Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

Vehicle-to-Vehicle (V2V) communication plays a pivotal role in modern intelligent transportation systems, enabling seamless information exchange among vehicles to enhance road safety, traffic efficiency, and overall driving experience. However, the secure transmission of sensitive data between vehicles remains a critical concern due to potential security threats and vulnerabilities. This research paper focuses on investigating the security protocols employed in Vehicle-to-Vehicle communication systems. A comprehensive review and analysis of relevant literature and research papers is conducted to gather information on existing V2V communication security protocols and techniques. The analysis encompasses key areas, including authentication mechanisms, encryption algorithms, key management protocols, and intrusion detection systems specifically applicable to V2V communication networks. Within the context of real-world V2V environments, this study delves into the challenges and limitations associated with implementing these protocols. Moreover, to foster a deeper understanding, the paper investigates present communication protocols in the field of Internet of Things (IoT) that are tailored for V2V. Various parameters, such as band-width consumption, energy consumption, latency, and message size, are considered during the evaluation of these protocols to gauge their effectiveness. The research outcomes aim to provide a comprehensive understanding of the strengths and weaknesses of the current V2V communication security protocols. Furthermore, based on the findings, this paper will propose improvements and recommendations to enhance the security measures of the V2V communication protocol. Ultimately, this research will contribute to the development of more secure and reliable V2V communication systems, propelling the advancement of intelligent transportation technology.

The current study investigated the use of two-dimensional spatial distribution mapping representing the chlorophyll-a level in a river generated via an unmanned aerial vehicle (UAV) and an unmanned surface vehicle (USV). A domestically developed UAV (Remo-M, Uconsystem Inc., Korea) and a USV developed by our research team were used to collect data from the Nae Seong stream in Korea. An adaptation of the “Data Cleaner” tool was developed and used for USV data processing and analysis. The operation of the autonomous USV was successful. Four previously described indices for quantifying algal blooms in rivers were utilized to create chlorophyll-a images, the normalized difference vegetation index (NDVI), the normalized green red difference index, the green normalized difference vegetation index (GNDVI), and the normalized difference red edge index. The suitability of the linear regression analysis of the correlation between the spectral indices obtained using the UAV and the in situ chlorophyll-a data obtained using the USV was evaluated with the coefficient of determination (R2) at a significance level of p &lt; 0.001. In field application and correlational analysis the NDVI was strongly correlated with chlorophyll-a (R2 = 0.88, p < 0.001), and the GNDVI was moderately correlated with chlorophyll-a (R2 = 0.74, p < 0.001). The map of chlorophyll-a was successfully quantified using the UAV and USV hybrid platforms.

As V2X technology develops, acute problems related to reliable and secure information exchange between network objects in real time appear. The article aims to solve the scientific problem of building a network architecture for reliable delivery of correct and uncompromised data within the V2X concept to improve the safety of road users, using blockchain technology and mobile edge computing (MEC). The authors present a formalized mathematical model of the system, taking into account the interconnection of objects and V2X information channels, and an energy-efficient algorithm of traffic offloading to the MEC server. The paper presents the results of application of blockchain technologies and mobile edge computing in the developed system, their description, evaluation of advantages and disadvantages of the implementation.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

In this paper, we present a novel Two-Echelon Ground Vehicle and Its Mounted Unmanned Aerial Vehicle Cooperated Routing Problem (2E-GUCRP). The 2E-GUCRP arises in the field of Unmanned Aerial Vehicle (UAV) Routing Problem such as those encountered in the context of city logistics. In a typical cooperated system, the UAV is launched from the Ground Vehicle (GV) and automatically flies to the designated target. Meanwhile, acting as a mobile base station, the GV can charge or change the UAV’s battery on the designated landing points to enable the UAV to continue its mission. The objective is to design efficient GV and UAV routes to minimize the total mission time while meeting the operational constraints. A Mixed Integer Programming (MIP) model, which could be solved by commercial software, is constructed to describe this problem. In order to quickly solve the medium-scale problems, two existing heuristics to solve 2E-VRP are improved. The computational experiments are set up to compare our model with the 2E-VRP. The results indicate that the 2E-GUCRP obtains a better efficiency. Further discussion of the practical instance points out that the increase in efficiency is related to the speed relationship between the GV and the UAV.

The number of people owning vehicles has been steadily growing, resulting in increased numbers of vehicles on the roads, making roads more congested, and increasing the risk of accidents. In addition, heavy rain, snow, and fog have increased due to abnormal weather caused by global warming. These bad weather conditions can also affect the safety of vehicles and drivers. The need to disseminate safety messages on the social internet of vehicles due to these problems has been steadily increasing. In this paper, we propose an efficient safety message dissemination scheme that focuses on urban environments with high vehicle density and mobility to address these problems. The proposed scheme reduces packet loss by considering frequent cluster departures and subscriptions through an efficient cluster management technique. In a vehicle-to-vehicle environment, the dissemination of safety messages is divided into an intra-cluster and an inter-cluster emergency as well as general safety message dissemination technique. In a vehicle to infrastructure environment, the proposed scheme reduces the number of processing requests and duplicate messages made to roadside units (RSUs) through a request operation process for each vehicle and an RSU scheduling technique. We conducted several performance evaluations of message packet loss and the number of RSU processing requests to demonstrate the superiority of the proposed scheme.

Since the 1990’s, studies and pilot tests have been conducted to reduce traffic, accidents, and pollution due to urban freight transport (UFT). These ended up in several policies, regulations, and restrictions for UFT, such as low emission zones, delivery time windows, and vehicle size and weight restrictions. However, issues in UFT under regulatory measures still persevere. This study introduces an optimization framework for deriving an optimal combination of various types of vehicles with different capacities for vehicle replacement in UFT. This framework allows an understanding of how an urban freight company with a limited budget efficiently satisfies its freight demand within an urban area in the presence of regulatory measures by urban administrators. The introduced formulation, which is a mixed-integer linear programming, will assist the operator in choosing the best investment strategy for introducing new vehicles of certain types and sizes, for operation in different zones, into its fleet while gaining economic benefits and having a positive impact on the liveability of the urban area. Furthermore, a sensitivity analysis is performed to consider the effects of specific uncertain parameters on the total cost. The numerical results show that the share of electric vehicles in the fleet increases, and they are more competitive than diesel vehicles.

Over the past decade, wireless communication technologies have developed significantly for intelligent applications in road transport. This paper provides an overview of telecommunications-based intelligent transport systems with a focus on ensuring system safety and resilience. In vehicle-to-everything, these problems are extremely acute due to the specifics of the operation of transport networks, which requires the use of special protection mechanisms. In this regard, it was decided to use blockchain as a system platform to support the needs of transport systems for secure information exchange. This paper describes the technological aspects of implementing blockchain technology in vehicle-to-network; the features of such technology are presented, as well as the features of their interaction.

Wind loads have become one of the key influence factors for the running safety of vehicles and comfort of passengers. Investigation on the wind speed spectrum characteristics of a moving vehicle under turbulent crosswinds is of great influence. Expressions of the wind speed spectrum of a moving vehicle was obtained from the von Kármán spectrum based on Taylor’s frozen flow hypothesis. The influence factors, including the ratio of the vehicle speed to the wind speed and the wind yaw angle from 15° to 175°, were analyzed. The maximum value of the wind speed spectrum and the corresponding frequency were studied as well. The results show that the maximum values of the wind speed spectrum of the moving vehicle were larger than those of the static vehicle. The maximum value of the wind speed spectrum corresponding to the moving vehicle first increased and then decreased as the wind yaw angle increased. Some of the frequencies corresponding to the longitudinal wind speed spectrum values of the moving vehicles were smaller than those of the static vehicle. For moving vehicles, the frequency values corresponding to the maximum values of the longitudinal wind speed spectrum first increased and then decreased as the ratio of the vehicle speed to the wind speed and the wind yaw angle increased.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (&lt;5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

Pedestrians, bicyclists, scooterists are Vulnerable Road Users (VRU) in traffic accidents. The number of fatalities and injuries in traffic accidents involving vulnerable road users has been steadily increasing in the last two decades in the U.S. even though road vehicles now have perception sensors like camera to detect risk and issue collision warnings or apply emergency braking. Perception sensors like camera are highly affected by lighting and weather conditions. Camera, radar and lidar cannot detect vulnerable road users in partially occluded and occluded situations. This paper proposes the use of Vehicle-to-VRU communication to inform nearby vehicles of VRUs having trajectories with potential collision risk. An Android smartphone app with low energy Bluetooth (BLE) advertising is developed and used for this communication. The same app is also used to collect motion data of VRUs for training. VRU motion data is smoothed using a Kalman filter and an LSTM neural network is used for future motion prediction. This information is used in an algorithm comparing Time-To-collision-Zone (TTZ) for the vehicle and VRU and issue a driver warning with different severity levels. The warning severity level is based on analysis of real data from a smart intersection for close vehicle and VRU interactions. The resulting driver warning system is demonstrated using proof-of-concept experiments. The method can easily be extended to a VRU collision mitigation system.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

The widespread adoption of electromobility constitutes one of the measures designed to reduce air pollution caused by traditional fossil fuels. However, several factors are currently impending this process, ranging from insufficient charging infrastructure, battery capacity, long queueing and charging time, to psychological factors. On top of range anxiety, the frustration of the EV drivers is further fueled by the lack the uncertainty of finding an available charging point on their route. To address this issue, we propose a solution that comes to bypass the limitations of the Reserve now function of the OCPP standard, enabling drivers to make charging reservations for the upcoming days, especially when planning a longer trip. We created an algorithm that generates reservation intervals based on the charging station's reservation and transaction history. Subsequently, we ran a series of test cases that yielded promising results, with no overlapping reservations.

