Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

The research results presented in the article were carried out during the realization of the project, the aim of which is to develop a method of drying cellulose insulation in power transformers with the use of synthetic ester. This method uses a very high water absorption of the ester. During the drying of transformers, the ester is systematically contaminated with mineral oil, which gradually loses its ability to absorb water. Information on the oil concentration in the mixture is needed in two cases: at the stage of making a decision on the treatment of the mixture and during its treatment. The article presents the results of investigations of two methods: 1) based on the measurement of the mixture density, and 2) based on the measurement of the capacitance of the capacitor immersed in the mixture. The conducted research shows that the method of measuring the density of the mixture gives an uncertainty of 2.6 p. %, while the method of measuring the capacitance of a capacitor gives an uncertainty of 2.2 p. %. A significant advantage of the method of measuring the capacitance is the possibility of using it online to control the ester treatment process.

Wastewater treatment from oils and oil products, organic mixtures are a very relevant topic that can be successfully used to solve problems of serious environmental pollution, such as oil spills, industrial oily wastewater discharges and water treatment in the water treatment process. In this work, we have developed new superhydrophobic magnetic polyurethane (PU) sponges functionalized with reduced graphene oxide (RGO), MgFe2O4 nanoparticles, and silicone oil (SO) as a selective and reusable sorbent for purification and separation of wastewater from oils and organic solvents. The surface morphology and wettability of the sponge surface were characterized by scanning electron microscopy (SEM) and a contact angle analysis system, respectively. The results showed that the obtained PU sponge PU/RGO/MgFe2O4/SO had excellent mechanical and water-repellent properties, reusable properties (more than 20 cycles), as well as fast (immersion time 20 sec) and excellent adsorption capacity (16.61- 44.86 g / g), and good magnetic properties made it easy to separate the sponge from the water with a magnet. And the presence of RGO in the composition of the nanomaterial improves the separating and cleaning properties of materials, and also leads to an increase in the absorption capacity of oil and various organic solvents. The synthesized PU sponge has great potential for practical applications due to its facile fabrication and excellent oil-water separation property.

The presented results of simulations take into account the optical parameters of the selected sea region (from literature data on the southern Baltic Sea) and two optically extreme types of crude oil (from historical data) which exist in the form of a highly diluted oil-in-water emulsion (10 ppm). The spectral index was analyzed based on the results of modelling the radiance reflectance distribution for almost an entire hemisphere of the sky (zenith angle from 0 to 80o). The spectral index was selected and is universal for all optically different types of oil (wavelengths 650 and 412 nm). The possibility of detecting pollution in the conditions of the wavy sea surface (as a result of wind of up to 10 m/s) was studied. It has been also shown that if the viewing direction is close to a direction perpendicular to the sea surface, observations aimed at determining the spectral index are less effective than observation under the zenith angle of incidence of sunlight for all azimuths excluding the direction of sunlight specular reflection.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

The petroleum industry produces thousands of barrels of oilfield waters from the initial stage driven by primary production mechanisms to the tertiary stage. These produced waters contain measurable amounts of oil in water emulsions, the exact amounts being determined by the chemistry of the crude oil. To meet strict environmental regulations governing the disposal of such produced waters, demulsification to regulatory permissible levels is required. Within the electric double layer theory, coupled with the analytical solutions to the Poisson Boltzmann Equation, continuum electrostatics approaches can be used to describe the static and electrokinetic properties of such emulsion systems. Therefore, theoretical understanding of the stability of oil in water emulsions within such fundamental concepts provides reliable approaches to demulsification. In this paper, we have used theoretical approaches, based on zeta potential and surface charge density models to determine the stability of oil in water emulsions for different crude oil samples. Accordingly, we have used literature based data on the chemistry of the crude oils, and have ranked the order of emulsion stability based on criterial established by zeta potential plots for the oil. Our theoretical calculations show that where the isoelectric points of crude oil samples are closer to each other, the degree of ionization plots versus pH indicate close tends for salinities at varying pH of oilfield waters. Based on the chemistry of crude oil samples, the most efficient and cost-effective means of demulsification is by reducing produced water pH to values closer to the average point of zero charge pH values

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

Plasma-activated water (PAW) is an emerging and promising green technology in the agriculture sector during recent years. The aim of this study was to examine the influence of the spraying of PAW and amino acid fertilizer concentrations on the physiological, biochemical and phytochemical characteristics of German chamomile varieties under field conditions. Method: The experiment was performed during 2020–2021 as a factorial using a randomized complete block design with three replications, in an arid and warm region. The factors contained five fertilizer levels (0 (control), 1, 2, 3 ml·L−1 amino acid and PAW) and three German chamomile cultivars Bona, Bodegold, Lianka). Physiological, biochemical and phytochemical traits such as plant height, fresh and dried flower weight, chlorophyll a, b, carotenoids, CHN elements, C:N ratio, total protein, amino acid profile, essential oil yield, apigenin content and major secondary metabolites were examined. Results: The ANOVA indicated that the impact of the cultivar and fertilizer was significant on all physiological, biochemical and phytochemical studied parameters. The amino acid fertilizer and PAW enhanced physiological features, hydrogen, C:N ratio, essential oil yield, apigenin content and main phytochemical compositions like chamazulene and α-bisabolol, but it had no incremental effect on the carbon, nitrogen, and total protein percentage. Conclusion: Findings revealed that the application of foliar amino acid fertilizer and PAW treatments improves physiological, biochemical and phytochemical parameters in German chamomile cultivars under field conditions.

Rotary drilling for oil and natural gas uses drilling fluid for lubrication of the bit, to seal off unstable shale layers, and floating out rock cuttings. Drilling fluid is a water-clay chemical mixture. Produced water is a water-sand chemical mixture. Land farming is a common disposal technique of drilling fluid and produced water. In the land farming process, amendments of fluid are repeatedly applied to the soil surface. Plant growth and soil chemical properties may be altered by additions of drilling fluid, because of alkalinity, salinity, trace elements, and petroleum residue contained in waste. The objective of this study was to determine the change in soil pH, electrical conductivity (EC), total nitrogen and carbon, and extractable nutrient levels following the land application of drilling fluid and produced water. The study was a comparison of three plots with similar soil properties and conditions. The three study plots had various levels of drilling fluid and produced water applications. The data show a major difference from field-to-field for EC, Na, and Cl levels. The EC and salt levels increased with additional applications of drilling fluid and produced water. The percent total nitrogen values and plant available P levels were very low in all fields. High EC and salt values, coupled with low N and P levels, would be detrimental to plant growth and development. To successfully vegetate this land-farm site, application of N and P fertilizer would be required. This study will help to give a better understanding of practical ways to land-farm drilling fluid and produced water in a fashion that both minimizes environmental issues and is economically feasible. Salinity changes to soil were expected to be high; there are excessive amounts of sodium and chloride in spent drilling fluid and produced water.

Various environmental challenges, related to oil palm commodity has became a major environmental challenge to oil palm production. The aim and objective of this study is to analyze the actual water footprint of oil palm based on root water uptake under varying crop age and soil type. The research was conducted in Pundu Village, Central Kalimantan. The methodology adopted in carrying out this study consists of various stages which includes observing soil moisture, rainfall, and water table, ETo, root water uptake and oil palm water footprint. The highest rate of water consumption was the 13 years oil palm on spodosol soil type with an average daily rate of 3.73 mm/day. The lowest evapotranspiration was represented by the 7th year oil palm on spodosol with an average rate of 3.07 mm/day. The total water footprint value obtained was between 0.56 – 1.14 m3/kg for a variety of plants with various age and soil types. It can be deduced that the water footprint value of oil palm vary for different crop age and soil types on temporal scale. The study also presented that the source of green water from the first root zone of oil palm deliver the highest contribution for oil palm root water uptake.

Oil-water separation using special wettability materials has received much attention due to its low energy consumption and high separation efficiency. Herein, a fluorine-free superhydrophobic cotton fabric(PDMS/STA -coated cotton fabric) was successfully prepared by a simple impregnation method using hydroxyl-capped polydimethylsiloxane (PDMS-OH), tetraethoxysilane (TEOS) and stearic acid (STA) as precursors. The Investigation found that the cross-linking reactions between the hydroxyl groups form PDMS-OH, hydrolyzed TEOS made a strong interact of PDMS-OH and cotton fabric. Besides, a suitable roughness surface of coated cotton fabric was established by introducing STA due to its long chain-structure. The contact angle of this composite can reach 158.7°under optical condition due to its low surface energy and desired roughness. The oil/water separation efficiency of PDMS/STA-coated cotton fabric is higher than 90% even after 10 cycles of oil-water separation, the oil flux can reach 11862.42 L m-2 h-1. In addition, PDMS/STA-coated cotton fabric exhibits excellent chemical stability and durability under extreme conditions such as strong acid (HCl, pH=1~2) and alkali (NaOH, pH=13~14), the hydrophobicity of PDMS/STA-coated cotton fabric was decreased to 147° even after 350 cycles of abrasion testing.

Pressure drop and flow pattern of oil-water flows were investigated in a 19 mm ID clear polyvinyl chloride pipe consisting of U-bend with radius of curvature of 100 mm. The range for oil and water superficial velocities tested were and respectively. Measurements were carried out under different flow conditions in a test section that consisted of four different parts: upstream of the bend, at the bend and at two redeveloping flow locations after the bend. The result indicated that the bend had limited influence on downstream flow patterns. However, the shear forces imposed by the bend caused some shift flow pattern transition and bubble characteristics in the redeveloping flow section after the bend relative to develop flow before the bend. Generally, pressure gradient at all the test sections increased with both oil fraction and water superficial velocity and there was a sharp change of pressure gradient profile during phase inversion. The transition point where phase inversion occurred was always within the range of . Pressure losses differed at the various test sections and the difference was strongly linked to the superficial velocity of the phases and the flow pattern. At high mixture velocity, pressure losses at the redeveloping section after the bend were higher than that at the bend and that for fully developed flows. At low mixture velocity, pressure losses at the bend are higher than in the straight sections. Pressure drop generally decreased with level of flow development downstream of the bend.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

A quasi-two-dimensional (quasi-2D) modelling approach is introduced to mimic transverse mixing of an inflow into a river from one of its banks, either an industrial outfall or a tributary. The concentrations of determinands in the inflow vary greatly from those in the river, leading to very long mixing lengths in the river downstream of the inflow location. Ideally, a two-dimensional (2D) model would be used on a small scale to capture the mixing of the two flow streams. However, for large-scale applications of several hundreds of kilometres of river length, such an approach demands too many computational resources and too much computational time, especially if the application will at some point require ensemble input from climate-change scenario data. However, a one-dimensional (1D) model with variables varying in the longitudinal flow direction but averaged across the cross-sections is too simple of an approach to capture the lateral mixing between different flow streams within the river. Hence, a quasi-2D method is proposed in which a simplified 1D solver is still applied but the discretisation of the model setup can be carried out in such a way as to enable a 2D representation of the model domain. The quasi-2D model setup also allows secondary channels and side lakes in floodplains to be incorporated into the discretisation. To show proof-of-concept, the approach has been tested on a stretch of the lower Athabasca River in Canada flowing through the oil sands region between Fort McMurray and Fort MacKay. A dye tracer and suspended sediments are the constituents modelled in this test case.

