The present work sets out the evaluation of composite laminates through optimization objective functions. Genetic Algorithms (GA), as well as Simulated Annealing (SA), were performed in order to determine the optimal ply orientations of a fiber-reinforced polymer laminate for three given load cases: 1) in-plane loads, 2) combined moments, and 3) in-plane loads and combined moments. It searches the optimal orientation layup, which fulfills at the same time both the maximum strain criterion and the Tsai-Wu failure criterion. Construction of an objective function based on the strains and the stresses involves a minimization process to deformations and a maximization of the safety factor. For the first load case, the initial solution is [±45/0/90/±45]s, and the best solution is [(45/135)2/452]s. For the second load case, [-45/45/45/-45/0/90]s is the initial layup sequence, then the best solution obtained is [(45/-45)2/452]s, where plies at 0° and 90º are not necessary even when axial loads are applied. For the third study case, the original layup sequence is [0/45/-45/45/0/90]s; meanwhile, the best solution calculated is [21/24/145/140/45/49]s. An interesting observation is that each pair of layers has a 5º gap. The simulations show that the qualitative results from the GA are better than the SA, but with a significantly higher computational cost. These kinds of computational tools are expected to be used as a reference guide for an optimal fiber configuration with respect to the common orientations used when composite laminates are designed for a structural application.

Titica vine fibers (TVFs) extracted from aerial roots of Heteropsis flexuosa, from the Amazon region, were 10, 20, 30 and 40 vol% incorporated into an epoxy matrix for applications in ballistic multilayered armor systems (MASs) and stand-alone tests for personal protection against high-velocity 7.62 mm ammunition. The back-face signature (BFS) depth measured for composites with 20 and 40 vol% TVFs used as an intermediate layer in MASs was 25.6 and 32.5 mm, respectively, below the maximum limit set by the international standard. Fracture mechanisms found by scanning electron microscopy (SEM) attested the relevance of increasing the fiber fraction for applications in MASs. The results of stand-alone tests showed that the control (0 vol%) and samples with 20 vol% TVFs absorbed the highest impact energy (Eabs) (212 – 176 J), and consequently limit velocity (VL) values (213 – 194 m/s), when compared with 40 vol% fiber fractions. However, the macroscopic evaluation found that the plain epoxy, referring to control samples, shattered completely. In addition, for 10 and 20 vol% TVFs, the composites were fragmented or exhibited delamination fracture, which contributed to their physical integrity. On the other hand, the composite with 30 and 40 vol% TVFs, whose Eabs and VL varied between 166 – 130 J and 189 – 167 m/s, respectively, showed the best dimensional stability. The SEM images indicated that for composites with 10 and 20 vol% TVFs the fracture mode was predominantly brittle, due to the greater performance of the epoxy resin and the discrete action of the fibers. While for composites with 30 and 40 vol% TVFs, there was the activation of more complex mechanisms such as pullout, shearing and fiber rupture.

Although the Orthotropic steel decks (OSDs) have been widely used in the construction of long-span bridges, there are frequently reported fatigue cracks after years of operation, and the bridge deck overlay also presents severe damage due to OSD crack-induced stiffness reduction. The ultra-high performance concrete (UHPC), recognized as the most innovative cementitious composites and the next generation of high-performance materials, shows high strength, ductility, toughness and well performance on durability. After its first application to the OSD bridge in early 2000s, the orthotropic Steel-UHPC composite deck has been comprehensively studied worldwide. This review will summarize some important studies and findings on behavior and fatigue performance of orthotropic steel-UHPC composite deck. The existing studies and engineering application indicate that such deck system presents good bending behavior and high fatigue performance. The failure mode of shear studs in UHPC layer is dominated by shear fractures. The cracking of UHPC layer shall consider the superposition effect of stress from both the whole bridge structure and local decks. While some reasonable structural details in the traditional OSD may not work for the orthotropic steel-UHPC composite deck. It is recommended to evaluate the stress behavior and structural parameters, as well as fatigue life by conducting the field test under in-service traffic conditions.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

The use of carbon nanotubes to improve the mechanical properties of polymers is one of the promising directions in materials science. The addition of single-walled carbon nanotubes (SWCNT) to a polymer results in significant improvement of mechanical, electrical, optical, and structural properties. However, the addition of SWCNTs does not always improve the polymer properties. Also, when a certain content of SWCNTs is exceeded, the mechanical properties of the nanocomposite are getting worse. This article reports the results of computer simulations for predicting the mechanical properties of polymer/single-walled carbon nanotube nanocomposites. The efficiency of reinforcing polymer composites is considered depending on the concentration of carbon nanotubes in the polymer matrix, their size and structure. The elastic moduli of the nanocomposites were predicted using computer simulations for unit cell tension (0.1%). General trends in the mechanical properties of composites with polypropylene, poly (ethyl methacrylate), polystyrene matrices and SWCNTs are shown.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

Mechanically strong and thermally stable films obtained from a water-based polyurethane (PU) dispersion with small (0.1–1.5 wt.%) additions of graphene oxide nanosheet (GO) were studied through elemental analysis, X-ray photoelectron spectroscopy, differential thermogravimetry, and Raman spectroscopy. Moreover, the depletion of near-surface layers in nitrogen was presented for all the samples under study. It was found that the introduction of GO into a PU matrix was ac-companied by a partial reduction of graphene oxide nanosheet and an increase in the concentra-tion of defects in its structure.