Nowadays, people like to travel to alleviate the stress and depression in their busy lives, and if they can do so at a low cost, it will be even more beneficial to them. The usual way for a traveler to book a ticket or to contact a travel agency is to book a ticket. It becomes more expensive for travelers. Due to the lack of vehicle management, travel agencies don’t get their appropriate profit. In this journal, we have provided proficient solutions for vehicle optimization to minimize travel costs. However, when travelers want to travel, they don’t find a proper tour guide, and it is sometimes expensive to arrange a proper tour guide. Moreover, travelers often don’t find a suitable package, and occasionally they do not know the place where they may want to visit. In this paper, we have discussed how we used effective methods to reduce vehicle costs for tour purposes. Further, we have developed a solution where bus seats are optimally occupied, and the package system and tour guide are included in it. We have also added a blog portal to our web-based software to introduce all tourist places and their information. In this journal, the proposed optimal vehicle usage system has been developed using Hypertext Markup Language (HTML), Cascading Style Sheets (CSS), the Tailwind Framework, React, and Node.js.

The need for continuous research to refine the models used in accident reconstruction appears with the development of new car models that satisfy consumer complaints. The paper analyzed a sub-sequence of car and pedestrian accidents, from the perspective of the distance traveled by them in the contact phase, with the aim of improving the information regarding the reconstruction of road accidents. The research included the analysis of some accidents with pedestrian dummies, as well as the simulation of the impact between different classes of vehicles and pedestrians in two different walking positions. Specialized software was used with complex multibody models of pedestrians, modifying the speed and deceleration parameters at the time of the collision. The research results highlight the differences between bilinear models used in accident reconstruction and the proposed study. They can also be used to determine the distance traveled by the vehicle in the first phase of the collision with pedestrians.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

The development of autonomous vehicles is becoming increasingly popular and gathering real world data is considered a valuable task. Many datasets have been published recently in the autonomous vehicle sector, with synthetic datasets gaining particular interest due to availability and cost. For a real implementation and correct evaluation of vehicles at higher levels of autonomy it is also necessary to consider human interaction, which is precisely something that lacks in existing datasets. In this article the UPCT dataset is presented, a public dataset containing high quality, multimodal data obtained using state of the art sensors and equipment installed onboard the UPCT’s CICar autonomous vehicle. The dataset includes data from a variety of perception sensors including 3D LiDAR, cameras, IMU, GPS, encoders, as well as driver biometric data and driver behaviour questionnaires. In addition to the dataset, the software developed for data synchronisation and processing has been made available. The quality of the dataset was validated using an end-to-end neural network model with multiple inputs to obtain speed and steering wheel angle and obtained very promising results.

The environmental safety of a car is currently one of the most important indicators of the vehicle competitiveness and quality in the consumer market. Currently, the assessment of the ecological properties of vehicles can be made based on various criteria. In the case of combustion-powered cars, the most attention is usually paid to the values characterizing their use, and in the environmental assessment, first of all to pollutant emissions and operational fuel consumption. The proposed article considers the possibility of using the life cycle assessment to analyze the ecological properties of a passenger car during its operation. A simplified LCA method of the vehicle was presented, which in strictly defined cases can be used for the analysis of environmental impacts and the assessment of the energy analysis related to its operation. For this purpose, a vehicle life cycle model was developed. Data on the operation of 33 passenger cars of different manufacturers with similar operational characteristics, coming from different production periods, were analyzed in detail. The obtained results were found to be highly sensitive to the assumptions made in the article.

Carsharing has become increasingly popular in recent years as a sustainable transportation solution, offering individuals access to shared vehicles on a short-term basis. One-way carsharing, in particular, presents unique challenges due to its flexible nature, allowing users to pick up and drop off vehicles at different locations within a designated service area. This flexibility increases the service ridership but comes at the expense of vehicle imbalance among the stations, as some stations may have excess vehicles while other stations have vehicle shortages. Therefore, carsharing companies need to decide on strategies to ensure a balanced distribution of vehicles among the stations. This is essential as unbalanced vehicle distribution can lead to the unavailability of vehicles when needed or, conversely, result in an increased number of unnecessary rebalancing trips, thereby exacerbating traffic congestion and environmental pollution. Such issues can potentially undermine the overall contribution of carsharing to urban sustainability. To this end, this paper reviews the vehicle imbalance problem that arises in this field and the solution algorithms that solve them.

UAVNs (unmanned aerial vehicle networks) may become vulnerable to threats and attacks due to their characteristic features such as high mobility, highly dynamic network topology, and open-air wireless environments. Since previous work has focused on classical and metaheuristic-based approaches, none of these approaches have a self-adaptive approach. In this article, we examine the challenges of cyber detection methods to secure UAVNs and review exiting security schemes proposed in the current literature. Furthermore, we propose an agent-based self-protective method (ASP-UAVN) for UAVNs that is based on the Human Immune System (HIS). In ASP-UAS, the safest route from the source UAV to the destination UAV is chosen according to a self-protective system. In this method, a multi-agent system using an Artificial Immune System (AIS) is employed to detect the attacking UAV and choose the safest route. In the proposed ASP-UAVN, the route request packet (RREQ) is initially transmitted from the source UAV to the destination UAV to detect the existing routes. Then, once the route reply packet (RREP) is received, a self-protective method using agents and the knowledge base is employed to choose the safest route and detect the attacking UAVs. The method is evaluated here via extensive simulations carried out in the NS-3 environment. The experimental results of four scenarios demonstrated that the ASP-UAS increases the Packet Delivery Rate (PDR) by more than 17.4, 20.8, and 25.91%, and detection rate by more than 17.2, 23.1, and 29.3%, and decreases the Packet Loss Rate (PLR) by more than 14.4, 16.8, and 20.21%, the false-positive and false-negative rate by more than 16.5, 25.3, and 31.21% those of SUAS-HIS, SFA and BRUIDS methods, respectively.

Recently, the use of drones/unmanned aerial vehicles (UAVs) has notably increased due to their broad commercial spread and low cost. The wide diffusion of drones increases the hazards of their misuse in illegitimate actions such as drug smuggling and terrorism. Thus, the surveillance and automated detection of drones are crucial for safeguarding restricted regions or special zones from illegal drone interventions. One of the most challenging issues in drone detection in surveillance videos is the apparent similarity of drones and birds against complex backgrounds. In this work, an automated image-based drone-detection system utilizing an advanced deep-learning-based object-detection method known as you only look once (YOLOv5) is introduced for protecting restricted regions or special zones from unlawful drone interventions. Due to the lack of sufficient data, transfer learning was utilized to pretrain the object-detection method to increase the performance. The experiments showed outstanding results, and an average precision of 94.7% was accomplished.

Vehicle identification is an important task in traffic monitoring because it allows for efficient inference and provides a cause for action. Vehicle classification via deep learning and other approaches such as segmentation is a critical tool for re-identification. In this paper, instance segmentation is used to identify vehicle makes with license plate detection, allowing for better unique vehicle recognition for re-identification. A dataset is annotated and modified, for example, by segmenting it with polygonal bounding boxes that capture the vehicle's unique frontal features. In addition, license plate localization is performed. The results showed improved classification as well as a high mAP for the dataset when compared to previous approaches based on CNN and deformed CNN. Furthermore, a deep residual network and fully connected layer-based classification were utilized as the backbone for feature representation. Instance segmentation detects objects by segmenting and classifying regions of interest. The imbalance in the dataset is resolved using a mosaic-tiled approach, which produces greater precision than other approaches.

