We demonstrate a multi-purpose plasmonic sensor based on nanovoid array fabricated via inexpensive and highly reproducible direct femtosecond laser patterning of thin glass-supported Au films. The proposed nanovoid array exhibits near-IR surface plasmon (SP) resonances, which can be excited under normal incidence and optimised for specific application by tailoring array periodicity as well as nanovoid geometric shape. Fabricated SP sensor offers competitive sensitivity of about 1600 nm/RIU at a figure of merit of 12 in bulk refractive index tests, as well as allows for identification of gases and ultra-thin analyte layers making the sensor particularly useful for common bioassay experiments. Moreover, isolated nanovoids support strong electromagnetic field enhancement at lattice SP resonance wavelength, allowing for label-free molecular identification via surface-enhanced vibration spectroscopy.

A real-time two-way direct load control (TWDLC) of central air-conditioning chillers in wide area is proposed to provide demand response. The proposed TWDLC scheme is designed to optimize the load shedding ratio of every customer under control to ensure the target load to be shed is met at every scheduling period. In order to overcome the load reduction uncertainties of TWDLC, an innovative solution is proposed by applying a certain degree of loosening on the constraint of the actual shed load. Fuzzy linear programming is utilized to solve the optimization problem with fuzzy constraints. The proposed fuzzy linear programming problem is solved by delicately transforming it into a regular liner programming problem. A selection scheme used to obtain the feasible candidates set for load shedding at every sampling interval of TWDLC is also designed along with the fuzzy linear programming.

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

Stability studies remain a crucial aspect of power systems dynamic analysis, and are typically explored in three main categories: numerical methods, linearization techniques, or direct methods, which utilize Lyapunov energy functions. This paper belongs to the third category, and highlights the usefulness of the Popov stability criterion in the analysis of nonlinear power system models. The main advantage of this criterion is that it provides conditions for global asymptotic stability of an equilibrium point, for a nonlinear dynamic system. We show a general method to apply this stability criterion, and examine its uses in several specific applications and case-studies. The results are demonstrated by analyzing the stability of a system that includes a grid-connected storage device and a renewable energy source.

Automatic and blind parameter estimation based on the inherent features of wireless signals is a major research area due to the fact that these techniques lead to the simplification of receivers, especially in terms of coarse synchronization, more importantly reduce down the signaling load at the control channels. Thus, in the literature many techniques are proposed to estimate a vast set of parameters including modulation types and orders, data and chip rates, phase and frequency offsets and so on. In this paper, a cyclostationary feature detection based method is proposed to estimate the carrier numbers and carrier spacing of carrier-aggregated direct sequence spread spectrum cellular signals blindly. The particular chip rate of the signal is also estimated through the process jointly. In the paper, after the proposed method is formulated, the measurement setup which is developed to collect the data for the validation of the proposed method is introduced. The measurement results are post-processed for performance analysis purposes. To that end, the method is investigated in terms of SNR values, different channel conditions, and measurement durations. Furthermore, the performance of the proposed method is compared with that of energy detection. Measurement results indicate superior performance of the proposed method under significant wireless channel impairments and in low-SNR regions.

Breast cancer in patients with prior breast augmentation poses unique challenges for detection, diagnosis, and management. Mastectomy rates are increasing, and patients with prior augmen-tation often have a lower body mass index, making autologous techniques unsuitable. This study aims to assess the best reconstructive option in patients with a history of subglandular or dual plane breast augmentation. Materials and methods: a prospective analysis was conducted on pa-tients who underwent breast reconstruction after mastectomy. Patients with subglandular or dual plane breast augmentation were included. Patients were divided into submuscular breast recon-struction (group 2) or prepectoral breast reconstruction (group 1) groups. Demographic and sur-gical data were collected. Results: A total of 47 patients were included, with 23 in Group 1 and 24 in the Group 2. Complications occurred in 11 patients (23.4%), with significant differences be-tween groups. The most common complication was seroma formation. Implant loss occurred in 4.3% of cases in the Group 1, while no implant loss was observed in the Group 2. Patient-reported satisfaction scores were similar between groups at 12 months postoperatively. Conclusions: sub-pectoral breast reconstruction with a tissue expander seems a safer and effective technique for pa-tients with prior breast augmentation. It resulted in fewer complications. This approach should be considered as an option for breast reconstruction after mastectomy in this cohort of patients.

The use of braces equipped with dissipative devices for the seismic strengthening of seismically prone reinforced concrete frames is among the most widespread methods, as it allows for high reductions in seismic vulnerability with inexpensive, quickly executed interventions, which can often be carried out mainly by the exterior, resulting in interruptions of use limited both in time and to only small portions of the building. The design methods of dissipative devices are based on the extensive use of pushover analyses capable of highlighting the structural deficiencies of the building and comparing the performances achievable by developing designs according to different methods and sizing criteria. In the present work, with reference to a case study represented by a four-story spatial frame having characteristics representative of design and construction common practice of the 1970s in Southern European countries, the performance of three different design methods is compared. The examined procedures differ for: methods for estimating the peak displacement response of the nonlinear systems, namely the well-known Equal Displacement Rule and the Equivalent (secant) stiffness and Damping rule; and criteria for distributing stiffness and strength of the bracing along the height, namely the distribution of stiffness and strength proportionally to those of the frame, and methods that vary the stiffness and strength along the height in order to minimize the eventual irregularity in elevation of the bare frame. The effectiveness of the procedures is checked by static pushover analysis and nonlinear response history analysis, performed by unidirectional and bidirectional input. Pros and cons of each procedure are summarized, all of them able to provide bracing designs that meet the performance requirements set during the design phase.

Once considered relatively benign, superficial vein thrombosis (SVT) of the lower limbs is often linked to deep vein thrombosis (DVT) or pulmonary embolism (PE). Treatment goals include alleviating local symptoms and preventing SVT from recurring or extending into DVT or PE. Fondaparinux 2.5 mg once daily for 45 days is the treatment of choice for most patients with SVT. Potential alternatives include intermediate-dose low-molecular-weight heparin or the direct oral factor Xa inhibitor rivaroxaban. Despite these treatment options, significant gaps remain, including the role of systemic or topical anti-inflammatory agents alone or combined with anticoagulants, and the optimal duration of anticoagulation for patients at varying risk levels. Additionally, the efficacy and safety of factor Xa inhibitors other than rivaroxaban, management of upper extremity SVT, and optimal treatment for SVT near the sapheno-femoral or sapheno-popliteal junctions are not well understood. This narrative review aims to summarize current evidence on anticoagulant treatment for SVT, highlight key unmet needs in current approaches, and discuss how ongoing studies may address these gaps.

The energy transition is a challenge that affects all sectors, from transport to civil structures and industry. In the industrial sector, the greatest need is the decarbonisation of energy-intensive in-dustries, such as producers of iron and steel, aluminum, cement, petrochemicals, paper, and more. The steel industry, in particular, is a hard-to-abate high-emissivity industry that, due to chemical processes and high thermal demands (often above 500 °C), contributed to 7.4% of global CO2 emissions in 2021. This paper explores the potential applications of hydrogen in these hard-to-abate sectors, highlighting its versatility and significance in decarbonization efforts, especially as a me-dium to facilitate the transition to green electric energy uses. It provides an overview of hydrogen production methods, emphasizing the importance of sustainable and green hydrogen production. It reviews hydrogen production methods, storage, and potential in blended combustion. In the final part of the article, some considerations are introduced on the possible role of hydrogen in the steel sector (both as a supplementary fuel and as a reducing agent in innovative processes), showing that while there is potential for its inclusion as an element for decarbonization, it is necessary to carefully evaluate the energy balances of the various processes and the methods of hydrogen production, in order to avoid achieving only marginal effects.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

The conjugation of phytosterols (PSs) with fatty acids results in producing phytosterol esters (PSEs) characterized with enhanced lipophilicity and improved functional properties of major interest in food and nutraceutical applications. The use of immobilized lipases to catalyze direct transesterification reactions between PSs and plant oils to form PSEs as a green alternative to conventional chemical production methods has attracted interest during the last two decades. The low solubility of PSs in common plant oil triglycerides, typically below 3% at ambient temperatures, remains the main challenge for bringing lipase-catalyzed direct transesterification reactions of PSs and oil triglycerides to commercial scales. This study focuses on the enzymatic synthesis of PSEs starting from solubilized PSs at concentrations of up to 30% wt./wt. of oil mixtures comprising fatty acid ethyl esters (FAEEs), monoglycerides (MGs), diglycerides (DGs) and triglycerides (TGs) as a homogeneous medium for the direct transesterification reaction. The results of this study show for the first time that the addition of FAEEs into the reaction medium results in altering of the substrate preference of the enzyme making MGs as the favorite fatty acyl group donors for PSs amongst all other fatty acyl donors present in the reaction system. The proposed new enzymatic route allows starting with high concentrations of solubilized PSs making the direct transesterification of oil glycerides attractive for production of PSEs at industrials scales.