Objective. Political instability, corruption, exclusive institutions et al. are some of the hypotheses backed by literature as to why some nations are more developed than others. One hypothesis which has not been intensively studied is the culpability of individual and institutional behavior and its impact on development. To examine the validity of such a hypothesis, a composite index which quantifies such development hindering behavior must be developed. The prelude to developing this index is to investigate whether such a quantitative measure exists to begin with. To achieve this objective, a bibliometric analysis of Scopus and Web of Science databases will be conducted. Method. A bibliometric and content analysis of Scopus and Web of science databases using Excel, VOSviewer, and R software. Results. The findings of the bibliometric analysis indicate the absence of such measure particularly within the scope of ‘bad behavior’, ‘unethical behavior’, and ‘development’. Conclusions. The study findings provide the greenlight to proceed with the construction of the ‘Bad Behavior Index’. Contribution. The practical contribution of this study is that it provides researchers with an improved methodology on how to conduct a bibliometric analysis to identify the absence of knowledge and provide a justification for the creation of such knowledge by integrating and analyzing two journal databases instead of one, using three mediums: Excel, VOSviewer, and R software.

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

Agricultural wastes have posed as a treat to the environment over the years and they are found in large quantities due to domestic and industrial utilization of such materials in under developed and developing countries. The inability to recycle this waste has led to researches on how to use them in carrying out productive industrial activities. The aim of this study is to use Central Composite Design (CCD) to optimize the bleaching effects by snail shell as adsorbents on crude palm oil. The predictive ability of the model was close to accurate using MINITAB 19 software with the design application for the process simulation for % FFA yield to have 75.856% for experimental and 77.587% for predicted yield with just 1.731% residual. The saponification value increased with adsorption, and it indicates that palm oil can be used for soap making.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

An equilibrium problem of the Kirchhoff-Love plate containing a nonhomogeneous inclusion is considered. It is assumed that elastic properties of the inclusion depend on a small parameter characterizing width of the inclusion $\varepsilon$ as $\varepsilon^N$ with $N<1$. The passage to the limit as the parameter $\varepsilon$ tends to zero is justified, and an asymptotic model of a plate containing a thin inhomogeneous hard inclusion is constructed. It is shown that there exists two types of thin inclusions: rigid inclusion ($N<-1$) and elastic inclusion ($N=-1$). The inhomogeneity disappears in the case of $N\in (-1,1)$.

Graphene-oxide (G) was prepared by the Hummers’ method. A G-COOH layer was synthesised using chloroacetic acid and G. To fabricate carboxylated graphene-RuO2 (G-COORu) nano¬¬-composites, RuO2 nano particles were grown on graphene layers using a one-step thermal method, -COOH(G-COOH), and RuCl3. All materials were characterised using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, 13C-nuclear magnetic resonance as well as X-ray photoelectron, Fourier-transform infrared spectroscopy, and Raman. The electrochemical characteristics of the G-COORu supercapacitors were analysed using electrochemical impedance spectroscopy, cyclic voltammetry, constant current charge–discharge tests, and Nyquist impedance plots. The supercapacitors exhibit a specific capacitance of ~125 F g-1 at 100 mA cm-2 within the potential range of 0–1.0 V. The method used here provides a simple approach for the deposition of RuO2 nano particles on graphene layers and can be widened to the fabrication of other classes of hybrids based on G layers for specific technical applications.

Homogeneous water dispersions of MWCNTs were prepared by ultrasonication in the presence of an amphiphilic polystyrene-block-poly(acrylic acid) (PS-b-PAA) copolymer. The ability of PS-b-PAA to disperse and stabilize MWCTNs was investigated by UV-vis, SEM and zeta potential. It is shown that the copolymer can disperse nanotubes directly by sonication in water. The results show that the addition of a styrene block to PAA enhances the dispersion efficiency compared to pure PAA, possibly due to the nanotube affinity with the polystyrene moiety. Notably, the dispersions show an evident pH-responsive behavior, being MWCNTs reaggregation promoted in basic environment. Furthermore, composites obtained by drop casting display electrical conductivity responsive to pH variations, showing the potential of such materials for sensing applications.