In the last decades, technological advances related to RNA manipulation enabled and expanded its application in vaccine development. This approach comprises synthetic single-stranded mRNA molecules that direct the translation of the antigen responsible for activating the desired immune response. The success of RNA vaccines depends on the delivery vehicle employed. Among the systems, yeasts emerge as a new approach to a natural delivery platform. The presence of β-glucans and mannans in its wall is responsible for the adjuvant action of this system. Yeasts are already employed to deliver protein antigens, with success and efficacy demonstrated through pre-clinical and clinical trials. Yeast β-glucan capsules, microparticles, and nanoparticles are capable of modulating host immune responses and have a high capacity to carry RNA and small molecules, with bioavailability upon oral immunization and with targeting to receptors present in anti-gen-presenting cells (APCs). Besides, yeasts are interesting vehicles for the protection and specific delivery of therapeutic vaccines based on shRNA or dsRNA. In this review, we present an overview of the attributes of yeast or its derivatives for the delivery of RNA-based vaccines, discussing their current challenges and prospects for using this promising strategy.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Satellites are subject to various severe vibration during different phases of flight. The concept of satellite smart adapter is proposed in this study to achieve active vibration control of launch vehicle on satellite. The satellite smart adapter has 18 active struts in which the middle section of each strut is made of piezoelectric stack actuator. Comprehensive conceptual design of the satellite smart adapter is presented to indicate the design parameters, requirements and philosophy applied which are based on the reliability and durability criterions to ensure successful functionality of the proposed system. The coupled electromechanical virtual work equation for the piezoelectric stack actuator in each active strut is drived by applying D'Alembert's principle. Modal analysis is performed to characterize the inherent properties of the smart adapter and extraction of a mathematical model of the system. Active vibration control analysis was conducted using fuzzy logic control with triangular membership functions and acceleration feedback. The control results conclude that the proposed satellite smart adapter configuration which benefits from piezoelectric stack actuator as elements of its 18 active struts has high strength and shows excellent robustness and effectiveness in vibration suppression of launch vehicle on satellite.

The dependence on Unmanned Aerial Vehicles (UAVs) has dramatically increased in many sectors around the globe. UAVs are in high demand, and their technology is developing quickly due to their sophisticated ability to handle various issues. UAVs are capable of replacing labor-intensive tasks with conducive and safe regulation. Additional tools or sensors need to be added to the UAVs system to ensure the implementation of UAVs able to serve into industrial level. The paper aims to consolidate and present a thorough understanding of the various stages of image processing pipelines deployed in UAV applications, including image acquisition, preprocessing, feature extraction, object detection and tracking, and decision-making processes. Throughout this paper, several aspects were deliberate such as strengths, limitations, and performance metrics of existing approaches, this paper seeks to provide researchers, engineers, and practitioners with valuable insights into the challenges and opportunities of image processing systems for UAVs. Ultimately, the synthesis of this knowledge will contribute to enhancing the effective-ness, autonomy, and applicability of UAVs in diverse fields such as surveillance, agriculture, disaster management, and environmental monitoring.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

This paper develops a two-layer optimization approach that provides energy-optimal control for vehicles and traffic signal controllers. The optimizer in the first layer computes the traffic signal timings to minimize the total energy consumption levels of approaching vehicles from upstream traffic. The traffic signal optimization can be easily implemented in real-time signal controllers, and it overcomes the issues in the traditional Webster’s method of overestimating the cycle length when the traffic volume-to-capacity ratio exceeds 50 percent. The second layer optimizer is the vehicle speed controller, which calculates the optimal vehicle brake and throttle levels to minimize the energy consumption of individual vehicles. The A-star dynamic programming is used to solve the formulated optimization problem in the second layer to expedite the computation speed so that the optimal vehicle trajectories can be computed in real-time and can be easily implemented in simulation software for testing. The proposed integrated controller is first tested on an isolated signalized intersection, and then an arterial network with multiple intersections to investigate the performance of the proposed controller under various traffic demand levels. The test results demonstrate that the proposed integrated controller can greatly improve energy efficiency with fuel savings up to 17.7%, at the same time enhancing traffic mobility by up to 47.18% reduction in traffic delay and up to 24.84% reduction in vehicle stops.

Recently, inter-vehicle communication, which helps to avoid collision accidents (by driving safety support system) and facilitate self-driving (by dissemination of road and traffic information), has attracted much attention. In this paper, in order to efficiently collect road / traffic information in the request / response manner, first a basic method, Content-centric network (CCN) for Vehicular network (CV), is proposed, which applies CCN cache function to inter-vehicle communication. Content naming and routing, which take vehicle mobility into account, are investigated. On this basis, the CV method is extended (named as ECV) to avoid the cache miss problem caused by vehicle movement, and is further enhanced (named as ECV+) to more efficiently exploit cache buffer in vehicles, caching content according to a probability decided by channel usage rate. Extensive evaluations on network simulator Scenargie, with realistic open street map, confirm that the CV method and its extensions (ECV, ECV+) effectively reduce the average number of hops of data packets (by up to 47%, 63%, 83% respectively) and greatly improve the content acquisition success rate (by up to 356%, 444%, 689%, respectively), compared to the method without cache mechanism.

Aiming at the problem of hypersonic morphing vehicle avoiding no-fly zones and reaching the target, an improved predictor-corrector guidance method is proposed. Firstly, the aircraft motion model and the constraint model are established. Then, the basic algorithm is given, the Q-learning method is used to design the attack angle and sweep angle scheme to ensure that the aircraft can fly over the low-altitude zones. The B-spline curve is used to design the location of flight path points and the bank angle scheme is designed according to the predictor-corrector method, so that the aircraft can fly around to avoid high-altitude zones. Next, Monte Carlo reinforcement learning(MCRL) method is used to improve predictor-corrector method and Deep Neural Network(DNN) is used to fit reward function. The improved method can generate trajectory with better performance. Simulation results verify the effectiveness of the proposed algorithm.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

The key to ensuring the sustainability of transportation operations on the roads is to manage traffic flows homogeneously. By homogenizing the behavior of various drivers, traffic operation can be optimized, and traffic safety can be improved. However, the advent of autonomous vehicles is expected to have a major impact on the homogeneity of sustainable transportation operations. In this study, a method of driving in harmony with surrounding vehicles was studied to minimize the impact of autonomous vehicles on current traffic operation. In particular, in this study, a methodology was developed to optimize the driving behavior of autonomous vehicles by analyzing the driving behavior of following vehicles using spectrum analysis. Specifically, a method for calculating three indicators that can analyze the driving behavior of a following vehicle, such as reaction time, stimulus adaptation index, and collision risk avoidance index, was proposed. These indices produced consistent and robust results for all traffic conditions. If these indicators are used, it is expected that sustainable traffic management will be possible even when autonomous vehicles and human drivers are mixed on the road.

Navigation is the most challenging issue in autonomous vehicles. Researchers in the current era have developed many Artificial Intelligence techniques to navigate, generate paths, and avoid obstacles for optimum path planning for autonomous vehicles. Different studies have investigated bio-inspired techniques to overcome the navigation issue, including obstacle avoidance. This paper uses new meta-heuristic optimization techniques called Dragonfly Algorithm (DA) to set the goal by detecting and avoiding obstacles with minimum human interference. For effective results, the Dragonfly-Fuzzy hybrid algorithm is analyzed over the unstructured environment because individual techniques may not be sure of an optimal solution over all configurations. The main advantage of the proposed hybrid controller is that it combines the multiple features of different approaches into a single controller. This paper compares simulation and experimental findings over various environmental conditions to the individual algorithm. Regarding time and path optimization, the hybrid Dragonfly-Fuzzy controller performs better than the respective controller.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

The use of logistic regression models in data analysis and machine learning has expanded in recent years and has become the primary preference of researchers in risk assessment studies across a wide range of scientific fields. From the assessment of credit risk in financial institutions to the estimation of risk factors for traffic accidents or the identification of etiological factors for chronic diseases. All logistic models are natural extensions of the simple binary model, and their interpretation is based on it. Using the data of a cross-sectional study on the risk factors of traffic collisions, the two main extended models of logistic techniques, multinomial and ordinal logistic regression, are presented in the article in detail. Emphasis is placed on the use of ordinal regression since the outcome variable of the collision data is defined as ordinal measurement reflecting a latent continuous scale.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

This paper proposes an electric vehicle routing problem with considering states of charging stations and suggests solution strategies. Charging of electric vehicles is a main issue in the field of electric vehicle routing problem. There are many studies to find locations of charging stations, recharging functions for batteries of vehicles, and so on. However, states of charging stations significantly affect the routes of electric vehicles, which is not much explored. The states may include open or close of charging stations, occupied or empty of charging slots, and so on. This paper investigates how the states of charging stations are estimated and routing strategies are determined. We formulate a mixed integer programming model and suggest how to solve the problem with exact method. Numerical examples provide the optimal routing strategies of electric vehicles in the changing environments of the states of charging stations.

