Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

Growing population leads to industrialisation and urbanization which in turn generate huge amount of waste that represents a big problem for many developed and developing countries. Emerging solution for this problem can be use of wastes as a sustainable source of energy in the form of heat, electricity, fertilizer and biofuel like bioethanol. Type of technology employed is mainly based on the composition of waste whether it is rich in organic matter like MSW or not. WTE technologies reduce the volume of waste as well as decrease the dependence on fossil fuels for energy generation.This study focuses on overview of various available waste to energy conversion technologies like pyrolysis, gasification, incineration, biochemical treatments like landfill gas, aerobic and anaerobic digestion of wastes.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

Waste-to-Hydrogen (Wahh) is a process of converting waste into hydrogen gas through various methods such as thermal conversion, biological conversion, and chemical conversion. This process not only helps in managing waste but also provides a clean source of energy as hydrogen is a renewable energy source that produces zero greenhouse gas emissions during combustion. Wahh has the potential to provide a sustainable solution for energy generation and waste management in the current scenario of globally increasing energy demands. This study aims to examine the properties and energy efficiencies of various renewable fuels including fuelwood, biogas, biomethane, and biohydrogen with a specific focus on differentiating the characteristics of biohydrogen. The paper explores the emerging concepts of waste-to-hydrogen microgrids, biohydrogen refineries, biohydrogen prosumer networks, and a biohydrogen circular economy, as well as Public-Private-People Partnerships (4Ps) and the hydrogen-centric renewable energy revolution, which are taking shape in industrialized countries. The study presents a comprehensive feasibility analysis of these concepts in the context of Nepal. The results of this research will provide valuable insights into the potential for adopting these innovative technologies in Nepal and will contribute to the development of a sustainable and efficient energy system.

Valorization of food and fruit wastes has the potential for the production of sustainable energy and biochemicals. Approximately 70% of the weight of the original jackfruit (Artocarpus heterophyllus L.) fruit is lost during processing as waste in the form of peeled skin and core, both of which have not been utilized and, thus contribute to disposal as well as pollution issues. The major components, cellulose, and hemicellulose, can be biologically transformed easily into bioenergy sources like ethanol, methanol, and butanol; valuable phenolics and biotechnological products like pectin, citric acid, bromelain, ferulic acid, and vanillin; and many other products. These residues can also be utilized as essential sources for the biological transformation process leading to the production of numerous products with added value, such as phenolic antioxidants, phenolic flavor compounds, and organic acids. Thus, the value addition of jackfruit waste can support the sustainable solution towards food and nutritional security. In this way, zero waste can be achieved through novel biorefineries which are critically highlighted in this paper. Furthermore, novel technologies for the conversion of jackfruit wastes are summarized with recent findings.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

Computer vision methods have shown to be effective in classifying garbage into recycling categories for waste processing, existing methods are costly, imprecise, and unclear. To tackle this issue, we introduce MWaste, a mobile application that uses computer vision and deep learning techniques to classify waste materials as trash, plastic, paper, metal, glass or cardboard. Its effectiveness was tested on various neural network architectures and real world images, achieving an average precision of 92% on the test set. This app can help combat climate change by enabling efficient waste processing and reducing the generation of greenhouse gases caused by incorrect waste disposal.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and &gt;115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

Vehicle routing is a critical factor in municipal solid waste (MSW) collection planning and operations. Poor routing can introduce inefficiencies and cause targeted levels of services or performance to be missed irrespective of the level of resource application. Trial and error approaches have been proven to be not the best in the planning and prediction of expected performance. This study explores various Geographic Information System (GIS) tools and analysis techniques, and how they can be applied to optimizing vehicle routes in light of challenging site conditions. Using Adentan West residential area, suburb of Accra Ghana as a case study, current performance of the trial and error method was measured and a GIS computer model was used to evaluate various optimization scenarios to determine the level of savings that can be made. Field measurements were taking with Global Positioning System (GPS) devices for waste collection activities in areas with varying characteristics and conditions, and data analysed for one selected vehicle operating four days per week. It was found that, for a scenario where only the bin collection order was optimized while route selection was restricted by the ArcGIS Network Analyst, 2.6% of travel distance and 2.21% of travel time were saved. For the second scenario where only the route selection was optimized while order of bin collection was restricted, 4.1% and 1.5% of travel distance and time respectively were saved. For a third scenario where both the order of collection and route selection were together optimized, 10.9% and 3.7% of travel distance and time respectively were saved. Lastly, by regrouping all the bins for daily collection, 4.5% and 1.2% of travel distance and time respectively were saved. The results demonstrated that there is always room for optimization of solid waste collection routing irrespective of site constraints and other challenges that the nature of bin distribution pose to drivers. In developing countries like Ghana, where there is high demand for services in the face of limited road network access, application of GIS in optimization of routes will guide providers in planning and subsequently make more savings in fuel consumption, vehicle maintenance and cost of man-hours.

One of the biggest problems that the Dominican Republic has had in recent decades is the efficient management of solid waste produced by the population. This problem has worsened in recent years due to the decrease in available areas for the construction of sanitary landfills, the lack of recycling culture in the population, the deficiency in waste collection, and the scarce legal controls aimed at preserving water and air and soil, among other factors. The objective of this study was to explore the management of solid waste by the population and the municipality of Puñal, province of Santiago, to evaluate and analyze the situation and generation of solid waste, municipal solid waste management services, and the attitudes of the population regarding recycling projects and waste management, to evaluate the viability and sustainability of the use organic waste for energy generation. A total of 275 households from 29 localities in the municipality of Puñal were surveyed, which allowed for a significant population sample. According to the results obtained, the most significant type of waste produced by families is organic waste, followed by plastic waste and paper. Of the total organic waste produced in the municipality, 53% of solid waste is disregarded through the municipal waste collection system, while 47% is used as plant fertilizers or animal feed. On the other hand, most households receive the municipal waste collection service and pay for this service. The results of our research show that the implementation of an energy production system based on organic waste would be viable in the municipality of Puñal. However, a more efficient waste collection system would be necessary and the development of programs and projects that allow all households to participate in the system.