Magnesium is one of the lightest structural metal used in different industrial sector and many works are present in literature about the study of its reinforcement by fillers addition. Basalt fibres are natural fillers with good mechanical properties, excellent resistance to high temperature and lower cost than carbon fibres. For these aspects, in the last years they are increasingly used in the production of composite materials with polymeric matrices. However, very few information are presents in literature about the use of basalt fibres as reinforcement in metal matrix composite materials. It is well known that the impregnation of fibres reinforcement affects the mechanical behavior of composites materials. The aim of this study is to investigate the impregnation and the behavior of basalt fibres in a magnesium alloy composite material manufactured by a centrifugal casting technique.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

The objective of this article was to forecast the ultimate failure load laminate stacking sequence combination on bonding joints which are exposed to tensile strength by using artificial neural networks. We have glass fiber composite materials with three different sequence combinations ([0°/90°], [±45°], [0°/90°/±45°]). Various adherend thicknesses and also ductile type adhesive was used in the experiment. The bonding geometry is a single lap and has four types of overlap angles 30°, 45°, 60°, 75° respectively. The experimental results demonstrate that composite laminate stacking sequence profoundly affects the bonding joints of failure load. Taking experimental results into account, Levenberg–Marquardt learning algorithm model was used by preferring a three layer forward on ANN so as to discipline network. In order to procure a precise ANN tool, an integrate methodology of experimental method has been used. The outcomes are used to ensure the experimental data’s to the ANN. The method of ANN permits surveying much adequately the probabilities of composite laminate stacking sequence combination using the prevalent ones which are [0°/90°], [±45°] and [0°/90°/±45°]. Testing data and training results were quite well 0.998, 0.997 and 0.998 in turn. Consequences acquired can be used by engineers who are interested in the composite material design to enhance failure load.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Carbonous nanomaterials are promising additives for composite coatings for heat-dissipation materials because of their excellent thermal conductivity. Here, copper/carbonous nanomaterial composite coatings were prepared using nanodiamond (ND) as the carbonous nanomaterial. The copper/ND composite coatings were electrically deposited onto copper substrates from a continuously stirred copper sulfate coating bath containing NDs. NDs were dispersed by ultrasonic treatment, and the initial bath pH was adjusted by adding sodium hydroxide solution or sulfuric acid solution before electrodeposition. The effects of various coating conditions—the initial ND concentration, initial bath pH, stirring speed, electrical current density, and the amount of electricity—on the ND content of the coatings were investigated. Furthermore, the surface of the NDs was modified by hydrothermal treatment to improve ND incorporation. A higher initial ND concentration and a higher stirring speed increased the ND content of the coatings, whereas a higher initial bath pH and a greater amount of electricity decreased it. The electrical current density showed a minimum ND content at approximately 5 A/dm². Hydrothermal treatment, which introduced carboxyl groups onto the ND surface, improved the ND content of the coatings. A copper/ND composite coating with a maximum of 3.85 mass% ND was obtained.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

When the power converter connected to the high-frequency transformer breaks through the bottleneck and reaches a frequency of 100kHz or even higher, the high-frequency transformer's inter-turn insulation faces more serious high-frequency discharge and high temperature problems. In order to improve the service performance of oil-immersed high-frequency transformer insulation paper, composite K-BNNSs particles are prepared by ultrasonic stripping, heat treatment and thermomagnetic stirring. Then, K-BNNSs particles are mixed with PMIA slurry to produce composite aramid paper. And the effects of K-BNNSs particles with different contents on the thermal conductivity, dielectric properties, partial discharge properties and mechanical properties of aramid paper are explored. It can be found that when the addition of composite particles (K-BNNSs) is 10%, the comprehensive performance of composite aramid paper is the best. Compared with Nomex paper, the in-plane and through-plane thermal conductivity of composite insulating paper F-10 is increased by 668.33% and 760.66% respectively. Besides, the high-frequency breakdown voltage is increased by 48.73% and the tensile strength is increased by 2.49%. The main reason is that the composite particles form a complete thermal conductive network in the aramid paper matrix and a large number of hydrogen bonds with the matrix, which enhances the internal interface bonding force of the material and changes the charge transport mechanism.

There are different audit methods for analysing operational facts and identifying deficiencies in business process management. However, financial data and transactions indirectly relate to physical objects and their attributes, resulting in distinct characteristics for their analysis and auditing methods. It is important to find new methods for finding a process extraction solution based on the financial audit data space to increase the efficiency of the auditors' work by reducing their time costs and increasing the possibility of detecting financial anomalies in large amounts of financial data. The research presents discussed different financial data space (FDS) methods, and process mining (PM) that include related classifications of financial data and external and internal factors that can influence data behavior (value changes) and the peculiarity of FDS is that it includes not only the characteristics of financial data but also other operational characteristics (events, environmental and internal changes, business location) that may be related to the change in financial objects (FO) values. The authors of the paper discuss the prototypes of specific elements in financial data analysis that were developed using the Process Mining software tool Disco and present the conclusions of the effectiveness of the financial processes cube defined to increase the analytical possibilities of the auditor's work with large amounts of data, introducing more flexible functionality for the analysis of financial activities.

