal nanoparticles using plant extracts is a very promising method in green synthesis. The medicinal value of Moringa oleifera leaves and the anti-microbial activity of metallic copper were combined in the present study to synthesize copper nanoparticles having a desirable added-value inorganic material. The use of a hydroalcoholic extract of M. oleifera leaves for the green synthesis of copper nanoparticles is an attractive method as it leads to the production of harmless chemicals and reduces waste. The total phenolic content in the M. oleifera leaves extract was 23.0 ± 0.3 mg gallic acid equivalent/g of dried M. oleifera leaves powder. The M. oleifera leaves extract was treated with a copper sulphate solution. A color change from brown to black indicates the formation of copper nanoparticles. Characterization of the synthesized copper nanoparticles was performed using UV-Vis spectrophotometer, FT-IR spectrometer, TEM, SEM, and XRD. The synthesized copper nanoparticles have an amorphous nature and particle size of 35.8-49.2 nm. We demonstrate that the M. oleifera leaves extract and the synthesized copper nanoparticles display considerable antioxidant activity. Moreover, the M. oleifera leaves extract and the synthesized copper nanoparticles exert potent anti-bacterial activity against Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus, and Enterococcus faecalis (MIC values for the extract: 500, 250, 250, and 250 μg/mL; MIC values for the cooper nanoparticles: 500, 500, 500, and 250 μg/mL, respectively). Similarly, the M. oleifera leaves extract and the synthesized copper nanoparticles exert relatively more potent anti-fungal activity against Aspergillus niger, Aspergillus flavus, Candida albicans, and Candida glabrata (MIC values for the extract: 62.5, 62.5, 125, and 250 μg/mL; MIC values for the cooper nanoparticles: 125, 125, 62.5, and 31.2 μg/mL, respectively). Our study reveals that the green synthesis of copper nanoparticles using a hydroalcoholic extract of M. oleifera leaves was successful. In addition, the synthesized copper nanoparticles can be potentially employed in the treatment of various microbial infections due to their potent antioxidant, anti-bacterial, and anti-fungal activities.

The anti-money laundering (AML) process has failed both in identifying suspicious cases in due time as in assisting the AML analysts in decision making. Starting from a new generic anti-fraud approach, this article presents the main aspects related to the development of a multi-agent system that goes beyond the capture of suspicious transactions, seeking to assist the human expert in the analysis of suspicious behaviour. First, a transactional behavioural profile of clients is obtained in a data mining process. A set of rules, obtained through data mining over a real database, in conjunction with specific rules based on legal aspects and in the expertise of the AML analysts make up the agents' knowledge base. The cases for which the system was unable to suggest a decision are flagged as requiring more detailed analysis. The system analysed 6 months of real transactions and indicated several suspicious profiles, a set of these suspects was investigated by the AML analysts who proved the suspicion of several cases, including some that had not been identified by the systems in execution.

Several vaccines against COVID -19 have been developed and licenced to enhance the immune response against SARS-CoV-2. Similarly, infection with SARS-CoV-2 before vaccination has been shown to provide significant protection against severe infection and hospitalisation. The aim of this study was to investigate the effect of three doses of Sinopharm vaccine and SARS-CoV-2 infection on the specific immune response in 103 volunteers, measuring neutralizing antibodies, anti-S1 IgG, anti-RBD IgM, anti-N IgM, anti-N IgG antibodies and interferon γ. Our results showed that the presence of cardiovascular diseases increased the level of anti-N-IgG antibodies, while endocrinological diseases decreased the level of neutralizing antibodies and anti-N-IgG antibodies, suggesting that these diseases alter the effect of vaccine immunity. In addition, there was a significant decrease in anti-S1 IgG levels 6 months and in anti-N IgG levels 18 months post-infection, while neutralizing antibody and interferon γ levels were constant at 3, 6 and 18 months post-infection. Therefore, our results confirm the importance of hybrid immunity as the strongest and most durable compared to exclusively natural or vaccine-induced immunity. Significant positive correlations were found between humoral and cellular immunity markers: neutralizing antibodies, anti-S1 IgG, anti-N IgG and interferon γ, indicating a unique coordinated response specific to COVID-19.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

This paper is the third application-oriented paper based on the "unified theory of forces" and also addresses the shortcomings of previous research in fully explaining the origin and nature of the weak force. The main conclusions of this paper are as follows: (1) It is argued that neutrinos are generated by the gravitational field, and their generation mechanism is similar to the radiation of photons from electron orbital transitions. Particles undergoing orbital transitions in a gravitational field will emit neutrinos. (2) We rigorously derive the energy formula for neutrinos and demonstrate that the energy formula for neutrinos does not comply with the Planck energy formula. Neutrinos with higher energy have longer wavelengths and are more easily observed in experiments.

Objectives The aim of this study was to measure the magnitude of forces in the joints of the lower limb whilst running barefoot and compare them to the forces generated whilst wearing running shoes with a thick midsole.MethodsTwenty-three volunteers who utilised running as their main sport or a training aid ran as training aid were included in this study. Each volunteer would run down a fourteen-meter-long corridor both barefoot and with running shoes. Forces for joints of the lower limb were collected using a Vicon motion analysis system and force plates. The joint forces for the ankles, knees and hips were taken as the largest joint force experienced during the stance phase and then averaged over five running trials.ResultsThere was significant reduction in the joint forces for the ankles, knees, and hips when barefoot running compared to the shod condition.ConclusionBarefoot running could be utilised to prevent both acute and degenerative injuries of the lower limb.

The model of T4 phage, Lambda phage and Escherichia coli is often used in research on virus-host interactions. This paper reports for the first time the thermodynamic driving force of biosynthesis, catabolism and metabolism for the three organisms, on the M9 medium. Moreover, the influence of activities of nutrients and metabolic products is analyzed. All three organisms were found to have very similar Gibbs energies of metabolism. Moreover, since they share the same catabolism, their Gibbs energies of catabolism are identical. However, Gibbs energies of biosynthesis differ. The calculated thermodynamic properties have been used to explain the coexistence of both bacteria and phages in a dynamic equilibrium in natural ecosystems.

The electric field is enormously more powerful than the gravitational field. However, in our normal experience there is no electric field, the electric force is missing. How is it that when you get to larger and larger scales the gravitational field is extremely important whereas the electric field becomes less and less important [1]? This paper proposes a model to explain why gravitation dominates at a larger scale.