The growing concern about climate change and the recognition of the planet’s limits led society to look for alternatives that promote the balance between the natural and the built environment. The circular economy emerges as an alternative to the linear economic model, inspired by natural metabolisms, by circulating resources in continuous loops, where their intrinsic value is maintained and improved. This research proposes a closed-loop strategy in the built environment by studying innovative constructive solutions that aim to find use, value, and inspiration in what is considered waste. A literature review is conducted on the circular design strategies, re-use and recycle typologies, and waste transformation processes. Then, the development of a methodology for qualitative evaluation and selection of re-used and upcycled construction materials from post-consumer waste and by-products is presented and then applied to thirty-five cases of constructive solutions from plastic, wood, paper, steel, aluminium, and agricultural waste. The research reports that the developed framework is adequate. The analysed alternative materials have good environmental performance and can be used as building materials despite their functional limitations, reflecting the enormous potential of waste as a resource for the construction industry.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

Millions of tons of wool waste are produced yearly by textile industries, which may become a serious environmental hazard in the near future. Given this concern, it is crucial to explore strategies to reduce the amount of wool waste generated worldwide and adopt more sustainable practices for dissolving and regenerating wool keratin (WK) from textile waste. Most traditional methods involve the use of expensive, toxic, harmful, and poorly biodegradable compounds. To overcome these limitations and facilitate the reuse of wool waste through a cascade valorization strategy, researchers have started testing the use of deep eutectic solvents (DES) as a more sus-tainable and eco-friendlier alternative for WK dissolution and regeneration. In this study, the potential of two different DES mixtures, Choline chloride (ChCl): Urea and L-Cysteine (L-Cys): Lactic acid (LA), was explored for dissolving wool waste. Subsequently, the obtained gels based on DES-WK were blended with polyvinyl alcohol (PVA) in different ratios to produce nanofibers using the electrospinning technique. The effect of pH and the properties of the electrospinning solutions, namely electrical conductivity and viscosity, on the morphology of the gel solutions were evaluated. Moreover, the morphological features of the produced gel-based electrospun PVA/DES-WK nanofibrous membranes were analyzed using scanning electron mi-croscopy (SEM). Additionally, the PVA/L-Cys: LA DES-WK, which proved to be the most effective DES mixture for fabricating WK gel-based nanofibers, were characterized through Fourier transform infrared spectroscopy (FTIR) and tensile tests. Furthermore, their antioxidant and an-timicrobial abilities were evaluated. The results obtained revealed that this approach to valorize textile waste offers a unique avenue for the development of sustainable functional materials with potential applications in various biomedical and industrial fields.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

Waste recovery is an important aspect towards human and environmental health protection. Unfortunately, proper food waste management is among the serious challenges in the field of solid waste management worldwide. Therefore, it is of great importance to conduct studies towards achieving efficient and cost-effective approaches for food waste management. This study investigated the potential of recovering food waste through maggots’ production as animal feed. The influence of fly attractant application on maggot production was also investigated. The study also investigated the potential of maggot production for waste recovery and reduction. Four different types of food waste (starch food leftovers, rotten bananas and peels, rotten pineapple and peels, and rotten oranges) were used in the investigation process. From the results, it was observed that the application of fly attractants had a significant effect on the production of maggots as determined by the weights after harvesting. Average weight of 94 g/kg of maggot was achieved from banana materials with an application of fly attractant during the 8th day of the cultivation; which is equivalent to a 32.4% increase from the same day when the material was cultured without applying fly attractant. Also, from the starch materials, about 77 g/kg of maggot weight was achieved; which is a 54.6% increase from the same day and the same material but without application of fly attractant. Moreover, the relative dry weight reduction in the trials varied from 52.5% to 82.4%.

The nationwide lockdown imposed to control the spread of novel coronavirus induced dramatic alterations in different sectors of the Nepalese governance, including Solid Waste Management (SWM) practices. The study identifies SW collection gaps in seven major cities of Nepal and highlights the municipal and public households on SW management practices before and during the lockdown to emphasize the linkage between COVID-19 and SWM. It includes information on solid waste status, collection frequency and coverage, workers safety practices, types of vehicles operated for collection and alternative methods adopted by households to manage SW during the lockdown. For this, 1329 households survey and key informant interviews were conducted in seven cities of Nepal during the lockdown. It was found that although the coverage of the collection service was similar during the pandemic, there was a drastic decrease in the collection frequency leading to a collection gap of around 570 tons/day. More than 50% of the surveyed households adopted no proper alternative measures as they claimed that they stored solid waste with proper management so that municipal authorities can take it. The study reveals poor occupational health and safety practices among the solid waste workers due to the unavailability of safety gears and equipment despite being aware of the modes of transmission of the virus. The pandemic exacerbated the challenges of smooth SWM as it is an essential and needy service. This study highlights the need for a timely strategic management framework to be developed by the government to continue the smooth SWM practices during the lockdown.

Objective: The aim of this study is to explore what inside the lipid lump obtained from skin. Try to understand the reasons for these physiological functions. In this paper, the lipid droplets or lumps was aimed to shed light on, figuring out what kind of cracks from metabolism were embedded inside. Results: A novel method was introduced for the detection of pathogens within lipid droplets extracted from acne or inflamed pores, as well as normal pores, using microscopic analysis. Through this technique, the presence of cracks from our body within these lipid droplets were identified. Methods: Observations were conducted using a microscope, with samples placed on slides and grind like blood smear. To enhance the transparency of the samples, tween-20 was utilized. This reagent was first time to be used for observing such big lipid lump of skin secretion. The evidences were recorded using the DMi8 camera from Leica.