New families of direct serendipity and direct mixed finite elements on general planar, strictly convex polygons were recently defined by the authors. The finite elements of index r are H1 and H(div) conforming, respectively, and approximate optimally to order r+1 while using the minimal number of degrees of freedom. The shape function space consists of the full set of polynomials defined directly on the element and augmented with a space of supplemental functions. The supplemental functions were constructed as rational functions, which can be difficult to integrate accurately using numerical quadrature rules when the index is high. This can result in a loss of accuracy in certain cases. In this work, we propose alternative ways to construct the supplemental functions on the element as continuous piecewise polynomials. One approach results in supplemental functions that are in Hp for any p≥1. We prove the optimal approximation property for these new finite elements. We also perform numerical tests on them, comparing results for the original supplemental functions and the various alternatives. The new piecewise polynomial supplements can be integrated accurately, and therefore show better robustness with respect to the underlying meshes used.

Direct femtosecond laser writing or inscription is a useful technique, and it has been 1 employed to engineer various materials in many applications including nonlinear photonic crystals, 2 which are of periodically patterned second-order nonlinearity to get and control the coherent light at 3 new frequencies. By manipulation of second-order nonlinearity, either erased or poled, quasi-phase 4 matching has been achieved in several crystals, especially three-dimensional nonlinear photonic 5 crystals have been originally proposed and proved to be truly three-dimensional. Here we shortly 6 review on the recent advances in the research field of nonlinear photonic crystals inscribed by 7 femtosecond laser. We also discuss some phenomena that not understood yet and the future possible research topics in this field.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

The matrix converter converts the input line voltage into a variable voltage with an unrestricted output frequency without using an intermediate circuit, dc link circuit. A pure sine in and pure sine out is the unique feature of the matrix converter. This research paper also analyzes the basic operating principle and the simulation modeling of the direct matrix converter, which is controlled by the Space Vector Pulse Width Modulation technique by using the software which is known as MATLAB/Simulink. The most desirable features in the power frequency changes can be fulfilled by using the matrix converters, and this is the reason for the tremendous interest in the topology. Since the power electronic circuits which is known as the motor drives are used to operate the AC motors at the frequencies other than that of the supply.

Aphasia is one of the most socially disabling post-stroke deficits. Although traditional therapies have been shown to induce adequate clinical improvement, aphasic symptoms often persist. Therefore, new rehabilitation techniques which act as a substitute or as an adjunct to traditional approaches are urgently needed. The present review provides an overview of the efficacy and safety of the most innovative approaches which have been proposed over the last twenty years. First, we examined the effectiveness of the pharmacological approach, principally used as an adjunct to language therapy, reporting the mechanism of action of each single drug for the recovery of aphasia. Results are conflicting but promising. Secondly, we discussed the application of Virtual Reality (VR) which has been proved to be useful since it potentiates the ecological validity of the language therapy by using virtual contexts which simulate real-life everyday contexts. Finally, we focused on the use of Transcranial Direct Current Stimulation (tDCS), both discussing its applications at the cortical level and highlighting a new perspective, which considers the possibility to extend the use of tDCS over the motor regions. Although the review revels an extraordinary variability among the different studies, substantial agreement has been reached on some general principles, such as the necessity to consider tDCS only as an adjunct to traditional language therapy.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

This panel study investigates the relationship between green logistics indices, economic, environmental, and social factors in the perspective of Asian emerging economies. This study adopted FMOLS and DOLS methods to test research hypothesis, catering the problem of endogenity and serial correlation. The results suggest that logistics operations, particularly LPI2 (efficiency of customs clearance processes), LPI4 (quality of logistics services) and LPI5 (trade and transport-related infrastructure), are positively and significantly correlated with per capita income, manufacturing value added and trade openness. While, greater logistics operations are negatively associated with social and environmental problems including, climate change, global warming, carbon emissions, and poisoning atmosphere. In addition, human health is badly affected by heavy smog, acid rainfall, and water pollution. The findings further extend and reveal that political instability, natural disaster and terrorism are also a primary cause of poor economic growth and environmental sustainability with poor trade and logistics infrastructure. Further, the application of renewable energy resources and green practices can mitigate negative effects on social and environmental sustainability without compromising the performance of economic growth. There is very limited empirical work presented in literature using renewable energy and green ideology to solve macro-level social and environmental problems, while this study will assist the policymakers and researchers to understand the importance of green concept in improving countries’ social, economic and environmental performance.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

In order to enhance the efficiency of direct absorption solar collectors, this study carried out an experimental analysis about the optical and photothermal conversion performance of Fe3O4, ATO and Fe3O4/ATO nanofluids with total concentration of 0.1wt%. According to the results of experiments, Fe3O4 nanofluid outperform ATO nanofluid in terms of optical absorption; nevertheless, at wavelengths shorter than 600 nm, it also shows significant scattering reflection. The solar-weighted absorption coefficient of Fe3O4/ATO nanofluid rose from 0.863 (mFe3O4mTotal= 0.2) to 0.932 (mFe3O4mTotal= 0.8) when the optical path length increased from 0.01 m to 0.06 m. Additionally, the photothermal conversion efficiency of Fe3O4/ATO hybrid nanofluid was attained 0.932 at (mFe3O4mTotal= 0.2), above the 0.892 and 0.898 photothermal conversion efficiencies recorded for 0.1 wt% ATO and Fe3O4 nanofluids, respectively. When present together, the opposing optical characteristics of Fe3O4 and ATO boost photothermal conversion performance, which is anticipated to raise the efficiency of direct absorption solar collectors.

Graph query languages such as Cypher are widely adopted to match and retrieve data in a graph representation, due to their ability of retrieving and transforming information. Despite the most natural way to match and transform information is through rewriting rules, those are scarcely or partially adopted in graph query languages. Their inability of doing so has a major impact on the subsequent way the information is structured, as it might then appear more natural to provide major constraint over the data representation so to consequently constraint the way the information should be represented. On the other hand, recent works are starting to move towards an opposite direction, as the provision of a truly general semistructured model (GSM) allows to both represent all the available data formats (Network-Based, Relational, and Semistructured) as well as support an holistic query language expressing all major queries in such languages. In this paper, we show that the usage of GSM enables the definition of a general rewriting mechanism which can be expressed in current graph query languages only at the cost of adhering the query to the specificity of the underlying data representation. We formalise the proposed query language in terms graph rewriting mechanisms described as a set of production rules $L\to R$ while providing restriction to the characterization of L, while extending it to support structural graph nesting operations, useful to aggregate similar information around an entry-point of interest. We discuss how GSM, by fully supporting index-based data representation, allows for a better physical model implementation leveraging the benefits of columnar database storages. Preliminary benchmarks shows the scalability of this proposed implementation in comparison with state-of-the-art implementations.

Background & Objective: Acne Vulgaris is a common skin disease, with 5 % prevalence in Pakistan and has a significant physiological, psychological, emotional and social impact on the population, our study aims to estimate its annual economic burden per person in Pakistan.Methodology: Economic burden was estimated by using Cost of Illness analysis. All types of costs, including direct medication costs, direct non-medical costs and indirect costs due to loss of work. Data were collected from online databases and literature reviews. Results: Cost of illness analysis estimated that the cost of Acne Vulgaris treatment varies for mild, Moderate and severe acne. Acne is causing an annual economic burden of PKR 1,92,366 PKR per person (direct cost is PKR 1,86,366 and indirect cost 6,000) for an expensive treatment and PKR 53,550 (direct cost is PKR 47550 and indirect cost 6,000) for a cheap treatment. Limitation: Being an LMIC, Pakistan needs extensive study on the pharmacoeconomic analysis of Acne for proper and rational allocation of resources. Conclusion: Acne has a significant economic burden in Pakistan. Even with significant impact of Acne, there is very minute work done about Acne in Pakistan.

