The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

Wear usually occurs in the loaded part of hydrodynamic bearings and leads the bearing geometry imperfections. This paper investigates the effects of wear-induced geometric imperfections of tilting pad journal bearings (TPJBs) on the dynamic behavior of the system. Furthermore, the effect of wear on the journal-bearing rub-induced contact pressure severity is investigated. A novel tribo-dynamic model is proposed for a flexible rotor-worn TPJB which integrates a mixed elastohydrodynamic model with a rotor-worn TPJB thermal and dynamic model to assess the effects of the bearing wear progression on the rotor-TPJB behavior. Based on the results, wear changes the temperature distribution of the pads and oil film as well as the dynamic behavior of the system. Dynamic simulations reveal a higher vibration level and contact pressure for the worn TPJBs near the system's critical speed and service speed. Finally, thermal and dynamic condition indicators are suggested to detect TPJB wear severity at its early stages.

Disposable absorbent hygiene products have evolved for superior performance, enhancing the convenience of daily lives. Yet the use of disposable hygiene pads has brought safety concerns on chemical exposure, and significant efforts have been made to assess the potential risks associated with use of hygiene pads. This article intends to overview the safety assessment framework of diapers and feminine pads, which includes hazard identification, hazard characterization, exposure assessment, risk characterization, and postmarket risk management. Risk assessment of various constituents are reviewed for quantification methods and conservative estimation of exposure parameters. By reviewing the up-to-date considerations in risk assessment, we aim to provide insightful discussion on safety evaluation of current versions of disposable absorbent products. More clinical testing and postmarket surveillance are needed for continuous monitoring of potential health impacts of advanced products and constituents.

Atherosclerosis is a dynamic, chronic and progressive process that involves the vascular bed (coronary and peripheral). Risk factors are associated with the progression rate and with the evolution of atherosclerosis. There are traditional risk factors and non-traditional risk factors, all of them lead to endothelial dysfunction. Endothelial dysfunction plays a key factor in atherosclerosis. It accompanies hypercholesterolemia, diabetes, hypertension, cigarette smoking – leading to the development of atherosclerosis. Endothelial dysfunction can be reversed by treating hyperlipidemia and other damaging processes, and the mechanism is believed to be associated with an increase in vascular endogenous NO. PAD is a devastating disease, leading to leg pain and amputation. Until now the optional treatments don’t cure or prevent the uneventful outcome, but may slow the downhill progression. We summarize the updated knowledge of the management of PAD and suggest a novel approach to treat patients with PAD, using stem cells technology and a special novel endovascular device that will deliver the cells continuously on the long run and may halt the progression of atherosclerosis or even cure PAD.

This study outlines the development of an innovative method utilizing UHPLC-PDA for the simultaneous identification of polyphenols and bitter acids (alpha-acids, beta-acids, and iso-alpha-acids) in beer samples. The resulting chemical profiles were leveraged to distinguish the characteristics of four bergamot-flavored beers, each representing distinct styles (IPA, Lager, Blanche, and ALE), produced on a pilot-scale plant. In a streamlined 29-minute analysis, twenty-nine polyphenols and fourteen bitter acids were successfully identified under optimized separation conditions. Rigorous validation, encompassing parameters such as Limit of Detection (LOD), Limit of Quantification (LOQ), R-squared (R2), repeatability, and reproducibility, was conducted for polyphenol quantification using constructed calibration curves with seven levels. Exploring polyphenolic components as potential discriminators among different beer styles, a total of thirty-two polyphenolic compounds were identified and quantified, including characteristic bergamot peel polyphenols like neoeriocitrin, naringin, and neohesperidin. The determination of bitter units and total phenols further aided in style differentiation. Multivariate analysis provided additional insights into variations among specific beer styles, revealing discrepancies in the presence or relative concentrations of specific compounds linked to brewing ingredients and processes. This research enhances to trace the fingerprinting of the chemistry governing beer quality through a straightforward and cost-effective analytical approach, readily applicable in common laboratories.

Drainage divide is a dynamic feature that migrates in response to tectonic activity. The asymmetric uplift between two adjacent basins causes the divide migration from a slower to faster uplift area. Sado Island, Japan, has been affected by southeastward tilting uplift since ca. 300k years. Despite the faster uplift on the northwest, the main divides have existed on the southeast side of the geometric center of the island, with no other feature suggesting tectonic inversion of the tilting direction. In this study, we conducted a DEM-based investigation that focused on divide migration. A spectrum from very inactive to active divide migration in the northwest. Regardless of their position, actively migrating divides are comprehensible, but inactive divides located in a relatively slow uplift area remain unclear. We concluded that some divides slowed down owing to the local balance of erosion rates across the divides, not implying the balance between uplift and river erosion at the basin scale, reflecting disequilibrium in river longitudinal profiles. The main divides of Sado have presumably continued to slowly migrate toward the faster uplift area; however, they are most likely to have never overcome the moving geometric center owing to land expansion at the seacoast due to asymmetric uplift.