Continuity of activities and projects are important for sustainably developing organizations, especially universities. The purpose of this research study is to find university development guidelines regarding waste management according to the green university ranking criteria for sustainable developments by studying and collecting the data covering the last five years (2019 - 2023) of Mahasarakham University. We also analyzed and synthesized lessons learned from the details of the operations and the factors involved in successes while comparing and providing suggestions for the operations in the next year. It was found that waste management that resulted in continuous developments that achieved the goals of Mahasarakham University consisted of the five guidelines. (1) Making green university policies and using them as the (key performance index) KPI of the divisions and also announcing the university's waste management policies by applying the principles of 3R (Reuse-Reduce-Recycle). (2) Allocating the budgets supporting the projects' activities according to the evaluation criteria. (3) Student and personnel participation as well as the mechanisms used by the committees from various administrative divisions such as Student Council, Student Association and clubs to drive the operations. (4) Identifying the main responsible individuals and committees for the green university who communicated and drove the operations while collecting, analyzing and preparing the data. (5) Follow-ups and evaluations of the project's activities with the Plan-Do-Check-Act (PDCA) processes for continuous and sustainable developments and improvements leading to the green university. With the above operations, Mahasarakham University's waste management scores of the six indices during 2019 - 3023 increased annually as follows: 900, 900, 1050, 1275 and 1350.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

Natural fibers have attracted increasing interest as an alternative to produce environmentally friendly and sustainable materials. Particularly, hemp fibers have revealed to be widely used in various industrial applications due to their extremely unique properties. However, hemp can generate a large amount of agro-waste, and results in an attractive source of biopolymers for the development of low-cost materials in alternative to the raw materials and conventional petroleum-based plastics. In addition, deep eutectic solvents (DESs), a new type of truly green solvents, have been tested to remove gums, lignin, and other non-cellulosic components from hemp fibers. Reusing these components dissolved into the DESs to fabricate new materials directly by electrospinning is a very attractive but still unexplored endeavor. Thus, this innovative research to venture new upcycling pathways is focused on the fabrication of composite nanofibers by electrospinning of a gel-based blend of Poly(vinyl alcohol) (PVA) and hemp agro-waste (HW) dissolved into choline chloride (ChCl) : Glycerol (1:2) and ChCl : Urea (1:2) DES mixtures. The results obtained revealed that the produced nanofibers displayed uniform appearance with diameters ranging from 257.72 ± 65.63 nm to 380.78 ± 133.98 nm. In addition, the mechanical properties of the electro-spun composite nanofibers produced from the gel-based blends of HW dissolved in DESs and PVA (HW-DESs_PVA) were found to be superior, resulting in an enhanced tensile strength and Young’s modulus. Furthermore, the incorporation of HW into the nanofibers was able to provide bioactive antioxidant and antibacterial properties. Overall, this study demonstrated a promising, more sustainable, and eco-friendly way to produce electrospun composite nanofibers using HW in a circular economy perspective.

A shrimp oil rich in omega-3 lipids and carotenoids is obtained in remarkably high 5 wt% yield extending to pink shrimp processing waste (head and carapace) the circular economy approach to extract fish oil from fish processing by-products using d-limonene. Biobased limonene, a powerful antimicrobial and antioxidant agent, is an excellent solvent for both lipids and astaxanthin-based carotenoids preventing oxidative degradation during the extraction cycle including solvent and oil separation at 85°C. A new low cost route is established to extract valued marine oil from biowaste annually made available in over 2.2 million tonnes.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Nano-emulsions of essential oils (EO) and their chemical constituents are promising raw materials for the ecological control of Tribolium castaneum. Curcuma longa Linn is a plant known for the properties of its rhizome which is used in food, health and hygiene products. Its leaves are by-products with no commercial value, but with unexplored bioactive volatile constituents. This study aims to evaluate the repellency of nano-emulsions containing the EO from leaves of C. longa or its three main chemical constituents against T. castaneum. The representative mixture of EO extracted in four different months showed p-cymene (26.0%), 1,8-cineole (15.1%) and terpinolene (15.5%) as major compounds. Nano-emulsions of EO (HLB 16.7), terpinolene (HLB 15.0), 1,8-cineole (HLB15.0) and p-cymene (HLB 15.0) were repellent at concentrations of 11 μg/cm2 (EO, terpinolene and p-cymene) and 1.1 μg/cm2 (1,8-cineole). The EO nano-emulsion droplet size increased linearly over time, remaining below 300 nm for 35 days and below 600 nm for 80 days. The EO nano-emulsion proved to be a green alternative to synthetic pesticides, as it was safe against the bioindicator Chlorella vulgaris. Terpinolene, 1,8-cineol and p-cymene were able to inhibit the enzyme telomerase from T. castaneum in an in silico assay, which may explain the repellency of these samples. This study provides ideas for the utilization of EO from leaves of C. longa as raw material of new environmentally friendly plant-derived nanobiopesticides.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

In municipal waterworks large amounts of waste in the form of sludge have to be discarded. This investigation focuses on the processing of ceramic floor tiles incorporated with a municipal waterworks sludge. Four floor tile formulations containing up to 10 wt. % of the municipal waterworks sludge in replacement of kaolin were prepared. The floor tile processing route consisted of dry powder granulation, uniaxial pressing, and firing between 1190 and 1250 °C using a fast-firing cycle (<60 min). The densification behavior and technological properties of the floor tile pieces as function of the sludge addition and firing temperature were determined. The development of the microstructure was followed by XRD and SEM/EDS. The results show that the replacement of kaolin with municipal waterworks sludge, in the range up to 10 wt. %, allows the production of ceramic floor tiles (group BIb and group BIIa, ISO 13006 Standard) at lower firing temperatures. These results suggest a new possibility for valorization of municipal waterworks sludge with many economical and environmental benefits.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

Peat is the main type of peloid used in Polish cosmetic/healing spa facilities. Depending on treatment and origin, peat waste can be contaminated microbiologically, and as result, it has to be incinerated in medical waste incineration plants without energy recovery (local law). Such a situation leads to peat waste management costs increase. Therefore in this work, we checked the possibility of peat waste upcycling to carbonized solid fuel (CSF) using torrefaction. Torrefaction is a thermal treatment process that removes microbiological contamination and improves the fuel properties of peat waste. In work torrefaction conditions (temperature and time) on CSF quality were tested. Parallelly, peat decomposition kinetics using TGA, and torrefaction kinetics with lifetime prediction using macro-TGA were determined. Furthermore, torrefaction theoretical mass and energy balance were determined. The results of the tested peat were compared with reference material (wood), and as result, obtained data can be used to adjust currently used wood torrefaction technologies for peat torrefaction. The results show that torrefaction can improve the high heating value of peat waste from 19.0 MJ x kg-1 to 21.3 MJ x kg-1, peat main decomposition takes place at 200-550 °C following second reaction order (n=2), with an activation energy of 33.34 kJ x mol-1 and pre-exponential factor of 4.40 x 10-1 s-1. Moreover, DSC analysis revealed that peat torrefaction required slightly more energy than wood torrefaction, and macro TGA showed that peat torrefaction has lower torrefaction constant reaction rates (k) than wood 1.05 x 10-5 - 3.15 x 10-5 vs 1.43 x 10-5 - 7.25 x 10-5 s-1.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