In order to study the corrosion resistance of 904L composite plate pressure vessel under high temperature and high pressure gas field environment, the pitting corrosion and stress corrosion cracking resistance of 904L composite plate body and weld material were compared with those of 2205 composite plate and 825 composite plate, which have been used in high temperature and high pressure gas field environment. The results showed that the pitting resistance of 904L composite plate was lower than that of 825 composite plate and higher than that of 2205 solid solution pure material plate and 2205 composite plate. The corrosion resistance of welds on 904L composite plate with different materials was very different. The corrosion rate of 904L composite plate body, welding seam and surfacing welding were all slight corrosion, and the sensitivity of chloride stress corrosion cracking was low in the simulation of the corrosion environment of high temperature and high pressure gas field. 904L composite plate met the requirements of corrosion resistance of pressure vessel material in high temperature and high pressure gas field environment.

In this paper, aiming at the safety evaluation of ultimate bearing safety capacity of composite pile bridge foundation, the symmetrical reliability method with forward and inverse analysis con-sidering the randomness of parameters is proposed to evaluate the safety performance of com-posite pile foundation. The proposed method, considering the randomness of parameters, was used to calculate the safety factor of ultimate bearing capacity of composite pile foundation to meet the prescribed target reliability requirements. Through the example calculation of the safety coefficient of pile foundation, the results show that the statistical characteristics of random vari-ables that affect the safety coefficient of pile foundation have a significant impact. The degree of the safety coefficient depends on the probability distribution type and distribution parameters of the random parameters, among which the more important is the variation characteristics of the random variables. The stronger the parameter variability, the lower the safety level of the struc-ture. During design and evaluation, it is necessary to measure the safety reserve of pile founda-tions in accordance with engineering practice to ensure the safe construction and well operation of the pile.

This in vitro study aimed to analyze the surface roughness (Ra) and color stability (ΔEab, ΔE00) following simulated mechanical brushing, and to evaluate the microtensile (μTBS) to dentin of Self Adhering Resin Flowable (SARF). The selected materials were Constic, Yflow AS, and Tetric N flow (TNF/control). Thirty composite resin cylinders were fabricated for surface property evaluation. Ra and color were assessed both before and after simulated brushing. The thresholds of 50:50% perceptibility and acceptability of color difference of the evaluated resins were assessed. For μTBS analysis, fifteen molars were selected, sectioned to expose flat dentin surfaces, and restored according to manufacturers' instructions. Subsequently, they were sectioned into sticks for microtensile testing. Statistically significant differences in Ra among the groups, with Constic exhibiting the highest Ra value (p < 0.05), while Yflow AS showed the lowest Ra value. No statistically significant difference in color was observed among the groups (p > 0.05). The 50:50% perceptibility and acceptability thresholds set at 1.2 and 2.7 for ΔEab and 0.8 and 1.8 for ΔE 00. All the results fell within the acceptable limits. The mean μTBS values of Constic, Yflow AS, and TNF were 10.649 MPa, 8.170 MPa, and 33.669 MPa, respectively. The study revealed increased Ra and comparable color stability among all tested composite resins after abrasion. However, SARF exhibited lower μTBS compared to conventional using an adhesive system.

The management of vision-threatening retinal diseases remains challenging due to the lack of an effective drug delivery system. Encapsulated cell therapy (ECT) offers a promising approach for the continuous delivery of therapeutic agents without the need for immunosuppressants. In this context, an injectable and terminable collagen-alginate composite (CAC) ECT gel, designed with a Tet-on pro-caspase-8 system, was developed as a safe intraocular drug delivery platform for the sustained release of glial cell line-derived neurotrophic factor (GDNF) to treat retinal degenerative diseases (RDDs). This study examined the potential clinical application of the CAC ECT gel, focusing on its safety, performance, and termination through doxycycline (Dox) administration in the eyes of healthy New Zealand White rabbits, as well as its therapeutic efficacy in rabbits with sodium iodate (SI)-induced retinal degeneration. The findings indicated that CAC ECT gel can be safely implanted without harming the retina or lens, displaying resistance to degradation, facilitating cell attachment, and secreting bioactive GDNF. Furthermore, the GDNF levels could be modulated by the number of implants. Moreover, Dox administration was effective in terminating gel function without causing retinal damage. Notably, rabbits with retinal degeneration treated with the gels exhibited significant functional recovery in both a-wave and b-wave amplitudes and showed remarkable efficacy in reducing photoreceptor apoptosis. Given its biocompatibility, mechanical stability, controlled drug release, terminability, and therapeutic effectiveness, our CAC ECT gel presents a promising therapeutic strategy for various retinal diseases in a clinical setting, eliminating the need for immunosuppressants.