A reliability-based criterion to estimate strength amplification factors for buildings with asymmetric yielding located within a seismic region presenting different soil conditions is proposed and applied. The approach involves the calculation of the mean annual rate of exceedance of structural demands of systems with different levels of asymmetric yielding. Two simplified mathematical expressions are developed considering different soil conditions of the valley of Mexico. The mathematical expressions depend on the ductility of the structural systems, their level of asymmetric yielding, their fundamental vibration period and the dominant period of the soil. In addition, the proposed expressions are compared with that recommended by the current Mexico City Building Code (MCBC). Since the expressions are developed with the help of simplified structural systems, the validity of such expressions is corroborated by comparing the expected ductility demand of multi-degree of freedom (MDOF) structural systems with respect to that of their equivalent simplified systems. Both structural representations are associated with a given annual rate of exceedance value of an engineering demand parameter. The expressions proposed in this study will be incorporated in the new version of the MCBC.

The process of establishing secure communication between devices in the Internet of Things (IoT) can be approached by using a One-time-Pad (OTP) protocol. We propose using a known secure multiparty sum protocol for generating a One-time-Pad key using true (physical) random numbers in each device (party). We implemented the proposal using ZeroC-Ice, a middleware for distributed computing. The protocol security properties were analyzed under the assumptions of the Dolev-Yao threat model.

Trash mulches are very effective in preventing soil erosion; reduce sediment transport rate, runoff rate and increasing infiltration. The study was carried out with the objectives to observe the sediment outflow from sugar cane leaf (trash) mulch treatments at selected land slopes under simulated rainfall conditions by using rainfall simulator of size 10 m × 1.2 m × 0.5 m with the locally available soil material collected from Pantnagar. In the present study, trash mulches with different quantities were selected to observe the effect of mulching in soil loss reduction. The quantity of mulch was taken as, 6 t/ha, 8 t/ha and 10 t/ha, three rainfall intensities viz. 11cm/h, 13cm/h and 14.65cm/h at 0%, 2% and 4% land slopes were selected. The duration of rainfall was fixed (10 minutes) for every mulch treatment. The total runoff volume was found to be varying with different mulch rates for particular rainfall input and land slope. The runoff distribution pattern was observed to be increasing with the increase in land slope. The average sediment concentration (SC) and outflow was found to be increasing with the increasing land slope, but SC and outflow decreased with increasing mulch rate for particular land slope and rainfall intensity. The SOR (SOR) for no mulch treated land was higher as compared to trash mulch treated lands. Mathematical relationships were developed for relating SOR, SC, land slope and rainfall intensity for a particular mulch treatment. It was observed that values of SOR and average SC had a good correlation with rainfall intensity and land slope for each mulch treatment. The correlation coefficients of developed models were found to be more than 90%.

Incorporating linear-scanning MEMS micromirrors into Fourier transform spectral acquisition systems can greatly reduce the size of the spectrometer equipment, making portable Fourier transform spectrometers (FTS) possible. How to minimize the tilting of the MEMS mirror plate during its large linear scan is a major problem in this application. In this work, an FTS system has been constructed based on a biaxial MEMS micromirror with a large piston displacement of 180 μm, and a biaxial H∞ robust controller is designed. Compared with open-loop control and PID closed-loop control, H∞ robust control has good stability and robustness. The experimental results show that the stable scanning displacement reaches 110.9 μm under the H∞ robust control, and the tilting angle of the MEMS mirror plate in that full scanning range falls within ±0.0014°. Without control, the FTS system cannot generate meaningful spectra. In contrast, the FTS yields a clean spectrum with an FWHM spectral linewidth of 96 cm-1 under the H∞ robust control. Moreover, the FTS system can maintain good stability and robustness under various driving conditions.

Various UAV applications, especially those based on reconnaissance and observation missions, often require an unlimited time of flight. This is possible only when a UAV is being continuously power supplied from the ground power source, and that is why tethered UAV systems were developed. Tethered UAV systems are based on multicopters which can hover above the landing pad, or track its position in the case it is movable. The presented research is about the development of a large C3 class hexacopter having a maximal payload of about 1 kg, and takeoff mass of 16 kg, which was tested in maritime conditions during the ferry’s cruise. The main purpose of the hexacopter is the continuous observation of the area ahead of a vessel to detect and localize obstacles in the water. During experimental tests critical phases of flight were identified, the AC-DC power supply unit as well as the power cord unwinder were tested, and the power taken by six BLDC motors was registered. The obtained results can be useful in future work on tethered UAV systems used in windy maritime conditions.