Purposely slow velocity resistance exercise (i.e., 10 s concentric and eccentric phases) is a popular training method, but limits the loads that can be lifted (e.g., <50% 1 RM). This study compared the biomechanical properties of purposely slow velocity (SLOW) and traditional resistance exercise (TRAD) that uses maximal lifting velocities. Healthy resistance-trained men (n=5) performed two testing sessions (barbell squat and bench press) in random-order; a SLOW session (1 set x 10 repetitions at 28% 1 RM, 10 s concentric & eccentric), and a TRAD session (3 x 10 at 70% 1 RM, controlled eccentric and maximal concentric). A force plate and linear position transducer were used to collect kinetic and kinematic data for every repetition of both protocols (α = 0.05). For both exercises, both concentric and eccentric mean force (N) and power (W) for each repetition was greater for TRAD. When the entire training session (squat + bench press) was examined, SLOW exhibited greater time under tension, while TRAD produced greater work (J) and impulse (N·s). Contrary to suggestions in both the lay and scientific literature, purposely slow resistance exercise produced less force, power, and work than traditional velocity resistance exercise.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

Across different cultures around the globe, human beings have historically depended largely on medicinal plants for managing diseases that have hitherto threatened their optimal health, survival, and longevity. Evidently, the health-derived benefits of medicinal plants can be strongly attributed to the presence of secondary metabolites, particularly polyphenols. The health-promoting effects of Sorghum bicolor supplement Jobelyn® (SBSJ) —a unique supplement derived from the leaf sheaths of a West African variety of Sorghum bicolor (L.) Moench—have also been ascribed to its high levels of polyphenols. This review seeks to gather and synthesize findings from various experimental and clinical studies on the health benefits of SBSJ in arthritis, cancer, chronic viral infections, stroke, anaemia, and aging. SBSJ has been reported to contain potent bioactive polyphenolic compounds with polyvalent biological activities, including antioxidant, anti-inflammatory, immunomodulatory, chemopreventive, and neuroprotective activities. Moreover, the probable benefits of SBSJ in chronic viral infections (e.g., HIV/AIDS and COVID-19) have been attributed to its potent anti-inflammatory and immunomodulatory activities. As this supplement is increasingly becoming one of the fastest-selling herbal medicines in Nigeria, there is a need for more robust studies (including clinical trials) in order to replicate and validate the prior insights gleaned from experimental studies.

Hydrogenated water has emerged as a novel approach in the field of health and wellness. It is be-lieved to have potent antioxidant properties that can neutralize harmful free radicals in the hu-man body. It has also been shown to be beneficial in mitigating oxidative stress-induced damage through its anti-inflammatory and anti-apoptotic pathways. We aim to conduct a systematic re-view to evaluate the potential benefits of hydrogenated water. The review protocol was uploaded on PROSPERO. After the initial search criteria, the articles were reviewed by two blinded inves-tigators, and a total of 25 articles were included in the systematic review. The potential benefits of hydrogenated water on various aspects of health, including exercise capacity, physical endurance, liver function, cardiovascular disease, mental health, COVID-19, oxidative stress, and anti-aging research, are a subject of growing interest and ongoing research. Although preliminary results in clinical trials and studies are encouraging, further research with larger sample sizes and rigor-ous methodologies is needed to substantiate these findings. Current research needs to fully ex-plain the mechanisms behind the potential benefits of hydrogenated water. Continued scientific exploration will provide valuable insights into the potential of hydrogenated water as an adjunc-tive therapeutic approach in the future.

A healthy cornea is a nonvascularized, transparent tissue. It is nourished by diffusion through the tear film, aqueous fluid and neurotrophins supplied by the corneal innervation. The cornea is devoid of both blood and lymphatic vessels, which makes it an immunologi-cally privileged tissue. Corneal neovascularization develops due to an imbalance between angiogenic and anti-angiogenic factors and can lead to a significant decrease in visual acui-ty. It may cause scarring, lipid keratopathy, and corneal edema. The resulting pathological vascularization of the cornea reduces its immune privilege and significantly worsens the prognosis after subsequent penetrating keratoplasty, increasing the risk of rejection of the transplanted flap. Neovascularization is favored by many disease processes, including auto-immune diseases, viral inflammations, mainly herpes and varicella-zoster, and blepharitis [1]. There are several options to treat corneal neovascularization, both pharmacological and surgical. Angiostatic treatment involves inhibiting the growth of new vessels by suppressing inflammatory responses. VEGF inhibitors, steroids, cyclosporine A, and amniotic membrane grafts secured to the cornea work this way. VEGF inhibitors are the agents with the direct and most potent angiostatic effect. Angioregressive treatment, on the other hand, results in the regression of already existing pathological vessels. This therapy is also based on VEGF inhibitors, which, however, have the most potent effect on newly formed and small vessels but are less effective in reducing large-caliber and mature vessels. A more effective method for such vessels is ablation, which involves surgical closure. The most commonly used an-gio-occlusive method is needle diathermy and argon or yellow laser therapy. In advanced corneal neovascularization, corneal transplant surgery may be necessary. It is best performed after pretreatment with anti-VEGF preparations, often continued after corneal transplanta-tion to reduce the risk of transplant rejection [2]. This paper discusses the pathogenesis of corneal neovascularization and the current and future trends in its treatment.

Quinoa, known as the "golden grain" for its high nutritional value, is a significant source of essential nutrients, including proteins, minerals, vitamins, polyphenols, phytosterols, and flavonoids. However, the biological functions of quinoa polysaccharides remain understudied. In this research, two crude quinoa polysaccharides extracts (Q-40 and Q-60) were obtained extracting by 40% and 60% alcohol. The purity of Q-40 and Q-60 was 58.29% and 62.15%, with protein contents of 8.27% and 9.60%, respectively. Monosaccharide analysis revealed that Q-40 contained glucose (Glc), galacturonic acid (GalA), and arabinose (Ara) in a molar ratio of 0.967:0.027:0.006. Q-60 was composed of xylose (xyl), arabinose (Ara), galactose, and galacturonic acid (GalA) with a molar ratio of 0.889:0.036:0.034:0.020. The average molecular weight of Q-40 ranged from 47484 to 626488 Da, while Q-60 showed a range of 10025 to 47990 Da. Rheological experiments showed that Q-40 exhibited higher viscosity, while Q-60 demonstrated more elastic properties. Remarkably, Q-60 showed potent antioxidant abilities, with scavenging rates of 98.49% for DPPH and 57.5% for ABTS. Antibacterial experiments using the microdilution method revealed that Q-40 inhibited the growth of Methicillin-resistant Staphylococcus aureus (MRSA) and E. coli, while Q-60 specifically inhibited MRSA. At lower concentrations, both polysaccharides inhibited MDA cell proliferation, but at higher concentrations, they promoted proliferation. Similar proliferation-promoting effects were observed in HepG2 cells. The research provides important information in application of quinoa in food and functional food industries.

Rhizophora mangle L. is a well-known medicinal plant found in mangroves worldwide used to treatment diabetes. This study evaluated the chemical composition of the acetonic extract from Rhizophora mangle barks (AERM), by HPLC-PDA and FIA-ESI-IT-MS/MS and the effects on high-fat diet induced obesity in mice and its mechanism of action by gene expression of inflammatory markers (Pparg, Ppara, Srebf1, Cd36, Tnf, Ccl2, Lep, Il10, Il6, Fasn, 18s). High-fat diet fed mice during 12 weeks was used as model of obesity and associated alterations. The results were very satisfactory, the extract, rich in polyphenolic compounds, flavonoids and phenolic acids, displayed intense antioxidant activity in vitro (608 µmol Trolox/g), and showed excellent activity against non-alcoholic fatty liver disease (NAFLD) and reverse insulin resistance in a model of diet-induced obesity. We can registered a modulatory effect of AERM in liver PPAR-γ mRNA expression associated to an important inhibition of CD36 mRNA expression suggesting that AERM induces the down regulation of CD36 mRNA via PPAR-gamma inhibition. These results support the traditional knowledge about the use of R. mangle for the treatment of type 2 diabetes and reveal the potential of AERM for the treatment of NAFLD and management of obesity and comorbidities.