Acerola (Malpighia spp.) is a tropical plant genus of shrubs and trees whose fruit is rich in nutrients and bioactive compounds. However, its production generates significant waste that could pose an environmental issue. This review aims to summarize recent research on the potential uses of acerola wastes, including the extraction of bioactive compounds such as polyphenols, carotenoids, and pectins, as well as the development of materials such as nanomaterials, chitosan, and biofuels. Additionally, the paper discusses the potential medical applications of acerola wastes, such as wound healing, antioxidant, and anticancer effects. Finally, the paper explores the challenges and opportunities of using acerola waste as a sustainable source of raw materials and energy. The findings suggest that acerola waste could be a valuable resource for developing high-value products and promoting sustainable production practices in the fruit industry.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

The basic principles of geological risk calculation through Probability of Success (PoS) are mostly applied for numerical estimation of additional hydrocarbon existence in proven reservoirs or potential hydrocarbon discoveries in selected geological regional subsurface volume. It can be tailored and validated for a comprehensive input dataset collected in the selected petroleum province, adapted by dividing up geological events into several probability categories and classes. The most applied categories are (existence of) reservoir rocks, traps and isolators, source rocks, migration pathways and preservation conditions for hydrocarbons The methodology results in unique probability values as multiplication of independent statistical events, which can also be applied in the assessment of a potential hydrocarbon discovery of desired minimal volume and its value in any virtual currency like risk-neutral dollars. Such methodology has been extensively developed in the last decades in the Croatian subsurface, mostly in the Croatian part of the Pannonian Basin System (CPBS). Through the adaptation of geological categories, it was also applied in hybrid, i.e., stochastical, models developed in the CPBS (Drava Depression). Stochastically estimation of porosity was already applied. As the robustness of this methodology is very high, it was also modified to estimate the influence of water-flooding in increasing oil recovery in some proven Neogene sandstone reservoirs in the CPBS (Sava Depression). This new modification is being presented to be applied to geological risk calculation, intending to assess the safety of geological environment in deep wells, where depleted radioactive fuel would be disposed, a subject of great importance. The case study encompassed the magmatic and metamorphic rocks in the pre-Neogene basement of the CPBS. For disposal purpose, these are regionally lithologies considered as to be the safest ones considering petrophysical values, water saturation, recent weathering and tectonic activity.

The volume of electronic waste (e-waste) received in Nigeria is reportedly on the increase and the effects on environmental health are yet to be fully ascertained. This study aimed to investigate haematological indices, lead and serum iron levels in workers occupationally exposed to electronic wastes in South-South, Nigeria. In this pilot study, 104 participants were enrolled from Benin City, South-South Nigeria; consisting of 63 E-waste Workers (EW) sex- and aged-matched with 41 Unexposed Participants (Control). Blood levels (5 mL) of the metals (lead and iron) were determined using Inductively Coupled Plasma-Mass Spectrometry while the haematological parameters [white blood cells (WBC), Lymphocytes ( LY); monocytes (MO), granulocytes(GR), red blood cells (RBC), haemoglobin (Hgb), haematocrit (HCT), mean cell volume (MCV), mean cell haemoglobin (MCH), mean cell haemoglobin concentration (MCHC) and platelets (PLT)] were determined using standard methods. Results obtained from this study show a significantly low serum iron (11.5 ± 2.14 µg/dL) in the EW compared with Control (168.9 ± 2.39 µg/dL); while blood lead level in EW (1.07±0.02 µg/dL) was significantly elevated compared with Control (0.72 ± 0.12). Total WBC and RBC, HCT, MO and MCV were all significantly elevated in EW compared with Control while LY and PLT in the EW were significantly decreased compared with Control. This study concludes that chronic occupational e-waste exposure may increase blood lead level, lower serum iron status and may have adversely altered some important haematological parameters in the studied population.

Sustainable bio-economy is considered to be one of the most promising routes towards the transition to a circular and climate-neutral economy. The valorization industry of bio-waste and agri-food by-products represents a key player in bioeconomy. In this article the design and the development of a web platform aiming at promoting synergies enabling the agricultural waste valorization is presented. The platform consists of: (i) the AgriPLaCE Waste Management Database which provides the users with an extended list of potential utilization measures for a variety of agricultural waste streams (ii) the AgriPLaCE Synergies Tool which aims to create synergies between different actors involved in the value chain from agricultural waste production to waste treatment and new valuable products’ exploitation. At the initial stage, the conceptual design of both tools took place by conducting an in-depth analysis for the user needs and services alongside the system architecture. Following, the AgriPLaCE platform development stage took place, with the implementation of all the necessary subsystems. The results showed that multiple potential collaborations can arise by the use of the AgriPLaCE platform, while users can also deepen on alternative and emerging treatment technologies and valuable products that can derive from a wide range of agricultural waste streams.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

Effective solid waste management is crucial for protecting public health and the environment. Global concentration on finding sustainable methods of handling waste continue to top the list of most governmental-related project checklists. This paper provides a case study on the management of municipal solid waste in the cities of Karlsruhe, Germany and Navrongo, Ghana as developed and developing countries respectively. This study aimed at comparing and drawing lessons from how these two different cities manage their solid waste. The waste management system in Karlsruhe prioritizes waste separation, recycling, and a pay-as-you-throw system has led to an efficient and sustainable waste management system that minimizes waste and protects the environment. Karlshrue's adoption of a continual developmental plan structure focused on integrated WM concepts is credited with safeguarding the long-term viability of waste management in the city. In contrast, Navrongo's waste management system faces several challenges, including inadequate resources and infrastructure, traditional waste disposal practices, and the lack of well-planned waste management strategies. To improve effective solid waste management systems in Ghana, a collaborative approach involving the government, local organizations, and the community is necessary. This can include investing in infrastructure, implementing waste separation and recycling programs, and educating the public on the benefits of sustainable waste management practices. Learning from successful models like Karlsruhe can help accelerate the development of sustainable waste management practices in Ghana, and ultimately protect public health and the environment.