The COVID-19 pandemic has left no one indifferent: all around the globe, people have felt the massive impact of a virus that has stopped the world in its tracks. Many countries have been forced to impose strict lockdowns, causing devastating damage to the overall economy and welfare state, but also leaving an unprecedented emotional footprint on almost everyone. In this paper, we aim to quantify, by building our own method how, this pandemic has affected people emotionally by detecting the shifts in the emotional profile of representative users in selected countries. Our method processes the social media stream adapting the Pleasure-Arousal-Dominance (PAD) approach to measure emotional states on the Russell Circumplex plane, allowing for not only an overall emotional shift quantification but also a detailed analysis at mood level. By focusing on certain emotions and searching behavior, we establish a relationship between the pandemic and the emotional response. Although the method can be applied to any location with a significant and varied amount of geo-localized social media streams, the scope of this paper covers the most representative cities in Europe.

Personal Mobility Vehicle (PMV) which has an inward tilting angle turns with the lateral force due to large camber angle, so it is necessary to consider the lateral movement of the tire vertical load axis during turning. Although the steering torque mechanism are very different from those of automobiles, there are not many examples which studied the steering torque mechanism of PMV. In this paper, based on the effects of six components force acting on the tires, a method for setting the steering axis specifications is derived, including the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. Although, automobile tires have a significant ground camber angle when traveling on rutted roads, they do not have it on slant roads because the vehicle body tilts along the road surface. On the other hand, in PMV, the vehicle body always keeps upright when traveling both on slanted roads and on rutted roads. Therefore, the tires have ground camber angles on both types of road surface. We study the straight running ability under such road surface disturbances based on the geometrical minimization of steering moment disturbance due to the vertical load reaction force during turning. This straight running ability can be a remarkable strong point of PMV with an inward tilt mechanism.

General Linear Modelling (GLM) has been widely employed to estimate the hemodynamic changes evoked by cognitive processing, which are more likely to be nonlinear than linear. First, this study re-analyzed the fNIRS data (N = 38, Mage = 5.0 years, SD = 0.69 years, 17 girls) collected in the Mixed-Order Design Dimensional Change Card Sort (DCCS) task. The results indicated that the quadratic equation was better than GLM to model HbO changes in this task. Second, analysis of a new set of data indicated that the Habit-DisHabit design of DCCS was more effective in identifying the neural correlates of cognitive shifting than the Mixed-Order Design. Third, this study found that the Non-users were more attentive and engaged than the Heavy-users, with a slower but more steady increase of brain activation in BA8 and BA9.

This study aims to examine the impact of tablet use on preschoolers’ executive function during the Dimensional Change Card Sort Task (DCCS) task using the functional near-infrared spectroscopy (fNIRS). Altogether 38 Chinese preschoolers (Mage = 5.0 years, SD = 0.69 years, 17 girls) completed the tasks before the COVID-19 lockdown. Eight children never used tablets, while 16 children were diagnosed as the ‘heavy-user'. The results indicated that: (1) the 'Non-user' outperformed the 'Heavy-user' with a significantly higher correct rate in the DCCS task; (2) the two groups differed significantly in the activation of the prefrontal cortex (BA 9): the 'Non-user' pattern is normal and healthy, whereas the 'Heavy-user' pattern is not normal and needs further exploration.

One of the most important pieces of equipment used in labs in culturing populations of fruit flies (Drosophila sp.) is that of the “CO₂ gas plate”, which is used to anesthesize individuals during “fly-pushing”. This piece of equipment consists of a box with a porous top into which carbon-dioxide is pumped. Flies placed on its surface are left immobilized, permitting the sorting, categorizing and/or counting of flies during population culturing and experimental assays. Unfortunately, commercially available gas plates are typically expensive. Here, we describe a new design for a gas plate that can be easily produced using a 3D printer and a laser cutter, which we are making freely available to the fly community.