Background: The rate of force development (RFD) plays a pivotal role not only in preventing falls but also in ensuring successful completion of many functional tasks that demand swift muscle power rather than prolonged strength. Despite its importance, there is limited compre-hensive research on the relationship between RFD and walking speed, especially in older adults with Sarcopenic Obesity (SO). Objective: to investigate the influence of obesity on neuromuscular markers in older adults with SO and to assess the relationship between neuromuscular markers and gait speed in older adults with SO. Methods: a cohort of 42 participants was categorized based on their BMI into two groups: the sarcopenic non-obese group (CG, n=22; age=81.13±4.02; BMI=25.13±3.35) and the sarcopenic obese group (SOG, n=20; age=77.71±2.95; BMI=34.46±3.25). Gait speed was measured using a 10-meter test. Additionally, the isometric strength of the plantar flexor muscles was assessed during maximal voluntary contractions. Absolute Peak force (aPeak, N) were documented at intervals of 50 ms (a50, N), 100 ms (a100, N), and 200 ms (a200, N), subsequently normalized to body mass (r50, r100, r200, N). The RFD was derived in two phases: from the start of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200) and calculated from the linear slop of the force – time curve (Δ force/Δ time). Conclusion: Obesity negatively impacts neuromuscular markers in older adults. Notably, RFD emerges as the dominant factor influencing gait speed, accounting for an impressive 51% of its variability, far surpassing the impact of relative peak force. This underscores the imperative of evaluating neuromuscular health in older adults with SO to provide insights into mobility out-comes.

Cancer cells exhibit aberrant extracellular matrix mechanosensing due to altered expression of mechanosensory cytoskeletal proteins. Aberrant mechanosensing of the tumor microenvironment (TME) by cancer cells has been shown to be associated with cancer development and progression. Recent studies show that altered mechanosensing changes the mechanobiological properties of cells, and, in turn, cells become susceptible to mechanical perturbations. Due to an increasing understanding of cell biomechanics and cellular machinery, several approaches have emerged to target the mechanobiological properties of cancer cells and cancer-associated cells to inhibit cancer growth and progression. In this review, we summarize the progress that happened in the development of mechano-based approaches to target cancer by interfering with the cellular mechanosensing machinery and overall TME.

Impact force and maximum velocity are important indicators of kick efficiency in fighting activities. Therefore, this systematic review compared the front kick (FK) and roundhouse kick (RK), including maximal and impact force, maximum velocity, maximum angular velocity, and execution time, at different target types and experience levels. The Web of Science, SportDiscus, and PubMed were systematically searched from January 1982 to May 2022, according to PRISMA guidelines. The normalized kicking values were compared using one-way ANOVA. Eighteen articles, including FK with a pooled sample of 113 elite men, 109 sub-elite men, and 46 novices, and 25 articles, including RK with a sample of 238 elite men, 143 sub-elite men, and 27 novice men, fulfilled the inclusion criteria. The primary findings were that the impact forces of FK were higher than RK for the novice, sub-elite, and elite groups by 47% (p<0.01), 92% (p<0.01), and 120% (p<0.01), respectively. Moreover, the maximum foot velocity of RK was faster than FK for the sub-elite and elite groups by 44% (p<0.01) and 48% (p<0.01), respectively. The Elite group had 65% (p<0.01) higher knee extension angular velocity within RK than FK, and 138% (p<0.01) higher hip extension angular velocity within FK than RK.

Tolman VII solution \citep{ref-journal 2} is an exact analytic solution to the Einstein field equations describing the space-time of a static spherically symmetric distribution of matter. The solution has been shown to be capable of describing the interior of compact objects like neutron stars. Generalized \cite{ref-journal 13} and modified \cite{ref-journal 10} versions of the solution are also available in the literature, which have been subsequently developed to accommodate more realistic descriptions of neutron stars. The stability of the modified Tolman VII solution has recently been analyzed by Posada {\em et al} \cite{ref-journal 9 }, who evaluated a critical value of the adiabatic index above which the stellar configuration becomes unstable against radial oscillations. In this paper, making use of the generalized version of the Tolman VII solution, we prescribe an upper bound on the compactness ($M/R$) beyond which the star becomes unstable. Our investigation is based on the stability analysis of a star against radial oscillations developed by Chandrasekhar \cite{ref-journal 1}. The analysis brings out to attention the role of a particular model parameter in the generalized Tolman VII solution which can be linked to the inhomogeneity of the matter distribution vis-a-vis equation of state (EOS).

The detection and enrichment of circulating melanoma cells is a challenge as the cells are very heterogeneous in terms of their biomechanical properties and surface markers. In addition, there is a lack of valid and reliable biomarkers that predict progress and therapeutic response. We here analyzed the elasticity of A375 melanoma cells applying force spectroscopy and a microfluidic method. To identify and eventually separate circulating tumor cells, it is crucial to precisely know their physical properties. First, we used standard AFM force spectroscopy, where the elasticity of the cells is calculated from indentation with a pyramidal tip. To extend the limits of measurement with a tip, we then used cantilevers without a tip to press on the cells over a large area. The resulting Young’s moduli are slightly lower and vary less without tip presumably because of the inhomogeneity of the cells. Finally, we implemented our microfluidic method. We measured single cell elasticity by analyzing its deformation in high-speed micrographs while passing a stenosis. Combining the force field and the change in shape provides the basis for a stress strain diagram. The results from microfluidic deformation analysis were in accordance with the results from force spectroscopy. The microfluidic method provides advantages over conventional methods, since it is less invasive and less likely to harm the cell during the measurement, and the whole cell is measured as one entity without contact to a stiff substrate, while force spectroscopy is limited to the contact area of the tip, and in some cases dependent of the cell substrate interaction. Consequently, microfluidic deformation analysis allows to predict the overall elastic behavior of the whole inhomogeneous cell in three-dimensional force fields. This method may contribute to improve the detection of circulation melanoma cells in the clinical practice.

Classical laws of friction suggest that friction force is proportional to the normal load and independent of the nominal contact area. As a great improvement in this subject, it is now widely accepted that friction force is proportional to the real area in contact, and much work has been conducted based on this hypothesis. In present study, this hypothesis will be carefully revisited by measuring the friction force and real contact area in-site and real-time at both normal loading and unloading stages. Our experiments reveal that the linear relation always holds between friction force and normal load. However, for the relation between friction force and real contact area, the linearity holds only at the loading stage while fails at the unloading stage. This study may improve our understanding of the origin of friction.