A new method is proposed to increase rejection in microfiltration by applying membrane oscillation using a new type of microfiltration membranes with slotted pores. The oscillations applied to the membrane surface result in reducing membrane fouling and increasing separation efficiency. An exact mathematical solution of the flow in the surrounding solution outside the oscillating membrane is developed. The oscillation results in appearance of the lift velocity, which moves oil particles away from the membrane. The latter results in both reducing membrane fouling and increasing oil droplets rejection. This developed model was supported by the experimental results for oil water separation in produced water treatment. It was proven that oil droplet concentration reduced notably in the permeate due to the membrane oscillation and that applied shear rate caused by the membrane oscillation is also reduce pore blockage. New generation of microfiltration membranes with slotted pores was used in the experiments.

The energy matrix worldwide has been going through difficulties in its discussions - such as irregular exploration, inefficient public policies, and arbitrariness concerning diplomatic and political definitions of those involved in this market. This work's general objective consists in analyzing associations and statistical inferences of the largest world oil producers, assimilating the contributions and singularities of this market from 1993 to 2020. Based on the Organization of the Petroleum Exporting Countries (OPEC), it was possible to identify the possible inferences and contributions of the ten largest oil producers in the world in more than two decades using statistical analysis through correlation, regression, and statistical analysis of variables. According to the research and the literature on the area, the oil market proposes support to its discussions, mainly in its productive approaches. It is possible to identify this market as a solid link to geopolitical actions, distributing the possibilities through economic bias and socio-cultural and historical factors on a global level.

The article is devoted to the topical problem of estimating water content in water-oil mixtures and porous media they saturate, according to low-field NMR relaxometry and dielectric spectroscopy. The aim of the research is to theoretically substantiate and experimentally validate the capability of joint interpretation of data from these methods to acquire information on the filtration-volumetric properties of drill cuttings, relaxation characteristics of oil-containing fluids, water/oil ratio in water-oil mixtures and saturated with them drill cuttings in order to control the composition of liquids produced from boreholes. The studies were carried out on samples of cuttings and oils taken from fields in the northern and Arctic regions of the West Siberian oil-and-gas province. Based on the experimental data obtained, we evaluated the water content in the water-oil mixtures, determined the main NMR parameters of the mixtures in terms of properties of the constituent oils, and specified the parameters and shapes of NMR and complex dielectric permittivity spectra. The NMR method was found to be effective in examining high-viscosity and medium-viscosity oils, while the dielectric spectroscopy method – in the study of light oils; their integration allows obtaining reliable data for all the samples under study. We also showed how the shapes of NMR and complex dielectric permittivity spectra depend on the rheological properties of oil belonging to the mixture.

In this article, we report the generation of alternating current by application of constant and ramping DC voltages across oil-water interfaces. The work reported here can be broadly divided into two parts depending on the shapes of oil-water interfaces i.e. flattened and curved. In the first part, an alternating current of ~100 nA (amplitude)was generated by applying a constant DC voltage of -3V& above across a free standing and flattened oil-water interface.In another part, an alternating current of ~150 nA (amplitude) was generated by applying a ramping up DC voltage starting from -5V to 5V, then again ramping back down to -5V for the free standing and curved interface. The suggested qualitative mechanism that engenders such a phenomenon includes the oil-water interface acting like a membrane. This membrane oscillates due to the electrophoretic movement of ions present in aqueous phase by application of a DC voltage across the interface.This electrophoretic movement of ions across oil-water interfaces causes the Faraday instabilities leading to oscillations of the said interface.This method could also be used to study the stress levels in the interfacial films between two immiscible liquids. It explores more-than-Moore’s paradigm by finding a substitute to a conventional alternator/inverter that generates alternating current upon applying DC voltage input. This work would be of substantial interest to researchers exploring alternatives to conventional AC generators that can be used in liquid environments and in the design of novel integrated circuits that could be used for unconventional computing applications.

Due to its economic benefits and the ability to reduce carbon emissions on a large scale, the CCUS-EOR project has been widely promoted and implemented globally. By using carbon dioxide flooding, oil water transition zone reservoirs that were once considered worthless may have new potential for development because of its rich geological reserves and high quality carbon sequestration conditions. Unlike water flooded layer, the oil in the TZ is unsaturated rather than residual oil after water flooding, which would lead to special oil-water seepage law of initial oil saturation. It is necessary to clarify special oil-water seepage law of oil-water transition zone to evaluate its production & storage potential. In this paper, we present a series of experiments to characterize the relationship between residual oil saturation and initial oil saturation. Cores in four different permeability and oil in four different viscosity are used to simulate different reservoir conditions, and that CO2 immiscible flooding experiments for each cores permeability and oil viscosity are performed with four different initial oil saturation. A total of 36 sets of CO2 flooding experiment data are used to draw the initial oil saturation & residual oil saturation chart. The results show that the residual oil saturation depends on the initial oil saturation rather than constant under certain conditions of core and oil. Under the condition of low permeability and high oil viscosity, the influence of initial oil saturation on residual oil saturation is relatively strong. The initial oil saturation & residual oil saturation chart can accurately calculate the residual oil saturation, initial water cut and final recovery based on the core permeability, oil viscosity and the initial oil saturation which is the first time to put forward this kind of chart and of the great significance to evaluate the recovery potential of the TZ.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

The different vegetable oils used in canned fish as filling medium have a preserving effect and contribute to the palatability of the product. In this study, the colour of European eels and the filling medium (sunflower oil, olive oil or spicy olive oil) was measured at different steps of the canning process. The sensorial characteristics of canned eels packed in the different oils were also evaluated. Colour scores (CieLab values) were higher in canned eels packed in sunflower and spicy olive oil than in canned eels packed in olive oil. The changes in colour parameters depended on the type of oil, the stage of the process and the storage time. Colour changes in canned eels packed in olive oil were highest during the sterilization process. Spicy olive oil was the filling medium in which the colour change was greatest, probably due to the migration of some of the spice components into the oil. Organoleptic properties were directly related to the type of oil used as the filling medium. The canned eels packed in sunflower oil were those awarded the highest scores in consumer tests, although the preferences varied depending on the age and gender of the consumers.

Drug-resistance represents one of the great plagues of our time worldwide, largely limiting the treatment of common infections, and accounting for the urge in the development of new antibiotics or other alternative approaches. Noteworthy, the indiscriminate use of antibiotics is mostly responsible for the selection of mutations that confer drug-resistance to microbes. Recently, beyond molecules of natural origin and synthetic ones studied to tackle microbial infections, ozone is raising interest for its unique biological properties, in particular when dissolved in natural oils. In fact, ozonated oils have been reported to act in a non-specific way on microorganisms hindering the acquisition of advantageous mutations resulting in resistance. Here, we focused on comparing the antimicrobial effect of two different types of ozonated oils over a panel of opportunistic and pathogenic microbes. Ozonated olive (OOO) and sunflower seeds (OSO) oils were preliminarily characterized by chemico-physical investigation and tested by in-vitro experiments. Candida albicans, Enterococcus faecalis, Staphylococcus aureus, Klebsiella pneumoniae, Pseudomonas aeruginosa and Escherichia coli have been challenged with different ozonated oils concentrations to evaluate their antimicrobial profile by agar diffusion and broth dilution methods. Cytotoxicity was also evaluated in keratinocytes and endothelial cells. Overall, our results revealed that both OOO and OSO showed a potent microbicidal effect especially against C. albicans (IC50 = OOO: 0.3 mg/mL and OSO: 0.2 mg/mL) and E. faecalis (IC50 = OOO: 0.4 mg/mL and OSO: 2.8 mg/mL) albeit exerting a certain effect also against S. aureus and E. coli. Moreover, both OOO and OSO do not yield any relevant cytotoxic effect at the active concentrations in both cell lines indicating that these ozonated oils are not toxic for mammalian cells despite exerting a potent antimicrobial effect on specific microorganisms. Therefore, OOO and OSO may be considered to integrate standard therapies in the treatment of common infections, likely overcoming drug resistance issues.

This study investigates multiple extrusion regimens with twin screw extruder for valorising soy press cakes (by-products of soy drink & tofu manufacturing process) by varying physical conditions of extrusion (temperature and moisture content) for improving their morphological, physico-chemical, technological, and sensory parameters. Valorised soy press cakes were compared before and after extrusion. Four extrusion regimens (moisture content 30%-60% and temperature 110°C -120°C) were designed for producing different extruded samples. Small amounts (3%-6%) of untreated and extruded press cakes were utilised in the development of meat analogues. All samples showed comparable nutritional and trypsin inhibition activity with almost all samples possessing most essential amino acids above significant amounts. Press cakes with higher moisture indicated improved bulk density, water holding and oil holding capacity. Interestingly, the same samples also reportedly had texture more closely resembling native meat texture and scored the highest in overall sensory acceptance. Our results thus indicate that soy press cake samples from drink manufacturing process, when extruded with the regimen with 60% moisture and temperature of 120°C show the greatest potential in developing meat analogues.

In the implementation of thermal enhanced oil recovery (TEOR) techniques, the temperature impact on relative permeability in oil - water systems is of special concern. Hence, developing a fast and reliable tool to model the temperature effect on two-phase oil - water relative permeability is still a major challenge for precise studying and evaluation of TEOR processes. To reach the goal of this work, two promising soft-computing algorithms, namely Group Method of Data Handling (GMDH) and Gene Expression Programming (GEP) were employed to develop reliable, accurate, simple and quick to use paradigms to predict the temperature dependency of relative permeability in oil - water systems (K_rw and K_ro). To do so, a large database encompassing wide-ranging temperatures and fluids/rock parameters, including oil and water viscosities, absolute permeability and water saturation, was considered to establish these correlations. Statistical results and graphical analyses disclosed the high degree of accuracy for the proposed correlations in emulating the experimental results. In addition, GEP based correlations were found to be the most consistent with root mean square error (RMSE) values of 0.0284 and 0.0636 for K_rw and K_ro, respectively. Lastly, the comparison of the performances of our correlations against those of the preexisting ones indicated the large superiority of the introduced correlations compared to previously published methods. The findings of this study can help for better understanding and studying the temperature dependency of oil - water relative permeability in thermal enhanced oil recovery processes.