This work targets the development of a mobility control system for high-speed series hybrid electric tracked vehicles, which operate with independent traction motors for each track. The scope of the research encompasses the modeling of the series hybrid powertrain specific to military tracked vehicles, as well as an in-depth analysis of their dynamic behavior. Subsequently, the study conducts a critical review of the mobility control approaches sourced from literature, identifying key techniques relevant to high-inertia vehicular applications. Building on the foundational models, the study puts forward a robust closed-loop mobility control system aimed at ensuring precise and stable off-road vehicle operations. The system's resilience and adaptability to a variety of driving conditions are emphasized, with a particular focus on handling maneuvers such as steering and pivoting, which are challenging operations for tracked vehicle agility. The performance of the proposed mobility control system is tested through a series of simulations, covering a spectrum of operational scenarios. These tests are carried out in both offline simulation settings, which permit meticulous fine-tuning of system parameters, and real-time environments that replicate actual field conditions. The simulation results demonstrate the system's capacity to improve vehicular response and highlight its potential impact on the future designs of mobility control systems for the heavy-duty vehicle sector, particularly in defense applications.

This paper presents a study on the idle vibration reduction of a diesel sport utility vehicle (SUV). To reduce idle vibration, the transmission paths of vibration from the engine to the driver seat floor were investigated with the vehicle components related to idle vibration. Furthermore, operational deflection shape (ODS) tests were conducted to visualize the vibration shapes during engine idling. Experimental modal analyses were performed to obtain the natural frequencies and mode shapes. Through the ODS and modal tests, the vibration characteristics of the diesel SUV during idling were identified. Considering these vibration characteristics, a multi-body dynamic model for the diesel SUV described by differential equations of motion was established to evaluate the idle vibration. To implement the dynamic model effectively, the equivalent stiffnesses and damping coefficients included in the model were determined experimentally or analytically. The established dynamic model was verified by comparing the natural frequencies and idle vibration levels between simulations. Using this dynamic model, we analyzed the effects of various design variables on idle vibration and obtained an optimal design for reducing the idle vibration level. Finally, we present a design guide to reduce the idle vibration for diesel SUVs.

This study focuses on the recently emerged Internet of Vehicles (IoV) concept to provide an integrated agricultural vehicle/machinery tracking system through two leading low power wide area network (LPWAN) technologies, namely LoRa and NB-IoT. The main aim is to investigate the theoretical coverage limits by considering the urban, suburban, and rural environments. Two vehicle tracking units (VTUs) have been designed for LoRa and NB-IoT connectivity technologies that can be used as reference hardware in coverage analysis. On this basis, the closed-form explicit analytical expressions of the maximum transmission range have been derived using the Hata path loss model. Besides, the computer simulation results have been validated via the maps from XIRIO online radio planning tool. In light of the obtained findings, several evaluations have been made to enhance the LPWAN-based agricultural vehicle tracking feasibility in smart farms.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

In this study, we focused on the eco-driving of electric vehicles (EVs). The target vehicle is an electric bus developed by our research team. Using the parameters of the bus and speed pattern optimization algorithm, we derived the EV eco-driving speed pattern. Compared to eco-driving of internal combustion engine vehicles (ICVs), we found several different characteristics. We verified these characteristics with actual vehicle driving test data of the target bus, and the results confirmed its rationality. The EV eco-driving method can improve electricity consumption by about 10% - 20% under the same average speed.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

Personal Mobility Vehicle (PMV) which has an inward tilting angle turns with the lateral force due to large camber angle, so it is necessary to consider the lateral movement of the tire vertical load axis during turning. Although the steering torque mechanism are very different from those of automobiles, there are not many examples which studied the steering torque mechanism of PMV. In this paper, based on the effects of six components force acting on the tires, a method for setting the steering axis specifications is derived, including the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. Although, automobile tires have a significant ground camber angle when traveling on rutted roads, they do not have it on slant roads because the vehicle body tilts along the road surface. On the other hand, in PMV, the vehicle body always keeps upright when traveling both on slanted roads and on rutted roads. Therefore, the tires have ground camber angles on both types of road surface. We study the straight running ability under such road surface disturbances based on the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. This straight running ability can be a remarkable strong point of PMV with an inward tilt mechanism.

The unsupervised domain-adaptive vehicle reidentification approach aims to transfer knowledge from a labeled source domain to an unlabeled target domain, however there are knowledge differences between the target domain and the source domain. To reduce domain differences, existing unsupervised domain-adaptive rerecognition methods generally require access to the source domain data to assist in re-training the target domain model. But for security reasons, in many cases, data between different domains cannot communicate. To this end, this paper proposes an unsupervised domain-adaptive vehicle re-identification method based on source-free knowledge transfer. First, by constructing a passive domain knowledge migration module, the target domain is consistent with the source domain model output to train a generator to generate the "source-like samples". Then, it can effectively reduce the model knowledge difference and improve the model generalization performance. According to the experiment and testing of VeRi776 and VehicleID, two mainstream public data sets in this field, the rank-k and mAP indexes obtained are both improved, and are suitable for object re-recognition tasks without source data.

This study presents a dynamic model of a passenger vehicle and analyzes its dynamic characteristics and responses. A dynamic vehicle model with seven degrees of freedom was established to analyze the behavior of a driving vehicle. The vehicle model had three degrees of freedom for the motion of the sprung mass and four degrees of freedom for the unsprung masses. For this model, the equations of motion were derived using Lagrange’s equation. To verify the model, the suspension deformations computed using the model were compared with the deformations measured through three actual vehicle driving tests which are the slalom, double lane change, and step steer tests. Furthermore, we investigated the effects of suspension stiffness, suspension damping, and anti-roll bar torsional stiffness on the dynamic characteristics and responses of the vehicle model. The developed dynamic vehicle model may help vehicle designers predict the dynamic responses of a vehicle through simulation without performing a driving test.

In this contribution, different lane-keeping control strategies for Autonomous Ground Vehicles (AGV) have been analyzed and compared. The AGV must be oriented and kept within a given reference path using the front wheel steering angle as the control action for a specific longitudinal velocity. While non-linear models can describe the lateral dynamics of the vehicle in an accurate manner, they might lead to difficulties when computing some real-time control laws such as Model Predictive Control (MPC). Linear Parameter Varying (LPV) models can provide a trade-off between computational complexity and model accuracy. Another way to reduce computational complexity is to explore other control strategies, for example, the one based on the Inverse Kinematic Bicycle model (IKIBI). Additionally, AGV sensors typically work at different measurement acquisition frequencies so that Kalman Filters (KF) are usually needed for sensor fusion. If these frequencies are slower than the actuation rate, a multi-rate KF may be needed. The two control strategies (MPC using a LPV model and IKIBI) have been compared in simulations over a circuit path in the presence of process and measurement Gaussian noise. The MPC controller has shown to provide a more accurate lane-keeping behavior than an IKIBI control strategy. Finally, it has been seen that Dual-Rate Extended Kalman Filters (DREKF) constitute an essential tool when only slow and noisy sensor feedback is available in an AGV lane-keeping application.

With the great development of intelligent transportation systems (ITS), travel time prediction has attracted the attentions of many researchers and a large number of prediction methods have been developed. However, as an unavoidable topic, the predictability of travel time series is the basic premise for travel time prediction has received less attention than the methodology. Based on the analysis of the complexity of travel time series, this paper defines travel time predictability to express the probability of correct travel time prediction and proposes an entropy-based method to measure the upper bound of travel time predictability. Multiscale entropy is employed to quantify the complexity of travel time series, and the relationships between entropy and the upper bound of travel time predictability are presented. Empirical studies are made with vehicle trajectory data in an express road section. The effectiveness of time scales, tolerance, and series length to entropy and travel time predictability are analysis, and some valuable suggestions about the accuracy of travel time predictability are discussed. Finally, the comparisons between travel time predictability and actual prediction results from two prediction models, ARIMA and BPNN, are conducted. Experimental results demonstrate the validity and reliability of the proposed travel time predictability.