As the coproduct of steelmaking, steelmaking slag, volumetrically expansive-prone without treatment, has been satisfactorily used as an aggregate base course material in highway construction. Although numerous technical reports and papers have revealed that steel slag aggreged using in rigid matrixes, the end product, paving block, non-structural concrete, for example, possesses superb strength and durability properties, the application of steel slag aggregate as a concrete aggregate is currently prohibited in highway construction. Naturally, researchers explore the practicality of use of steel slag, how to connect the laboratory experiment results to the end-product behavior, and further convert the research results into real construction? For all nontraditional or secondary materials utilization, the procedure of laboratory material examination, lab and field trial test are critical. To generalize the utilization, usability criteria establishment is necessary. This paper tries to use step-by-step method and plain language to explain how the volumetrically expansion can be simulated in lab testing apparatus, and based on the model, the mathematical deduction can result in a numerical usability criterion for steel slag use as a coarse aggregate in concrete (a rigid material). Therefore the paper is composed four main parts, laboratory test methods to examine the expansion force resulted from steel slag; converting the measured expansion force in a given volume of mass aggregate to the expansion (body) force of a single particle; modeling of slag and end material disruption; and a usability criterion from numerical deduction for the use of expansive-prone coarse slag in concrete or other rigid matrices. The paper provides the solutions to answer the above questions. Through the mathematical and mechanical modeling, provides the potential criteria that could result in specifications and guidance establishment for broad volumetric expansive-prone slags.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

Our report presents the findings from a treatment program that involved plant-based diets (PBDs) and supplements for 1,750 elderly cardiology patients diagnosed with COVID-19 between April 2020 and June 2023. At the start of the program, there was no published data supporting the use of PBDs for COVID-19 patients. However, after 18 months, studies were released that indicated the effectiveness of PBDs in decreasing the incidence and severity of COVID-19. Our treatment protocol differed from these studies in several ways. We carefully controlled the quality, quantity, and processing method of the foods we provided, opting for raw instead of cooked vegetables. Additionally, we incorporated supplementation that complemented the nutrients lacking in a PBD and enhanced the anti-viral, anti-inflammatory, antioxidant, antithrombotic, and immunomodulatory properties of a PBD. Our patients recovered faster (12±1.4 days vs. 20.9±4.3 days), with lower severity (2% vs. 10-20%), hospitalizations (0 vs. 5-10%), and deaths (0 vs. 15-17%) compared to the general population. These favorable outcomes are particularly noteworthy given Indonesia's high COVID-19 morbidity and mortality rates, among the highest in Asia. The findings of this report provide valuable insights for practitioners in managing high-risk elderly COVID-19 patients, particularly in avoiding severity and mortality.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

Neuromyelitis Optica Spectrum Disorder (NMOSD) is a rare immune-mediated relapsing-remitting disease of the central nervous system. The usage of rituximab, to prevent NMOSD relapses, is common in Sweden, but the knowledge on long-term efficacy and risk for severe infections are limited. We performed a retrospective cohort study with medical chart review of rituximab-treated NMOSD patients at the Karolinska University Hospital, Sweden, to assess the occurrence of relapses and severe infectious events (SIE). Furthermore, we collected data on CD19+ lymphocyte, and IgG levels during therapy. A total of 42 NMOSD patients; 24 with aquaporin -4 antibodies (AQP4+), eight with myelin oligodendrocyte glycoprotein antibodies (MOG+) and 10 with absence of antibodies (double-seronegative) were included. During a mean treatment time of 4.4 years, 37% AQP4+, 75% MOG+, and 60% double-seronegative patients experienced 1 relapse. SIEs were common with 46% of AQP4+, 25% of MOG+, and 40% of double-seronegative patients affected. Incomplete CD19+ lymphocyte suppression did not predict a relapse and there was no correlation between IgG levels and SIEs. In conclusion, our data demonstrated a high risk for both relapses and SIEs in rituximab-treated NMOSD patients highlighting the need for close clinical vigilance of disease activity and infections during treatment.

More than 15,000 prescriptions and over the counter drugs are available according to the US Food and Drug Administration website. Moreover, several herbal medicines and dietary supplements are readily available to add to the list of possible drugs, which can potentially cause adverse drug interactions. These are a pressing concern for all as they can interfere with many dental procedures. Additionally, the number of geriatric patients seen in routine dental practice has increased over time. This implies that there are more patients with multiple diseases and health conditions like hypertension, diabetes, problems associated with the cardiovascular, renal and gastrointestinal systems, arthritis, osteoporosis, etc. All these require patients to be on certain medications. Furthermore, advancement in the dental field has led to more complex dental procedures (implants, grafts) being carried out in a general dental practice. These advanced and slightly more invasive treatments require the use of certain drugs before, during and after the treatment like local anesthetics, vasoconstrictors, anxiolytics, analgesics and antibiotics. All of these can possibly interact with medications a patient is already taking and can also interfere with the current dental treatment and create complications. This article aims to provide necessary information about commonly encountered systemic diseases and associated treating medications, their mechanism of action, possible complications and their management. The classes of drugs discussed include anti-platelet agents, vitamin K antagonists, novel oral anticoagulants, bisphosphonates, disease-modifying anti-rheumatic drugs and oral contraceptives.

Abstract: This study reviewed aspects of the biology of two members of the glucosinolate family, namely sinigrin and glucoraphanin and their anti-tumour and anti-microbial properties. Sinigrin and glucoraphanin are converted by the β-sulphoglucosidase myrosinase or the gut microbiota into their bioactive forms, allyl isothiocyanate (AITC) and sulphoraphanin (SFN) which constitute part of a sophisticated defence system plants developed over several hundred million years of evolution to protect them from parasitic attack from aphids, ticks, bacteria or nematodes. Delivery of these components from consumption of cruciferous vegetables rich in the glucosinolates also delivers many other members of the glucosinolate family so the dietary AITCs and SFN do not act in isolation. In-vitro experiments with purified AITC and SFN have demonstrated their therapeutic utility as antimicrobials against a range of clinically important bacteria and fungi. AITC and SFN are as potent as Vancomycin in the treatment of bacteria listed by the World Health Organisation as antibiotic-resistant "priority pathogens" and also act as anti- cancer agents through the induction of phase II antioxidant enzymes which inactivate potential carcinogens. Glucosinolates may be useful in the treatment of biofilms formed on medical implants and catheters by problematic pathogenic bacteria such as Pseudomonas aeruginosa and Staphylococcus aureus and are potent antimicrobials against a range of clinically important bacteria and fungi. The glucosinolates have also been applied in the prevention of bacterial and fungal spoilage of food products in advanced atmospheric packaging technology which improves the shelf-life of these products.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

Based on the panel data from 31 provinces in China from 2012 to 2020, this paper uses the TOPSIS method to measure the development level of the digital economy and environmental quality. Then, a coupled coordination degree model is used to analyse the relationship between the digital economy and environmental quality. Kernel density estimation and the Dagum Gini coefficient method were used to reveal the dynamic evolution trend of the coupled coordination level between the digital economy and environmental quality and the regional trends of coupled indicators. Finally, the dynamics of the above relations were explored with an econometric model. The results show that the coupled coordination degree of the digital economy and environmental quality displays obvious regional heterogeneity, and the national coordination level exhibits dynamic convergence characteristics. The heterogeneity of the coupled coordination degree of the two systems in the eastern region has decreased year by year, except in the western region, the central region and the northeast region, where an upwards trend is observed. Overall, the Gini coefficient of the coupled coordination degree between the digital economy and environmental quality displays a certain downwards trend. The level of economic development, technological innovation level, industrial structure, degree of opening to the outside world, degree of environmental regulation, marketization index and financial development level have a positive influence on the coupled coordination of the digital economy and environmental quality. Environmental regulation is the core driver of the coupling of the two systems, and the economic development level, technological innovation level, industrial structure and degree of openness are the other major drivers. Therefore, in the processes of digital economy transformation and environmental governance, all regions should focus on balanced development between regions to optimize the overall efficiency of the two systems, consider external influence, enhance internal capabilities, and promote the coordination and co-development of the two systems.