Solid waste has become a tenacious issue worldwide. It has been increasing exponentially due to urbanization and the increase in the population. Since the twentieth-century technological revolution, there have been significant changes in the composition of solid waste. It poses significant challenges for waste management systems worldwide. Waste management is the process of handling waste right from its creation to its final disposal, including transport, collection, treatment, and monitoring. The present solid waste management (SWM) system is affected by unfavorable institutional, economic, technical, legislative, and operational constraints. Poor waste management is affecting ecosystems and human health, damaging our finite natural resources, impeding human economic progress, and harming people's quality of life. Now, researchers are concerned about the environment's degradation, a decline in quality of life, and risks related to waste management grow as the volume of solid waste. So, they are focusing on sustainable waste management practices which will be crucial for creating a cleaner and healthier environment for future generations. This chapter focuses on the concept of solid waste, its types, management, and its effect on the health of humans and the environment.

It is expected that due to the new UE regulation focus on waste management, managing kitchen waste will become more important in the future, especially in households. It is, therefore, crucial to develop user-friendly and odor-free containers to store kitchen waste. The study aimed to test the effectiveness of compost biochar in reducing noxious odors and volatile organic compounds (VOCs) released during kitchen waste storage. Varying quantities of compost biochar (0%, 1%, 5%, and 10%) were added to food waste samples and incubated for seven days at 20℃. VOCs released were analyzed on days 1, 3, and 7 of the storage simulation process. The results indicated that adding 5-10% of composts’ biochar to kitchen waste significantly reduced emissions in 70% of detected VOCs compounds. Additionally, Compost's biochar can be used to eliminate potential odor components and specific dangerous VOCs such as ethylbenzene, o-xylene, acetic acid, and naphthalene. A new composts’ biochar with a unique composition was particularly effective in reducing VOCs and could be an excellent solution for eliminating odors in kitchen waste con-tainers.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

In recent years, Malaysia has faced environmental challenges caused by municipal solid waste, especially household waste, during the Covid-19 pandemic. Among all the household waste, plastic and paper are the most prominent waste that causes environmental hazards. Several recycling associations in Malaysia have carried out their practices for better waste sustainability and management to curb the increasing amount of household waste. However, the effectiveness is still vague in achieving smart and effective household waste management. Therefore, this paper aims to investigate Malaysia’s household waste management, mainly in three significant municipalities in Malaysia for Kuala Lumpur, Penang and Melaka, in becoming a resilient and sustainable city by addressing two main research questions 1) What are the key factors for ensuring the more success move for future household waste management in cities? and 2) How will the 3 municipalities address their waste issues based on the key factors from RQ1, respectively? This paper reviewed 13 waste management articles and explores the potential of the four factors of waste management from the perspective of technology and data, economy, social and governance. The discussed factors and models contributed to an integrated future-proofing framework that focuses on smart waste tracking, an gamified awareness education, and strict policies to control waste management are the way forward for the future of smart cities household waste management.

Agricultural product like cassava produces huge amounts of waste when processed to consumable goods. The waste generated is generally considered to contribute largely to environmental pollution. This study therefore investigates the waste management practice that is adopted by cassava processors in Ogun State, Nigeria. Five (5) Local Government Areas (LGAs) dominant in processing cassava were selected for the study on the basis of spatial location distribution; landmass and population. The survey involved the use of structured questionnaires administered to cassava processors of the selected LGAs. The Statistical Package for Social Sciences (SPSS) software application and descriptive statistics were used for data analysis. Results of the analysis show that majority (70%) of the cassava processors are females. Cassava peel constitutes 10% of the waste produced, of which 91% are heaped at refuse dump in most communities. Results also reveal that 86.3% of cassava residues are used for animal feeds. Other findings show that the peels when dried are used as bio-fuel for cooking and there is a significant potential for biogas production. From the data captured from respondent during the study, most processors are willing to pay for an improved waste management system. The study therefore suggests proper waste management of cassava waste to minimize environmental pollution.

Target 12.3 of the United Nations Sustainable Development Goals (SDGs) calls for halving per capita global food waste at the retail and consumer levels, by 2030. The Food Waste Index is suggested as a methodology for grasping the situation. This paper focuses on the consumer level (household food waste). We argue that in order for generating useful information for devising and implementing effective measures for reducing food waste, it should be measured at Level 3 of the Food Waste Index, based on sorting analysis of generated waste, making a distinction between avoidable and non-avoidable food waste. Furthermore, a breakdown by sub-categories that reflect the flow of food in the household could help identify target behaviours. We have developed a categorisation scheme that is internationally agreeable and adoptable, and 1) generates useful information for policy-making and for tackling with reduction of food waste, 2) makes clear the concept of avoidable food waste, and 3) is practical and does not overcomplicate the work of grasping the situation of food wastage. Results of workshops regarding this scheme suggest that the scheme satisfies the criteria. This scheme has been applied to a few sorting analyses of household food waste in Japan, and their results are compared.

The interest in high homogenization pressure technology has grown over the years. It is a green technology with low energy consumption, not generating high CO2 emissions or polluting effluents. The main food applications derive from its effect on particle size, causing a more homogeneous distribution of fluid elements (particles, globules, droplets, aggregates, etc.) and favouring the release of intracellular components; and its effect on the structure and configuration of chemical components such as polyphenols and macromolecules such as carbohydrates (fibres) and proteins (also microorganisms and enzymes). The challenges of the 21st century lead food industry processing towards obtaining food with high nutritional quality and taking advantage of waste to obtain ingredients with specific properties. For this purpose, soft and non-thermal technologies such as high pressures homogenization have a huge potential. The objective of this work is to review how the need to combine safety, functionality and sustainability in food industry has conditioned the last decade applications of high-pressure homogenization technology.

Despite good intentions, the increasing number of plastic bag bans aimed at alleviating marine plastic pollution saw a correlated increase in the number of unintended consequences that emerged alongside the bans, suggesting that human behavior towards plastic bag consumption have not changed, but merely shifted, and are feeding into other major international environmental catastrophes. Nudge theory, which helps people make better choices for themselves without inhibiting their free will, is a potential solution that has been shown to play a subtle but important role in providing options under circumstances where complex information needs to be streamlined for the wider community, avoiding any unintended consequences and behavioural shifts that might arise from instruments that diminishes autonomy. It is therefore timely to look into the insights of nudge theory to encourage a positive behavioural change to reduce plastic bag consumption. Here we apply a systematic literature review to show how successful applications of nudges in supermarkets can be leveraged to reduce plastic bag consumption. We find that the current applications of nudges in various industries worldwide, including supermarkets have produced positive and encouraging results, as well as producing lasting behavioural change among the wider community. Supermarkets are identified as a powerful deployment site of these nudges due to their positioning as a dominant provider of plastic bags to the wider community, as well as being the largest and leading provider of daily food needs. Finally, we synthesise our findings to produce a coherent and testable framework of actionable interventions that supermarkets can employ to nudge customers towards reduced plastic bag reliance, accompanied with a visual timeline of a customer shopping in a supermarket experiencing these nudges.