Aqueous enzymatic method is a green oil extraction technology with limited industrial application owing to the need for demulsification of the oil body intermediate product. Existing demulsification methods have problems including low demulsification rates and high costs, such that new methods are needed. Free fatty acids produced by lipid hydrolysis can affect the stability of peanut oil body (POB) at a certain concentration. After screening even-carbon fatty acids with carbon chain lengths below ten, caproic acid was selected for demulsification of POB using response surface methodology and a Box–Behnken design. Under the optimal conditions (caproic acid concentration, 0.22%; material-to-liquid ratio, 1:4.7 (w/v); time, 61 min; and temperature, 79 C), a demulsification rate of 97.87% was achieved. Caproic acid not only adjusted the reaction system pH to cause aggregation of the POB interfacial proteins, but also decreased the interfacial tension and viscoelasticity of the interfacial film with increasing caproic acid concentration to realize POB demulsification. Compared with pressed oil and soxhlet-extracted oil, the acid value and peroxide value of caproic acid demulsified oil were increased, while the unsaturated fatty acid content and oxidation induction time were decreased. However, the tocopherol and tocotrienol contents were higher than those of the soxhlet-extracted oil. This study provides a new method for the demulsification of POB.

This study aimed to determine whether camelina oil is safe for use in canine diets, using canola oil and flax oil as controls as they are similar and generally regarded as safe (GRAS) for canine diets. Thirty privately-owned adult dogs of various breeds (17 females; 13 males), with an average age of 7.2 ± 3.1 years (mean ± SD) and body weight (BW) of 27.4 ± 14.0 were used. After a 4-week wash-in period using sunflower oil and kibble, dogs were blocked by breed, age, and size, and randomly allocated to one of three treatment oils (camelina (CAM), flax (FLX), or canola (OLA)) at a level of 8.2 g oil/100g total dietary intake. Body condition score (BCS), BW, food intake (FI), and hematological and select biochemical parameters were measured at various timepoints over a 16-week feeding period. All data were analyzed with ANOVA using PROC GLIMMIX of SAS. No biologically significant differences were seen between treatment groups for BW, BCS, FI, hematological and biochemical results. Statistically significant differences noted among some serum biochemical results were considered small and due to normal biological variation. These results support a conclusion that camelina oil is safe for use in canine nutrition.

In response to global climate challenges and the increasing demand for energy, exploring renewable energy alternatives has become crucial. Bio-oils, derived from biomass pyrolysis, are emerging as potential replacements for fossil fuel-based liquid fuels. This paper shares findings from the Institute of Energy and Fuel Processing Technology on the quality of crude biomass pyrolysis bio-oil samples. These findings highlight their potential as motor liquid fuels. The article details the results of tests on the physicochemical properties of four distinct bio-oil samples. Additionally, it presents preliminary test results on the hydrodeoxygenation of bio-oils in a batch reactor. The production of homogeneous, stable mixtures using other fuel additives, such as diesel oil, rapeseed methyl ester (RME), and butanol, is also discussed.

In this paper, the main characteristics of the natural bitumen of the Munaily-Mola oil sands were studied with comparison crude oil of Karazhanbas oil field. During the experiment, the density, heating value, ash content and elemental composition of natural bitumen were determined, and these parameters were compared with the properties of Karazhanbas crude oil. As well as oil, resin and asphaltene fractions of both hydrocarbons were separated and each of them were analyzed at a Fourier transform IR-spectroscopy Spectrum-65 with 450-4000 cm−1 range. According to these indicators, it is concluded that natural bitumen is a heavy hydrocarbon raw material with highly resin-asphaltene compounds. Like Karazhanbas oil, natural bitumen can be used as a raw material for various petrochemical products. By finding ways of effective processing of natural bitumen, it can be used in useful areas of the national economy.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

The article presents the influence of ecological agents, i.e. the effective microorganisms and silver compounds addition to lubricating oil on operating parameters of an internal combustion engine. The basic diagnostic parameters of a piston engine determining its technical condition were described. In the further part, the research stand and materials were presented. In the main part of this article for pure oil compared to oil with the effective microorganisms and silver compounds addition were shown. It was found that the addition of effective microorganisms and silver compounds to the oil reduces the emission of toxic components into the atmosphere along with the exhaust gases, while the remaining engine operating parameters for each load value show that these additives do not cause deterioration of the technical condition of the tested engine. Of all the agents used, the best results are obtained with the addition of ceramic tubes, because it is an additive that does not affect the properties of the oil in its composition. The advantage of ceramic tubes is the slow release of effective microorganisms, which has an effect on the parameters of the oil and thus on the operation of the engine. In further research, it will be checked how these additives affect the anti-seize and anti-wear properties of the lubricating oil used, which should give a broader view of the impact of these additives on the technical condition of the operated piston engine.

Several studies have highlighted the importance and evolution of process safety leadership and culture in various industries. However, none has focused on the palm oil milling industry yet. This paper critically reviews the latest developments in the palm oil milling process and unit operations leading to process safety concerns. It also discusses the Principle of 3C that is applied to explain repeat accidents and the four-level safety culture in the palm oil milling industry. For this purpose, the author presents case studies of two key palm oil companies in Malaysia. Overall, this paper offers guidelines to leaders in the palm oil milling industry about the required process safety leadership and culture to be understood in order to improve their safety outcomes.

Lipid nanoparticles have an interesting part of drug delivery system. In this study, the modification of the convention nano-lipid based soybean lecithin was demonstrated. Ginger oil derived Zingiber officinale was used along with lecithin, cholesterol and span 80 to fabricate nano-lipid (GL nano-lipid) using thin-film method. Through TEM and confocal microscope, GL nano-lipid exposes the liposome- like morphology. The average size of the resultant nanoparticles was 249.1nm with monodistribution (PDI= 0.021). The ζ-potential of GL nano-lipid was negative as similar to as prepared nano-lipid based lecithin. GL nano-lipid express the highly stable over 60 days of storage at room temperature in term of size, ζ-potential. A shift of pH value from alkaline to acid was detected in lecithin nano-lipid, while with the incorporation of ginger oil, pH value of nano-lipid dispersion was around 7.0. Furthermore, due to the rich of shogaol-6 and other active compounds in ginger oil, the GL nano-lipid is endowed with intrinsic antibacterial feature. In addition, the sulforhodamine B (SRB) assay and live/dead imaging revealed the excellent biocompatibility of GL nano-lipid. Notably, GL nano-lipid was capable to carry the hydrophobic agents as curcumin and perform a pH-dependent release profile. A subsequent characterization are a suitable potential for drug delivery system.

A framework for the review of existing water management systems and their transformation into robust water sharing systems is offered. The framework focuses on the need to develop efficient and equitable ways to manage water scarcity and plan to deal with the tensions scarcity imposes on any community. The framework identifies a way to bring together traditional community-managed systems with those typically used to allocate water to large water users and more commonly found in developed countries. So that use can be kept within sustainable limits while optimizing use, the framework includes mechanisms that enable the reallocation of water as demand and supply conditions change. Non-consumptive uses are recognized and environmental objectives can be delivered efficiently. Compliance with well-established accounting and hydro-logical concepts. Ways to increase the value of existing entitlements, encourage innovation and protect investments are included as options. It is recognized that the governance and legal arrangements necessary to underpin successful implantation are context specific.

Palm oil production involves unit operations that lead to greenhouse gas emissions. A typical mill is estimated to produce greenhouse gas emissions of 637–1,131 kg CO2 eq/t crude palm oil. There has been a huge effort to reduce the carbon footprint of palm oil mills. However, the data from such research have not been consolidated. This paper reviews significant information, results, and conclusions derived from studies in the literature. The latest developments in palm oil milling operations and information on greenhouse gas emissions are presented. Current initiatives in reducing carbon footprint of palm oil mills are discussed along with an assessment of the technologies employed. These include the conventional method of capturing biogas from palm oil mill effluent and emerging approaches such as converting palm sludge oil into biodiesel, deploying enzyme-assisted oil extraction, and converting biomass into fuel for energy generation as an alternative to coal and other fossil fuels. The importance of self-sufficiency is deliberated because a self-sufficient palm oil mill is estimated to reduce emissions by 457 kg CO2 eq/t crude palm oil compared to a mill that requires an external power supply. Methods with the greatest positive effect on the carbon footprint are identified for further investigation.

Fresh potatoes were deep-fried in olive oil (OO) & extra virgin olive oil (EVOO) and their blends with 5%, 10% and 20% v/v sesame oil (SO). This is the first report on the use of sesame oil as natural source of antioxidant for olive oil deep-frying. Oil was evaluated for Peroxide Value (PV), Free Fatty Acids (FFA), K₂₃₂, K₂₇₀, Trolox Equivalent Antioxidant Capacity (TEAC) and Total Phenols (TP) until Total Polar Compounds (TPCs) reached 25%. Sesame lignan transformations were monitored through Reverse-phase HPLC. While TPCs in olive oils increased at a steady rate, the addition of 5%, 10% and 20% v/v SO created a time window lasting 1, 2 and 3 hours, respectively, where TPCs were constant. SO addition to OO increased the total frying time. Furthermore, the addition of SO reduced the peroxides formation rate for both OO and EVOO. EVOO was more resistant to oxidation than OO as measured by TPCs and TEAC, while frying time raised from 21.5 to 25.25 h when EVOO replaced OO. The increase in frying time for olive oil but not for extra virgin olive oil, after SO addition, is pointing out a niche market for extra virgin olive oil in deep-frying.

This article focuses on the issue of motor oils used in the engines of off-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentration of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, glycol, and the products of oxidation, nitration, and sulphation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss for calculated in the paper.

Oriental lacquer, a natural and renewable polymeric coating, comes from the sap produced by lacquer trees. For practical application, oriental lacquer must be refined to reduce excess water and enhance its quality. In this study, drying oils were blended with oriental lacquer during the refining process to prepare an oil-modified refined lacquer (OMRL). The type and adding amount (0, 10, and 20% by wt.) of drying oils for wood coatings utilization were evaluated. Rhus succedanea oriental lacquer is composed of 54.1% urushiols, 34.3% water, 7.2% plant gum, and 4.4% nitrogenous compounds, and drying oils, including tung oil (TO), linseed oil (LO), and dehydrated castor oil (DCO) were used as materials in this study. The results show that the drying oil acts as a diluent, which reduces the viscosity and enhances the workability and could shorten the touch-free drying time and speed up the hardened drying of the OMRL. The results also indicate that the hardness, mass retention, Tg, tensile strength, abrasion resistance, and lightfastness of OMRL films decrease as more drying oils are blended. Conversely, the bending resistance, elongation at break, impact resistance increase, and particularly, the gloss, is greatly improved through the blending of more drying oils. In conclusion, the LO-modified refined lacquer (RL) has the highest film gloss and the DCO-modified RL has the shortest drying time for coating; otherwise, the film properties are similar among the three types of drying oil.