The fuel cell particularly the Proton Exchange Membrane Fuel Cell (PEMFC) is a new energy technology that plays a critical role in achieving market viability. The PEMFC has high power density, zero CO₂ emissions, and high conversion efficiency. However, with uniform distribution of fuel in PEMFC, we can improve the performance and reduce the cost. The PEMFC will be more efficient and effective in terms of renewable energy as a byproduct only water. Metal foam is used as an alternative for the channels in PEMFC. The model of PEMFC was established by using the ANSYS Fluent 3D Model. Then we proposed four configurations of PEMFC. The outcome demonstrates that Case IV provided outstanding performance if it is compared with the other three cases. In terms of power density, Case IV provided a high power density that is double that of Case I. The porosity of metal foam was investigated. The 0.6 porosity value is found as the optimal value. The uniform distribution of the fuel can be achieved at this value which leads to the outstanding current density.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

The study presents an efficient computational investigation on the behaviour of the direct-drive system integrated into the offshore 5MW NREL wind turbine model under demanding aerodynamic loading conditions with the aim of optimising and developing more sustainable key structural components. The research was based on computational simulation packages to verify the use of real-world wind data, the loading conditions on the blade structures through aero-elastic simulation studies, as well as analyse the behaviour of the drive system. Through the application of validated aerodynamic loading conditions, resulting normal forces on the blades structure were obtained and applied to a dedicated simplified model that was also previously validated, to estimate the transferred loads into the powertrain. The adopted methodology allowed for the identification of shaft misalignment induced air-gap eccentricity. The impact of shaft deflections on resulting magnetomotive force was considered by making use of the Maxwell stress distribution expression. By taking into account the resulting loading cases on the generator structure, as well as the inherent typical loads generated by the electrical machine, a procedure including structural parametric and topology optimisation was developed and performed, achieving a rotor mass reduction between 8.5 and 9.6% if compared with the original model.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

Recent advance in electric propulsion systems have demonstrated that these engines can be used for for long-duration interplanetary voyages. Constant specific impulse engine described as a thrust-limited engine is an example of this type of engine, processing the ability to operate at a constant level of impulse. The determination of minimum-fuel, planar heliocentric Earth-to-Mars low-thrust trajectories of spacecraft using a constant specific impulse is discussed considering the first-order necessary conditions derived from Lawden’s primer vector theory. The minimum-fuel low-thrust Earth-to-Mars optimization problem is then solved in two-dimensional, heliocentric frame using both indirect and direct methods. In the indirect method, two-point-boundary-value problems are derived to solve boundary value problems for ordinary differential equations. In the direct method, a general-purpose optimal control software called GPOPS-II is adopted to solve these optimal control problems. Numerical examples using two different optimization methods are presented to demonstrate the characteristics of minimum-fuel planar low-thrust trajectories with on-off-on thrust sequences at three chosen flight times and available maximum powers. The results are useful for broad trajectory search in the preliminary phase of mission designs.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

In chronic hepatitis C (CHC) patients, interferon-based treatments showed toxicity, limited efficacy, and psychiatric manifestations. Direct-acting antiviral (DAA) agents appeared safer, though it remains unclear if they may exacerbate or foster mood symptoms in drug-naïve CHC patients. We evaluated 62 CHC patients’ mental status, before and 12 weeks after DAA therapy, by assessment scales and psychometric instruments. We subdivided patients into two groups, CHC patients with (Group A) or without (Group B) a current and/or past psychiatric history. After DAA treatment, Group A patients showed low anxiety and improved depression, no variation in self-report distress, but worse general health perceptions. No significant difference emerged from coping strategies. Depression and anxiety improved in Group B, and no change emerged from total self-reported distress, except for somatization. Moreover, Group B increased problem-focused strategies for suppression of competing activities, and decreased strategies of instrumental social support. Contrarily, Group B reduced significantly emotion-focused strategies, such as acceptance and mental disengagement, and improved vitality, physical and social role functioning. DAA therapy is safe and free of hepatological and psychiatric side effects in CHC patients, regardless of current and/or past psychiatric history. In particular, patients without a psychiatric history also remarkably improved their quality of life.

Purpose: Dysarthria, a neurological injury of the motor component of the speech circuitry, is of common consequences of traumatic brain injury (TBI). Palilalia is a speech disorder characterized by involuntary repetition of words, phrases, or sentences. Based on the evidence supporting the effectiveness of transcranial direct current stimulation (tDCS) in some speech and language disorders, we hypothesized that using tDCS would enhances the effectiveness of speech therapy in a client with chronic dysarthria following TBI. Method: We applied the constructs of the “Be Clear” protocol, a relatively new approach in speech therapy in dysarthria, together with tDCS on a chronic subject who affected by dysarthria and palilalia after TBI. Since there was no research on the use of tDCS in such cases, regions of interest (ROIs) were identified based on deviant brain electrophysiological patterns in speech tasks and resting state compared with normal expected patterns using the Quantitative Electroencephalography (QEEG) analysis. Results: Measures of perceptual assessments of intelligibility, an important index in the assessment of dysarthria, ​​were superior to the primary protocol results immediately and 4 months after intervention. We did not find any factor other than the use of tDCS to justify this superiority. The percentage of repeated words, an index in palilalia assessment, had a remarkable improvement immediately after intervention but fell somewhat after 4 months. We justified this case with subcortical origins of palilalia. Conclusion: Our present case-based findings suggested that applying tDCS together with speech therapy may improve intelligibility in similar case profiles as compared to traditional speech therapy. To reconfirm the effectiveness of the above approach in cases with dysarthria following TBI, more investigation need to be pursued.

We report an easy-to-implement device for SERS-based detection of various analytes dissolved in water droplets at trace concentrations. The device combines an analyte-enrichment system and SERS-active sensor site, both produced via inexpensive and high-performance direct fs-laser printing. Fabricated on a surface of water-repellent polytetrafluoroethylene substrate as an arrangement of micropillars, the analyte-enrichment system supports evaporating water droplet in the Cassie-Baxter superhydrophobic state, thus ensuring delivery of the dissolved analyte molecules towards the hydrophilic SERS-active site. The efficient pre-concentration of the analyte onto the sensor site based on densely-arranged spiky plasmonic nanotextures results in its subsequent label-free identification by means of SERS spectroscopy. Using the proposed device, we demonstrate reliable SERS-based fingerprinting of various analytes, including common organic dyes and medical drugs at ppb concentrations. The proposed device is believed to find applications in various areas, including label-free environmental monitoring, medical diagnostics, and forensics.

Genetic testing has expanded out of the research laboratory into medical practice and the direct-to-consumer market, and rapid analysis of the resulting genotype data can now have significant impact. We present a method for summarizing personal genotypes as ‘genotype fingerprints’ that meet these needs. Genotype fingerprints can be derived from any single nucleotide polymorphism (SNP)-based assay, and remain comparable as chip designs evolve to higher marker densities. We demonstrate that they support distinguishing types of relationships among closely related individuals and closely related individuals from individuals from the same background population, as well as high-throughput identification of identical genotypes, individuals in known background populations, and de novo separation of subpopulations within a large cohort through extremely rapid comparisons. While fingerprints do not preserve anonymity, they provide a useful degree of privacy by summarizing a genotype in a way that prevents reconstruction of individual marker states. Genotype fingerprints are therefore well-suited as a format for public aggregation of genetic information to support ancestry and relatedness determination without revealing personal health risk status.

Manipulation of micro- and nano-sized objects with optical tweezers is a well established, albeit still evolving technique. While many objects can be trapped directly with focused laser beam(s), for some applications indirect manipulation with tweezers-operated tools is preferred. We introduce a simple, versatile micro-tool operated with holographic optical tweezers. The 40 µm long dumbbell-shaped tool, fabricated with two-photon laser 3D photolithography has two beads for efficient optical trapping and a probing spike on one end. We demonstrate fluids viscosity measurements and vibration detection as examples of possible applications.

Through the integration of high-resolution hydrodynamic modeling and comprehensive field measurements, this study elucidates the intricate three-dimensional hydrographic characteristics of the eastern Gulf of Thailand (eGOT). In addition to the prevalent tidal currents dictating alternating flow along the northwestern and southeastern axes, our investigation reveals pronounced seasonal variations in mean currents, water temperature, and salinity within the eGOT, closely linked to the dynamics of the Asian-Australian monsoon system. During the southwest monsoon, mean currents exhibit a southeasterly trend, contrasting with a northwesterly pattern during the northeast monsoon. Lowest water temperatures occur during the latter, while the highest levels are observed during the 1st monsoon transition (April-March). Notably, salinity levels reach their lowest levels during the southwest monsoon and the 2nd monsoon transition (October), coinciding with the seasonal stratification of the water column and the emergence of a distinct stable along-the-shore northwesterly current with the average speed of 15 cm/s, defined here as the “Chathaburi Coastal Current (CCC)”. Model experiments attribute the formation of the CCC to decreased salinity induced by direct rainfall, highlighting the significance of rainfall as a key factor influencing coastal water dynamics in tropical regions or areas experiencing high precipitation.