Fish oil rich in polyunsaturated omega-3 fatty acids is extracted in high yield from anchovy filleting waste using d-limonene as green biosolvent in a simple solid-liquid extraction performed by mechanically stirring and maceration followed by limonene removal via evaporation under reduced pressure. As limonene is renewably obtained from waste orange peel, this protocol establishes a circular bioeconomy method to obtain valued omega-3 extracts from biowaste available worldwide in several million t/year amount. The method closes the materials cycle and opens the route to full valorisation of an important biological resource so far mostly discarded as waste. Significant economic opportunities benefiting local communities, the ecosystem and public health are anticipated.

This paper examines the relationship between GDP per capita and waste generated in European Union countries, highlighting the importance of this relationship for understanding the environmental consequences of economic growth and formulating waste management policies. The analysis findings demonstrate that, in most cases, higher GDP is associated with higher amounts of waste, although there are exceptions to this trend. A smaller number of countries are also found where no such relationship exists. These are primarily high-income countries in the lower part of the EKC or countries in transition. Cluster analysis reveals regional differences in the relationship between GDP and waste that the economic factors and the level of development in the regions concerned can explain. Bulgaria is among the European countries with the lowest economic growth associated with a large amount of waste. The analysis, therefore, focuses on Bulgaria. The impact of GDP per capita, Human Development Index and Population Density on municipal waste in Bulgaria is studied. The aim is to identify significant relationships and dependencies between these factors and the amount of waste. Based on the results of multiple regression analysis and the findings from municipal waste management data in Bulgaria, specific actions are proposed for municipal waste management in the country. Recommendations are made for developing sustainable waste management policies and sharing best practices between regions.

Recycling and waste management have garnered immense popularity in recent years, but few studies have been carried out regarding these systems. Therefore, an in-depth literature review was done in order to highlight the different sectors of the recycling system that need to be reformed. Hence this study examined recycling and waste management systems within three categories–medical, municipal, and plastic–that were carried out pre and post COVID by reviewing previous studies, technical reports, and annual reports. This was done by visiting numerous academic search engines alongside online resources that were utilized to assemble literature related to waste and recycling systems. Continuing a recurring idea was that no matter the type of waste, further research regarding all waste should be carried out. Additionally, since recycling and waste management are a vital part of our society, and seeing how unpredictable events such as the pandemic may be, it is paramount that that research is done not only on how the pandemic has affected systems now, but also how we can learn from current issues to utilize them for future “waste shocks”.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Indonesia's government anticipates waste problems by managing them through a large number of waste reduction programs. From a governance perspective in Indonesia, it is known that actors from diverse governmental levels and across sectors are involved in waste management, and their involvement largely depends on their institutional goals and problems. Hence, they are expected to coherently collaborate together by developing and implementing sustainable instruments and resources for improving waste management problems. However, it is necessary to understand how supportive and restrictive the governance of waste reduction programs is to encourage successful trash reduction. This study is designed to evaluate and examine the application of Community-Based Solid Waste Management (CBSWM) in Makassar. In this research, The Governance Assessment Tool (GAT) was applied to analyze the governance context of the waste reduction programs in Makassar qualitatively. From the assessment, contexts can be described as either supportive or restrictive of the processes of implementing public policies on waste management. As a result of such an assessment, this study shed light on some opportunities to improve the governance of waste management implementation's impact on reducing waste in Makassar, South Sulawesi, Indonesia. The conclusion of this study depicts that the most important actors are affiliated with the local government and the community. Moreover, this study shows that the assessment of contextual governance is predominantly restrictive.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

A renewable cyclic monoterpene obtained from citrus peel, limonene is widely used as a fra-grance, nutraceutical ingredient, antibacterial, biopesticide, and green extraction solvent. Indus-trial demand largely exceeds supply. After reviewing recent advances in the recovery of limonene from citrus peel and residues with a particular attention to benign-by-design extractive processes, we focus on the latest results in its dehydrogenation to p-cymene via heterogeneous catalysis.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

Liability to prevent consequences of an unhealthy situation due to accumulating toxic and hazardous emissions caused by open dumping of municipal solid waste with increasing urbanization has necessitated a renewed thinking on waste disposal. Grate fired incineration systems were adopted by urban managements in past and present but with criticisms due to formation of air borne emissions. Improved combustion methods like fluidized bed are now propagated because of current requirements like efficient energy recovery potential, stricter emission norms, adaptability with urban growth, adaptability to co-firing with other waste like biomass, edible oil wastes or industrial effluent and integration with conventional energy generation. Such a comprehensive and futuristic approach is more sustainable for the community. Multi-criteria decision-making tool is used to identify the best technology option among grate combustion and fluidized bed combustion for disposing and energy recovery from waste. Ten different collection and disposal options involving two combustion methods, namely, grate combustion and fluidized bed method are considered. Utilization of the energy is done for three end uses, namely, power generation, water distillation and district cooling. Two different regions in Saudi Arabia are considered for this study under two types of scenario, namely with recycling and without recycling. The different options are prioritized based on their overall ranking using five major performance factors.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

Municipal landfills play a vital role in disposing of the solid waste from a community. One of the biggest challenges landfill management face is when the available storage space is being reduced faster than the rate that was planned for. This shortening of the landfill lifecycle impacted the city of Wilmington, Delaware when it was found that their landfill had lost 11 years of its projected lifespan and would reach fully capacity within the next decade. In order to remedy the situation six alternative solutions were devised, with each having different costs (capital, operating, and transport) and varying lengths of landfill extension. This research used the principle of optimization via a LINDO program to determine which solution would achieve the longest landfill extension for the minimum total cost. Other constraints placed on the program include reducing the waste being sent to the landfill and to achieve a minimum of 25 additional years for the landfill. The calculated solution produced a cost reduction of $232.64 million dollars and 3.2 additional years of operation from the option that was eventually chosen by the landfill authority.