The problems of operating range and costs are the two most critical bottlenecks restricting the extensive application of electric vehicles at home and abroad. There are also some prominent problems in China's electric vehicles, such as slow improvement of electric vehicle's operating range, difficulty in charging, slow charging, low utilization efficiency of charging resources, and high battery cost for electric vehicles, which lead to poor competitiveness of electric vehicles compared with traditional internal combustion engine (I.C.E.) vehicles. This paper analyzes the key factors restricting the development and popularization of electric vehicles in China from the aspects of strategic policy, sales situation and self problems. Through summarizing the experience and lessons of French standardization development strategy and electric vehicle development mode, this paper puts forward the hypothesis leading the development of electric vehicles through standardization to enhance their competitiveness, gives the specific suggestions, and briefly analyzes the feasibility from the aspects of product situation. The research content of this paper provides a certain basis and ideas for the future research work.

The performance analysis of the internal/external flows around a high speed vehicle in near-space is fundamental and critical to the configuration and structure design for high speed aircraft. In this paper, the two-dimensional coupled implicit Reynolds Average Navier-Stokes (RANS) solver and RNG k–ε turbulence model is employed to numerically simulate the flow field of an integrated high speed vehicle. The flow field are divided three parts to solve separately and compared with that solved by integrated simulation. The flow field are decomposed to save computer storage and simulation time. The first part is inlet/isolator, the second part is combustion chamber and the third is nozzle. In the computation process, the outlet condition of isolator is endowed to the inlet boundary of combustion chamber and the outlet boundary of combustion chamber is endowed to the inlet boundary of nozzle, then the whole flow field of integrated high speed vehicle is solved. Aerodynamic characteristic of fragment-computation and integration-computation is comparatively analyzed at different angles of attack, the results show that the maximum deviation of lift coefficient obtained by fragment-computation is less than 3% compared with that by integration, the maximum deviation of drag coefficient fragment-computation is less than 5% compared with that by integration, while pitching moment coefficient deviation less than 12%. However, for simulation time-consumption, the time used by fragment-computation reduces 45% compared with integration-computation. Meanwhile, by components force analysis, it can be concluded that the aerodynamic property of inlet/isolator can been obtained separately and hardly effected by other parts.

Unmanned aerial vehicle (UAV) usage is increasing drastically worldwide as UAVs are used in various industries for many applications, such as inspection, logistics, agriculture, and many more. This is because performing a task using UAV makes the job more efficient and reduces the workload needed. However, for a UAV to be operated manually or autonomously, the UAV must be equipped with proper safety features. An anti-collision system is one of the most crucial and fundamental safety features that UAVs must be equipped with. The anti-collision system allows the UAV to maintain a safe distance from any obstacles. The anti-collision technologies are of crucial relevance to assure the survival and safety of UAVs. Anti-collision of UAVs can be varied in the aspect of the use of sensors and the system’s working principle. This article provides a comprehensive overview of anti-collision technologies for UAVs. It also presents drone safety laws and regulations that prevent a collision at the policy level. The process of anti-collision technologies is studied from three aspects: Obstacle detection, collision prediction, and collision avoidance. A detailed overview and comparison of the methods of each element and an analysis of their advantages and disadvantages have been provided. In addition, the future trends of UAV anti-collision technologies from the viewpoint of fast obstacle detection and wireless networking are presented.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

This work focuses on addressing the dynamic positioning and trajectory tracking problem for a 4 degree-of-freedom (DOF) unmanned underwater vehicle (UUV) in the presence of nonlinear dynamics, parametric uncertainties, system constraints, and time-varying external disturbances. To tackle this problem, a disturbance observer-based control (DOBC) scheme is proposed. The scheme is structured around the model predictive control (MPC) method integrated with an extended active observer (EAOB). Compared to the conventional disturbance observer, the EAOB has the unique ability to handle both external disturbances and system/measurement noises simultaneously. The EAOB leverages a combination of sensor measurements and a system dynamic model to estimate disturbances in real-time, which allows continuous estimation and compensation of time-varying disturbances back to the controller. The proposed disturbance observer-based MPC (DOBMPC) is implemented by feeding the estimated disturbances back into the MPC’s prediction model, which forms a robust adaptive controller with a parameter-varying model. The proposed control strategy is validated through simulations in a Gazebo and Robot Operating System (ROS) environment. The results show that it can effectively reject unpredictable disturbances and improve the UUV’s control performance.

Traffic congestion and frequent traffic accidents have become main problems affecting urban traffic. Effective location prediction of vehicle trajectory can help alleviate traffic congestion, reduce the occurrence of traffic accidents, and optimize the urban traffic system. Vehicle trajectory is closely related to the surrounding Points of Interest (POI). POI can be considered as the spatial feature and can be fused with trajectory points to improve prediction accuracy. A Local Dynamic Graph Spatiotemporal- Long Short-Term Memory (LDGST-LSTM) is proposed in this paper to extract and fuse the POI knowledge and realize next location prediction. POI semantic information is learned by constructing the traffic knowledge graph, and spatial and temporal features are extracted by combining Graph Attention Network (GAT) and temporal attention mechanism. Moreover, the weights of POI that influence location prediction are visualized to improve the interpretability of the proposed model. The effectiveness of LDGST-LSTM is verified on two datasets, including Chengdu taxi trajectory data in October 2018 and August 2014. The accuracy and robustness of the proposed model are significantly improved compared with the benchmark models.

Polyvinyl alcohol-engineering cementitious composites (PVA-ECC) has been widely applied in bridge deck repairing or widening, the common practice for doing this is that a portion of a bridge is left open to traffic while the closed portion is constructed, which expose the early age PVA-ECC to the vehicle-induced vibrations. However, whether vehicle-induced vibrations affect the tensile performance of early age PVA-ECC remains unknow. The purpose of this study was to conduct laboratory test programs on how much vehicle-induced vibrations during early ages affected the tensile performance of PVA-ECC. A self-improved device was used to simulate the vehicle-induced vibrations, and after vibrating with the designed variables, both a uniaxial tensile test and a grey correlation analysis were performed. The results indicated that: the effects of vehicle-induced vibrations on the tensile performance of early age PVA-ECC were significant, and they generally tended to be negative in this investigation. In particular, for all of the vibrated PVA-ECC specimens, the most negative age when vibrated occurred during the period between the initial set and the final set. We concluded that although vehicle-induced vibrations during the setting periods had no substantial effects on the inherent strain-hardening characteristics of PVA-ECC, the effects should not be ignored.

Aiming at the problem of model error and tracking dependence in the process of intelligent vehicle motion planning, an intelligent vehicle model transfer trajectory planning method based on deep reinforcement learning is proposed, which obtain an effective control action sequence directly. Firstly, an abstract model of the real environment is extracted. On this basis, Deep Deterministic Policy Gradient (DDPG) and vehicle dynamic model are adopted to jointly train a reinforcement learning model, and to decide the optimal intelligent driving maneuver. Secondly, the actual scene is transferred to equivalent virtual abstract scene by transfer model, furthermore, the control action and trajectory sequences are calculated according to trained deep reinforcement learning model. Thirdly, the optimal trajectory sequence is selected according to evaluation function in the real environment. Finally, the results demonstrate that the proposed method can deal with the problem of intelligent vehicle trajectory planning for continuous input and continuous output. The model transfer method improves the model generalization performance. Compared with the traditional trajectory planning, the proposed method output continuous rotation angle control sequence, meanwhile, the lateral control error is also reduced.

This paper attempts to develop a Dynamic Mode Decomposition (DMD) based Reduced Order Model (ROMs) which can quickly but accurately predict the forces and moments experienced by a road vehicle such that they be used by an on-board controller to determine the vehicle's trajectory. DMD can linearize a large dataset of high-dimensional measurements by decomposing them into low-dimensional coherent structures and associated time-dynamics. This ROM then also can be applied to predict the future state of the fluid flow. Existing literature on DMD is limited to low Reynolds number applications. This paper presents DMD analyses of the flow around an idealized road vehicle, called the Ahmed body, at a Reynolds number of 2.7E6. The high dimensional dataset used in this paper was collected from a computational fluid dynamics (CFD) simulation performed using Menter's shear stress transport (SST) turbulence model within the context of Improved Delayed Detached Eddy Simulations (IDDES). The DMD algorithm, as available in literature, was found to suffer nonphysical dampening of the medium-to-high frequency modes. Enhancements to the existing algorithm were explored, and a modified DMD approach is presented in this paper which includes: (a) a requirement of higher sampling rate to obtain higher resolution of data, and (b) a custom filtration process to remove spurious modes. The modified DMD algorithm thus developed was applied to the high Reynolds number, separation dominated flow past the idealized ground vehicle. The effectiveness of the modified algorithm was tested by comparing future predictions of force and moment coefficients as predicted by the DMD-based ROM to the reference CFD simulation data, and found to offer significant improvement.