The onset and progression of human inflammatory joint diseases are strongly controlled by the activation of resident synovium/infrapatellar fat pad (IFP) pro-inflammatory and pain-transmitting signaling. We recently reported that intra-articularly injected IFP-derived Mesenchymal Stem/Stromal Cells (IFP-MSC) acquire a potent immunomodulatory phenotype and actively degrade Substance P (SP) via neutral endopeptidase CD10 (neprilysin). Our hypothesis is that IFP-MSC robust immunomodulatory therapeutic ef-fects are largely exerted via their CD10-bound exosomal secretome (IFP-MSC EXOs) by attenuating synoviocyte pro-inflammatory activation and articular cartilage degradation. Herein, IFP-MSC EXOs were isolated from CD10High- and CD10Low-expressing IFP-MSC cultures and their exosomal miRNA cargo was assessed using multiplex methods. Functionally, we interrogated the effect of CD10High and CD10Low EXOs on stimulated by inflammatory/fibrotic cues synoviocytes monocultures and cocultures with IFP-MSC de-rived chondropellets. Finally, CD10High EXOs were tested in vivo for their therapeutic capacity in an animal model of acute synovitis/fat pad fibrosis. Our results showed that CD10High and CD10Low EXOs possess distinct miRNA profiles. Reactome analysis of miRNAs highly present in exosomes showed their involvement in the regulation of six gene groups, particularly the immune system. Stimulated synoviocytes exposed to IFP-MSC EXOs demonstrated significantly reduced proliferation and altered inflammation-related molecular profiles compared to control stimulated synoviocytes. Importantly, CD10High EXOs treatment of stimulated chondropellets/synoviocytes cocultures indicated a significant chondroprotective effects. Therapeutically, CD10High EXOs treatment resulted in robust chondroprotective effects by retaining articular cartilage structure/composition and PRG4 (lubricin)-expressing cartilage cells in the animal model of acute synovitis/IFP fibrosis. Our study suggests that CD10High EXOs possess immuno-modulatory miRNA attributes with strong chondroprotective/anabolic effects for articular cartilage in vivo. The results could serve as a foundation for EXOs-based therapeutics for the resolution of detrimental aspects of immune-mediated inflammatory joint changes associated with conditions such as osteoarthritis (OA).

Background: Vascular inflammation plays a crucial role in peripheral arterial disease (PAD), although the role of the mediators involved has not yet been properly defined. The aim of this work is to investigate gene expression and plasma biomarkers in chronic limb-threating ischemia (CLTI). Methods: Using patients from the GHAS trial, both blood and ischemic muscle samples were obtained to analyze plasma markers and mRNA expression, respectively. Statistical analy-sis was performed by using univariate (Spearman, t-Student, X2) and multivariate (multiple lo-gistic regression) tests. Results: 35 patients were available at baseline (29 for mRNA expression). Baseline characteristics (mean): Age:71.4±12.4 (79.4% male); TNF-α:10.7±4.9; hs-CRP:1.6±2.2; Neutrophil-to-lymphocyte ratio (NLR):3.5±2.8. Plasma TNF-α was found elevated (≥8.1) in 68.6% of patients, while high hs-CRP (≥0.5) in 60.5%. Diabetic patients with high level of inflammation showed significantly higher levels of NOX4 expression at baseline (p=0.0346). Plasma TNF-α had a negative correlation with eNOS expression (-0.5, p=0.015) and hs-CRP with VEGF-A (-0.63, p=0.005). The expression of NOX4 was parallel to that of plasma TNF-α (0.305, p=0.037), especial-ly in DM. Cumulative mortality at 12-month was related to NLR ≥3 (p=0.019) and TNF-α ≥8.1 (p=0.048). The best cut-off point for NLR to predict mortality was 3.4. Conclusions: NOX4 and TNF-α are crucial for the development and complications of lower limb ischemia, especially in DM. hs-CRP could have a negative influence on angiogenesis too. NLR and TNF-α represent suita-ble markers of mortality in CLTI. These results are novel because they connect muscle gene expres-sion and plasma information in patients with advanced PAD, deepening the search of new and ac-curate targets for this condition.

Finding out how cells with the same genome change fates in differentiation commitment is a challenge of biology. We used MCF-7 breast cancer cells treated with the ErbB2 ligand heregulin (HRG), which induces differentiation, to address if and how the constitutive pericentromere-associated domains (PADs) may be involved in this process. PAD-specific repressive heterochromatin (H3K9me3) and active euchromatin (H3K4me3) marking, centromere (CENPA) labelling, qPCR, acridine-orange-DNA structural test, and microscopic image analysis were applied. We found a two-step DNA unfolding, at 15-20 min and 60 min after HRG treatment, coinciding with bi-phasic activation of the early response genes (c-FOS family) and two steps of critical phase transition which were revealed in transcriptome studies. In control, the distribution of PAD number and size displays a power-law scaling with a boundary at the nucleolus. PADs’ clustering correlates with centromere numbers. 15 min after HRG treatment, the unravelling of PADs occurs, coinciding with the first step of euchromatin unfolding. The second step is associated with transcription of long-non-coding-RNA from satellite III DNA. We hypothesize that splitting of the PAD clusters under the critical size threshold of the silencing domain abrupts position effect variegation. It allows the first genome transcription avalanche to occur, starting differentiation commitment.