In the past years, consumers have increased their interest to buy healthier food products, rejecting those products with more additives and giving preference to the fresh ones. Moreover, the current environmental situation has made society more aware of the importance of reducing the production of plastic and food waste. In this way and considering the Food Industry need of reducing the food spoilage along the food chain, edible coating has been considered as an eco-friendly food packaging that can replace traditional plastic packaging providing an improvement in the product’s shelf-life. Edible coating are thin layers applied straightaway on the food materials’ surface, that are made of biopolymers that usually incorporate other elements, such as nanoparticles or essential oils, to improve their physicochemical properties. These materials must provide a barrier that can prevent the pass of water vapor and other gasses, the microbial growth, the moisture loss, and the oxidation, so the shelf-life could be extended. The aim of this review was to compile the current data available to give a global vision of the formulation process and the different ways to improve the characteristics of the coats applied in both fruits and vegetables. In this way, the suitability of compounds in by-products produced during the Food Industry chain were also considered for the edible coating production.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

Food waste is one of the greatest challenge to sustainability in developed and developing countries. In the former, food waste is concentrated in the final part of the chain. Too Good To Go is a digital platform aimed to prevent food waste, where consumers can buy magic boxes from different outlets containing food products that are approaching their end-of-life. However, the mechanism of the platform enable the outlets to publish their offering much in advance of the pick-up time, raising the question whether the food sold on the platform is effectively a leftover or a planned production. Our empirical study gathers data from over 1200 outlets in Rome on the Too Good To Go platform.

Genetic adaptation of Hermetia illucens (BSF) to suboptimal single sourced wastes can open new perspectives for insect production. Here, four replicate BSF lines were maintained on a single sourced, low-quality wheat bran diet (WB) or on a high-quality chicken feed diet (CF) for 13 generations. We continuously evaluated evolutionary responses in several performance traits to rearing at the two diets. Subsequently, we tested responses to interchanged diets, i.e. of larvae that had been adapted to low-quality feed and to high quality feed and vice versa to evaluate costs associated with diet adaptation. BSF were found to experience rapid adaptation to the diet composition. While performances on WB diet were always inferior to CF diet, the adaptive re-sponses were stronger to the former diet. This stronger response was likely due to stronger se-lection pressure experienced by BSF fed on the low-quality single sourced diet. The interchanged diet experiment found no costs associated with diet adaptation but confirmed diet adaptation for the larval biomass and insect frass traits for the WB diet treatment. Our results revealed that BSF can rapidly adapt to diet through evolutionary responses, which has potential to be utilized to produce lines tailored to specific diets.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The purpose of this study is to assess the solid waste management status and practice in Sendafa town, Oromia regional state residents. In order to achieve this goal, the researcher intends to employ both primary and secondary data from the Sendafa town municipality. With the aid of multi-cluster sampling and a purposive sampling method, the researchers chose a sample size of 398 people and 10 interview responders. To utilize a systematic sampling technique at intervals of residences, individual samples were chosen. Quantitative data was cleaned and analysed using STATA software. A multiple linear regression model and logistic regression other descriptive statistics methods were then used to change the results. The qualitative data were imported, coded, and thematised using ATLAS.ti.9 in order to prepare respondents' interviews for analysis. The findings indicate that residents' poor solid waste management practices are a result of a lack of awareness, low family income transportation issues, issues with waste collectors, a lack of a sense of responsibility and belonging, and a failure to enforce current solid waste management laws. Solid waste accumulates near roads, bridges, and residential areas that are close to landfills, contaminating the area and leading to diseases like TB and Asthma (and other related health issues in children and adults who live there). Thus, researcher recommends that to have sustainable solid waste management the town administrators should have plan to develop awareness creation symposium or panel of discussion, resolve transportation issues, monitor and guide the routine activities of waste collectors, develop sense of belongingness for themselves and for the community, develop integrated solid waste land fill projects and working with all stakeholders like NGO and health institution will minimize the adverse effect of improper solid waste management. Keywords: Solid Waste, Status of Solid Waste Management, Land fill site suitability

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

Cigarette butts (CBs) are the most diffuse waste in the world, often abandoned in the environment without proper disposal. They are dangerous because of the numerous harmful chemicals poten-tially released in the environment. There are, in literature, several technological options for CB recycling, but some critical concerns could affect their effectiveness due to the quality and quantity of CB litter collected in the proper way. The present paper focuses on policy framework social behavior, waste collection and transport and technological processes. The Extended Producer Responsibility scheme for CBs is proposed at European level as an action to tackle CB litter and encourage sustainable product development. The CB waste collection and transport is a key step for bringing CB to the recycling process. The main concern is the small quantity of CBs collected: 0.06 % of the municipal waste and 0.18 % of the unsorted waste in the administrative area of Pe-rugia. Another crucial issue is the need for behavioral interventions to increase education and awareness of smoker citizens, addressing the discrepancy between smokers’ behaviors and beliefs.

Fruits are commonly used, fresh or processed, to prepare different industrial products with superior nutritional and health-promoting properties. Currently, the demand for processed fruit products has motivated the rapid growth of the fruit processing industries, persuading them to produce an enormous amount of by-products with less utilization. Furthermore, people's shifting dietary habits and lack of awareness of nutritional properties result in an avoidable load of fruit by-products. The knowledge of the value of by-products urges exploration with proper documentation, emphasizing the health benefits of some such products. Hence, this review is prepared by carefully analyzing the recent literature on industrial applications of fruit by-products and their nutritional and health-promoting properties. The use of fruit by-products in food industries for various purposes has been reported in the past and has been reviewed and described here. Fruit by-products are a good source of nutrients and bioactive components, including polyphenols, dietary fibers, and vitamins, implying that they could have an important role for novel, value-added functional food properties. Furthermore, fruit by-products are used as the substrate for the production of organic acids, essential oils, enzymes, fuel, biodegradable packaging materials, and preservatives.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

Recent years have experienced an increase in construction and demolition waste (C&amp;DW), which is the most significant solid waste stream. C&amp;DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&amp;DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&amp;DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&amp;DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&amp;DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&amp;DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

The possibility of making precious stones from radioactive waste is being considered. Vitrified and cemented radioactive waste (RW) is considered as an artificial rock belonging to aluminosilicates and calcites. Two methods are proposed for the manufacture of radioactive gemstones from RW and their subsequent storage with the possibility of sale, resale, inheritance, and so on. That is, RW is considered as real estate in which capital can be invested. After decontamination in hundreds and thousands of years, it will be of scientific, historical, jewelry interest.