Oil pollution of extraction areas is an undesirable phenomenon, but very present, es-pecially in old farms. In the context in which the depollution of these areas, in Roma-nia, is carried out from public funds, this fact is more and more difficult to achieve. That is why the effect of pollutants on the environment is being analyzed more and more, it often remains that the depollution is done naturally. This material analyzes the effect of metals present in crude oil (Cu, Pb, Zn, Ag, Ni, Mn, As, Cd, V, Cr, S), on the soil affected by a historical accidental pollution in the Moinesti area, Romania. This article presents the results of analyzes performed by metal detection techniques, namely optical emission spectrophotometry with inductive coupled plasma and atomic absorption spectrophotometry. The metals determined in the polluted soil were statis-tically analyzed regarding the dispersion, standard deviation and coefficient of varia-tion compared to the control sample and compared with the results from two areas in Romania. The risk of exploitation of polluted areas was also analyzed, namely the method of pollution indices and the method of combining the effects of pollutants

Alzheimer's disease is characterized by a progressive decline of cognitive functions. The class of drugs used for the treatment are acetylcholinesterase inhibitors. Essential oils have contributed to folk medicine and discovery of new drugs for a long time. The purpose of the study was to investigate the in vitro and in silico the anti-acetylcholinesterase activity, as well as acute toxicity of the essential oil of Lippia origanoides. EOLO was obtained by hydrostelting and analyzed by gas chromatography-mass spectrometry. The inhibition assay of acetylcholinesterase enzyme activity was evaluated in vitro, as well as in silico by docking. The effects of EOLO on hematological, biochemical and behavioral parameters were analyzed in mices. We expose that EOLO shows good anti-acetylcholinesterase activity and low toxicity, possibly resulting from the action of the majority compounds thymol, carvacrol and p-cymene. The anti-acetylcholinesterase potential in vitro demonstrating a 70% inhibition. The docking results elucidated the participation of the major phenolics in AChE inhibition by interacting with the catalytic cavity of AchE. The acute oral toxicity test classified as low toxicity. These results contribute to expand the knowledge about essential oil of Lippia origanoides. Therefore, appears to be promising for herbal medicine production with anti-acetylcholinesterase and antioxidant activity.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

Through the process of paradigm change (water as a resource towards water as a common), the authors examine, from a theoretic point of view, the water governability proposed by Agenda del Agua Cochabamba (AdA) – Cochabamba Water Agenda – in the Cochabamba Valley (Bolivia), identifying barriers and drivers to the process that could take place. The rise of Evo Morales in Government in 2006 suggested that policy making would somehow take a fundamental turn resulting in more poor environmental-oriented water policies. However, if that was indeed the case, the implementation of these policies remain controversial as strong power asymmetries still exist at a local level that interfere with national policies shaping the political area. The Cochabamba Water Agenda echoes this debate on the political arena and contributes a politically contested water management through a paradigm change envisaging the difficulties through its implementation. The question remains if this “political” solution to paradigm change in water management may reduce water conflicts.

Water scarcity is a significant challenge facing Jordan today. It is a challenge in all areas that use water, and it has become certain that water is the critical factor in the population/resources equation. The water resources in Jordan have become limited with the noticeable increase in the population, mostly resulting from forced migrations in neighboring countries because of the wars and until our time. The rising natural population growth rate, along with the massive influx of refugees, has turned into a state of disproportion between the daily consumption of the population and the amount of water available. That Jordan shares most of its surface water resources with neighboring countries has exacerbated the situation. The current use of water already exceeds its renewable supply. Excessive withdrawal from aquifers, which leads to a lowering of the water table and deterioration in water quality, covered the deficit. This paper focuses on assessing the water situation in Jordan, mainly evaluating this problem and the solution being considered, the true basis for a sustainable water solution requires awareness by the population, and several governmental and non-governmental organizations are actively involved in educating residents about water shortages. The most important and 'actionable' elements of comprehensive water solutions are discussed in this paper, and these elements exist, develop extra water supplies, water harvesting, water desalination, proper wastewater reuse in the agricultural sector, and reduce the demand for drinking water. This research provides specific recommendations to address the shortage of water resources in the Kingdom and highlights the importance of water conservation and optimal use.

The growing need for water has pressured society and governments to focus more on preservation, planning and management of this natural resource, in which is fundamental to ecosystems and especially to humans. In this sense, the goal of this study was to analyze the national policy of water resources in Brazil and Italy, figuring out aspects that could promote its improvement, aiming at the preservation of water sources, guaranteeing satisfactory quantity and quality. They were carried out in 2019 by the environmental agencies of both countries, listing the main disciplinary regulations. The results show that although they are countries with different realities, they resemble similarities in managerial aspects of water resources, with legislation addressing qualitative and quantitative aspects of water, with guiding principles, instruments and actions aimed at the defence of this natural resource.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Most developing countries with petroleum resources are constrained in the ability to refine their oil and gas resources. This virtually results in the involvement of the International Oil Company (IOC) by the National Oil Company (NOC) of a particular nation to enter into an agreement to achieve the production of oil based on an agreed framework. However, in cur-rent development, there is little focus on the contractual agreement, particularly on the pro-duction sharing agreement by the IOC in the exploration of petroleum resources of developing countries. The primary objective of this paper is to critically explore the contract structure of production sharing agreement by the IOC in the exploration and development of petroleum resources in developing countries. Content analysis was used as the methodology of the study after examining several literatures. The findings indicate that the contract structure of the production sharing agreement (PSA) between NOC and IOC plays a significant role in the cost and risk of exploration and development of oil. In addition, it is noted that the joint committee of the NOC and IOC plays a paramount role in monitoring the operations of PSA between the NOC and IOC. Hence, from the gross oil production, the NOC gets its share as profit while IOC gets its share income tax. As an instrument of contract structure in the oil and gas sector, PSA needs further entrenchment between IOC and NOC to avoid likely issues that can emanate between the two parties in the face of current developments.

Mexico is currently facing important water management challenges. Cities in the country are facing water scarcity and at the same time, they struggle with floods during the raining season. The water sensitive urban design (WSUD) approach has proved to be helpful in tackling urban water challenges such as floods and water scarcity and it is being implemented in cities around the world. The WSUD approach highlights the role of both the water cycle and the water utilities systems, when transitioning towards a water sensitive stage. Therefore, the objective of this research is to analyse the current situation of the water cycle and the water utility (SIAPA). To do so, we have selected the Metropolitan Area of Guadalajara (MAG) and proposes a case study approach. Within our case of study, we answer two questions: 1) What are the causes of water scarcity and flooding in the MAG? and 2) What are the proposals to solve these problems under a WSUD approach? By answering these questions, we identified that the water management in the MAG corresponds to a single purpose infrastructure. This type of management does not contribute to solve the problems of water scarcity and floods. The water supply policy is based only on the construction of large dams disregarding the storage and use of rainwater, and reuse of greywater, and water-conservation devices. In order to transition towards a water sensitive stage, a WSUD approach that includes multi-purpose infrastructure should be considered. Such as green roofs, swales, rainwater gardens, infiltration trenches, etc.

Background Legionella pneumophila is one of the causes of legionellosis. Water environments serve as the natural habitat and the main sources of Legionella pneumophila. Objectives The aims of this study was to understand the differences of Legionella pneumophila serogroups distribution in well water, tap water, ice cubes, hospital and hotel water in East Java-Indonesia. Methods a total of 60 water samples in east java-Indonesia; from well water (n=25), tap water (n=5), ice cubes (n=5), water from the hospital (n=16), and hotel water (n=9) were detected using polymerase chain reaction with mip gene spesific primers and then it was analyzed by phylogenetic tree. Results For the 60 water samples collected in East Java, 12% of the samples (7/60) were positively contaminated by L. pneumophila. In details, there was 8% of the well water samples (2/25), 2% of the tap water samples (1/5), 2% of the ice cubes samples (1/5), 0% of the hospital water samples (0/16) and 33.33% of the hotel water samples (3/9). The phylogenetic tree showed that Legionella pneumophila contaminating well water isolate 1 from Surabaya and tap water isolate from Sidoarjo was closer to L.pneumophila serogroup 2, 4, 6, 8, 10, 12, isolates from Brazil, China, Spain and Australia. L.pneumophila contaminating the ice cubes from Sidoarjo was closer to serogroup 1, 2, 4, 7, 8, 11, 13, 14, while the bacteria contaminating well water isolate 2 from Sidoarjo as well as water in hotel of Surabaya (hotel water isolate 1, 2 and 3) classified into their own group. Conclusion There is a difference in the distribution of L. pneumophila serogroups between well water, tap water, ice cubes, and hotels.

Abstract: The effect of some weather parameters (rainfall and temperature) on the production of oil palm in Peninsular Malaysia was investigated. Data were analysed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, time series analysis, and multiple linear regression (MLR) carried out. SPSS and Microsoft Excel 2010 were used to analyse the results. The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature and rainfall (independent variables). The regression output returned three components; regression coefficients, regression statistics and ANOVA. The findings of the study revealed medium to high rainfall variability at the rate of 0.0008. This implies that rainfall is increasing over time with variations in its amount and intensity. As rainfall increases oil palm FFB production is predicted to increase at a slow rate of 0.0009. The estimation of average annual temperature indicated an increase of 5.6℃ at the rate of 0.0357℃ per year with a temperature maximum of 32.01℃ and minimum of 25.45℃. The result also revealed an increase in oil palm yield at the rate of 0.2581 per year with a mean value of 176247.6. Overall, there is a significant difference in the impact of rainfall and temperature on oil palm yield. This signifies that rainfall has a significant impact on oil palm yield (FFB) compared to temperature.

This study determines the management of downstream oil palm development in the technopolitan areas of Pelalawan Regency. The study object was analyzed qualitatively in stages, including the development, potential, and management of downstream oil palm. The results show that the downstream oil palm facilitates the development of various ideas, innovations, and knowledge from the use of products with high selling value. This supports the government, academia, business, and society in implementing Good Agricultural Practice (GAP). The downstream oil palm development in Pelalawan Regency is managed in an integrated, competitive, and sustainable manner. This allows all stakeholders and society (independent smallholders) to receive economic, social, and environmental benefits.

Oil spills are adverse events that may be very harmful to ecosystems and food chain. In particular, large sea oil spills are very dramatic occurrence often affecting sea and coastal areas. Therefore the sustainability of oil rig infrastructures and oil transportation via oil tankers are linked to law enforcement based on proper monitoring techniques which are also fundamental to mitigate the impact of such pollution. Within this context, in this study a meaningful showcase is analyzed using remotely sensed measurements collected by the Synthetic Aperture Radar (SAR) operated by the COSMO-SkyMed (CSK) constellation. The showcase presented refers to the Deepwater Horizon (DWH) oil incident that occurred in the Gulf of Mexico in 2010. It is one of the world's largest incidental oil pollution event that affected a sea area larger than 10,000 km². In this study we exploit, for the first time, dual co-polarization SAR data collected by the Italian CSK X-band SAR constellation showing the key benefits of HH-VV SAR measurements in observing such a huge oil pollution event, especially in terms of the very dense revisit time offered by the CSK constellation.