We studied the magnetostriction coefficients, λs, Curie temperature, Tc, and their dependence on annealing conditions in Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 amorphous glass-coated microwires with rather different character of hysteresis loops. A positive λs≈20x10-6is observed in as-prepared Fe47Ni27Si11B13C2, while low and negative λs ≈-0.3x10-6 is ob-tained for Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 microwire. Annealing affects the magnetostriction coeffi-cients and Curie temperatures, Tc, of both Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 glass-coated microwires in a similar way. Observed dependencies of hysteresis loops, λs and Tc on annealing conditions are discussed in terms of superposition of internal stresses relaxation and structural relaxation of studied microwires. We observed linear λs dependence on applied stress, σ, in both studied microwires. A decrease with applied stress is observed for Co-rich mi-crowires with negative magnetostriction coefficient. In contrast, a linear increase of the magne-tostriction coefficient with applied stress is observed for Fe-Ni- rich microwires with positive magnetostriction coefficient. Observed results are discussed in terms of influence of internal stresses and short range atomic rearrangements induced by annealing on hysteresis loops, magnetostriction coefficients and Curie temperatures of studied microwires.

When a suspension passes through a high-frequency standing sound wave, the particles it contains are manipulated by acoustic forces. In a one-dimensional sound field, these forces lead to a planar arrangement of the particles and the formation of agglomerates. It is known that the combination of these forces and depth filtration can be utilized to significantly increase the filter efficiency of coarse-pored media. So far, this concept has only been used in microfluidics. In this paper, we present the results of a scaled-up filtration channel to test the viability of the industrial application of acoustically assisted filtration systems for the removal of microparticles. The influences of acoustic power input, flow rate, and the porosity of the filter media are investigated. In addition to verifying the scalability, a significant decrease in the large particle fraction in the outflow of the channel was observed when a high-power sound field is applied. Furthermore, the formed agglomerates tend to rise to the fluid surface. The floating particles mostly consist of a large particle fraction.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Unpaid family caregivers must consider the economic trade-off between caregiving and paid employment. Prior literature has suggested labour force participation (LFP) to decline with caregiving intensity, but no study has evaluated this relationship by accounting for the presence of both kinks and discontinuities. Here we used respondents of the China Health and Retirement Longitudinal Study baseline survey who were non-farming, of working-age (aged 45-60) and had a young grandchild and/or a parent/parent-in-law. For women and men separately, a caregiving threshold-adjusted probit model was used to assess the association between LFP and weekly unpaid caregiving hours. Instrumental variables were used to rule out the endogeneity of caregiving hours. Of the 3,718 respondents in the analysis, for men, LFP was significantly and inversely associated with caregiving that involved neither discontinuities nor kinks. For women, a kink was identified at the caregiving threshold of 8 hours per week such that before 8 hours, each caregiving hour was associated with an increase of 0.0257 in the marginal probability of LFP, but each hour thereafter was associated with a reduction of 0.0014 in the marginal probability of LFP. These results have implications for interventions that simultaneously advance policies of health, social care and labour force.

The entropic gravity conception proposes that what has been traditionally interpreted as unobserved dark matter might be merely the product of quantum effects. These effects would produce a novel sort of positive energy that translates into dark matter via $E=mc^2$. In the case of axions, this perspective as been shown to yield quite sensible, encouraging results [DOI:10.13140/RG.2.2.17894.88641] . There, a simple Schrodinger mechanism was utilized, in which his celebrated equation is solved with a potential function based on the microscopic Verlinde's entropic force advanced in [Physica A {\bf 511} (2018) 139]. In this effort we revisit such technique with regards to fermions' behavior (specifically, baryons).

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

In the manufacturing industry, cutting tool failure is a probable fault which causes damage to the cutting tools, workpiece quality and unscheduled downtime. It is very important to develop a reliable and inexpensive intelligent tool wear monitoring system for use in cutting processes. A successful monitoring system can effectively maintain machine tools, cutting tool and workpiece. In the present study, the tool condition monitoring system has been developed for Die steel (H13) milling process. Effective design of experiment and robust data acquisition system ensured the machining forces impact in the milling operation. Also, ANFIS based model has been developed based on cutting force-tool wear relationship in this research which has been implemented in the tool wear monitoring system. Prediction model shows that the developed system is accurate enough to perform an online tool wear monitoring system in the milling process.

: Since the COVID-19 pandemic, people have become aware that materials (products) can transmit infection and have begun to focus on questions such as how bacteria and germs, the sources of in-fection, maintain their infectivity on material surfaces, and the extent to which materials can or cannot prevent this. and to what extent materials can and cannot prevent it. The SIAA, a non-profit organization of many Japanese companies, had created an entirely separate interna-tional standard for materials' antibacterial, antiviral, and antibiofilm properties (products). The authors have studied the academic basis for the operation of the standards and were deeply in-volved as researchers in establishing one of the standards. This paper describes the interna-tional standards and some representative examples of the authors' actual use of these standards and explains the current status and future problems.

Abstract: In the last decade, gypsogenin has widely grabbed the attention of medicinal chemists by virtue of its prominent anti-cancer potential. Despite its late identification, gypsogenin proved itself as a new an-ti-proliferative player battling for a front position among other classic pentacyclic triterpenes such as oleanolic acid, glycyrrhetinic acid, ursolic acid, betulinic acid, and celastrol. Herein, we present insights into the anti-cancer activity of gypsogenin and its semisynthetic derivatives and go further by introducing our perspective to judiciously guide the prospect rational design. The present article opens a new venue for better exploitation of gypsogenin chemical entity as a lead compound in cancer chemotherapy. To the best of our knowledge, this is the first review article exploring the anti-cancer activity of gypsogenin derivatives.