Body-centered cubic bismuth (Bi) is considered an enticing pressure marker, and therefore it is highly desirable to command its accurate equation of state (EOS). However, significant discrepancies are noted among the previous experimental EOSs. In the present work, the EOS up to 300 GPa is theoretically obtained by direct solving the partition function via a direct integral approach (DIA). The calculated results nearly reproduce the hydrostatic experimental measurements below 75 GPa, and the deviations from the measurements gradually get larger with increasing pressure. Based on the ensemble theory of equilibrium state, DIA works with high precision particularly in high-pressure conditions, so the hydrostatic EOS presented in this work is expected to be a reliable pressure standard.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

This paper introduces new improvements to the modified version of the BIRECT (BI secting RECTangles) algorithm referred to as BIRECTv. We explore various approaches, by first including a grouping strategy for hyper-rectangles having almost the same sizes by categorizing them into different classes. Therefore constraining them not to exceed a certain pre-defined threshold (a small positive value to define the tolerance level). This approach allows for more efficient computation and can be particularly useful when dealing with a large number of hyper-rectangles with varying sizes. To avoid over-sampling, and preventing redundant or excessive sampling, at some shared vertices in descendant subregions, a particular vertex database is used to limit the number of samples taken within each subregion to two. The experimental investigation shows that these improvements have a positive impact on the performance of the BIRECTv(imp.) algorithm and the proposal is a promising global optimization algorithm compared to the original BIRECTv algorithm and its variants. Additionally, the BIRECTv(imp.) algorithm showed particular efficacy in solving high-dimensional problems.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

Background and Aims: The impact of antibody response after direct-acting antiviral (DAA) therapy in hepatitis C virus (HCV)-infected recipients before and after liver transplantation (LT) is still undetermined. Methods: In this observational cohort study, we aimed to explore the association of changes in anti-HCV antibody titers after pre-LT DAA therapy with allograft injury, including biliary complications (BCs) and acute cellular rejection (ACR). Results: A total of 153 cases were enrolled from January 2015 to February 2021. Serum anti-HCV antibody titers were assessed before and after (day 30) LT. Among all recipients, 31/153 (20.3%) had pre-LT DAA therapy (DAA group) and 122/153 (79.7%) did not undergo pre-LT DAA therapy (DAA-naïve group). Higher incidence of post-LT BCs was observed in the DAA group (P = 0.028). Compared with the DAA-naïve group, the DAA group had a significantly higher mean level of anti-HCV titer upregulation (P = 0.0024); furthermore, among the recipients with BCs (n = 28) and ACR (n = 41), those in the DAA group exhibited significantly higher mean levels of anti-HCV antibody titer upregulation (P < 0.005). Conclusion: In conclusion, we speculated that anti-HCV antibody titer upregulation, which might have been induced by restoration of HCV-specific immune responses with pre-LT DAA therapy, were associated with post-LT allograft injury.

Combining antiviral drugs with different mechanisms of action can help prevent the development of resistance by attacking the infectious agent through multiple pathways. Additionally, by using faster and more economical screening methods, effective synergistic drug candidates can be rapidly identified, facilitating faster paths to clinical testing. In this work, a rapid method was standardized to identify possible synergisms from drug combinations. We analyzed the possible reduction of antiviral effective concentration of drugs already approved by the FDA, such as ivermectin  (IVM), ribavirin (RIBA) and acyclovir (ACV) against Zika virus (ZIKV), Chikungunya virus (CHIKV) and herpes virus type 2 (HHV-2). Essential oils (EOs) were also included in the study since they have been reported for more than a couple of decades to have broad-spectrum antiviral activity. We also continued studying the antiviral properties of one of our patented molecule with broad-spectrum antiviral activity, the ferruginol analogue 18-(phthalimid-2-yl)ferruginol (phthFGL). In general, the combination of IVM, phthFGL and Oregano EO showed the greatest synergism potential against CHIKV, ZIKV and HHV-2, obtaining a reduction in the EC99 value of up to ~8, and ~27, and ~12-fold for CHIKV, in example, respectively. The ternary combination RIBA, phthFGL, Oregano EO was slightly more efficient than the binary combination RIBA/phthFGL but much less efficient than IVM, phthFGL, Oregano EO which indicates that IVM could contribute more to the differentiations of cell targets (for example by inhibition of host heterodimeric importin IMP α/β1 complex) than ribavirin. PhthFGL showed a good pharmacokinetic profile.

Laser direct writing allows for the fabrication of complex structures, which is particularly advantageous in micro-optic applications. However, the increasing demand for optics quality requires the lowest optical power loss, which can occur from unwanted reflections. This research demonstrates the possibility of forming an anti-reflective coating on hybrid-polymer micro-lenses fabricated by employing laser direct writing (LDW), without changing their geometry. Such coating deposited by atomic layer deposition (ALD) decreased the reflection from 3.3 % to 0.1 % at the wavelength of 633 nm for one surface of SZ2080™.

Bioelectrochemical systems (BESs) have great potential in renewable energy production technologies. BES can generate electricity via Microbial Fuel Cell (MFC) or use the electric current for the synthesis of valuable commodities in Microbial Electrolysis Cells (MECs). The number of various reactor configurations and operational protocols increasing rapidly although, the industrial scale operation is still facing difficulties. This article reviews the recent BES related to literature, with special attention to electrosynthesis and the most promising reactor configurations. We also attempted to clarify the numerous definitions proposed for BESs. The main components of BES are highlighted. Although the comparison of the various fermentation systems is we collected useful and generally applicable operational parameters to be used for comparative studies. A brief overview to link the appropriate microbes to the optimal reactor design is given.

The emission of black carbon (BC) particles, which cause atmospheric warming by affecting radiation budget in the atmosphere, is the result of an incomplete combustion process of organic materials. The recent wildfire event during the summer 2019-2020 in South-Eastern Australia was unprecedented in scale. The wildfires lasted for nearly 3 months over large areas of the two most populated states of New South Wales and Victoria. This study on the emission and dispersion of BC emitted from the biomass burnings of the wildfires using the Weather Research Forecast – Chemistry (WRF-Chem) model is aimed to determine the extent of the BC spatial dispersion and ground concentration distribution and the effect of BC on air quality and radiative transfer at the top of the atmosphere, the atmosphere and on the ground. The predicted aerosol concentration and AOD are compared with the observed data from the New South Wales Department of Planning and Environment (DPE) aethalometer and air quality network and from remote sensing data. The BC concentration as predicted from WRF-Chem model is in general less than the observed data as measured from the aethalometer monitoring network, but the spatial pattern corresponds well, and the correlation is relatively high. The total BC emission into the atmosphere during the event and the effect on radiation budget were also estimated. This study shows that the summer 2019-2020 wildfires affect not only the air quality and health impact on the east coast of Australia but also short-term weather in the region via aerosol interactions with radiation and cloud.

We study in this work a dilute granular gas immersed in a thermal bath made of smaller particles with nonnegligible masses as compared with the granular ones. The kinetic theory for this system is developed and described by an Enskog--Fokker--Planck equation for the one-particle velocity distribution function. Granular particles are assumed to have inelastic and hard interactions, losing energy in collisions as accounted by a constant coefficient of normal restitution. The interaction with the thermal bath is based on a nonlinear drag force plus a white-noise stochastic force. To get explicit results of the temperature aging and steady states, Maxwellian and first Sonine approximations are developed. The latter takes into account the coupling of the excess kurtosis with the temperature. Theoretical predictions are compared with direct simulation Monte Carlo and event-driven molecular dynamics simulations. While good results for the granular temperature are obtained from the Maxwellian approximation, a much better agreement, especially as inelasticity and drag nonlinearity increase, is found when using the first Sonine approximation. The latter approximation is, additionally, crucial to account for memory effects like Mpemba and Kovacs-like ones.

The availability of simple SARS-CoV-2 detection methods is crucial to contain the COVID-19 pandemic. This study examined whether a commercial LAMP assay can reliably detect SARS-CoV-2 genomes directly in respiratory samples without having to extract nucleic acids (NA) beforehand. Nasopharyngeal swabs (NPS, n = 220) were tested by real-time reverse transcription (RT)-PCR and with the LAMP assay. For RT-PCR, NA were investigated. For LAMP, NA from 26 NPS in viral transport medium (VTM) were tested. The other 194 NPS were analyzed directly without prior NA extraction [140 samples in VTM; 54 dry swab samples stirred in phosphate buffered saline]. Ten NPS were tested directly by LAMP using a sous-vide cooking unit. The isothermal assay demonstrated excellent specificity (100%) but moderate sensitivity (68.8%), with a positive predictive value of 1 and a negative predictive value of 0.65 for direct testing of NPS in VTM. The use of dry swabs, even without NA extraction, improved the analytical sensitivity; up to 6% of samples showed signs of inhibition. The LAMP could be performed successfully with a sous-vide cooking unit. This technique is very fast, requires little laboratory resources and can replace rapid antigen tests or verify reactive rapid tests on site.