This work mainly discusses an innovative teaching platform on Unmanned Aerial Vehicle digital mapping for Remote Sensing (RS) education at Wuhan University, underlining the fast development of RS technology. Firstly, we introduce and discuss the future development of the Virtual Simulation Experiment Teaching Platform for Unmanned Aerial Vehicle (VSETP-UAV). It includes specific topics such as the Systems and function Design, teaching and learning strategies, and experimental methods. This study shows that VSETP-UAV expands the usual content and training methods related to RS education, and creates a good synergy between teaching and research. The results also show that the VSETP-UAV platform is of high teaching quality producing excellent engineers, with high international standards and innovative skills in the RS field. In particular, it develops students' practical skills with technical manipulations of dedicated hardware and software equipment (e.g., UAV) in order to assimilate quickly this particular topic. Therefore, students report that this platform is more accessible from an educational point-of-view than theoretical programs, with a quick way of learning basic concepts of RS. Finally, the proposed VSETP-UAV platform achieves a high social influence, expanding the practical content and training methods of UAV based experiments, and providing a platform for producing high-quality national talents with internationally recognized topics related to emerging engineering education.

In the current complex and uncertain macroeconomic situation, improving the inherent resilience of the new energy vehicle industry chain is the key to effectively addressing various risks and challenges, and achieving dynamic balance between high-quality industrial development and industrial chain security. Based on the basic concept of resilience and the actual situation of new energy vehicle industry chain development, this study constructs a comprehensive evaluation index system for the resilience of the new energy vehicle industry chain, which includes four dimensional first-level indicators of coping resistance, adaptive resilience, autonomous control and leading competitiveness. In addition, it is measured by combining the data related to the new energy vehicle industry chain in Changzhou City. Our study shows that the situation on the new energy vehicle industry chain is complicated, and the comprehensive evaluation index system is more favorable for evaluating its resilience level.

As a manifestation of technological innovation achievements, patents reflect the frontier of technological development in the field. This paper constructs a multi-entity patent collaboration network and analyzes its evolution patterns to provide a reference for innovation organizations to grasp the general direction of innovation development and select partners. Based on the data of collaboration patents of two and three organizations in China's new energy vehicles (NEV) industry from 2008 to 2021, this paper constructs higher-order interaction collaboration innovation networks in different periods to analyze the spatial evolution of networks and patent cooperation activities. The results show that the generalized degree distribution of nodes and edges conforms to the power-law distribution. The two-dimensional simplex networks gradually form triangle groups centered on the core nodes, and the importance of key edges is beginning to emerge. Key organizations and partners, including State Grid Corporation of China, Tsinghua University, and China Electric Power Research Institute, will largely determine the direction for the future development of cooperation innovation. The study also reveals that Beijing, Jiangsu, Zhejiang, Guangzhou, and Shanghai are in central positions in the cooperative innovation network, based on their cooperation breadth and depth measures. Additionally, key links formed by Beijing as hubs are not only the center of information exchange but also function as bridges that connect to other regions.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

In order to solve the problem of many constraints and complex navigation environment in the path planning of unmanned surface vehicle(USV), an improved Sparrow search algorithm com-bining Cubic chaotic map and Gaussian random walk strategy was proposed to plan it. Firstly, in the population initialization stage, Cubic chaotic map was used to replace the random generation method of the traditional sparrow search algorithm to optimize the uneven initial distribution of the population and improve the global search ability of the population. Secondly, in the late it-eration of the algorithm, the standard deviation of fitness is introduced to determine whether the population is trapped in the local optimum. If true, the Gaussian random walk strategy is used to perturb the optimal individual and assist the algorithm to escape the local optimum. Thirdly, the chosen water environment is modeled, and the navigation information of the original inland electronic navigation chart(ENC) is preprocessed, gridized, and the obstacle swelling is processed. Finally, the path planning experiments of USV are carried out in inland ENC grid environment. The experimental results show that, compared with the traditional sparrow search algorithm, the average fitness value of the path planned by improved sparrow search algorithm is reduced by 14.8%, and the variance is reduced by 49.9%. The path planned by the algorithm is of good quality and high stability, and combined with ENC, it can provide a reliable path for USV.

This paper presents a cooperative parallel tabu search meta-heuristic for the vehicle routing problem with time windows. It is based on the scheme in which several search threads cooperate by asynchronously exchanging information on the best solutions identified. The exchanges are performed through a mechanism called adaptive memory which holds and manages a pool of solutions. This enforces the asynchronous strategy of information exchanges and ensures the independence of the individual search threads. Each of these independent threads implements a tabu search meta-heuristic. Comprehensive computational experiments and comparisons to best known solutions show that the proposed cooperative parallel tabu search algorithm is able to achieve 48 new best solutions on VRPTW benchmark instances.

Efficient processing of end-of-life lithium-ion batteries of electric vehicles is important and a pressing challenge for a circular economy. Regardless of whether the processing strategy is recycling, repurposing or remanufacturing, the first processing step would usually involve disassembly. As battery disassembly is a dangerous task, efforts have been made to robotise it. In this paper, a robotic disassembly platform using four industrial robots is proposed to automate the non-destructive disassembly of a plug-in hybrid electric vehicle battery pack into modules. The work was conducted as a case study to demonstrate the concept of autonomous disassembly of an electric vehicle battery pack. A two-step object localisation method based on visual information is used to overcome positional uncertainties from different sources and is validated by experiments. Also, the unscrewing system is highlighted, and its functions, such as handling untightened fasteners, loosening jammed screws, and changing the nutrunner adapters with square drives, are detailed. Furthermore, the time required for each operation is compared with that taken by human operators. Finally, the limitations of the platform are reported and future research directions are suggested.

The purpose of this research is to present a thorough evaluation of the energy management system, which consists of hybrid energy storage systems, and its control algorithms, which may be used in electric vehicles. This paper outlines the characteristics of electric vehicles, research methods, analysis of the hybrid energy storage system architecture, converter topology, and energy management techniques. The strength and co-occurrence of keywords over the past ten years are shown in this study using a systematic research framework for performing a literature review and using keyword analysis techniques. The study reveals a pattern of recently and frequently used terms in works of literature. Consequently, their suitability, benefits, and drawbacks are assessed. In this study, the hybrid energy storage system and converter circuit architecture are evaluated and rated. Non-isolate DC-DC converter converter connected to SC is a suitable configuration for the hybrid converter because it is simple to build, reliable, and has minimal loss/weight/cost, which improves vehicle performance. In terms of the application of control strategies, it is shown that deterministic and fuzzy rule-based control techniques are successfully assessed using real-scale vehicle experiments and selected for manufacturing. On the other hand, real-time optimization-based energy management techniques have been effectively shown in lab-scale tests and may be used in a future real-scale vehicle.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

An event-based dynamic output feedback control (DOFC) strategy for unmanned marine vehicle (UMV) systems is concerned. The whole UMV systems are composed of an UMV closed-loop system, a land-based control unit and the communication network. To increase the effectiveness of data transmission in the network channel and better enable the control unit against attack, an adaptive event-triggered mechanism (AETM) is applied. Moreover, a quantizer is installed between the sampler and the control unit. The quantizer further reduces the communication burden. The occurrence of aperiodic denial-of-service (DoS) attack is considered in the channel from the control unit to the UMV system. Sufficient criterion for ensuring global exponential stability of system with an expected H∞ disturbance attenuation index is obtained. Co-design of the dynamic output feedback controller and the AETM is derived. The effectiveness of the proposed approach is verified in the given illustrative simulation. The simulation results indicate that the reduction percentages of yaw angle amplitudes and yaw velocity accumulative error of the UMV system with the control strategy proposed in this paper are 43.2%and 45.9%, respectively, which are 0.3% and 5.8% improvement in both metrics compared to the previously published work.

The application of deep learning in the detection of Synthetic Aperture Radar (SAR) targets has been primarily limited to large objects such as ships and airplanes, with much less popularity in detecting SAR vehicles. The complexities of SAR imaging make it difficult to distinguish small vehicles from the background clutter, creating a barrier to data interpretation and the development of Automatic Target Recognition (ATR) in SAR vehicles. The scarcity of datasets has inhibited progress in SAR vehicle detection in the data-driven era. To address this, we introduce a new synthetic dataset called Mix MSTAR, which mixes target chips and clutter backgrounds with original radar data at the pixel level. Mix MSTAR contains 5,392 objects of 20 fine-grained categories in 100 high-resolution images, predominantly 1478x1784 pixels. The dataset includes various landscapes such as woods, grasslands, urban buildings, lakes, and tightly arranged vehicles, each labeled with Oriented Bounding Box (OBB). Notably, Mix MSTAR presents fine-grained object detection challenges by using the Extended Operating Condition (EOC) as a basis for dividing the dataset. Furthermore, we evaluate 9 benchmark rotated detectors on Mix MSTAR and demonstrate the fidelity and effectiveness of the synthetic dataset. To the best of our knowledge, Mix MSTAR represents the first public multi-class SAR vehicle dataset designed for rotated object detection in large-scale scenes with complex background. Mix MSTAR is available at: https://github.com/TheGreatTreatsby/Mix-MSTAR-mmrotate.