The synthesis of the presented benzo[d]thiazol-2-amine derivatives was performed by condensing-(4-chlorobenzylidene) benzo[d]thiazol-2-amine with a number of substituted phenols in the presence of potassium iodide and anhydrous potassium carbonate in dry acetone. IR spectroscopy, 1HNMRspectroscopy and spectroscopy methods were used to characterize the structural properties of newly synthesized derivatives. In order to observe the attributes of drug-like candidates of these derivatives, the number of their molecular properties was estimated. Benzo[d]thiazol-2-amine derivatives were molecularly docked with selective enzymes COX-1 and COX-2. Findings suggested that Compounds G3, G4, G6, G8 and G11 possess higher binding affinity than diclofenac sodium, when docking was performed with enzyme COX-1. Compounds G1, G3, G6, G8and G10 showed lower binding affinity than Indomethacin when docking performed with enzyme COX-2.In vitro evaluation of the COX-1 and COX-2 enzyme inhibitory activities were performed for synthesized compounds. Compounds 10 and 11 exhibited significant COX-1 and COX- enzyme inhibitory action with IC50 values of 5.0 and 10 µM, respectively. Using the hot plate method and the carrageenan-induced rat paw edema model, the synthesized compounds were screened for their biological activities, including analgesic and anti-inflammatory activities. The highest analgesic action was exhibited by derivative G11and the compound G10 showed the highest anti-inflammatory response.

Polyacetylene phytochemicals are emerging as potentially responsible for the chemoprotective effects of consuming apiaceous vegetables. There is some evidence suggesting that polyacetylenes impact carcinogenesis by influencing a wide variety of signalling pathways, which are important in regulating inflammation, apoptosis, cell cycle regulation, etc. Studies have shown a correlation between human dietary intake of polyacetylene-rich vegetables with reduced risk of inflammation and cancer. Polyacetylene supplementation can influence cell growth, gene expression, and immunological responses, and reduce tumour number in rat and mouse models. Cancer chemoprevention by dietary polyacetylenes involves several mechanisms, including effects on inflammatory cytokines, the NF-κB pathway, antioxidant response elements, UPR pathway, growth factor signalling, cell cycle progression, and apoptosis. This review summarises the published research on falcarinol-type polyacetylene compounds and their mechanisms of action regarding cancer chemoprevention and treatment, and also identifies some gaps in our current understanding of the health benefits of these polyacetylenes.

： Anti-MDA5 antibody bearing (anti-MDA5+)-dermatomyositis (DM) or polymyositis (PM) is notorious for causing rapidly progressive interstitial lung disease (RPILD) &amp;/or cancers with high mortality rate. However, anti-MDA5 antibodies (Abs) are also found in other connective tissue diseases and their link with RPILD especially with regards to the mortality rate are unknown. We retrospectively recruited 71 patients bearing anti-MDA5-Abs in serum, stratified them in terms of a presence or absence of RPILD, and evaluated their clinical features, laboratory findings, associated myositis antibodies, concurrent connective tissue disease (CTD) as well as newly developed malignancies. Thirty-nine (55%) patients presented with DM/PM but 32 (45%) didn’t. Twenty-two of the former and 11 of the latter developed RPILD eventually, accounting for a total of 46% of all MDA5 bearing patients. On the other hand, 15 of all 71 (21.1%) patients had cancers. Among 32 patients who didn’t have DM/PM, 27 (38.0% of all 71) had other CTDs, indicating that only 5 (7.0% of 71) patients did not have CTDs. Senility (odds ratio [OR]=1.816, P=0.032), presence of anti-Ro-52 antibody (OR=1.676, P=0.018), elevated C-reactive protein (CRP, OR= 4.354, P&lt;0.001) and carcinoembryonic antigen (CEA, OR=2.625, P=0.005) posed risks for RPILD. High lactose dehydrogenase (LDH, p=0.009), CRP (p=0.001), CEA (p=0.001), ferritin (p ≤ 0.001) and low albumin (p ≤ 0.001) were significantly associated with mortality. Anti-SAE antibodies were negatively correlated with RPILD as analyzed by univariate (OR=0.245, P=0.017) and multivariate (OR= 0.058, P=0.036) regressions, indicating that they may be a protective factor from RPILD (OR= 0.543, P=0.008) or fatality (OR= 0.707, P=0.012), which was also demonstrated in subgroup analyses. In contrast to various risk factors for RPILD or mortality, anti-SAE antibodies might be conversely a protective factor in anti-MDA5+ patients.

Background: Antiphospholipid antibodies (aPL) are a laboratory criterion for the classification of antiphospholipid syndrome (APS), and are known to cause clinical symptoms: vascular thrombosis or obstetric complications. It is suggested that aPL may be associated with thromboembolism in severe COVID-19 cases. Aim: to combine clinical data with aPL findings at 4 time points (admission, worsening, discharge, 3-month follow-up) in patients hospitalized with COVID-19 pneumonia. Methods: current and past history of thrombosis and obstetric complications; aPL determined at 4 time points: anticardiolipin (aCL), anti-β2-glycoprotein I (anti- β2GPI) and antiphosphatidylserine/prothrombin (aPS/PT) of the IgM, IgG or IgA isotypes. Results: 111 patients with COVID-19 pneumonia were enrolled. During hospitalization, 7 patients died, 3 of them due to pulmonary artery thromboembolism (none was aPL positive). Only one of the five who developed pulmonary artery thrombosis was aPL positive. Of 9/101 patients with a history of thrombosis, 5 had arterial thrombosis and none was aPL positive at admission and follow-up; 4 had venous thrombosis and one was aPL positive at all time points (newly diagnosed APS). Of these 9/101 patients, 55.6% were transiently aPL positive at discharge only, compared to 26.1% without history of thrombosis (p=0.05). Conclusions: aPL were not associated with fatal outcomes and vascular thrombosis; aPL were transiently positive in more than half of patients with a history of thrombosis.

Background and Objectives: Age-related macular degeneration (AMD) is one of the major causes of central vision loss in the older age group and its dry form accounts for the majority of cases. Although several causes and mechanisms for the development and progression of AMD have previously been identified, the pathogenesis of this complex disease is still not entirely understood. As the inflammation and involvement of the immune system are strongly suggested to have a central role to promote the degenerative process and to stimulate the onset of complications, we aimed to analyze the prevalence of serum anti-retinal (ARA) and anti-endothelial cell antibodies (AECA) in patients with dry AMD and to determine their relationship with the clinical features of the disease, notably area of geographic atrophy (GA). Materials and Methods: We enrolled 41 patients with dry AMD and 50 sex- and age-matched healthy controls without AMD. The presence of ARA was determined by indirect immunofluorescence using monkey retina as an antigen substrate, while the presence of AECA was determined using cultivated human umbilical vein endothelial cells and primate skeletal muscle. Results: ARA were detected 36 (87.8%) AMD patients (titers range from 1:20 to 1:320) and in 16 (39.0%) (titers range from 1:10 to 1:40) of controls (p=0.0000). Twenty of the 41 patients (48.8%) were positive for AECA, while in a control group AECA were present only in 5 sera (10.0%). The titers of AECA in AMD patients ranged from 1:100 to 1:1000 and in the control group the AECA titers were 1:100 (p=0.0001). There were no significant correlations between the presence of AECA and disease activity. Conclusions: This study provides evidence for the possible involvement of an autoimmune process against retina and retinal vessel antigens in the pathogenesis of geographic atrophy associated with dry AMD.