Background: This study investigated the effect of indirect air-cooling on the variation in intrapulpal temperature (ΔT) during different light-curing protocols of bulk-fill resin composites in molars with class V cavities. Methods: A nonretentive class V cavity was prepared in an upper molar. The intrapulpal temperature changes with and without air-cooling were recorded with type K thermocouple. The cavity was restored with bulk-fill resin composites: Tetric PowerFlow and Filtek Bulk-Fill Flow. The tooth was exposed to different light-curing protocols (n=5) using the Valo Grand light-curing unit: (i) high-intensity light-curing of 3200 mW/cm² (3 and 6 s) and (ii) moderate-intensity light-curing of 1000 mW/cm² (10 and 20 s). The ΔT data were subjected to two-way ANOVA, followed by Bonferroni post hoc test. Results: A significant increase in temperature was observed with the use of the high-intensity light-curing resin composite without indirect air-cooling. In addition, the application of air-cooling significantly decreased the temperature in all the groups except for the Tetric PowerFlow bulk-fill resin composite at 3 s of light-curing. Conclusion: Indirect air-cooling resulted in a lower increase in intrapulpal temperature during the light-curing of bulk-fill resin composites, making it an effective alternative for controlling the temperature rise in class V restorations with 1 mm of remaining dentin.

This work investigated the influence of current density, plating solution flow rate, and nozzle outlet-cathode distance on the properties of Ni-diamond composite coatings. A multi-physics field simulation is employed to analyze the interplay between current density, plating solution flow rate, and nozzle outlet-cathode distance on the flow field and electric field distribution. Additionally, particle tracing simulations were incorporated into the model to evaluate the incorporation efficiency of diamond particles during composite electrodeposition. Experimental validation of the findings shows a significant increase in the diamond particle content of the coating. This combined approach provides valuable insights for optimizing the jet electrodeposition process for Ni-diamond composite coatings with superior properties.

The article presents the results of research on the production of effective inorganic fillers and chemically resistant composite polymer-mineral materials based on industrial waste. The aim of the work is to develop the technological foundations for the production of inorganic fillers and highly filled filling compositions for use in chlorine-containing media. Materials with high resistance to hydrochloric acid are graphite and quartz sand. Thermal power plant (TPP) ash was used as an acid-resistant filler in the compositions. The simplex lattice planning method was used to determine the areas of compositions with the best properties. Two components were selected: formaldehyde rubber resin and mineral filler (TPP ash) as a binder. As the third component, hydrolytically active fillers were used - anhydrite, phosphogypsum and phosphorus production slag. A preliminary operation was performed to remove hygroscopic moisture from the filler.The influence of the nature of mineral fillers on the chemical stability and durability of the obtained composites is investigated. The nature of the interaction of mineral fillers with a polymer binder was determined, and chemical interaction of the hydroxyl groups of the filler and the methyl groups of the polymer took place. The mathematical planning method was used to optimize the chemical resistance and durability of the compositions of the studied substances. Based on the results of this study, optimal compositions of compositions, anhydrite, phosphogypsum and phosphoric slag were selected. These composites, with the highest possible degree of filling, have high target characteristics.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

This paper delves into the application of digital twin monitoring techniques for enhancing offshore floating wind turbine performance, with a detailed case study. We explore the practical implementation of digital twins and their efficacy in optimizing operations and predictive maintenance. Our findings emphasize digital twins' potential as a valuable tool for renewable energy, driving efficiency and sustainability in offshore floating wind installations.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

This review provides a systematic analysis of the literature data on the electrodeposition of composite coatings using plating baths based on a new generation of room-temperature ionic liquids, known as deep eutectic solvents (DESs). Such systems offer several advantages over traditionally used aqueous electrolytes and organic solvent-based electrolytes. The colloidal-chemical properties of suspension and colloidal electrolytes for composite deposition are thoroughly examined. New theories describing the kinetics of co-deposition of composite layers are characterized. The kinetics and mechanism of electrochemical deposition processes of composite coatings with metallic matrices are discussed. Case studies regarding the electrodeposition of composite coatings based on electrodeposited copper, silver, zinc, tin, nickel, cobalt, and chromium from DES-assisted electroplating baths are described and systematized. The main prospective directions for further research in the discussed scientific area are highlighted.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

The two main strategies used in this study are the binary representation and the decomposition of a natural number into many compound functions of odd function and even function. The Collatz conjecture regarding odd even numbers in number theory can be examined and discussed using them in this way: The sequence created by the finite iterations of the Collatz function becomes the ultimately periodic sequence if any natural number is the beginning value, proving the conjecture that has been held for 85 years.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

Under batch experiment conditions, this work seeks to successfully remove Diclofenac-Na (DCF-Na) from an aqueous solution utilizing a composite sorbent made of Bentonite, Kaolinite clay, and Worm casting (BKW). This study investigated the structural modification of the H₃PO₄ Modified Clay by X-ray fluorescence and the effect of selected adsorption factors – DCF-Na concentration and modified BKW composite dosage. The concentration equilibrium data was used to study six isotherm models. Freundlich isotherm model better explained the adsorption of DCF-Na onto modified BKW composite with a correlation coefficient close to 1. Kinetics models were examined, and the Elovich model gave a better fit than other kinetic models studied. Mass diffusion mechanisms and thermodynamics studies were successfully carried out. The enthalpy change values evaluated were negative, which revealed the spontaneity of DCF-Na remediation onto modified BKW, and that DCF-Na adsorption is exothermic and occurred through a physisorption process.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