Direct yaw moment control (DYC) is an effective way to alter the behaviour of electric cars with independent drives. Controlling the torque applied to each wheel can improve the handling performance of a vehicle making it safer andfaster on a race track. The state-of-the-art literature covers the comparison of various controllers (PID, LPV, LQR, SMC, etc.) using ISO manoeuvres. However, more advanced comparison on important characteristics of the controllers performance is missed, such as the robustness of the controllers under changes in the vehicle model, steering behaviour, use of the friction circle and, ultimately, lap time on a track. In this study, we have compared the controllers according to some of the aforementioned parameters on a modelled race car. Interestingly, best lap times are not provided by perfect neutral or close-to-neutral behaviour of the vehicle, but rather by allowing certain deviations from the target yaw rate. In addition, a modified PID controller showed that its performance is comparable to other more complex control techniques such as MPC.

Ocean wave energy conversion as one of the renewable clean energy sources is attracting the research interests of many people. This review introduces different types of power take-off technology of wave energy converters. The main focus is the linear direct drive power take-off devices as they have the advantages for ocean wave energy conversion. The designs and optimizations of power take-off systems of ocean wave energy converters have been studied from reviewing the recently published literature. Also, the simple hydrodynamics of wave energy converters have been reviewed for design optimization of the wave energy converters at specific wave sites. The novel mechanical designs of the power take-off systems have been compared and investigated in order to increase the energy harvesting efficiency.

This paper addresses the modeling of the iron ore direct reduction process, a process likely to reduce CO₂ emissions from the steel industry. The shaft furnace is divided into three sections (reduction, transition, and cooling), and the model is two-dimensional (cylindrical geometry for the upper sections and conical geometry for the lower one), to correctly describe the lateral gas feed and cooling gas outlet. This model relies on a detailed description of the main physical–chemical and thermal phenomena, using a multi-scale approach. The moving bed is assumed to be comprised of pellets of grains and crystallites. We also take into account eight heterogeneous and two homogeneous chemical reactions. The local mass, energy, and momentum balances are numerically solved, using the finite volume method. This model was successfully validated by simulating the shaft furnaces of two direct reduction plants of different capacities. The calculated results reveal the detailed interior behavior of the shaft furnace operation. Eight different zones can be distinguished, according to their predominant thermal and reaction characteristics. An important finding is the presence of a central zone of lesser temperature and conversion.

In this paper, we analyze the generalized Ulam-Hyers stability of affine type AQ Functional Equation in various Banach Spaces using Direct and Fixed Methods

To clarify the risk factors for aggravation of esophagogastric varices (EGV) after hepatitis C virus (HCV) eradication with direct-acting antiviral (DAA) therapy, we enrolled 167 consecutive patients with HCV-related compensated cirrhosis who achieved a sustained virological response (SVR) after DAA therapy. During a median of 69 months, EGV was aggravated in 42 (25%) patients despite SVR. The cumulative 1, 3, 5, and 10-year aggravated EGV rates were 7%, 23%, 25%, and 27%, respectively. Multivariate analysis identified platelet count <11.0×10⁴/μL, LSM ≥18.0 kPa, total bile acid ≥33.0 μmol/L, and diameter of left gastric vein (LGV) ≥5.0 mm at HCV eradication as independent risk factors for EGV aggravation post-SVR. In groups that meet all of these risks, the cumulative EGV aggravation rates at 1, 3, and 5 years were 27%, 87%, and 91%, respectively. However, none of the patients who had only one or none of the risk factors experienced EGV aggravation. Platelet count, LSM, total bile acid, and diameter of LGV at HCV eradication were associated with aggravated EGV post-SVR. EGV tends to worsen as two or more of these risk factors increase.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

Development of effective treatments for high-grade glioma (HGG) is hampered by 1) the blood-brain barrier (BBB), 2) an infiltrative growth pattern, 3) rapid development of therapeutic resistance, and, in many cases, 4) dose-limiting toxicity due to systemic exposure. Convec-tion-enhanced delivery (CED) has the potential to significantly limit systemic toxicity and in-crease therapeutic index by directly delivering homogenous drug concentrations to the site of disease. In this review, we present clinical experiences and preclinical developments of CED in the setting of high-grade gliomas.

There is a growing use of High Voltage Direct Current (HVDC) globally due to the many advantages of Direct Current (DC) transmission systems over Alternating Current (AC) transmission, including enabling transmission over long distances, higher transmission capacity and efficiency. Moreover, HVDC systems can be a great enabler in the transition to a low carbon electrical power system which is an important objective in today’s society. The objectives of the paper are to give a comprehensive overview of HVDC technology, its development, and present status, and to discuss its salient features, limitations and applications.

We prove general stability theorems for $n$-dimensional quartic-cubic-quadratic-additive type functional equations of the form \begin{eqnarray*} \sum_{i=1}^\ell c_i f \big( a_{i1}x_1 + a_{i2}x_2 + \cdots + a_{in}x_n \big) = 0 \end{eqnarray*} by applying the direct method. These stability theorems can save us much trouble of proving the stability of relevant solutions repeatedly appearing in the stability problems for various functional equations.

This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with high scan angle (± 50º/60º). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses are validated with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 &amp; 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

In this study, a structural profiling of equid alphaherpesvirus 1 (EHV-1) transcriptome was carried out using next-generation (Illumina) and third-generation (Oxford Nanopore Technologies) sequencing platforms. We annotated the canonical mRNA molecules and their isoforms, including transcript start and end site isoforms, and splice variants. Additionally, a number of putative 5′-truncated mRNAs containing shorter in-frame ORFs were detected. We also demonstrated that EHV-1 produces a high number of non-coding transcripts, including antisense and intergenic RNAs. One of the most remarkable features of the EHV-1 is the generation of abundant fusion transcripts some of which encoding chimeric polypeptides. We observed a higher number of splicing and transcriptional overlaps than in related viruses. Additionally, we found that many upstream genes of tandem gene clusters have their own transcript end sites (TESs) besides the co-terminal TESs, which is rare in other alphaherpesviruses. We show here that the replication origins (OriS and OriL) of the virus are co-localized with promoter sequences and overlap with specific RNA molecules. Furthermore, we discovered a novel non-coding RNA (designated as NOIR) that overlaps the 5′-ends of the longer transcript variants encoded by the two main transactivator genes ORF64 and 65 bracketing the OriL. These all suggest the existence of a central regulatory system which controls the genome-wide transcription and the replication through a mechanism based on the interference between the machineries carrying out the synthesis of DNA and RNA.

This study aims to explore the link between public investment and private investment in South Africa, using time series data spanning 40 years (1980–2020). Private investment is subdivided into credit to private sector (CPS) and foreign direct investment (FDI). Several econometric methodologies were used in the study, including the unit root test, cointegration test, and Error Correction Method (ECM). The Phillips-Perron (PP) test results point out that all the variables are stationary at levels with the exception of public investment (PI) which is stationary at first difference. The co-integration test reveals that the variables have a long-run equilibrium relationship. According to the findings of the ECM, public investment has a negative relationship with private investment (as measured by credit to private sector and foreign direct investment). The conclusion implies that in South Africa, public investment crowds out private investment. Other results revealed that, RGDP crowds in credit to private sector while crowding out foreign direct investment. Finally, the ECM findings show that government consumption expenditure crowds out credit to private sector and foreign direct investment. The residuals are homoskedastic and show no serial correlation, indicating that the model is adequate, according to the test for adequacy.

This paper presents an approach to the vibration analysis of axially functionally graded non-prismatic Timoshenko beams (AFGNPTB) using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, shear moduli, and mass density) of axially functionally graded beams vary along the longitudinal axis. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFGNPTB was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFGNPTB, considering the damping. The results obtained in this study showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

In this paper, an offshore airborne wind energy (AWE) farm consisting of three non-reversing pumping mode AWE systems is modelled and simulated. The AWE systems employ permanent magnet synchronous generators (PMSG). A direct interconnection technique is developed and implemented for AWE systems. This method is a new approach invented for interconnecting offshore wind turbines with the least number of required offshore-based power electronic converters. The direct interconnection technique can be beneficial in improving the economy and reliability of marine airborne wind energy systems. The performance and interactions of the directly interconnected generators inside the energy farm internal power grid are investigated. The results of the study conducted in this paper, show the directly interconnected AWE systems can exhibit a poor load balance and significant reactive power exchange which must be addressed. Power control strategies for controlling the active and reactive power of the AWE farm are designed, implemented, and promising results are discussed in this paper.