The West-African variety of Sorghum bicolor leaf sheath (SBLS) Jobelyn® is a natural remedy, which has gained international recognition for its anti-anemic effect and energy boosting qualities in debilitating diseases. The widespread use of traditional medicine in the region usually confirms its safety, but not its efficacy or deep assessment of their pharmacological properties. The other major issue for herbal-based treatments is the lack of definite and complete information about the composition of the extracts. Despite limitations, efforts have been made in isolation and characterisation of active compounds in this specie of sorghum showing various subclasses of flavonoids including apigeninidin, a stable 3-deoxyanthocyanidin and potential fungal growth inhibitor, which accounts for 84% of the total extract. Non-clinical in vitro and in vivo studies support previous indications that this variety of Sorghum bicolor possesses several biologically active compounds with potent antioxidant, anti-inflammatory, anti-aging and neuro-protective properties. Clinical studies show that SBLS has the ability to boost hemoglobin concentrations in anemic conditions and most remarkably to increase CD4 count in HIV-positive patients. The multiple effects and high safety profiles of this extract may encourage its development as a therapeutic agent for the treatment of anemia, chronic inflammatory conditions or in the symptomatic management of HIV infections. This review describes the potential therapeutic aspects of SBLS extract and its potential benefits.

Despite extensive use of intravitreal anti-vascular endothelial growth factor (anti-VEGF) biologics for over a decade, neovascular age-related macular degeneration (nAMD) or choroidal neovascularization (CNV) continues to be a major cause of irreversible vision loss in developed countries. Many nAMD patients demonstrate persistent disease activity or experience declined responses over time despite anti-VEGF treatment. The underlying mechanisms of anti-VEGF resistance are poorly understood, and no effective treatment strategies are available to date. Here we review evidence from animal models and clinical studies that supports the roles of neovascular remodeling and arteriolar CNV formation in anti-VEGF resistance. Cholesterol dysregulation, inflammation, and ensuing macrophage activation are critically involved in arteriolar CNV formation and anti-VEGF resistance. Combination therapy by neutralizing VEGF and enhancing cholesterol removal from macrophages is a promising strategy to combat anti-VEGF resistance in CNV.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

Diabetic foot is a serious complication that poses significant risks for diabetic people. The resulting reduction in protective sensitivity in the plantar region requires early detection to prevent the imminent ulceration and amputation. The primary method employed for evaluating this sensitivity loss is the 10 g f Semmes-Weinstein monofilament test, commonly used as a first-line procedure. However, the lack of calibration in existing devices often introduces decision errors due to unreliable feedback. In this paper, a new equipment designed to address these limitations and enhance the assessment of the sensitivity loss using the 10 g f monofilament is introduced. The proposed system automates metrological verification and evaluation processes, ensuring accurate and reliable results. Furthermore, it simulates the practitioner’s procedure, serving both as a valuable training tool and a means to provide force-feedback information. An analytical model of the monofilament buckling and deflection is also presented. The obtained results showed that the tested monofilaments had a very high error compared to the 10 g f declared by the manufacturers. It is aimed, by introducing this advanced equipment, to improve the precision and reliability of assessing the sensitivity loss. The integration of automated verification, simulation capabilities, and precise measurements shows great promise for diabetic patients, reducing the likelihood of adverse outcomes such as ulceration and amputation.

The complex dynamics of the neocortex, the outermost layer of the brain, have been a subject of intense research in neuroscience. Recent studies have suggested that magnetic fields generated by neuronal activity may play a significant role in neocortical dynamics. This paper presents a simplified mathematical model that explores the hypothesized interactions between magnetic dynamos, nondissipative systems, Hamiltonian equations, and the Lorenz force in the context of neocortical dynamics. The proposed model is based on a set of coupled Hamiltonian equations inspired by the Lorenz system, a well-known chaotic dynamical system. The generalized coordinates in the model represent the magnetic field components, while the generalized momenta are related to the electric field components or other relevant quantities. The Hamiltonian equations describe the conservative dynamics of the system, and the coupling terms in the equations are interpreted as representing the interactions between the magnetic and electric field components, analogous to the Lorenz force in electromagnetism. The model is implemented using Python, and the Hamiltonian equations are numerically solved using the odeint function from the scipy.integrate module. The resulting dynamics of the magnetic field components are visualized using matplotlib. While the model is highly simplified and does not capture the full complexity of neocortical dynamics, it serves as a starting point for investigating the potential role of magnetic dynamos and Lorenz force interactions in the brain. The paper discusses the limitations of the current model and highlights the need for further refinements, such as incorporating more realistic biological constraints, considering energy dissipation and compensation mechanisms, and validating the model against experimental data. Future work should focus on developing a more comprehensive and biologically plausible model that integrates the latest findings from neuroscience, physics, and computational modeling. By presenting this simplified Hamiltonian model, the paper aims to stimulate further research and discussion on the potential significance of magnetic dynamos and Lorenz force interactions in neocortical dynamics. The model provides a framework for exploring these hypothesized mechanisms and may guide future experimental and theoretical investigations in this emerging field of neuroscience

The ageing global population and changing labor force participation are having a profound impact on state pension programs worldwide, including Malaysia. However, the effects of an ageing workforce and declining fertility rates are having a significant impact on future trends in labor force participation and the duration of retirement. This paper presents an innovative examination of labor force participation rate (LFPR) forecasting within the context of an aging workforce, utilizing the Lee-Carter and Cairns-Blake Dowd stochastic models, traditionally applied to mortality data. By adapting these models to LFPR data, the study offers a novel perspective on predicting workforce participation trends and understanding the dynamics of retirement planning from year 2001 to 2047. Additionally, by incorporating the mortality forecasts from the United Nations, the research navigates through the complexities of applying actuarial methods to labor economics, revealing differentiated pathways for male and female participation in the labor market and the anticipated length of retirement. This study offers a unique comparison between the Lee-Carter and the Cairns-Blake-Dowd (CBD) LFPR models. It focuses on fitting and forecasting the LFPR of senior employees aged 50 to 64. The results highlighted discrepancies among models that demonstrated evidence of model risk for extended retirement duration.

This paper focuses on improving the tracking accuracy for servo systems and increasing the contouring performance of precision machining. The dynamic friction during precision machining is analyzed using the LuGre model. The dynamic and static parameters in the friction model are efficiently and accurately identified using the improved Drosophila Swarm Algorithm based on cross-mutation. The friction tracking error can be deduced by the friction state space and an expression is derived. To compensate for the tracking error caused by friction, a feedforward compensation control is designed to avoid signal lag in traditional friction controllers. Furthermore, the factors of multi-axis parameter mismatching that impact the machining profile accuracy are analyzed for multi-axis control. An adaptive cross-coupled control-based pre-compensation strategy of contour error is designed to reduce both the tracking error and the contour error. The effectiveness of the proposed method is validated through several experiments, which demonstrate a remarkable improvement in tracking performance and contour accuracy.