The biophenol integral extraction protocol from vegetation water developed in the early 2000s for the three-phase olive mill was adapted to a large two-phase mill operating in Sicily during the 2016/2017 season. The new set-up allows extensive recovery of olive phenolics, transforming previous waste into a source of revenues for the milling company and of valued bioproducts for its bioeconomy partner, while eliminating a source of potential pollution altogether.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

Engine oil degradation and tribological properties are strongly interrelated. Hence, understanding the chemical processes resulting in additive depletion and degradation products is necessary. In this study, in-service engine oils from petrol and diesel vehicles were analyzed with conventional and advanced methods (mass spectrometry). Additionally, the effect of the utilization profile (short- vs. long-range) was studied. Petrol engine oils generally showed accelerated antioxidant and antiwear degradation and higher oxidation, especially in case of a short-range utilization profile, which can be attributed to the higher air-to-fuel ratio (more rich combustion) compared to diesel engines. A detailed overview of oxidation and nitration products, as well as degradation products resulting from zinc dialkyl dithiophosphate and boron ester antiwear additives, diphenylamine antioxidants and salicylate detergents is given. A side-reaction between oxidation products (aromatic carboxylic acids) and the boron ester antiwear is highlighted. This reaction was only detected in the petrol engine oils, where the oxidation products were measured in a high abundance. However, no side reaction was found in the samples from the diesel vehicle, since there the aromatic carboxylic acids were largely absent due to lower oxidation.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

The world will experience an estimated 40% freshwater supply shortage by 2030, converting water scarcity into one of the principal global challenges that modern society face. Urban water-reuse is recognized as a promising and necessary measure to alleviate the growing water stress in many regions. The transformation to widespread application of water-reuse systems requires major changes in the way water is governed, and countries such as Spain already find themselves involved in this process. Through the systematic assessment of the city of Sabadell (Spain), we aim to identify the main barriers, opportunities and transferable lessons that can enhance governance capacity to implement systems for non-potable reuse of treated wastewater in cities. It was found that continuous learning, the availability and quality of information and level of knowledge and strong agents of change are the main capacity-building priorities. On the other hand, awareness, multilevel network potential and implementing capacity are already well-established. It is concluded that in order to undertake a widespread application of water-reuse practices, criteria examining water quality according to its use need to be developed, independently of the water’s origin. The development and implementation of such a legislative frame should be based on the experience of local water-reuse practices and continuous evaluation. Finally, the need for public engagement and adequate pricing mechanisms are emphasized.

Water availability is a major constraint for spring wheat production on the western Loess Plateau of China. The impact of tillage practices on water potential, water potential gradient, water transfer resistance, yield, and water use efficiency (WUEg) of spring wheat was monitored on the western Loess Plateau in 2016 and 2017. Six tillage practices were assessed, including conventional tillage with no straw (T), no-till with straw cover (NTS), no-till with no straw (NT), conventional tillage with straw incorporated (TS), conventional tillage with plastic mulch (TP), and no-till with plastic mulch (NTP). No-till with straw cover, TP, and NTP significantly improved soil water potential and root water potential at the seedling stage and leaf water potential at the seedling, tillering, jointing, and flowering stages, compared to T. These treatments also significantly reduced the soil-leaf water potential gradient at the 0-10 cm soil layer at the seedling stage and at the 30-50 cm soil layer at flowering, compared to T. Thus, NTS, TP, and NTP reduced soil-leaf water transfer resistance and enhanced transpiration. Compared to T, the NTS, TP, and NTP treatments significantly increased biomass yield (BY) by 18, 36, and 40%, respectively, and grain yield (GY) by 28, 22, and 24%, respectively, with corresponding increases in WUEg of 24, 26, and 24%, respectively. These results demonstrate that NTS, TP, and NTP improved GY and WUEg of spring wheat by decreasing the soil-leaf water potential gradient and soil-leaf water transfer resistance and enhancing transpiration, and are suitable tillage practices for sustainable intensification of wheat production in semi-arid areas.

Calabar is a city where 65 per cent of people are living in poverty in informal settlements with low and decreasing access to improved water. In the low-income informal areas of the city, residents are being made responsible for securing their own water supply through several coping strategies. This paper explores the decreasing access to water and coping strategies to shortage in Calabar, Nigeria. It analyses two complementary pieces of data: (i) the households’ coping strategies and (ii) satisfaction with improved water services. A mixed method was introduced and data was collected via fieldwork at three settlements in Calabar. A household survey of 360 respondents, 27 in-depth interviews and 2 focus groups were conducted. Findings show that households engaged in different coping strategies to access water, including conservation (changing routine/reusing), purchasing (spent a significant proportion of their income on buying water) and pumping as a coping strategy. The household's tenure, socioeconomic status and water accessibility determines their decision to move if services are not provided. A crucial differentiation exists between a larger population being granted less access to water versus certain individuals receiving access to a greater quantity of water.

The aim were to determine the drinking water preferences of people applied to a family health center. This cross-sectional study was carried out from April 01st to May 31st, 2022. The data were evaluated using the chi-square test and percent ratios with a significant of P < 0.05. The mean age of all 432 respondents was 48.03±15.86. It was determined that those aged 31-45 had drunk more bottled water (p<0.01) and more spring water (p<0.001), that those aged 65 and over more purified water (p<0.001), that women more tap water (p<0.001), that married people had drunk more demijohn and tap water (p<0.001, each one), that divorced/widows had drunk more packaged and purified water (p<0.001, each one), that the illiterate/literate bottled water (p<0.001, per one), that those who had no income/people who lived on the state or municipal assistance only carboy water (p<0.001). This study suggests that the biggest factor that positively affected the drinking water preference was the packaging of the water. However, the drinking rates of mains water and spring water were quite low. Convincing the authorities to make the mains water drinkable is of great importance in terms of overcoming the public's distrust of mains water.

Water resources are under pressure because of human activities. Its management faces the challenge of enhancing long-term water security while minimizing undesirable economic, social, and environmental impacts along with its production chain. Since water and wastewater treatment plants are designed to maintain and conserve freshwater provisioning services, it is paramount to understand how it operates before proposing options for sustainability. At this point, the diagnosis phase claims for methods scientifically-based, systemic, and more objective to provide information for decision-makers towards strategic management of water resources. This work applies the five-sector sustainability model (5SenSu) to assess Brazil's twenty major water and wastewater treatment companies (WWTC) to quantify their sustainability levels that allow ranking procedures and the establishment of benchmarks for improvements. Under comparative basis, results identified the top-three sustainable companies, CORSAN, CASAN, and SANEPAR, which should be considered examples of best practices. Specifically, the following best-ranked companies in each sector within 5SenSu should be used as benchmark patterns for more oriented best practices: SANEAGO, sector 1; AGESISA, sector 2; CORSAN, sector 3; CASAL, sector 4; MA, sector 5. This work contributes to the advancement in modeling sustainability assessment of human-managed systems (applied in WWTCs in this present study) from a systemic and epistemologically rooted approach, avoiding shortcomings and misleading discussions on the sustainability issue. Quantifying sustainability of WWTCS from 5SenSu allows the identification of those sectors/indicators that requires immediate cleaner production practices by decision-makers to improve overall sustainability, besides identifying those companies more aligned with the requirements of UN SDGs.

This research contributes to the detailed discussion about the approach to secure, hygienic water and cleanliness in Uganda and its pastoral regions. The relationship between the sanitation and clean water access with destitution is also discussed. Although this document is not leading towards the policy recommendation but it is an overall idea of how Uganda progressed because of the provisions adopted by the government, local and international organizations, and NGOs, and how the country lacked before these steps taken. Most of the data mentioned is taken from the house surveys of a decade 2002-2013 alongside the qualitative data. Literature review is also considered and is divided in two sections: first included researches related to water accessibility and usage, while the second section included researches related to work done and progress for diarrheal diseases and sanitation. Afterwards, methodologies were discussed where, firstly, trends and then the limitations in access to the basic necessities of life that is clean water and hygiene are mentioned. At last, the implementations and how they affected the rural Ugandans was discussed.

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

Nowadays, the combination of fingerprinting methodology with friendly environmental and economical analytical instrumentation are becoming increasingly relevant in the food sector. In this study, a highly versatile portable analyser based on Spatially Offset Raman Spectroscopy (SORS) to obtain the edible vegetable oils (sunflower and olive oils) fingerprints was used to evaluate the capability of such fingerprints, obtained quickly, reliable and without any sample treatment, to discriminate/classify the analysed samples. After data treatment, not only HCA and PCA as unsupervised pattern recognition techniques but also SVM, kNN and SIMCA as supervised pattern recognition techniques, showed that the main effect over the discrimination/classification was associated to those regions of RAMAN fingerprint related to the free fatty acids content, especially oleic and linoleic acid. These facts allowed the discrimination attending to the original raw material used in the oil's elaboration. In all the model established, reliable qualimetric parameters were obtained.

Virgin coconut oil (VCO) is a functional food with important health benefits. Its economic interest encourages fraudsters to deliberately adulterate VCO with cheap and low-quality vegetable oils for financial gain, causing health and safety problems for consumers. In this context, there is an urgent need for rapid, accurate and precise analytical techniques to detect VCO adulteration. In this study, the use of Fourier Transform Infrared (FTIR) spectroscopy combined with Multivariate Curve Resolution - Alternating Least Squares (MCR-ALS) methodology was evaluated to verify purity or adulteration of VCO with reference to several low-cost commercial oils such as sun-flower, maize and peanut oils. Control charts were developed to assess the purity of oil samples using MCR-ALS scores values calculated from a data set of pure and adulterated oils. In addition, quantification models were developed using MCR-ALS with correlation constraint for adulterated coconut oil to assess the blend composition. Different data pre-treatment strategies were tested in order to best extract the information contained in the sample fingerprints, and the calibration models were optimised using a genetic algorithm (GA) to select the most important variables. The models gave satisfactory results in external validation procedure, with absolute errors of less than 4.6 % for samples adulterated with sunflower, maize and peanut oils.

This study is aimed at demonstrating application of vegetation spectral techniques for detection and monitoring of impact of oil spills on vegetation. Vegetation spectral reflectance from Landsat 8 data were used in the calculation of five vegetation indices (normalized difference vegetation index (NDVI), soil adjusted vegetation index (SAVI), adjusted resistant vegetation index 2 (ARVI2), green-infrared index (G/NIR) and green-shortwave infrared (G/SWIR) from the spill sites (SS) and non-spill (NSS) sites in 2013 (pre-oil spill), 2014 (oil spill date) and 2015 (post-oil spill) for statistical comparison. The result shows that NDVI, SAVI, ARVI2, G/NIR and G/SWIR indicated certain level difference between vegetation condition at the SS and the NSS were significant with p-value <0.5 in December 2013. In December 2014 vegetation conditions indicated higher level of significant difference between the vegetation at the SS and NSS as follows where NDVI, SAVI and ARVI2 with p-value 0.005, G/NIR - p-value 0.01 and GSWIR p-value 0.05. Similarly, in January 2015 a very significant difference with p-value <0.005. Three indices NDVI, ARVI2 and G/NIR indicated highly significant difference in vegetation conditions with p-value <0.005 between December 2013 and December 2014 at the same sites. Post—spill analysis show that NDVI and ARVI2 indicated low level of significance difference p-value <0.05 suggesting subtle change in vegetation conditions between December 2014 and January 2015. This technique is essential for real time detection, response and monitoring of oil spills from pipelines for mitigation of pollution at the affected sites in the mangrove forest.