The article investigates the impact of the Environmental, Social, and Governance (ESG) criteria on the current tax systems worldwide. The ESG principles, although yet to be codified in hard law in most countries, are gaining increasing prominence in shaping business practices and policies. The article explores how these principles might influence the interpretation and application of existing tax rules, even without explicit legal mandates. It delves into four key areas where ESG considerations could play a significant role: the calculation of business income, transfer pricing regulations, the application of anti-avoidance rules, and the interpretation of the "business purpose" test. It argues that ESG principles, by redefining the purpose of a business beyond mere profit maximisation, could lead to a broader understanding of deductible costs, influence transfer pricing decisions, and impact the application of anti-avoidance measures. It concludes by emphasising the potential of ESG principles to shape the future of taxation, promoting a more sustainable and equitable approach to economic growth.

This study comprehensively evaluates the DNA/RNA Defend Pro (DRDP) sample collection buffer designed to inactivate and stabilize patient samples. The primary objectives encompassed assessing DRDP's efficacy in ensuring sample stability, facilitating extraction-free polymerase chain reaction (PCR), and ensuring compatibility with rapid antigen testing.Ninety-five diagnostic nasopharyngeal swab samples tested for influenza A/B, RSV A/B, and/or SARS-CoV-2 were diluted 1/10 with DRDP and anonymized. Stability testing involved incubating 31 positive samples at 4 °C, 20 °C, and 37 °C for 7 days, with regular extraction-free nucleic acid amplification testing (NAAT).Results demonstrated that DRDP guaranteed viral RNA stability at all temperatures for influenza, SARS-CoV-2 and RSV showing stability up to 7 days at 4 °C. DRDP-diluted samples exhibited robust compatibility with direct PCR, as 72 out of 88 samples positive for cobas Liat also tested positive for direct PCR. Non-concordant results could be explained by the 200-fold lower input in the extraction-free NAAT.Compared to NAAT, rapid antigen testing demonstrated lower sensitivity, as expected, while maintaining perfect specificity. Clear cutoffs between positive and negative rapid antigen testing results were observed in both cobas Liat and direct PCR analyses, validating DRDP's compatibility with these techniques. In conclusion, DRDP is an effective stabilizing medium compatible with direct PCR and rapid antigen testing and shows great potential for optimizing diagnostic processes, particularly in resource-limited or time-sensitive scenarios.

Mathematical modeling is the most important tool for constructing the theory of different kinds of two-phase flows. The review is devoted to the analysis of the advent of the approach of mathematical modeling of two-phase flows, where solid particles act mainly as the dispersed phase. The main problems and features of the study of gas-solid two-phase flows are excluded. The main characteristics of gas flows with solid particles are given and the classification of two-phase flows is developed on their basis. The Lagrangian and Euler approaches to modeling the motion of a dispersed phase (particles) are described. Much attention is paid to the consideration of numerical simulation methods that describe descriptions of turbulent gas flow at different hierarchical levels (RANS, LES, DNS), different levels of description of interphase interactions (one-way coupling (OWC), two-way coupling (TWC) and four-way coupling (FWC)), as well as at different levels of interface resolution (partial-point (PP) and particle-resolved (PR)). Excluded are examples of some studies carried out on the basis of the identified approaches, as well as their exclusion for mathematical modeling of various classes of gas-solid two-phase flows.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

This paper presents an approach to the vibration analysis of axially functionally graded (AFG) non-prismatic Euler-Bernoulli beams using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, and mass density) of AFG beams vary along the longitudinal axis. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFG non-prismatic Euler-Bernoulli beams was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFG non-prismatic Euler-Bernoulli beams, considering the damping. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

Background: Objectives. The objective of this study was to compare the efficacy of direct current stimulation (DCS) applied at the transcranial, suboccipital and spinal level on experimental sensory modalities and pain outcome measures in healthy subjects. The hypothesis of this study was that systematic analysis of the efficacy of DCS on modulating evoked thermal and mechanical pain modalities and mechanisms such as endogenous pain modulation in healthy individuals would reveal sensitive outcome measures help develop this technique for the control of chronic pain. Materials and Methods. Database searches were conducted up to December 2019 for randomized controlled trials that performed sham-controlled DCS of experimental sensory modalities and pain outcomes following transcranial, suboccipital and spinal locations in healthy participants. Standardized mean differences with 95% confidence intervals were calculated for sensory modalities, including random-effect metanalysis. Results: Thirty-one studies were included for analysis (647 participants). A significant decrease in pain intensity for active vs sham transcranial stimulation was identified for pain intensity (n=158; SMD=0.79; 95% CI=0.56 to 1.02), a significant increase in heat pain threshold (n=222; SMD=1.16; 95% CI=0.95 to 1.37), and a significant increase in cold pain threshold (n = 155; SMD = 0.77, 95% CI 0.53 to 1.01). No significant modulation of pressure pain threshold was identified with DCS and only a limited number of studies focused on experimental pain modulation following neuromodulation at the suboccipital or spinal level. Conclusions: These results show significant transcranial DCS neuromodulation of pain intensity and on thermal pain modalities. Future studies should focus on endogenous pain and sensory modality modulation with sham-controlled DCS applied at transcranial, suboccipital and spinal locations.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

Visualization of volumetric data holds great importance, particularly in medical and biomedical applications. Various imaging techniques, such as FMRI and 3D microscopy, are employed to generate volumetric data, used in medical practice, research, and teaching. Commonly utilized tools like 3D Slicer, Fiji, and MATLAB ® aid in rendering and analyzing 3D images. However, these tools may lack comprehensive rendering functionality and face challenges in handling computational demands as data sizes grow. To address these limitations, this work introduces a GPU-supported renderer with a MATLAB ® interface. This solution gives the user flexible control over rendering parameters and optimizes data transfer through a memory management system. By leveraging the computational power of NVIDIA GPUs, the renderer enables complex and high-quality renderings, enhancing speed and efficiency. It therefore facilitates the analysis and visualization of volumetric data within an integrated environment, namely MATLAB ®, streamlining their workflows. This advancement provides valuable opportunities for researchers and medical professionals to explore and comprehend volumetric data effectively.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

The article presents an induction generator connected to the power grid using the AC / DC / AC converter and LCL coupling filter. In the converter, both from the generator side and from the power grid side, three-level inverters were used. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field Oriented Control (DFOC) method. At the same time, voltage control has been used for this solution. The MPPT algorithm has been extended to include the variable pitch range of the wind turbine blades. The active voltage balancing circuit has been used in the inverter DC voltage circuit. In the control system of the grid converter with an LCL filter, the number of measurements was limited to the measurement of power grid currents and voltages. Synchronization of control from the power grid side is ensured by the use of a PLL loop with the system of preliminary suppression of undesired harmonics (CDSC).

Chikungunya virus (CHIKV) is a mosquito-transmitted alphavirus that has re-emerged in recent decades, causing large-scale epidemics in many parts of the world. CHIKV infection leads to a febrile disease known as chikungunya fever (CHIKF), which is characterised by severe joint pain and myalgia. As many patients develop a painful chronic stage and neither antiviral drugs nor vaccines are available, the development of a potent CHIKV inhibiting drug is crucial for CHIKF treatment. A comprehensive summary of current antiviral research and development of small-molecule inhibitor against CHIKV is presented in this review. We highlight different approaches used for the identification of such compounds and further discuss the identification and application of promising viral and host targets.

The present paper investigates the effect of poverty on foreign direct investment (FDI) inflows in developing countries. It complements the important extant literature on the effect of FDI inflows on poverty by examining the issue the other way around. The analysis is conducted using a sample of 117 countries over the period 1980-2017, and the two-step system Generalized Methods of Moments (GMM) technique. It has relied on two indicators of poverty, namely poverty headcount ratio and poverty gap. Findings indicate that over the full sample, poverty influences negatively FDI inflows, including through its adverse effect on human capital (that is, both education and health). Unsurprisingly, low-income countries (considered as poorest countries in the full sample) experience a higher negative effect of poverty on FDI inflows than other countries. On another note, participation in international trade matters for the effect of poverty on FDI inflows. In fact, an increase in poverty levels results in lower FDI inflows in countries that experience low workers' productivity, a less developed financial sector, and a low level of infrastructure development. Furthermore, the effect of poverty on FDI inflows does not depend on the prevailing economic growth rate. Finally, the analysis has revealed the existence of a non-linear effect of poverty on FDI inflows for the poverty headcount indicator, but not for the poverty gap indicator. The non-linear effect of poverty headcount on FDI inflows is such that a rise in poverty headcount ratio results in lower FDI inflows, but an additional increase in poverty more than further discourages FDI inflows. The conclusion discusses the implications of these findings.