Real-time multi-axis distributed tactile sensing is a critical capability if robots are to perform stable gripping and dexterous manipulation, as it provides crucial information about the sensor-object interface. In this paper, we present an optical-based 6-axis tactile sensor designed in a fingertip shape for robotic dexterous manipulation. The distributed sensor can precisely estimate local XYZ force and displacement at ten distinct locations, and provide global XYZ force and torque measurements. Its compact size, comparable to that of a human thumb, and minimal thickness allow seamless integration onto existing robotic fingers, eliminating the need for complex modifications to the gripper. The proposed sensor design uses a simple, low-cost fabrication method. Moreover, the optical transduction approach uses light angle and intensity sensing to infer force and displacement from deformations of individual sensing units that form the overall sensor, providing distributed 6-axis sensing. The local force precision at each sensing unit in the X, Y, and Z axes is 20.89 mN, 19.19 mN, and 43.22 mN, respectively, over an local force range of approximately ±1.5 N in X and Y and 0 to -2 N in Z. The local displacement precision in the X, Y and Z axes is 56.70 μm, 50.18 μm and 13.83 μm, respectively, over a local displacement range of ±2 mm in the XY directions and 0 to -1.5mm in Z (i.e., compression). Additionally, the sensor can measure global torques, Tx, Ty and Tz, with a precision of of 1.90 N-mm, 1.54 N-mm and 1.26 N-mm, respectively. The fabricated design is showcased by integrating it with an OnRobot RG2 gripper and illustrating real-time measurements during in simple demonstration task which generate changing global forces and torques.

The world population is aging, which along with recent shifts in the labor force participation (LFP), is having a significant longevity influence on state pension programs across the board, including Canada, Finland, Japan, and Germany. Except Japan, these countries have set their statutory re-tirement age at 65, but the impact of aging workforce and declined fertility rates create wonders on the estimate future trends in the LFP, as well as the length of retirement. In this study, we fit the LFP rates of these countries, representing continents from Asia, Europe and North America among the OECD countries, using the Lee-Carter and Cairns-Blake-Dowd (CBD) stochastic models. The es-timates are then used for the projection of future LFP rates (1989-2066), and by combining the mortality forecasts from the United Nations, we project the expected length of retirement (1989-2066). This study provided a novel comparison between the Lee-Carter and the CBD LFP models by fitting and forecasting the LFP rates of senior employees between 50- to 74-year-olds. The results revealed disparities between models that provided proof of the presence of model risk for longer retirement durations. The study findings emphasized the importance for decision-makers in pension industry to have awareness of potential risks and limits associated with the LFP models. The Lee-Carter model outperformed the CBD model even though the CBD model is known for its ac-curate prediction in higher ages. Population aging should be considered in any analysis of the long-term viability of pensions, together with the participation rate trends for a sustainable labor market future.

In this paper, a mathematical and physical interpretation of the length and the angle of the catenary curve made by the anchor chains was implemented, and the safety of an anchored vessel was reviewed. So far, holding force has been calculated approximately when the angle of the catenary curve of the anchor chain to the seafloor is 0°. In this study, the holding force equation was strictly derived for the case of anchor dragging. In addition, the equations for the angle and length of the catenary curve were mathematically derived when the anchor dragging occurs. The holding force equation derived in this paper are expected to help provide guidelines in vessel design or increase the safety of anchoring.

Viroids represent the simplest, but are also among the most interesting life-like forms. They represent a great problem in agriculture. Moreover, pathogens similar to viroids, such as the hepatitis Delta virus represent a risk for human health. Viroids encode no proteins, but are still able to hijack their host cells’ metabolism to perform multiplication. This paper attempts to reply three questions about viroids. First, how can viroids hijack their host cells’ metabolism, even though they encode no proteins to achieve this? Second, what advantages do viroids have from their simplicity? Third, what can viroids, as the simplest life-like forms, tell us about life as a natural phenomenon? These questions are discussed from the perspective of biothermodynamics. In order to do this, elemental composition, biosynthesis reactions and standard thermodynamic properties of viroids have been determined and analyzed.

Holding an object by clamping force is a fundamental phenomena, layered or laminated architectures with internal sliding features are essential mechanism in natural and man-made structural system. In this paper, we combine the layered architecture and clamping mechanism to form a multilayered clamp and study the clamping force with internal friction. Our investigations show that the clamping force and energy dissipation are very mich depend on the number of layers, its geometry and elasticity, as well as internal friction. The central goal of studying the covered book is not only to predict the clamping force of the clamp, but also as a representative case to help finding some clue on the universal behaviours of multilayered architectures with internal friction.

Granular superconductivity at high temperatures in graphite can emerge at certain two-dimensional (2D) stacking faults (SFs) between regions with twisted (around the c-axis) or untwisted crystalline regions with Bernal (ABA...) and/or rhombohedral (ABCABCA...) stacking order. One way to observe experimentally such 2D superconductivity is to measure the frozen magnetic flux produced by a permanent current loop that remains after removing an external magnetic field applied normal to the SFs. Magnetic force microscopy was used to localize and characterize such a permanent current path found in one natural graphite sample out of ∼50 measured graphite samples of different origins. The position of the current path drifts with time and roughly follows a logarithmic time dependence similar to the one for flux creep in type II superconductors. We demonstrate that a ≃10nm deep scratch on the sample surface at the position of the current path causes a change in its location. A further scratch was enough to irreversibly destroy the remanent state of the sample at room temperature. Our studies clarify some of the reasons for the difficulties of finding a trapped flux in remanent state at room temperature in graphite samples with SFs.

In this paper, we have shown the electronic circuit equivalence of a mechanical system consists of two oscillators coupled with each other. The mechanical design has the effects of the magnetic, resistance forces and the spring constant of the system is periodically varying. We have shown that the system’s state variables, such as the displacements and the velocities, under the effects of different forces, lead to some nonlinear behaviors, like a transition from the fixed point attractor to the chaotic attractor through the periodic and quasi-periodic attractors. We have constructed the equivalent electronic circuit of this mechanical system and have verified the numerically obtained behaviors using the electronic circuit.

During operation, the support bracket is the main part to withstand the axial loads of the pumped storage unit. Moreover, the effects of axial loads including the hydraulic thrust of runner flow and the weight of runner body may cause the support bracket deformation and fatigue damage. For the safe and stable operation, the simulation of the axial force and the structural analysis of the support bracket of a pumped storage unit was carried out in this paper. The CFD simulation result has revealed the variation rule of the axial force in different operating conditions. Using ANSYS Mechanical, the static stresses and deformation of support bracket with axial loads were calculated. The results release the location and variations of maximum stress and maximum deformation caused by the axial loads. By comparing the predicted maximum axial force with the admission force calculated by the structural analysis, it is found that the axial force of the researched machine is within the safe range. This study provides the reference for the safety and stable operation of the pumped storage unit.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

An entropic origin of gravity is re-visited. Isothermal self-gravitating cloud seen as an ideal gas is analyzed. Gravitational attraction within the isothermal cloud in equilibrium is balanced by the pressure, which is of a pure entropic nature. The notion of the Jeans entropy of the cloud corresponding to the entropy of the self-gravitating cloud in mechanical and thermal equilibrium is introduced. Balance of the gravitational compression and the entropic repulsion yields the scaling relation hinting to the entropic origin of the gravitational force. The analysis of the Jeans instability enables elimination of the “holographic screen” or “holographic principle” necessary for grounding of the entropic origin of gravity.