The aroused quest to reduce the delay at interconnect level is the main urge of this paper to come across a configuration of Carbon Nanotube (CNT) bundle namely squarely packed bundle of composite CNTs. The approach, demonstrated in this paper, adapts the composite bundle to adopt for high speed Very Large Scale Integration (VLSI) interconnect with technology sizing down. To reduce the delay of the proposed configuration of composite CNT bundle, the behavioral change of Resistance (R), Inductance (L) and Capacitance (C) has been observed with respect to both width of the bundle and diameter of the CNTs in the bundle. Consequently, the performance of the modified bundle configuration is compared with previously developed configuration namely squarely packed bundle of dimorphic MWCNTs in terms of propagation delay and crosstalk delay at local, semiglobal and global level interconnect. The proposed bundle configuration is ultimately enacted as better one for 32nmand 16nmtechnology node and suitable for 7nmas well.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

The paper presents a modified finite element method for nonlinear analysis of 2D beam structures. To take into account the influence of the shear flexibility, a Timoshenko beam element was adopted. The algorithm proposed enables using complex material laws without the need of implementing advanced constitutive models in finite element routines. The method is easy to implement in commonly available CAE software for linear analysis of beam structures. It allows to extend the functionality of these programs with material nonlinearities. By using the structure deformations, computed from the nodal displacements, and the presented here generalized nonlinear constitutive law, it is possible to iteratively reduce the bending, tensile and shear stiffnesses of the structures. By applying a beam model with a multi layered cross-section and generalized stresses and strains to obtain a representative constitutive law, it is easy to model not only the complex multi-material cross-sections, but also the advanced nonlinear constitutive laws (e.g. material softening in tension). The proposed method was implemented in the MATLAB environment, its performance was shown on the several numerical examples. The cross-sections such us a steel I-beam and a steel I-beam with a concrete encasement for different slenderness ratios were considered here. To verify the accuracy of the computations, all results are compared with the ones received from a commercial CAE software. The comparison reveals a good correlation between the reference model and the method proposed.

Silicone RTV-based engineering rubber composite products have been widely used for several applications in various fields as a major component such as structure, automotive, and medical. In its application, the rubber composite product is placed in an open area that is directly exposed to sunlight and rain. It has a significant negative impact on changes in chemical and rheological properties, making the product life of rubber composite products shorter. Therefore, in this study, changes in the chemical and rheological properties of both isotropic and anisotropic magnetorheological elastomer (MRE) treated with accelerated weathering were studied compared to untreated specimens with specimens that had been treated. MRE specimens with 40% by weight CIP were prepared with no current excitation and another sample were made under 1.5 T of magnetic flux density. Each specimen was treated in an accelerated weathering machine Q-Sun Xe-1 Xenon Test Chamber with a UV light exposure cycle for 102 minutes and 18 minutes of UV light combined with water spray for 24 hours followed by a condensation cycle of 4 hours in a dark period. Material characterization was carried out using FTIR and Rheometer to determine the changes in chemical and rheological properties. The morphological analysis results showed that the surface was rough and more cavities occurred after being given weather treatment. Rheometer test results showed a decrease in storage modulus in each MRE specimen that had been treated compared to untreated MRE specimens. Meanwhile, FTIR testing showed a change in wave peak between untreated and treated MRE specimens.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

Based on a modified dice-and-fill technique, a PIN-PMN-PT single crystal 1-3 composite with the kerf of 12 μm and pitch of 50 μm was prepared. The as-made piezoelectric composite material behaved with high piezoelectric constant (d33 = 1500 pC/N), high electromechanical coefficient (kt = 0.81), and low acoustic impedance (16.2 Mrayls). Using lithography and flexible circuit method, a 48-element phased array was successfully fabricated from such a piezoelectric composite. The array element was measured to have a central frequency of 20 MHz and a fractional bandwidth of approximately 77% at −6 dB. Of particular significance was that this PIN-PMN-PT single crystal 1-3 composite-based phased array exhibits a superior insertion loss compared with PMN-PT single crystal and PZT-5H-based 20 MHz phased arrays. The focusing and steering capabilities of the obtained phased array were demonstrated theoretically and experimentally. These promising results indicate that the PIN-PMN-PT single crystal 1-3 composite-based high frequency phased array is a good candidate for ultrasound imaging applications.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

The effects of the additives (silicon carbide and titania) and sintering temperatures on the phases developed, physical and mechanical properties of sintered mullite-carbon ceramic composite produced from kaolin and graphite was investigated. The kaolin and graphite of known mineralogical composition were thoroughly blended with 5 and 3 (vol.) % silicon carbide and titania respectively. From the homogeneous mixture of kaolin, graphite and titania, standard samples were prepared via uniaxial compaction. The test samples produced were subjected to firing (sintering) at 1300˚C, 1400˚C and 1500˚C. The sintered samples were characterized for the developed phases using x‐ray diffractometry analysis, microstructural morphology using ultra‐high resolution field emission scanning electron microscope (UHRFEGSEM). Various physical and mechanical properties were determined. It was observed that the addition of SiC/TiO2 additives to the samples made them to possess very low oxidation indices .This also resulted in improvement in the bulk densities and cold crushing strength of the sample when compared with those without additives. It was concluded that the addition of SiC/TiO2 additives improves on the high temperature oxidation resistance of the mullite-carbon ceramic composite sample.