In current electric vehicles, the traction battery is intended to store energy. When designing this battery different parameters must be taken into account in order to arrange the battery/module/cells in the mechanically and thermally safest configuration. Moreover, the battery layout must have a correct dynamic behavior in possible collisions. In the present study, different battery configurations plus added energy absorbers are analyzed. In order to do that, an internal combustion vehicle modeled with finite elements is applied as the reference model. The structural behavior of the different battery configurations in the event of a side collision is examined. Firstly, the safest arrangement is stablished, both with respect to cabin intrusion and thermal runaway propagation. Secondly, the safest arrangement that guarantees the safety of the occupants in the event of a side collision is analyzed but using the MADYMO. This software includes experimentally validated dummies which allow have an insight in the stresses experienced by occupants. On the one hand, the analysis states that the battery pack inclusion in the vehicle increases the stiffness of the car floor, resulting in fewer intrusions in the passenger compartment. Therefore, a greater safety for the occupants is reached. On the other hand, none of the configurations analyzed has shown enough safety against the phenomenon of Thermal Runaway.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

In order to solve the problems of complicated steering control of unmanned vehicles in the field and difficult steering on complex roads, we designed a wheel-track composite vehicle equipped with a novel power differential steering mechanism with dual driving, which drove the steering of the vehicle through the differential rotation of the rear two wheels. The unmanned vehicle was simple to control, small in size, and able to work under the conditions of complex roads, such as hills, mountains, and muddy land. Firstly, a steering mechanism with both differential speed and force was designed to prevent the vehicle from skidding into muddy land and stopping motionless. Secondly, the kinematics model and dynamics model of the two drive shafts and the two output shafts (wheel shafts) were established. Thirdly, according to the relationship between the rotational speed of the two output shafts and the steering radius of the vehicle, the kinematic model of the rotational speed of the two input shafts and the steering radius of the wheel-track composite vehicle was obtained. Finally, according to the test data, the mathematical model of rotational speeds of the two input shafts and the actual steering radius of the vehicle was obtained by neural network fitting, and the maximum relative error between the model results and the actual steering radius value was 3.53%. The combination of power differential steering mechanism and wheel-track composite unmanned vehicle increased the adhesion with the ground and could better adapt to the complex road environment. In conclusion, the unmanned vehicle had the advantages of continuous radius steering, deceleration and torsion increase, differential lock, etc. It was suitable for all-terrain military and civilian vehicles and various special equipment mobile platforms of the walking device, and the research results could provide theoretical references for the steering control and structural optimization of the wheel-track composite vehicle under the environment of complex road surface.

The connectivity level of last-generation vehicles is constantly on the rise. The combined use of Vehicle-To-Everything (V2X) connectivity and autonomous driving can provide remarkable benefits through the optimization of the route and speed trajectory. In this framework, this paper focuses on vehicle eco-driving optimization in a connected environment. The virtual test rig of a premium segment passenger car was used for generating the simulation scenarios. The benefits, in terms of energy and time savings, that the introduction of V2X communication, integrated with cloud computing, can have in a real-world scenario were assessed. The Reference Scenario is a pre-defined Real Driving Emissions (RDE) compliant route, while the simulation scenarios were generated by assuming two different penetration levels of V2X technologies. The associated energy minimization problem is formulated and solved by means of a global optimization algorithm, i.e., Dynamic Programming (DP). The optimization framework includes information coming from the surrounding environment, e.g., traffic lights state, speed limits, distance to travel, etc. The simulations show that introducing a smart infrastructure along with optimizing the vehicle speed in a real-world route can potentially reduce the required energy by 54% while shortening the travel time by 38%. Finally, a sensitivity analysis is performed on the bi-objective optimization cost function to find a set of Pareto optimal solutions, between energy and travel time minimization.

The gravel road pavement has a lower construction cost but poorer performance than the asphalt surface. It also emits dust and deforms under the impact of vehicle loads and ambient air factors. The resulting ripples and ruts are constantly deepening, increasing vehicle vibrations and fuel consumption, reducing safe driving speed and comfort. In this article, existing pavement quality evaluation indexes are analysed, and a methodology for their adaptation for roads with gravel pavement is proposed. This article reports the measured wave depth and length of the gravel pavement profile by the straightedge method of a 160 m long road section in three road exploitation stages. The measured pavement elevation was processed according to ISO 8608, and vehicle frequency response has been investigated using simulations in MATLAB/Simulink. The applied International Roughness Index (IRI) analysis showed that a speed of 30-45 km/h instead of 80 km/h provides the objective results of IRI calculation on the flexible pavement due to a decreasing velocity of vehicle's unsprung mass on a more deteriorated road pavement state. The influence of the corrugation phenomenon of gravel pavement has been explored, identifying specific driving safety and comfort cases. Finally, an increase in the Dynamic Load Coefficient (DLC) at a low speed of 30 km/h on the most deteriorated pavement and a high speed of 90 km/h on the middle-quality pavement demonstrates the demand for timely gravel pavement maintenance and the complicated prediction of a safe driving speed for drivers.

Single and multi-vehicle crashes are a significant issue that causes economic and social costs and has therefore gained attention. This study explored the factors associated with injury severity for both single- and multi-vehicle crashes using over 550,000 crash data points in Japan between 2019 and 2021. We identified the determinants of road infrastructure and traffic control while controlling for driver, vehicle, environmental, and accident characteristics by applying ordered logit and bias-reduced binomial regression models. Our findings are as follows. 1) Traffic control variables did not affect single-vehicle crashes. 2) Guardrails had a higher severity in both single-vehicle crashes and multi-vehicle crashes at intersections. 3) The impact of the centerline differed between intersections and non-intersections for multi-vehicle crashes.  These results of this study provide transportation agencies with important guidance as to the road infrastructure and transport control.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

A lot of previous research have proposed various frameworks and algorithms to optimize routes to reduce the total transportation cost, which accounts for over 70% of overall logistics cost. However, it is very hard to find the cases applied the mathematical models or algorithms to the practical business environment cases, especially daily operating logistics services like convenient stores. Most of previous research have considered the developing an optimal algorithm which can solve the mathematical problem within the practical time while satisfying all constraints such as the capacity of delivery and pick-up, and time windows. For the daily pick-up and delivery service like supporting several convenient stores, it is required to consider the unit transporting container as well as the demand, capacity of trucks, traveling distance and traffic congestion. Especially, the reusable transporting container, trays, should be regarded as the important asset of logistics center. However, if the mathematical model focuses on only satisfying constraints related delivery and not considering the cost of trays, it is often to leave the empty trays on the pick-up points when there is not enough space in the track. In this research, it has been proposed to build the mathematical model for optimizing pick-up and delivery plans by extending the general vehicle routing problem of simultaneous delivery and pickup with time windows while considering left-over cost. With the numerical experiments, it has been proved that the proposed model may reduce the total delivery cost. It may be possible to apply the proposed approach to the various logistics business which uses the reusable transporting container like shipping containers, refrigerating containers, trays, and pallets.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

The vehicles number continuously growing lead to increasingly intense and congested traffic and it will additionally demand the braking system, and drivers behave more aggressively and as result is required that the braking system to be durable and efficient. For this is necessary the study the braking system behavior in conditions of intense and moderate traffic to increase the safety of traffic participants, respectively to demonstrate the need for more frequent replacement of some braking system elements. Thus, on a vehicle were performed a series of successive tests, through which the degree of wear of the brake pads and discs was monitored periodically and as a result the efficiency evolution of the braking system. The tests were carried out both in laboratory (on dynamometer) and in traffic to establish the efficiency of the braking system according to some parameters considered essential. The experimental tests showed that the recommendations regarding the frequency of replacement of brake pads and disks are inconsistent with their actual wear. Therefore, the aim of this paper is the establishment of the braking system efficiency of an auto-vehicle, subject to testing depending on the auto-vehicle mass, travel speed, distance driven, and braking time, based on experimental on stand and in-traffic tests, according the road safety regulations.