The new climate law introduces a policy of sustainable construction, the assumption of which is the reduction of CO2 by the construction industry and the use of environmentally friendly materials, such as agricultural, mineral, and recycled waste, while limiting the consumption of natural resources. The article is a literature review that analyzes selected waste materials from various sectors of the economy that can be used as additives or partial substitutes for natural resources in the production of cement and in and cement building materials, the production of which reduces CO2 emissions, producing materials with high mechanical strength and environmentally friendly.

An adequate number of waste management facilities is the key element to meet circular economy goals. Using empirical data taken from official sources the research framework bases on an econometric model to compare the elasticity of cost on quantity of different alternatives such as waste-to-energy facilities, mechanical biological facilities and landfills impact on waste management cost. Results suggest that both waste-to-energy facilities (-0.278%) and landfills (-0.38%) concur to lower the cost while the higher the percentage of waste sent to mechanical biological treatment facilities, the higher the cost (0.788%). This figure deserves to be examined in more details as such facilities represent an intermediary step in the chain which efficiency depends on the industrial organization of the chain.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

Extensive use of petrochemical plastic packaging leads to the greenhouse gas emission and con-tamination to soil and oceans, posing major threats to the ecosystem. The packaging needs, hence, are shifting to bioplastics with natural biodegradability. Lignocellulose, the biomass from forest and agriculture, can produce cellulose nanofibrils (CNF), a biodegradable material with ac-ceptable functional properties, that can make packaging among other products. CNF extracted from lignocellulosic wastes can lower the packaging carbon footprint and the production cost. Most of these low value feedstocks go to alternative applications, that make their use in CNF packaging competitive. To transfer the waste materials from current practices to the packaging production, it is imperative to assess their sustainability, encompassing environmental and eco-nomic impacts along with the feedstock physical and chemical properties. A consolidated over-view of these criteria is absent in the literature. This study performs an iterative literature review and presents thirteen attributes, delineating sustainability of lignocellulosic wastes for commer-cial CNF packaging production. These criteria data are gathered for the UK waste streams, and transformed into a quantitative matrix, evaluating the waste feedstock sustainability for CNF packaging production. The presented approach can be adopted to decision scenarios in bioplas-tics packaging conversion and waste management.

Human and animal waste, including waste products originating from human or animal digestive systems such as urine, feces, and animal manure, have constituted a nuisance to the environment. Inappropriate disposal and poor sanitation of human and animal waste often cause negative impacts on human health through contamination of the terrestrial environment, soil, and water bodies. Therefore, it is necessary to convert these wastes into useful resources to mitigate their adverse environmental effect. The present study provides an overview and research progress of different thermochemical and biological conversion pathways for the transformation of human- and animal-derived waste into valuable resources. The physicochemical properties of human and animal waste are meticulously discussed as well as nutrient recovery strategies. In addition, a bibliometric analysis is provided to identify the trends in research and knowledge gaps. The results reveal that the U.S.A, China and England are the dominant countries in the research areas related to resource recovery from human or animal waste. In addition, researchers from the University of Illinois, the University of California Davis, the Chinese Academy of Science and Zhejiang University are front runners in research related to these areas. Future research should be centred on developing technologies for the on-site recovery of resources, exploring integrated resource recovery pathways, and exploring different safe waste processing methods.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

In road construction, before applying an asphalt or concrete surface, the ground must be compacted and stabilized. There are two basic methods of soil stabilization: in situ and in a stationary node (ex-situ). The method of performing stabilization in place (in-situ) is the most frequently used method due to its convenience and lower price. The most popular type of binder for stabilization is a hydraulic binder (most often cement and various ashes). Such stabilization is performed at a depth of 10-50 cm, achieving the desired load-bearing parameters. In order to improve them, various chemical additives for stabilization are often used, such as ion exchange compounds, additives based on sulfuric acid, additives based on vinyl polymers or even organic additives using lignosulfonates. However, the use of such additives is associated with much greater costs and environmental burden, resulting in seeking for cheaper and equally effective alternatives. The win-win situation would be for instance recycling the problematic waste-based materials that on one hand are landfilled or impossible to recycle and on the other hand cause problems for the waste producers. Therefore, an interesting issue is the production of stabilization additives from various types of waste materials. As a result of the extensive testing of various waste-based materials blends with soil, the mechanical (compressive strength after 7 and 28 days) and hydraulic (capillary rise, water absorption, frost resistance) soil properties were measured. The optimization process led to obtaining additives compositions ensuring the best strengthening and sealing properties. These were for sandy soil: Pure foil (wax emulsion), Pure foil (wax emulsion) + waste sulphuric acid, RDF from waste tires (wax emulsion), Pure foil (wax emulsion) + “by-pass” waste ash + NaOHx2 and for clayey soil: Pure foil (wax emulsion) + NaOH, Pure foil (wax emulsion) + waste sulphuric acid, Tequant, Pure foil (wax emulsion).

The use of food waste disposers in gastronomical facilities influence the municipal wastewater composition. Ground food waste poses problems in the operation of the sewerage network and generates high electric energy consumption in wastewater treatment plants (WWTP). The study aimed to determine, for five towns with a PE of 4,000 to 220,000, the volumes of catering waste discharged to the WWTPs. The towns differed in the number of inhabitants, beds in hotel and catering places. The calculations were made based on data received from the operators of WWTP. The pollutant concentrations in 2019, were compared with data from the "pandemic" year - 2020. The loads of catering waste entering the sewerage system in 2019 ranged from 32.7 to 1062 tons. In town with the largest tourist base, the BOD value in 2020 accounted for 62.3% of 2019 value. In the largest town, the annual energy consumption for food waste treatment could be up to 2,539,770 kWh. If the waste was fermented, it could be obtained up to 1,376,650 m3 of methane. There is a strong need for implementing a collection system for food waste from catering facilities and its fermentation to produce methane, which can be used for energy purposes.