Additive Manufacturing (AM) methods are increasingly beign abopted in the industry as an alternative for mass production. In particular, Fused Deposition Modeling (FDM) technology is leading the way in this field. However, the adhesion of layers in products produced using FDM technology is an important issue. These products are particularly vulnerable to forces acting parallel to the layers and specially to impact strength. This study aims to optimize the impact strength against loads acting parallel to the layers (ZX orientation) of PA6, one of the most widely used materials in the industry. This orientation is critical in term of mechanical properties, and the mechanical characteristics are significantly lower compared to other orientation. In this study, filaments containing pure PA6 with 15% short carbon fiber and 30% glass fiber were utilized. Additionally, printing temperature, layer thickness and heat treatment duration were used as independent variables. An L9 orthogonal array was employed in this study, and each experiment was repeated three times to conduct impact strength tests. Characterization, Taguchi optimization, a factor analyses were performed, followed by fracture surface characterization by SEM. As a result, the highest impact strength was achieved with pure PA6 at 8.9 kJ/m2, followed by PA6 GF30 at 8.1 kJ/m2 and the lowest impact strength was obtained with PA6 CF15 at 6.258 kJ/m2. When compared to the literature and manufacturer datasheets, it was concluded that the impact strength values have significantly increased, and the chosen experimental factors and their levels, particularly nozzle temperature, were effective.

This study explores the development and characterization of ceramic rod reinforced TWIP (Twinning Induced Plasticity) steel matrix composites, fabricated using a lost foam casting process. The incorporation of ceramic rods aims to enhance the mechanical properties of TWIP steel, which is known for its excellent plasticity. Mechanical testing demonstrated a significant improvement in flexural strength and ductility, with the composite exhibiting over double the strength of the unreinforced TWIP steel. Heat treatment at 500°C for 60 minutes further enhanced these properties, increasing the composite's flexural strength to 1023 MPa and improving its ductility. The observed improvements are attributed to the synergistic effects of the hard ceramic reinforcement and the ductile matrix, as well as the microstructural modification conferred by heat treatment. These findings suggest that ceramic rod reinforced TWIP steel composites are promising materials for applications requiring a combination of high strength and ductility.

The calculation of the global shear capacity of steel-concrete composite downstand cellular beams with precast hollow-core units is important as it affects the span to depth ratios and the amount of material used, hence affects the embodied CO2 calculation when designers are deciding on the floor grids. This paper presents a reliable tool that can be used by designers to alter and optimise grip options during the preliminary design stages, without the need to run onerous calculations. The global shear capacity prediction formula is developed using five machine learning models. First, a finite element model database is developed. The influence of the opening diameter, web opening spacing, tee-section height, concrete topping thickness, the interaction degree, and the number of shear studs above the web opening are investigated. Reliability analysis is conducted to assess the design method and propose new partial safety factors. The Catboost Regressor algorithm presented better accuracy compared to the other algorithms. An equation to predict the shear capacity of composite cellular beams with hollow-core units is proposed by Gene Expression Programming. In general, the partial safety factor for resistance, according to the reliability analysis, varied between 1.25 and 1.26.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

The purpose of this research work was to synthesis bio-derived nanocomposite films by incorporating Na0.5Bi0.5TiO3 (NBT) nanoparticles into Chitosan matrix. The NBT nanoparticles were synthesized using a traditional solid-state technique. Then, through a solution casting approach, flexible composite films were fabricated using Chitosan polymer. The morphology and structural assessments were carried out utilizing scanning electron microscopy (SEM), X-ray diffraction and fourier transform infrared technique. The SEM micrographs showed that NBT nanoparticles were randomly distributed and interconnected with other particles, forming interconnected grains with substantial interspaces within the matrix. The spectral response between 300 and 800 nm of the composites is mainly governed by light scattering of NBT particles with diameter sizes in the 100 - 400 nm range and the bandgap of the NBT phase. The dielectric studies demonstrated that the composite films exhibited higher dielectric values compared to the pure Chitosan film. Besides, the increase of NBT amount was found to increase the dielectric values. Additionally, local piezoelectric measurements reveal the expected piezoelectric and ferroelectric behavior for the NBT particles dispersed into the polymer matrix, as locally probed by Piezoresponse Force Microscopy. The studied system bears interest for advanced biocompatible opto- and piezo-electric materials.