Direct Behavior Rating (DBR) as a behavioral progress monitoring tool can be designed as longitudinal assessment with only short intervals between measurement points. The reliability of these instruments has been evaluated mostly in observational studies with small samples based on generalizability theory. However, for standardized use in the pedagogical field, a larger and broader sample is required in order to assess measurement invariance between different participant groups and over time. Therefore, we constructed a DBR with multiple items to measure the occurrence of specific externalizing and internalizing student classroom behaviors on a Likert scale (1 = never to 7 = always). In a pilot study, two trained raters observed 16 primary school students and rated the student behavior over all items with a satisfactory reliability. In the main study, 108 regular primary school students, 97 regular secondary school students and 14 students in a clinical setting were rated daily over one week (five measurement points). IRT analyses confirmed the instrument’s technical adequacy, and latent growth models demonstrated the instrument’s stability over time. Further development of the instrument and study designs to implement DBRs are discussed.

The lightcone gauge is a set of what are called the observational coordinates adapted to our past lightcone. We develop this gauge by producing a perturbed spacetime metric that describes the geometry of our past lightcone where observations are usually obtained. We connect the produced observational metric to the perturbed Friedmann-Lema\^itre-Robertson-Walker metric in the standard general gauge or what is the so-called 1+3 gauge. We derive the relations between these perturbations of spacetime in the observational coordinates and those perturbations in the standard metric approach, as well as the dynamical equations for the perturbations in observational coordinates. We also calculate the observables in the lightcone gauge and re-derive them in terms of Bardeen potentials to first order. A verification is made of the observables in the perturbed lightcone gauge with those in the standard gauge. The advantage of the method developed is that the observable relations are simpler than in the standard formalism, and they are expressed in terms of the metric components which in principle are measurable. We use the perturbed lightcone gauge in galaxy surveys and the calculations of galaxy number density contrast. The significance of the new gauge is that by considering the null-like light propagations the calculations are much simpler due to the non-consideration of the angular deviations.

Weed competitive ability (WCA) is a desirable key trait for the improvement of grain yield under direct-seeded rice (DSR) and the aerobic rice ecosystem. The present study targeted screening of 167 introgression lines (ILs) of a Green Super Rice (GSR) IR2-6 population derived from a cross between Weed Tolerant Rice 1 (WTR1) as the recipient parent and Y134 as the donor parent developed at IRRI for weed competitiveness in screen house conditions (SHC). The ILs were phenotyped for WCA traits such as early seed germination (ESG) and early seedling vigor (ESV) in Petri dishes and pot experiment conditions. The results of phenotypic variance revealed ESG-related traits, especially first germination count (1st GC) that positively correlated with second germination count (2nd GC), germination percentage (GP), total dry weight (TDW), total fresh weight (TFW), and vigor index (VI-1), whereas, in ESV, all the traits were positively correlated with each other except for three traits: root dry weight (RDW), 1st GC, and GP-2. The ESG and ESV traits are vital for weed competitiveness. A 6K SNP array was used to study the genetic association for the WCA traits. Forty-four QTLs for WCA traits were mapped on all chromosomes (except on chromosomes 4 and 8) through single marker analysis (SMA). Out of 44 QTLs, 29 were associated with ESG traits and 15 with ESV traits, with LOD scores of 2.93 to 8.03 and 2.93 to 5.04 and explained phenotypic variance ranging from 7.85% to 19.9% and from 7.85% to 13.2%, respectively. However, 31 QTLs were contributed by a negative additive allele from Y134, whereas a positive additive allele was contributed by WTR1 in 13 QTLs. Among them, two QTL hotspot regions were mapped on chromosome 11 (24.7-27.9 Mb) and chromosome 12 (14.8-17.4 Mb). The majority of the QTLs related to WCA traits were grouped into two QTL hotspots: QTL hotspot-I (qAFW11.1, qFC11.1, qFC11.2, qSC11.1, qGP-111.1, qGP-111.2, qTFGS11.1, qVI-111.1, and qVI-111.2) and QTL hotspot-II (qFC12.1, qFC12.2, qSC12.1, qFC12.2, qGP-112.1, qGP-112.2, qTFGS12.1, qTFGS12.2, qVI-112.1, qIV12.2, qFC12.1, and qGC12.2), and a few of them were co-localized on chromosomes 11 and 12. Further, we fine-tuned in the genomic regions of QTL hotspots and identified a total of 13 putative candidate genes on chromosomes 11 and 12 collectively. The present study is the first report on the genetic basis of WCA-related traits and the co-localized QTLs, which could be highly valuable in future breeding programs aiming to improve WCA in rice.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

A specialized microenvironment in the bone marrow, composed of stromal cells including mesenchymal stem cells (MSCs), support hematopoietic stem cells (HSCs) self-renewal and differentiation but also regulates leukemia development and progression. The reciprocal direct interaction between MSCs and CD34+ HSCs under physiological and pathological conditions has not been well characterized yet. Here, we established a direct co-culture model between MSCs and CD34+ HSCs or MSCs and acute myeloid leukemia cells (THP-1, Molm-13, and primary cells from patients) to study cell-cell communication. Following MSCs-CD34+ HSCs co-culture, the expression of adhesion markers N-cadherin and connexin 43 increased in both cell types, forming gap junction channels. Moreover, the clonogenic potential of CD34+ HSCs was increased. However, direct contact of acute myeloid leukemia cells with MSCs reduced the expression levels of connexin 43 and N-cadherin in MSCs. The impairment in gap junction formation could be ascertained to a defect in the acute myeloid leukemia derived MSCs. Interestingly, CD34+ HSCs and acute myeloid leukemia cell lines restrained MSCs from engaging into osteoblastic differentiation upon prolonged direct cell-cell contact. In conclusion, under physiological conditions, connexin 43 and N-cadherin interaction preserves stemness of both CD34+ HSCs and MSCs, a process that is compromised in acute myeloid leukemia, pointing out to the possible role of gap junctions in modulating stemness.

Pain is a multifaceted multisystem disorder that adversely affects neuro-psychological processes. This study compares the effectiveness of central-stimulation (tDCS) and peripheral-stimulation (TENS) in pain-inhibition during a cognitive-task in healthy volunteers and to observe potential neuro-cognitive improvements. Healthy eighty volunteers went through a complete experimental protocol comprising pain-induction (CPT), administration of tDCS/TENS, EEG-data acquisition, and cognitive assessments. The protocol for this study is categorized into 04-groups: G1(Control), G2(TENS), G3(Anodal-tDCS), and G4(Cathodal-tDCS). Paired t-tests (p

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Transcranial direct current stimulation (tDCS) over the left Inferior Frontal Gyrus (IFG) was found to improve apraxia of speech (AOS) in post-stroke aphasia, speech fluency in adults who stutter, naming and spelling in primary progressive (PPA). This paper aims to determine whether tDCS over the left IFG coupled with AOS therapy improves speech fluency in patients with PPA more than sham. Eight patients with non-fluent PPA with AOS symptoms received either active or sham tDCS, along with speech therapy for 15 weekday sessions. Speech therapy consisted of repetition of increasing syllable-length words. Evaluations took place before, immediately after, and two months post-intervention. Words were segmented into vowels and consonants and the duration of each vowel and consonant was measured. Segmental duration was significantly shorter after tDCS than sham for both consonants and vowels. tDCS gains generalized to untrained words. The effects of tDCS sustained over two months post-treatment in trained words. Taken together, these results demonstrate that the tDCS over the left IFG facilitates speech production by reducing segmental duration. The results provide preliminary evidence that tDCS can maximize efficacy of speech therapy in non-fluent PPA with AOS.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Background/Objectives: Post traumatic growth (PTG) has the potential to draw positive consequences from trauma. Hence, the interest of finding ways to promote PTG. Research has identified an attentional bias towards positive resilience-related words (e.g., “persistence”, “purpose”) in university students who report high PTG after experiencing adversities. Although people can respond to these experiences by showing low PTG, this bias seems to help with their struggle by making purposeful contents more accessible. Therefore, boosting attentional bias towards positive resilience-related words could help people with low PTG. Methods: In this study, the participants were thirty-six university students who had experienced bullying before entering university. Using a Stroop emotional task, they identified the color of resilience and neutral words, either positive or negative, before and after being submitted to transcranial direct current stimulation. Stimulation was targeted at the right temporal area involved in intentionality processing. Results: In the anodal condition, the results support a stimulation effect on the resilience attentional bias that could benefit participants with low PTG. A significant moderation of approach motivation for this effect was also found. Specifically, only when participants had medium or high approach motivation, did stimulation boost the attentional bias in students with low PTG. Conclusions: These results support that tDCS stimulation in this brain area is effective in enhancing resilience attentional bias in low PTG students. However, for this effect to occur it is necessary to have approach motivation, which is motivation related to goals.