Connected and Autonomous Vehicle (CAV) combines technologies of autonomous vehicle (AV) and connected vehicles (CV) to develop quicker, more reliable and safer traffic. Artificial Intelligence (AI) based CAV solutions play significant roles in sustainable city. The convergence imposes stringent security requirements for CAV safety and reliability. In practice, vehicles are developed with increased automation and connectivity. Increased automation increases the reliance on the sensor-based technologies and decreases the reliance on driver; increased connectivity increases the exposures of vehicles vulnerability and increases the risk for an adversary to implement a cyber-attack. Much work has been dedicated to identifying the security vulnerabilities and recommending mitigation techniques associated with different sensors, controllers, and connection mechanisms, respectively. However, there is an absence of comprehensive and in-depth studies to identify how the cyber-attacks exploit the vehicles vulnerabilities to negatively impact the performance and operations of CAV. In this survey, we set out to thoroughly review the security issues introduced by AV and CV technologies, analyze how the cyber-attacks impact the performance of CAV, and summarize the solutions correspondingly. The impact of cyber-attacks on the performance of CAV is elaborated from both viewpoints of intra-vehicle system and inter-vehicle system. We pointed out that securing the perception and operations of CAV would be the top requirement to enable CAV to be applied safely and reliably in practice. Also, we suggested to utilize cloud and new AI methods to defend against smart cyber-attacks on CAV.

With the automotive industry moving towards automated driving, sensing is increasingly important in enabling technology. The virtual sensors allow data fusion from various vehicle sensors and provide a prediction for measurement that is hard or too expensive to measure in another way or in the case of demand on continuous detection. In this paper, virtual sensing is discussed for the case of vehicle suspension control, where information about the relative velocity of the unsprung mass for each vehicle corner is required. The corresponding goal can be identified as a regression task with multi-input sequence input. The hypothesis is that the state-of-art method of Bidirectional Long-Short Term Memory (BiLSMT) can solve it. In this paper, a virtual sensor has been proposed and developed by training a neural network model. The simulations have been performed using an experimentally validated full vehicle model in IPG Carmaker. Simulations provided the reference data which was used for Neural Network (NN) training. The extensive dataset covering 26 scenarios has been used to obtain training, validation and testing data. The Bayesian Search was used to select the best neural network structure using root mean square error as a metric. The best network is made of 167 BiLSTM, 256 fully connected hidden units and 4 output units. Error histograms and spectral analysis of the predicted signal compared to the reference signal are presented. The results demonstrate the good applicability of neural network-based virtual sensors to estimate vehicle unsprung mass relative velocity.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

Bandung and Lembang are the cities that are chosen by many tourists (local and foreign) as their destinations. Geographically, these cities are placed side-by-side and each city has its own characteristics. As in Bandung, there are many hotels and culinary spots, meanwhile, in Lembang, there are many scenery tourism spots. Tourists usually have limited time to visit all the destinations on holiday, which makes them choose several tourist destinations to visit. In this paper, the tourism itinerary recommendation system is proposed by calculating the most optimal route between destinations and approaching the Vehicle Routing Problem with Time Windows. The optimal route is defined by using Dijkstra the shortest path algorithm by using the collaboration between the road information (road length, traffic condition, travel time, and weather condition) and criteria weight that is determined using the Analytics Hierarchy Process as the graph weights. According to the simulation results, the criteria weights are 6.9%, 62.7%, 18.6%, and 11.9% for Route Length, Traffic Condition, Travel Time, and Weather Condition respectively. Moreover, the optimal number of tourism itinerary plans for the tourist in this research is 4 destinations. As the usage of computational resources, it takes 31.8% of CPU and 61.9% of Memory usage. For the time processing, it increases exponentially as the increment of number of requested stops. The output of this research is expected to be a solution to the tourist itinerary plan, especially in Bandung and Lembang.

Background: Previous investigations have found a correlation between abnormal curvatures and a variety of patient complaints such as cervical pain and disability. However, no study has shown that loss of the cervical curve is a direct result of exposure to a motor vehicle collision (MVC). This investigation presents a retrospective consecutive case series of patients with both a pre-injury cervical lateral radiograph (CLR) and a post-injury CLR after exposure to a MVC. Computer analysis of digitized vertebral body corners on CLRs was performed to investigate the possible alterations in the geometric alignment of the sagittal cervical curve. Methods: Three spine clinic records were reviewed, over a 2-year period, looking for patients where both an initial lateral cervical x-ray and an examination were performed prior to the patient being exposed to a MVC; afterwards an additional exam and radiographic analysis were required. A total of 41 patients met the inclusion criteria. Examination records of pain intensity on numerical pain rating scores (NPRS) and neck disability index (NDI), if available, were analyzed. The CLRs were digitized and modeled in the sagittal plane using curve fitting and the least squares error approach. Radiographic variables included total cervical curve (ARA C2-C7), Chamberlain’s line to horizontal (skull flexion), horizontal translation of C2 relative to C7, segmental translations (retrolisthesis and anterolisthesis), and circular modelling radii. Results: There were 15 males and 26 females with an age range of 8-65 years. Most participants were drivers (28) involved in rear end impacts (30). The pre-injury NPRS was 2.7 while the post injury was 5.0; p &lt; 0.001. The NDI was available on 24 /41 (58.5%) patients and was found to increase following exposure to the MVC: 15.7% to 32.8%, p &lt; 0.001. An altered cervical curvature was identified following exposure to MVC, characterized by an increase in radius of curvature and an approximate 8° reduction of lordosis from C2-C7; p &lt; 0.001. The mid cervical spine (C3-C5) showed the greatest curve reduction with localized mild kyphosis at these levels on average. Several participants developed segmental translations that approached the instability value of translation &gt; 3.5mm. Conclusions: Abnormalities of cervical lordosis occurred following exposure to a MVC. The average loss of cervical curvature was 8° from C2-C7, with mild flexion of the mid cervical segments. Snap through type or dynamic buckling during the MVC may explain our findings. The primary contribution of this study to the motor vehicle collision literature is that altered cervical lordosis may result from MVC exposures and the consequences of an altered cervical alignment, in turn, may lead to future pain, disability and decreased health-related quality of life.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

This study aims to develop a hybrid approach based on backpropagation Artificial Neural Network (ANN) and spatial analysis techniques to predict particulate matter of size 2.5 µm (PM2.5) from vehicle exhaust emissions in the State of California using Aerosol Optical Depth (AOD) and several climatic indicators (relative humidity, temperature, precipitation, and wind speed). The PM2.5 data were generated using Motor Vehicle Emission Simulator (MOVES), the measured climatic variables and AOD were obtained from the California Irrigation Management Information System (CIMIS), and NASA’s Moderate Resolution Spectroradiometer (MODIS). The data were resampled to a seasonal format and downscaled over grids of 10 by 10 to 150 by 150, and precipitation was determined to be the most important independent variable. Coefficient of determination ( ), Mean Absolute Percentage Error (MAPE), and Root Mean Square Error (RMSE) were used to assess the quality of the ANN prediction model. The model peaked at winter seasons with = 0.984, RMSE = 0.027, and MAPE = 25.311, whereas it had the lowest performance in summer with = 0.920, RMSE = 0.057, and MAPE = 65.214. These results indicate that the ANN model can accurately predict the PM2.5 concentration and can be used to forecast future trends.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

This research focuses on the development of an automated medication delivery system using Unmanned Aerial Vehicle (UAV) Technology and the Internet of Things (IoT) to support telemedicine and community welfare in the KLU region. The system is designed to improve the quality of medical services and medication management for the community in the area. One of the main challenges faced is how the KLU community responds and accepts automatic medication delivery using UAVs and IoT. To overcome this challenge, this research suggests providing education and training to the community about the benefits and usage of the system, as well as displaying a working simulation of the system to the community.

Unmanned aerial vehicles (UAVs) represent a new model of social robots for home care of dependent persons. In this regard, this article introduces a study on people’s feeling of safety and comfort while watching the monitoring trajectory of a quadrotor dedicated to determining their condition. Three main parameters are evaluated: the relative monitoring altitude, the monitoring velocity and the shape of the monitoring path around the person (ellipsoidal or circular). For this purpose, a new trajectory generator based on a state machine, which is successfully implemented and simulated in MATLAB/Simulink®, is described. The study is carried out with 37 participants using a virtual reality (VR) platform based on two modules, UAV Simulator and VR Visualiser, both communicating through the MQTT protocol. The participants’ preferences have been a high relative monitoring altitude, a high monitoring velocity and a circular path. These choices are a starting point for the design of trustworthy socially assistive UAVs flying in real homes.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.