Water plays a crucial role in maintaining plant functionality and drives many ecophysiological processes. The distribution of water resources is in a continuous change due to global warming affecting the productivity of ecosystems around the globe, but there is a lack of non-destructive methods capable of continuous monitoring of plant and leaf water content that would help us in understanding the consequences of the redistribution of water. We studied the utilization of novel small hyperspectral sensors in the 1350-2450 nm spectral range in non-destructive estimation of leaf water content in laboratory and field conditions. We found that the sensors captured up to 96% of the variation in equivalent water thickness (EWT, g/m²) and up to 90% of the variation in relative water content (RWC). These laboratory findings were supported by field measurements, where repeated leaf spectra measurements were in good agreement (R²=0.79) with a time-lagged change of tree xylem diameter. Further tests were done with an indoor plant (Dracaena marginate Lem.) by continuously measuring leaf spectra while drought conditions developed, which revealed detailed diurnal dynamics of leaf water content. We conclude that close-range hyperspectral spectroscopy can provide a novel tool for continuous measurement of leaf water content at the single leaf level and help us to better understand plant responses to varying environmental conditions.

Oil and petroleum are strategic resources of great importance to national security. Petroleum and hydrothermal gold deposits may form together, with similar evolutionary trends in their formation, migration, and enrichment. Petroleum reservoirs and gold deposits are closely coupled under certain geological conditions. The solubility of gold in crude oil and its forms of occurrence are important in determining the mechanisms of interaction between gold and petroleum and in facilitating the recovery of gold from gold-bearing petroleum. In this study, the occurrence of gold in crude oil from the Linnan Depression in the Bohai Bay Basin, China, was studied using inductively coupled plasma–mass spectrometry and X-ray photoelectron spectroscopy. Concentrations of gold in crude oil from the Linpan and Shanghe oilfields averaged 44.5 ppb, which is well above the minimum concentration required for hydrothermal gold mineralization. Gold has an affinity with carbon, oxygen, and sulfur, and its concentration in crude oil is positively correlated with total acid and sulfur contents. We speculate that gold may exist in crude oil as complexes with organic acids or thiols, with crude oil thus being a transport medium for gold.

Traditional olive orchards have been grown for thousands of years and still occupy most of the world’s olive cultivation area. To compete with olive oil produced in the higher-yielding intensive orchards, the oil from traditional orchards must be of high quality. We evaluated oil quali-ty—potential and actual (under commercial conditions)—and identified the stages in the pro-duction chain that reduce oil quality in the traditional sector in the Middle East region. Our findings show a clear negative impact of growers' traditional practices on both chemical and sensorial characteristics of the olive oil. The oil originating from the commercial process had higher free fatty acid and lower polyphenol and carotenoid contents, lower stability, lower pungency, fruitiness and bitterness, and a higher prevalence of organoleptic defects than oil originating from fruit picked from the same trees in the experimental procedure. The current, commonly harvesting technique of pole beating significantly increased fruit injury and fruit with mold, leading to a reduction in oil polyphenols and an increase in free fatty acid level compared to manual picking. After harvest, storing the fruit for more than 48 h in plastic bags reduced oil quality dramatically. The traditional olive orchard could potentially be a source of high-quality Extra Virgin Olive Oil. However, handling of the fruit—from the trees until the end of the oil-extraction process—is done incorrectly, adversely affecting oil quality.

Staphylococcus pseudintermedius (SP) is an emergent zoonotic agent associated with multidrug resistance (MDR). This work aimed to describe the antibacterial activity of four essential oils (EOs) and silver nanoparticles (AgNPs) against SP. Fifteen SP strains were tested. The four EOs, namely Rosmarinus officinalis (RO), Juniperus communis (GI), Citrus sinensis (AR) and Abies alba (AB), and AgNPs were used alone and in combination to determine the Minimum Inhibitory Concentration (MIC) and Minimum Bactericidal Concentration (MBC) against SP. All strains presented MDR and methicillin resistance. Among the antibiotic cohort, only rifampicin, doxycycline and amikacin were effective. When EOs were tested alone, AB showed the lowest MIC followed by GI, RO and AR (0.23%±0.3; 0.5%±0.51; 0.79%±0.39; 0.93%±0.63). MBC was increased with the following order: AB, GI, AR and RO (3.56%±4.87; 4.93%±6.27; 8.53%±7.2; 10.34%±5.31). MIC and MBC values for AgNPs were 10.74 mg/L±4.23; 261.05 mg/L±172.74. In combination, the MIC and MBC values were lower for all compounds. In conclusion, EOs and AgNPs could be considered as promising antibacterial alternatives to antibiotics.

This study develops an efficient, low-temperature process for formulating a nanoemulsion-based gel encapsulating Pituranthos tortuosus's essential oil, investigating its wound healing potential. The novel process ensured stable encapsulation of the medicinal plant's oil. The nanoemulsion was characterized using dynamic light scattering and transmission electron microscopy, followed by in vitro and in vivo tests to examine wound healing efficacy. Results revealed the gel's excellent stability, high encapsulation efficiency, and significant wound-healing effects. This research provides a new method for formulating Pituranthos tortuosus's essential oil nanoemulsion-based gel, emphasizing the potential role of plant-based therapies in healthcare advancement, and invites further exploration into the therapeutic applications of essential oil-encapsulating nanoemulsions.

Inflammation is the response of the immune system to infection and injury, with complex interactions with the body, tissues and cells, and plays an important role in the initiation and progression of many diseases such as cancer and cardiovascular disease. Traditional excipients functioning as drug delivery systems can reduce the side effects of systemic distribution of inflammatory drugs. Oil phase, a common excipient in nanoemulsions (NEs), has the advantages of assisting the formation of emulsions, loading lipophilic drugs, thermodynamic stability, wide sources, low price and easy availability. In particular, some of them, like linolenic acid and medium chain triglyceride (MCT), also function as inhibitors of systemic inflammation marker and vascular inflammation marker. However, the influences of different oil phases on the construction of NEs and their distribution in vivo have not been fully investigated. Herein, Tween 80 and ethyl alcohol were screened out as emulsifiers and co-emulsifiers, and three different oil phases used in clinical practice widely, including MCT, oleic acid (OA), and ethyl oleate (EO), were selected as the oil phase to prepare NEs delivery platform. Three NEs had consistent size, potential, morphology, excellent stability and mitochondrial localization function. Importantly, they exhibited superior cellular uptake capacity in inflammatory-injuried human umbilical vein endothelial cells and significantly targeted the brain, lung, heart and thoracic aorta in the lipopolysaccharide-induced mouse and zebrafish larvae inflammation models. Meanwhile, the fluorescence intensities of three NEs were different in these organs, suggesting that their differential enrichment might provide alternative delivery platform for disease treatment in the corresponding organs.

Edible films were produced combining pectin (P) matrix with chitosan nanoparticle (CSNP), polysorbate 80 (T80), and garlic essential oil (GEO) as an antimicrobial agent. The CSNP were analyzed for their size and stability, and the films, throughout their contact angle, scanning electron microscopy (SEM), mechanical and thermal properties, WVP and antimicrobial activity. Four filming-forming suspension were investigated: PGEO (control); PGEO@T80; PGEO@CSNP; PGEO@T80@CSNP. The average particle size was 317nm with zeta potential reaching +21.4 mV, which indicated colloidal stability. The wettability of the films exhibited values of 65°, 43°, 78°, 64° respectively. In antimicrobial tests, the films containing GEO showed inhibition only by contact for S.aureus. For E. coli, the inhibition occurred only in films containing CSNP and by direct contact in the culture. The results indicate a promising alternative for designing stable antimicrobial nanoparticles for application in novel food active packaging.

sustainability reporting, critical paradigm, upstream oil, and gasThe operating activities of the upstream oil and gas industry directly impact the environment. This industry faces significant social challenges and directly impacts the environment. Many Reputable international sustainability institutions organize sustainability awards. However, community conditions do not have a positive impact on sustainability practices. There are vari-ous serious violations related to sustainability, environmental pollution, multiple cases of cor-ruption, human rights, and other violations. In contrast, the companies receiving this award also received inspection findings of violations committed by The Audit Board of the Republic of In-donesia. This study uses critical discourse analysis that begins with phenomena related to viola-tions of sustainability reporting from scientific journals and other references using a systematic literature review approach over the last ten years. It produces a critical paradigm that is not val-ue-free, which is the basis for framing thought utilizing the theory of hegemony. The results of this study indicate that the upstream oil and gas industries are obliged to implement Corporate Social Responsibility (CSR) practices and Sustainability Reports (SR), has biased factors that are contrary to the sustainability concept and are not under the sustainability award based on evi-dence obtained from the stages of manuscript analysis with systematic literature review

Public key encryption methods are often used to create a digital signature, and where Bob has a public key and a private key. In order to prove his identity, he will encrypt something related to the message with his private key, and which can then be checked with his public key. The main current methods of public-key encryption include RSA and ECC (Elliptic Curve Cryptography), and which involve computationally difficult operations. But these operations have not been proven to be hard in an era of quantum computers. One well-known hard problem is the solving of quadratic equations with $m$ equations with $n$ variables. This is a known NP-hard problem, even in a world of quantum computers. These can be used as post-quantum signature schemes and which involve multivariate equations. In order to understand these methods, this paper outlines a simple example of implementing the oil and vinegar method, and where we have a number of unknown oil variables and a number of known vinegar variables, and where the vinegar variables help convert the hard problem into an easy one.

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil (WCO). Quality parameters such as the acid value, water content, and free and total glycerin content were evaluated and compared with those of commercial resins such as Magnesol® and Amberlite™. Promising results were obtained using sawdust during the purification process, achieving a 31.6% reduction in the acid value compared to that of unpurified biodiesel, the reduction was 31.3% more efficient than Amberlite™. Sawdust adsorbed free glycerin at 55.8%, being more efficient than Amberlite™. The total glycerin values were similar between commercial resins and sawdust. A water content values were similar than Amberlite™ and better than that with Magnesol®, at 4.3% and 39.81%, respectively. These results show that sawdust can be used as an alternative bioadsorbent in a dry purification method for biodiesel being a residue with less environmental impact.