Purpose: This integrated review aims to identify and analyze the multifactorial contributors to the longevity of direct restorations, focusing on tooth-, patient-, and dentist-related factors. Materials and Methods: A literature search was performed using an electronic database, PubMed/Medline, Web of Science, and Scopus, between 1980 and 2024. Titles and abstracts of papers that evaluated aspects categorized into tooth-related, patient-related, and dentist-related factors influencing restoration failure were selected and screened. Full-text assessments were conducted, and the extracted data were compiled, summarized, and synthesized. The reference lists of the collected papers were also screened, and relevant citations were included in this review. Data were gathered from clinical and laboratorial studies, systematic reviews, and meta-analyses to provide a comprehensive understanding of restoration longevity. Results: Among the tooth-related factors, multiple-surface restorations, deep margins, tooth location, and tooth vitality significantly impact restoration survival. Patient-related factors such as medical conditions, risk predictors of caries, age, sex, parafunctional habits, smoking, periodontal health, number of restorations, and socioeconomic status all play crucial roles. Regarding dentist-related factors, the decision-making process, age, experience, and dentist manual dexterity are vital aspects. Furthermore, the technique used, including isolation methods for moisture control, as well as the type of dental practice (large group vs. small practice), notably influenced the restoration survival. Conclusions: The longevity of dental restorations is influenced by a complex interplay of tooth-related, patient-related, and dentist-related factors. Strategies to improve restoration outcomes should consider all these multifactorial contributors. Continuing professional education, diligent patient guidance on the factors that influence restoration survival, careful material selection and restorative technique, and tailored individual treatment are crucial factors to reduce failure rates and improve the lifespan of restorations.

Cognitive impairment is a condition which affects aging patient populations and is becoming more prevalent as the geriatric population expands. It is categorized by the extent of cognitive decline, memory loss, functional abilities, and the capability to perform daily tasks. Based on the degree of impairment, it is classified as mild cognitive impairment or dementia. Considering the debilitating nature of cognitive decline and its impact on quality of life, prevention is key. In addition, given the gradual progression of the underlying causes of cognitive decline, early diagnosis and appropriate management has the potential to offer clinical advantages and better patient outcomes. Management options discussed vary from pharmaceutical regimens to neurosurgical interventions, with differing outcomes based on etiology of cognitive impairment.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

Background and Aims: Sustained virologic response (SVR) lead to the decrease of portal hypertension, the regression of fibrosis, the improvement of the hepatic synthesis of procoagulant and anticoagulant factors. We aimed to assess the influence of SVR on coagulation parameters in HCV cirrhotic patients treated with DAAs. Methods: We performed a prospective study in the Institute of Gastroenterology and Hepatology Iasi, Romania, between January 2022 and February 2024. We included patients diagnosed with compensated and decompensated HCV-related liver cirrhosis, treated with direct antivirals (PrOD ± RBV or SOF/LED ± RBV) for 12/24 weeks. Blood samples for biochemical, immunological and coagulation tests were collected at baseline, EOT and SVR12/24. Results: We analyzed a group of 52 patients with HCV-related liver cirrhosis, predominantly female (68.0%), the degree of severity of cirrhosis placed the patients mainly in Child-Pugh classes B (40%) and C (36%). All patients achieved SVR. The MELD score decrease at EOT (13.48 ± 4.273; p =0.001), and SVR (9.88 ± 2.774; p = 0.000), compared to baseline (14.92 ± 4.707). Fibroscan values decreased at SVR (17.596 ± 3.7276; p = 0.000) compared to baseline (26.068 ± 7.0954). For all common coagulation parameters (platelets, INR, PT, fibrinogen, aPTT) there was a trend towards improvement during treatment, changes that were statistically significant for the majority of patients. Factor II low at baseline (75.40 ± 7.506), increases at EOT (87.40 ± 9.587), and later at SVR (99.12 ± 11.695; p = 0.000). FVIII values increased at baseline (175.52 ± 16.414) decrease at EOT (151.48 ± 13.703) and SVR (143.40 ± 13.937). FvW values decreased during treatment (146.84 ± 9.428 – baseline, 141.32 ± 9.690; p =0.000 – EOT, 126.68 ± 17.960 – SVR). In regards to the anticoagulant factors (PC, PS, ATIII), a significant improvement was brought on by SVR. Advanced stages of liver disease showed the most diminished FII activity, while at baseline and in Child-Pugh C patients we recorded the highest values of FVIII and FvW. Conclusions: Our study proved that the “reset” of the coagulopathy might be due to the improving of the liver function due to viral eradication secondary to AAD therapy.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Background: In Transcranial Direct Current Stimulation (tDCS) the injected current gets distributed across the brain areas. The motive is to stimulate the target region-of-interest (ROI), while minimizing the current in non-target ROIs. For this purpose, determining the appropriate current-dose for an individual is difficult. Aim: To introduce Dose-Target-Determination-Index (DTDI) to quantify the focality of tDCS and examine the dose-focality relationship in three different populations. Method: Here, we extended our previous toolbox i-SATA to the MNI reference space. After a tDCS montage is simulated for a current-dose, the i-SATA(MNI) computes the average (over voxels) current density for every region in the brain. DTDI is the ratio of average current density at target ROI to the ROI with maximum value (peak region). Ideally target ROI should be the peak region, so DTDI shall range from 0 to 1. Higher the value, the better the dose. We estimated the variation of DTDI within and across individuals using T1-weighted brain images of 45 males and females distributed equally across three age groups- (a) Young adults (20 ≥ x ˂ 40 years), (b) Mid adults (40 ≥ x ˂ 60 years), and (c) Older adults (60 ≥ x ˂ 80 years). DTDI’s were evaluated for the frontal montage with electrodes at F3 and right supra-orbital for three current doses 1mA, 2mA, and 3mA with the target ROI at left middle frontal gyrus. Result: As the dose is incremented, DTDI may show (a) increase, (b) decrease, and (c) no change across the individuals. The focality decreases with age and the decline is stronger in males. Higher current dose at older age can enhance the focality of stimulation. Conclusion: DTDI provides information on which tDCS current dose will optimize the focality of stimulation. DTDI recommended dose should be prioritised based on the age (> 40 years) and sex (especially males) of an individual. The toolbox i-SATA(MNI) is freely available.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Electrical energy demand increase does evolve rapidly due to several socioeconomic factors such as industrialization, population growth, urbanization and of course the evolution of modern technologies in this 4th industrial revolution era. Such rapid increase in energy demand introduces a huge challenge in power system. Such has paved way for network operators to seek for alternative energy resources other than the conventional fossil fuel system. Hence, the penetration of renewable energy into the electricity supply mix has evolved rapidly in the past three decades. However, the grid system has to be well planned ahead to accommodate such increase in energy demand in the long run. Transmission Network Expansion Planning (TNEP) is a well ordered and profitable expansion of power facilities that meets the expected electric energy demand with an allowable degree of reliability. This paper proposes a TNEP model that minimises the network reinforcements, operational costs and costs of renewable energy penetrations, while satisfying the increase in demand. The problem is formulated as a mixed integer linear programming (MILP) problem. The developed model has been tested in several IEEE test systems in multi-period scenarios. The paper also carried out a detailed derivation of the new non-negative variables in terms of the power flow magnitudes, the bus voltage phase angles and the lines’ phase angles for proper mixed integer variables’ decomposition techniques. Moreover, this paper tends to provide additional recommendation in terms of which particular year (within 20 years of planning period) can the network operators install new line(s), new corridor(s) and/or additional generation capacity to the respective existing power networks. Such is achieved by running incremental periods simulations from base year through the planning horizon. The results show the efficacy of the developed model in solving the TNEP problem with a reduced and acceptable computation time even for large power grid system.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.