In response to the growing demand for high-strength and high-toughness materials in industries like aerospace and automobiles, there is a need for metal matrix composites (MMCs) that can simultaneously enhance strength and toughness. This paper focuses on the design configurations of MMCs, which include both the configurations resulting from reinforcements and the inherent heterogeneity of the matrix itself. The mechanical properties of MMCs are influenced by factors such as reinforcement content, shape, size, and spatial distribution within the composite architecture. Among them, Aluminum matrix composites (AMCs) are particularly significant in aerospace, electronics, and electric vehicles due to their potential for weight reduction and enhanced performance. However, the challenge lies in the inverse relationship between strength and toughness, hindering the widespread utilization and large-scale development of MMCs. The design configuration of composites plays a critical role in achieving concurrent improvements in strength and toughness. This review explores the advantages of toughness, toughening mechanisms, reinforcement distribution characteristics, and structural parameters in the design of composite architectures. Drawing inspiration from biological composites like bone, the development of synthetic composites with homogeneous structural designs provides insights into attaining exceptional strength and toughness in lightweight engineering structures. Additionally, understanding fracture behavior and toughening mechanisms in heterogeneous nanostructures is vital for advancing the field of metal matrix composites. Summarily, the design of composite architectures holds tremendous potential for tailoring AMCs with outstanding strength and toughness, addressing the requirements of lightweight engineering structures in various industries.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Arthroplasty is commonly performed to treat advanced osteoarthritis or other degenerative joint conditions, but it can also be considered for young patients with severe joint damage that significantly limits their functionality and quality of life. Young patients are still at risk of aseptic mobilization and bone resorption due to the phenomenon of stress-shielding that causes an uneven distribution of tensions along the femoral contact surface prosthesis. This phenomenon can be limited by appropriately choosing the material of the prosthesis or by varying its stiffness, making sure that its mechanical behavior simulates that of the femur as much as possible. The aim of this study is to evaluate the mechanical behavior of a prosthesis optimized both in shape and material and in comparing the results with a standard titanium prosthesis. Methods: Through three-dimensional modeling and the use of software finite element method (FEM) such as ANSYS we simulate the mechanical behavior of traditional prosthesis and prosthesis optimized topologically respecting the ASTM F2996-13 standard Results: With topological optimization there is a stress reduction from 987 Mpa to 810 Mpa with a mass reduction of 30%. With the use of carbon fiber, it is possible to further reduce stress to 509 Mpa. Conclusions: The reduction of stress on the femoral stem allows an optimal distribution of the load on the cortical bone thus decreasing the problem of stress-shielding.

The presented research focused on the evaluation of the novel concept of overmolding technique using self-reinforced composite prepregs and recycled polymer blends. In order to evaluate the effectiveness of the proposed manufacturing technique, several series of materials based on polycarbonate/polyethylene terephthalate (PC/PET) and polycarbonate/polyethylene terephthalate glycol (PC/PETG) blends were prepared. The reinforcing component in the form of overmolded prepreg was made from polyester-based self-reinforced composite (srPET). The prepared materials were compared in terms of mechanical properties and heat resistance; the study was supplemented by thermal analysis measurements (DMTA, DSC). Considering the mechanical characteristics, the overmolding technique turns out to be an effective method of improving the properties of composites, and the increase in impact strength turns out to be particularly beneficial. The increase of the impact strength for overmolded PC/PET blend reached 430 % for PC/PETG sample 330% , while for PC-based composite, only 100%. The expected improvement in thermomechanical properties turned out to be difficult to achieve due to the rapid softening of the srPET prepreg at around 70 °C. However, technological tests and analysis of properties clearly indicated that the use of PC-based blends makes it possible to create a permanent connection with reinforcement based on srPET prepregs, which can significantly expand the potential of applications of this type of materials.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

The paper describes the research findings on dynamic and mechanical properties of composite elastomers with high permeability magnetic filling agent capable of rapidly and reversibly changing its properties when exposed to an external magnetic field, which makes it a perspective material for application in a wide range of engineering areas. The research has analyzed the trends in the strength properties of the materials obtained through the use of filling agents of different fineness, content, and structural organization in the final polymer, under different conditions. This allowed to obtain the correlations between the influence of the filler's relative fineness on the dynamic and mechanical properties of composite polymers, and to estimate the trends in the parameters describing the material strength under the complex magnetic and thermal influence. The results obtained by the authors allowed to ground the composition and structural organization of the final material with the best set of dynamic and mechanical properties.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

As the aileron mass parameter and its position on the velocity and frequency of the flutter is an important problem in design of the aircraft wings, the optimization of the composite wing with an aileron is represented in this paper. Mass properties and its distribution have a great influence on the multi-disciplinary optimization procedure based on speed and frequency of flutter. At first, flutter speed was obtained with and without aileron, then aileron was mass-equilibrated and other studies were performed using the proposed method. It is deduced that changing the position and mass properties of the aileron the speed and frequency of the flutter changed. The position of the aileron was determined for better wing performance in flutter instability and minimizing the composite stress. In the present study, it has been attempted to model the aerodynamics of the problem under ultrasound with the panel method, and the structure has been modeled using finite element method and coupled with the aerodynamics. Using the p-k method, the equations are solved and the results are extracted.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.