To evaluate the efficacy of fish oil for protection against coronary heart disease (CHD), we conducted a systematic review and meta-analysis of randomized controlled trials (RCTs) evaluating the use of fish oil for protection against CHD. We retrieved relevant articles published from January 1966 to January 2020 by searching the PubMed, EMBASE, Cochrane CENTRAL, and Web of Science databases. RCTs of fish oil in preventing CHD were selected. The study quality was evaluated using the Cochrane Risk of Bias tool with RevMan 5.3 software. The first selection involved 350 citations. After screening and evaluation of suitability, 19 RCTs adjusted for clustering were included in the meta-analysis. All selected manuscripts considered that fish oil was effective in preventing CHD, secondary outcome measures included angina, sepsis and death. Compared with the control group, fish oil may confer significant protection against CHD (odds ratio = 0.84; 95% confidence interval: 0.72–0.98). There was no significant difference in the incidence of secondary outcomes between the observation group and the control group (P > 0.05). The above results show that fish oil plays an important role in reducing CHD and cardiovascular events. However, because of the suboptimal quality of the studies included into the meta-analysis, these results do not justify adding fish oils systematically to the heavy pharmaceutical assortment already recommended in CHD patients.

Resides derived from liquefaction of oil palm trunk in the presence of polyhydric alcohol with different liquefaction temperature and time were characterized to provide a new approach to understand some fundamental aspects of the liquefaction reaction. Higher temperature and longer reaction time resulted in lower residue content, indicating more decomposition of components of oil palm trunk. The amorphous polymer comprised of lignin, hemicellulose, starch, and cellulose with non-crystalline structure are firstly degraded at low liquefaction temperature, followed by the decomposition of crystalline region of cellulose. Although it was relatively difficult to destroy the ordered structure of cellulose, most of them could be liquefied via prolonging reaction time or enhancing reaction temperature. Nevertheless, it was found that re-condensation of liquefied products occurred during the liquefaction process when higher temperature of 180 oC was used after 60 min, leading to the gradual increase of residue content with increase of reaction time.

Oil floating on the sea surface can be detected by both passive and active methods using the ultraviolet-to-microwave spectrum, whereas oil immersed below the sea surface can signal its presence only in visible light. This paper presents an optical model of a sea area deeply polluted by an oil suspension (10 ppm) located in a layer (thickness 5 m) separated from the sea surface by a clear layer (thickness 1 m). The impact of wavelength and state of the sea surface on reflectance changes is shown based on the results of Monte Carlo ray tracing. A two-wavelength index of reflectance is proposed to detect oil suspended in the water column (645-469 nm).

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

Sachet water (SW) is a major source of drinking water in most Nigerian homes, thus making it a possible conveyance medium for health risks due to contamination rather than for replenishment of the body. This study collected SW from three busy neighborhoods and investigated for the presence of indicator bacteria – Escherichia coli (E. coli), Total Coliform (TC), Total Heterophilic Bacteria (THB), and Staphylococcus – and some physio-chemical parameters – total dissolved solids (TDS), pH, electrical conductivity (EC), and salinity. Multi-variable and exploratory statistical methods were applied to the results to determine correlations between bacterial contamination levels and perceived brand reputation. Bacteriological test with raw SW samples appeared too numerous to count (TNC) and thus required serial dilutions. After seven dilutions, results obtained revealed that SW brands with good reputation had no TC and E. coli and was statistically significant with groupings of other SW brands (χ2 = 12.28; p < 0.05 and χ2 = 37.96; p < 0.05) respectively. Additionally, SW brands with poor reputation had mean values of TC (19.7X10^8 cfu/ml;14X10^8 cfu/ml1.15X10^8 cfu/ml) and E.coli (18.2X10^8 cfu/ml;38.7X10^8 cfu/ml,32.4X10^8 cfu/ml) exceeding threshold value of zero set by the World Health Organization (WHO). Only one sample from poor reputation brand tested positive for Staphylococcus and was not statistically significant (χ2 =5.2191; p = 0.074). Principal Component Analysis (PCA)/ Factor Analysis (FA) revealed that most of the SW had fecal contamination in an alarming magnitude. Therefore, this study suggests that periodic cleaning of distribution lines, location specific treatment, QC and QA measures should be taken to reduce water security risk for SW consumption in the region.

Water pollution in Iraq has been extended disaster edge; this pollution is caused by wastes and sewages into soil and rivers, pollutant water sources influence the outbreak and serious epidemic status among the population.. The aim of this study is to determine the bacteriological quality of drinking water sources and characteristics of water-borne diseases especially diarrheal cases in Darbandikhan city. 166 water samples, collected from the different sources and areas, were tested for the presences of coliform bacteria as an indicator for pathogen contamination. Most probable number index was used for coliform enumeration. 161 diarrheal cases were taken as a sample from the patients were admitted to the general hospital in Darbandikhan district.. The questionnaire form was planned to view characteristics of diarrheal cases and patients were interviewed directly, the data was analyzed by STATA software application. 46% of the diarrheal cases used tap water for drinking. On the other hand, the reminder (54%) used other sources for the same purpose. All the risk factor such as type of water source, sufficiency of the water, duration of water storage and chlorination were associated with diarrhea. Almost half of the cases were children and three quarters were single. The data was analyzed by STATA version 13.1.This study indicated that the majority of drinking water sources in Darbandikhan city are not suitable for drinking, although net pipe system supplied chlorine significantly it has been proven that the tap water from the homes is not suitable for consumption.

Shanghai is experiencing water supply problems caused by heavy pollution of its raw water supply, deficiencies in its treatment processes and water quality deteoriation in the distribution system. However, little attention has been paid these problems of water quality in raw water, water treatment and household drinking water. Based on water quality data we show that the raw water sources of the Huangpu River and the Changjiang (Yangtze River) estuary are polluted by microbes (TBC), eutrophication (TP, TN and NH3-N), heavy metals (Fe, Mn and Hg) and organic contamination (chemical oxygen demand [COD], detergent and volatile phenols [VP]). The average concentrations of these contaminants in the Huangpu River are almost double that of the Changjiang estuary forcing a rapid shift to the Changjiang estuary for raw water. In spite of filtering and treatment, TN, NH3-N, Fe, COD and chlorine maxima of the treated water and drinking water still exceed the Chinese National Standard (GB5749). We determine that the relevant threats from water source to household water in Shanghai are: 1) eutrophication arising from highly concentrated TN, TP, COD and algal density in the raw water; 2) increasing salinity in the river estuary, especially at the Qingcaosha Reservoir (currently the major freshwater source for Shanghai); 3) more than 50% of organic constituents and by-products remain in treated water; 4) bacteria and turbidity increase in the course of water delivery to users. The analysis presents an holistic assessment of the water quality threats to metropolitan Shanghai in relation to the city’s rapid development.

Wind energy powered pumps could be an alternative to conventional fuel powered pumps for water abstraction because they rely on a free energy and they are environmentally friendly. The objective of this study was to assess the potential of wind energy to operate water abstraction systems in Teso sub-region of Uganda for livestock watering Daily mean wind speeds recorded at a height of 10 m for a period of ten years (2005–2015) were collected from Amuria and Soroti Meteorological stations in the study area. Data were analyzed using Weibull distribution to evaluate the annual wind speed frequency distributions and consequently assess their potential for water abstraction. The results indicated that warmer months (January, February and March) have higher mean wind speeds than the cold months (August, September and October). High wind speeds in the dry seasons corresponded to the periods of high water demand. The highest shape parameter (k) of 3.07 was registered in 2009 and scale parameter (c) of 3.78 in 2012. The highest wind power density of 43 W/m² was obtained the year 2012 while the lowest wind power density of 15.47 W/m² was obtained for Soroti district in the year 2009. The maximum power extractable in Amuria in 2012 was 324 W/m² which is potentially enough for water abstraction. Maximum discharges of 1.86 m³/s and 1.52 m³/s were obtained for Amuria and Soroti districts respectively at mean wind speeds of 5 m/s. Therefore, Teso sub region winds have potential for water abstraction and Amuria district better sites for livestock watering using wind energy.

Cleaning wastewater and using it again for secondary purposes is a measure to address water scarcity in urban areas. However, upscaling of recycled water schemes is challenging due to the possible emergence of various barriers. Based on a review of the governance literature we suggest that a set of five governance conditions is necessary for a successful upscaling of recycled water schemes; (1) policy leadership, (2) policy coordination, (3) availability of financial resources, (4) awareness of a problem, and (5) the presence of a public forum. In order to elaborate on the practical relevance of these conditions we studied a recycled water scheme currently being upscaled in Sabadell, Spain. We reviewed policy documents, conducted a set of 21 semi-structured interviews, and attended two policy meetings about the subject. Our results suggest that Sabadell meets the required conditions for upscaling reused water to a certain extent. However, the presence of a public forum is lacking. We discuss the implications of the absence of the venue and procedures for public participation in Sabadell and how it could be strengthened. Following this discussion, we conclude with some lessons for other cities that plan to upscale their recycled water schemes.

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

Virgin Argan Oil (VAO) is extracted from the fruits of the Moroccan endemic species argan [Argania spinosa (L.) Skeels]. It is known for its richness in polyunsaturated fatty acids and its unique composition in tocopherols conferring a panoply of pharmacological properties, documented in several studies. The aim of this study was to investigate the potential protective effect of VAO against oxidative and nitrosative stress induced in cells of the model species Tetrahymena pyriformis. As a comparison, well-known Virgin Olive Oil (VOO) from Olea europaea L. was used instead. Both oils were subjected to a preliminary analysis of phytochemicals and properties of interest. Oxidative stress in T. pyriformis cells was induced by hydrogen peroxide (H2O2) at 350µM, whereas sodium nitroprusside (SNP) nitrosative stress was induced using a 1mM concentration. Neither of these concentrations caused relevant changes in cell viability. The level of reactive oxygen species (ROS) was evaluated in the cell cultures by using H2-DCFDA dye. The activity and cell localization of the antioxidant enzymes catalase (CAT), superoxide dismutase (SOD) and glutathione peroxidase (GPX) was evaluated as well as the levels of glutathione (GSH) and the malondialdehyde (MDA) generated after lipid peroxidation. Finally, the presence and localization of intracellular lipid droplets was assessed by using Nile red. The treatment of cultures with H2O2 produced significant increases in the activity of CAT, SOD and GPX and in the level of GSH, as also did the SNP treatment. MDA level was increased by both the treatments. VAO and VOO treatment were found to protect T. pyriformis from oxidative stress and increased cells defense in nitrosative stress. In another hand VAO and VOO decreased significantly MDA level increased by H2O2 treatment and failed after SNP treatment. The quantification of fluorescence signal obtained from immunolocalization of antioxidant enzymes confirmed the results obtained after the evaluation of their activities. Interestingly the level of ROS and the number of lipid droplets increased by H2O2 treatment was significantly decreased by VAO and VOO co-treatments. VAO and VOO represent strong antioxidants, playing an important role in protecting cells against oxidative stress.

The Pingbei area is the main accumulation area of oil and gas in the Xihu Sag. The phase characteristics of oil and gas in this area are complex, and the understanding of their genesis is still unclear. In this paper, based upon discussions of crude oil and natural gas geochemical data, integrated with local geological features, we discuss the sources, migration, and phase state characteristics of oil and gas in the Pingbei area of the Xihu Sag. The study results showed that the crude oil and natural gas in the Pingbei area are coal-derived and the oil and gas produced by the humic organic matter during the maturity stage. The oil and gas source correlation showed that crude oil and natural gas have good affinity with the Eocene Pinghu Formation (PF) coal-bearing source rocks. Crude oil has the characteristics of near-source accumulation and short-distance migration while natural gas is supplied from a dual source: the coal-derived hydrocarbon rocks of PH in the deep part of the study area, supplemented by the coal-derived hydrocarbon rocks of PH on the bottom of the slope, and adjacent hydrocarbon-bearing sub sag. The distribution characteristics and geochemical migration indices of hydrocarbon showed that the oil generated from the hydrocarbon source rocks of PH in the deep Pingbei area mainly migrates vertically along the fault connecting the reservoir and the source rocks to the trap, where it accumulates, while the natural gas exhibits deep and large faults that mainly migrate vertically, supplemented by its lateral migration along the composite transport system composed of faults and sandstone layers in the slope zone. The mechanisms of produced, exhausted, and geochromatographic effects (PGE), as well as evaporative fractionation (EF) and phase-controlled migration fractionation (PMF), result in the obvious discrepancy of hydrocarbon’s properties on the vertical profiles.

Epidemiological studies have shown that consuming olive oil rich in phenolic bioactive compounds is associated with a lower risk of neurodegenerative diseases and better cognitive performance in aged populations. Since oxidative stress is a common hallmark of age-related cognitive decline, incorporating exogenous antioxidants could have beneficial effects on brain aging. In this review, we firstly summarize and critically discuss the current preclinical evidence and the potential neuroprotective mechanisms. Existing studies indicates that olive oil phenolic compounds can modulate and counteract oxidative stress and neuroinflammation, two relevant pathways linked to the onset and progression of neurodegenerative processes. Secondly, we summarize the current clinical evidence. In contrast to preclinical studies, there is no direct evidence in humans of the bioactivity of olive oil phenolic compounds. Instead, we have summarized current findings regarding nutritional interventions supplemented with olive oil on cognition. A growing body of research indicates that high consumption of olive oil phenolic compounds is associated with better preservation of cognitive performance, conferring an additional benefit, independent of the dietary pattern. In conclusion, the consumption olive oil rich in phenolic bioactive compounds has potential neuroprotective effects. Further research is needed to understand the underlying mechanisms and potential clinical applications.

Various methods of water purification, the aim of which is to obtain such a purity class that makes it suitable for consumption are presented in the article. It is a review of solutions, ranging from methods known and used for over 100 years, through research and experiments underway, to those that are only a concept. Some of the solutions are so effective that they should also be combined with the possibility of safe storage of purified water. Flexible tanks are used for this, which significantly improve logistics and provide a supply of water in all places where it is needed.

The occurrence of potential spikes in a cell is a sign of life, and it is called action potential. There is a common notion that neuron signal conduction is the conduction of action potential. Hence, action potential is a typical and essential life activity. However, such potential spikes occur even in simple nonliving systems. According to the experimental observations by Pollack, structured water molecules can generate a negative potential environment. From this observation, the potential spike generation process for both living and nonliving systems caused by ion and water molecule adsorption-desorption process could be explained in this paper. So, taking into consideration the electrically neutral water molecules,the action potential generation mechanism could be explained. It is a fully inanimate model. Hence, the action potential may not be a life activity. Here, the role of water molecules in life is investigated further. It was found that the phase transition of the membrane is involved in the neuron signal conduction, but the membrane phase transition could be due to the change of state of the water molecules, which forms a large-scale structure in the cavities created by a number of lipids.

Rapid technological advancements in information communication technologies have enabled water resource data collection at greater spatial and temporal scale. However, this water data is often limited to the purposes of its primary collection, and limits decisions made by stakeholders towards sustainable urban water management. This empirically focused research paper examines how water practitioners involved in strategic planning can capture additional values from integrating different water data. Furthermore, the perception of 22 urban water practitioners across Australia are presented, regarding the importance of and difficulty in using water data for strategic planning, and the necessary steps for achieving integrated water management practices. Interviewees perception revealed gaps in available water resource data (i.e. water quality, ground water, stormwater, and urban water use), and limitations of industry guidelines for operating within existing governance frameworks. Overall, the research highlights the Australian urban water sector’s perception of water data’s crucial role in representing stakeholders interest; however, changes made in water data’s collection are required for an integrated water management approach. Implications for future open water data standard are discussed.

Water scarcity is significantly increasing water stress in Africa and some parts of the world. This is due to human induced factors such as climate change, increase of human population that raises demand which outstrips food availability, and put great changes of land use which results in changes of hydrological mechanics and water availability as whole. The investigation was through literature review and it tries to examine the criticality of water scarcity in Africa regions, and the major factors that mastermind this menace. Also possible strategies that can be promptly used to manage water scarcity at domestic level and in agriculture are described in this paper, not with standing the fact that agriculture sectors in Africa and the rest of the world remain the utmost vulnerable enterprise to water scarcity and withdrawal on the planet earth.

Achieving water security and availability for all is among the principle agenda of the UN-Sustainable Development Goals. To achieve the goal of water security, particularly in rapidly expanding cities, identification of safe and sustainable water resources is an absolute necessity. The paper conducts an exploratory investigation in the hydro geochemical characteristics of groundwater and thereby, assess the suitability of groundwater as an alternative and reliable resource for public water supply in the Indian city of Surat. A total of 33-groundwater samples, selected on the basis of aquifer depth, land use signatures, were collected from open, bore, dug wells and hand pumps. After the hydrogeochemical analysis, the study evaluated the present state of the groundwater quality and determined the spatial distribution of groundwater quality parameters such as hardness, electrical conductivity, Cl −, pH, SO42-, and NO3 − concentrations. An interpolation technique, known as ordinary kriging, was used to acquire the spatial distribution of parameters of groundwater quality parameters. Based on the permeability index, result showed that 80% of the sampled groundwater quality falls under excellent class i.e. category I with PI value ranging from 1-24%, whereas the rest 20% of the samples has fallen under good class i.e. category II with PI value ranging from 25 to 75% on the suitability of water for irrigation. The results of this study outlines the unsustainability of groundwater for direct consumption, especially without any improved onsite water treatment, but it is appropriate for the irrigation purposes.

Oil spills may have devastating effects on marine ecosystems, public health, the economy, and coastal communities. Therefore, scientific literature contains various up-to-date, advanced oil spill predictive models, capable to simulate the trajectory and evolution of an oil slick generated by the accidental release from ships, hydrocarbons production, or other activities. To predict in near real time oil spill transport and fate with increased reliability these models are usually coupled operationally to synoptic meteorological, hydrodynamic, and wave models. The present study reviews the available different met-ocean forcings that have been used in oil spill modeling, simulating hypothetical or real oil spill scenarios, worldwide. Nine state-of-the-art oil spill models are critically examined in terms of the met-ocean data used as forcing inputs in the simulation of twenty-four case studies. Results illustrate that most oil spill models are coupled to different resolution, forecasting meteorological and hydrodynamic models, posing, however, limited consideration in the forecasted wave field (expressed as the significant wave height, the wave period and the Stokes drift) that may affect oil transport, especially at the coastal areas. Moreover, the majority of oil spill models lacks any linkage to the background biogeochemical conditions, hence, limited consideration is given in processes like oil biodegradation, photo-oxidation and sedimentation. Future advancements in oil spill modeling should be directed towards the full operational coupling with high-resolution atmospheric, hydrodynamic, wave, and biogeochemical models, improving our understanding in the relative impact of each physical and oil weathering process.

Hydrogenated water has emerged as a novel approach in the field of health and wellness. It is be-lieved to have potent antioxidant properties that can neutralize harmful free radicals in the hu-man body. It has also been shown to be beneficial in mitigating oxidative stress-induced damage through its anti-inflammatory and anti-apoptotic pathways. We aim to conduct a systematic re-view to evaluate the potential benefits of hydrogenated water. The review protocol was uploaded on PROSPERO. After the initial search criteria, the articles were reviewed by two blinded inves-tigators, and a total of 25 articles were included in the systematic review. The potential benefits of hydrogenated water on various aspects of health, including exercise capacity, physical endurance, liver function, cardiovascular disease, mental health, COVID-19, oxidative stress, and anti-aging research, are a subject of growing interest and ongoing research. Although preliminary results in clinical trials and studies are encouraging, further research with larger sample sizes and rigor-ous methodologies is needed to substantiate these findings. Current research needs to fully ex-plain the mechanisms behind the potential benefits of hydrogenated water. Continued scientific exploration will provide valuable insights into the potential of hydrogenated water as an adjunc-tive therapeutic approach in the future.

Fresh water is an increasingly scarce resource in both urban and rural developments. As a response to this challenge, non-potable water reuse is on the rise. This research explored a potential off-grid system for water purification, consisting of a staircase wetland with terracotta pot plants working as a filter for greywater. The study further investigated the physicochemical properties of the greywater and the soil before and after the wetland purification. Results showed that the filtered water satisfied all requirements for water reuse, e.g., pH, turbidity, and total coliforms. The research then uniquely investigated the effect of greywater on the soil biodiversity and soil biomass using soil DNA extraction and the tea bag index testing method. The filtered greywater absorbed by soil decomposed the soil faster and stabilized it better compared to tap water-absorbed soil or unfiltered greywater. The DNA generation sequencing revealed no significant differences in alpha diversity between control and treatment samples. The beta diversity differences were significant. This nature-based solution can lead to reduced load on the sewage system, resulting in less wastewater generation.

Computational Fluid Dynamics (CFD) is revolutionizing the oil and gas industry by offering powerful insights and innovative solutions. This paper explores the cutting-edge applications of CFD in enhancing and innovating within the sector. CFD simulations provide engineers with invaluable insights into fluid behavior, enabling optimized designs and informed decision-making. The software facilitates foresight by predicting system performance, optimizing drilling techniques, and maximizing reservoir management strategies. Moreover, CFD optimizes equipment design, increases operational efficiency, and reduces costs through virtual testing, eliminating the need for costly physical prototypes. The application of CFD aligns with the United Nations Sustainable Development Goals (SDGs), promoting energy efficiency, climate action, responsible production, and sustainable consumption. It addresses flow assurance challenges, enhances safety protocols, and mitigates environmental impacts. CFD is a powerful tool driving innovation, resilience, and sustainability within the oil and gas industry, ensuring a more efficient, safe, and environmentally conscious future. As advancements in CFD methodologies continue, the potential for further enhancements and breakthroughs within the sector becomes even more promising, driving the industry towards a sustainable and prosperous future.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.